Application of Radioactive Particle Tracking (RPT) and Densitometry for Measuring Liquid Velocity Fields and Void Fraction in Convective Boiling Flows
|
|
|
- Chad Jennings
- 6 years ago
- Views:
Transcription
1 ID: B01-04 Application of Radioactive Particle Tracking (RPT) and Densitometry for Measuring Liquid Velocity Fields and Void Fraction in Convective Boiling Flows Ashutosh Yadav 1, Harish Jagat Pant 2 and Shantanu Roy 1 1: Department of Chemical Engineering, Indian Institute of Technology - Delhi, New Delhi , India 2:Isotope and Radiation Application Division, Bhabha Atomic Research Centre, Mumbai , India
2 Introduction Boiling flows are observed in evaporators, boilers, distillation towers, chemical reactors, condensers, oil pipelines, nuclear reactors, electronic cooling. Phase change by boiling or evaporation is a highly efficient heat transport mechanism. Boiling flow is a complex multiscale phenomena. * 2
3 Nuclear Power Reactors Nuclear reactors produce thermal energy that can be converted into mechanical energy and ultimately, into electrical energy with the help of steam turbines. Main components: i. Core ii. Coolant iii. Containment iv. Moderator Main commercial nuclear reactors: Pressurized Water Reactor (PWR) Boiling Water Reactor (BWR) Forced Circulation Natural Circulation 3
4 Forced Convective Boiling Flow Vapor single-phase flow The liquid phase is completely evaporated. Mist flow A sharp decrease in the heat transfer coefficient. Annular flow Core of the flow consists of vapor only, and liquid adjacent to the walls. Slug flow Bubbles coalesce into slugs of vapor. Moderate mass qualities. Bubbly Flow Individual bubbles. Liquid single-phase flow Liquid is sub-cooled and heat transfer to the liquid is by forced convection. N. I. Kolev, Multiphase Flow Dynamics 4: Nuclear Thermal Hydraulics, Springer (2009). 4
5 Advanced Heavy Water Reactor (AHWR) India has developed the (AHWR), based on boiling water NC cooling, for exploiting the huge thorium reserves No need for the installation, operation and maintenance of pumping devices, e.g. recirculation pumps Large heat sink in the form of Gravity Driven Water Pool with an inventory of 7000 m 3 of water Sinha, R.K., and A. Kakodkar, Design and development of the AHWR the Indian Thorium fuelled innovative nuclear reactor, Nucl. Eng. Des., 236, 683(2006). 5
6 Experimental Setup-I
7 Experimental Setup-II Column Diameter = 12 cm Heater Rod diameter = 12mm
8 Heater Rods Arrangements (Experimental Setup-II) A B C D 8
9 Gamma-ray Densitometry ln( I ln( I TP vap ) ln( I ) ln( I liq liq ) ) Cs-137 2D schematic representation 3D schematic representation 9
10 Void Fraction Measurement (Experimental Setup-I) (a) Axial development of void fraction for =22.7 kw m -2 as function of different inlet liquid temperatures and inlet liquid mass flux of: (a) G=2.89 kg m -2 s -1 (b) G=6.94 g m -2 s -1. q " 10
11 Void Fraction Profiles (Single and Two Heater Rods) Single heater rod Two heater rods 0 plane 90 plane 11
12 Experimental setup for RPT Measurements
13 Liquid Velocity Measurements Using RPT (Vector Plots) Velocity vectors arrangement at inlet flow rate of 5LPH (a) T in = 50 C (for single heater rod), (b) T in = 70 C (for single heater rod). 13
14 Velocity Profiles (Single Rod-Setup-II) T in = 50 C T in = 70 C Inlet liquid flowrate=0.01 cm/s 14
15 Conclusions Maximum void fraction was observed away from the heater wall suggesting that vapor bubbles after departing from heater wall grows in size. With increase in liquid temperature or decrease in liquid flow rate the void fraction increased. Void fraction profiles in case of single rod were flatter as compared to other heater rods configurations. Peak in the axial liquid velocity profiles is observed in the region near to the central heater wall and axial liquid velocity decreases in a region away from the central heater wall region. Magnitude of axial liquid velocity as well as liquid kinetic energy increases with increase in inlet liquid temperature for both heater rods configuration. Recirculation of the liquid phase results in negative velocity magnitude for single and three heater rods configuration.
16
ANNEX V. AP600 & AP1000 Westinghouse Electric, USA
ANNEX V. AP600 & AP1000 Westinghouse Electric, USA Reactor System Reactor Type Power (MW th) Passive Safety Systems CORE/PRIMARY: Advanced Passive PWR (AP600) and (AP100) Westinghouse Electric, USA PWR
Secondary Systems: Condensate/Feedwater Cycle
Secondary Systems: Condensate/Feedwater Cycle K.S. Rajan Professor, School of Chemical & Biotechnology SASTRA University Joint Initiative of IITs and IISc Funded by MHRD Page 1 of 8 Table of Contents 1
Speransa 2008: Round table: Nuclear and sustainable development Universitad Politecnica de Valencia \UPV - Passive safety systems -
Universitad Politecnica de Valencia \UPV - Passive safety systems - complete+annex.doc 1 1.1 Definition of Passive Safety Systems...3 2. Passive safety systems for core decay heat removal....4 2.1 Pre-Pressurized
PASSIVE CONTAINMENT COOLING: MODEL EXPERIMENTS
Proceedings of the 21 st National & 10 th ISHMT-ASME Heat and Mass Transfer Conference December 27-30, 2011, IIT Madras, India ISHMT_IND_12_056 PASSIVE CONTAINMENT COOLING: MODEL EXPERIMENTS Someshwar
Pool boiling heat transfer enhancement on porous surface tube
Nuclear Science and Techniques 22 (2011) 122 128 Pool boiling heat transfer enhancement on porous surface tube LI Yong * YAN Changqi SUN Zhongning SUN Licheng College of Nuclear Science and Technology,
LEAKAGE MONITORING OF SEAL PLUG FOR INDIAN PRESSURIZED HEAVY WATER REACTOR BY PSYCHOMETRICS ANALYSIS METHOD
Proceedings of the National Seminar & Exhibition on Non-Destructive Evaluation NDE 2011, December 8-10, 2011 LEAKAGE MONITORING OF SEAL PLUG FOR INDIAN PRESSURIZED HEAVY WATER REACTOR BY PSYCHOMETRICS
Thermal Design of Condenser Using Ecofriendly Refrigerants R404A-R508B for Cascade Refrigeration System
Thermal Design of Condenser Using Ecofriendly Refrigerants R404A-R508B for Cascade Refrigeration System A D Parekh, and P R Tailor Abstract Because of damaging effect of CFC refrigerants on stratospheric
Physical Mechanism of Convection. Conduction and convection are similar in that both mechanisms require the presence of a material medium.
Convection 1 Physical Mechanism of Convection Conduction and convection are similar in that both mechanisms require the presence of a material medium. But they are different in that convection requires
MECHANICAL SCIENCE Module 2 Heat Exchangers
Department of Energy Fundamentals Handbook MECHANICAL SCIENCE Module 2 Heat Exchangers Heat Exchangers DOE-HDBK-1018/1-93 TABLE OF CONTENTS TABLE OF CONTENTS LIST OF FIGURES... ii LIST OF TABLES... iii
MODULE 6 HUMIDIFICATION AND AIR CONDITIONING
MODULE 6 HUMIDIFICATION AND AIR CONDITIONING LECTURE NO. 3 6.3 Humidification and dehumidification operations and design calculations Humidification operations: In this operation, water transfers from
CFD Analysis of a 24 Hour Operating Solar Refrigeration Absorption Technology
IJIRST International Journal for Innovative Research in Science & Technology Volume 1 Issue 11 April 2015 ISSN (online): 2349-6010 CFD Analysis of a 24 Hour Operating Solar Refrigeration Absorption Technology
American Nuclear Society (ANS)
What s New... American Nuclear Society (ANS) Project Initiation Notification System (PINS) ANS Standards Before work on a draft can begin, a Project Initiation Notification System (PINS) form must be approved
So far, we have covered the basic concepts of heat transfer and properties.
ET3034TUx - 6.2.2 - Solar thermal energy 2 - Solar thermal heating So far, we have covered the basic concepts of heat transfer and properties. Now we are going to discuss the applications of these concepts
CHAPTER I INTRODUCTION. In the modern life, electronic equipments have made their way
1 CHAPTER I INTRODUCTION In the modern life, electronic equipments have made their way in to practically every part, which is from electronic gadgets to high power computers. Electronic components have
HEAT REMOVAL TESTS FOR THE HIGH PERFORMANCE VAULT STORAGE SYSTEM OF SPENT NUCLEAR FUEL
HEAT REMOVAL TESTS FOR THE HIGH PERFORMANCE VAULT STORAGE SYSTEM OF SPENT NUCLEAR FUEL M. Oda*, M. Shimizu*, N. Kumagai*, H. Kanai**, M. Tanabe** *Nuclear Fuel Cycle Group, Power & Industrial Systems R&D
A STUDY ON THE BEHAVIOR OF STEAM CONDENSATION IN U-SHAPED HEAT TUBE
A STUDY ON THE BEHAVIOR OF STEAM CONDENSATION IN U-SHAPED HEAT TUBE Satoru Ito 1, Keisuke Tsukada 1, Nobuyoshi Tsuzuki 2, Takao Ishizuka 3 and Hiroshige Kikura 3 1 Department of nuclear Engineering, Graduate
International Journal of Engineering Research (IJOER) [Vol-1, Issue-3, June- 2015]
![International Journal of Engineering Research (IJOER) [Vol-1, Issue-3, June- 2015]](/thumbs/86/93674748.jpg "International Journal of Engineering Research (IJOER) [Vol-1, Issue-3, June- 2015]")
Experimental Investigation To Develop The Refrigeration System With Two Phases Condensing Ejector Along With Energy Saving Anjani Kumar 1, Kuldip Kumar 2, Ujjwal Kumar Nayak 3 123 Department of mechanical
THERMODYNAMICS STEAM P7690 AND STEAM BENCHES CUSSONS TECHNOLOGY LABORATORY RECOMMENDATION
cussons TECHNOLOGY THERMODYNAMICS STEAM P7690 AND STEAM BENCHES CUSSONS TECHNOLOGY LABORATORY RECOMMENDATION Thermodynamics is a branch of physical science concerned with the inter-relationship and inter-conversion
Investigation of Evaporator Performance with and without Liquid Overfeeding
Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2016 Investigation of Evaporator Performance with and without Liquid Overfeeding
14 Drying. I Basic relations and definitions. Oldřich Holeček, Martin Kohout
14 Drying Oldřich Holeček, Martin Kohout I Basic relations and definitions Drying is a process which is used for removing the liquid from the solid material. In standard chemical engineering practice drying
PIPING SYSTEM EQUIPMENTS
PIPING SYSTEM EQUIPMENTS Introduction Equipments are devices that provide power, process and store materials. Equipments in piping systems depend on the specific industries using them. Specialized equipment
Laser Weld Keyhole Dynamics and Control. M. H. Cho, D.F. Farson Welding Engineering Department, The Ohio State University, Columbus, Ohio
Laser Weld Keyhole Dynamics and Control M. H. Cho, D.F. Farson Welding Engineering Department, The Ohio State University, Columbus, Ohio I. INTRODUCTION Porosity formation is a major problem that limits
Performance of Shell and Tube Heat Exchanger under Varied Operating Conditions
Performance of Shell and Tube Heat Exchanger under Varied Operating Conditions N. Prabhu Kishore 1, N. Alekhya 2, J. Ugandhar 3 Asst. Professor, Department of Mechanical Engineering, MLR Institute of Technology,
Effect of Parameters on Internal Flow Patterns of a Top Heat Mode Closed-loop Oscillating Heat Pipe with Check Valves (THMCLOHP/CV)
Australian Journal of Basic and Applied Sciences, 5(7): 638-643, 2011 ISSN 1991-8178 Effect of Parameters on Internal Flow Patterns of a Top Heat Mode Closed-loop Oscillating Heat Pipe with Check Valves
STUDY OF HEAT TRANSFER IN A CORRUGATED PLATE HEAT EXCHANGER USING AL 2 O 3 MICROPARTICLES
International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 4, July Aug 216, pp.189 195, Article ID: IJMET_7_4_19 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=4
EXPERIMENTAL INVESTIGATIONS ON AL 2 O 3 NANO REFRIGERANT WITH DIFFUSER AT CONDENSER INLET IN A VCR SYSTEM
EXPERIMENTAL INVESTIGATIONS ON AL 2 O 3 NANO REFRIGERANT WITH DIFFUSER AT CONDENSER INLET IN A VCR SYSTEM 1 RONANKI SURESH, 2 Dr. K. KALYANI RADHA 1 M.Tech, Mechanical Engineering, JNTUA College of Engineering
MAL-DISTRIBUTION MODEL OF HEAT EXCHANGERS IN MICRO CHANNEL EVAPORATOR
MAL-DISTRIBUTION MODEL OF HEAT EXCHANGERS IN MICRO CHANNEL EVAPORATOR Santhosh Kumar Student(M.Tech), Mechanical Dept Gokul group of institutions Visakhapatnam, India M Karteek Naidu ASST PROFF, Mechanical
Development of Post-Accident Monitoring System for Severe Accidents
Development of Post-Accident Monitoring System for Severe Accidents Chang-Hwoi Kim a, Sup Hur b, Kwang-Sub Son c, and Tong-Il Jang d a b c d Abstract: To cope with a severe accident such as Fukushima Nuclear
Using FDS Modelling to Establish Performance Criteria for Water Mist Systems on Very Large Fires in Tunnels
Using FDS Modelling to Establish Performance Criteria for Water Mist Systems on Very Large Fires in Tunnels Jack R. Mawhinney, P. Eng., FSFPE Javier J. Trelles, Ph.D. Authors & acknowledgement J. R. Mawhinney
In the name of God. Jami Institute of Jami - Mehdi Rasti
In the name of God 1 Heat Transfer Jami Institute of Technology Heat Exchangers part 2 Mehdi Rasti 2 The Counter-Flow Heat Exchanger In contrast to the parallel-flow exchanger, this configuration provides
B.Tech. First Semester Examination Basics of Mechanical Engineering (ME-101F)
B.Tech. First Semester Examination Basics of Mechanical Engineering (ME-101F) Q. 1. (a) Differentiate between water tube boiler and fire tube boiler. Ans. Comparison Between 'Fire-tube and Water tube'
Chapter 10. Passive Cooling Contents
Chapter 10. Passive Cooling Contents 10.1 Introduction to Cooling 10.2 Historical and Indigenous Use of Passive Cooling 10.3 Passive Cooling Systems 10.4 Comfort Ventilation VS Night Flush Cooling 10.5
CFD Analysis of Co-current Spray Dryer with Swirler at Air Inlet
CFD Analysis of Co-current Spray Dryer with Swirler at Air Inlet Bharath G Wadone #1, Dr. G Manavendra *2 # 1 PG Student: Dept. of Mechanical Engineering, *2 Associate Professor: Dept. of Mechanical Engineering,
Pressure drop analysis of evaporator using refrigerants R-22, R-404A and R-407C
drop analysis of evaporator using refrigerants R-22, R-404A and R-407C #1 Pallavi Sawkar, #2 Dr. Pradeep Patil #12 Department of Mechanical Engineering, JSPM s JSCOE, Savitribai Phule Pune University,
Homework Chapter2. Homework Chapter3
Homework Chapter2 2/1 A storage tank holds methane at 120 K, with a quality of 25 %, and it warms up by 5 C per hour due to a failure in the refrigeration system. How long time will it take before the
HEAT EXCHANGERS. Heat exchangers are broadly classified based on the following considerations.
HEAT EXCHANGERS INTRODUCTION The devices that are used to facilitate heat transfer between two or more fluids at different temperatures are known as heat exchangers. Different types and sizes of heat exchangers
INTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING AND TECHNOLOGY (IJMET) AN EXPERIMENTAL STUDY OF HEAT TRANSFER IN A CORRUGATED PLATE HEAT EXCHANGER
INTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING AND TECHNOLOGY (IJMET) International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 6340(Print), ISSN 0976 6340 (Print) ISSN 0976 6359
Closed Loop Pulsating Heat Pipe with a Hydrocarbon as Working Fluid: A Review
Closed Loop Pulsating Heat Pipe with a Hydrocarbon as Working Fluid: A Review Roshan D. Bhagat 1, Prof. K. M. Watt 2 1 Student M.E. Thermal Engineering, Prof. Ram Meghe Institute of Technology & Research
A Study of Heat Transfer Using Corrugated Al 2 o 3 microparticles
International Refereed Journal of Engineering and Science (IRJES) ISSN (Online) 2319-183X, (Print) 2319-1821 Volume 4, Issue 6 (June 2015), PP.110-115 A Study of Heat Transfer Using Corrugated Al 2 o 3
CHAPTER 2 EXPERIMENTAL APPARATUS AND PROCEDURES
CHAPTER 2 EXPERIMENTAL APPARATUS AND PROCEDURES The experimental system established in the present study to investigate the transient flow boiling heat transfer and associated bubble characteristics of
Performance analysis of a vapour compression refrigeration system with a diffuser for theeco-friendly refrigerants R-134a, R-600a and R-152a
International Journal of Research in Engineering and Science (IJRES) ISSN (Online): 2320-9364, ISSN (Print): 2320-9356 Volume 4 Issue 6 ǁ June. 2016 ǁ PP. 52-57 Performance analysis of a vapour compression
Fig.: macroscopic kinetic energy is an organized form of energy and is much more useful
Harnessing Energy Fig.: macroscopic kinetic energy is an organized form of energy and is much more useful Vapor Power Cycle The vast majority of electrical generating plants are variations of vapor power
EXPERIMENTAL INVESTIGATION OF WATER COOLER SYSTEM BY USING ECO-FRIENDLY REFRIGERANT (R-134a)
EXPERIMENTAL INVESTIGATION OF WATER COOLER SYSTEM BY USING ECO-FRIENDLY REFRIGERANT (R-134a) Abstract- With the recent government regulations, of banning the ozone depleting substances and Kyoto protocol
Division III Process Gas Treatment Equipment
ASME AG-1 Committee on Nuclear Air and Gas Treatment Division III Process Gas Treatment Equipment Chairman, SC Gas Process Treatment August 2008 - p 1 ASME AG-1 Division I General Requirements Division
An Instrumentation and Control for Loop Test
An Instrumentation and Control for Loop Test 21-24 Aug. 2012 S.H. Ahn, J.T. Hong, C.Y. Joung, S.J. Park Neutron Utilization Technology Division 0 Contents 1 Introduction Click to of add HANARO Title 2
Experimental Analysis on Effect of Design Parameters on the Performance of Single Loop Pulsating Heat Pipe
Experimental Analysis on Effect of Design Parameters on the Performance of Single Loop Pulsating Heat Pipe Someshwar S. Bhakre 1, Md. Rafik Sajjadahmad Choudhari 2 1, 2 PG Scholar, Mechanical Engineering
TITLE: Improvement in Heat Transfer Rate and Dynamics of Shrouded Fanned Radiator System
TITLE: Improvement in Heat Transfer Rate and Dynamics of Shrouded Fanned Radiator System Prof. G.L.Allampallewar 1, Divyal P. Bagul 2, Abhiraj S. Galande 3, Amol M. Rathod 4, Ketan R. Behere 5. 1 Assistant
EXPERIMENTAL PERFORMANCE INVESTIGATION OF SWIRLING FLOW ENHANCEMENT ON FLUIDIZED BED DRYER
EXPERIMENTAL PERFORMANCE INVESTIGATION OF SWIRLING FLOW ENHANCEMENT ON FLUIDIZED BED DRYER P. Sundaram and P. Sudhakar Department of Mechanical Engineering, SRM University, Kattankulathur, Chennai, India
Enhancement of COP in Vapour Compression Refrigeration System
Enhancement of COP in Vapour Compression Refrigeration System M. Krishna Prasanna #1 M.E student, Heat Transfer studies in Energy Systems Department of Mechanical Engg., Andhra University Visakhapatnam-530003,
Heat Exchanger. The purpose may be either to remove heat from a fluid or to add heat to a fluid.
HEAT EXCHANGERS Heat Exchanger Heat exchanger is an apparatus or an equipment in which the process of heating or cooling occurs. The heat is transferred from one fluid being heated to another fluid being
NUMERICAL SIMULATION OF VAPOUR COMPRESSION REFRIGERATION SYSTEM USING REFRIGERANT R152A, R404A AND R600A
NUMERICAL SIMULATION OF VAPOUR COMPRESSION REFRIGERATION SYSTEM USING REFRIGERANT R152A, R404A AND R600A [1] Ranendra Roy, [2] Madhu Sruthi Emani, [3] Bijan Kumar Mandal [1], [2],[3] Department of Mechanical
II. OBJECTIVE OF RESEARCH
Enhancement of Coefficient of Performance of Vapor Compression Refrigeration System Using Diffuser at let of Condenser Mr. Nurul Seraj 1, Dr. S. C. Roy 2 1 Student, 2 Head of Department, Department of
Operation Manual. Rad-1-Cloud_Precipitation-v1
Operation Manual Rad-1-Cloud_Precipitation-v1 M.H. Matthew Wong Y.W. Wong C.W. Ong Preface Rad-1-Cloud_Precipitation-v1 is an educational equipment for demonstrating (i) the generation of ionization tracks
Experimental investigation of Hybrid Nanofluid on wickless heat pipe heat exchanger thermal performance
Experimental investigation of Hybrid Nanofluid on wickless heat pipe heat exchanger thermal performance #1 Jaydev S. Bade, #2 Dr. Nitin U. Korde 1 Department of Mechanical Engineering, Savitribai Phule
COOPERATIVE PATENT CLASSIFICATION
CPC F COOPERATIVE PATENT CLASSIFICATION MECHANICAL ENGINEERING; LIGHTING; HEATING; WEAPONS; BLASTING (NOTE omitted) LIGHTING; HEATING F28 HEAT EXCHANGE IN GENERAL (NOTES omitted) F28D HEAT-EXCHANGE APPARATUS,
Davis Besse NPP Construction
Davis Besse NPP Construction Pushing Dirt and Digging Holes Actually started in 1969 below grade. When the AEC issued a Construction Permit (CP) above grade work could proceed. Below grade work was allowed
Drying rate 1. Section B to C of the curve, known as the constant rate periods, represents removal of unbound water from the product.
Drying rate 1 Drying process of a material can be described as a series of steps in which drying rate plays a key role. Following figure shows typical drying rate curve for a constant drying conditions.
HEAT PIPES
HEAT PIPES * Shaikh Naushad, Design Engineer PTC, Communication Concept, Saudi Arabia INTRODUCTION A heat pipe is a device that efficiently transports thermal energy from its one point to the other. It
Enhancement of COP using Nanoadditives in Domestic Refrigerator
ISSN 2395-1621 Enhancement of COP using Nanoadditives in Domestic Refrigerator #1 Mr.Sajjan Kawade, #2 Prof P.T.Kharat 1 sajjankawade@gmail.com 2 pradip5872@gmail.com #1 P.G. Student, Mechanical Engineering
Performance investigation of Air-conditioning system using ejector as expansion device
International Journal of Current Engineering and Technology E-ISSN 2277 416, P-ISSN 2347 161 216 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Research Article Performance
Internal flow Patterns of the Horizontal Heat Mode Closed-Loop Oscillating Heat Pipe with Check Valves (HHMCLOHP/CV)
Research Journal of Applied Sciences, Engineering and Technology 5(3): 865-869, 2013 ISSN: 2040-7459; E-ISSN: 2040-7467 Maxwell Scientific Organization, 2013 Submitted: June 13, 2012 Accepted: July 09,
2. MODELLING OF HEAT EXCHANGER THROUGH CATIA
ISSN (O): 2349-7084 International Journal of Computer Engineering In Research Trends Available online at: www.ijcert.org Heat Transfer Analysis of Helical Tubes Using Ansys and Catia Md Ameer Basha, Assoc.Prof.
Performance Enhancement of Inclined Bubbling Fluidized Bed Paddy Dryer by Design Modification
Performance Enhancement of Inclined Bubbling Fluidized Bed Paddy Dryer by Design Modification Phyu Phyu Thant, P. Mahanta, P.S. Robi Abstract Present paper discusses the bed inclination and passive inserts
Experimental Investigation of a Hybrid Evacuated Tube Solar Collector
International Conference on Mechanical, Industrial and Materials Engineering 2015 (ICMIME2015) 11-13 December, 2015, RUET, Rajshahi, Bangladesh Paper ID: ET-46 Experimental Investigation of a Hybrid Evacuated
Feasibility Study of Condensation Heat Exchanger with Helical Tubes for a Passive Auxiliary Feedwater System
Feasibility Study of Condensation Heat Exchanger with Helical Tubes for a Passive Auxiliary Feedwater System Kwanghee Seo 1) and Taewan Kim 2)* 1) KEPCO Engineering & Construction Company. INC., 269 Hyeoksin-ro,
PERFORMANCE OF WATER FILLED THERMOSYPHONS BETWEEN OC
Frontiers in Heat ipes Available at www.thermalfluidscentral.org ERFORMANCE OF WATER FILLED THERMOSYHONS BETWEEN 30-150OC K. S. Ong* and Christopher Lim Department of Industrial Engineering, Universiti
Products for. Nuclear Power Applications
Products for Nuclear Power Applications Caloritech electric heaters, heating elements and heating accessories are well-known in the industry for their quality, reliability, performance and versatility.
EXPERIMENTAL STUDY OF CENTRIFUGAL HUMIDIFIER FITTED IN AN INDUSTRIAL SHED LOCATED IN TROPICAL CLIMATES
THERMAL SCIENCE, Year 2011, Vol. 15, No. 2, pp. 467-475 467 EXPERIMENTAL STUDY OF CENTRIFUGAL HUMIDIFIER FITTED IN AN INDUSTRIAL SHED LOCATED IN TROPICAL CLIMATES by Krishnasamy SENTHILKUMAR a* and Pss
INTERNATIONAL JOURNAL OF RESEARCH IN AERONAUTICAL AND MECHANICAL ENGINEERING
ISSN (ONLINE): 2321-3051 INTERNATIONAL JOURNAL OF RESEARCH IN AERONAUTICAL AND MECHANICAL ENGINEERING Heat Transfer Enhancement Techniques in Two Phase Closed Thermosyphon: A Review Faddas Nikhil A. 1,
Global Journal of Engineering Science and Research Management
EXPERIMENTAL AND THEORETICAL STUDY OF MINIATURE VAPOR COMPRESSION CYCLE USING MICROCHANNEL CONDENSER Issam M. Ali Aljubury*, Ahmed Q. Mohammed, Marwa S. Neama * Mechanical Eng. Dept. College of Engineering,
More heat energy means more of what type of energy? Does the mass change? So, what must change? What is the same in both containers?
Quest Chapter 21-23 # Problem Hint 1 When a container of gas is heated, what happens to the average speed of its molecules? 1. Additional information is needed. 2. increases 3. doesn t change 4. decreases
IJIRST International Journal for Innovative Research in Science & Technology Volume 1 Issue 12 May 2015 ISSN (online):
IJIRST International Journal for Innovative Research in Science & Technology Volume 1 Issue 12 May 2015 ISSN (online): 2349-6010 Githin V Sam Jethin Babu Jesvin Sam Jithin Victor Abstract Loop heat pipes
DESIGN, DEVELOPMENT AND TESTING OF CROSS FLOW CIRCULAR HEAT PIPE TO COOLING OF OIL
DESIGN, DEVELOPMENT AND TESTING OF CROSS FLOW CIRCULAR HEAT PIPE TO COOLING OF OIL Vishnupant J. Sargar 1, Pruthveeraj D. Mali 2 1,2 Asst. Prof. Department of Mechanical Engineering, Adarsh Institute of
APPLICATION OF MINI HEAT PIPES FOR THERMAL MANAGEMENT OF OPTO-ELECTRONIC INSTRUMENTS
16th International Heat Pipe Conference (16th IHPC) Lyon, France, May 20-24, 2012 APPLICATION OF MINI HEAT PIPES FOR THERMAL MANAGEMENT OF OPTO-ELECTRONIC INSTRUMENTS Sandeep Kumar Singh, Sameer Khandekar
Experimental investigation of the dynamic thermohydraulic behaviour of vertical tube reboilers
Journal of Physics: Conference Series Experimental investigation of the dynamic thermohydraulic behaviour of vertical tube reboilers To cite this article: M Kessler and S Kabelac 2012 J. Phys.: Conf. Ser.
Refinery Vacuum Towers. State of the Art. (Extended Abstract)
Paper 357b Refinery Vacuum Towers State of the Art (Extended Abstract) Andrew W. Sloley CH2M HILL 21 Bellwether Way, Unit 111 Bellingham, WA 98225 Prepared for Presentation at the American Institute of
Solution of I Mid Term Steam Engineering 6ME5A
1(a) Discuss the working principle of LaMont high pressure boiler This boiler works on basic principle of forced convection. If the water is circulate by a pump inside the tube, the heat transfer rate
Dhulapally, Secunderabad Subject: REFRIGERATION AND AIR CONDITIONING QUESTION BANK
St.MARTIN S ENGINEERING COLLEGE Dhulapally, Secunderabad-500 014 Subject: REFRIGERATION AND AIR CONDITIONING Class : ECE III 1 Define Unit of refrigeration. 2 Define C.O.P. QUESTION BANK 3 What is the
Evaporation is a special case of heat transfer to a boiling liquid.
Evaporator Evaporation is a special case of heat transfer to a boiling liquid. Evaporation occurs at the liquid vapor interface when the vapor pressure is less than the saturation pressure of the liquid
IJARI. 1. Introduction: Heat Pipes. Volume 3, Issue 3 (2015) ISSN International Journal of Advance Research and Innovation.
Thermodynamic Analysis of Heat Pipe Using Ammonia, Water and Ethanol with a View to Being Used in Refrigeration Ankit Dwivedi, R. S. Mishra Department of Mechanical Engineering, Delhi Technological University,
Refrigerator/Heat pump
UMEÅ UNIVERSITY 2013-12-16 Department of Physics Leif Hassmyr Updates versions Joakim Ekspong 2017-10-31 Refrigerator/Heat pump 1 Task 1. Understand the principle of a refrigerator/heat pump and know its
KBC Petro-SIM Design Tools Integrated Equipment Operations. Al Shelton - KBC
KBC Petro-SIM Design Tools Integrated Equipment Operations Al Shelton - KBC 2012 KBC Advanced Technologies PROPRIETARY plc. All INFORMATION Rights Reserved. July 2012 Petro-SIM Design Tools KBC has completed
Performance Study of Triple Concentric Pipe Heat Exchanger
Performance Study of Triple Concentric Pipe Heat Exchanger #1 Pravin M. Linge, #2 A. B. Korane, #3 V. N. Kapatkar #123 Mechanical Engineering Department, Sinhgad College of Engineering, SPPU, Pune, India
International Engineering Research Journal Experimental Investigation of Effect of length on Performance of Axially Grooved Heat Pipe.
Experimental Investigation of Effect of length on Performance of Axially Grooved Heat Pipe. Anuradha V. Patil., Dr. Pradeep A. Patil. Department of Mechanical Engineering, JSPMs JSCOE, Hadapsar, Pune,
Thermal Management by Immersion Cooling
Volume 1 Issue 12 January 2008 The newsletter for The Thermal management of electronics In this issue: 1 Future Cooling 7 Thermal Minutes 14 Thermal Analysis future cooling Thermal Management by Immersion
Appendix A. Glossary of Common Terms
Glossary of Common Terms Glossary of Common Terms Absorption chiller A refrigeration machine using heat as the power input to generate chilled water. Adjustable speed drive A means of changing the speed
AND AIR-CONDITIONING. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University
Chapter 14 GAS VAPOR MIXTURES AND AIR-CONDITIONING Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University 2 Objectives Differentiate between dry air and atmospheric air. Define and calculate
Techniques of Heat Transfer Enhancement and their Application. Chapter 4. Performance Evaluation Criteria for Two-Phase Heat Exchangers
Chapter 4 Performance Evaluation Criteria for Two-Phase Heat Exchangers Prof. Min Zeng 1/50 1. Introduction 2. Operating Characteristics of Two-phase Heat Exchangers 3. Enhancement in Two-Phase Heat Exchange
Modeling and Simulation of Axial Fan Using CFD Hemant Kumawat
Modeling and Simulation of Axial Fan Using CFD Hemant Kumawat Abstract Axial flow fans, while incapable of developing high pressures, they are well suitable for handling large volumes of air at relatively
Modeling Solids Dryers and Granulators with Aspen Plus V8
Modeling Solids Dryers and Granulators with Aspen Plus V8 Ajay Lakshmanan and Claus Reimers Product Management, AspenTech Hosted by: Julie Levine and Ron Beck, Product Marketing, AspenTech Solids Process
Nuclear Electric Heating
Nuclear Electric Heating Caloritech has exceeded the most demanding nuclear heating requirements for over 30 years. We design and manufacture products for nuclear applications in PWR, BWR and PHWR nuclear
Numerical Stability Analysis of a Natural Circulation Steam Generator with a Non-uniform Heating Profile over the tube length
Numerical Stability Analysis of a Natural Circulation Steam Generator with a Non-uniform Heating Profile over the tube length HEIMO WALTER Institute for Thermodynamics and Energy Conversion Vienna University
Flow and heat transfer in a closed loop thermosyphon Part II experiment al simulation
Journal of Energy in Southern Africa 18(4): 41 48 DOI: http://dx.doi.org/10.17159/2413-3051/2007/v18i4a3393 Flow and heat transfer in a closed loop thermosyphon Part II experiment al simulation J C Ruppersberg
A Study of the Condenser in Nuclear Power Plants
International Journal of ChemTech Research CODEN (USA): IJCRGG, ISSN: 0974-4290, ISSN(Online):2455-9555 Vol.10 No.14, pp 09-16, 2017 A Study of the Condenser in Nuclear Power Plants * 1 S.Anandan, 2 R.Rajesh,
ME 410 MECHANICAL ENGINEERING SYSTEMS LABORATORY MASS & ENERGY BALANCES IN PSYCHROMETRIC PROCESSES EXPERIMENT 3
ME 410 MECHANICAL ENGINEERING SYSTEMS LABORATORY MASS & ENERGY BALANCES IN PSYCHROMETRIC PROCESSES EXPERIMENT 3 1. OBJECTIVE The objective of this experiment is to observe four basic psychrometric processes
Science 7 Chapter 6 Section 1
Science 7 Chapter 6 Section 1 Processes of Transferring Heat Processes of Heat Transfer There are 3 processes responsible for heat transfer: 1) Conduction 2) Convection 3) Radiation 1 Conduction Conduction:
Finned Heat Sinks for Cooling Outdoor Electronics under Natural Convection
Finned s for Cooling Outdoor Electronics under Natural Convection Lian-Tuu Yeh, Ph D & PE Thermal Consultant, Dallas, TX, 75252 USA Abstract For tower or poled mounted electronics, the heat sink weight
Technically Driven Heat Exchangers
JC Equipments Pvt. Ltd Technically Driven Heat Exchangers Profile JC is the leading ISO-9001-2008 certified, ASME U & S Stamp Authorized Designer, Manufacturer and Exporter of Industrial Cooling Towers
There are a number of factors in a process which may result in liquid entrainment. Some of the commonly observed causes are discussed below.
MIST ELIMINATORS MIST ELIMINATION In the chemical process industry there are a number of processes where gases and liquids come into contact with each other and whenever this happens the gas will entrain
FLIGHT UNLOADING IN ROTARY SUGAR DRYERS. P.F. BRITTON, P.A. SCHNEIDER and M.E. SHEEHAN. James Cook University
FLIGHT UNLOADING IN ROTARY SUGAR DRYERS By P.F. BRITTON, P.A. SCHNEIDER and M.E. SHEEHAN James Cook University Paul.Britton@jcu.edu.au, Phil.Schnieder@jcu.edu.au, Madoc.Sheehan@jcu.edu.au Keywords: Drying,