GREAT IN COOLING AND HEATING

Transcription

1 GREAT IN CHILLER COOLING AND HEATING APPLIED SYSTEMS CATALOGUE

2 02

3 Great in cooling and heating TABLE OF CONTENTS PRODUCT PORTFOLIO OPTIONS PORTFOLIO 08 ACCESSORIES PORTFOLIO 10 ENVIRONMENAL AWARENESS 12 HEAT RECOVERY 14 RELIABLE & EFFICIENT 16 AIR-COOLED 18 REMOTE EVAPORATOR 38 WATER-COOLED 40 REMOTE CONDENSER 46 HYDRAULIC MODULE 50 FAN COIL UNITS 52 MEASURING CONDITIONS 58

4

5 No matter how large your premises and whatever your air conditioning needs, there is a Daikin chilled water system to suit your requirements. It is a system that has proved its worth in a multiplicity of situations - from industrial sites to retail warehouses, hotels and department stores. The careful development of closely matched compressor/refrigerant combinations, has enabled Daikin to produce complete ranges of water chillers genuinely optimised for use with R-134a, R-407C and R-410A refrigerants. in their precision, power, low operating noise, easy maintenance and low running costs, Daikin chillers represent the sure and safe route to an indoor environment that is comfortable, clean and consistent. As a manufacturer that makes its own refrigerant and compressors, Daikin has total control at the production stage. It is this unique combination of advanced technology, experience and reliability that makes Daikin the obvious choice and long term solution for the professional. Daikin chillers offer the ultimate in flexibility and control a reflection of the advanced technology inherent within them. Unique

6 PRODUCT PORTFOLIO 06 A/C SCREW R-407C EWAP MBYNN EWTP MBYNN Type Compr. Refr. Mode Reference Packshot 0 17, R/E SCREW R-407C ERAP MBYNN W/C SCROLL R-407C SCREW R-134a EWWP KAW1N EWWP KAW1 EWWD MBYNN , R/C SCROLL R-407C EWLP012-65KAW1N 12, SCREW R-134a EWLD MBYNN

7

8 PORTFOLIO OPTIONS 08 Type Compr. Refr. Mode Reference Products Single pump contact Twin pump contact Single pump Integrated Hydronics Twin pump High ESP pump High ESP twin pump Buffer tank Reduced Noise Low noise Noise & Head Pressure Control Inverter fans Fan Silent Low Ambien A/C SWING SCROLL SCREW R-410A R-407C R-410A R-134A R-407C EWAQ-ACV3P EWYQ-ACV3P EUWAC-FZW EUWAN-KAZW EUWAP-KAZW EUWAB-KAZW EUWA-HZW EUWYN-KAZW EUWYP-KAZW EUWYB-KAZW EWAQ-DAYNN EWYQ-DAYNN EWAD-MBYNN EWAP-MBYNN EWTP-MBYNN R/E SCREW R-407C ERAP-MBYNN W/C EWWP-KAW1M SCROLL R-407C EWWP-KAW1N R/C SCREW R-134A EWWD-MBYNN SCROLL R-407C EWLP-KAW1N SCREW R-134A EWLD-MBYNN OPSC OPTC OPSP OPTP OPHP OPHT OPBT OPRN OPLN OPIF OPFS OPLA STD STD (3) (3) Option Combination & Exceptions: /A High efficiency unit /Q Standard efficiency unit, extra low noise /H High ambient unit /Z High efficiency unit, extra low noise A/C W/C C/F R/C R/E Air cooled Water cooled Centrifugal fan Remote condenser Remote evaporator cooling only heating only heat pump heat recovery (1) Unit length increase by 230mm (2) Unit length increase by 310mm (3) Not available with Option OPLN (4) High pressure side gauge (5) Not available with Option OPLN - OPRN

9 t High ESP fans Heat Recovery LWE Electrical Refrigerant Condenser Misc Total Heat Recovery Partial Heat Recovery High Glycol Low Glycol Evaporator heater Main switch Soft starter Power factor 0,9 A /V meter Address card No switchbox Electronic Expansion Valve Pressure Suction stop relief valve valve Gauges Coil guards Blank Cu /Al coils Cu / Sn coils Cu / Cu coils Cu / Ni heat exchanger Spring Anti Vibration Mounts 09 OPHF OPTR OPPR OPZH OPZL OP10 OP52 OPSS OPPF OP57 OPAC OPNS OPEX OP03 OP12 OPGA OPCG OPAL OPSN OPCU OPNI OPSVM STD STD STD STD STD STD STD STD

10 10 CHILLER Type Compr. Refr. Mode Reference SWING R-410A EWAQ ACV3P EWYQ ACV3P EUWAC5-8-10FZW EUWAN5-8KAZW EUWAN10-12KAZW EUWAN16KAZW EUWAN20-24KAZW EUWAP5-8KAZW EUWAP10-12KAZW EUWAP16KAZW EUWAP20-24KAZW EUWAB5-8KAZW EUWAB10-12KAZW EUWAB16KAZW EUWAB20-24KAZW R-407C EUWA30-35HZW SCROLL A/C EUWYN5-8KAZW EUWYN10-12KAZW EUWYN16KAZW EUWYN20-24KAZW EUWYP5-8KAZW EUWYP10-12KAZW EUWYP16KAZW EUWYP20-24KAZW EUWYB5-8KAZW EUWYB10-12KAZW EUWYB16KAZW EUWYB20-24KAZW R-410A EWAQ DAYNN EWYQ DAYNN R-134a EWAD MBYNN SCREW EWAP MBYNN R-407C EWTP MBYNN R/E SCREW R-407C ERAP MBYNN EWWP014KAW1N EWWP022KAW1N EWWP028KAW1N W/C SCROLL R-407C EWWP035KAW1N EWWP045KAW1N EWWP KAW1N EWWP KAW1M SCREW R-134a EWWD MBYNN EWLP012KAW1N EWLP020KAW1N EWLP026KAW1N R/C SCROLL R-407C EWLP030KAW1N EWLP040KAW1N EWLP KAW1N SCREW R-134a EWLD MBYNN EKGAU5/8KA EKGAU10/12KA Gauges EKGAU16KA EKGAU20/24KA EKGAU25/30H Soft starter EKSS EKAC10B EKAC30A Communication cards EKAC200A EKAC200J EKACPG EKACBAC EKACLON LON gateway EKLONPG EKBMSMBA M B * (2 pieces are needed) FAN COIL Type: FWM, FWL, FWV Description FWV FWL FWM Additional single row heat exchanger ESRH02A6 ESRH03A6 ESRH06A6 ESRH10A6 x x x Electric heater EEH01A6 EEH02A6 EEH03A6 EEH06A6 EEH10A6 x x x 2-pipe 3-way valve E2MV03A6 E2MV06A6 E2MV10A6 x x x 4-pipe 3-way valve E4MV03A6 E4MV06A6 E4MV10A6 x x x Fan stop thermostat YFSTA6 x x x Air intake & discharge grille EAIDF02A6 EAIDF03A6 EAIDF06A6 EAIDF10A6 - - x Supporting feet ESFV06A6 ESFV10A6 x - x Supporting feet + grille ESFVG02A6 ESFVG03A6 ESFVG06A6 ESFVG10A6 x - - Fresh air intake EFA02A6 EFA03A6 EFA06A6 EFA10A6 x x x Rear panel ERPV02A6 ERPV03A6 ERPV06A6 ERPV10A6 x x - Controller electromechanical ECFWMB6 x x - Controller electronic - built-in ECFWEB6 x x - Controller electronic - remote ECFWER6 x x x Master slave option EPIMSA6 x x x Vertical drainpan EDPVA6 x x x Horizontal drainpan EDPHA6 - x x

11 ACCESSORIES odbus gateway acnet gateway Remote user interface Buffer tanks Hydraulic module Low noise kit Switch box Common leaving water sensor Sequencing Panel Plant Visor Modem Converter RS485 to RS232 EKBMSBNA EKBNPG EKBMSBNJ EKRUMC EKRUPC EKRUPG EKRUPCJ EKRUPCK EKBT EKBT500N EKBTC10N EKBT500C EKBTC10C EHMC10A10 EHMC10A80 EHMC15A10 EHMC15A80 EHMC30A10 EHMC30A80 EKLS1 EKLS2 ECB1MUW ECB2MUW ECB3MUW EKCLWS EKCSCII EKPV2J EKMODEM EKGSMOD EKCON 11 Type: FWB-A Description Additional heat exchanger EAH04A6 EAH07A6 EAH10A6 3-way valve add. h/e E2MV307A6 E2MV310A6 2-way valve add. h/e E2MV207A6 E2MV210A6 Electric Heater Factory mounted Fan stop thermostat YFSTA6 Power interface - EPIB6 Master slave interface EPIMSA6 Controller electronic - remote ECFWER6 Type: FWD Description Electric heater: small Electric heater: big 2-pipe 3-way valve 4-pipe 3-way valve Vertical Drainpan Horizontal Drainpan Fan stop thermostat Fresh air intake Controller electronic - remote Power interface Master slave interface EDEH04A6 EDEHS06A6 EDEHS10A6 EDEHS12A6 EDEHS18A6 EDEH04A6 EDEHB06A6 EDEHB10A6 EDEHB12A6 EDEHB18A6 ED2MV04A6 ED2MV10A6 ED2MV12A6 ED2MV18A6 ED4MV04A6 ED4MV10A6 2xED2MV12A6 2 x ED2MV18A6 EDDPV10A6 EDDPV18A6 EDDPH10A6 EDDPH18A6 YFSTA6 EDMFA04A6 EDMFA06A6 EDMFA10A6 EDMFA12A6 EDMFA18A6 ECFWER6 - EPIB6 EPIMSA6 -

12 ENVIRONMENTAL AWARENESS 12 AIR CONDITIONING AND THE ENVIRONMENT Air conditioning systems provide a significant level of indoor comfort, making possible optimum working and living conditions in the most extreme climates. In recent years, motivated by a global awareness of the need to reduce the burdens on the environment, some manufacturers including Daikin have invested enormous efforts in limiting the negative effects associated with the production and the operation of air conditioners. Hence, models with energy saving features and improved eco-production techniques have seen the light of day, making a significant contribution to limiting the impact on the environment. SMART CONTROL BRINGS COMFORT AND REDUCES ENERGY CONSUMPTION Inverter technology used in the mini-chiller (EWAQ-AC and EWYQ-AC) and in the EWYD- AJYNN allows more precise control of the leaving water condition in function of the load. This leads to energy savings and high comfort levels, ensuring it is never too cool or too hot. This is a major advantage over standard fixed speed models, which use on/off cycling of the compressor, creating greater fluctuations in control conditions. Inverter technology offers improved levels of comfort: Energy efficient: Continuous matching of load requirement Start-up time is reduced by 1/3 Less frequent start/stop cycles Reduced sound pressure levels High EER/COP values

13 INVERTER TECHNOLOGY 13 Slow start Temperature remains stable Air conditioning with Inverter Air conditioning without Inverter

14 14 HEAT RECOVERY In many applications there often exists a simultaneous cooling and heating demand requirement alongside one another. To benefit from this Daikin offers the full range of R-407C EWTP MBYN chillers with heat recovery. This option further increases the application flexibility and extends possibilities in the hotel and leisure industry as well as the industrial and process sectors. By energetically recovering useful heat from the cooling cycle that would otherwise be rejected to outside COPs of up to 5.62 can be realized in heat recovery mode. The heat recovery unit aims to achieve an optimum balance between cooling and heat recovery to maximize the unit efficiency and offer savings in hot water production.

15 15 For full heat recovery both sensible and latent heat exchange will occur in the recovery exchanger. Inverter fans will be used to control the recovery outlet water temperature, by throttling back the airflow and maintaining the required condensing temperature. As a desuperheater the sensible heat from the hot discharge gas will be recovered, while the latent heat exchange will occur in the air-cooled condenser. The units efficiency is maintained as condensing pressure can be reduced due to air-cooled condenser becoming oversized. Hot water temperatures up to 70 C can be achieved. Condenser Condenser 45 C 60 C Full Recovery 85% of CC + PI 40 C Full Recovery (Desuperheater) 35% of CC + PI 50 C Comp Comp 7 C 12 C 7 C 12 C

16 RELIABLE AND EFFICIENT Whatever the requirements of the customer, large systems requiring constant capacity or smaller systems for flexibility, DAIKIN always provides a reliable and efficient solution. 3 COMPRESSOR TYPES FOR ALL APPLICATIONS: SWING COMPRESSOR: THE SCROLL COMPRESSOR FOR CONTROLLED CAPACITY: 16 swing Swing bush scroll Ref. Gas The piston which the blade and the roller unified The mini-chiller range is equipped with a swing compressor. This innovative design by Daikin with fewer moving parts allows smoother more reliable operation with low vibration and low noise levels. The high efficiency motor reduces energy consumption resulting in energy cost savings. Being compact, the DAIKIN scroll compressor is used with R-407C and R-410A to provide constant reliability and high efficiency right throughout its service life. Designed for small and medium capacities, the scroll compressors are used with air cooled and water cooled chillers within the range of capacities between 9.1 and 281kW. Characteristics : Compact, simple yet robust design Absence of valves and oscillating connecting mechanisms providing maximum reliability Constant compression guaranteeing low energy consumption Increased compression efficiency thanks to the absence of volumetric re-expansion Low sound level Low starting current

17 STANDARD ANTI-CORROSION TREATMENT As standard, condensers for air cooled chillers are given anticorrosion treatment. This treatment significantly increases resistance to acid rain and saline corrosion. Depending on the capacities and models, treatments are of the following type: Example of acrylic treatment Acrylic treatment (Daikin ref PE) The aluminium fins are coated with an acrylic resin and a hydrophilic film. Epoxy Treatment The aluminium fins are black epoxy coated. THE SINGLE SCREW STEPLESS COMPRESSOR - FOR HIGH CAPACITY: The heart of the larger Daikin chillers is a semi hermetic single screw compressor, designed, tested and manufactured in screw Casing 10 Slide valve Screw rotor Bearing Motor Gate rotor nd stage oil separator Demister (oil separator) Refrigerant suction 10. Refrigerant discharge 11. Compressor terminal + CTP 12. Stepper Motor 9 5 Daikin s own laboratories, in order to meet the highest capacity, performance and maintenance specifications. This compressor has been especially developed for operation with R-134a or R-407C refrigerant, guaranteeing unequalled reliability and many years of efficient operation. The bearing life is hrs with inspection and maintenance intervals every 40000hrs. Characteristics : Optimal performance through stepless capacity control in function of the chilled water temperature. The unit capacity is infinitely variable from % on single circuit units and % on dual circuit units. Compact, simple yet robust construction. Using a main single screw and two gate rotors, axial and radial forces are balanced thanks to the symmetrical compression guaranteeing low bearing loads. Renowned for its low noise levels the double walled casing design and integrated oil separator, add to the attenuation effect. Gate rotors made of polymer material result in closer tolerances with main screw and reduced friction greatly improving compressor efficiency and lifetime. No oil pump necessary lubrication based on differential pressure principle. Easy access to both compressor and safety devices Star delta starter with low starting current as standard 17

18 AIR-COOLED Air cooled chillers are most frequently used in the chilled water market. Out of its wide range of chillers in cooling only or heat pump version, with or without integrated hydronic components, DAIKIN always offers you a chiller fitting your application needs. 18 AIR-COOLED TABLE OF CONTENTS EWAQ-ACV3 20 EWYQ-ACV3 21 EUWAC-FZW 22 EUWA*-KAZW 24 EUWY*-KAZW 26 EWAQ-DAYN 28 EWYQ-DAYN 30 EWAD-MBYN 32 EWAP-MBYN 35 EWTP-MBYN 36

19 Daikin has taken great care to match major chiller components and refrigerant combinations to a point where high efficiency ranges of technically advanced and closely optimised air and water cooled units are now widely available for use with R-410A, R-407C and R-134a refrigerants. swing scroll screw 19 PIPING DIAGRAM FOR COMFORT COOLING APPLICATION AIR-COOLED Chillers EVAPORATOR Buffer Tank To fan coil units Expansion vessel Shut-off valve Filter Temperature sensor Pressure gauge (option) Pressure port Flow switch Drain valve Air purge 9. Safety valve 10. Pump 11. Water flow adjusting valve

20 EWAQ005AC STRENGTHS Optimised for use with R-410A. Inverter controlled swing compressor - Precise temperature control - No buffer tank required. PE treated condenser coil. Heating operation from -15 C to 43 C. Integrated hydronics - valves, filter, flow switch - 3 speed pump - 6l expansion vessel. Adaptive control possibility. OPTIONS (factory mounted) Evaporator heater tape. ELECTRONIC CONTROL CONTROL Leaving water control. Setpoint in heating & cooling. AVAILABLE INPUTS Voltage free contact: - ON/OFF. - Cooling/Heating changeover. Schedule timer: - ON/OFF. - Dual setpoint. - Silent operation. 20 EWAQ-ACV3 air-cooled swing swing EWAQ-ACV3 Cooling only Capacity Cooling kw Nominal input Cooling kw EER Dimensions (Height x Width x Depth) mm 805x1,190x360 Unit kg 100 Operating Weight kg 104 Type Brased plate Water Heat Exchanger Minimum water volume in the system l 10 Water flow rate Min l/min 12 Air heat exchanger Type Tube type l 6 Expansion vessel Volume bar 1 Sound Power Cooling dba Type Hermetically sealed swing compressor Compressor Model Quantity 1 Refrigerant type R-410A Refrigerant circuit Refrigerant charge kg 1.7 No of circuits 1 Refrigerant control Inverter Power Supply 1~/230V/50Hz Water heat exchanger inlet / outlet 1'' mbsp Piping connections Water heat exchanger drain hose nipple 1/2'' fbsp

21 EWYQ005AC STRENGTHS Optimised for use with R-410A. Inverter controlled swing compressor - Precise temperature control - No buffer tank required. PE treated condenser coil. Heating operation from -15 C to 43 C. Integrated hydronics - valves, filter, flow switch - 3 speed pump - 6l expansion vessel. Adaptive control possibility. OPTIONS (factory mounted) Evaporator heater tape. ELECTRONIC CONTROL CONTROL Leaving water control. Setpoint in heating & cooling. AVAILABLE INPUTS Voltage free contact: - ON/OFF. - Cooling/Heating changeover. Schedule timer: - ON/OFF. - Dual setpoint. - Silent operation. swing air-cooled EWYQ-ACV3 21 Heat Pump Capacity Cooling kw Heating kw Nominal input Cooling kw Heating kw EER COP Dimensions (Height x Width x Depth) mm 805x1190x360 Unit kg 100 Operating Weight kg 104 Type Brased plate Water Heat Exchanger Minimum water volume in the system l 10 Water flow rate Min l/min 12 Air heat exchanger Type Tube type l 6 Expansion vessel Volume bar 1 Sound Power Cooling dba Type Hermetically sealed swing compressor Compressor Model Quantity 1 Refrigerant type R-410A Refrigerant circuit Refrigerant charge kg 1.7 No of circuits 1 Refrigerant control Inverter Power Supply 1~/230V/50Hz Water heat exchanger inlet / outlet 1'' mbsp Piping connections Water heat exchanger drain hose nipple 1/2'' fbsp swing EWYQ-ACV3

22 22 EUWAC-FZW air-cooled scroll screw EUWAC-FZW STRENGTHS Daikin scroll compressor Standard reverse phase protection High fan static pressure (up to 150Pa) Operation down to -10 C ambient temperature Pressure gauges OPTIONS (factory mounted) Chilled water temperature down to - 5 C (ZH) or -10 C (ZL) ACCESSORIES (kit) Filter BMS gateway (MODBUS / J-BUS / BACNET protocol) Remote user interface Hydraulic module (see page 50) CONTROL Microprocessor control Water inlet temperature control

23 EUWAC8FZW AVAILABLE INPUTS / OUTPUTS Input ON / OFF (per circuit) Pump / flow switch Output Compressor operation Summary alarm Pump relay contact ELECTRONIC CONTROL 23 Cooling only Capacity Cooling kw Nominal input Cooling kw EER Capacity Steps % Dimensions (Height x Width x Depth) mm 1,345x856x630 1,290x1,180x630 1,395x1,330x630 Unit kg Operating Weight kg Type Brased plate, one per circuit Minimum water volume in the system l Water Heat Exchanger Min l/min Water flow rate Nominal l/min Max l/min Air heat exchanger Type Cross fin coil/hi-x tubes and PE coated waffle louvre fins Sound Power Cooling dba Type Hermetically sealed scroll compressor Compressor Model Quantity 1 Refrigerant type R-407C Refrigerant circuit Refrigerant charge kg No of circuits 1 Refrigerant control Thermostatic expansion valve Power Supply 3N~/400V/50Hz Piping connections Evaporator water inlet/outlet fbsp 1''field installation screw EUWAC-FZW

24 STRENGTHS Integrated hydraulic module (models B and P). Built-in buffer tank (model B). Daikin scroll compressor. Standard main isolator switch. Standard water flow switch. Standard filter (delivered as a kit with the unit). Operation down to -15 C ambient temperature. Standard reverse phase protection. Standard condenser protection grille. Freeze-up protection and prevention. PE treated condenser coil. 24 EUWA*-KAZW air-cooled scroll scroll EUWA*-KAZW OPTIONS (factory mounted) Chilled water temperature down to - 5 C (OPZH) or -10 C (OPZL). High ESP fans (50Pa) (OPHF). Pump size up (OPHP). ACCESSORIES (kit) Refrigerant pressure gauges. BMS gateway (MODBUS/ J-BUS/ BACNET protocol). Remote user interface. 200l buffer tank. Soft starter (single circuit). AVAILABLE INPUTS / OUTPUTS Input Remote ON/ OFF. Pump contact. Output Compressor operation. Summary alarm. Pump relay contact. HYDRAULIC AND REFRIGERANT DIAGRAM Air purge Safety valve CONTROL Microprocessor control. Water inlet temperature control. Buffer tank Water Pressure gauge Expansion vessel Drain Pressure port Flow switch Water flow adjusting valve Pump

25 EUWAN: Standard equipment Scroll compressor Main isolator switch Water flow switch Filter Condenser protection grille. All year operation EUWAN16KAZW EUWAP = EUWAN + Pump Expansion vessel Adjusting valve Drain Water pressure gauge Pressure relief valve. EUWAB = EUWAP + Buffer tank ELECTRONIC CONTROL 25 Cooling only N5 P5 B5 N8 P8 B8 N10 P10 B10 N12 P12 B12 N16 P16 B16 N20 P20 B20 N24 P24 B24 Capacity Cooling kw Nominal input Cooling kw EER Capacity Steps % Dimensions (Height x Width x Depth) mm 1,230x1,290x734 1,450x1,290x734 1,321x2,580x734 1,541x2,580x734 1,541x2,580x734 Unit kg Operating Weight kg Type Brased plate Minimum water volume in the system l Water Heat Exchanger Min l/min Water flow rate Nominal l/min Max l/min Air heat exchanger Type Cross fin coil/hi-x tubes and PE coated waffle louvre fins Buffer tank volume Volume l Sound Power Cooling dba Type Cross fin coil/hi-x tubes and PE coated waffle louvre fins Compressor Model Quantity 1 2 Refrigerant type R-407C Refrigerant circuit Refrigerant charge kg No of circuits 1 2 Refrigerant control Thermostatic expansion valve Power Supply 3N~/400V/50Hz Piping connections Evaporator water inlet/outlet 1-1/4''15 mm 2''15 mm scroll EUWA*-KAZW

26 STRENGTHS Integrated hydraulic module (models B and P) Built-in buffer tank (model B) Daikin scroll compressor Standard main isolator switch Standard water flow switch Standard filter (delivered as a kit with the unit) Operation down to -15 C ambient temperature Standard reverse phase protection Standard condenser protection grille Freeze-up protection and prevention PE treated condenser coil 26 EUWY*-KAZW air-cooled scroll scroll EUWY-KAZW OPTIONS (factory mounted) Chilled water temperature down to - 5 C (OPZH) or -10 C (OPZL) High ESP fans (50Pa) (OPHF) Pump size up (OPHP) ACCESSORIES (kit) Refrigerant pressure gauges. BMS gateway (MODBUS/ J-BUS/ BACNET protocol) Remote user interface 200l buffer tank Soft starter (single circuit) CONTROL AVAILABLE INPUTS / OUTPUTS Input Remote ON/ OFF Pump contact Remote cool/heat selection Output Compressor operation Summary alarm Pump relay contact Microprocessor control Water inlet temperature control

27 EUWYN: Standard equipment Scroll compressor Main isolator switch Water flow switch Filter Condenser protection grille. All year operation EUWYN16KAZW EUWYP = EUWYN + Pump Expansion vessel Adjusting valve Drain Water pressure gauge Pressure relief valve. EUWYB = EUWYP + Buffer tank ELECTRONIC CONTROL 27 Heat Pump N5 P5 B5 N8 P8 B8 N10 P10 B10 N12 P12 B12 N16 P16 B16 N20 P20 B20 N24 P24 B24 Capacity Nominal input Cooling kw Heating kw Cooling kw Heating kw EER COP Capacity Steps % Dimensions (Height x Width x Depth) mm 1,230x1,290x734 1,450x1,290x734 1,321x2,580x734 1,541x2,580x734 Unit kg Operating Weight kg Water Heat Exchanger Type Brased plate Minimum water volume in the system l Water flow rate Nominal Water pressure drop Min l/min Max l/min Cooling kpa Heating kpa Air heat exchanger Type Cross fin coil/hi-x tubes and PE coated waffle louvre fins Buffer tank volume Volume l Sound Power Cooling dba Compressor Refrigerant circuit Power Supply Type Hermetically sealed scroll compressor Model Quantity 1 2 Refrigerant type Refrigerant charge kg No of circuits 1 2 Refrigerant control R-407C Thermostatic expansion valve 3N~/400V/50Hz Piping connections Evaporator water inlet/outlet 1-1/4''15mm 2''15mm scroll EUWY-KAZW

28 STRENGTHS Wide capacity range: 80 to 260kW with 8 cooling only models R-410A refrigerant Multiple refrigerant circuits and multiple compressors per circuit Reliable and efficient scroll with high EER values Good part load efficiency (seasonal EER) Anti-corrosion treated aluminium coils Low operating noise levels Easy 'plug and play' installation Unit dimensions allow easy transport Fans protected against abnormal operation (4-8 fans depending on unit size) 28 EWAQ-DAYN air-cooled scroll scroll EWAQ-DAYN Safety valves in each circuit Electronic circuit breakers Electronic expansion valve True dual plate brazed plate heat exchanger Sight glass All hydronics can be accessed easily from 3 sides (no surrounding cabinet) Separate switchbox for easy access Compressors and controls at side of unit Increased reliability via 2 independent refrigerant circuits Dual circuit heat exchanger (from >100 kw) Non hermetic filter/dryer OPTIONS (factory mounted) Single pump contactor (OPSC) Twin pump contactor (OPTC) Single pump (OPSP) Twin pump (OPTP) (1 pump house, dual motor) High ESP pump (OPHP) (single pump only) Buffer tank (OPBT) Inverter fans (OPIF) (Not available with option OPLN) Glycol 0 C / -10 C (OPZL) Dual pressure relief valve (OP03) Evaporator heater tape (OP10) Option valves (discharge-, liquid line- and suction stop valve) A-meter / V-meter (OP57) Low Noise (OPLN) (=OPIF + compressor housing) Condenser protection grills (OPCG) New Daikin controller (Pcaso) with user friendly and powerful LCD interface

29 EWAQ DAYN ELECTRONIC CONTROL ACCESSORIES (kit) Gateway for LON (EKLONPG) Gateway for BACNET (EKBNPG) Address card (EKACPG) Remote user interface (EKRUPG) 29 Cooling only Capacity Cooling kw Nominal input Cooling kw EER Capacity Steps % /29-43/50/57-71/ /28-40/50/56-72/ Dimensions (Height x Width x Depth) mm 2,311x2,000x2,566 2,311x2,000x2,631 2,311x2,000x3,081 2,311x2,000x4,850 Unit kg 1,350 1,400 1,500 1,550 1,800 1,850 3,150 3,250 Operating Weight kg 1,315 1,415 1,517 1,569 1,825 1,877 3,189 3,292 Water Heat Exchanger Type Brased plate Minimum water volume in the system l Water flow rate Nominal Water pressure drop Min l/min Max l/min ,043 1,198 1,355 1,456 Cooling kpa Air heat exchanger Type Cross fin coil / Hi-Xss tubes and PE coated Sound Power Cooling dba Compressor Refrigerant circuit Power Supply Piping connections Type Scroll compressor Model Quantity 2 4 Refrigerant type Refrigerant charge kg R-410A No of circuits 1 2 Refrigerant control Electronic expansion valve 3~/400V/50Hz Water heat exchanger inlet / outlet 3"od 3" Water heat exchanger drain 1/2"g scroll EWAQ-DAYN

30 STRENGTHS Wide capacity range: 80 to 250kW with 8 heat pump models R-410A refrigerant Multiple refrigerant circuits and multiple compressors per circuit Reliable and efficient scroll with high EER values Good part load efficiency (seasonal EER) Anti-corrosion treated aluminium coils Low operating noise levels Easy 'plug and play' installation Unit dimensions allow easy transport Fans protected against abnormal operation (4-8 fans depending on unit size) 30 EWYQ-DAYN air-cooled scroll scroll EWYQ-DAYN Safety valves in each circuit Electronic circuit breakers Electronic expansion valve True dual plate brazed plate heat exchanger Sight glass All hydronics can be accessed easily from 3 sides (no surrounding cabinet) Separate switchbox for easy access Compressors and controls at side of unit Increased reliability via 2 independent refrigerant circuits Dual circuit heat exchanger (from >100 kw) Non hermetic filter/dryer New Daikin controller (Pcaso) with user OPTIONS (factory mounted) Single pump contactor (OPSC) Twin pump contactor (OPTC) Single pump (OPSP) Twin pump (OPTP) (1 pump house, dual motor) High ESP pump (OPHP) (single pump only) Buffer tank (OPBT) Inverter fans (OPIF) (Not available with option OPLN) Glycol 0 C / -10 C (OPZL) Dual pressure relief valve (OP03) Evaporator heater tape (OP10) Option valves (discharge-, liquid line- and suction stop valve) A-meter / V-meter (OP57) Low Noise (OPLN) (=OPIF + compressor housing) Condenser protection grills (OPCG) friendly and powerful LCD interface

31 EWYQ DAYN ELECTRONIC CONTROL ACCESSORIES (kit) Gateway for LON (EKLONPG) Gateway for BACNET (EKBNPG) Address card (EKACPG) Remote user interface (EKRUPG) 31 Heat Pump Capacity Nominal input Cooling kw Heating kw Cooling kw Heating kw EER COP Capacity Steps % /29-43/50/57-71/ /28-44/50/56-72/ Dimensions (Height x Width x Depth) mm 2,311x2,000x2,566 2,311x2,000x2,631 2,311x2,000x3,081 2,311x2,000x4,850 Unit kg 1,400 1,450 1,550 1,600 1,850 1,900 3,200 3,300 Operating Weight kg 1,415 1,465 1,567 1,619 1,875 1,927 3,239 3,342 Water Heat Exchanger Type Brased plate Minimum water volume in the system l Water flow rate Nominal Water pressure drop Min l/min Max l/min ,141 1,290 1,479 1,611 Cooling / Heating kpa 36 /47 36 /47 43 / / / / / / 46 Air heat exchanger Type Cross fin coil / Hi-Xss tubes and PE coated Sound Power Cooling dba Compressor Refrigerant circuit Power Supply Piping connections Type Scroll compressor Model Quantity 2 4 Refrigerant type Refrigerant charge kg R-410A No of circuits 1 2 Refrigerant control Electronic expansion valve 3~/400V/50Hz Water heat exchanger inlet / outlet 3"od 3" Water heat exchanger drain 1/2"g scroll EWYQ-DAYN

32 32 EWAD-MBYN air-cooled scre w screw EWAD-MBYN STRENGTHS DAIKIN stepless single screw compressor Operation down to -15 C ambient temperature Standard reverse phase protection Freeze-up protection and prevention PE treated condenser coil VICTAULIC joints Standard discharge shut-off valve DICN operation as standard within same series Flow switch Modular design High energy efficiency ratio OPTIONS (factory mounted) Main isolator switch Condenser protection grilles Low noise (-5 to -7dB(A)) Compressor suction stop valve Ampere & Voltmeter (read-out on switchbox) Chilled water temperature down to - 5 C (ZH) or -10 C (ZL) Hi-ESP fans Dual pressure relief valve ACCESSORIES (kit) Leaving water control sensor for DICN BMS gateway. (MODBUS/J-BUS/BACNET protocol) Remote user interface (EKRUPC)

33 EWAD170MBYNN CONTROL Microprocessor control Water inlet or outlet temperature control Leaving water control sensor for DICN AVAILABLE INPUTS / OUTPUTS Input ON / OFF (per circuit) Dual setpoint Pump / flow switch Output Compressor operation Summary alarm (per circuit) Pump relay contact ELECTRONIC CONTROL 33 Cooling only Capacity kw Nominal input Cooling kw EER Capacity Steps % Dimensions (Height x Width x Depth) mm 2,221x3,973x1,109 2,250x4,280x2,238 2,250x5,901x2,238 Unit kg 1,391 1,600 1,705 2,710 3,210 3,260 5,335 5,595 5,775 5,855 Operating Weight kg 1,441 1,663 1,768 2,790 3,340 3,390 5,497 5,779 5,959 6,039 Water Heat Exchanger Type Shell and tube Minimum water volume in the system l ,100 1,280 1,480 Water flow rate Nominal Water pressure drop Min l/min Max l/min ,165 1,580 1,880 Cooling kpa Air heat exchanger Type Cross fin coil/hi-x tubes and PE coated waffle louvre fins Sound Power Cooling dba Compressor Refrigerant circuit Power Supply Piping connections Type Semi-hermetic single screw compressor Model Quantity 1 2 Refrigerant type Refrigerant charge kg R-134a No of circuits 1 2 Refrigerant control Thermostatic expansion valve Electronic expansion valve Evaporator water inlet/outlet 3'' vc 1/2'' g-f uni-iso 228/1 4'' victaulic coupling 1/2'' g-f uni-iso 228/1 3~/400V/50Hz 5'' victaulic coupling 1/2'' g-f uni-iso 228/1 6'' victaulic coupling 1/2'' g-f uni-iso 228/1 screw EWAD-MBYN

34 34

35 EWAP200MBYN STRENGTHS DAIKIN stepless single screw compressor Operation down to -15 C ambient temperature Standard reverse phase protection Freeze-up protection and prevention PE treated condenser coil VICTAULIC joints and filter as standard DICN operation as standard within same series Chilled water temperature down to 5 C(ZH) or -10 C(ZL) (user setting) Standard discharge shut-off valve Standard flow switch Modular design OPTIONS (factory mounted) dual pressure relief valve on the condenser. Main isolator switch. Condenser protection grilles. Low noise (-5 to -7dB(A)). Compressor suction stop valve Ampere & Voltmeter (read-out on switchbox). Hi-ESP fans. Inverter fans. Heat Recovery (see also p. 36) ACCESSORIES (kit) leaving water control sensor for DICN. BMS card. BMS gateway (MODBUS/J-BUS/ BACNET protocol). Remote user interface (EKPUPC). CONTROL Microprocessor control. Water inlet or outlet temperature control Weekly operating schedule. AVAILABLE INPUTS / OUTPUTS Input ON / OFF (per circuit). Dual setpoint through analog signal. Floating setpoint. Pump / flow switch. Output Compressor operation. Summary alarm (per circuit). Pump relay contact. ELECTRONIC CONTROL scre w air-cooled EWAP-MBYN 35 Cooling only Capacity Cooling kw Nominal input Cooling kw EER Capacity Steps % Dimensions (Height x Width x Depth) mm 2250x2346x x4280x x5901x2238 Unit kg Operating Weight kg Water Heat Exchanger Type Brased plate, one per circuit Minimum water volume in the system l Water flow rate Nominal Water pressure drop Min l/min Max l/min Cooling kpa Air heat exchanger Type Cross fin coil/hi-x tubes and PE coated waffle louvre fins Sound Power Cooling dba Compressor Refrigerant circuit Power Supply Piping connections Type Semi-hermetic single screw compressor Model Quantity 1 Refrigerant type Refrigerant charge kg No of circuits 1 2 Refrigerant control Evaporator water inlet/outlet flexible coupling + counterpipe for welding 3''odfield installation flexible coupling + counterpipe for welding 3''od1/4''g R-407C Thermostatic expansion valve 3~/400V/50Hz flexible coupling + counterpipe for welding 3''1/4''g flexible coupling + counterpipe for welding 5''1/4''g screw EWAP-MBYN Relief device outlet compressor: 1''npt compressor: 2x1''npt compressor: 2x(1''npt) compressor: 1x(1''npt) +1x(2x1''npt) compressor: 2x(2x1''npt)

36 36 EWTP-MBYN BASED ON EWAP-MBYN heat recovery scre w screw EWTP-MBYN Total heat recovery up to 85% or desuperheater up to 60 C leaving water temperature Standard Inverter fans and exchanger heatertape Daikin semi-hermetic single screw stepless compressor Optimised for use with R-407C Advanced pco2 DDC controller DICN (Daikin Integrated Chiller Network) operation as standard within same series Pressure relief valve Reduced energy consumption thanks to optimised condensing temperature by use of inverter fans Inverter fans ensure smoother operation and better colour of sound Linear sound reduction in function of ambient temperature Optional BMS connection available Evaporator heater tape as standard on all units Multiple capacity steps Pre-mounted, 5 inch piping for easier field connection Modular design Double refrigeration circuit (from 400kW on) Standard operation range down to -15 C ambient Victaulic joints and filter as standard Moisture indicator as standard High quality, anti-corrosion treated components as standard Chilled water temperatures down to -10 C on standard unit

37 EWTP-MBYN ELECTRONIC CONTROL 37 Heat recovery Capacity Nominal input Cooling kw Cooling during heat recovery kw Heat recovery kw Cooling kw Heat recovery kw EER COP Capacity Steps % (stepless) (stepless) Dimensions (Height x Width x Depth) mm 2250x2346x x4280x x5901x2238 Unit kg Operating Weight kg Water Heat Exchanger Type Brased plate, one per circuit Minimum water volume in the system l Water flow rate Min l/min Max l/min Air heat exchanger Type Cross fin coil/hi-x tubes and chromate coated waffle louvre fins Sound Power Cooling dba Compressor Refrigerant circuit Power Supply Piping connections Type Semi-hermetic single screw compressor Model Quantity 1 Refrigerant type Refrigerant charge kg No of circuits 1 2 Refrigerant control Evaporator water inlet/outlet Heat recovery condenser inlet/outlet flexible coupling + counterpipe for welding 3'' od field installation R-407C Thermostatic expansion valve 3~/400V/50Hz flexible coupling + counterpipe for welding 3''1/4''g 2''g flexible coupling 5''1/4''g screw EWTP-MBYN

38 REMOTE EVAPORATOR The Daikin ERAP condensing units can be used in a wide variety of air conditioning, refrigeration and ventilation applications. 38 REMOTE EVAPORATOR TABLE OF CONTENTS ERAP-MBYNN 39 PIPING DIAGRAM FOR COMFORT COOLING APPLICATION Chiller Air handling unit Switchbox Thermistor line

39 ERAP150MBYNN STRENGTHS DAIKIN stepless single screw compressor. Operation down to -15 C ambient temperature. Standard reverse phase protection. Freeze-up protection and prevention. PE treated condenser coil. Liquid stop valve. Discharge stop valve. Standard suction stop valve. OPTIONS (factory mounted) Main isolator switch. Condenser protection grilles. Low noise (down to -6dB(A)). Ampere & Voltmeter (read-out on switchbox). Hi-ESP fans. ACCESSORIES (kit) BMS gateway (MODBUS/J-BUS/ BACNET protocol). Remote user interface. CONTROL Return air or room temperature control. Weekly operating schedule. AVAILABLE INPUTS / OUTPUTS Input ON / OFF. Dual setpoint through analog signal. Air flow switch. Capacity limit. Output Compressor operation. Summary alarm. ELECTRONIC CONTROL scre w remote evaporator ERAP-MBYN 39 Cooling only Capacity Cooling kw Nominal input Cooling kw EER Capacity Steps % Dimensions (Height x Width x Depth) mm 2250x2346x2238 Unit kg Air heat exchanger Type Cross fin coil/hi-x tubes and PE coated waffle louvre fins Sound Power Cooling dba Type Semi-hermetic single screw compressor Compressor Model Quantity 1 Refrigerant type R-407C Refrigerant circuit Refrigerant charge kg No of circuits 1 Power Supply 3~/400V/50Hz Suction line connection 2'' 1/8 Piping connections Liquid line connection 7/8'' Relief device outlet compressor: 1''npt screw ERAP-MBYN

40 WATER-COOLED Daikin offers you compact water-cooled chiller units which require only very limited space in a machine room. Used for commercial or industrial applications, these chillers generate cold and hot water, which can be used for chilling, heating, or even both at the same time. 40 WATER-COOLED TABLE OF CONTENTS EWWP-KAW1N 42 EWWD-MBYN 44

41 Balancing valve Pressure gauge Temperature sensor Drain valve Shut-off valve Fill valve Filter Drain Safety valve 10. Pressure port 11. Pump 12. Flow switch 13. Pressure regulating valve 14. Bypass valve 41 PIPING DIAGRAM FOR COMFORT COOLING APPLICATION WATER-COOLED To fan coil units Expansion vessel Chillers Expansion vessel Buffer tank Condenser Evaporator Buffer tank To fan coil units

42 STRENGTHS One of the most compact units in the market (60cm x 60cm x 60cm for models 014 to 035). Daikin scroll compressor. Standard reverse phase protection. Extension possible up to 195kW. FOR SINGLE MODULE UNITS Standard main isolator switch. Basic hydraulic components for KA-series included with the unit as a kit: flow switch, air purge, filter + shut-off valves for both condenser and evaporator. OPTIONS (factory mounted) Chilled water temperature down to - 5 C (OPZH) or -10 C (OPZL). ACCESSORIES (kit) Compressor soundproof material (-3dBA). Hydraulic module (see page 50). BMS gateway (MODBUS/J-BUS / BACNET protocol). Remote user interface. CONTROL Microprocessor control. Water inlet temperature control. Cold water or hot water regulation. AVAILABLE INPUTS / OUTPUTS Input Remote ON / OFF. Pump contact. Cool/heat selection. Output Compressor operation. Summary alarm. Pump relay contact. ELECTRONIC CONTROL 42 EWWP-KAW1N water-cooled scroll scroll EWWP-KAW1N Cooling only/heating only Capacity Cooling kw Nominal input Cooling kw EER Capacity Steps % Dimensions (Height x Width x Depth) mm 600x600x x600x x600x x600x1200 Unit kg Type Brased plate Minimum water volume in the system l Water Heat Exchanger Min l/min Water flow rate Nominal l/min Max l/min Sound Power Cooling dba Type Hermetically sealed scroll compressor Compressor Model Quantity Refrigerant type R-407C Refrigerant circuit Refrigerant charge kg No of circuits Refrigerant control Thermostatic expansion valve Power Supply 3N~/400V/50Hz Evaporator water inlet/outlet fbsp 25 field installation fbsp 40 field installation 2 x 2 x fbsp 38 field installation 3 x 2 x fbsp 38 field installation Piping connections Condenser water inlet/outlet fbsp 25 field installation fbsp 40 field installation 2 x 2 x fbsp 38 field installation 3 x 2 x fbsp 38 field installation

43 EWWP KAW1N EWWP KAW1N EWWP KAW1N 43 SELECTION TABLE 1 MODULE (KA-series) 2 MODULES (KA-series) 3 MODULES (KA-series) Capacity index Cooling capacity (kw) Heating capacity (kw) UNIT + CONTROL (factory mounted) UNIT ONLY (Without Control) CONTROL (Kit) EWWP014KAW1N EWWP022KAW1N EWWP028KAW1N EWWP035KAW1N EWWP045KAW1N EWWP055KAW1N EWWP065KAW1N EWWP045KAW1M EWWP055KAW1M EWWP065KAW1M ECB 1 MUW ECB 2 MUW ECB 3 MUW screw EUWAC-FZW For example: for a 121 kw -HP system, select : EWWP055KAW1 + EWWP065KAW1

44 44 EWWD-MBYN water-cooled scre w screw EWWD-MBYN STRENGTHS Compact and modular design. DAIKIN stepless single screw compressor. Standard reverse phase protection. VICTAULIC joints. DICN operation as standard within same series. Standard discharge shut-off valve. Standard filter, flow switch. ACCESSORIES (kit) BMS gateway (MODBUS/J-BUS / BACNET protocol). Remote user interface (EKRUPC). CONTROL Microprocessor control. Water inlet or outlet temperature control. Weekly operating schedule. OPTION (factory mounted) Main isolator switch. Low noise (-5 to -7dB(A)). Compressor suction stopvalve. Ampere & Voltmeter (read-out on switchbox). Chilled water temperature down to - 5 C (ZH) or -10 C (ZL). Dual pressure relief valve.

45 EWWD120MBYN AVAILABLE INPUTS / OUTPUTS Input ON / OFF. Pump contact. Dual setpoint through analog signal. Floating setpoint. Output Compressor operation. Summary alarm (per circuit). Pump relay contact. ELECTRONIC CONTROL 45 Cooling only/heating only Capacity Nominal input Cooling kw Heating kw Cooling kw Heating kw EER COP Capacity Steps % stepless stepless Dimensions (Height x Width x Depth) mm 1018x2681 (3051)x x2681 (3254)x x2681 (3254)x930 Unit kg Operating Weight kg Water Heat Exchanger Type Shell and tube Minimum water volume in the system l Water flow rate Min l/min Nominal l/min Max l/min Pressure Cooling dba Compressor Refrigerant circuit Power Supply Piping connections Type Semi-hermetic single screw compressor Model Quantity Refrigerant type Refrigerant charge kg No of circuits 1 2 Refrigerant control Thermostatic expansion valve Electronic expansion valve Evaporator water inlet/outlet Condensor water inlet/outlet 3" od vc field installation 2'' 1/2 victaulic m6 R-134a Thermostatic expansion valve 3~/400V/50Hz 3" victaulic coupling field installation 3'' victaulic m6 Electronic expansion valve Relief device outlet 1x1'' 2x1'' 3x1'' 4x1'' screw EWWD-MBYN

46 REMOTE CONDENSER Daikin offers you flexible and compact chillers with remote condenser, which can be used to satisfy applications with special requirements in the field of available space, sound level or extreme operating conditions. In these exceptional cases, remote condenser solutions can be preferred over standard air-cooled or water-cooled solutions. 46 WATER-COOLED TABLE OF CONTENTS EWLP-KAW1N 48 EWLD-MBYN 49

47 Temperature sensor Filter Shut-off valve Pump Pressure port Flow switch Drain Pressure gauge Water flow adjusting valve 10. Drain valve 11. Fill valve 12. Safety valve 47 PIPING DIAGRAM FOR COMFORT COOLING APPLICATION WATER-COOLED Gas Chillers Expansion vessel To condenser Liquid Evaporator Buffer tank To fan coil units Expansion vessel

48 EWLP014KAW1N STRENGTHS One of the most compact units in the market (60cm x 60cm x 60cm for models 012 to 030). Daikin scroll compressor. Standard main isolator switch. Basic hydraulic components : included as a kit with the unit: flow switch, air purge, filter + shut-off valves. Standard reverse phase protection. OPTIONS (factory mounted) Chilled water temperature down to - 5 C (ZH) or -10 C (ZL). ACCESSORIES (kit) Compressor soundproof material (-3dBA). Hydraulic module (see page 50). BMS gateway (MODBUS/J-BUS / BACNET protocol). Remote user interface. CONTROL Microprocessor control. Water inlet temperature control. AVAILABLE INPUTS / OUTPUTS Input Remote ON / OFF. Pump contact. Output Compressor operation. Summary alarm Pump relay contact. ELECTRONIC CONTROL 48 EWLP-KAW1N water-cooled scroll scroll EWLP-KAW1N Cooling only Capacity Cooling kw Nominal input Cooling kw EER Capacity Steps % 1 2 Dimensions (Height x Width x Depth) mm 600x600x x600x1200 Unit kg Type Brased plate Minimum water volume in the system l Water Heat Exchanger Min l/min Water flow rate Nominal l/min Max l/min Sound Power Cooling dba Type Hermetically sealed scroll compressor Compressor Model Quantity 1 2 Refrigerant type R-407C Refrigerant circuit No of circuits 1 2 Refrigerant control Thermostatic expansion valve Power Supply 3N~/400V/50Hz Evaporator water inlet/outlet fbsp 25field installation fbsp 40field installation Piping connections Liquid line connection 9.52 flare 12.7 flare 2x12.7 flare Discharge line connection 12.7 flare 19.1 flare 2x19.1 flare

49 EWLD120MBYN ELECTRONIC CONTROL STRENGTHS DAIKIN stepless single screw compressor. Compact and modular design. Standard phase sequence controller. VICTAULIC joints. DICN operation as standard within same series. Standard discharge shut-off valve. Standard flow switch. Standard filter. OPTIONS (factory mounted) Main isolator switch. Low noise (-6dB(A)). Compressor suction stop valve. Ampere and Voltmeter (read-out on switchbox). Chilled water temperature down to - 5 C (ZH) or -10 C (ZL). Dual pressure relief valve ACCESSORIES (kit) BMS gateway (MODBUS / J-BUS / BACNET protocol). Remote user interface. CONTROL Microprocessor control. Water inlet temperature control. Weekly operation schedule. AVAILABLE INPUTS / OUTPUTS Input ON / OFF. Pump contact. Dual setpoint through analog signal. Floating set point. Output Compressor operation. Summary alarm. Fan-condenser relay contacts. Pump relay contact scre w EWLD-MBYN 49 Cooling only Capacity Cooling kw Nominal input Cooling kw EER Capacity Steps % stepless stepless Dimensions (Height x Width x Depth) mm 1018x2681 (3051)x x2681 (3254)x x2681 (3254)x930 Unit kg Operating Weight kg Water Heat Exchanger Type Brased plate, one per circuit Minimum water volume in the system l Water flow rate Min l/min Nominal l/min Max l/min Sound Power Cooling dba Compressor Refrigerant circuit Power Supply Piping connections Type Semi-hermetic single screw compressor Model Quantity Refrigerant type No of circuits 1 2 Refrigerant control Thermostatic expansion valve Electronic expansion valve Evaporator water inlet/outlet 3'' od vc field installation R-134a Thermostatic expansion valve 3~/400V/50Hz 3'' victaulic coupling field installation Electronic expansion valve Liquid line connection 7/8'' 1'' 1/8 1'' 3/8 2x1/8'' 1''1/8 + 1''3/8 2x1'' 3/8 Discharge line connection 2'' 1/8 2'' 5/8 2x(2''1/8) 2'' 1/8 + 2'' 5/8 2x(2''5/8) screw EWLD-MBYN

50 EHMC15AV1010 mh 2 O PUMP CHARACTERISTICS LEGENDS Pump characteristics 1. EHMC30AV EHMC10AV1080 & EHMC15AV EHMC30AV EHMC10AV1010 & EHMC15AV1010 STRENGTHS 100l buffer tank. Freeze-up protection (heater tape). Single pump. 12l expansion vessel. Standard dual pressure ports WF (l/min) Water flow Hydraulic module + filter pressures losses 1.EHMC15/30AV1010 & EHMC15/30AV EHMC10AV1010 & EHMC10AV EHMC-AV Hydraulic Module HYDRONIC KITS hydronic kits Nominal flow l/min Nominal static height mh2o Nominal input W 630 1, ,070 1,070 2,090 Dimensions (HxWxD) mm 1,284x635x688 1,284x635x688 1,284x635x688 Machine weight kg Sound power dba Sond pressure dba Power supply V1 230V/1~/50Hz Operation range Water side CDB -10 C ~ 55 C Air side CDB -10 C ~ 43 C Evaporator water inlet/outlet 1 BSPF 2 BSPF 2-1/2 BSPF Piping connections Drain connection 1/2 EKBT Buffer Tank EKBT 200l Buffer tank with casing EKBT500N 500l Buffer tank EKBTC l Buffer tank EKBT500C 500l Buffer tank with casing EKBTC10C 1000l Buffer tank with casing

51 51

52 FAN COIL UNITS Fan Coil Units are a highly efficient means of turning a water chiller, heat pump or hot water boiler into an efficient, quiet air conditioning system. These units are an effective solution to provide a comfortable environment for both commercial and residential applications. 52 DAIKIN offers a wide range of Fan Coil Units for both concealed and exposed applications. 3 models are available in flexible application. The only moving part in the units is the fan, which making them ideal for use in offices, hotels and at home. The goal is to obtain the right solution, both technically and aesthetically. TABLE OF CONTENTS 53 FWV 54 FWL 55 FWM 56 FWB 57 FWD

53 ECFWER6 ECFWEB6 FWV02CAT Quick fixing system for wall mounting Pre-assembled 3-way/4-port ON/OFF valves are available Valve packages are insulated, no extra drain pan required Valve packages contain balancing valves and sensor pocket Fast-on connections for electrical options : no tools needed Quick removal of washable filter Electrical heater : no relay up to 2kW capacity Electrical heater : equipped with two overheat cut-out thermostats floor standing unit FWV 53 FWV01-10C* 2-pipe (*=TN or TV) 4-pipe (*=FN or FV) Power input W Capacity Total capacity kw Cooling capacity Sensible capacity kw Heating capacity (2-pipe) kw Heating capacity (4-pipe) kw Dimensions H xw x D mm 564x774x x984x x1194x x1404x x774x x984 x x1194x226 Machine weight kg x1404x251 Sound level Sound power dba Water pressure drop Cooling kpa Heating kpa Fan Air flow rate m³/h Water connections Std. heat exchanger inch 1/2 3/4 1/2 3/4 Required power supply V / f / Hz 230/1/50 Water flow Cooling l/h ,154 1, ,142 1,355 Heating l/h ,154 1, Coil Water volume heating l Maximum absorbed current W fan coils FWV * : TN (2-pipe, without valves) - TV (2-pipe, with ON/OFF 3-way valves) - FN (4-pipe, without valves) - FV (4-pipe, with ON/OFF 3-way valves)

54 ECFWER6 ECFWEB6 FWL03C FWL03C Quick fixing system for wall/ceiling mounting Pre-assembled 3-way/4-port ON/OFF valves are available Valve packages are insulated, no extra drain pan required Valve packages contain balancing valves and sensor pocket Fast-on connections for electrical options : no tools needed Quick removal of washable filter Electrical heater : no relay up to 2kW capacity Electrical heater : equipped with two overheat cut-out thermostats 54 FWL flexi type unit fan coils FWL FWL01-10C* 2-pipe (*=TN or TV) 4-pipe (*=FN or FV) Power input W Capacity Cooling capacity Total capacity kw Sensible capacity kw Heating capacity (2-pipe) kw Heating capacity (4-pipe) kw Dimensions H xw x D mm 564x774x x984 x x1194x x1404x x774x x984 x x1194x226 Machine weight kg x1404x251 Sound level Sound power dba Water pressure drop Cooling kpa Heating kpa Fan Air flow rate m³/h Water connections Std. heat exchanger inch 1/2 3/4 1/2 3/4 Required power supply V / f / Hz 230/1/50 Water flow Cooling l/h ,154 1, ,142 1,355 Heating l/h ,154 1, Coil Water volume heating l Maximum absorbed current W * : TN (2-pipe, without valves) - TV (2-pipe, with ON/OFF 3-way valves) - FN (4-pipe, without valves) - FV (4-pipe, with ON/OFF 3-way valves)

55 ECFWER6 FWM01C FWM01C Quick fixing system for wall/ceiling mounting Pre-assembled 3-way/4-port ON/OFF valves are available Valve packages are insulated, no extra drain pan required Valve packages contain balancing valves and sensor pocket Fast-on connections for electrical options : no tools needed Quick removal of washable filter Electrical heater : no relay up to 2kW capacity Electrical heater : equipped with two overheat cut-out thermostats flexi type unit FWM FWM01-10C* 2-pipe (*=TN or TV) 4-pipe (*=FN or FV) Power input W Total capacity kw Cooling capacity Sensible capacity kw Capacity Heating capacity (2-pipe) kw Heating capacity (4-pipe) kw Dimensions H xw x D mm 535x584x x794x x1004x x1214x x584x x794x x1004x x1214x249 Machine weight kg Sound level Sound power dba Cooling kpa Water pressure drop Heating kpa Fan Air flow rate m³/h Water connections Std. heat exchanger inch 1/2 3/4 1/2 3/4 Required power supply V / f / Hz 230/1/50 Cooling l/h ,154 1, ,142 1,355 Water flow Heating l/h ,154 1, Coil Water volume heating l Maximum absorbed current W fan coils FWM * : TN (2-pipe, without valves) - TV (2-pipe, with ON/OFF 3-way valves) - FN (4-pipe, without valves) - FV (4-pipe, with ON/OFF 3-way valves)

56 ECFWER6 FWB04AAT Height of the units only 240mm for all the sizes 3, 4 or 6 stage row cooling coil Drain pan to collect the condensate from: heat exchanger and regulating valves 7-speed electrical motors (with thermal protection on windings) All 7 speeds pre-wired in the factory in the terminal block of the switch box Standard air filter : removable from the bottom 56 FWB concealed ceiling unit fan coils FWB FWB02-10AT 2-pipe Power input W Total capacity kw Cooling capacity Sensible capacity kw Capacity Heating capacity (2-pipe) kw Heating capacity (4-pipe)* kw Dimensions H xw x D mm 239x1039x x1389x x1739x609 Machine weight kg Sound level Sound power dba Water pressure drop Cooling kpa Heating kpa Fan Air flow rateww m³/h Available pressure Pa Water connections Std. heat exchanger inch 3/4 Required power supply V / f / Hz 230/1/50 Water flow Cooling l/h ,111 1,299 1,488 1,774 Heating l/h ,123 Maximum absorbed current W * : 4-pipe = 2-pipe + option Additional heat exchanger

57 ECFWER6 FWD04A FWD04A Quick fixing system for wall/ceiling mounting Straight duct connector is mounted to discharge side Standard air filter : removable from the bottom flexi type unit FWD 57 FWD04-18A* 2-pipe (*=T) 4-pipe (*F) Power input W Total capacity kw Cooling capacity Sensible capacity kw Capacity Heating capacity (2-pipe) kw Heating capacity (4-pipe) kw fan coils FWD Dimensions H xw x D mm 280 x754 x x964 x x1174 x x1174 x x1384 x x754x x964 x x1174 x x1174 x x1384 x718 Machine weight kg Sound level Sound power dba Water pressure drop Cooling kpa Heating kpa Fan Air flow rate m³/h Available pressure Pa Water connections Std. heat exchanger inch 3/4 1 3/4 1 Required power supply V / f / Hz 230/1/50 Water flow Cooling l/h 674 1,064 1,339 1,514 2,056 2,833 3, ,064 1,339 1,514 2,056 2,833 3,140 Heating l/h 674 1,064 1,339 1,514 2,056 2,833 3, ,392 1,856 * : T(2-pipe) - F(4-pipe)

58 58 MEASURING CONDITIONS CHILLERS Cooling Water 7 C / 12 C Ambient temperature : 35 C Air-cooled Heating Water 45 C / 50 C Ambient temperature : 7 C Remote evaporator Suction dewpoint : 5 C Ambient temperature : 35 C Condensing temp : 45 C Remote condenser Cooling Water 7 C / 12 C Liquid temp. : 40 C Cooling Evaporator water : 7 C / 12 C Water condenser : 30 C / 35 C Water-cooled Heating Evaporator water : 7 C / 12 C Water condenser : 40 C / 45 C FAN COILS Measuring conditions (at nominal air flow and ESP): COOLING: air temperature entering the unit: 27 C/19 C, water temperature entering the unit 7 C, water temperature leaving the unit 12 C - HEATING: room air temperature 20 C, for 2-pipe units: water temperature entering 50 C - water flow rate same as for the cooling test, for 4-pipe units: water temperature entering 70 C - water temperature leaving 60 C

59 59

60 Naamloze Vennootschap Zandvoordestraat 300 B-8400 Oostende, Belgium BTW: BE RPR Oostende Daikin s unique position as a manufacturer of air conditioning equipment, compressors and refrigerants has led to its close involvement in environmental issues. For several years Daikin has had the intention to become a leader in the provision of products that have limited impact on the environment. This challenge demands the eco design and development of a wide range of products and an energy management system, resulting in energy conservation and a reduction of waste. Daikin Europe N.V. is approved by LRQA for its Quality Management System in accordance with the ISO9001 standard. ISO9001 pertains to quality assurance regarding design, development, manufacturing as well as to services related to the product. ISO14001 assures an effective environmental management system in order to help protect human health and the environment from the potential impact of our activities, products and services and to assist in maintaining and improving the quality of the environment. Daikin units comply with the European regulations that guarantee the safety of the product. Daikin Europe N.V. participates in the Eurovent Certification Programme for Air Conditioners (AC). Liquid Chilling Packages (LCP) and Fan Coil Units (FC); the certified data of certified models are listed in the Eurovent Directory. Certification is valid for air cooled models <600kW and water cooled models <1500kW. The present leaflet is drawn up by way of information only and does not constitute an offer binding upon Daikin Europe N.V.. Daikin Europe N.V. has compiled the content of this leaflet to the best of its knowledge. No express or implied warranty is given for the completeness, accuracy, reliability or fitness for particular purpose of its content and the products and services presented therein. Specifications are subject to change without prior notice. Daikin Europe N.V. explicitly rejects any liability for any direct or indirect damage, in the broadest sense, arising from or related to the use and/or interpretation of this leaflet. All content is copyrighted by Daikin Europe N.V. Daikin products are distributed by: EPCEN /08 Copyright Daikin Printed on non-chlorinated paper. Prepared by La Movida, Belgium Responsible Editor: Daikin Europe N.V., Zandvoordestraat 300, B-8400 Oostende