Steam Room Installation Manual L52 Series (L528) All set up dimensions are in Millimeters

Transcription

1 Steam Room Installation Manual L52 Series (L528) All set up dimensions are in Millimeters

2 L528 Steam Room structure Size:1400x940x2260mm A GFCI Circuit Cold Water Hot Water Plane Diagram 550 Three Dimensional Installation Diagram 01. Water Supply : one hot water pipe and one cold water pipe, Install the DN15(G1/2) shut-off valve 1000mm from the floor, 0.15Mpa Water Pressure 0. 4MPa. 02. Power Supply : Steam Generator Power : 4000W, Rated Voltage : AC220V~ 240V / 50~60Hz, Single-phase three-wire 3x4mm² copper insulated wire, Independent electrocircuit, install only GFCI breakers with a reliable ground wire protection, Install the 30A GFCI circuit at the 1500mm wall height to connect the steam generator circuit. 200 No. Components No. Components No. Components No. Components 1 Fan 8 Active Glass 15 Top Shower 22 Steam Box 2 Top Track 9 Shower Chain 16 Speaker 3 Handheld Shower 10 Acupuncture Jet 4 Edge Aluminum 11 Seat Colorful Top Light Storage Shelf 5 Mirror 12 Foot Massage 19 Scotland Waterfall 6 Sliding Bar 13 Bottom Track 20 Changeover Switch 7 Fixed Glass 14 Top Cover 21 Control Panel Water Drainage : the Floor drain outlet should be DN50 (2 inch), keep the same level as the ground. 04. Models with a telephone and CD, install the telephone and CD socket above the power socket. Installation Requirement First check the package factory code marked on crates. Numbers should match. Second prepare the following tools : phillips screwdriver, slotted screwdriver,6~30# adjustable wrench,level,knife, silicone sealant, caulk gun,wood wedge, plastic hammer. 2

3 Installation Steps Silicone M6x35mm Plastic washer Pic1 1. Install Tray Move the Tray to the desired location, every ground foot nut should touch the ground, Use the leveling feet to level the tub. Insert the drain pipe into the drainage outlet. Drain should be a minimum of 2 inch dia. Refer to Pic 1 Clear Silicone Pic3 (2) line up the mid back panel holes to bathtub holes. Use M6x35 hexagon screws to connect( As Pic 3) Leave all hardware loose until unit is completely assembled. (3) Apply silicone along the mid back panel left edge. (As Pic 3) (4)Glue plastic washer to the left panel installation hole. Apply silicone continually along the installation holes. ( As Pic 2) (5) Use M6x25 hexagon screws to connect the Left panel to mid back panel holes. Use M6x35 hexagon screws to connect the Left panel to tray holes.(as Pic 4) (6) Use the same method to install the Right Panel.(As Pic 5) M6x25 Right-Panel Pic2 Glue down plastic washer M6x35mm Plastic washer 2.Install Mid back panel / Left Panel / Right Panel (1)Glue plastic washer to every mid back panel installation hole. Apply silicone continually along the installation holes (As Pic2 ) 3 Pic4 4 Pic5

4 3.Install Aluminum Frame (1) Insert the Left fix glass and Right fix glass into left panel and right panel ( As Pic 6) Left Fix Glass Right-Panel Right Fix Glass 4. Install Cover Put the top cover on the roof (1)Align the left panel and right panel holes, use the M6x25 hexagon screws to connect them. (2)Align the glass door frame,left panel and right panel holes,use selftapping screws to connect them(as Pic 8) M6x25 Pic6 (2) Set the glass door frame between the left fix glass and right fix glass. (As pic 7) (3) Align the glass door frame holes to the left fix glass and right fix glass holes, then use the self-tapping screws to connect them. (As pic 7) (4) After glass door frame cline to the fix glass, then in the inner of glass door frame, use the M4x10 self-tapping screws to fix the glass door frame aluminum, then install the screws caps. (As pic 7) Pic8 Left Fix Glass Right Fix Glass Shower Sliding Bar M4x10 Pic7 Pic9 4. Install parts: Install the handheld shower, steam box, storage shelf, foot massage and so on to the steam room corresponding holes. (As Pic 9) 5 6

5 5. Install the pipe (As Water ion Diagram) Waterfall Handheld Shower Hot Water Top Shower Steam Generator Water in Cold Water Steam Generator Waterfall Foot Massage Steam Box Electromagnetic Valve Steam Generator Water out Drain Outlet 6. Electrocircuit Speaker, exhaust fan, and ozone and so on. 7.Sealing the shower chamber Apply clear silicone to all seams and gaps. 8. Test After finishing installation, connect the water and electrical supply. Make sure the steam room and bathtub function properly, with no leaks. 7 8