Thermalright. TRUE Spirit 140 BW Rev.A

Transcription

1 Thermalright

2

3 Assembly Package Chill Factor g 8

4 Intel 775/50/55/56/66 Exploded View Important! Before proceeding with installation, please check for the most up-to-date instructions at Heatsink Body cm Fan Clip TY7 FAN Anti Vibration Pad M L6 Screw Anchoring Mount Screw Nut Mounting Plate Intel Washer (small) M L0 Screw

5 Component Chill Factor g 5 6 Heatsink Body Mounting Plate 5 7 M L0 Screw 5 8 Anchoring Mount Screw Nut M L6 Screw Metal Back Plate LGA0 Type B Screw Pillars x cm Fan Clip 0 6 Intel Washer (small) Back Plate Cap Mylar AMD Washer (big) Thermal Paste 5 Anti Vibration Pad 8 TY7 Fan The Ultimate Cooling Solutions!

6 Installation Instructions: Step : Step : Fan Clip Installation Take out TRUE Spirit 0 heat-sink body from the box. Apply Anti-Vibration Paddings to corners of the Heatsink fin stack. Pull both ends of the Fan clip and make them go through holes on the corners of the heat-sink. Repeat for the second fan clip on the other side of the fin stack. Leave the two fan clips on the Heatsink Body for fan install later on. Do not remove them. Step : Step : Back Plate Installation Choose the platform (LGA 775/50/55/56/66) you are in use. Make four ML0 Screw Pillars go through the Metal Back Plate and the Mylar film from bottom towards top.and then place the Metal Back Plate on the table. Put the four Washers (for Intel) around the Screw Pillars. Step : Step : Step : 775 Back Plate cap Note: When installing on a 775 platform, please first insert the Back Plate Cap into the opening on the Back plate, make sure you have the Cap facing downwards. Only for LGA775 platform, all other platforms go directly to Step. Step : Place the motherboard on top of the Back Plate. See the four Screw Pillars go through the four holes around the processor socket. Cap the four Screw Pillars with the four Screw Nuts in a criss-cross pattern.make sure the side with a washer is facing the Back Plate.

7 Chill Factor g Step 5: Step 6: Chill Factor g Step 5 : Anchoring Mount Installation Place the Anchoring Mount on the Screw Nuts. Use the four ML6 Screws to fix the Anchoring Mount on to the Screw Nuts. Step 6 :Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. (A flat edge, like a business card or an old credit card would be beneficial in spreading the thermal paste.) Step 7: Step 7 : Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And then use the two ML6 screws to secure the Mounting Plate, one side at a time in several turns to ensure balanced mounting. Step 8: Step 9: Step 8 : Fan Installation Place the included TY-7 fan onto the Heatsink body. And then secure it with the Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the TY-7 fan. Step 9 : Installation completed Connect the TY-7 fans to the CPU PWM Fan socket on the motherboard. Installation complete.

8 Intel 0 Exploded view Important! Before proceeding with installation, please check for the most up-to-date instructions at Heatsink Body cm Fan Clip TY7 FAN Anchoring Mount Anti Vibration Pad M L6 Screw LGA0 Type B Screw Pillars Mounting Plate 5

9 Component Chill Factor g 5 6 Heatsink Body Mounting Plate 5 7 M L0 Screw 5 8 Anchoring Mount Screw Nut M L6 Screw Metal Back Plate LGA0 Type B Screw Pillars x cm Fan Clip 0 6 Intel Washer (small) Back Plate Cap Mylar AMD Washer (big) Thermal Paste 5 Anti Vibration Pad 8 TY7 Fan The Ultimate Cooling Solutions! 6

10 Installation Instructions: Step : Step : Fan Clip Installation Take out TRUE Spirit 0 heat-sink body from the box. Apply Anti-Vibration Paddings to corners of the Heatsink fin stack. Pull both ends of the Fan clip and make them go through holes on the corners of the heat-sink. Repeat for the second fan clip on the other side of the fin stack. Leave the two fan clips on the Heatsink Body for fan install later on. Do not remove them. Step : Step : Anchoring Mount Installation Place the Anchoring Mount onto the four LGA0 Type B Screw Pillars, secure it by tightening it with ML6 Screws. Step : Step : Screw Pillar Installation Screw on the four LGA0 Type B Screw Pillars into the Heatsink studs on the ILM Assembly Frame around the processor socket. 7

11 Step : Step 5: Chill Factor g Chill Factor g Step : Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. (A flat edge, like a business card or an old credit card would be beneficial in spreading the thermal paste.) Step 6: Step 5 : Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And then use the two ML6 screws to secure the Mounting Plate, one side at a time in several turns to ensure balanced mounting. Step 6 : Fan Installation Place the included TY-7 fan onto the Heatsink body. And then secure it with the Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the TY-7 fan. Step 7: Step 7 : Installation completed Connect the TY-7 fans to the CPU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions! 8

12 AM/AM+/AM/AM+/FM/FM Exploded View Important! Before proceeding with installation, please check for the most up-to-date instructions at Heatsink Body cm Fan Clip TY7 FAN M L6 Screw Anti Vibration Pad Anchoring Mount Screw Nut Mounting Plate AMD Washer (big) M L0 Screw 9

13 Component Chill Factor g 5 6 Heatsink Body Mounting Plate 5 7 M L0 Screw 5 8 Anchoring Mount Screw Nut M L6 Screw Metal Back Plate LGA0 Type B Screw Pillars x cm Fan Clip 0 6 Intel Washer (small) Back Plate Cap Mylar AMD Washer (big) Thermal Paste 5 Anti Vibration Pad 8 TY7 Fan The Ultimate Cooling Solutions! 0

14 Installation Instructions: Step : Step : Fan Clip Installation Take out TRUE Spirit 0 heat-sink body from the box. Apply Anti-Vibration Paddings to corners of the Heatsink fin stack. Pull both ends of the Fan clip and make them go through holes on the corners of the heat-sink. Repeat for the second fan clip on the other side of the fin stack. Leave the two fan clips on the Heatsink Body for fan install later on. Do not remove them. Step : AMD Step : Back Plate Installation Choose the platform (AMD) you are in use. Make four ML0 Screw Pillars go through the Metal Back Plate and the Mylar film from bottom towards top.and then place the Metal Back Plate on the table. Put the four Washers (for AMD) around the Screw Pillars. Step : Step : Step : Back Plate Cap Note: When installing on an AMD platform, please first insert the Back Plate Cap into the opening on the Metal Back plate, make sure you have the Cap facing downwards. Step : Place the motherboard on top of the Back Plate. See the four Screw Pillars go through the four holes around the processor socket. Cap the four Screw Pillars with the four Screw Nuts in a criss-cross pattern.make sure the side with a washer is facing the Back Plate.

15 Step 5: Step 6: Chill Factor g Chill Factor g Step 5 : Anchoring Mount Installation Place the Anchoring Mount on the Screw Nuts. Use the four ML6 Screws to fix the Anchoring Mount on to the Screw Nuts. Step 6 :Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. (A flat edge, like a business card or an old credit card would be beneficial in spreading the thermal paste.) Step 7: Step 7 : Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And then use the two ML6 screws to secure the Mounting Plate, one side at a time in several turns to ensure balanced mounting. Step 8: Step 9: Step 8 : Fan Installation Place the included TY-7 fan onto the Heatsink body. And then secure it with the Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the TY-7 fan. Step 9 : Installation completed Connect the TY-7 fans to the CPU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions!

16 Technical Spec Heatsink Specifications: Dimension: Length 55mm x Width 5.mm x Height 65.5mm Weight: 60g (Heatsink only) Heatpipe: 6mm heatpipe*6 units Copper Base: C00 Pure copper nickel plated Fan Specification: Dimension: L5mm x H0mm x W6.5m Weight: 60g Fan speed: 900~00 RPM (-Pin PWM) Fan noise: 7~ dba MAX (-Pin PWM) Airflow: 8.~7.6 CFM MAX Connector: Pin (PWM Fan connector)

17 The Ultimate Cooling Solutions!

18 5

19 The Ultimate Cooling Solutions! TEL: FAX: The Ultimate Cooling Solutions! 6