PARTS LIST MANUAL Model SS20
|
|
- Kathlyn McKinney
- 6 years ago
- Views:
Transcription
1 E-SS20-PL-093 PARTS LIST MANUAL Model SS20 REVISED STARTING SERIAL # Model SS20-20H Model SS20-3H 20 & 6 SELF-PROPELLED CONCRETE & ASPHALT SAWS SKU # MODEL # SIZE POWER OPTION SS20-20H 20 HONDA GASOLINE ENGINE MODEL GX SS20-25P 20 KOHLER COMMAND PROPANE ENGINE MODEL CH SS20-3H 6 HONDA GASOLINE ENGINE MODEL GX Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page
2 E-SS20-PL-093 READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT. Death or serious injury could occur if this machine is used improperly. SAFETY SAFETY MESSAGES MESSAGES Safety Instructions are proceeded by a graphic alert symbol of DANGER, WARNING, or CAUTION. Indicates an imminent hazard which, if not avoided, will result in death or serious injury. Indicates an imminent hazard which, if not avoided, can result in death or serious injury. Indicates hazards which, if not avoided, could result in serious injury and or damage to the equipment. GASOLINE/PROPANE POWERED EQUIPMENT Engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Gasoline is extremely flammable and poisonous. It should only be dispensed in well ventilated areas, and with a cool engine. Small gasoline engines produce high concentrations of carbon monoxide (CO) example: a 5 HP 4 cycle engine operation in an enclosed 00,000 cu. ft. area with only one change of air per hour is capable of providing deadly concentrations of CO in less than fifteen minutes. Five changes of air in the same area will produce noxious fumes in less than 30 minutes. Gasoline or propane powered equipment should not be used in enclosed or partially enclosed areas. Symptoms of CO poisoning include, headache, nausea, weakness, dizziness, visual problems and loss of consciousness. If symptoms occur - get into fresh air and seek medical attention immediately. ELECTRICAL POWERED EQUIPMENT Extreme care must be taken when operating electric models with water present: Ensure power cord is properly grounded, is attached to a Ground-Fault-Interrupter (GFI) outlet, and is undamaged. Check all electrical cables - be sure connections are tight and cable is continuous and in good condition. Be sure cable is correctly rated for both the operating current and voltage of this equipment. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with qualified electrician or service person if there is any doubt as to whether the outlet is properly grounded. Adhere to all local codes and ordinances. NOTE: In the event of a malfunction or breakdown, grounding provides a path of least resistance for the electric current to dissipate. The motor is equipped with a grounded plug and must be connected to an outlet that is properly installed and properly grounded. DO NOT modify the plug provided on the motor. If the plug does not fit the outlet have a qualified electrician install the proper receptacle. Switch motor OFF before disconnecting power. Do not disconnect power by pulling cord. To disconnect, grasp the plug, not the cord. Unplug power cord at the machine when not in use and before servicing. GENERAL INSTRUCTIONS Equipment should only be operated by trained personnel in good physical condition and mental health (not fatigued). The operator and maintenance personnel must be physically able to handle the bulk weight and power of this equipment. This is a one person tool. Maintain a safe operating distance to other personnel. It is the operators responsibility to keep other people (workers, pedestrians, bystanders, etc.) away during operation. Block off the work area in all directions with roping, safety netting, etc. for a safe distance. Failure to do so may result in others being injured by flying debris or exposing them to harmful dust and noise. This equipment is intended for commercial use only. For the operator s safety and the safety of others, always keep all guards in place during operation. Never let equipment run unattended. Personal Protection Equipment and proper safety attire must be worn when operating this machinery. The operator must wear approved safety equipment appropriate for the job such as hard hat and safety shoes when conditions require. Hearing protection MUST be used (operational noise levels of this equipment may exceed 85db). Eye protection MUST be worn at all times. Keep body parts and loose clothing away from moving parts. Failure to do so could result in dismemberment or death. Do not modify the machine. Stop motor/engine when adjusting or servicing this equipment. Maintain a safe operating distance from flammable materials. Sparks from the cutting-action of this machine can ignite flammable materials or vapors. DUST WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are: Lead from lead-based paints, and Crystalline silica from bricks and concrete and other masonry products. Your risk of exposure to these chemicals varies depending on how often you do this type of work. To reduce your risk: work in a well ventilated area, use a dust control system, such as an industrial-style vacuum, and wear approved personal safety equipment, such as a dust/particle respirator designed to filter out microscopic particles. 203 JWA Page 2 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
3 PARTS LIST MANUAL MODEL SS20 E-SS20-PL-093 Section TABLE OF CONTENTS Page Numbers Safety Messages and General Instructions How To Order Replacement Parts Illustration : Frame Grouping , 5 Illustration 2: Arbor & 20 Blade Guard Grouping , 7 Illustration 3: Arbor & 6 Blade Guard Grouping , 9 Illustration 4: Transmission Grouping , Illustration 5: Engine Grouping for Honda GX , 3 Illustration 6: Fuel Tank Grouping for Honda GX , 5 Illustration 7: Engine Grouping for Kohler Command CH , 7 Illustration 8: Battery Grouping Illustration 9: Operating Controls Illustration 0: Engine Grouping for Honda GX , 2 Illustration : Belt Drive Grouping , 23 Illustration 2: Blade Depth Gauge Kit , 25 Illustration 3: Optional Water Pump Kit , 27 Wiring Diagram for SS20-20H , 29 Wiring Diagram for SS20-25P Wiring Diagram for SS20-3H Decal Sheet P/N Decal Sheet P/N Notes Blank Page (This page was left blank intensionally) Limited Equipment Warranty of Sale - Terms & Conditions (Back Page) HOW TO ORDER REPLACEMENT PARTS To insure product safety and reliability, always use genuine EDCO replacement parts when making repairs to the equipment. When calling for parts, specify the MODEL and SERIAL number of the machine, which can be found on the NAME PLATE. Keep that information in the space provided. In addition to this information, give part number, description, and quantity as listed on the parts list to your parts representative. Please note: Due to improvements and changes in the equipment, the illustrations shown may be different than the actual machine. FILL IN INFORMATION BELOW Date of Purchase Model # Serial # SKU # 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 3
4 E-SS20-PL-093 ILLUSTRATION : FRAME GROUPING 203 JWA Page 4 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
5 E-SS20-PL-093 PARTS LISTING - ILLUSTRATION : FRAME GROUPING ITEM # PART # DESCRIPTION QTY MAIN FRAME AXLE 3/4DIA. X 7-3/8L COLLAR, LOCKING 3/4 ID WHEEL 8 X 2 X 3/4 BRG, SBR RUBBER WASHER.755 ID X.25 OD X.060 THK WASHER, LOCK /2 ZINC SCREW, CAP /2-20 X FORK W/ PIVOT TUBE WASHER, FLAT 3/4 SAE ZINC WHEEL 4 X -/2 X 3/4 BRG. ALUM/RUB PIN, COTTER 3/6 X -/ SHAFT 3/4 DIA. X 9 L SCREW, CAP /2-20 X 2-/ NUT, HEX NYLON LOCK /2-20 ZINC LINKAGE, CUT CONTROL FITTING, GREASE /4-28 STRAIGHT HANDWHEEL, LRG. W/ 5/8-8 X 3 ROD KNOB, BALL -3/8 W/ /2-3THD, BLK SLEEVE F/ /2 CAPSCREW, TAPERED SCREW, SKT. HD. CAP /2-3 X 4-/ BEARING, THRUST BALL 5/ WASHER, FLAT 5/8 SAE ZINC COLLAR, LOCKING 5/8 ID CONSOLE DEPTH LOCK, SS BOLT, CARRIAGE 5/6-8 X FULL THD WASHER, FLAT 5/6 SAE ZINC NUT, HEX NYLON LOCK 5/6-8 ZINC CONSOLE, SS20-20H & SS20-3H 5203P CONSOLE, SS20-25P WASHER, FLAT 5/6 SAE ZINC WASHER, LOCK 5/6 ZINC SCREW, CAP 5/6-8 X 3/ GROMMET -45/64ID X /8GRV. X 2GD GROMMET 3/8ID X /8GRV. X 5/8GD ITEM # PART # DESCRIPTION QTY ROPE CLEAT, NYLON JAM 3/6-5/ SCREW, MACHINE 0-32 X 5/8, SLT.FLT WASHER, FLAT #0 SAE ZINC NUT, KEPS LOCK 0-32 ZINC HANDLE BAR 24, ZINC PLATED GRIP, HAND MODEL AT PIN, DETENT RING 3/6 X -5/6 E.L KNOB, STAR CLAMPING 3/8-6 X STD ROPE, GUIDE BAR, SS BAIL, LIFTING, SS SCREW, CAP 3/8-24 X WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-24 ZINC COVER, BELT, SS-20 HONDA 5205K COVER, BELT, SS-20 KOHLER SCREW, CAP /4-20 X 3/ WASHER, LOCK /4 ZINC WASHER, FLAT /4 SAE ZINC COVER, ARBOR SCREW, CAP 3/8-6 X 3-3/ WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC GUIDE BAR PLUG, SQ. TUBE X 4 GA., BLACK WHEEL 4 X -3/8 X 3/8 BORE WASHER, FLAT 3/8 SAE ZINC NUT, HEX NYLON LOCK 3/8-6 ZINC GUIDE POINTER, FRONT SCREW, CAP /2-3 X NUT, HEX NYLON LOCK /2-3 ZINC GUIDE POINTER, REAR SCREW, CAP /4-20 X /2 ZINC 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 5
6 E-SS20-PL-093 ILLUSTRATION 2: ARBOR & 20 BLADE GUARD GROUPING MODELS SS20-20H & SS20-25P 203 JWA Page 6 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
7 E-SS20-PL-093 PARTS LISTING - ILLUSTRATION 2 : ARBOR & 20 BLADE GUARD GROUPING ITEM # PART # DESCRIPTION QTY C ARBOR ASSY. W/ 4 GROOVE SHEAVE (INCLUDES ITEMS 2 THRU ) ARBOR SHAFT 23-3/8 L BEARING, BALL TPB KEY /4SQ X 2-/ BUSHING, SHEAVE SH X BORE SHEAVE 3.65 OD X 4GR.3V X SH 7 02 PIN, ROLL 5/6 X ARBOR BACKING PLATE ARBOR BLADE CAP 4 OD W/ HOLE WASHER, LOCK, INT. TOOTH NUT, HEX JAM -4 ZINC GRADE A SCREW, CAP 3/8-6 X 3/ WASHER, LOCK 3/8 ZINC WRENCH, ARBOR, -/2 OPEN END C BLADE GUARD ASSEMBLY 20 (INCLUDES ITEMS 6, 7, AND 8) BLADE GUARD NOZZLE, COOLANT /8MPT W/ 6 TUBES BARB ELBOW 90, 3/8HOSE X /8MPT SCREW, CAP /2-20 X 4-/ WASHER, LOCK /2 ZINC SCREW, CAP 3/8-6 X WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC HOSE, WATER 3/8 ID X 46 L CLAMP, HOSE, SAE #6, ADJ. TO 3/ BARB, 3/8 HOSE X /4MPT (BRASS) PIPE TEE, FEMALE /4 NPT (BRASS) BUSHING, HEX /4 X /8 NPT (BRASS) SWITCH, PRESSURE, N/O (MODEL SS20-20H) SWITCH, PRESSURE, N/C (MODEL SS20-25P) SWITCH, TOGGLE SPDT (MODEL SS20-20H) SWITCH, TOGGLE SPST (MODEL SS20-25P) NIPPLE, HEX /4 NPT (BRASS) BUSHING, HEX /2 X /4 NPT (BRASS) NIPPLE, HEX /2NPT (BRASS) VALVE, BALL /2 FPT CONN., SWIVEL FEM. 3/4HOSE X /2MPT SCREW, CAP /2-20 X 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 7
8 E-SS20-PL-093 ILLUSTRATION 3: ARBOR & 6 BLADE GUARD GROUPING MODEL SS20-3H 203 JWA Page 8 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
9 E-SS20-PL-093 PARTS LISTING - ILLUSTRATION 3 : ARBOR & 6 BLADE GUARD GROUPING ITEM # PART # DESCRIPTION QTY B ARBOR ASSY. W/ 3 GROOVE SHEAVE (INCLUDES ITEMS 2 THRU ) ARBOR SHAFT 23-3/8 L BEARING, BALL TPB KEY /4SQ X 2-/ BUSHING, SHEAVE SH X BORE SHEAVE 3.65 OD X 3GR.3V X SH 7 02 PIN, ROLL 5/6 X ARBOR BACKING PLATE ARBOR BLADE CAP 4 OD W/ HOLE WASHER, LOCK, INT. TOOTH NUT, HEX JAM -4 ZINC GRADE A SCREW, CAP 3/8-6 X 3/ WASHER, LOCK 3/8 ZINC WRENCH, ARBOR, -/2 OPEN END C BLADE GUARD ASSEMBLY 6 (INCLUDES ITEMS 6, 7, AND8) BLADE GUARD NOZZLE, COOLANT /8MPT W/ 6 TUBES BARB ELBOW 90, 3/8HOSE X /8MPT SCREW, CAP /2-20 X 4-/ WASHER, LOCK /2 ZINC SCREW, CAP 3/8-6 X WASHER, LOCK 3/8 ZINC WASHER, FLAT 3/8 SAE ZINC HOSE, WATER 3/8 ID X 46 L CLAMP, HOSE, SAE #6, ADJ. TO 3/ BARB, 3/8 HOSE X /4MPT (BRASS) BUSHING, HEX /2 X /4 NPT (BRASS) NIPPLE, HEX /2NPT (BRASS) VALVE, BALL /2 FPT CONN., SWIVEL FEM. 3/4HOSE X /2MPT SCREW, CAP /2-20 X 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 9
10 E-SS20-PL-093 ILLUSTRATION 4: TRANSMISSION GROUPING 203 JWA Page 0 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
11 E-SS20-PL-093 PARTS LISTING - ILLUSTRATION 4: TRANSMISSION GROUPING ITEM # PART # DESCRIPTION QTY. ITEM # PART # DESCRIPTION QTY TRANSMISSION, HYDROSTATIC BELL CRANK, DRIVE LINKAGE SPROCKET #35 X.67 BORE SCREW, CAP 3/8-24 X 3-/ KEY, WOODRUFF /8 X /2 (#404) WASHER, FLAT 3/8 SAE ZINC SHEAVE, TRANS. 4 OD X GR. X.67 B NUT, HEX LOCK 3/8-24 ZINC FAN BLADE W/ PLATE 7, TRANS WASHER, LOCK 5/6 ZINC WASHER, LOCK /4 ZINC NUT, HEX 5/6-24 ZINC SCREW, CAP /4-20 X 3/ SCREW, CAP /2-3 X MOUNT, TRANSMISSION WASHER, FLAT /2 SAE ZINC BOLT, CARRIAGE 3/8-6 X 3 FULL THD SPRING, COMP..828 OD X 2 FL WASHER, GARRET 7/32 X X NUT, HEX LOCK /2-3 ZINC 2 08 WASHER, LOCK 3/8 ZINC LINKAGE, ROD 3/8 X 3 L NUT, HEX 3/8-6 ZINC NUT, HEX 3/8-24 ZINC TRANS. CONTROL ARM 54 A 099 ROD END, FEMALE 3/8-24 R.H. THREAD 4 08 WASHER, LOCK 3/8 ZINC 54 B 099L ROD END, FEMALE 3/8-24 L.H. THREAD NUT, HEX 3/8-6 ZINC NUT, HEX LOCK 3/8-24 ZINC JACKSHAFT 3/4 X SPACER, STEEL 9/6OD X 3/8ID X 7/ KEY 3/6SQ X SCREW, CAP 3/8-24 X -/4 PLATED BEARING, BALL 3/4 2-HOLE FLANGE SCREW, CAP 3/8-24 X -/4 PLATED FITTING, GREASE /4-28 X WASHER, LOCK 3/8 ZINC DRIVER, REAR WHEEL, -5/8 OD 25T WASHER, FLAT 3/8 SAE ZINC PIN, ROLL /4 X / SCREW, CAP 3/8-24 X -/ SCREW, CAP 3/8-24 X -/4 PLATED WASHER, FLAT 3/8 SAE ZINC WASHER, FLAT 3/8 SAE ZINC NUT, HEX LOCK 3/8-24 ZINC WASHER, LOCK 3/8 ZINC LEVER, CLUTCH NUT, HEX 3/8-24 ZINC KNOB, BALL -3/8 W/ /2-3THD, BLK CHAIN #35 X 24-/2 + OL + CL LEVER, DRIVE SPROCKET #35B54 X 3/4 BORE W/ KW PLATE, DRIVE LEVER PRESSURE SCREW, CAP /2-20 X SCREW, CAP /4-20 X -/ WASHER, FLAT /2 SAE ZINC WASHER, FLAT /4 SAE ZINC NUT, HEX LOCK /2-20 ZINC SPRING, COMP..468 OD X.25 FL BALL JOINT ASSY. 5/6-24 R.H. THRD NUT, HEX LOCK /4-20 ZINC LINKAGE, ROD 5/6 X 9 L MOUNT BRKT., DRIVE LEVER NUT, HEX 5/6-24 ZINC SCREW, CAP /2-20 X -/ L BALL JOINT ASSY. 5/6-24 L.H. THRD WASHER, BELLEVILLE /2ID X 3/64THK WASHER, LOCK 5/6 ZINC WASHER, FIBER 2-/4OD X /2ID X / NUT, HEX 5/6-24 ZINC WASHER, FLAT /2 SAE ZINC LINKAGE, ROD 5/6 X 3 L NUT, HEX LOCK /2-20 ZINC NUT, HEX 5/6-24 ZINC SCREW, CAP /4-20 X 3/ BALL JOINT ASSY. 5/6-24 R.H. THRD WASHER, FLAT /4 SAE ZINC WASHER, LOCK 5/6 ZINC NUT, HEX NYLON LOCK / NUT, HEX 5/6-24 ZINC 2 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page
12 E-SS20-PL-093 ILLUSTRATION 5: ENGINE GROUPING FOR HONDA GX630 MODEL SS20-20H REVISED STARTING S/N JWA Page 2 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
13 PARTS LISTING - ILLUSTRATION 5: ENGINE GROUPING FOR HONDA GX630 ITEM # PART # DESCRIPTION QTY ENGINE, HONDA GX630R-TXF MUFFLER, HONDA VHRM AIR CLEANER, HONDA DNLS5 (COMPLETE) ELEMENT, AIR FILTER, DNLS P ELBOW, SOLDER JOINT -/4 X SCREW, CAP STSHW 0-24 X / REGULATOR RECTIFIER (INCLUDED W/ ENGINE) WASHER, LOCK /4 ZINC SCREW, CAP /4-20 X ADAPTER, 20MM X.5 TO /4FPT ELBOW, STREET /4NPT X 45 (BRASS) 579 BARB, PUSH-ON /2HOSE X /4 MPT HOSE, PUSH-ON /2 ID X 7 L BARB, PUSH-ON /2HOSE X /2MPT PIPE PLUG /2 NPT (BRASS) BRACKET, OIL DRAIN SCREW, CAP /4-20 X 3/ WASHER, LOCK /4 ZINC WASHER, FLAT /4 SAE ZINC MOUNT, ENGINE, SS-6A/20/ BOLT, TAP /2-3 X 4 (FULL THREAD) NUT, HEX /2-3 ZINC TOGGLE PAD 7/8 D X 5/6 H X / BOLT, CARRIAGE 3/8-6 X -3/ WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-6 ZINC BOLT, CARRIAGE 3/8-6 X ZINC WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-6 ZINC SCREW, CAP /2-20 X WASHER, FLAT /2 SAE ZINC NUT, HEX LOCK /2-20 ZINC SWITCH ASSY., IGN., HONDA GX630 (INCL. W/ ENGINE) HOUR METER, INDUCTIVE CABLE, CHOKE CONTROL 72 (CUT TO 28 ) CABLE, TURN-TO-LOCK CONTROL 72 (CUT TO 37 ) R SWITCH COMPLETE, E-STOP W/ RED N.C. CONTACT BUTTON ONLY, PUSH-TURN TO RESET E-STOP CLIP ONLY, E-STOP 333E CONTACT BLOCK ONLY, N.C. E-STOP 33E0 RED E-SS20-PL Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 3
14 E-SS20-PL-093 ILLUSTRATION 6: FUEL TANK GROUPING FOR HONDA GX630 REVISED STARTING S/N JWA Page 4 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
15 E-SS20-PL-093 PARTS LISTING ILLUSTRATION 6: FUEL TANK GROUPING FOR HONDA GX630 ITEM # PART # DESCRIPTION QTY. 522 TANK, FUEL 3 GAL., SS PIPE PLUG /8 NPT (BRASS) INCLUDED W/ ITEM - FUEL TANK CAP, FUEL TANK W/ VITON GASKET (INCLUDES TEATHER CHAIN) TUBE, FUEL PICK-UP BARB ELBOW 90, /4HOSE X /8MPT CLAMP, HOSE, SPRING-BAND 7/ TUBING, EVAP LOW PERM. FUEL /4 ID X 23 (BULK P/N 0948) 2 FT TUBING, EVAP LOW PERM. FUEL /4 ID X 6 (BULK P/N 0948) /2 FT TUBING, EVAP LOW PERM. FUEL 3/8 ID X 52-/2 (BULK P/N 5256) 4-/2 FT CANISTER, CARBON A FOR HONDA (INLUDES 2 MOUNTING PADS) 0834 SCREW, CAP /4-20 X /2 ZINC WASHER, LOCK, INT. TOOTH / TIE, CABLE, BLACK NYLON -/ SCREW, CAP 5/6-8 X 3/ WASHER, LOCK 5/6 ZINC WASHER, FLAT 5/6 SAE ZINC SCREW, CAP /4-20 X 3/ WASHER, FLAT /4 SAE ZINC NUT, KEPS LOCK /4-20 ZINC CLAMP, LOOM, 5/8 (SAE SIZE 0) 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 5
16 E-SS20-PL-093 ILLUSTRATION 7: ENGINE GROUPING FOR KOHLER COMMAND CH730 PROPANE MODEL SS20-25P 203 JWA Page 6 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
17 E-SS20-PL-093 PARTS LISTING - ILLUSTRATION 7: ENGINE GROUPING FOR KOHLER COMMAND CH730 PROPANE ITEM # PART # DESCRIPTION QTY ENGINE, KOHLER 25HP COMMAND PROPANE MOUNT, ENGINE, SS-6A/20/ BOLT, CARRIAGE 3/8-6 X -3/ BOLT, CARRIAGE 3/8-6 X WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-6 ZINC BOLT, TAP /2-3 X 4 (FULL THREAD) NUT, HEX /2-3 ZINC TOGGLE PAD 7/8 D X 5/6 H X / BOLT, CARRIAGE 3/8-6 X ZINC WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-6 ZINC SCREW, CAP /2-20 X WASHER, FLAT /2 SAE ZINC NUT, HEX LOCK /2-20 ZINC BARB, PUSH-ON /2HOSE X 3/8MPT HOSE, PUSH-ON /2 ID X 9-/2 L BARB, PUSH-ON /2HOSE X /2MPT BRACKET, OIL DRAIN PIPE PLUG /2 NPT (BRASS) SCREW, CAP /4-20 X 3/ WASHER, LOCK /4 ZINC WASHER, FLAT /4 SAE ZINC G SWITCH COMPLETE, E-STOP... W/ GREEN N.O. CONTACT BUTTON ONLY, PUSH-TURN RESET CLIP ONLY, E-STOP 333E CONTACT BLOCK, N.O. 33E0 GREEN ITEM # PART # DESCRIPTION QTY CABLE, TURN-TO-LOCK CONTROL 72 (CUT TO 32 ) CABLE, CHOKE CONTROL 72 (CUT TO 30 ) HOUR METER, INDUCTIVE SWITCH, KEY, KOHLER S ELBOW, STREET /4NPT X 45 (BRASS) ELBOW, 3/8FLARE X /4MPT X HOSE, HIGH PRESSURE 5/6 #6HPSS25UL COUPLING, REGO 74F FEMALE CLAMP, LOOM, 5/8 (SAE SIZE 0) SCREW, CAP /4-20 X 3/ WASHER, FLAT /4 SAE ZINC NUT, KEPS LOCK /4-20 ZINC PROPANE TANK 33LB. VERT. LIQ. WD PROPANE TANK MOUNTING BRKT TB MOUNT PLATE, PROPANE TANK SCREW, CAP 3/8-6 X WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-6 ZINC SCREW, CAP 5/6-8 X 3/ WASHER, LOCK 5/6 ZINC WASHER, FLAT 5/6 SAE ZINC BASE SUPPORT, PROPANE TANK SCREW, CAP 5/6-8 X WASHER, LOCK 5/6 ZINC WASHER, FLAT 5/6 SAE ZINC 2 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 7
18 E-SS20-PL-093 ILLUSTRATION 8: BATTERY GROUPING MODELS SS20-20H & SS20-25P ITEM # PART # DESCRIPTION QTY. 840 BATTERY 2 VOLT/300 CCA(SMALL ENG.) CLAMP, BATTERY HOLD DOWN SCREW, CAP /4-20 X -/ WASHER, FLAT /4 SAE ZINC NUT, HEX NYLON LOCK /4-20 ZINC B CABLE, EYE-EYE 4GA. X 24 (BLACK) CABLE, EYE-EYE 4GA. X 40 (RED) INSULATOR, BAT.TERM. U- STYLE( RED) LOOM, FLEX 5/8 (BULK P/N 0926) 5 FT BOLT, CARRIAGE 5/6-8 X 3/ WASHER, LOCK 5/6 ZINC NUT, HEX 5/6-8 ZINC JWA Page 8 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
19 ILLUSTRATION 9: OPERATING CONTROLS E-SS20-PL-093 ITEM # PART # DESCRIPTION QTY. BLADE SAVER SWITCH (SS20-20H & SS20-25P ONLY) TOGGLE SPDT 3 TERM. (MODEL SS20-20H) TOGGLE SPST 2 TERM. (MODEL SS20-25P) WATER PUMP SWITCH - TOGGLE SPST 2 TERM. (OPTIONAL ON MODEL SS20-20H & SS20-25P) IGNITION SWITCH (SEE ILLUS. 5 OR 7) (MODELS SS20-20H & SS20-25P ONLY) HOUR METER, INDUCTIVE (OPTIONAL ON MODEL SS20-3H) DEPTH CONTROL (SEE ILLUS. ) DEPTH GAUGE (SEE ILLUS. 2) CABLE, CHOKE CONTROL (MODELS SS20-20H & SS20-25P ONLY) THROTTLE CONTROL CABLE SWITCH, EMERGANCY-STOP (SEE ENGINE GROUPINGS & WIRING DIAGRAMS) 0 59 GUIDE ROPE CLEAT (SEE ILLUS., ITEM 34) DRIVE CONTROL LEVER (SEE ILLUS. 6) CLUTCH CONTROL LEVER (SEE ILLUS. 7) WATER HOOK-UP & VALVE (SEE ILLUS. 2 OR 3) EXTENDABLE HANDLES (SEE ILLUS. ) HANDLE LOCK (SEE ILLUS., ITEM 4) 2 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 9
20 E-SS20-PL-093 ILLUSTRATION 0: ENGINE GROUPING FOR HONDA GX390 MODEL SS20-3H 203 JWA Page Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
21 E-SS20-PL-093 PARTS LISTING - ILLUSTRATION 0: ENGINE GROUPING FOR HONDA GX390 ITEM # PART # DESCRIPTION QTY ENGINE, HONDA GX390UT2-QXC9 CYC.AC MUFFLER CAP, HONDA #833-ZE RIVET, BLIND /8 X.275L X.250HD BARB, PUSH-ON 3/8HOSE X M2-.5MALE HOSE, PUSH-ON /2 ID X 0 L BARB, PUSH-ON /2HOSE X /2MPT BRACKET, OIL DRAIN PIPE PLUG /2 NPT (BRASS) SCREW, CAP /4-20 X 3/ WASHER, LOCK /4 ZINC WASHER, FLAT /4 SAE ZINC MOUNT, ENGINE, SS-6A/20/ BOLT, TAP /2-3 X 4 (FULL THREAD) NUT, HEX /2-3 ZINC TOGGLE PAD 7/8 D X 5/6 H X / BOLT, CARRIAGE 3/8-6 X -3/ WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-6 ZINC BOLT, CARRIAGE 3/8-6 X ZINC WASHER, FLAT 3/8 SAE ZINC WASHER, LOCK 3/8 ZINC NUT, HEX 3/8-6 ZINC SCREW, CAP /2-20 X WASHER, FLAT /2 SAE ZINC NUT, HEX LOCK /2-20 ZINC G SWITCH COMPLETE, E-STOP W/ GREEN N.O. CONTACT BUTTON ONLY, PUSH-TURN TO RESET CLIP ONLY, E-STOP 333E CONTACT BLOCK ONLY, N.O. 33E0 GREEN CABLE, TURN-TO-LOCK CONTROL 72 (CUT TO 23 ) HOUR METER, INDUCTIVE (OPTIONAL) GUARD, CONSOLE REAR, SS-6A/ SCREW, CAP /4-20 X 3/ WASHER, LOCK /4 ZINC WASHER, FLAT /4 SAE ZINC 4 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 2
22 E-SS20-PL-093 ILLUSTRATION : BELT DRIVE GROUPING ENGINE ENGINE RPM MODEL SS20 BELT DRIVE SPECIFICATION CHART BLADE DIAMETER BLADE SPEED (RPM) ENGINE SHEAVE ARBOR SHEAVE ARBOR BELTS TRANSMISSION BELT HONDA GX Groove Groove 3VX335 3-Required A50 HONDA GX Groove Groove 3VX335 4-Required A46 KOHLER CH730 PROPANE Groove Groove 3VX355 4-Required A JWA Page Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
23 E-SS20-PL-093 PARTS LISTING - ILLUSTRATION : BELT DRIVE GROUPING ITEM # PART # DESCRIPTION QTY BELT, ARBOR 3VX335 (HONDA GX390 & GX630) 3VX355 (KOHLER CH730) BUSHING, SHEAVE JA X -/8 BORE (HONDA GX630 ONLY) 3 SHEAVE OD X 4GR.3V X JA (HONDA GX630) 2.8 OD X 4GR.3V X -7/6 BORE (KOHLER CH730) KEY 3/8 SQ X 3 (HONDA GX630 & KOHLER CH730) SHEAVE 3.65 OD X 3GR.3V X SH (HONDA GX390) BUSHING, SHEAVE SH X BORE (HONDA GX390) INCLUDES KEY 7 74 BOLT, TAP /4-20 X 2 (FULL THD) WASHER, LOCK /4 ZINC BUSHING, SHEAVE TAPER-LOCK BORE (HONDA GX390) TAPER-LOCK -/8 B (HONDA GX630) TAPER-LOCK 60-7/6 B (KOHLER CH730) SHEAVE 4.5 OD X GR.AB X TAPER-LOCK BELT, TRANSMISSION A-50 (HONDA GX390) A-46 (HONDA GX630 & KOHLER CH730) IDLER PULLEY 2.75 X 3/4FLAT X 3/ SCREW, CAP 3/8-24 X 2-/ SPRING, EXT. OD X 3-5/ NUT, HEX LOCK 3/8-24 ZINC WASHER, FLAT SAE ZINC SPACER, STEEL 9/6OD X 3/8ID X 7/ NUT, HEX 3/8-24 ZINC SCREW, CAP /2-20 X -/ WASHER, FLAT /2 SAE ZINC IDLER ARM NUT, HEX LOCK /2-20 ZINC SHEAVE 3.65 OD X 4GR.3V X SH (HONDA GX630 & KOHLER CH730) SHEAVE 3.65 OD X 3GR.3V X SH (HONDA GX390) BUSHING, SHEAVE SH X BORE (INCLUDES SCREWS & WASHERS) 3 & Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 23
24 E-SS20-PL-093 ILLUSTRATION 2: BLADE DEPTH GAUGE KIT PART # 5238 STANDARD ON MODELS SS20-20H & SS20-25P OPTIONAL ON MODEL SS20-3H 203 JWA Page Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
25 E-SS20-PL-093 PARTS LISTING - ILLUSTRATION 2: BLADE DEPTH GAUGE KIT - PART # 5238 ITEM # PART # DESCRIPTION QTY WHEEL, DEPTH GAUGE DEPTH GAUGE DECAL (PART OF DECAL KIT, PART # 9224) WASHER, FLAT 3/8 SAE ZINC SCREW, CAP 3/8-24 X 2-/ SHIM 3/8 X 5/8 X NUT, HEX LOCK 3/8-24 ZINC NUT, HEX NYLON LOCK 3/8-24 ZINC CABLE, DEPTH GAUGE 3/32 X 25 L SPRING, EXT. 6 L SCREW, CAP /4-20 X 0602 WASHER, FLAT /4 SAE ZINC NUT, KEPS LOCK /4-20 ZINC NUT, HEX NYLON LOCK /4-20 ZINC BOLT, SPADE 3/8-6 X -5/ NUT, HEX 3/8-6 ZINC WASHER, LOCK 3/8 ZINC 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 25
26 E-SS20-PL-093 ILLUSTRATION 3: OPTIONAL WATER PUMP KIT PART # 5270 *MODELS SS20-20H & SS20-25P ONLY* 203 JWA Page Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
27 E-SS20-PL-093 PARTS LISTING - ILLUSTRATION 3: OPTIONAL WATER PUMP KIT PART # 5270 ITEM # PART # DESCRIPTION QTY PUMP, WATER, 2VDC, FLOJET QUAD SCREW, CAP /4-20 X -/ WASHER, FLAT /4 SAE ZINC WASHER, LOCK /4 ZINC NUT, ACORN / PUMP QUAD PORT BARB ELBOW / CLAMP, HOSE, SAE #6, ADJ. TO 3/ HOSE, WATER /2 ID X 4-7/8 L HOSE, WATER /2 ID X 4 L HOSE, WATER /2 ID X 2 L 5047 BARB ELBOW 90, /2HOSE X /2MPT STRAINER, NYLON T-STYLE /2FPT BARB, /2HOSE X /2MPT (PLASTIC) FUSE & HOLDER, 0 AMP SWITCH, TOGGLE SPST 5/0A-5/250V WIRE, RED 4AWG X 30 L CONNECTOR, BUTT 6-4GA. INSULATED TERM., RING #0 6-4GA. INSULATED TERM., RING 5/6 6-4GA. INSULATED * BARB, PUSH-ON /2HOSE X /4 MPT * BARB ELBOW 90, 3/8HOSE X /4MPT * CLAMP, LOOM, 5/8 (SAE SIZE 0) * SCREW, CAP /4-20 X 3/4 * WASHER, FLAT /4 SAE ZINC * NUT, KEPS LOCK /4-20 ZINC * DECAL, WATER PUMP ON-OFF (PART OF DECAL KIT # 9224) - ** PIPE TEE, FEMALE /4 NPT (BRASS) - ** BUSHING, HEX /4 X /8 NPT (BRASS) - ** SWITCH, PRESSURE, N/O (MODEL SS20-20H) SWITCH, PRESSURE, N/C (MODEL SS20-25P) *** HOSE, WATER 3/8 ID X 45 L - -9 THESE ITEMS ARE PRE-ASSEMBLED *20-26 THESE ITEMS ARE NOT PRE-ASSEMBLED **27-29 THESE ITEMS ARE REUSED FROM THE EXISTING UNIT. THEY ARE SHOWN FOR ASSEMBLY PURPOSES ONLY ***30 THIS ITEM IS REUSED FROM THE EXISTING UNIT. TRIM OFF TO THE APPROPRIATE LENGTH Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 27
28 E-SS20-PL-093 WIRING DIAGRAM FOR MODEL SS20-20H 203 JWA Page Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
29 E-SS20-PL-093 PARTS LISTING WIRING DIAGRAM FOR MODEL SS20-20H ITEM # PART # DESCRIPTION QTY. 538 HOUR METER, INDUCTIVE (INCLUDES 48 BLACK WIRE) BLADE SAVER SWITCH TOGGLE SPDT (3 SCREW TERMINALS) R SWITCH COMPLETE, E-STOP...W/ RED N.C. CONTACT 5257 BUTTON ONLY, PUSH-TURN TO RESET 548 CLIP ONLY, E-STOP 333E 567 CONTACT BLOCK ONLY, N.C. 33E0 RED SWITCH ASSY., IGN. HONDA P/N 3500-Z6L-003 (INCLUDED W/ ENGINE) SWITCH, PRESSURE, N/O WIRE 0 WHITE 4 GA. 2 #0 RING TERM. BOTH ENDS WIRE 20 YELLOW 4 GA. #0 RING TERM. ONE END WIRE 7 RED 4 GA. #0 RING TERM. & FORD BULLET CONN WIRE 58 BLACK 4 GA. FORD BULLET ONE END * WIRE 58 WHITE 4 GA. FORD BULLET CONN. & FORD LINE CONN. * 5446 WIRE 58 WHITE 4 GA BUTT CONN. & 5/6 RING TERM. * WIRE 58 BLUE 4 GA BUTT CONN. & /4 FEM. PUSH-ON TERM. * WIRE 58 YELLOW W/ BLACK STRIPE 4 GA. FORD BULLET CONN. & FORD LINE CONN BATTERY 2 VOLT/300 CCA(SMALL ENG.) CABLE, EYE-EYE 4GA. X 40 (RED) 6 507B CABLE, EYE-EYE 4GA. X 24 (BLACK) SWITCH, TOGGLE SPST 5/0A-5/250V (2 SCREW TERMINALS) FUSE & HOLDER, 0 AMP PUMP, WATER, 2VDC, FLOJET QUAD (OPTIONAL) * THESE WIRES ARE PART OF A WIRE HARNESS ASSEMBLY - PART # Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 29
30 E-SS20-PL-093 WIRING DIAGRAM FOR MODEL SS20-25P REVISED STARTING S/N ITEM # PART # DESCRIPTION QTY. 538 HOUR METER, INDUCTIVE G SWITCH COMPLETE, E-STOP W/ GREEN N.O. CONTACT BUTTON ONLY, PUSH-TURN TO RESET CLIP ONLY, E-STOP 333E CONTACT BLOCK ONLY, N.O. 33E0 GREEN SWITCH, TOGGLE SPST 5/0A-5/250V (2 SCREW TERMINALS) SWITCH, PRESSURE, N/C (NORMALY CLOSED) SWITCH, KEY, KOHLER S CONNECTOR, WIRE HARNESS, MALE TERMINAL, FEM., KOHLER S CONNECTOR, WIRE HARNESS, FEMALE TERMINAL, MALE, KOHLER S CONNECTOR, BULLET FORD 3-WAY STD SWITCH, TOGGLE SPST 5/0A-5/250V (2 SCREW TERMINALS) FUSE & HOLDER, 0 AMP PUMP, WATER, 2VDC, FLOJET QUAD (OPTIONAL) JWA Page Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
31 E-SS20-PL-093 WIRING DIAGRAM FOR MODEL SS20-3H REVISED STARTING S/N ITEM # PART # DESCRIPTION QTY G SWITCH COMPLETE, E-STOP W/ GREEN N.O. CONTACT BUTTON ONLY, PUSH-TURN TO RESET CLIP ONLY, E-STOP 333E CONTACT BLOCK ONLY, N.O. 33E0 GREEN CONN., WIRE QUICK-SPLICE 8-4 GA HOUR METER, INDUCTIVE (OPTIONAL) 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 3
32 E-SS20-PL-093 DECAL SHEET P/N 9223 CAUTION DISCONNECT ELECTRICAL POWER SUPPLY OR SPARK PLUG SS-20 & 24-4 x 7 P/N 9223 RevA To prevent injury when servicing or changing blades or accessories exceeds 85dBA CALIFORNIA PROPOSITION 65 WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. CHECK OIL DAILY edcoinc.com SS JWA Page Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
33 DECAL SHEET P/N 9224 E-SS20-PL-093 SS-20 & x 7 P/N 9224 RevB GREASE BEARINGS DAILY DANGER BEFORE CUTTING INTO ANY SURFACE, INSURE THERE ARE NO BURIED GAS, ELECTRICAL, HIGH PRESSURE AIR, SEWER OR WATER LINES NOTE: Locate this decal so it is visible from operator's position YOU MUST READ OPERATOR S INSTRUCTION MANUAL BEFORE OPERATING DN D EP T H C O N TR O L UP PUSH TO STOP PUSH-TURN TO RESET R 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 33
34 E-SS20-PL-093 NOTES Record here any repairs or changes made to the Equipment 203 JWA Page Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
35 E-SS20-PL-093 THIS PAGE WAS LEFT BLANK INTENSIONALLY 00 Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30) JWA 203 Page 35
36 E-SS20-PL-093 LIMITED EQUIPMENT WARRANTY OF SALE - TERMS & CONDITIONS Equipment Development Company, Inc. herein referred to as EDCO (Seller) warrants that each new unit manufactured by EDCO to be free from defects in material and workmanship in normal use and service for a period of () one year (except for the cutter drum assembly on all model concrete/asphalt planes, in which case the warranty period shall be 90 days) from date of shipment to the original retail or equipment rental center owner. Accessories or equipment furnished and installed on the product by EDCO but manufactured by others, including, but not limited to engines, motors,electrical components, transmissions etc., shall carry the accessory manufacturers own warranty. EDCO will, at its option, repair or replace, at the EDCO factory or at a point designated by EDCO, any part which shall appear to the satisfaction of EDCO inspection to have been defective in material or workmanship. EDCO reserves the right to modify, alter and improve any part or parts without incurring any obligation to replace any part or parts previously sold without such modified, altered or improved part or parts. This warranty is in lieu of and excludes all other warranties, expressed, implied, statutory, or otherwise created under applicable law including, but not limited to the warranty of merchantability and the warranty of fitness for a particular purpose in no event shall seller or the manufacturer of the product be liable for special, incidental, or consequential damages, including loss of profits, whether or not caused by or resulting from the negligence of seller and/or the manufacturer of the product unless specifically provided herein. In addition, this warranty shall not apply to any products or portions there of which have been subjected to abuse, misuse, improper installation, maintenance, or operation, electrical failure or abnormal conditions and to products which have been tampered with, altered, modified, repaired, reworked by anyone not approved by seller or used in any manner inconsistent with the provisions of the above or any instructions or specifications provided with or for the product FORCE MAJEURE Seller s obligation hereunder are subject to, and Seller shall not be held responsible for, any delay or failure to make delivery of all or any part of the Product due to labor difficulties, fires, casualties, accidents, acts of the elements, acts of God, transportation difficulties, delays by a common carrier, inability to obtain Product, materials or components or qualified labor sufficient to timely perform part of or all of the obligations contained in these terms and conditions, governmental regulations or actions, strikes, damage to or destruction in whole or part of manufacturing plant, riots, terrorist attacks or incidents, civil commotions, warlike conditions, flood, tidal waves, typhoon, hurricane, earthquake, lightning, explosion or any other causes, contingencies or circumstances within or without the United States not subject to the Seller s control which prevent or hinder the manufacture or delivery of the Products or make the fulfillment of these terms and conditions impracticable. In the event of the occurrence of any of the foregoing, at the option of Seller, Seller shall be excused from the performance under these Terms and Conditions, or the performance of the Seller shall be correspondingly extended. This document sets forth the terms and conditions pursuant to which the purchaser ( Purchaser ) will purchase and Equipment Development Co.Inc. ( Seller )will sell the products, accessories, attachments (collectively the Products ) ordered by the Purchaser. These terms and conditions shall govern and apply to the sale of Seller s Products to Purchaser, regardless of any terms and conditions appearing on any purchase order or other forms submitted by Purchaser to Seller, or the inconsistency of any terms therein and herein.. PRICE All prices set forth on any purchase order or other document are F.O.B. Sellers facility or distribution point, as may be determined by Seller (F.O.B.Point). All prices are exclusive of any and all taxes, including, but not limited to, excise, sales, use, property or transportation taxes related to the sale or use of the Products, now or hereafter imposed, together with all penalties and expenses. Purchaser shall be responsible for collecting and/or paying any and all such taxes, whether or not they are stated in any invoice for the Products. Unless otherwise specified herein, all prices are exclusive of inland transportation, freight, insurance and other costs and expenses relating to the shipment of the Products from the F.O.B. point to Purchaser s facility. Any prepayment by Seller of freight insurance and other costs shall be for the account of Purchaser and shall be repaid to Seller. 2. PAYMENT TERMS Payment terms are as follows. 2% 0 days (to approved and qualified accounts). Net 30 days. This is a cash discount for invoices paid within 0 days after the invoice date, regardless of date of receipt of shipment. This is not a trade discount and will not be granted to accounts that do not adhere to stated terms. *All past due accounts are subject to a late payment fee of.5% per month or a maximum allowed by law if different, along with the expenses incidental to collection including reasonable attorney s fees and costs. *Seller reserves the right to hold shipments against past due accounts. *Seller reserves the right to alter payment terms. 3. FREIGHT TERMS All shipments will be made F.O.B. shipping point as designated in these Terms and Conditions, and title shall pass at the F.O.B. point. Delivery to the initial common carrier shall constitute delivery to the Purchaser. Any claims for loss or damage during shipment are to be filed with carrier by the Purchaser. Seller will not assume responsibility for the performance of the carrier. Back orders will be shipped in the most practical fashion with charges consistent with our freight policy established with the original order. UPS, FED EX, MAIL or shipments by other couriers are subject to the same terms and conditions as outlined in paragraph #3 Freight Terms. 4. DELIVERY, DAMAGES, SHORTAGES Seller shall use reasonable efforts to attempt to cause the Products to be delivered as provided for in these Terms & Conditions. Delivery to the initial common carrier shall constitute the delivery to the Purchaser. Sellers responsibility, in so far as transportation risks are concerned ceases upon the delivery of the Products in good condition to such carrier at the F.O.B. point and all the Products shall be shipped at the Purchaser s risk. Seller shall not be responsible or liable for any loss of income and/or profits, or incidental, special, consequential damages resulting from Seller s delayed performance in shipment and delivery. 5. RETURN OF DEFECTIVE PRODUCTS Defective or failed material shall be held at the Purchaser s premises until authorization has been granted by Seller to return or dispose of Products. Products that are to be returned for final inspection must be returned Freight Prepaid in the most economical way. Credit will be issued for material found to be defective upon Seller s inspection based on prices at time of purchase. 6. PRODUCTS ORDERED IN ERROR Products may be returned, provided that claim is made and Seller is notified within 7 days of receipt of Products, and the Products are in original buyer s possession not more than 30 days prior to return, subject to Seller s approval. If Products are accepted for return, they must be Freight Prepaid and buyer will be charged a minimum of 5% restocking charge, plus a charge back for outbound freight charges if the original order was shipped prepaid. Returns are not accepted for any Products that are specifically manufactured to meet the buyer s requirement of either specifications or quantity. AGREEMENTS These Terms and Conditions constitute the entire agreement between Seller and Purchaser as it relates to terms and conditions of sale, and supersedes any and all prior oral or written agreements, correspondence, quotations or understandings heretofore in force between the parties relating to the subject matter hereof. There are no agreements between Seller and Purchaser with respect to the Product herein except those specifically set forth in and made part of these terms and conditions. Any additional terms, conditions and/or prices are rejected by Seller. These terms and conditions may be modified, cancelled or rescinded only by a written agreement of both parties executed by their duly authorized agents. USE ONLY GENUINE EDCO PARTS & ACCESSORIES For your own safety, the safety of others and the life of your machine. Equipment Development Company, Inc. 203 JWA Page Thomas Johnson Drive, Frederick, MD USA Phone (30) Fax (30)
Model SS20. EdcoParts.com An ibuy Stores Company PARTS LIST MANUAL 20 & 16 SELF-PROPELLED CONCRETE & ASPHALT SAWS.
PARTS LIST MANUAL REVISED STARTING SERIAL # 3090047 Model SS20 Model SS20-20H Model SS20-3H 20 & 6 SELF-PROPELLED CONCRETE & ASPHALT SAWS SKU # 32600 34600 32800 SIZE POWER OPTION SS20-20H 20 HONDA GASOLINE
More informationSELF-PROPELLED CONCRETE & ASPHALT SAW
STARTING SERIAL # 0920024 PARTS LIST MANUAL Model SS24 SELF-PROPELLED CONCRETE & ASPHALT SAW SKU NO. MODEL NO. POWER OPTION 3800 SS24-24H HONDA GASOLINE ENGINE MODEL GX670 JWA 2009 Page READ AND UNDERSTAND
More informationAn ibuy Stores Company
REVISED STARTING SERIAL NO. 060604 PARTS MANUAL Model SK-4 4 DOWNCUT CONCRETE/ASPHALT WALK BEHIND SAWS SKU NO. MODEL POWER OPTION 45400D SK4-9H HONDA ENGINE 9 HP GX0 45600D SK4-H HONDA ENGINE HP GX40 4800D
More informationPARTS LIST MANUAL MODEL GMS20
REVISED STARTING SERIAL # 121010018 PARTS LIST MANUAL MODEL GMS20 20 GASOLINE POWERED MASONRY SAWS SKU # MODEL # POWER OPTION 22500 GMS20-9H HONDA GASOLINE ENGINE MODEL GX270 21100 GMS20-11H HONDA GASOLINE
More informationPARTS LIST MANUAL MODEL SS26-35K. Gasoline Powered 35 H.P. Kohler Command Pro Self-Propelled Concrete & Asphalt Saw SAW SET-UP OPTIONS
REVISED STARTING SERIAL # 600307 PARTS LIST MANUAL MODEL SS26-35K Gasoline Powered 35 H.P. Kohler Command Pro Self-Propelled Concrete & Asphalt Saw SAW SET-UP OPTIONS SKU NUMBER BLADE GUARD SIZE BLADE
More informationHEAVY-DUTY FLOOR GRINDER / POLISHER
PARTS LIST MANUAL REVISED STARTING SERIAL # 150410237 HEAVY-DUTY FLOOR GRINDER / POLISHER PROPANE MODELS MODEL 2DHDP-18P SKU # 58200 MODEL 2DP-18P SKU # 53900P JWA 2015 Page 1 READ AND UNDERSTAND THE OPERATORS
More informationPARTS LIST MANUAL MODEL BB14G SHOWN WITH OPTIONAL PROCART
REVISED STARTING SERIAL # 09080097 PARTS LIST MANUAL MODEL BB4G SHOWN WITH OPTIONAL PROCART 4 GASOLINE POWERED PORTABLE MASONRY SAWS SKU # MODEL # POWER OPTION 26300 BB4G-5.5H HONDA GX60 W/ CYCLONE AIR
More informationGASOLINE POWERED TRAFFIC LINE REMOVER PARTS LIST MANUAL
REVISED STARTING SERIAL # 2000 GASOLINE POWERED TRAFFIC LINE REMOVER PARTS LIST MANUAL MODEL TLR7-11H PART #77500 Page 1 READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY BEFORE ATTEMPTING
More informationEdcoParts.com An ibuy Stores Company
E-4ECGC-PL-008 REVISED STARTING SERIAL #080000 PARTS LIST MANUAL Models 4-EC & 4-GC FOUR-DISC CONCRETE FLOOR GRINDERS SKU # 5500 54400 53600 52800-230 52800-460 52800-50/220 52800-50/380 52800-50/440 MODEL
More information8 WALK BEHIND SCARIFIER
PARTS LIST MANUAL 8 WALK BEHIND SCARIFIER REVISED STARTING SERIAL # 060110202 MODEL CPM8-9H SHOWN CPM8 SCARIFIERS SKU NO. MODEL POWER OPTIONS 79300 CPM8-9H 9 HP HONDA GX270 GASOLINE ENGINE 79500 CPM8-5B/230/1
More informationUser s Manual and Operating Instructions
User s Manual and Operating Instructions Model Numbers: CL-30P-DDF, CL-20F-DDF, CL-24O-DDF, CL-30-DDF READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Read and understand all of the directions in this manual
More informationFM-17DS & FM-20DS FLOOR MACHINES
PARTS & OPERATING MANUAL FM-17DS & FM-20DS FLOOR MACHINES PLEASE READ THIS BOOK This operator s book has important information for the use and safe operation of this machine. Read this book carefully before
More informationMK-1605 Electric Concrete Saw EXPLODED VIEW & PARTS LIST
www.mkdiamond.com MK-0 Electric Concrete Saw EXPLODED VIEW & PARTS LIST MK-0B Premium Part# 8099 Revision 0 0.08 Manual Part# 79 Caution: Read all safety and operating instructions before using this equipment.
More informationFM-17HD & FM-20HD FLOOR MACHINES
PARTS & OPERATING MANUAL FM-17HD & FM-20HD FLOOR MACHINES PLEASE READ THIS BOOK This operator s book has important information for the use and safe operation of this machine. Read this book carefully before
More informationMC MC MC MC MC833130
Pic-A-Vac Model: MC832085 MC833085 MC832105 MC833105 MC832130 MC833130 OPERATION SERVICE PARTS CARE Revised 8/01 FOR COMMERCIAL USE ONLY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance,
More informationRevised 9/05. Model X-750 Subassembly Parts List
Revised /0 Model Subassembly Parts List Blade Belt Tensioner 0 PART NUMBER DESCRIPTION QTY. -G0-0-0 SHSB, / x / -G0-0-0 SHSB, / x / -X-0-00 Arm, Belt Tensioner -G0-0-00 Washer, Flat /" -0-0-0 Washer, Split
More informationPump Out Vacuums Polyethylene & Steel
Pump Out Vacuums Polyethylene & Steel Operations and Parts Manual 110 volt receptacle on single motor only Models: 415P-AD 429P-AD 415DS IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance,
More informationWAV-26 UPRIGHT WIDE AREA VACUUM
PARTS & OPERATING MANUAL WAV-26 UPRIGHT WIDE AREA VACUUM PLEASE READ THIS BOOK This operator s book has important information for the use and safe operation of this machine. Read this book carefully before
More informationUser s Manual and Operating Instructions
User s Manual and Operating Instructions Model Numbers: PT-18W-DDF-A, PT-20F-DDF-A, PT-20S-DDF, PT-24O-DDF, PT-24-DDF, PT-24-DDF-F, PT-30-DDF, PT-30P-DDF-A, PT-30P-DDF-AF READ AND SAVE THESE INSTRUCTIONS
More informationAURA WIDE AREA VACUUM Parts Manual
AURA WIDE AREA VACUUM Parts Manual INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS READ THIS BOOK This operator s book has important information for the use and safe operation of this machine. Read this
More informationPOLISHERS. MODELS SeaRay 133 OPERATING & MAINTENANCE
POLISHERS MODELS SeaRay 133 INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS This operator s book has important information for the use and safe operation of this machine. Read this book carefully before
More informationWAV-30 WIDE AREA VACUUM
PARTS & OPERATING MANUAL WAV-30 WIDE AREA VACUUM PLEASE READ THIS BOOK This operator s book has important information for the use and safe operation of this machine. Read this book carefully before starting
More informationCREWMAN 20 ORB CREWMAN 28 ORB
E88066-00 E88068-00 E88070-00 CREWMAN 20 ORB CREWMAN 28 ORB 20, 28 Orbital Strip Machines Operator and Parts Manual 400 Van Camp Road Bowling Green, Ohio 43402 Customer Service: 888-GO-BETCO Fax: 800-445-5056
More informationWIDE AREA VACUUM MODEL PF2030 WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPERATING THIS EQUIPMENT.
OPERATOR S MANUAL & PARTS LIST WIDE AREA VACUUM MODEL PF2030 WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPERATING THIS EQUIPMENT. Tacony, Inc., All rights reserved Save These
More informationSINGLE-DISC FLOOR GRINDER
Operator s Instruction Manual SINGLE-DISC FLOOR GRINDER SEC-NG 100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA Phone: 301-638-3326 301-663-1600 Fax: 800-447-3326 301-663-1607 edcoinc.com sales@edcoinc.com
More informationLARGE AREA VACUUM LAV-30
LARGE AREA VACUUM LAV-30 INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS READ THIS BOOK This operator s book has important information for the use and safe operation of this machine. Read this book carefully
More informationPARTS LIST MANUAL MODEL 2-EC and 2-GC
E-ECGC-PL-010 REVISED STARTING SERIAL # 33 PARTS LIST MANUAL MODEL -EC and -GC Two-Disc Concrete Floor Grinder Page 1 E-ECGC-PL-010 READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY BEFORE
More informationD O U B L E A U G E R M O R TA R M I X E R OWNER S MANUAL
D O U B L E A U G E R M O R TA R M I X E R OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationTURBO Fiberglass Cone Fan and Grill Fan 48'' Belt Drive. Installation & Operator s Instruction Manual
TURBO Fiberglass Cone Fan and Grill Fan 48'' Belt Drive Installation & Operator s Instruction Manual July 1998 MV1383B Chore-Time TURBO TM Fan Extended Warranty Chore-Time Equipment warrants new TURBO
More informationE-CDR48-PL-0413 REVISED STARTING SERIAL # PARTS LIST MANUAL 48 CORE DRILL RIGS. EdcoParts.com
E-CDR48-PL-0413 PARTS LIST MANUAL 48 CORE DRILL RIGS REVISED STARTING SERIAL # 130410266 EdcoParts.com SKU # MODEL # VACUUM PUMP DRILL MOTOR SPEED/RPM 97100EV 4820 INCLUDED MILWAUKEE DYMO DRILL 2 SPEED
More informationOperating Instructions (ENG) MODEL: AM115V. Read instructions before operating the machine. AM /24/00
Operating Instructions (ENG) MODEL: AM115V Read instructions before operating the machine. A AM 98710 03/24/00 THIS PAGE LEFT BLANK INTENTIONALLY 1 MACHINE DATA LOG/OVERVIEW MODEL DATE OF PURCHASE SERIAL
More informationOWNER'S MANUAL IMPORTANT: READ OWNER'S MANUAL CAREFULLY MODEL : CHEETAH DC2000 FOR YOUR CONVENIENCE, RECORD THE FOLLOWING IMPORTANT INFORMATION MODEL:
OWNER'S MANUAL IMPORTANT: READ OWNER'S MANUAL CAREFULLY MODEL : CHEETAH DC2000 FOR YOUR CONVENIENCE, RECORD THE FOLLOWING IMPORTANT INFORMATION MODEL: SERIAL NUMBER:-------- DATE PURCHASED: PURCHASED FROM:
More informationCanister Vacuums S6EVO. Operations and Parts Manual. Models: S6EVO
Canister Vacuums S6EVO Operations and Parts Manual Models: S6EVO 2 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ
More informationJOB EXTRACTOR OPERATIONS MANUAL REV A
JOB EXTRACTOR OPERATIONS MANUAL REV A October 2002 OPERATOR SAFETY INSTRUCTIONS WARNING DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and
More informationMK-SINGLE DISC GRINDER OWNERS MANUAL PARTS LIST & OPERATING INSTRUCTIONS
www.mkdiamond.com MK-SINGLE DISC GRINDER OWNERS MANUAL PARTS LIST & OPERATING INSTRUCTIONS SDG-3 Revision 202 11.2011 SDG-11 Manual 158273 Caution: Read all safety and operating instructions before using
More informationGP-6 Cabmaker Owner s Manual and Operating Instructions
GP- Cabmaker Owner s Manual and Operating Instructions Belts Model: Part# 80008 Diamond Pads Model: Part# 80005 Carbide Wheel Model: Part# 8000 Revision 05 0.08 Manual Part No. 597 Caution: Read all safety
More informationFM-ME EDGER/SCRUBBER FLOOR MACHINE. Model: PARTS & OPERATING MANUAL
FM-ME EDGER/SCRUBBER FLOOR MACHINE Model: 515451 PARTS & OPERATING MANUAL Thank you for purchasing a Pacific Floorcare product. Carefully inspect all components for freight damage. If such damage is discovered,
More informationMAXUM 5 5 Gallon Box Extractor
MAXUM 5 5 Gallon Box Extractor INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS This operator s book has important information for the use and safe operation of this machine. Read this book carefully
More informationElectronic Service Manuals
Electronic Service Manuals This electronic document is provided as a service to our customers. We do not create the contents of the information contained in this document. Should you have detailed questions
More informationWet/Dry Vacuums Polyethylene, Polypropylene, & Steel
Wet/Dry Vacuums Polyethylene, Polypropylene, & Steel Operations and Parts Manual Models: 315P 415P 429P 430P 415S 415ST 415PLT 429ST IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic
More informationSD2000 FLOOR BURNISHER
SD2000 FLOOR BURNISHER OPERATION & PARTS MANUAL REV A April 2003 SPECIFICATIONS Length: 33.75 inches Width: 2 inches Height: 50 inches Weight: 69 pounds Pad Speed: 2000 Pad Diameter: 20 inches Drive Motor:.5
More informationIMAGE V. Parts and Service Manual
IMAGE 0V Section II Parts and Service Manual (88B) CLARKE TECHNOLOGY Image Operator's Manual Page AUTHORIZED PERSONNEL MAINTENANCE To Access Pump Motor. Remove brush housing from machine. See "Brush Motor
More informationWET/DRY VACUUM. QUEST for Continuous Improvement Windsor s Quality Management System is Certified ISO MODEL: T1. Operating Instructions (ENG)
WET/DRY VACUUM Operating Instructions (ENG) MODEL: T1 y QUEST for Continuous Improvement Windsor s Quality Management System is Certified ISO 9001. Read these instructions before operating the machine.
More informationUser s Manual and Operating Instructions
User s Manual and Operating Instructions Model Numbers: CL-36-BDF-A, CL-42-BDF-A, CL-48-BDF-A READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Read and understand all of the directions in this manual before
More informationINTELLI-VAC 14 INTELLI-VAC 18
INTELLI-VAC 14 INTELLI-VAC 18 INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS This operator s book has important information for the use and safe operation of this machine. Read this book carefully before
More information48 Vanguard Belt Drive Fans Installation and Operators Instruction Manual
8 Vanguard Belt Drive Fans Installation and Operators Instruction Manual Thank You The employees of Chore-Time Equipment would like to thank your for your recent Chore-Time purchase. If a problem should
More informationMK-1080 PAVER SAW OWNER S MANUAL & PARTS MANUAL
www.mkdiamond.com OWNER S MANUAL & PARTS MANUAL Revision 106 03.2019 Manual Part No. 166894 Caution: Read all safety and operating instructions before using this equipment. This manual MUST accompany the
More informationOperations and Parts Manual
Canister Vacuums Hospital Vac Operations and Parts Manual Models: S9HOSPITAL 2 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the
More informationPACER 30 VACUUM IMPORTANT SAFETY INSTRUCTIONS READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE OPERATING OR SERVICING MACHINE
DANGER! PACER 30 VACUUM IMPORTANT SAFETY INSTRUCTIONS READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE OPERATING OR SERVICING MACHINE Failure to Observe These Instructions Can Cause Fire, Electrical Burn, Shock
More informationSSS BPV- 40 Backpack Vacuum
SSS BPV- 40 Backpack Vacuum Manual The contents of this manual are based on the latest product information available at the time of publication. Triple S reserves the right to make changes or improvements
More informationMAXUM Gallon Box Extractor
MAXUM 12 12 Gallon Box Extractor INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS This operator s book has important information for the use and safe operation of this machine. Read this book carefully
More information225FPCF Operator s Manual
Floor Polisher 225FPCF Operator s Manual FOR YOUR SAFETY DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Record This Important Information
More informationE-1 EDGER POLISHER/SCRUBBER
E-1 EDGER POLISHER/SCRUBBER INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS READ THIS BOOK This operator s book has important information for the use and safe operation of this machine. Read this book
More information48 Vanguard Belt Drive Fans Installation and Operators Instruction Manual
8 Vanguard Belt Drive Fans Installation and Operators Instruction Manual Thank You The employees of Chore-Time Equipment would like to thank your for your recent Chore-Time purchase. If a problem should
More informationSEARAY LOW MOISTURE POLISHER/SCRUBBER OPERATING & MAINTENANCE
SEARAY LOW MOISTURE POLISHER/SCRUBBER INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS This operator s book has important information for the use and safe operation of this machine. Read this book carefully
More informationCRV Clean Room Vacuum
CRV Clean Room Vacuum Model: C80704-01, 02 SS (115V) C80704-03, 04 Painted (115V) C80704-07, 12 Painted (240V) C80704-08, 09 SS (240V) OPERATION SERVICE PARTS CARE Revised 7/02 FOR COMMERCIAL USE ONLY
More information6-Gallon Carpet Extractor Series
Limited Warranty CleanFreak warrants new equipment against defects in material and workmanship under normal use and service to the original purchaser. Any statutory implied warranties, including any warranty
More informationBUNN H5E H5M H5X BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS PHONE: (217) FAX: (217)
! BUNN DISCONNECT FROM POWER SOURCE BEFORE REMOVAL OF ANY PANEL OR REPLACEMENT OF ANY COMPONENT! WARNING H5E H5M H5X WARNING Very Hot Water Use With Care!! ILLUSTRATED PARTS CATALOG Designs, materials,
More informationMODEL NO CRIMPING AND BEADING MACHINE OPERATION, PARTS & MAINTENANCE MANUAL
MODEL NO. 0581 CRIMPING AND BEADING MACHINE OPERATION, PARTS & MAINTENANCE MANUAL Model: Serial #: Purchased From: Date Received: FOREWORD This manual has been prepared for the owner and operators of Roper
More informationTABLE OF CONTENTS
TABLE OF CONTENTS Safety Precautions Machine Operation Machine Maintenance & Storage Handle Release Assembly Instructions Parts Lists Wiring Diagram Warranty Policy 3 4 4 5 6-10 11 12-2- SAFETY PRECAUTIONS!!!
More informationDISCARD DECANTER IF: FAILURE TO COMPLY RISKS INJURY FUNNEL CONTENTS ARE HOT ILLUSTRATED PARTS CATALOG
! GMB-PS WARNING Disconnect from power source before removal of any panel or replacement of any component! FUNNEL CONTENTS ARE HOT CAUTION DISCARD DECANTER IF:. CRACKED. SCRATCHED. BOILED DRY. HEATED WHEN
More information36 & 48 E-Z Cone Fan. Installation & Operator s Instruction Manual (Direct Drive)
36 & 48 E-Z Cone Fan Installation & Operator s Instruction Manual (Direct Drive) September 1997 MV1433C Chore-Time Warranty Chore-Time Equipment warrants each new product manufactured by it to be free
More informationSSS Intrepid 16 FMS. Manual
SSS Intrepid 16 FMS Manual The contents of this manual are based on the latest product information available at the time of publication. Triple S reserves the right to make changes or improvements to its
More informationModel PF 2030 Wide Area Vacuum Cleaner
Model PF 2030 Wide Area Vacuum Cleaner OPERATING INSTRUCTIONS COMMERCIAL WIDE AREA SWEEPER VACUUM CONGRATULATIONS YOU HAVE JUST ACQUIRED A HIGH QUALITY VACUUM CLEANER. PLEASE READ THIS MANUAL CAREFULLY,
More informationGetz Equipment Innovators 450 lb Dual Portable Dry Chemical Fill System
Getz Equipment Innovators 450 lb Dual Portable Dry Chemical Fill System 1 Revised 11/18/10 2320 Lakecrest Drive, Pekin IL 61554 PH. (888) 747-4389 Fax (309) 495-0625 Website: www.getzequipment.com LIMITED
More informationMK-2000 GAS SERIES MASONRY SAW
www.mkdiamond.com MK-000 GAS SERIES MASONRY SAW Parts List MODELS part # MK-00H MK-00V MK-00K MK-00G Revision 0 0.0 Manual Part No. 0-PM Caution: Read all safety and operating instructions before using
More informationWET/DRY VACUUMS POLYETHYLENE, POLYPROPYLENE & STEEL
WET/DRY VACUUMS POLYETHYLENE, POLYPROPYLENE & STEEL MODELS: 315P 415P 429P 415S 415ST 415PLT 429ST OPERATIONS AND PARTS MANUAL IMPORTANT READ THIS MANUAL PRIOR TO USE. TABLE OF CONTENTS Page No. Important
More informationInstruction Manual. Astro Staging Cabinet
Instruction Manual Astro Staging Cabinet 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 2017 Gold Medal Products Co. Part No. 40269 SAFETY PRECAUTIONS DANGER Machine must be properly grounded to
More informationSTAND ALONE DRYER BASE. Parts Manual
STAND ALONE DRYER BASE Parts Manual TABLE OF CONTENTS DRYER BASE SYSTEM DRYER BASE SYSTEM ASSEMBLY (FIG. 1) 3 FRAME ASSEMBLY (FIG. 2). 5 CONVEYOR DRIVE ASSEMBLY (FIG. 3)...7 IDLER SHAFT / TENSIONER ASSEMBLY
More informationMRS-6 Maxi-Guard II. Model: C , 12, 13, 14 OPERATION SERVICE PARTS CARE. Revised 2/02
MRS-6 Maxi-Guard II Model: C86006-11, 12, 13, 14 OPERATION SERVICE PARTS CARE Revised 2/02 OPERATING INSTRUCTIONS INSPECTION Carefully unpack and inspect your machine for shipping damage. Each unit is
More informationGENIUS 14 GENIUS 18 OPERATING & MAINTENANCE
GENIUS 14 GENIUS 18 INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS This operator s book has important information for the use and safe operation of this machine. Read this book carefully before starting
More information20-GALLON PARTS WASHER OWNER S MANUAL
20-GALLON PARTS WASHER OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious
More informationSINGLE BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS PHONE: (217) FAX: (217)
! SINGLE WARNING DISCONNECT FROM POWER SOURCE BEFORE REMOVAL OF ANY PANEL OR REPLACEMENT OF ANY COMPONENT! PRIOR TO S/N SNG000000 gal gal gal START ON / WARMER SELECTOR READY! BUNN MANUFACTURED BY BUNN-O-MATIC
More informationA HEATER KIT With Diesel Engine Connection Fittings
A-12142 HEATER KIT With Diesel Engine Connection Fittings Figure 1 (General Layout and Parts I.D.) Page 1 of 6 Read these instructions and identify all components. Please retain these instructions for
More informationDISCARD DECANTER IF: FUNNEL CONTENTS ARE HOT FAILURE TO COMPLY RISKS INJURY
! BUNN GMB-PS WARNING Disconnect from power source before removal of any panel or replacement of any component! FUNNEL CONTENTS ARE HOT CAUTION DISCARD DECANTER IF:. CRACKED. SCRATCHED. BOILED DRY. HEATED
More informationFIBERPRO SPOTTER CARPET. 3.5 Gallon Carpet Spotter Machine. Operator and Parts Manual E
E85509-00 FIBERPRO SPOTTER CARPET 3.5 Gallon Carpet Spotter Machine Operator and Parts Manual 1001 Brown Avenue Toledo, Ohio 43607-0127 Customer Service: 888-GO-BETCO Fax: 800-445-5056 Technical Service:
More informationOperator and Parts Manual Nu-1600 Burnisher, Belt Drive Nu-2000 Burnisher, Belt Drive
Operator and Parts Manual Nu-1600 Burnisher, Belt Drive Nu-2000 Burnisher, Belt Drive NuSource Enterprises, LLC; A 4699 61 st St. Suite C; Holland, MI 49423 Length 33.75 in. Width 21 in. Height 50 in.
More informationParts and Instruction Manual ET Extraction Tool
Parts and Instruction Manual ET Extraction Tool This manual is furnished with each new MINUTEMAN ET Extraction Tool. This provides the necessary operating and preventive maintenance instructions. Operators
More informationCL & CLG Clamp Mount Mixers
CL & CLG Clamp Mount Mixers CL / CLG Series OWNERS MANUAL Warranty Our products are guaranteed against defective materials and workmanship, we will repair or replace such items as may prove defective at
More informationFM-ME EDGER/SCRUBBER FLOOR MACHINE
PARTS & OPERATING MANUAL FM-ME EDGER/SCRUBBER FLOOR MACHINE PLEASE READ THIS BOOK This operator s book has important information for the use and safe operation of this machine. Read this book carefully
More informationModel: PS-2 ProSense II Item # OPERATION SERVICE PARTS CARE
Model: PS-2 ProSense II Item # 49001 OPERATION SERVICE PARTS CARE FOR COMMERCIAL USE ONLY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed,
More information5HP CYCLONE DUST COLLECTOR MANUAL
5HP CYCLONE DUST COLLECTOR MANUAL LAGUNA TOOLS 2072 Alton Parkway Irvine, California 92606 Ph: 800.234.1976 www.lagunatools.com 2018, Laguna Tools, Inc. LAGUNA and the LAGUNA Logo are the registered trademarks
More information14 Upright Vacuum with HEPA Filter & Dual Power
E29990-00 14 Upright Vacuum with HEPA Filter & Dual Power Operator and Parts Manual 1001 Brown Avenue Toledo, Ohio 43607-0127 Customer Service: 888-GO-BETCO Fax: 800-445-5056 Technical Service: 877-856-5954
More informationGULPER 16SV 16 GALLON WET/DRY VACUUM WITH FRONT MOUNT SQUEEGEE
GULPER 16SV 16 GALLON WET/DRY VACUUM WITH FRONT MOUNT SQUEEGEE INTRODUCTION OPERATING & MAINTENANCE INSTRUCTIONS This operator s book has important information for the use and safe operation of this machine.
More information7165 Dust Collector Owner s Manual
7165 Dust Collector Owner s Manual Oliver Machinery M-7165 12/2016 Seattle, WA Copyright 2003-2017 info@olivermachinery.net www.olivermachinery.net CONTENTS IMPORTANT SAFETY RULES----------------------------------------------------------------
More informationSPA BLOWER OWNER'S MANUAL XXXX, XXXX, XXXX, XXXX, XXXX, XXXX fax
SPA BLOWER OWNER'S MANUAL 80015-XXXX, 80016-XXXX, 80017-XXXX, 80018-XXXX, 80019-XXXX, 80020-XXXX fax 888.610.3839 2015 323300-015 6/15 THIS PAGE INTENTIONALLY LEFT BLANK. 2 Operating Instructions and Parts
More informationBIOCIDE ANTIMICROBIAL DRY VACUUM
BIOCIDE ANTIMICROBIAL DRY VACUUM Model: ATIBCV IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS
More information55-Gallon Dispenser Package
INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. 308 666 Rev. A Husky 715 55-Gallon Dispenser Package 100 psi (6.9 bar) Maximum
More informationBG6UL. 6 Inch Bench Grinder Assembly & Operating Instructions
BG6UL 6 Inch Bench Grinder Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important information
More informationIMPORTANT SAFETY INFORMATION
OPERATION INSTALLATION PARTS MANUAL www.fostoriaindustries.com Made in U.S.A. ELECTRIC PORTABLE HEATER FES-1024-1CA 08860010 YES-1024-1CA 08861510 FES-1520-3A 08860110 YES-1520-3A 08860810 FES-1524-1A
More informationBUNN CWT-CS CWTF-CS BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS PHONE: (217) FAX: (217)
BUNN CWT-CS CWTF-CS ILLUSTRATED PARTS CATALOG Designs, materials, weights, specifications, and dimensions for equipment or replacement parts are subject to change without notice. BUNN-O-MATIC CORPORATION
More informationELECTRIC FIREPLACE HEATER WITH SINGLE GLASS DOOR
ELECTRIC FIREPLACE HEATER WITH SINGLE GLASS DOOR Model 91797 ASSEMBLY and Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure
More informationMK-100 JCS Tile Saw TILE SAW OWNER S MANUAL & OPERATING INSTRUCTIONS SERIAL NUMBER:
MK-00 JCS Tile Saw TILE SAW OWNER S MANUAL & OPERATING INSTRUCTIONS CAUTION: Read all safety and operating instructions before using this equipment Enter the Serial Number of your new saw in the space
More informationOperator s Manual MODEL 400A Hydra-Lift, 60, Air Power Lift & Manual Tilt. for Morse Hydra-Lift Drum Karrier Model 400A
Contents Page Receiving Procedures................. 1 Warranty............................... 1 Safety Information..................... 1-2 Machine Description................... 3-4 Operating Instructions...................
More informationVENTURI AIR SPRAYERS
VENTURI AIR SPRAYERS Parts Manual For Model P45N1-400-G 3-Point Mount Form: P45N400GBookRev2012.indd June 2012 (Rev.) TABLE OF CONTENTS SECTION DESCRIPTION... PAGE 1 Introduction... 1 1.1 Purchaser s Responsibility...
More informationMK-MANTA III OWNER S MANUAL PARTS LIST & OPERATING INSTRUCTIONS
www.mkdiamond.com MK-MANTA III OWNER S MANUAL PARTS LIST & OPERATING INSTRUCTIONS Revision 06 0.07 Manual Part# 67 Caution: Read all safety and operating instructions before using this equipment. This
More informationMN908 No. 282C Replaces 282B LB7013
No. 282C Replaces 282B LB7013 Instruction Manual For Baldor Dust Control Units Models DC7, DC7 3, DC8, DC8 3, DC10, DC10 3, DC12, DC12 3 and DC14 3. For use on Grinders mounted to GA16 and GA20 pedestals
More informationModel 2016, 2025, 2025BN, 2025ST Staging Cabinets Instruction Manual
Model, 2025BN, 2025ST Staging Cabinets Instruction Manual Part No 53021 Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS DANGER Machine must be properly grounded to prevent electrical shock to personnel.
More informationMODEL # PUMA G, 3-SPEED TRANSPORTABLE AIR MOVER
OWNER S MANUAL IMPORTANT: READ OWNER S MANUAL CAREFULLY MODEL # PUMA G, 3-SPEED TRANSPORTABLE AIR MOVER FOR YOUR CONVENIENCE, RECORD THE FOLLOWING IMPORTANT INFORMATION MODEL: SERIAL NUMBER: DATE PURCHASED:
More informationInstruction Manual. Cheddar Easy All-In-One Cheese Corn Shop
Instruction Manual Cheddar Easy All-In-One Cheese Corn Shop Model No. 2703-00-000 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 2017 Gold Medal Products Co. Part No. 110028 SAFETY PRECAUTIONS
More information