B. Product Schedule: For appliances. Use same designations indicated on Drawings.

Transcription

1 SECTION RESIDENTIAL APPLIANCES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Cooking appliances (micro-wave oven). 2. Refrigeration appliances (up-right and under-counter refrigerators). 3. Cleaning appliances (washers and dryers). 1.3 ACTION SUBMITTALS A. Product Data: For each type of product indicated. Include rated capacities, operating characteristics, dimensions, furnished accessories, and finishes for each appliance. B. Product Schedule: For appliances. Use same designations indicated on Drawings. 1.4 INFORMATIONAL SUBMITTALS A. Product Certificates: For each type of appliance, from manufacturer. 1.5 CLOSEOUT SUBMITTALS A. Operation and Maintenance Data: For each residential appliance to include in operation and maintenance manuals. 1.6 QUALITY ASSURANCE A. Source Limitations: Obtain residential appliances from single source and each type of residential appliance from single manufacturer. B. Regulatory Requirements: Comply with the following: 1. NFPA: Provide electrical appliances listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application RESIDENTIAL APPLIANCES

2 C. Accessibility: Where residential appliances are indicated to comply with accessibility requirements, comply with the U.S. Architectural & Transportation Barriers Compliance Board's ADA-ABA Accessibility Guidelines. D. Owner and Architect to review appliance submittals prior to any purchase. PART 2 - PRODUCTS 2.1 MICROWAVE OVENS A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 1. General Electric Company (GE); JVM1740DP. 2. Sears Brands LLC (Kenmore); 3. Whirlpool Corporation; B. Microwave Oven (MW): 1. Basis-of-Design Product: General Electric Company (GE); JES2251SJ 2. Mounting: Countertop 3. Type: Conventional. 4. Capacity: 2.2 cu ft. 5. Oven Door: Door with observation window and pull handle. 6. Microwave Power Rating: 1200 W. 7. Electric Power Supply: 120 V, 60 Hz, 1 phase, 15 A. 8. Controls: Digital panel controls and timer display. 9. Other Features: Turntable. 10. Material: Porcelain-enameled steel. 11. Verify size and clearance prior to purchase 2.2 REFRIGERATOR/FREEZERS A. Basis-of-Design Product: Subject to compliance with requirements, provide General Electric Company (GE); GTS16GSHSS or comparable product by one of the following: 1. Sears Brands LLC (Kenmore). 2. Whirlpool Corporation. B. Refrigerator/Freezer (REFR.): Two-door refrigerator/freezer with freezer on top and complying with AHAM HRF Type: Freestanding. 2. Dimensions: a. Width: 28 inches (711 mm) nominal. b. Depth: inches nominal, minimum. c. Height: inches nominal RESIDENTIAL APPLIANCES

3 3. Storage Capacity: a. Refrigeration Compartment Volume: cu. ft. minimum. b. Freezer Volume: 3.98cu. ft. minimum. 4. Refrigerator Features: a. Interior light in refrigeration compartment. b. Temperature-controlled meat/deli bin. 5. Freezer Features: a. Automatic defrost. b. Automatic icemaker and storage bin. 6. Energy Performance, ENERGY STAR: Provide appliances that qualify for the EPA/DOE ENERGY STAR product labeling program. 7. Appliance Color/Finish: Stainless 8. Verify size and clearance prior to purchase. 2.3 UNDER-COUNTER REFRIGERATOR C. Basis-of-Design Product: Subject to compliance with requirements, provide Frigidaire FFPE4522QM or comparable product by one of the following: 1. Danby 2. Avanti D. Refrigerator- Single-door refrigerator 1. Type: Under-counter 2. Dimensions: a. Width: 21.5 inches nominal. b. Depth: inches nominal, minimum. c. Height: inches nominal. 3. Storage Capacity: a. Refrigeration Compartment Volume: 4.55 cu. ft. minimum. 4. Refrigerator Features: a. Interior light in refrigeration compartment. 5. Energy Performance, ENERGY STAR: Provide appliances that qualify for the EPA/DOE ENERGY STAR product labeling program RESIDENTIAL APPLIANCES

4 6. Appliance Color/Finish: White 7. Verify size and clearance prior to purchase. 8. Coordinate installation of counter-top with size of under-counter refrigerator, and provide a higher counter top if a counter top is shown on the drawings. 2.1 CLOTHES WASHER A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 1. General Electric Company (GE); GTW485ASJWS (Basis of Design). 2. Sears Brands LLC (Kenmore) 3. Whirlpool Corporation. B. Clothes Washer Complying with ASSE Basis-of-Design Product: General Electric Company (GE); GTW485ASJWS. 2. Type: Freestanding washer unit, top loading. 3. Dimensions: a. Width: 27 inches nominal. b. Depth: 27 inches nominal. c. Height: 44 inches nominal, minimum. 4. Washer: Manufacturer's standard. a. Washer Capacity: 4.2 cu. ft. minimum. 5. Washer Controls: Rotary-dial controls for water-fill levels, wash/rinse water temperatures, and variable-speed and fabric selectors. 6. Electric Washer: 120 V, 60 Hz, 1 phase, 15 A. 7. Motor: Manufacturer's standard with built-in overload protector. 8. Washing Features: a. Self-cleaning lint filter. b. Unbalanced-load compensator. c. Inlet Hoses: Minimum length 60 inches (1525 mm). d. Drain Hoses: Minimum length 48 inches (1220 mm). e. Self-leveling legs. f. Spin-cycle safety switch. 9. Verify size and clearance prior to purchase. 2.1 CLOTHES DRYER GAS FIRED A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 1510 RESIDENTIAL APPLIANCES

5 1. General Electric Company (GE); GTD45GASJWS (Basis of Design). 2. Sears Brands LLC (Kenmore) 3. Whirlpool Corporation. B. Clothes Dryer Complying with ASSE Basis-of-Design Product: General Electric Company (GE); GTW485ASJWS. 2. Type: Freestanding dryer unit, front loading. 3. Dimensions: a. Width: 27 inches nominal. b. Depth: 29.5 inches nominal. c. Height: 42.5 inches nominal, minimum. Dryer: Manufacturer's standard. d. Dryer Capacity: 7.2 cu. ft. minimum. 4. Dryer Controls: 4 temperature selections, Wrinkle free cycle, 4 cycles, air dry/air fluff cycle 5. Electric: 120 V, 60 Hz, 1 phase, 15 A. 6. Gas 7. Motor: Manufacturer's standard with built-in overload protector. 8. Dryer Features: a. Self-cleaning lint filter. b. Self-leveling legs. 9. Appliance Finish: Porcelain enamel on top and lid; baked enamel on front and sides. a. Color: White. 10. Appliance Finish: Porcelain enamel on top and lid; baked enamel on front and sides. a. Color: White. 11. Verify size and clearance prior to purchase. C. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping. D. Appearance of Finished Work: Noticeable variations in same piece are not acceptable. Variations in appearance of adjoining components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast RESIDENTIAL APPLIANCES

6 PART 3 - EXECUTION 3.1 EXAMINATION A. Examine substrates and conditions, with Installer present, for compliance with requirements for installation tolerances, power connections, and other conditions affecting installation and performance of residential appliances. B. Examine roughing-in for piping systems to verify actual locations of piping connections before appliance installation. C. Prepare written report, endorsed by Installer, listing conditions detrimental to performance of the Work. D. Proceed with installation only after unsatisfactory conditions have been corrected. 3.2 INSTALLATION, GENERAL A. General: Comply with manufacturer's written instructions. B. Built-in Equipment: Securely anchor units to supporting cabinets or countertops with concealed fasteners. Verify that clearances are adequate for proper functioning and that rough openings are completely concealed. C. Freestanding Equipment: Place units in final locations after finishes have been completed in each area. Verify that clearances are adequate to properly operate equipment. D. Range Anti-Tip Device: Install at each range according to manufacturer's written instructions. E. Utilities: Comply with plumbing and electrical requirements. F. Dryer venting: Provide complete dryer venting to exterior with weather & rodent proof wall cap. 3.3 DEMONSTRATION A. Engage a factory-authorized service representative to train Owner's maintenance personnel to adjust, operate, and maintain residential appliances. END OF SECTION RESIDENTIAL APPLIANCES