Quantum Waterside Fan Coil Specification 2. Mounting 3. Pipework Connections 3. Duct Connections 3. Electrical Connections 4.

Transcription

1

2 CONTENTS Page Quantum Waterside Fan Coil Specification 2 Mounting 3 Pipework Connections 3 Duct Connections 3 Electrical Connections 4 Controls 4 Fan Speed Settings 5 Periodic Maintenance 6 Fancoil Maintenance 7 Coil Water Content 8 Weights 8 Minimum No. Spigots 8 Coil Connections 8 Wiring Diagram 9 Fault Finding 10 Spares List 11 EUOVENT CETIFIED PEFOMANCE Manufacturer reserves the right to change any product specifications without notice. 1

3 QUANTUM WATESIDE FAN COIL SPECIFICATION Casings The casings shall consist of durable 1.2mm galvanised sheet steel reinforced where required to form a rigid structure. Discharged Plenum The discharge plenum shall be lined with class 0 acoustic insulation. The plenum shall be provided with spigots for duct connection. Drip Tray The drip tray shall be manufactured such that when the unit is mounted level there shall be a positive fall for the condensate water to the drain connection from all areas of the drip tray. There shall be no areas where water can collect in pools. The drip tray shall be insulated with 3mm closed cell foam to Class 0 specification. Fans Double inlet double width fans shall be used driven by a motor using cradle type resilient mountings. The fans impellers shall be at least 160mm diameter and of Tablock construction to ensure good performance and low noise. Each impeller shall be statically & dynamically balanced. Motors Motors shall be single speed permanent split capacitor type. The motors used shall comply with BS 5000 Part (revised 1989). Speed control shall be achieved by applying a variable voltage to the motor winding. Motors are to have maintenance free sealed for life bearings and built in thermal overload protec - tion. Heat Exchangers All heat exchangers shall be tested at a minimum of 25 bar pressure. The coils shall be manufactured using solid drawn copper tubes and aluminium fins. Each coil shall be fitted with an air vent. Filters Standard filters shall be of the washable type. They shall have a performance classification of G2 in accordance with EN779 (EU2) and a flame resistance to DIN 53438:Class F1. Connections All are to be to BS 2871 Part 1:1971 and suitable for brazed or compression fittings. Coil connections shall be at 40mm centres to enable easy fitment of standard water control valves. Controls All units shall be fitted with illuminated ON/Off switch, three speed selector switch and include +5v / +10v trimmer switches to aid commissioning and be complete with 24 Volt AC transformer output to drive controllers and actuators. Packaging Units shall be supplied with suitable packaging to prevent damage and dust contamination. Units shall be clearly marked with the model identification and site reference and supplied with installation instructions. Certification Units shall be supplied with a CE label designating that they comply with CE requirements for safety. Insulation Dual function thermal and acoustic insulation shall be used and shall be to Class 0 specification. 2

4 MOUNTING / CONNECTIONS Thank you for choosing the Lennox Quantum Waterside Fan Coil Unit. Please read the following information carefully prior to installation. These instructions should be kept in a safe place for future reference. WANING: ISOLATE FOM THE ELECTICAL SUPPLY BEFOE COMMENCING WOK. These units can be installed virtually as delivered. They are intended for fitting behind a suspended ceiling or a similar ceiling void and have circular spigots for connecting to ducting. Similarly, they can have a fresh air spigot fitted when specified. MOUNTING In all cases, the units are fixed to the mounting face by means of four slots in the end flanges. Down rods, 10mm in diameter, should be used to support units 1. Unistrut should be mounted to the slab (see dimensional data) and four 10mm down rods fixed to the unistrut. 2. The down rods should have two nuts and two washers to lock the unit in position. The unit can then be lifted into location, hooking the slots (in the top panel) over the washers. The nuts must then be securely tightened. 3. Check to ensure the unit is level and adjust if necessary. 4. Check that water runs into the waste from the drain tray, by pouring water into it. NOTE: To allow for Service Clearances it is recommended that a minimum space of 50mm is provided from top of the unit to underside of slab. Sufficient space should be provided to allow for clear and safe access to the control panel. PIPEWOK CONNECTIONS 1. Water flow and return connection Plain pipe connection tails are all to BS 2871, Part 1: 1971 and are suitable for brazed or compression fittings. Connection sizes are mm or 22mm outside diameter on the cooling coil and mm on the heating coil. Actual final connection pipesizes will vary depending on valve configuration where fitted. 2. Condensate Tray Connection An end facing 22mm outside diameter copper condensate drain connection tube to BS 2871, Part 1: 1971 is fitted as standard to the condensate tray on all units. 3. Air Vents and Drains Brass air vent and drain tapping points are fitted as standard to all coils. These are positioned at the top and bottom of the header tubes. DUCT CONNECTIONS 1. Discharge Air Side An integral discharge plenum is fitted as standard complete with 197mm or 247mm outside diameter circular spigots. These are to accept standard diameter flexible ducting. Blanking caps are available to order. 2. Inlet Air Side When specified, units will be fitted with an Air Inlet Plenum, this will have the same number, size and position of circular spigots as on the discharge air side. Blanking caps are available subject to order. 3. Fresh Air Spigot The fresh air spigot is available in a size of 100mm diameter. 4. Condensate pump Condensate pump kits are available as an optional factory fitted option. efer to diagrams indicating electrical wiring details. 5. Electrical heating element LQWFC0 2KW LQWFC190 2KW LQWFC260 2KW LQWFC330 4KW LQWFC440 4KW efer to diagrams indicating electrical wiring details. 3

5 ELECTICAL CONNECTIONS / CONTOLS ELECTICAL CONNECTIONS ISOLATE ELECTICAL SUPPLY BEFOE ATTEMPTING SEVICE WOK. A 230V, 50Hz, single phase supply is required. Wiring must be installed by a qualified electrician and conform to current local and national regulations. 1. Wire mains to unit via a double pole isolating switch, fused to IEE regulation. efer to diagrams indicating electrical wiring details. 2. The electrical connection is via a 2m flying lead with factory fitted connector into socket on control box where an electric heater is NOT fitted. If an electric heater is fitted, to connect mains supply to unit, slacken off the screw holding the control box front cover. Carefully pivot the cover to support it, making sure the wires connecting the cover to the unit are not strained. Connect the mains lead via grommet hole in the side panel to the LIVE, NEUTAL and EATH positions on the 12-way terminal block. eplace cover and tighten screw. 3. If a Condensate Lift Pump is specified, this w i l l b e pre-wired back to the control box, but the pump assembly will be taped to the unit and must be fixed to the end of the drip tray before installing the unit, using the screws supplied. 1. Fan Speed Out of 6 speeds available, SL (Super Low), EL(Extra Low), L(Low), ML(Med/Low), M(Med), and H(High), the fan speed selector switch will be wired for three speeds. Speed adjustment and fine tuning is achieved by following the instructions indicated on the label that is positioned on the underside of the unit, adjacent to the control box. Each model size has its specific settings, examples as detailed on page 5 of this document. An example of adjusting the speed setting is described below:- E.g.: If unit is selected for Medium/Low (ML) speed, then the speed selector switch is set at position II and other positions L and M, as below: Position I = L (Low Speed) Position II = ML(Med/LowSpeed) Position III = M (Medium Speed) If selected speed is EL then this would be Position II with SL and L other positions. If selected speed is H then this would be posiition III with M and ML other positions. 4. The fan motors are of the permanent split capacitor type and have a capacitor fixed to the outside of the motor. All motors have thermal overload protection as standard. Access to the fan tray is via removable panels on the bottom face of the unit. CONTOLS All units are fitted as standard with an ON/OFF switch and a FAN SPEED selector switch for three speeds. When specified, the water control valves will have a controller that will be fitted to the exterior of the control box. These are all fitted into the control box and pre-wired. 4

6 FAN SPEED SETTINGS O O O I I I I II III ON +5v +10v 3 spd FAN SPEED SETTINGS To achieve the design speed use a combination of main tappings on the transformer and switch positions on the outside of the control box. 0 Main tapping Fan speed switches Output Volts W Y Switch +5 V V speed EL I L I ML II M II H III Main tapping Fan speed Output Volts switches W Y Switch +5 V V speed EL I L I ML II M II H III Main tapping Fan speed Output Volts switches W Y Switch +5 V V speed SL I EL I L II ML II M II H III Main tapping Fan speed Output Volts switches W Y Switch +5 V V speed EL I L I ML II M II H II Main tapping Fan speed Output Volts switches W Y +5 Switch V V speed EL I L I ML II M II H II Main tapping Fan speed Output Volts switches W Y Switch +5 V V speed EL I L II ML II M II H III

7 PEIODIC MAINTENANCE PEIODIC MAINTENANCE POCEDUE The following routine maintenance operations should be carried out twice a year or at such shorter intervals as may be dictated by climatic conditions or cleanliness of conditioned space. 1. outine Precautions SWITCH OFF POWE SUPPLY AT THE MAINS OUTLET BEFOE COMMENCING ANY WOK ON THE EQUIPMENT. DO NOT OPEATE FAN FO LONG PEIODS (OVE 2 HOUS) UNDE FEE AI CONDITIONS. I.E WITHOUT DUCTWOK CONNECTED. DO NOT USE STEAM JET O HIGH PESSUE HOT WATE TO CLEAN COIL SUFACES. 2. General Thoroughly clean chassis, baseplate, drain tray. Clean casing. The unit exterior surfaces should be inspected monthly and any signs of corrosion or scratches should be treated immediately. 3. outine Checks Check voltage at supply point with unit running. 4. Condensate Trays Check condensate drains are clean and free running. Check condensate hose connections are secure and leak free. Clean the condensate tray thoroughly. Check and clean condensate pump if fitted. Check operation of tray, drains or pump by introducing water into tray. 6. Fan Motor and Fan A regular check on the fan/motor assembly is advisable to ascertain if any overheating of the motor is occurring and that the fan impeller is free running and has not sustained any damage. Check that fans and fan motor are properly aligned. Check all securing screws, bolts and nuts are tight. 7. Coil The coil should be inspected every six months to ascertain if any foreign matter has accumulated between the fins and that the coil connections are free from leaks. Should the fins become contaminated too frequently, it is advisable to check that the air filter is functioning correctly. Use a soft brush and vacuum cleaner to remove any dust between fins. Comb fins if required. DO NOT UN UNIT WITHOUT FILTE FITTED. 8. Filter egular cleaning of return air filter is essential, every three to six months depending on the working environment of the unit. Dirty filters will reduce the air volume handled by the unit, thus adversely affecting its performance. Clean the filter using a vacuum cleaner O remove the filter from the unit and fully immerse in warm water with a mild detergent. inse in clear water, allow to dry before replacing. 5. Controls Check all connections for burning or wear. eplace if necessary. Ensure all electrical connections are secure. Check functions of controls according to operating procedures. 6

8 FANCOIL MAINTENANCE FANCOIL MAINTENANCE NOT UNNING OK, BUT:- Noisy CHECK IMPELLOS AE SE- CUE AND NOT UBBING ON SCOLLS. ESET MCB CHECK MAINS SUPPLY POO AIFLOW CHECK MOTO SPAES DEPT EPLACE MAX 3 AMP CHECK UNIT FUSE SPAES DEPT CHECK FILTE FO BLOCKAGE EXAMINE FILTE WASH O VACUUM EPLACE IF NEC, SPAES DEPT. 24V AND MAINS OUTPUT CHECK POWE SUPPLY TO FANS SPAES DEPT CHECK TANSFOME CHECK COIL FO BLOCKAGE CLEAN WITH VAC- UUM CLEANE SPAES DEPT ADD LINK BETWEEN TEM 8 & 9. IF FCU WOKS CONTOL- LE IS FAULTY CHECK CONTOLLE FANCOIL WOKING COECTLY SPAES DEPT CHECK MOTO/CAPACITO FANCOIL WOKING COECTLY OK, BUT:- POO COOLING/HEATING PEFOMANCE IF FITTED CHECK THEMOSTAT SETTING EXAMINE SET POINT WATESIDE UNIT AISIDE UNIT SPAES DEPT EXAMINE VALVES & ACTUATOS CHECK DAMPE MECHANISM SPAES DEPT CHECK ACTUATO SPAES DEPT OK EXAMINE WATE FLOW TEMPEATUE CONTINUE NOT WOKING EXAMINE FANCOIL WOKING COECTLY When contacting Spares Dept please specify Unit type, size and ef number. 7

9 DATA ELECTICAL DATA FAN MODEL SPEED Volts H 200 LQWFC M ML 0 L 130 EL 120 H 170 LQWFC M ML 140 L 130 EL 120 H 200 LQWFC M ML 0 L 140 EL 130 H 170 LQWFC M ML 140 L 130 EL 120 H 180 LQWFC M ML 140 L 130 EL 120 H 195 LQWFC M ML 160 L 145 EL 130 Motor Full Load Start Power Current Current W A A COIL WATE CONTENT COIL WATE CONTENT Water No of MODEL Temp. rows Heating NA 1 0/3 Low 3 0/4 Low 4 0/3 High 3 0/4 High 4 Heating NA 1 190/3 Low 3 190/4 Low 4 190/3 High 3 190/4 High 4 Heating NA 1 260/3 Low 3 260/4 Low 4 260/3 High 3 260/4 High 4 Heating NA 1 330/3 Low 3 330/4 Low 4 330/3 High 3 330/4 High 4 Heating NA 1 440/3 Low 3 440/4 Low 4 440/3 High 3 440/4 High 4 Heating NA 1 480/4 High 4 Water content litres WEIGHTS, MINIMUM No. SPIGOTS, COIL CONNECTIONS MODEL WEIGHT MINIMUM No. SPIGOTS kg Total Front LQWFC0 LQWFC190 LQWFC260 LQWFC330 LQWFC440 LQWFC COIL CONNECTIONS (mm) CW LPHW

10 WIING DIAGAM 9

11 FAULT FINDING NEW FANCOIL FAULT FINDING NOT UNNING OK, BUT:- Noisy ENSUE AHU WAS TUNED OFF WHILE SOUND TESTING CHECK IMPELLOS AE TIGHT AND CENTAL ON SHAFT WITHIN SCOLLS ESET MCB CHECK MAINS SUPPLY POO AIFLOW EXAMINE TANSFOME TAPPINGS EPLACE MAX 3 AMP CHECK UNIT FUSE CHECK VOLTAGE TO FANS EXAMINE SCHEDULE CHECK POWE SUPPLY TO FANS CHECK QUOTED AI FLOW CHECK DESIGN STATIC PESSUE CIMP CONNECTIONS, (CONTINUITY TEST WIES) 24V AND MAINS OUTPUT EXAMINE SWITCH & WIING EXAMINE DUC TWOK CHECK ACTUAL STATIC PESSUE IN PLENUM NOT THE DUCTWOK. CHECK QUANTITY & LOCATION OF SPIGOTS EPLACE CHECK TANSFOME EXAMINE METHOD OF MEASUEMENT CALIBATED/COECTION FACTO CHECK SOUCE OF CONTOLLE ADD LINK BE- TWEEN TEM 8 & 9. IF FCU WOKS CONTOLLE IS FAULTY CHECK CONTOLLE CHECK FILTE & COIL FO BLOC KAGE EXAMINE FILTE TYPE! CLEAN O EPLACE IF NEC, IF EU3 FITTED CHECK CO- ECT ALLOWANCE USED CHECK COIL FO BLOCKED FINS IF FEE ISSUE INFOM SUP- PLIE IF NOT EPLACE EPLACE CHECK MOTO/CAPACITO OK, BUT:- CHECK IMPELLO OT ATION MOTOS/IMPELLOS DIECTION OF OTATION POO COOLING/HEATING PEFOMANCE OK CHECK QUOTED PEFO MANCE CONTINUE NOT WOKING IF FITTED CHECK THEMOSTAT SETTING EXAMINE SET POINT & WIING EXAMINE WATESIDE UNIT AISIDE UNIT CHECK SOUCE EXAMINE VALVES & ACTUATOS CHECK DAMPE MECHANISM CHECK SENSO POSITION MAY BE IN DAFT IF FEE ISSUE INFOM SUPPLIE IF NOT EPLACE CHECK ACTUATO SENSO MAY BE TOO CLOSE TO DISCHAGE GILL. EXAMINE WATE FLOW TEMPEATUE FANCOIL WOKING COECTLY 10

12 SPAE PATS LIST Size Used On : Part Number Description E142 Air Vent ( ) X X X X X Z Cooling Coil 3 row (Low Temp. 5-8 deg.c Flow) X Z Cooling Coil 3 row (Low Temp. 5-8 deg.c Flow) X Z Cooling Coil 3 row (Low Temp. 5-8 deg.c Flow) X Z Cooling Coil 3 row (Low Temp. 5-8 deg.c Flow) X Z Cooling Coil 3 row (Low Temp. 5-8 deg.c Flow) X Z Cooling Coil 3 row (High Temp deg.c Flow) X Z Cooling Coil 3 row (High Temp deg.c Flow) X Z Cooling Coil 3 row (High Temp deg.c Flow) X Z Cooling Coil 3 row (High Temp deg.c Flow) X Z Cooling Coil 3 row (High Temp deg.c Flow) X Z Cooling Coil 4 row (Low Temp. 5-8 deg.c Flow) X Z Cooling Coil 4 row (Low Temp. 5-8 deg.c Flow) X Z Cooling Coil 4 row (Low Temp. 5-8 deg.c Flow) X Z Cooling Coil 4 row (Low Temp. 5-8 deg.c Flow) X Z Cooling Coil 4 row (Low Temp. 5-8 deg.c Flow) X Z Cooling Coil 4 row (High Temp deg.c Flow) X Z Cooling Coil 4 row (High Temp deg.c Flow) X Z Cooling Coil 4 row (High Temp deg.c Flow) X Z Cooling Coil 4 row (High Temp deg.c Flow) X Z Cooling Coil 4 row (High Temp deg.c Flow) X Z Fan Tray Assembly X Z Fan Tray Assembly X Z Fan Tray Assembly X SZ Fan Tray Assembly X SZ Fan Tray Assembly X SZ Motor - Single Shaft (240v 50HZ) X X SZ Motor - Twin Shaft (240v 50HZ) X X X X (x2) SZ Impeller - Aluminium. X X (x2) X (x2) X (x3) X (x4) ZZ-S ocker Switch (On / Off) X X X X X ZZ-S ocker Switch - 3 Position (Speed Change) X X X X X Z Transformer (Auto 1.5amp.) X X X X Z Filter Assembly (EU2) X Z Filter Assembly (EU2) X Z Filter Assembly (EU2) X Z Filter Assembly (EU2) X Z Filter Assembly (EU2) X Z Filter Assembly (EU3) X Z Filter Assembly (EU3) X Z Filter Assembly (EU3) X Z Filter Assembly (EU3) X Z Filter Assembly (EU3) X SZ Drip Tray Assembly X SZ Drip Tray Assembly X SZ Drip Tray Assembly X SZ Drip Tray Assembly X SZ Drip Tray Assembly X Z Plenum Dust / Spigot Caps (200 dia.) X X X X X Z Plenum Dust / Spigot Caps (250 dia.) X X X X X Z Condensate Pump Kit X X X X X 12

13