Specification data Topvex. Rotating or Cross flow heat exchanger.

Transcription

1 Specification data Topvex Rotating or ross flow heat exchanger

2 Topvex Topvex SR, TR, SX and TX is a series of efficient ventilation units designed for offices, shops, schools, daycare centres or similar premises. The units are especially designed to meet the coming energy requirements and have therefore a very low energy use. To simplify the installation and commissioning the units are included with control system and pre-configured. fan motors low energy use and low noise Unlike motors with frequency converters, the motors operate with high efficiency even at low RPM (see the diagram). This contributes to good energy saving performance. The motors are also very quiet at both high and low RPM. rives High efficiency even at reduced speed asy inspection To facilitate inspection and maintenance, both fans and the rotating/crossflow heat exchanger are removable. SR07, 09 and 11 have a fi xed heat excanger. ll power cables have quick release couplings the fans and heat exchanger can be released easily. It could not be easier! Topvex are delivered pre-programmed, tested and ready for installation. onnect the Topvex unit to the duct system, connect any external components, connect the main supply, set the time and date, adjust the week scheduler, temperatures, airflows and the unit is installed. It could not be easier! fficiency (%) Speed (min -1 ) 2

3 asy electrical connections and service ll electrical connections are done at the same terminal block, with clear markings. General Topvex units are delivered enclosed in plastic and mounted on pallets. The units are fully connected internally. The automatic control system is preset and has been test-run at the factory. ny cables to external components should be connected to terminals in the connection space. The same applies to valve actuators for heating coils. Measurement at Systemair's evelopment entre Topvex are measured and tested at Systemair's evelopment entre. The air volume is measured in accordance with M Laboratory methods of testing fans for rating. Sound is measured in accordance with M Test ode for Sound Rating. Topvex TX06 L Unit housing The unit's casing is made up from double-skinned 1.0 mm aluzinc sheet metal, Z 185, with 50 mm of internal insulation. To avoid sharp edges bevelled corners from cast aluminium are used. Topvex stands on fi xed sections that raise the units about mm above the floor. Topvex has large front doors that have lockable handles and removable hinges. separate safety switch is included. The control panel is connected with 10 m cable (included). Topvex TR09-15 L Topvex SR04-06 L 3

4 e-icing function TX/SX Ice accretion of the heat exchanger is depending on the outdoor temperature and the humidity in the extract air. The humidity in the extract air is varying a lot depending on the activities in the building e.g. an industry premises is normally producing much less humidity than a day-care centre. Therefore has the aggressiveness of the de-icing function been made settable (1-5) so that it can be optimized to different applications. Topvex SX06 L omponents ans Topvex has effective plug-fans with maintenance-free external rotormotors. The fans have been selected to provide optimal operation in respect of air volume, sound level and efficiency. The units have electronically commutated motors, so called -motors with very high efficiency. The motors are controlled in steps via the control unit. To facilitate maintenance and servicing the fans have quick release connections for the electrical cables. Heat exchanger Rotating The rotating heat exchanger is nonhygroscopic and belt driven. spare belt is mounted on the rotor wheel on delivery. The rotor belt is a round plastic belt of the elastic type with high friction. rotor guard will give an alarm if the rotating heat exchanger stops. The rotor construction with pleated aluminium is optimised in respect of high efficiency and low pressure drop. The rotor have a robust construction witch makes it stable and reliable also after a very long time of operating. t balanced airflows the efficiency is up to 85%. The heat exchanger is removable with quick release connections for the power cables. Heat exchanger rossflow The crossflow heat exchanger is non-hygroscopic. The construction with pleated aluminium is optimised in respect of high efficiency and low pressure drop. t balanced airflow the efficiency is up to 60%. The heat exchanger is removable with quick release connections for the power cables. y-pass damper Topvex TX/SX is equipped with a stepless by-pass damper as standard. The damper is used to by-pass the supply air during warm season(no need of heat recovering) and to de-ice the heat exchanger during cold season (selectable). Heating coil water The hot water coil is located after the supply air fan. The coil is mounted for easy connection of the water pipes through out the gable of the unit. The material is copper piping with a frame of galvanised sheet steel and aluminium fins. The coil has venting nipples and an immersion sensor as frost guard. If there is a risk of freezing in the hot water coil, the control valve is forced open to prevent freezing. If there is still a risk of freezing, the unit is stopped and the outdoor air damper (accessory) is closed. fter a freezing situation, the unit will re-start when the return water temperature is above 7 and the alarm has been acknowledged. The hot water coils are available in: Low power HWL (all Topvex) High power HWH (Topvex TR/TX/ SR/SX 03-06). Heating coil electric The heating coil is located after the supply air fan. It has elements of stainless steel. The electric heating coil has two overheating protection one with automatic reset and one with manual reset. When the unit is switched off, through the overheating protections, the built-in clock or the hand/auto switch, the electrical heater is immediately stopped while the fans are kept running during 3 minutes for cooling down the heater. fter an overheating situation, the unit will re-start when the overheating protection has been reset and the alarm has been acknowledged. 4

5 ilters The units are delivered with bag fi lters as standard. oth of the fi lters are placed before the heat exchanger, to keep the exchanger clean. The fi lters are mounted in guide rails that facilitate insertion and removal for inspection and service. The guide rails are spring mounted and fitted with sealing strips to provide optimal sealing against the fi lters. ilter class 7 on supply air and 5 on extract air are used as standard. ilter monitoring is done via the built-in timer (Standard controller) or via built in pressure transmitters measuring the fi lter pressure drop (dvanced controller). 5 7 uct connection ircular connections with rubber sealing, rectangular have flanged connections. Topvex Rectangular ircular TR03 ø250 TR04 ø315 TR06 250x500 TR09 300x700 TR12 350x800 TR15 350x1000 SR03 ø315 SR04 500x250 SR06 600x300 SR07 600x300 SR09 600x400 SR11 800x400 TX03 ø250 TX04 ø315 TX06 300x500 SX03 ø315 SX04 500x250 SX06 600x300 Optional heat exchangers/connections TR 03, 04, 06, 09, 12, 15 SR 03, 04, 06, 07, 09, 11 TX 03, 04, 06 SX 03, 04, 06 5

6 Overview onnections & heat exchangers lue margin = Top connection Green margin = Side connection = Rotating heat exchanger = ross flow heat exchanger imensions Top connection Width Height epth ivisible TR TR TR TR /2= 895 TR /2= 965 TR /2= 965 TX TX TX Side onnection Width Height epth ivisible SR SR SR SR /2-29= 890 SR /2-29= 890 SR /2-29= 890 SX SX SX Min/max airflow TX 03 TR 03 TX 04 TX 06 TR 04 TR 06 TR 09 TR 12 TR 15 0,0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 2,0 m 3 /s m 3 /h SX 03 SR 03 SX 04 SX 06 SR 04 SR 06 SR 07 SR 09 SR 11 0,0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 2,0 m 3 /s m 3 /h 6

7 isplay The illuminated display has 4 rows of 20 characters each and 20 different languages are available. rrows are used to simplify the usage. The background illumination is normally switched off, and is activated by pushing one of the buttons. The illumination is then switched off again after a period of inactivity. Ls The alarm L is marked with a symbol. The write enable L is marked with a symbol. Push-uttons ll functions can be set (configured) by using the information in the display and the push-buttons on the controller. Standard & dvanced control Systemair are using two different controls depending on ir Handling Unit. To facilitate the use of the controllers both controllers have the same menu structure and using the same technical terms. or further information, see page Standard, 17S TR03-06 TX03-06 SR03-06 SX03-06 dvanced, 28 TR09-15 SR07-11 ontrols Standard is a controller designed to be easy to handle. This controller is used in the smaller ompact HU's, up to approx m 3 /h. dvanced is a fully equipped controller designed to cover the most of the market needs. dvanced is used in the larger ompact HU's, m 3 /h. SP control panel Width = 115 mm Height = 94 mm epth = 26 mm Main difference between Standard and dvanced control: Standard, 17S dvanced, 28 Using of -tool, a P-based No Yes commissioning software. Temperature control 3 control modes 6 control modes Time controlled airflow Week timer Week timer + Holidays + igital timer channels for e.g. door locks an control Settable between 0-100% control signal. V, constant air volume or VV, variable air volume. Outdoor temp. dependent airflow. Heat exchanger control Rotating, on/off. Rotating, step-less. emand control X cooling control, (xternal X cooler) Possible to use external equipment with relay output for increasing airflow one step. Step controller for converting the analogue controls signal to a digital 2-step, binary control necessary (accessory). Possible to use external equipment with analogue output for step-less increasing of air flow or relay output. Up to 3-step, binary control is standard. HW/W Pump control No Yes ilter supervising Time controlled Pressure drop controlled 7

8 Regulations S=standard settings P=possible settings =choose when ordering O=option SR03, 04, 06 SX03, 04, 06 SR07, 09, 11 TR03, 04, 06 TX03, 04, 06 TR09, 12, 15 ontroller Standard, 17S Standard, 17S dvanced, 28 ontrol Panel Remote with 10 meter cable S S S Repeater When more than 10 meter between unit and control panel O O O ommissioning software tool O Temperature control xtract air P P S air S S P Outdoor temperature compensated air P P P ascaded Room control P Outdoor temp. dependent switching between /xtract air or /Room control P ir flow control Week timer, two separate running periods S S S an control Individual stepless voltage control S S ir flow control, V Pressure control, VV Outdoor compensated air flow S Heat exchanger ross flow S y pass damper, stepless S Rotating, on/off S Rotating, stepless S Heater Hotwater lectrical ooler old water coil V output signal P P P X cooling. 24V (1, 2 or 3-stage binary) output. * P * P P ree cooling Wall mounted outdoor sensor and room temp. sensor necessary P ool recovering P P P emand ventilation, O 2 2-step, O 2 sensor with a potential free switch. P P Stepless, O 2 sensor with V output signal. P Pump control Heating, 24V output signal P ooling, 24V output signal P xchanger efficiancy uct mounted exhaust temp. sensor necessary. P xtended running S S S Week schedule hanging between Normal run, Reduced run or Off. S S S amper control Outdoor/xhaust air S S S larm larm messages S S S High and low priority S Sum alarm, 24V output signal S S S ilter alarm on time (month) S S ilter alarm on pressure difference (Pa) S ommunication xoline, Modbus via RS 485 S S S LON, xoline via TP/IP O O * Step controller S2/ is necessary. onverts V signal to relay output. 8

9 Notes 9

10 Topvex TR Topvex TX TX06 TR09-15 TX03-04 TR06 TR03-04 T Top connection R Rotating heat exchanger X ross flow heat exchanger Topvex TR/TX is a Plug and play air handling unit with a modern design intended for ventilating offices, day-care centres or used as zone ventilation in larger buildings e.g. schools. Top-connection of the air-ducts minimise the ootprint of the unit. To meet the new restricted energy requirements with low SP (Specific an Power) Topvex is equipped with fan motors. -motors consume an average of 30% less energy than motors. In some applications, the saving can be 50% or more. Topvex TR is equipped with a high efficiency rotating heat exchanger with an efficiency of up to 85%. Rotating heat exchangers do not need condense water drainage and is therefore very flexible to install. Topvex TX with its crossflow heat exchanger is normally used where it is a requirement that the supply and exhaust air must be kept separated. The units have an efficient deicing function. Topvex TR/TX units have energy saving functions like: - Week schedule. - ool recovering to recover the chilliness in the extract air during warm season. If using an external cooling unit. - emand controlled airflow by using a O 2 /humidity sensor, movement detector etc. - Sum alarm output for central supervision of many units. entral supervision secures that incorrect operating, like dirty fi lters, detects early. 10

11 xplanatory sketch TR/TX Topvex TR03-06 Topvex TR09-15 H O OS O H SS WV WV SS TS OS GS PS WV WV PS HS T OT OT T G U U R H TS H PT S S RM RG PTS RM U Unit control S fan xtract an SS air temp. sensor TS xtract air temp. sensor OS Outdoor air temp. sensor OT Overheating thermostat T mergency thermostat PS rost protection temp. sensor WV Water valve actuator (accessories) WV Water valve (accessories) H Heat exchanger RM Rotor motor RG Rotor guard O amper outdoor air (accessories) H amper exhaust air (accessories) U Unit control PS rost protection temp. sensor S fan WV Water valve actuator (accessory) xtract fan WV Water valve (accessory) PTS Pressure transmitter supply air fan H Heat exchanger PT Pressure transmitter extract air fan R Rotor control SS air temp. sensor RM Rotor motor TS xtract air temp. sensor GS ilter pressure guard supply air OS Outdoor air temp. sensor G ilter pressure guard extract air HS xhaust air temp. sensor O amper outdoor air (accessory) OT Overheating thermostat H amper exhaust air (accessory) T mergency thermostat Topvex TX03-06 xtract fan S fan SS air temp. sensor OS Outdoor air temp. sensor TS xtract air temp. sensor LH lectrical re-heater battery T mergency thermostat OT Overheating thermostat WH Water heating battery PS rost protection temp. sensor amper by-pass U Unit control O amper outdoor air (accessory) H amper exhaust air (accessory) WV Water valve actuator (accessory) 11

12 Performance TR03 xtract SP 3,0 SP 2,5 SP 2,0 SP 1,5 10V η 8V V V V V xtract 10V V V V V V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V V V V V V

13 Performance TR04 xtract SP 3,0 SP 2,5 SP 2,0 SP 1,5 10V V η 6V V V xtract 10V V V V V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V V V V V

14 Performance TR06 xtract SP 2,5 SP 2,0 SP 1,5 10V η 7,5V ,5V V V V xtract 10V ,5V ,5V V V V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V ,5V ,5V V V V

15 Performance TR09 xtract SP 3,0 SP 2,5 SP 2,0 SP 1,5 10V η 10V V V V V xtract 10V V V V V V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V V V V V V

16 Performance TR12 xtract SP 2,5 SP 1,5 SP 2,0 10V η 10V V V V V xtract 10V V V ,5V V V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V V V V V V

17 Performance TR15 xtract SP 2,5 SP 1,5 SP 2, = 230V 3-fase units = 230V 3-fase units 10V η 8V V V V V xtract 10V V V V V V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V V V V V V

18 Hot water coil TR n extract air temperature of 21 and a heat exchanger effi ciency of 70% has been used for the calculations below. In practice the heat exchanger effi ciency or extract air temperature may be higher, which may give a few degrees higher supply air temperatures than in the below tables. Topvex TR03 HWL Topvex TR04 HWL Topvex TR06 HWL Water temp. 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 ir flow m 3 /h Outdoor air temp. 0 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp. -10 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp. -20 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp. -30 air temp Water flow l/s Pressure drop kpa , apacity kw Outdoor air temp. -40 air temp Water flow l/s Pressure drop kpa apacity kw Topvex TR03 HWH Topvex TR04 HWH Topvex TR06 HWH Water temp. 60/30 60/30 60/40 60/40 60/30 60/30 60/40 60/40 60/30 60/30 60/40 60/40 irflow m 3 /h Outdoor air temp. 0 air temp ,63 27,69 36,97 32, Water flow l/s 0, Pressure drop kpa apacity kw Outdoor air temp. -10 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp. -20 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp. -30 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp. -40 air temp Water flow l/s Pressure drop kpa apacity kw

19 Hot water coil TR Topvex TR09 HWL Topvex TR12 HWL Topvex TR15 HWL Water temp. 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 irflow m 3 /h Outdoor air temp 0 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp -10 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp -20 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp -30 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp -40 air temp Water flow l/s Pressure drop kpa apacity kw Topvex TR03 Topvex TR04 Topvex TR06 apacity, kw irflow, m 3 /h air temp. air temp. air temp. 0 > > >30 > > >30 > > > >30 22 Outdoor Outdoor Heater battery, electric TR Outdoor Topvex TR09 Topvex TR09 apacity kw irflow m 3 /h air temp. air temp Outdoor Outdoor Topvex TR12 Topvex TR12 Topvex TR15 apacity kw irflow m 3 /h air temp. air temp. air temp Outdoor Outdoor Outdoor 19

20 imensions TR 43 TR G TR TR øl 15R (½") H I J K øl N TR R (½")

21 imensions TR 32,5 72,5 TR M M M M G H I J K K L R ½" 25 G H TR TR TR N 150 O P I J K L M N O P

22 Technical data TR TR03 L TR03 HW TR04 L TR04 HW TR06 L TR06 HW Voltage V requency Hz Phase ~ 3N 1 3N 3N 3N 3N Input power, fan motors W 2 x x x x x x 1005 Input power, electrical heating battery kw use 3x x13 3x10 3x16 3x10 Weight kg ilter, supply air ilter, extract air TR09 L TR09 HW TR12 L TR12 HW TR15 L TR15 HW Voltage V requency Hz Phase ~ 3N 3N 3N 3N 3N 3N Input power, fan motors W 2 x x x x x x 3380 Input power, electrical heating battery kw 6/15 9/21 15 use 3x16/3x35 3x10 3x25/3x50 3x16 3x35 3x16 Weight kg ilter, supply air ilter, extract air ccessories TR03-06 Topvex TR03 Topvex TR04 Topvex TR06 Repeater 1 0-R230K 0-R230K 0-R230K Shut-off damper Valve actuator QM QM QM Valve, 2-way STV15-0,63 STV15-1,0 STV15-1,0 Valve, 3-way STR15-1,0 STR15-1,6 STR15-1,6 ooling battery, water PGK PGK PGK ooling battery, X coil XR XR XR Step controller. X cooling 2 S2/ S2/ S2/ Plastic housing, step controller IP5 U-K U-K U-K Transformer 230/24 V PSS48 PSS48 PSS48 uct sensor TG-KH/PT1000 TG-KH/PT1000 TG-KH/PT1000 ombi grille VVX 250 VVX 315 VVX 400 Silencer L 250 L 315 LR Timer T 120 T 120 T 120 Presence detector IR24-P IR24-P IR24-P O2 Room sensor (digital 1/0) O2RT-R O2RT-R O2RT-R ilter 5 (extract air) T TR03 5 T TR04 5 T TR06 5 ilter 7 (supply air) T TR03 7 T TR04 7 T TR Used when distance between the unit and control panel is more than 10 meters. 2 (24V). onverts V signal to relay output. 22

23 ccessories TR09-15 Topvex TR09 Topvex TR12 Topvex TR15 Repeater 1 0-R230K 0-R230K 0-R230K -Tool cable T T T Shut-off damper Valve actuator QM QM QM Valve, 2-way STV STV STV Valve, 3-way STR15-2,7 STR20-4,2 STR20-5,6 ooling battery, water PGK PGK PGK ooling battery, X coil XR XR XR uct sensor TG-KH/PT1000 TG-KH/PT1000 TG-KH/PT1000 Silencer LR LR LR Timer T 120 T 120 T 120 Room temp sensor TG-R5/PT1000 TG-R5/PT1000 TG-R5/PT1000 Outdoor sensor, wall mount TG-UH7PT1000 TG-UH7PT1000 TG-UH7PT1000 Presence detector IR24-P IR24-P IR24-P O2 Room sensor (digital 1/0) O2RT-R O2RT-R O2RT-R O2 Room sensor (analog V ) O2RT O2RT O2RT U-tube manometer, fi lter guard MRO MRO MRO ilter 5 (extract air) T TR09 5 T TR12 5 T TR15 5 ilter 7 (supply air) T TR09 7 T TR12 7 T TR Used when distance between the unit and control panel is more than 10 meters. 23

24 Ordering code TR TR Model: TR03, TR04, TR06 Heating coil: electric = L, water = HW vailable power: TR03 L: 3kW TR03 HW: HWL - low power, HWH - high power TR04 L: 4kW TR04 HW: HWL - low power, HWH - high power TR06 L: 6.3 kw TR04 HW: HWL - low power, HWH - high power Right or left model (The side were the supply air is located when viewed from access side) TR Model: TR09, TR12, TR15 Heating coil: electric = L, water = HW vailable power: TR09 L: 6kW alt. 15kW TR09 HW: HWL - low power TR12 L: 9kW alt. 21kW TR12 HW: HWL - low power TR15 L: 15kW TR15 HW: HWL - low power Right or left model (The side were the supply air is located when viewed from access side) V or VV airflow controlling (V= onstant ir Volume, VV= Variable ir Volume) ommunication to MS systems LON xoline/uilt-in Web via TP/IP 24

25 Performance TX03 xtract SP 2,5 SP 1,5 SP 2,0 10V η 10V ,6V ,6V ,6V ,6V = With condensation --- = Without condensation xtract 10V V ,6V ,6V ,6V ,6V Surrounding SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With outside temperature -15 º and extract air temperature 25 º. With condensation: 50%Rh. Without condensation: 0%Rh. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. 10V V ,6V ,6V ,6V ,6V

26 Performance TX04 xtract SP 2,5 SP 1,5 SP 2,0 10V η 6,6V ,6V ,5V ,5V ,5V = With condensation --- = Without condensation xtract 10V ,6V ,6V ,5V ,5V ,5V Surrounding SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With outside temperature -15 º and extract air temperature 25 º. With condensation: 50%Rh. Without condensation: 0%Rh. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. 10V ,6V ,6V ,5V ,5V ,5V

27 Performance TX06 xtract SP 2,5 SP 1,5 SP 2,0 10V V V ,2V ,2V ,7V = With condensation --- = Without condensation xtract 10V V V ,2V ,2V ,7V Surrounding SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With outside temperature -15 º and extract air temperature 25 º. With condensation: 50%Rh. Without condensation: 0%Rh. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. 10V V V ,2V ,2V ,7V

28 Hot water coil TX Topvex TX03 HWL Topvex TX04 HWL Topvex TX06 HWL Water temp. 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 ir flow m 3 /h Outdoor temp. 0 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -10 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -10 open by-pass air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -20 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -30 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -40 air temp Water flow l/s Pressure drop kpa apacity kw Topvex TX03 HWH Topvex TX04 HWH Topvex TX06 HWH Water temp. 60/30 60/30 60/40 60/40 60/30 60/30 60/40 60/40 60/30 60/30 60/40 60/40 ir flow m 3 /h Outdoor temp. 0 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -10 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -10 open by-pass air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -20 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -30 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -40 air temp Water flow l/s Pressure drop kpa apacity kw

29 Heater battery, electric TX Topvex TX03 Topvex TX04 Topvex TX06 apacity, kw ir flow, m 3 /h air temp. air temp. air temp. 0 >30 > >30 > >30 > >30 > > > > > > > > > otted frame = open by-pass Outdoor n extract air temperature of 21 and a heat exchanger effi ciency of 55% has been used for the calculations below. In practice the heat exchanger effi ciency or extract air temperature may be higher, which may give a few degrees higher supply air temperatures than in the above tables. Outdoor Outdoor imensions TX 43 TX G TX TX øl H I J K øl N R (½") 29

30 imensions TX TX K R ½" Technical data TX TX03 L TX03 HW TX04 L TX04 HW TX06 L TX06 HW Voltage V 400V requency Hz Phase ~ 3N 1 3N 3N 3N 3N Input power, fan motors W 2 x x x x x x 1084 Input power, electrical heating battery kw use 3x x25 3x10 3x32 3x10 Weight kg ilter, supply air ilter, extract air

31 ccessories TX03-06 Topvex TX03 Topvex TX04 Topvex TX06 Repeater 1 0-R230K 0-R230K 0-R230K Shut-off damper Valve actuator QM QM QM Valve, 2-way STV15-1.0/0.63 STV15-1.6/1.0 STV15-2.1/1.6 Valve, 3-way STR15-1.6/1.0 STR15-2.1/1.6 STR15-2.7/2.1 ooling battery, water PGK PGK PGK ooling battery, X coil XR XR XR Step controller. X cooling 2 S2/ S2/ S2/ Plastic housing, step controller IP5 U-K U-K U-K Transformer 230/24 V PSS48 PSS48 PSS48 uct sensor TG-KH/PT1000 TG-KH/PT1000 TG-KH/PT1000 ombi grille VVX 250 VVX 315 VVX 400 Silencer L 250 L 315 LR Timer T 120 T 120 T 120 Presence detector IR24-P IR24-P IR24-P O 2 Room sensor (digital 1/0) O2RT-R O2RT-R O2RT-R Water-lock 3 Water-lock Water-lock Water-lock ilter 5 (extract air) T TR03 5 T TX04 5 T TX06 5 ilter 7 (supply air) T TX03 7 T TX04 7 T TX Used when distance between the unit and control panel is more than 10 meters. 2 (24V). onverts V signal to relay output. 3 When risk of condensation in outdoor air side of heat exchanger Model: TX03, TX04, TX06 Heating coil: electric = L, water = HW vailable power: TX03 L: 6kW TX03 HW: HWL - low power, HWH - high power TX04 L: 12kW TX04 HW: HWL - low power, HWH - high power TX06 L: 16kW TX06 HW: HWL - low power, HWH - high power Right or left model (The side were the supply air is located when viewed from access side) Ordering code TX 31

32 SR SX SR07-11 SX04-06 SR04-06 SX03 SR03 S Side connection R Rotating heat exchanger X ross flow heat exchanger Topvex SR/SX is a Plug and play air handling unit with a modern design intended for ventilating offices, day-care centres or used as zone ventilation in larger buildings e.g. schools. To meet the new restricted energy requirements with low SP (Specific an Power) Topvex is equipped with fan motors. -motors consume an average of 30% less energy than motors. In some applications, the saving can be 50% or more. SR has a non-removable rotating heat exchanger. Topvex SR is equipped with a high efficiency rotating heat exchanger with an efficiency of up to 85%. Rotating heat exchangers do not need condense water drainage and is therefore very flexible to install. Topvex SX with its crossflow heat exchanger is normally used where it is a requirement that the supply and exhaust air must be kept separated. The unit have an efficient de-icing function. Topvex SR/SX units have energy saving functions like: - Week schedule. - ool recovering to recover the chilliness in the extract air during warm season. If using an external cooling unit. - emand controlled airflow by using a O 2 /humidity sensor, movement detector etc. - Sum alarm output for central supervision of many units. entral supervision secures that incorrect operating, like dirty fi lters, detects early. 32

33 xplanatory sketch SR/SX SR03-06 H O OS H RM RG S TS U T OT PS SS xtract fan RG Rotor guard S fan U Unit control SS air temp. sensor RM Rotor motor OS Outdoor air temp. sensor H Heater exchanger TS xtract air temp. sensor O amper outdoor air (accessories) T mergency thermostat H amper exhaust air (accessories) OT Overheating thermostat WV Water valve actuator (accessories) PS rost protection temp. sensor WV SR07-11 R H RM U Unit control OT Overheating thermostat (electric heater) S fan PS rost protection temp. sensor (hot water heater) xtract fan PTS Pressure transmitter supply air fan WV Water valve actuator (accessory) PT Pressure transmitter extract air fan H Heat exchanger SS air temp. sensor R Rotor control RM Rotor motor TS xtract air temp. sensor GS ilter pressure guard supply air OS Outdoor air temp. sensor G ilter pressure guard extract air HT Heater O amper outdoor air (accessory) T mergency thermostat (electric heater) H amper exhaust air (accessory) SX03-06 xtract fan S fan SS air temp. sensor OS Outdoor air temp. sensor TS xtract air temp. sensor LH lectrical re-heater battery T mergency thermostat OT Overheating thermostat WH Water heating battery PS rost protection temp. sensor amper by-pass U Unit control H Heat exchanger O amper outdoor air (accessory) H amper exhaust air (accessory) WV Water valve actuator (accessory) 33

34 Performance SR03 xtract SP 3,0 SP 2,0 SP 2,5 SP 1,5 10V η 10V V V V V xtract 10V V V V V V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V V V V V V

35 Performance SR04 xtract SP 3,0 SP 1,5 SP 2,0 SP 2,5 10V η 8V V V V V xtract 10V V V V V V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V V V V V V

36 Performance SR06 xtract SP 2,5 SP 2,0 SP 1,5 10V η 10V ,3V ,3V ,8V ,8V xtract 10V ,3V ,3V ,5V ,5V ,8V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V ,3V ,3V ,5V ,5V ,8V

37 Performance SR07 xtract SP 2,5 SP 2,0 SP 1,5 10V η 10V V V V V xtract 10V V V V V V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V V V V V V

38 Performance SR09 xtract SP 2,0 SP 2,5 SP 1,5 10V η 10V V V V V xtract 10V V V V V V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V V V V V V

39 Performance SR011 xtract SP 2,0 SP 2,5 SP 1,5 10V η 6,5V V V ,5V ,5V xtract 10V ,5V V V ,5V ,5V SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With air ratio 1:1 and air humidity at 50%. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. Surrounding 10V ,5V V V ,5V ,5V

40 Hot water coil SR03-06 n extract air temperature of 21 and a heat exchanger effi ciency of 70% has been used for the calculations below. In practice the heat exchanger effi ciency or extract air temperature may be higher, which may give a few degrees higher supply air temperatures than in the following tables. Topvex SR03 HWL Topvex SR04 HWL Topvex SR06 HWL Water temp. 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 ir flow m 3 /h Outdoor air temp. 0 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp. -10 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp. -20 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp. -30 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp. -40 air temp Water flow l/s Pressure drop kpa apacity kw Topvex SR03 HWH Topvex SR04 HWH Topvex SR06 HWH Water temp. 60/30 60/30 60/40 60/40 60/30 60/30 60/40 60/40 60/30 60/30 60/40 60/40 ir flow m 3 /h Outdoor temp. 0 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -10 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -20 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -30 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -40 air temp Water flow l/s Pressure drop kpa apacity kw

41 Hot water coil SR07-11 Topvex SR07 HWL Topvex SR09 HWL Topvex SR11 HWL Water temp. 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 ir flow m 3 /h Outdoor air temp 0 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp -10 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp -20 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp -30 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor air temp -40 air temp Water flow l/s Pressure drop kpa apacity kw Topvex SR03 apacity, kw ir flow, m 3 /h air temp. 0 >30 >30 > >30 > >30 > >30 > > Outdoor Topvex SR04 Topvex SR04 apacity, kw ir flow, m 3 /h air temp. air temp >30 >30 > >30 > >30 > > > Outdoor Heater battery, electric SR03-06 Topvex SR06 Topvex SR06 apacity, kw ir flow, m 3 /h air temp. air temp >30 >30 > >30 >30 > >30 > > > Outdoor Outdoor Outdoor 41

42 Heater battery, electric SR07-11 Topvex SR07 apacity kw ir flow m 3 /h air temp air temp Outdoor Topvex SR09 apacity kw ir flow m 3 /h air temp air temp Outdoor Outdoor Outdoor Topvex SR11 apacity kw ir flow m 3 /h Outdoor Outdoor Outdoor imensions SR ø315 SR03 15R ½" Min space to door 603 mm 42

43 imensions SR 62 G 15R ½" 111 K J H I I SR04-06 H G H I J K SR SR Min space to door 603 mm SR07-11 K L 15R (½") G M G K L M SR SR SR Min space to door 810 mm 43

44 Technical data SR SR03-L SR03-HW SR04-L SR04-HW SR06-L SR06-HW Voltage/requency V/50 Hz Phase ~ 3N 1 3N 3N 3N 3N Input power, motors W 2x508 2x508 2x1109 2x1109 2x1033 2x1033 Input power, el heating battery kw 6 6/12 9/16 use 3x x16/25 3x10 3x20/32 3x10 Weight kg ilter (/extract) 7/5 7/5 7/5 7/5 7/5 7/5 SR07 L SR07 HW SR09 L SR09 HW SR11 L SR11 HW Voltage/requency V/50Hz Phase - 3N 3N 3N 3N 3N 3N Input power, motors kw 2x1.03 2x1.03 2x1.90 2x1.90 2x3.07 2x3.07 Input power, heater battery kw 3/12* 4.5/15* 6/12*/24* use, unit 3x10 3x10 3x16/10 3x10 3x20/16/16 3x16 use, heaters (with seperate power supply) -/3x20 -/3x25 -/3x20/35 Weight kg ilter (/extract) 7/5 7/5 7/5 7/5 7/5 7/5 * lectric heater (above 6 kw has seperate incoming power supply) ccessories SR03-06 Topvex SR03 Topvex SR04 Topvex SR06 Repeater 1 0-R230K 0-R230K 0-R230K Outdoor set 2 OS SR04 OS SR06 Shut-off damper Valve actuator QM QM QM Valve, 2-way STV15-0,63 STV15-1,0 STV15-1,0 Valve, 3-way STR15-1,0 STR15-1,6 STR15-1,6 ooling battery, water PGK PGK PGK ooling battery, X coil XR XR XR Step controller. X cooling S2/ S2/ S2/ Plastic housing, step controller IP54 U-K U-K U-K Transformer 230/24 V PSS48 PSS48 PSS48 ombi grille VVX 315 VVX 400 VVX 500 Silencer L 315 LR LR Timer T 120 T 120 T 120 Presence detector IR24-P IR24-P IR24-P O 2 Room sensor (digital 1/0) O2RT-R O2RT-R O2RT-R ilter 5 (extract air) RO SR03 5 RO SR04 5 RO SR06 5 ilter 7 (supply air) RO SR03 7 RO SR04 7 RO SR Used when distance between the unit and control panel is more than 10 meters 2 Outdoor/xhaust air hood + Roof 44

45 ccessories SR07-11 Topvex SR07 Topvex SR09 Topvex SR11 Repeater 1 0-R230K 0-R230K 0-R230K -Tool cable T T T Outdoor set 2 OS SR07 OS SR09 OS SR11 Shut-off damper Valve actuator QM QM QM Valve, 2-way STV STV STV Valve, 3-way STR15-2,1 STR15-2,1 STR15-2,7 ooling battery, water PGK PGK PGK ooling battery, X coil XR XR XR Silencer LR LR LR Timer T 120 T 120 T 120 Room temperature sensor TG-R5/PT1000 TG-R5/PT1000 TG-R5/PT1000 Outdoor sensor, wall mount TG-UH/PT1000 TG-UH/PT1000 TG-UH/PT1000 uct sensor TG-KH/PT1000 TG-KH/PT1000 TG-KH/PT1000 Presence detector IR24-P IR24-P IR24-P O 2 Room sensor (digital 1/0) O2RT-R O2RT-R O2RT-R O 2 Room sensor (analog V ) O2RT O2RT O2RT U-tube manometer, fi lter guard MRO MRO MRO ilter 5, or xtract bag fi lter (2pcs/unit) RO SR07 5 RO SR09 5 RO SR11 5 ilter 7, or xtract bag fi lter (2pcs/unit) RO SR07 7 RO SR09 7 RO SR Used when distance between the unit and control panel is more than 10 meters 2 Outdoor/xhaust air hood + Roof SR03-06 Model: SR03, SR04, SR06 Heating coil: electric = L, water = HW vailable power: SR03 L: 6kW SR03 HW: HWL - low power, HWH - high power SR04 L: 6kW alt. 12kW SR04 HW: HWL - low power, HWH - high power SR 06 L: 9kW alt. 16kW SR06 HW: HWL - low power, HWH - high power Right or left model (the side were the supply air is located when viewed from access side) Ordering code SR SR07-11 Model: SR07, SR09, SR11 Heating coil: electric = L, water = HWL vailable power: SR07 L: 3kW alt. 12kW SR07 HW: HWL - low power SR09 L: 4,5kW alt. 15kW SR09 HW: HWL - low power SR11 L: 6kW alt. 12kW or 24kW SR11 HW: HWL - low power Right or left model (access side as viewed looking in the direction of the supply air) xtract duct, top or side connection V or VV airflow controlling (V= onstant ir Volume, VV= Variable ir Volume) ommunication to MS systems LON xoline/uilt-in Web via TP/IP 45

46 Performance SX03 xtract SP 2,5 SP 1,5 SP 2,0 10V η 10V ,5V ,5V ,6V ,6V = With condensation --- = Without condensation xtract 10V V ,5V ,5V ,6V ,6V Surrounding SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With outside temperature -15 º and extract air temperature 25 º. With condensation: 50%Rh. Without condensation: 0%Rh. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. 10V V ,5V ,5V ,6V ,6V

47 Performance SX04 xtract SP 1,5 SP 2,0 SP 2,5 10V ,6V η 6,6V ,5V ,5V ,7V = With condensation --- = Without condensation xtract 10V ,6V ,6V ,5V ,5V ,7V Surrounding SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With outside temperature -15 º and extract air temperature 25 º. With condensation: 50%Rh. Without condensation: 0%Rh. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. 10V ,6V ,6V ,5V ,5V ,

48 Performance SX06 xtract SP 2,5 SP 2,0 SP 1,5 10V V V V V V = With condensation --- = Without condensation xtract 10V V V V V V Surrounding SP = Specific an Power (kw/m 3 /s) The SP value stated applies to the complete unit. Thermal efficiency With outside temperature -15 º and extract air temperature 25 º. With condensation: 50%Rh. Without condensation: 0%Rh. Sound data The sound data tables indicate the sound power level L w, which should not be confused with the sound pressure level. 10V V V V V V

49 Hot water coil SX Topvex SX03 HWL Topvex SX04 HWL Topvex SX06 HWL Water temp. 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 60/40 70/50 80/60 90/70 ir flow m 3 /h Outdoor temp. 0 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -10 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -10 open by-pass air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -20 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -30 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -40 air temp Water flow l/s Pressure drop kpa apacity kw Topvex SX03 HWH Topvex SX04 HWH Topvex SX06 HWH Water temp. 60/30 60/30 60/40 60/40 60/30 60/30 60/40 60/40 60/30 60/30 60/40 60/40 ir flow m 3 /h Outdoor temp. 0 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -10 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -10 open by-pass air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -20 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -30 air temp Water flow l/s Pressure drop kpa apacity kw Outdoor temp. -40 air temp Water flow l/s Pressure drop kpa apacity kw otted frame = open by-pass 49

50 Heater battery, electric SX Topvex SX03 Topvex SX04 Topvex SX06 apacity, kw ir flow, m 3 /h air temp. air temp. air temp. 0 >30 > >30 > >30 > >30 > > > > > > > > > > Outdoor otted frame = open by-pass n extract air temperature of 21 and a heat exchanger effi ciency of 55% has been used for the calculations below. In practice the heat exchanger effi ciency or extract air temperature may be higher, which may give a few degrees higher supply air temperatures than in the above tables. Outdoor Outdoor imensions SX SX Min space to door 630 mm ø SX04-06 Min space to door 698/824 mm G H I J K L X Y Z SX SX

51 Technical data SX SX03 L SX03 HW SX04 L SX04 HW SX06 L SX06 HW Voltage/requency V/50 Hz Phase ~ 3N 1 3N 3N 3N 3N Input power, motors W 2x496 2x496 2x1069 2x1069 2x1052 2x1052 Input power, el heating battery kw use 3x x25 3x10 3x32 3x10 Weight kg ilter (/extract) 7/5 7/5 7/5 7/5 7/5 7/5 ccessories SX Topvex SX03 Topvex SX04 Topvex SX06 Repeater 1 0-R230K 0-R230K 0-R230K Shut-off damper Valve actuator QM QM QM Valve, 2-way STV15-1.0/0.63 STV15-1.6/1.0 STV15-1.6/1.6 Valve, 3-way STR15-1.6/1.0 STR15-2.1/1.6 STR15-2.7/2.1 ooling battery, water PGK PGK PGK ooling battery, X coil XR XR XR Step controller. X cooling S2/ S2/ S2/ Plastic housing, step controller IP54 U-K U-K U-K Transformer 230/24 V PSS48 PSS48 PSS48 ombi grille VVX 315 VVX 400 VVX 500 Silencer L 315 LR LR Timer T 120 T 120 T 120 Presence detector IR24-P IR24-P IR24-P O 2 Room sensor (digital 1/0) O2RT-R O2RT-R O2RT-R Water-lock 2 Water-lock Water-lock Water-lock ilter 5 (extract air) RO SR03 5 T SX04 5 T SX06 5 ilter 7 (supply air) RO SR03 7 T SX04 7 T SX Used when distance between the unit and control panel is more than 10 meters 2 When risk of condensation in outdoor air side of heat exchanger Model: SX03, SX04, SX06 Heating coil: electric = L, water = HW vailable power: SX03: 6kW SX03 HW: HWL - low power, HWH - high power SX04: 12kW SX04 HW: HWL - low power, HWH - high power SX06: 16kW SX06 HW: HWL - low power, HWH - high power Right or left model (The side were the supply air is located when viewed from access side) Ordering code SX 51

52 unctions included in the Standard, 17S controller: Menu Languages Temperature control ir flow control an control Heat exchanger control Re-heater control old water cooler control X cooling control ool recovering Night cooling (free cooling) emand ventilation xtended running Week schedule amper control larm ommunication More than 20 different languages. onstant supply air. onstant supply air with outdoor temp. compensation. xtract air (cascade). Week timer, two separate running periods/twenty-four hours. Stepless settable between 0-100%. Transformer control. Rotating heat exchanger (on/off). y-pass damper, cross/counter flow exchanger (stepless). Hot water coil (0...10V control signal). lectric heating. xternal coil (0...10V control signal). xternal coil (Step controller S2/ is required, accessory). utomatically recovers the cold in the indoor air to cool down the warmer outdoor air. Night/ree cooling is used during the summer to cool the building night-time by using cool outdoor air, thereby reducing the need for cooling during the day and thereby saving energy. The units have one digital input for extended/forced running using an external signal, e.g. an external timer, movement detector, O 2 -sensor or similar sensor with a voltage free contact. xtended/forced running is when the unit goes from shut down mode, low or medium fanspeed to the chosen fan speed. The units have a digital input for extended/forced running. The function activates by using an external signal from e.g. a push button or a timer. The function can also be activated by using the control panel. xtended running can be set between minutes. Two separate running periods/week day. 24V output to control one or two shut-off dampers. larm messages in clear text. Sum alarm output (24V). ire alarm input (potential free contact). Stop the unit or continuous running. When more than 10 meter cable between the unit and control panel is needed a repeater (0-R accessory) can be used. One 0-R can control up to 6 HU's. Standard xoline and Modbus via RS 485. Option xoline via TP/IP. Option LON. 52

53 unctions included in the dvanced, 28 controller: Menu Languages Temperature control ir flow control an control Heat exchanger control Re-heater control old water cooler control X cooling control ool recovering Night cooling (free cooling) emand ventilation xtended running Yearly schedule amper control larm ommunication -tool software More than 20 different languages. air. air with outdoor temp. compensation. xtract air. ascaded room temperature control. Outdoor temperature dependent switching between room control and supply air control. Outdoor temperature dependent switching between exhaust air control and supply air control. Year-based clock function. This means that a week-schedule with holiday periods for a full year can be set. ach day has up to two individual running periods for normal speed and reduced speed. onstant air volume control, V. onstant duct pressure control, VV. Outdoor temperature compensated air volume/duct pressure. Rotating heat exchanger (stepless). y-pass damper, cross/counter flow exchanger (stepless). Liquid connected exchanger (0...10V control signal or by two digital outputs). Mixing dampers (0...10V control signal). Hot water coil (0...10V control signal). lectric heating. Hot water coil and lectric heating. xternal coil (0...10V control signal). xternal coil (Up to 3-step, binary control). utomatically recovers the cold in the indoor air to cool down the warmer outdoor air. Night/ree cooling is used during the summer to cool the building night-time by using cool outdoor air, thereby reducing the need for cooling during the day and thereby saving energy. In applications with varying occupancy the fan speeds or mixing dampers can be controlled by the air quality as measured by a O 2 -sensor. It is also possible to use a digital input for extended/forced running using an external signal, e.g. an external timer, movement detector or a similar sensor with a voltage free contact. The units have a digital input for extended/forced running. The function activates by using an external signal from e.g. a push button or a timer. The function can also be activated by using the control panel. xtended running can be set between minutes. Year-based clock function. This means that a week-schedule with holiday periods for a full year can be set. ach day has up to two individual running periods for normal speed and reduced speed. igital timer channels for door locks, lighting etc. 24V output to control one or two shut-off dampers. larm messages in clear text. larm priorities, alarms can be given different priority levels, -alarm, -alarm, -alarm or not active. Sum alarm output (24V). ire alarm input (potential free contact). ifferent fan control modes at fire. When more than 10 meter cable between the unit and control panel is needed a repeater (0- R accessory) can be used. One 0-R can control up to 6 HU's. Standard xoline and Modbus via RS 485. Option xoline/uilt-in Web via TP/IP. Option LON. P-based commissioning software. 53

54 ccessories amper for outdoor air ircular damper The circular damper consists of a tubular housing equipped with a damper blade pivoting on an axle. The blade fits into the circular duct. The connection ends are equipped with silicon rubber sealing rings. The damper is made from hot-dip galvanised sheet steel. The shut-off damper is prepared for external insulation and has arrows showing the damper blade position. Rectangular damper The rectangular multi-leaf damper comprises a number of opposed blades, swivelling on nylon bearings in a sheet metal framework. The blades are connected via a system of linkages (protected) on the outside of the frame. The damper is made of hot-dip galvanised sheet steel. The shut-off damper is prepared for external insulation and has arrows showing the damper blade position. Shutter damper is a shut-off damper suitable for Topvex. The damper is provided with 24V motors with spring-return actuators. are made in leakage performance class 3 according to N 1751:1998 nnex.2. Outdoor air dampers are used to prevent the hot water battery from freezing and also prevent cold air to chill down the building if the unit stops. is connected to terminals in the electrical connection box. Maintenance We recommend preventive maintenance of the damper twice per year for optimum performance. If the damper gets dirty, the blade/s should be cleaned. The gasket sealing should be checked and the blade/s axle/s lubricated as necessary. Pressure drop circular damper ps [Pa] m/s imensions circular damper ø ø Pressure drop rectangular damper imensions rectangular damper ombi grid VVX The ombi grid, suitable for mounting on an outside wall is produced from galvanised sheet steel, finished in dark grey enamel. The outside air intake, and exhaust air outlet are separated from each other so that the air cannot short circuit. our screws on the front facilitate dismantling for cleaning of the grid. Mounting: The back plate is first screwed and fitted to the wall. The grid can be mounted with exhaust-air outlet either on the right or on the left. VVX ø

55 ooling battery water WK, cold water-cooling battery for circular ducts. asing of galvanised sheet steel with copper tubes and aluminium fins. Inspection covers for easy cleaning and maintenance. onnection sleeves with rubber seal. Max working pressure 1.6 MPa (16 bar). Technical data WK ir ir ir ir ir ir apacity Water Water flow velocity pressure before before after flow pressure (m 3 /h) (m/s) drop (Pa) ( ) (% RH) ( ) (kw) (l/s) drop (kpa) < , ±1 ø ødy ±2 +8 R½" WK ø H ødy G K L Weight kg kg kg kg kg kg kg H±1 G±3 K±1 G±3 L±5 55

56 PGK PGK, cold water-cooling battery for rectangular ducts. asing of galvanised sheet steel with copper tubes and aluminium fins. ir vent and drain valve included. ondensation tray of stainless steel and condensate connection (R½"). Max working pressure 1.6 MPa (16 bar). or water connection left or right. Two inspection covers for cleaning and maintenance. roplet eliminator as an accessory regardless of air direction. Recommended for air velocities from 3 m/s. R½ H PGK H N R 3/4 40x R 3/4 50x R 3/4 50x R 3/4 60x30* R 3/4 60x35* R1 70x40* R1 80x50* R1 100x50* * use 2 pcs Technical data PGK Water temperature 6/12 ir ir ir ir ir ir Water Water flow velocity pressure before before after apacity flow pressure PGK (m 3 /h) (m/s) drop (0 ) (%RH) (0 ) (kw) (l/s) drop (kpa) m 3 /h m/s Pa 0 %RH 0 kw l/s kpa 400x x x x x x x x N! roplet eliminator must be ordered seperately. Pressure drop at page

57 QM Valve motor, water valve microprocessor based actuator controlled by a V signal from orrigo. voltage 24V. The actuator has automatic stroke adjustment. Technical data voltage ontrol signal Transformer size Stroke Stroke time orce mbient temp. Storage temp. mbient humidity able connection egree of protec. 24 V V 6 V 20 mm 5 s/mm 450 N % RH Screw terminals IP54 This product conforms to the M standard NL N och N STV/STR Water valve/heating water, 2/3-way STV/STR is a 2 and 3-way control valve to control the hotwater to the heating battery. They are intended for use together with the QM actuator. STV Technical data Max. difference pressure 1.6 Mpa. low charac. Square Media temp Media Hot, cold, glycol mixed water or steam onnection Metric female threaded Stroke 15 mm Max leakage 0.1 % by kv Pressure rat. PN16 Rangeabillity 50:1 Mat: ody Rg5* Mat: one Rg5* Stem Stainless steel Packing box Self-adjusting teflon * RG5 = gun metal SS 5204 STR QM 2-way Pressure drop 3-way 1 2 H Weight STV/STR G½" kg 122 The actuator depth is 92 mm mvp kpa kv 0,63 1,0 1,6 2,1 2,7 4,2 5, onnection nut Jam nut 1 0,5 0,4 0,3 0, N! The actuator and the valve have an overlap of approx 15 mm when connected. 0,1 1 0,01 0,05 0,1 0,2 0,3 0, l/s 0,05 0,1 0, m 3 /h 57

58 I HN XR uct coolers with X oil XR are used for central cooling of the ventilation air in ventilation systems. The XR is also used for individual cooling of the air supplied to individual rooms (zones). 8 standard sizes Same model for left-hand or righthand installation (reversible coil). Stainless steel condensate drip tray. droplet eliminator can be fitted regardless of the direction of air flow asily removable drip tray to simplify cleaning and inspection. roplet eliminator We recommend that a droplet eliminator should be installed on the outlet side of the coil if the air velocity is in excess of 2.5 m/s. This prevents water droplets being entrained by the air flow out into the duct system. The collected water is discharged through the stainless steel condensate drip tray. The droplet eliminator is easily accessible after the drip tray has been removed. Operating data Max. operating press.: 2.8 MPa (28 ar) The coils are tested for leakage. esign The casing is made of luzinc-coated sheet steel. The coil has copper tubes and aluminium fins. Stainless steel drip tray for collecting the condensate, with R½ drain connection. Removable drip tray for inspection and cleaning of the coil. Installation The XR is intended for installation in a horizontal duct, with the air flow in either direction (reversible coil). R S 9 ø10 (8x) 9 K M O 9 O R½" XR duct cooler H S R I O K M N roplet eliminator mm mm mm mm mm mm mm mm ø mm onnection R im XR 400x , /2" 40x20 XR 500x , /2" 50x25 XR 500x , /2" 50x30 XR 600x , /8" 60x30 XR 600x , /8" 60x35 XR 700x , /8" 70x40 XR 800x , /8" 80x50 XR 1000x , /8" 100x50 Pressure drop across droplet eliminator N! roplet eliminator must be ordered seperately. Pressre drop, p [Pa] ir velocity, v [m/s] 58

59 apacity, refrigerant R407, 5 º Standard sizes of XR The tables on the following pages give examples of the capacity for each size. If none of these is suitable, we shall be pleased to carry out a computer calculation. ir ir ir ir ir Refrigerant Refrigerant flow pressure drop in in out Output flow pressure drop XR (m 3 /h) (Pa) (º) (% RH) (º) (kw) (kg/h) (kpa) 400x ,8 2, ,8 3,2 75 6, ,9 2,7 63 4, ,4 3,9 90 8, ,5 2,8 65 4, ,2 4, ,3 500x ,8 3,4 80 3, , , ,9 4, ,1 6, , , , ,2 7, ,1 500x ,5 4, , ,3 6, , ,6 5, , ,8 7, , ,3 6, , ,9 8, ,7 600x ,4 5, , ,8 8, , ,5 6, , ,6 9, , ,3 7, , , ,5 600x , , ,4 8, , ,7 7, , , , ,4 8, , , ,6 700x ,7 8, , ,4 12, , ,3 9, ,3 14, , ,5 11, , ,2 16, x ,6 12, , ,3 18, , ,2 14, , ,1 21, , ,4 16, , ,2 24, ,9 1000x ,3 16, , ,9 23, ,9 18, ,6 29, , ,7 21, , ,9 31,

60 Systemair Inhouse studio 2009 rt no. 8077