CADB/T-D DP25 F7 Series CADB/T-DI DP25 F7 CADB/T-DC DP25 F7. Heat recovery units CADB/T-D

Transcription

1 CONFIGURLE cross-flow heat RECOVERY DP25 F7 Series I DP25 F7 C DP25 F7 housed in galvanised steel boxes, white plastic coated, with a 25 mm thick double wall, class M0 fire proof thermal and acoustic insulation, configurable inlets and outlets, versions for horizontal installation and for vertical installation, intakes with a hermetic seal, F7 filter for inlet air and G4 filter for air extraction. With two double inlet centrifugal fans with builtin motor. DP25 F7 Series Heat recovery without additional heat added. I DP25 F7 Series Heat recoveries with a heating resistance. C DP25 F7 Series Heat recoveries with a built-in hot water coil. Motors IP20, Class F (ranges 05, 08, 18 and 30). IP55, class F (ranges 45 and 56). IMPORTNT UPDTE TO THE RNGE New standard configuration with a 25 mm thick double wall and F7 filters with low loss of load, manufactured in polypropylene, for inlet air and G4 manufactured in fibreglass for extraction. dditional information Single phase (CD) and three phase models (CDT). Flows from 450 to 5,600 m 3 /h. Versions with an electronic microprocessor (SIC, PROGRM, DVNZ or DOMO) that enables the fan speed to be controlled. The versions with an electronic microprocessor in sizes 45 and 56 also incorporate a variable frequency drive. Horizontal and vertical versions, both with the possibility of a by-pass. ll side panels are interchangeable, which makes it possible to directly position the intake and outtake connections on site. P P L I C T I O N S Stores Offices Cafes, bars and restaurants Collective ventilation dwellings

2 Structural dvantages Vertical construction Low noise level Easy to mount Version with by pass Specific models for vertical installation. Internally lined with 25 mm M0 fire resistant acoustic insulation. Single phase models integrated hanging supports to install the heat recovery unit. Versions with by pass enabling 100% of the air to by pass the heat recovery (65% in singlephase versions). The by-pass works with a remotely activated servomotor with a manual switch (not included). 2 high-efficiency filters irtight connectors Robust construction Condensation drain 2 filters: F7 filter for inlet air (filtration efficiency: >80%). G4 filter for extracted air (efficiency: >90%). Pressure sockets Inlet and discharge circular duct connection flanges with integrated rubber air seal. External weatherproof terminal box High quality finishing with aluminium profile structure, providing a robust assembly. Drain pipe to evacuate water from condensation. Versions CD-D/DC/DI Regulation with an electronic microprocessor Pressure sockets before for clogging filter control. IP55 terminal box located on the outside of the heat recovery casing for easy wiring access. SIC PROGRM DVNZ DOMO Versions that incorporate an electronic microprocessor (SIC, PROGRM, DVNZ or DOMO) that enables fan speed control. The versions with an electronic microprocessor in sizes 45 and 56 also incorporate a variable frequency drive.

3 Structural dvantages Versatile assembly The design of these heat recovery units makes it possible for the user to configure them on site. ll side panels are interchangeable, which makes it possible to directly position the intake and outtake connections on site depending on the specific requirements. ll side panels are interchangeable

4 Structural dvantages Easy maintenance s CD- 05 / 08 / 18 / 30: Rapid access to the filters from the bottom and sides. Easy access for cleaning the heat recovery from the bottom. s CDT-45 and CDT-56: Rapid access to the filters from the top. It is also possible to access from the side and bottom. Easy access for cleaning the heat recovery from the top. Reference C D - D I 3 0 H T R I P D P 2 5 F 7 S I C V V CD / CDT: Series 2 - D: Standard range DI: Range with resistance incorporated DC:Range with water coil incorporated 3 - Size 4 -,, C, D, E, G, H: Type of configuration 5 - H: Horizontal unit V: Upright unit. 6 - MONO: Monophase support resistance. TRI: Three phase support resistance 7 - P: Version with by pass incorporated 8 - DP: Range with double wall insulation (25 mm). 9 - F7: ir inlet filter F SIC, PROGRM, DVNZ, DOMO Control Configuration control VV - Variable airflow CV - Constant airfflow (sizes 45 and 56) (Not posible with SIC) COP - Constant pressure (sizes 45 and 56) (Not possible with SIC)

5 Versions with an electronic microprocesor: s and functions SIC PROGRM DVNZ DOMO 1 Manual fan speed selection: OFF + 3 speed Manual fan speed selection: OFF + control of speed range [MIN-MX] (alternative to 1 ) Imbalance between impulsion and extraction flow only for VV versions with double inverter (does not apply to 3 speed versions) utomatic control of fan speed: CO 2, CO 2 /VOC and HR sensors with programmable PPM or HR range (by the installer); available for 3 speed versions and variable speed versions Remote function of the fan speed signal is 0-10V (alternative to 4 ) ooster via remote NC contact at a pre-set time. Time can be altered by software Remote "oost" management by NC contact or proximity sensor (alternative to 6 and 8 ) Unit can be switched ON/OFF via remote switch (alternative to 6 or 7 ) Weekly programs Prevention of icing of the heat exchanger (simple strategy): blower fan moves to low/off; Setting the extractor fan to maximum speed Prevention of build-up of frost in the heat exchanger: proportional mode management with pre-heating coils (alternative to 10 or 12 ) Exchanger frost prevention: Personalized funcions (through a switch NO-NC (alternative to 10 and 11 ) Management of electric post-heating (simple or double stage) in ON/OFF mode. The objective is to attain the average internal temperature value (Tr) 3 14 Management of electric post-heating in proportional mode. The objective is to attain the average internal temperature value (Tr) and to keep the impelled air within a set range (Ti) Management of water coil post-heating in ON/OFF mode. The objective is to attain the average internal temperature value (Tr) 3 16 Management of water coil post-heating. The objective is to attain the average internal temperature value (Tr) and to keep the impelled air within a set range (Ti) Management of post-cooling in proportional mode. The objective is to attain the average internal temperature value (Tr) and to keep the impelled air within a set range (Ti) Remote signalling of the status of the unit via a volt free contact: closed contact=the unit is operating; open contact=the unit is stopped (alternative to 12 ) Monitoring of the state of the filters via period of operation of the equipment or via differential pressure sensors Monitoring of the state of the fans via a tachometric signal (if supported by the fan) or via differential pressure sensors

6 Electronic microprocessors SIC model - Features and functions SIC CONTROL PRINCIPL FETURES Terminal cabinet includes: Proximity sensor Integrated circuit card and terminal box Remote control unit (100 m max.) Ready-mounted, ready-wired temperature sensors: Discharge temperature sensor (Tx) New air intake temperature sensor (Te) mbient air return temperature sensor (Tr) Vacuum regulator valve, ready-mounted and wired: Filter clogging Frequency regulator on Three phase models (sizes 45 and 56) OPTIONL FETURES Vacuum regulator valve, ready-mounted and wired: E-SCT circular battery Differential pressure switch Timer TG-K310 duct-mountable temperature sensor -20 to + 10ºC TI-10 potentiometer -20 to + 10ºC for panel mounting FUNCTIONS Flow rate adjustment: Manual fan speed selection: - Single phase models: 3 speed - Three phase models: 45%, 65% and 100% of maximum flow rate Free cooling function on models equipped with by-pass Prevention of icing of the heat exchanger: Heat exchanger antifreeze protection (blower fan moves to low/off) Safety functions: Filter clogging / vacuum regulator valve failure alarm Temperature sensor fault alarm (wire severed, connection fault,...) Console-control cabinet connection fault alarm Included, Unmounted option Schematic diagram CDT/T-D DP25 F7 with SIC control T discharge T new air intake Self-regulating antifreeze battery + y-pass T return (ambient) 0/VL/VM/VR SIC The battery is regulated independently. The SIC can not control it. oost HS/LS larms HS: High speed LS: Low speed

7 Electronic microprocessors - PROGRM model - Features and functions PROGRM CONTROL PRINCIPL FETURES Terminal cabinet includes: Proximity sensor Integrated circuit card and terminal box Remote control unit (100 m max.) Ready-mounted, ready-wired temperature sensors: Discharge temperature sensor (Tx) New air intake temperature sensor (Te) mbient air return temperature sensor (Tr) Vacuum regulator valve, ready-mounted and wired: Filter clogging Security (operation of fans) Frequency regulator on three phase models (sizes 45 and 56) OPTIONL FETURES CO2 sensor: SCO2-010 ambient sensor with display / SCO2-010G in-duct measurement Self-regulating antifreeze battery: E-SCT circular battery Differential pressure switch Timer TG-K310 duct-mountable temperature sensor -20 to + 10ºC TI-10 potentiometer -20 to + 10ºC for panel mounting FUNCTIONS Flow rate adjustment: Manual fan speed selection (single phase models) or variable (three phase models 45/56). Timer boost function utomatic modulation via built-in clock: daily and weekly programs utomatic speed settings (single phase models) or automatic speed variation (Three phase models) based on air quality sensor readings (sensor optional) Operates at constant pressure * Free cooling function on models equipped with by-pass Safety functions: Heat exchanger antifreeze protection (blower fan moves to low/off) Filter clogging / vacuum regulator valve failure alarm Temperature sensor fault alarm (wire severed, connection fault,...) Console-control cabinet connection fault alarm Included, Unmounted option * Optional and on request in 45 and 56 models Schematic diagram I DP25 F7 with PROGRM control T discharge T new air intake Self-regulating antifreeze battery + PROGRM CONTROL I C PRINCIPL FETURES Terminal cabinet includes: Proximity sensor Integrated circuit card and terminal box Remote control unit (100 m max.) Ready-mounted, ready-wired temperature sensors: Discharge temperature sensor (Tx) New air intake temperature sensor (Te) mbient air return temperature sensor (Tr) Supply air temperature sensor (Ti) Vacuum regulator valve, ready-mounted and wired: Filter clogging Security (operation of fans) Frequency regulator on three phase models (sizes 45 and 56) OPTIONL FETURES Motorized 3-way control valve + 230V/24V transformer for - hot water coil CO2 sensor: SCO2-010 ambient sensor with display / SCO2-010G in-duct measurement Self-regulating antifreeze battery: E-SCT circular battery Differential pressure switch Timer TG-K310 duct-mountable temperature sensor -20 to + 10ºC TI-10 potentiometer -20 to + 10ºC for panel mounting FUNCTIONS Flow rate adjustment: Manual fan speed selection (single phase models) or variable (three phase models 45/56). Timer boost function utomatic modulation via built-in clock: daily and weekly programs utomatic speed settings (single phase models) or automatic speed variation (Three phase models) based on air quality sensor readings (sensor optional) Operates at constant pressure * * Post heating battery regulation attery power regulation as per temperature setting and blower sensor reading Free cooling function on models equipped with by-pass Safety functions: Heat exchanger antifreeze protection (blower fan moves to low/off) Fan shutdown timer setting for cooling electric battery - (postventilation) Water coil antifreeze protection antigel de la batterie eau in each - sensor (opens 3-way control valve then stops power unit) Filter clogging / vacuum regulator valve failure alarm Temperature sensor fault alarm (wire severed, connection fault,...) Ventilation fault alarm Console-control cabinet connection fault alarm Included, - Not included, Unmounted option * Optional and on request in 45 and 56 models C DP25 F7 with PROGRM control T discharge + T new air intake Self-regulating antifreeze battery* + T supply air 0/HS/MS/LS y-pass PROGRM T return (ambient) T supply air 0/HS/MS/LS y-pass PROGRM T return (ambient) The battery is regulated independently. The PROGRM can not control it. CO2 Sensor Programmable timer oost HS/ Off HS/LS Setpoint adjustment larms CO2 Sensor Programmable timer oost HS/ Off HS/LS Setpoint adjustment larms HS: High speed MS: Medium speed LS: Low speed The battery is regulated independently. HS: High speed MS: Medium speed LS: Low speed The PROGRM can not control it.

8 Electronic microprocessors - DVNZ and DOMO models - Features and functions DVNZ ND DOMO CONTROLS PRINCIPL FETURES Terminal cabinet includes: Proximity sensor Integrated circuit card and terminal box Remote control unit (100 m max.) (Only DVNZ) Ready-mounted, ready-wired temperature sensors: Discharge temperature sensor (Tx) New air intake temperature sensor (Te) mbient air return temperature sensor (Tr) Vacuum regulator valve, ready-mounted and wired: Filter clogging Security (operation of fans) Frequency regulator on three phase models (sizes 45 and 56) OPTIONL FETURES CO2 sensor: SCO2-010 ambient sensor with display / SCO2-010G in-duct measurement Self-regulating antifreeze battery: E-SCT circular battery Differential pressure switch Timer TG-K310 duct-mountable temperature sensor -20 to + 10ºC TI-10 potentiometer -20 to + 10ºC for panel mounting FUNCTIONS Flow rate adjustment: Manual fan speed selection (single phase models) or variable (three phase models 45/56). Timer boost function utomatic modulation via built-in clock: daily and weekly programs utomatic speed settings (single phase models) or automatic speed variation (Three phase models) based on air quality sensor readings (sensor optional) Remote function of the fan speed signal is 0-10V Operates at constant pressure * Free cooling function on models equipped with by-pass Remote "oost" management by NC contact or proximity sensor Remote indication of unit status Exchanger frost prevention: Heat exchanger antifreeze protection (blower fan moves to low/off) Proportional management using an antifreeze battery (pre-heating)) Personalized funcions (through a switch NO-NC) Remote signaling of unit status Panel language configuration (ES/EN/DE/IT/FR) Safety functions: Filter clogging / vacuum regulator valve failure alarm Temperature sensor fault alarm (wire severed, connection fault,...) Console-control cabinet connection fault alarm Communicator regulation [adjustment] (Only DOMO) Included, Unmounted option * Optional and on request in 45 and 56 models Schematic diagram I DP25 F7 with DVNZ / DOMO control Supply air T discharge T new air intake Self-regulating antifreeze battery Register DVNZ ND DOMO CONTROLS I C PRINCIPL FETURES Terminal cabinet includes: Proximity sensor Integrated circuit card and terminal box Remote control unit (100 m max.) (Only DVNZ) Ready-mounted, ready-wired temperature sensors: Discharge temperature sensor (Tx) New air intake temperature sensor (Te) mbient air return temperature sensor (Tr) Supply air temperature sensor (Ti) Vacuum regulator valve, ready-mounted and wired: Filter clogging Security (operation of fans) Solid-state relay on electrical battery - No-frost safety sensor on hot water battery - Frequency regulator on three phase models (sizes 45 and 56) OPTIONL FETURES Motorized 3-way control valve + 230V/24V transformer for hot water coil - CO2 sensor: SCO2-010 ambient sensor with display / SCO2-010G in-duct measurement Self-regulating antifreeze battery: E-SCT circular battery Differential pressure switch Timer TG-K310 duct-mountable temperature sensor -20 to + 10ºC TI-10 potentiometer -20 to + 10ºC for panel mounting FUNCTIONS Flow rate adjustment: Manual fan speed selection (single phase models) or variable (three phase models 45/56). Timer boost function utomatic modulation via built-in clock: daily and weekly programs utomatic speed settings (single phase models) or automatic speed variation (Three phase models) based on air quality sensor readings (sensor optional) Remote function of the fan speed signal is 0-10V Operates at constant pressure * * Post heating battery regulation attery power regulation as per temperature setting and blower sensor reading Free cooling function on models equipped with by-pass Remote "oost" management by NC contact or proximity sensor Remote indication of unit status Exchanger frost prevention: Heat exchanger antifreeze protection (blower fan moves to low/off) Proportional management using an antifreeze battery (pre-heating) Personalized funcions (through a switch NO-NC) Proportional function of post-heating or post-cooling Remote signaling of unit status Panel language configuration (ES/EN/DE/IT/FR) Safety functions: Fan shutdown timer setting for cooling electric battery (postventilation) Water coil antifreeze protection antigel de la batterie eau in each sensor - (opens 3-way control valve then stops power unit) Filter clogging / vacuum regulator valve failure alarm Temperature sensor fault alarm (wire severed, connection fault,...) Console-control cabinet connection fault alarm Communicator regulation [adjustment] (Only DOMO) * Optional and on request in 45 and 56 models C DP25 F7 with DVNZ / DOMO control T supply air T discharge T new air intake Self-regulating antifreeze battery Register T return (ambient) T return (ambient) 0/HS/MS/LS DVNZ DOMO 0/HS/MS/LS DVNZ DOMO Network (DOMO) oost HR CO2 Sensor Programable timer oost HS / Off HS/LS Setpoint adjustment larms Network (DOMO) oost HS CO2 Sensor Programmable timer oost HR / Off HS/LS Setpoint adjustment larms HS: High speed MS: Medium speed LS: Low speed HS: High speed MS: Medium speed LS: Low speed

9 Technical characteristics s without heater Fan type Speed (r.p.m.) Nº of speeds Motor power (kw) Maximum absorbed current motor () Maximum absorbed current total () to 230V to 400V to 230V to 400V Maximum volume (m 3 /h) vailable pressure at maximum airflow (Pa) CD-D 05 DP25 F7 146-HR x 0,150 0,62-1, CD-D 08 DP25 F7 146-HT x 0,355 1,4-2, CD-D 18 DP25 F7 9/ x 0,373 2,75-5, CD-D 30 DP25 F7 10/ x 0, CDT-D 45 DP25 F7 10/ x 0,750-3,1-6, CDT-D 56 DP25 F7 12/ x 1,500-3,9-11, Protection IP s with integrated electrical heater Fan type Speed Nº of speeds Motor power Maximum absorbed current motor () Maximum Maximum absorbed current volume total () Protection IP Efficiency Resist. % power * Resist. voltage Resist. absorbed current (r.p.m.) (kw) to 230V to 400V to 230V to 400V (m 3 /h) (kw) (V) () () CD-DI 05 MONO DP25 F7 146-HR x 0,130 0,62-1, , ,5 9,74 CD-DI 08 MONO DP25 F7 146-HT x 0,310 1,4-2, , ,5 20,3 CD-DI 18 MONO DP25 F7 9/ x 0,373 2,75-5, , ,80 CD-DI 30 TRI DP25 F7 10/ x 0, , ,55 19,59 CDT-DI 45 TRI DP25 F7 10/ x 0,750-3,1-6, ,32 23,52 CDT-DI 56 TRI DP25 F7 12/ x 1,500-3,9-7, , ,32 25,12 * Values referring to the following conditions: Text air = -5ºC, Text exhaust air = +20ºC with RH exhaust air = 80% / max.airflow. Maximum current total fan + resistance s with integrated water coil (water 70/80ºC) Fan type Speed (r.p.m.) Nº of speeds Motor power (kw) Maximum absorbed current motor () Maximum absorbed current total () to 230V to 400V to 230V to 400V Maximum volume (m 3 /h) Protection IP Efficiency Thermal % performance * CD-DC 05 DP25 F7 146-HR x 0,130 0,62-1, ,7 2,62 CD-DC 08 DP25 F7 146-HT x 0,310 1,4-2, ,9 3,67 CD-DC 18 DP25 F7 9/ x 0,373 2,75-5, ,6 10,67 CD-DC 30 DP25 F7 10/ x 0, ,5 14,29 CDT-DC 45 DP25 F7 10/ x 0,750-3,1-6, CDT-DC 56 DP25 F7 12/ x 1,500-3,9-7, ,3 34,5 * Values referring to the following conditions: Text air = -5ºC, Text exhaust air = +20ºC with RH exhaust air = 80% / max.airflow. ** Values referring to the following conditions: water 70/80ºC, intake air temperature +8ºC nominal airflow. (kw) ** Evolution of the efficiency of recovery according to the flow Efficiency CD 05 CD 08 CD 18 CD 30 CDT 45 CDT 56 Values with the following conditions: Outside air temperature -5ºC, inside air temperature +20ºC with interior RH of 80%. irflow (m 3 /h)

10 Thermal efficiency recovery ir volume (m 3 /h) ºC CD-D 05 DP25 F CD-D 08 DP25 F CD-D 18 DP25 F CD-D 30 DP25 F CDT-D 45 DP25 F CDT-D 56 DP25 F T. ambient air T. outdoor air T. air treated H.R. % ºC H.R. % (ºC) Minimum efficiency (%) Power (kw) ,6 52,2 2, ,7 50,7 2, ,4 46,9 1, ,7 44,9 1, ,7 2, ,6 54,4 2, ,5 52,5 1, ,1 47,4 1, ,6 55,4 4, ,5 53,9 3, ,8 2, ,1 47,4 1, ,1 4, ,5 57, ,2 55,8 3, ,5 50,3 2, ,9 53,1 10, ,9 51,6 8, ,5 47,7 6, ,8 45,6 4, ,3 57,7 11, ,8 55, ,7 53,4 6, ,2 48,2 4, , , ,1 52,5 13, ,7 48,5 9, ,9 46,3 7, ,6 58, ,1 56,4 14, ,9 54,4 11, ,4 49,1 7, ,6 55, , , ,1 50,2 15, ,1 47,6 10, ,1 60,3 27, ,8 59,3 22, ,3 56, ,8 51,7 11, ,3 54,5 31, ,1 52,3 25, ,8 48,8 18, ,9 46,1 13, ,5 58,5 34, ,4 57,5 27, ,9 54,5 21, , ,6

11 Complete chart for standard versions HORIZONTL Range 05 CD-D 05 CH DP25 F7 CD-D 05 CH P DP25 F7 Range 08 CD-D 08 CH DP25 F7 CD-D 08 CH P DP25 F7 Range 18 CD-D 18 CH DP25 F7 CD-D 18 CH P DP25 F7 Range 30 CD-D 30 CH DP25 F7 CD-D 30 CH P DP25 F7 Range 45 CDT-D 45 CH DP25 F7 CDT-D 45 CH P DP25 F7 Range 56 CDT-D 56 CH DP25 F7 CDT-D 56 CH P DP25 F7 UPRIGHT Range 05 CD-D 05 V DP25 F7 CD-D 05 V P DP25 F7 Range 08 CD-D 08 V DP25 F7 CD-D 08 V P DP25 F7 Range 18 CD-D 18 V DP25 F7 CD-D 18 V P DP25 F7 Range 30 CD-D 30 V DP25 F7 CD-D 30 V P DP25 F7 Range 45 CDT-D 45 V DP25 F7 CDT-D 45 V P DP25 F7 Range 56 CDT-D 56 V DP25 F7 CDT-D 56 V P DP25 F7 CD-D 05 V DP25 F7 CD-D 05 V P DP25 F7 CD-D 08 V DP25 F7 CD-D 08 V P DP25 F7 CD-D 18 V DP25 F7 CD-D 18 V P DP25 F7 CD-D 30 V DP25 F7 CD-D 30 V P DP25 F7 CDT-D 45 V DP25 F7 CDT-D 45 V P DP25 F7 CDT-D 56 V DP25 F7 CDT-D 56 V P DP25 F7 CD-D 05 HV DP25 F7 CD-D 05 HV P DP25 F7 CD-D 08 HV DP25 F7 CD-D 08 HV P DP25 F7 CD-D 18 HV DP25 F7 CD-D 18 HV P DP25 F7 CD-D 30 HV DP25 F7 CD-D 30 HV P DP25 F7 CDT-D 45 HV DP25 F7 CDT-D 45 HV P DP25 F7 CDT-D 56 HV DP25 F7 CDT-D 56 HV P DP25 F7 I HORIZONTL Range 05 CD-DI 05 H MONO DP25 F7 CD-DI 05 DH MONO DP25 F7 CD-DI 05 EH MONO DP25 F7 CD-DI 05 GH MONO DP25 F7 Range 08 CD-DI 08 H MONO DP25 F7 CD-DI 08 DH MONO DP25 F7 CD-DI 08 EH MONO DP25 F7 CD-DI 08 GH MONO DP25 F7 Range 18 CD-DI 18 H MONO DP25 F7 CD-DI 18 DH MONO DP25 F7 CD-DI 18 EH MONO DP25 F7 CD-DI 18 GH MONO DP25 F7 Range 30 CD-DI 30 H TRI DP25 F7 CD-DI 30 DH TRI DP25 F7 CD-DI 30 EH TRI DP25 F7 CD-DI 30 GH TRI DP25 F7 Range 45 CDT-DI 45 H TRI DP25 F7 CDT-DI 45 DH TRI DP25 F7 CDT-DI 45 EH TRI DP25 F7 CDT-DI 45 GH TRI DP25 F7 Range 56 CDT-DI 56 H TRI DP25 F7 CDT-DI 56 DH TRI DP25 F7 CDT-DI 56 EH TRI DP25 F7 CDT-DI 56 GH TRI DP25 F7 CD-DI 05 H MONO P DP25 F7 CD-DI 05 DH MONO P DP25 F7 CD-DI 05 EH MONO P DP25 F7 CD-DI 05 GH MONO P DP25 F7 CD-DI 08 H MONO P DP25 F7 CD-DI 08 DH MONO P DP25 F7 CD-DI 08 EH MONO P DP25 F7 CD-DI 08 GH MONO P DP25 F7 CD-DI 18 H MONO P DP25 F7 CD-DI 18 DH MONO P DP25 F7 CD-DI 18 EH MONO P DP25 F7 CD-DI 18 GH MONO P DP25 F7 CD-DI 30 H TRI P DP25 F7 CD-DI 30 DH TRI P DP25 F7 CD-DI 30 EH TRI P DP25 F7 CD-DI 30 GH TRI P DP25 F7 CDT-DI 45 H TRI P DP25 F7 CDT-DI 45 DH TRI P DP25 F7 CDT-DI 45 EH TRI P DP25 F7 CDT-DI 45 GH TRI P DP25 F7 CDT-DI 56 H TRI P DP25 F7 CDT-DI 56 DH TRI P DP25 F7 CDT-DI 56 EH TRI P DP25 F7 CDT-DI 56 GH TRI P DP25 F7 UPRIGHT Range 05 CD-DI 05 CV MONO DP25 F7 CD-DI 05 DV MONO DP25 F7 CD-DI 05 EV MONO DP25 F7 Range 08 CD-DI 08 CV MONO DP25 F7 CD-DI 08 DV MONO DP25 F7 CD-DI 08 EV MONO DP25 F7 Range 18 CD-DI 18 CV MONO DP25 F7 CD-DI 18 DV MONO DP25 F7 CD-DI 18 EV MONO DP25 F7 Range 30 CD-DI 30 CV TRI DP25 F7 CD-DI 30 DV TRI DP25 F7 CD-DI 30 EV TRI DP25 F7 Range 45 CDT-DI 45 CV TRI DP25 F7 CDT-DI 45 DV TRI DP25 F7 CDT-DI 45 EV TRI DP25 F7 Range 56 CDT-DI 56 CV TRI DP25 F7 CDT-DI 56 DV TRI DP25 F7 CDT-DI 56 EV TRI DP25 F7 CD-DI 05 CV MONO P DP25 F7 CD-DI 05 DV MONO P DP25 F7 CD-DI 05 EV MONO P DP25 F7 CD-DI 08 CV MONO P DP25 F7 CD-DI 08 DV MONO P DP25 F7 CD-DI 08 EV MONO P DP25 F7 CD-DI 18 CV MONO P DP25 F7 CD-DI 18 DV MONO P DP25 F7 CD-DI 18 EV MONO P DP25 F7 CD-DI 30 CV TRI P DP25 F7 CD-DI 30 DV TRI P DP25 F7 CD-DI 30 EV TRI P DP25 F7 CDT-DI 45 CV TRI P DP25 F7 CDT-DI 45 DV TRI P DP25 F7 CDT-DI 45 EV TRI P DP25 F7 CDT-DI 56 CV TRI P DP25 F7 CDT-DI 56 DV TRI P DP25 F7 CDT-DI 56 EV TRI P DP25 F7 C HORIZONTL Range 05 CD-DC 05 H DP25 F7 CD-DC 05 DH DP25 F7 CD-DC 05 EH DP25 F7 CD-DC 05 GH DP25 F7 CD-DC 05 H P DP25 F7 CD-DC 05 DH P DP25 F7 CD-DC 05 EH P DP25 F7 CD-DC 05 GH P DP25 F7 Range 08 CD-DC 08 H DP25 F7 CD-DC 08 DH DP25 F7 CD-DC 08 EH DP25 F7 CD-DC 08 GH DP25 F7 CD-DC 08 H P DP25 F7 CD-DC 08 DH P DP25 F7 CD-DC 08 EH P DP25 F7 CD-DC 08 GH P DP25 F7 Range 18 CD-DC 18 H DP25 F7 CD-DC 18 DH DP25 F7 CD-DC 18 EH DP25 F7 CD-DC 18 GH DP25 F7 CD-DC 18 H P DP25 F7 CD-DC 18 DH P DP25 F7 CD-DC 18 EH P DP25 F7 CD-DC 18 GH P DP25 F7 Range 30 CD-DC 30 H DP25 F7 CD-DC 30 DH DP25 F7 CD-DC 30 EH DP25 F7 CD-DC 30 GH DP25 F7 CD-DC 30 H P DP25 F7 CD-DC 30 DH P DP25 F7 CD-DC 30 EH P DP25 F7 CD-DC 30 GHP DP25 F7 Range 45 CDT-DC 45 H DP25 F7 CDT-DC 45 DH DP25 F7 CDT-DC 45 EH DP25 F7 CDT-DC 45 GH DP25 F7 CDT-DC 45 H P DP25 F7 CDT-DC 45 DH P DP25 F7 CDT-DC 45 EH P DP25 F7 CDT-DC 45 GH P DP25 F7 Range 56 CDT-DC 56 H DP25 F7 CDT-DC 56 DH DP25 F7 CDT-DC 56 EH DP25 F7 CDT-DC 56 GH DP25 F7 CDT-DC 56 H P DP25 F7 CDT-DC 56 DH P DP25 F7 CDT-DC 56 EH P DP25 F7 CDT-DC 56 GH P DP25 F7 UPRIGHT Range 05 CD-DC 05 CV DP25 F7 CD-DC 05 DV DP25 F7 CD-DC 05 EV DP25 F7 CD-DC 05 CV P DP25 F7 CD-DC 05 DV P DP25 F7 CD-DC 05 EV P DP25 F7 Range 08 CD-DC 08 CV DP25 F7 CD-DC 08 DV DP25 F7 CD-DC 08 EV DP25 F7 CD-DC 08 CV P DP25 F7 CD-DC 08 DV P DP25 F7 CD-DC 08 EV P DP25 F7 Range 18 CD-DC 18 CV DP25 F7 CD-DC 18 DV DP25 F7 CD-DC 18 EV DP25 F7 CD-DC 18 CV P DP25 F7 CD-DC 18 DV P DP25 F7 CD-DC 18 EV P DP25 F7 Range 30 CD-DC 30 CV DP25 F7 CD-DC 30 DV DP25 F7 CD-DC 30 EV DP25 F7 CD-DC 30 CV P DP25 F7 CD-DC 30 DV P DP25 F7 CD-DC 30 EV P DP25 F7 Range 45 CDT-DC 45 CV DP25 F7 CDT-DC 45 DV DP25 F7 CDT-DC 45 EV DP25 F7 CDT-DC 45 CV P DP25 F7 CDT-DC 45 DV P DP25 F7 CDT-DC 45 EV P DP25 F7 Range 56 CDT-DC 56 CV DP25 F7 CDT-DC 56 DV DP25 F7 CDT-DC 56 EV DP25 F7 CDT-DC 56 CV P DP25 F7 CDT-DC 56 DV P DP25 F7 CDT-DC 56 EV P DP25 F7

12 /DI/DC DP25 F7 standard configurations ase on these standard configurations other configurations can be quickly and simply adapted by the installer. NEW IRE IRNUEVO EXTRCTED IRE EXTRIDO IR HORIZONTL UPRIGHT CD-D 05/08/18/30 CH CDT-D 45/56 CH CD-D 05/08/18/30 V CDT-D 45/56 V CD-D 05/08/18/30 V CDT-D 45/56 V CD-D 05/08/18/30 HV CDT-D 45/56 HV Conf. CH Conf. V Conf. V Conf. HV I HORIZONTL CD-DI 05/08/18 H MONO CD-DI 30 H TRI CDT-DI 45/56 H TRI CD-DI 05/08/18 DH MONO CD-DI 30 DH TRI CDT-DI 45/56 DH TRI CD-DI 05/08/18 EH MONO CD-DI 30 EH TRI CDT-DI 45/56 EH TRI CD-DI 05/08/18 GH MONO CD-DI 30 GH TRI CDT-DI 45/56 GH TRI Co n f. H Co n f. DH Co n f. EH Co n f. GH UPRIGHT CD-DI 05/08/18 CV MONO CD-DI 30 CV TRI CDT-DI 45/56 CV TRI CD-DI 05/08/18 DV MONO CD-DI 30 DV TRI CDT-DI 45/56 DV TRI CD-DI 05/08/18 EV MONO CD-DI 30 EV TRI CDT-DI 45/56 EV TRI Co n f. CV Co n f. DV Co n f. EV

13 /DI/DC DP25 F7 standard configurations NEW IRE IRNUEVO C EXTRCTED IRE EXTRIDO IR HORIZONTL CD-DC 05/08/18/30 H CDT-DC 45/56 H CD-DC 05/08/18/30 DH CDT-DC 45/56 DH CD-DC 05/08/18/30 EH CDT-DC 45/56 EH CD-DC 05/08/18/30 GH CDT-DC 45/56 GH Conf. H Conf. DH Conf. EH Conf. GH UPRIGHT CD-DC 05/08/18/30 CV CDT-DC 45/56 CV CD-DC 05/08/18/30 DV CDT-DC 45/56 DV CD-DC 05/08/18/30 EV CDT-DC 45/56 EV Conf. CV Conf. DV Conf. EV

14 DP25 F7. Dimensions (mm) Electrical panel dimensions for all versions CD-D/DC/DI Regulation with an electronic microprocessor (SIC, PROGRM, DVNZ or DOMO). * The electrical panel is installed in the side panel fan drive. Horizontal configuration (H) C Ø D E a b h Weight (Kg) CD-D , CD-D CD-D CD-D , CDT-D , CDT-D , b b a a C C ø ø h h D D ø1/2" ø1/2" E E * The electrical panel is installed in the side panel fan drive. Horizontal configuration (H) con by-pass (P) C Ø D E a b h Weight (Kg) CD-D , CD-D CD-D CD-D , CDT-D , CDT-D ,

15 DP25 F7. Dimensions (mm) Electrical panel dimensions for all versions CD-D/DC/DI Regulation with an electronic microprocessor (SIC, PROGRM, DVNZ or DOMO). C C b b D D a a E E h h ø ø F F ø1/2" ø1/2" * The electrical panel is installed in the side panel fan drive, can be positioned up, down, right or left (depending on configuration of the heat recovery). Upright configuration (V) C Ø D E F a b h Weight (Kg) CD-D , CD-D CD-D CD-D CDT-D , CDT-D , C C b b D D a a E E h h ø ø F F ø1/2" ø1/2" * The electrical panel is installed in the side panel fan drive, can be positioned up, down, right or left (depending on configuration of the heat recovery). Upright configuration (V) con by-pass (P) C Ø D E F a b h Weight (Kg) CD-D , CD-D CD-D CD-D CDT-D , CDT-D ,

16 I-DC DP25 F7. Dimensions (mm) Electrical panel dimensions for all versions CD-D/DC/DI Regulation with an electronic microprocessor (SIC, PROGRM, DVNZ or DOMO). b a ør ø C h D E ø1/2" * The electrical panel is installed in the side panel fan drive. Horizontal configuration (H) C Ø D E ØR a b h Weight (Kg) CD-DI-DC , /2" CD-DI-DC /2" CD-DI-DC /2" CD-DI-DC ,5 1" CDT-DI-DC , " CDT-DI-DC , " b a ø C ør h D ø1/2" E * The electrical panel is installed in the side panel fan drive. Horizontal configuration (H) con by-pass (P) C Ø D E ØR a b h Weight (Kg) CD-DI-DC , /2" CD-DI-DC /2" CD-DI-DC /2" CD-DI-DC ,5 1" CDT-DI-DC , " CDT-DI-DC , "

17 I-DC DP25 F7. Dimensions (mm) Electrical panel dimensions for all versions CD-D/DC/DI Regulation with an electronic microprocessor (SIC, PROGRM, DVNZ or DOMO). C b D a E h ør ø F 100 ø1/2" * The electrical panel is installed in the side panel fan drive, can be positioned up, down, right or left (depending on configuration of the heat recovery). Upright configuration (V) C Ø D E F ØR a b h Weight (Kg) CD-DI-DC , /2" CD-DI-DC /2" CD-DI-DC /2" CD-DI-DC " CDT-DI-DC , " CDT-DI-DC , " C b D a E h ør ø 100 F ø1/2" * The electrical panel is installed in the side panel fan drive, can be positioned up, down, right or left (depending on configuration of the heat recovery). Upright configuration (V) con by-pass (P) C Ø D E F ØR a b h Weight (Kg) CD-DI-DC , /2" CD-DI-DC /2" CD-DI-DC /2" CD-DI-DC , " CDT-DI-DC , " CDT-DI-DC , "

18 Performance curves Qv = Volume in m 3 /h. Ps = Static pressure in mmwg and Pa Pabs = Power absorbed at the maximum velocity (W). Normal dry air at 20 C and 760 mmhg Performance data in accordance with ISO 5801 and MC Standards. dditional pressure drop Resistances: ll 10 Pa models. atteries: 05 Range 16Pa, 08 Range 13Pa, 18 Range 31Pa, 30 Range 27Pa, 45 Range 60Pa, 56 Range 100Pa. Pe Ps Pa mmwg mmca V3 V4 V2 V1 CD-D/DI/DC 05 Pabs ( W ) Qv (m 3 /h) Eff. Rend (%)( % ) V1 Ps Pe Pa mmwg mmca V4 V1 V2 V3 CD-D/DI/DC 08 Pabs ( W ) Qv (m 3 /h) Eff. Rend (%)( % ) V Ps mmwg CD-D/DI/DC 18 Ps CD-D/DI/DC 30 mmwg Eff. (%) Eff. (%) Ps mmwg CDT-D/DI/DC 45 Ps Pe Pa mmwg mmca CD-D/DI/DC 56 Pabs ( W ) Eff. (%) Qv (m 3 /h) Eff. Rend (%)( % )

19 coustical characteristics Lw, levels of noise transmitted in the inlet conduit and radiated in accordance with regulation EN ISO Noise transmitted CD-D d() L W V 1 21,5 17, L W V 2 28,5 23, L W V 3 33,5 29, L W V 4 38,5 35, Noise radiated CD-D d() L W V 1 15,5 13, L W V 2 21,5 18, L W V 3 26,5 23, L W V 4 30,5 28, Noise transmitted CD-D d() L W V 1 30,5 25, L W V 2 36,5 33, L W V 3 40,5 38, L W V 4 43,5 41, Noise radiated CD-D d() L W V 1 23,5 20, L W V 2 28,5 27, L W V 3 32,5 31, L W V 4 34,5 33, Noise transmitted CD-D d() L W V 1 49,5 48, L W V 2 52,5 51, L W V 3 51,5 53, Noise radiated CD-D d() L W V 1 39,5 39, L W V 2 42,5 42, L W V 3 41,5 44, Noise transmitted CD-D d() L W V 1 40,5 41, L W V 2 53,5 50, L W V 3 55,5 62, Noise radiated CD-D d() L W V 1 32,5 33, L W V 2 42,5 41, L W V 3 44,5 51, Noise transmitted CDT-D d() L W V max 66,5 67, Noise radiated CDT-D d() L W V max 62,5 61, Noise transmitted CDT-D d() L W V max 68,5 69, Noise radiated CDT-D d() L W V max 64,5 62, Mounting accessories FR Spare filter Spare filter Spare filter G4 Spare filter F7 Spare filter F9 CD-D/DI/DC 05 FR-D/DI/DC 05 G4 FR-D/DI/DC 05 F7 FR-D/DI/DC 05 F9 CD-D/DI/DC 08 FR-D/DI/DC 08 G4 FR-D/DI/DC 08 F7 FR-D/DI/DC 08 F9 CD-D/DI/DC 18 FR-D/DI/DC 18 G4 FR-D/DI/DC 18 F7 FR-D/DI/DC 18 F9 CD-D/DI/DC 30 FR-D/DI/DC 30 G4 FR-D/DI/DC 30 F7 FR-D/DI/DC 30 F9 CDT-D/DI/DC 45 FR-D/DI/DC 45/56 G4 FR-D/DI/DC 45/56 F7 FR-D/DI/DC 45/56 F9 CDT-D/DI/DC 56 FR-D/DI/DC 45/56 G4 FR-D/DI/DC 45/56 F7 FR-D/DI/DC 45/56 F9

20 Mounting accessories CFIL* Filtering box PC Inlet/discharge protection guards CD-D/DI/DC 05 CD-D/DI/DC 08 CD-D/DI/DC 18 CD-D/DI/DC 30 CD-D/DI/DC 45 CD-D/DI/DC 56 Filtering box CFIL-200 CFIL-250 CFIL-315 CFIL-355 CFIL-450 CFIL-450 CD-D/DI/DC 05 CD-D/DI/DC 08 CD-D/DI/DC 18 CD-D/DI/DC 30 CD-D/DI/DC 45 CD-D/DI/DC 56 Inlet/discharge protection guards PC-200 PC-250 PC-315 PC-355 PC-450 PC-450 MSO Flexible coupling CD-D/DI/DC 05 CD-D/DI/DC 08 CD-D/DI/DC 18 CD-D/DI/DC 30 CD-D/DI/DC 45 CD-D/DI/DC 56 Flexible coupling MSO-200 MSO-250 MSO-315 MSO-355 MSO-450 MSO-450 SIL Sound attenuators to mount at the inlet and/or discharge of the heat recovery units CD-D/DI/DC 05 CD-D/DI/DC 08 CD-D/DI/DC 18 CD-D/DI/DC 30 CD-D/DI/DC 45 CD-D/DI/DC 56 Sound attenuator SIL-200 SIL-250 SIL-315 SIL-355 SIL-450 SIL-450 SIFÓN RECUPERDORES* Drain water drainage of the heat recovery TPP External rain protection canopy TPP D-H Rain Cap CD-D 05 H TPP D-H 05 CD-D 08 H TPP D-H 08 CD-D 18 H TPP D-H 18 CD-D 30 H TPP D-H 30 CDT-D 45 H TPP D-H 45/56 CDT-D 56 H TPP D-H 45/56 TPP D-V Rain Cap CD-D 05 V TPP D-V 05 CD-D 08 V TPP D-V 08 CD-D 18 V TPP D-V 18 CD-D 30 V TPP D-V 30 CDT-D 45 V TPP D-V 45/56 CDT-D 56 V TPP D-V 45/56 TPP DI/DC-H Rain Cap CD-DI/DC 05 H TPP DI/DC-H 05 CD-DI/DC 08 H TPP DI/DC-H 08 CD-DI/DC 18 H TPP DI/DC-H 18 CD-DI/DC 30 H TPP DI/DC-H 30 CDT-DI/DC 45 H TPP DI/DC-H 45/56 CDT-DI/DC 56 H TPP DI/DC-H 45/56 TPP DI/DC-V Rain Cap CD-DI/DC 05 V TPP DI/DC-V 05 CD-DI/DC 08 V TPP DI/DC-V 08 CD-DI/DC 18 V TPP DI/DC-V 18 CD-DI/DC 30 V TPP DI/DC-V 30 CDT-DI/DC 45 V TPP DI/DC-V 45/56 CDT-DI/DC 56 V TPP DI/DC-V 45/56 TTP D/DI/DC P To heat recovery horizontal with by-pass CD-D 05 H P CD-D 08 H P CD-D 18 H P CD-D 30 H P CD-DI/DC 05 H P CD-DI/DC 08 H P CD-DI/DC 18 H P CD-DI/DC 30 H P Rain Cap TPP D-H 05 P TPP D-H 08 P TPP D-H 18 P TPP-D-H 30 P TPP-DI/DC-H 05 P TPP-DI/DC-H 08 P TPP-DI/DC-H 18 P TPP-DI/DC-H 30 P See complete information on the HET RECOVERY CCESSORIES.

21 Mounting accessories Versions CD-D 05 H to 30 H with by-pass 5º 5º Versions CD-D 05 H to 30 H without by-pass Versions CDT-D 45 H and 56 H with and without by-pass 5º Versions V with and without by-pass External rain protection canopy incorporates 4 side panels CD-D 05 H CD-D 08 H CD-D 18 H CD-D 30 H CDT-D 45 H CDT-D 56 H CD-D 05 V CD-D 08 V CD-D 18 V CD-D 30 V CDT-D 45 V CDT-D 56 V Versions CD-DI/DC 05 H to 30 H with by-pass 5º 5º Versions CD-DI/DC 05 H to 30 H without by-pass Versions CDT-DI/DC 45 H and 56 H with and without by-pass External rain protection canopy incorporates 4 side panels 5º Versions I/DC V with and without by-pass CD-DI/DC 05 H CD-DI/DC 08 H CD-DI/DC 18 H CD-DI/DC 30 H CDT-DI/DC 45 H CDT-DI/DC 56 H CD-DI/DC 05 V CD-DI/DC 08 V CD-DI/DC 18 V CD-DI/DC 30 V CDT-DI/DC 45 V CDT-DI/DC 56 V

22 Electrical accessories ccessories for the Variable ir Volume System by CO2 Variable frequency drive Sensor CD-D/DI/DC 05 RQ3 SCO2- / SCO2-D / SCO2-G CD-D/DI/DC 08 RQ3 SCO2- / SCO2-D / SCO2-G CD-D/DI/DC 18 VPZ-11 SCO2- / SCO2-D / SCO2-G CD-D/DI/DC 30 VPZ-11 SCO2- / SCO2-D / SCO2-G CD-D/DI/DC 45 VFTM TRI 2,2 SCO2- / SCO2-D / SCO2-G CD-D/DI/DC 56 VFTM TRI 4 SCO2- / SCO2-D / SCO2-G ccessories for Constant Pressure operation Variable frequency drive Sensor CD-D/DI/DC 05 Pack PR Pa Included CD-D/DI/DC 08 Pack PR Pa Included CD-D/DI/DC 18 Pack PR Pa Included CD-D/DI/DC 30 Pack PR Pa Included CD-D/DI/DC 45 VFTM TRI 2,2 TDP-S / TDP-D CD-D/DI/DC 56 VFTM TRI 4 TDP-S / TDP-D RQ3 utomatic speed adjustment according to CO 2 concentration. Works together with a CO 2 probe (SCO2-1/10V ambient and, SCO2-D or in the SCO2-G conduit). Only for 05 and 08 models. VFTM TRI Variable frequency drive enabling the fan speed to be modified according to CO 2 concentration. Works together with a CO 2 probe (SCO2- ambient and SCO2-D or in the SCO2-G conduit). Only for 45 and 56 models. Pack PR Voltage regulator for single-phase motors with pressure probe included for control of constant pressure systems. VPZ-11 Controller, enabling the fan speed to be modified according to CO 2 concentration. Maximum current 11. Works together with a CO 2 probe (SCO2- ambient and, SCO2- and SCO2-D or in the SCO2-G conduit). Only for 18 and 30 models. Electrical supply Maximum current () Voltage (V) IP Operating temp. range Dimensions LxxH (mm) Pack PR 5 230V-50/60Hz IP55-10 to x200x80 Pack PR V-50/60Hz IP55-10 to x200x80 Electrical supply Maximum current () Voltage (V) IP Operating temperature range Dimensions LxxH (mm) VPZ V-50Hz IP55-10 to x115x92 Electrical supply Maximum power (V) TDP-S / TDP-D Pressure sensor. Enables you to control the pressure in the fan inlet. TDP-S Standard pressure sensor. TDP-D Pressure sensor, with display. Ø Connectors (mm) TDP-S 0-10 V / 24VC-24VDC 4 6,2 TDP-D 4-20 m Voltage IP Pressure range (Pa) Dimensions LxxH (mm) IP x36x80 SCO2-G 0/10 V CO2 sensor probe for duct mounting. Enable control of the ventilation in ductwork according to the CO 2 concentration of the air circulating through it. Electrical supply SCO2-0/10 V 24VDC- 24VC SCO2-D Power (W) 5 SCO2-0/10 V mbient CO 2 and temperature sensor. Enables control of the ventilation in sections of conduit according to the temperature and relative humidity of the air circulating through it or to the temperature. SCO2-D mbient CO 2 and temperature sensor with display. Enable control of the ventilation ductwork according to the temperature and relative humidity of the air circulating through it or to the temperature. Voltage Height instal. (m) IP CO 2 range (pm) For controlled equipment only a 0-10 V probe can be connected. Temperature range (ºC) Dimensions LxxH (mm) 0-10V 1,5-3,5 IP x26x m SCO2-G 0/10 V Electrical supply Power (W) Voltage (V) IP CO 2 range (pm) Dimensions LxxH (mm) 24VDC-24VC ox IP x238x80

23 Electrical accessories COM3 / COM4 3 and 4 speed switch SQ utomatically switches the fan on when the quality of the ambient air deteriorates below an acceptable level due to fumes, odours, tobacco, smoke or dampness etc djustable run-on-timer facility which enables the fan to operate for a pre-selected time period after the air quality sensor has switched off. Important: this sensor must not be used to detect combustible gases or fires ans in connection with any safety alarm systems. Switch Maximum current () CD-D/DI/DC 05 COM4 12 CD-D/DI/DC 08 COM4 12 CD-D/DI/DC 18 COM3 20 CD-D/DI/DC 30 COM3 20 IP protection Class Maximum current () Operating temperature (ºC) Timer adjustment IP21 II ( ) 2* min. * For inductive loads. PULSER Electronic controller to regulate the heat output for single phase electric heater battery up to 16, in order to maintain a constant pre-selected temperature. Depending on the selected temperature, the controller pulses the entire power output anduses a time-proportional control to maintain that temperature. The PULSER incorporates a built-in room temperature sensor with an input for external sensor. IP-30. Maximum heaterpower 3,6kW. TTC-25 Electronic controller to regulate the heat output for three phase electric heater battery up to 25, in order to maintain a constant pre-selected temperature. Depending on the selected temperature, the controller pulses the entire power output and uses a time-proportional control to maintain that temperature. The TTC-25 is designed to be fitted in a cabinet on DIN-rail. IP-20. PULSER-DD Supplementary unit for slave control from another PULSER to control batteries with power ratings superior to the PULSER capacity (3600W V). PULSER M Electronic controller similar to the PULSER, incorporating in addition, input for an external duct sensor to control minimum or maximum temperature limitations. IP-30. Maximum heaterpower 3,6kW. PULSER D Electronic controller to regulate the heat output for single phase electric heater battery up to 16, in order to maintain a constant pre-selected temperature. Depending on the selected temperature, the controller pulses the entire power output and uses a time-proportional control to maintain that temperature. The PULSER D is designed to be fitted in a cabinet on DIN-rail. IP-20. Maximum heater power 3,6kW.). TG-R430 Room sensor with set point adjustment between 0 and +30ºC. TI-10 Potentiometer mounted on the main board panel for setting temperature between -20 and +10ºC. Used with the PULSER-D or TTC-25 mounted within cabinet, to set the minimum air temperature before entering in the heat exchanger.

24 Electrical accessories TI-30 Potentiometer mounted on the main board panel for setting temperature between 0 and +30ºC. Used with the Pulser-D and with a TTC-25 duct sensor to set the air temperature after the electric battery in post heating operation. MCR-1 Timer with set point between 1 sec and 100 h. Used in an electric heating system to delay the fan switch off after disconnecting the system. PRESSURE SWITCH DPS 2-30 Differential pressure switch to control the fan running and the filter clogging up. Working pressure range from 2 to 30 mmwg. TG-K310, TG-K330 and TG-K360 Duct temperature sensor. Temperature range: TG-K310 from -20 to 10ºC TG-K330 from 0 to 30ºC TG-K360 from 0 to 60ºC 3WV C* Motorized 3-way valves. TRNSFORMER C Transformer 200V / 24V C for vales supply. Valve DN (mm) DN (") Kvs (m 3 /h) CD-D/DI/DC 05 3 WV CD-DC 05/ /2 2,5 CD-D/DI/DC 08 3 WV CD-DC 08/ /2 1,6 CD-D/DI/DC 18 3 WV CD-DC 08/ /2 1,6 CD-D/DI/DC 30 3 WV CD-DC 05/ /2 2,5 CDT-D/DI/DC 45 3 WV CDT-DC 45/ /4 6,3 CDT-D/DI/DC 56 3 WV CDT-DC 45/ /4 6,3 * See complete information on the HET RECOVERY CCESSORIES.

25 mbient temperature and inlet air temperature control Heat recovery DP25 F7 Electric heating batteries with built-in temperature control to fit on versions : consists of electric resistances, conduit probe, electric battery regulator and internal potentiometer. Heat recovery Ø (mm) Power (W) Voltage Nº stages Minimum airflow (m 3 /h) E-SCT 200M CD-D V-1-50Hz E-SCT 250M CD-D V-1-50Hz E-SCT 315M CD-D V-1-50Hz E-SCT 355T CD-D V-3-50Hz E-SCT 450T CDT-D V-3-50Hz E-SCT 500T CDT-D V-3-50Hz Heat recovery I DP25 F7 Control elements needed for managing the operation of the built-in resistances in the heat exchangers. uilt-in electric heater Supply Power (kw) Nº of stage ir ambient temperature control * The DD Pulser should be installed with the M Pulser when the power exceeds 3.6 kw. Supply air temperature control Controller in room Controller Controller within cabinet (Din-rail) djust. Duct sensor to limit Electric controller with Min/Max limiting sensor room sensor 0/30ºC Electric controller Duct sensor 0/30ºC supply air temperature 0/60ºC Optional External potentiometer on cabinet 0/30ºC CD-DI 05 Single phase 230V 2 1 PULSER PULSER M TG-R430 PULSER D TG-K330 TG-K360 TI-30 MCR-1 CD-DI 08 Single phase 230V 4 2 PULSER + P.DD* PULSER + P.DD* TG-R430 PULSER D + P.DD* TG-K330 TG-K360 TI-30 MCR-1 CD-DI 18 Single phase 230V 6 2 PULSER + P.DD* PULSER + P.DD* TG-R430 PULSER D + P.DD* TG-K330 TG-K360 TI-30 MCR-1 CD-DI 30 Three phase 400V TG-R430 TTC-25 TG-K330 TG-K360 TI-30 MCR-1 CDT-DI 45 Three phase 400V TG-R430 TTC-25 TG-K330 TG-K360 TI-30 MCR-1 CDT-DI 56 Three phase 400V TG-R430 TTC-25 TG-K330 TG-K360 TI-30 MCR-1 Timer Installation with external electric heater Supply Ø (mm) Power (kw) Electric heater type Electric heater Defrosting operation control (Heat exchanger protection) Duct sensor -20/10ºC External potentiometer -20/30ºC Electric heater Supply air temperature control Duct sensor 0/30ºC External potentiometer 0/30ºC CD-D 05 Single phase 230V 200 2,1 E-200/2M PULSER D TG-K310 TI-10 PULSER D TG-K330 TI-30 CD-D 08 Single phase 230V E-250/3M PULSER D TG-K310 TI-10 PULSER D TG-K330 TI-30 CD-D 18 Single phase 230V E-315/4M PULSER D + P.DD TG-K310 TI-10 PULSER D + P.DD TG-K330 TI-30 CD-D 30 Three phase 400V E-355/60T TTC-25 TG-K310 TI-10 TTC 25 TG-K330 TI-30 CDT-D 45 Three phase 400V E-400/90T TTC-25 TG-K310 TI-10 TTC 25 TG-K330 TI-30 CDT-D 56 Three phase 400V E-400/90T TTC-25 TG-K310 TI-10 TTC 25 TG-K330 TI-30

26 Electric heater batteries The heater battery operation must be enslaving to the fan operation. The installation must include a pressure switch to switch off the electric heater battery supplies in case of fan failure. E-SCT* Electric heating batteries with built-in electronic temperature control. E* Electric heater batteries Functions: - Defrosting operation. - Post heating operation. CD-D/DI/DC 05 CD-D/DI/DC 08 CD-D/DI/DC 18 CD-D/DI/DC 30 CDT-D/DI/DC 45 CDT-D/DI/DC 56 Electric heater batteries E-200/2M E-250/3M E-315/4M E-355/60T E-400/90T E-400/90T ccessories for air treatment -C* External coil module for hot water. External coil module CD-D/DI/DC 05 -C 05 CD-D/DI/DC 08 -C 08 CD-D/DI/DC 18 -C 18 CD-D/DI/DC 30 -C 30 CDT-D/DI/DC 45 -C 45 CDT-D/DI/DC 56 -C 56 -F* External coil module for cold water. External coil module CD-D/DI/DC 05 -F 05 CD-D/DI/DC 08 -F 08 CD-D/DI/DC 18 -F 18 CD-D/DI/DC 30 -F 30 CDT-D/DI/DC 45 -F 45 CDT-D/DI/DC 56 -F 56 HUMC* diabatic cooling module. CD-D/DI/DC 05 CD-D/DI/DC 08 CD-D/DI/DC 18 CD-D/DI/DC 30 CDT-D/DI/DC 45 CDT-D/DI/DC 56 * See complete information on the HET RECOVERY CCESSORIES. diabatic cooling module HUMC-05 HUMC-08 HUMC-18 HUMC-30 HUMC-45 HUMC-56