13. The wireless coding and timing arm and disarm settings Function Setting First / second group of time arm set 1.

Transcription

1 Contents 10.4 Arm and disarm the Upload Settings Preface 11. Alarm type set Function Instruction 12. Zone type setting About the host 13. The wireless coding and timing arm and disarm settings Function Setting 13.1 First / second group of time arm set 1. Initialization 13.2 First / second group of time disarm set 2. System Settings Timing arm and disarm switch settings 3. Exit set 13.4 Wireless siren coding settings 4. Password recovers 13.5 Wireless smart appliance control 5. Factory Reset 14. History query 6. Password and system time setting 15. Host state 6.1 Engineering password setting 16. Day-to-day operations 6.2 user password settings 17. Out arm 6.3 system date setting. 18. Home arm 6.4 system time setting 19. Host disarm 7. Voice alarm telephone setting and deleting 20. Answer the alarm 7.1 1~6 group user telephone number setting 21. Remote control 7.2 1~6 group user telephone number deleting 22. SOS 8. Coding or deleting Remote control and detector Maintenance 8.1 Coding to remote control 1. System detection 8.2 Coding of detector 2. Note 8.3 Remote control deleting 3. Technical Parameters Schedule 8.4 Single detector deleting. 8.5 All detectors deleting. Preface 9. System function options settings 9.1 phone line broken alarm setting Thank you for choosing the wireless alarm system product 9.2 Tone of arming or disarming setting 9.3 Siren ring time Wireless alarm system adopts the most advanced digital sensing and controlling 9.4 arm delay time setting technologies, it is the intelligent alarm control system containing burglar alarm, fire 9.5 Delay time of Arm alarm, fire fighting, gas leakage and SOS. 9.6 Phone alarm number of cycles 9.7 Remote number of rings Wireless alarm system uses the most advance multiple random selection 9.8 Keyboard password protection technology, it avoids the problems of interference and alarm missing which exist 9.9 Record setting usually in the similar systems. This system can be used widely in residence, shops, 10. Network alarm settings villa, small enterprise and so on Set the first and second groups of center number 10.2 Delete center number For you safety, before install and use, we suggest you to read this manual 10.3 User ID code set carefully. 1

2 [Function Instruction] [About the host] 1. An advanced and reliable communication technology, dialing alarm The console shall be installed in the centre of the prevent site which could realize best 2. 8 wired, 99 wireless defense zones receiving effect from all wireless detectors. Please note that keep the console away 3. Remote control intelligent code, up to 5 wireless remote controls. from large-sized metallic objects and home appliances producing high-frequency 4. LCD display, built-in calendar clock, operates easily. interference, and avoid steel-reinforced concrete and fire-proof doors. 5. Full voice prompts, installation setting and daily operation are more easily. Alarm Panel Front Schematic Diagram: 6. Built-in intercom speaker, can achieve duplex intercom function 7. Built-in wireless transmitter module, wireless siren and smart home system can be linked 8. Preset 2 groups timing arm and disarm time 9. Calls out up to 6 phone numbers to notify you of abnormal conditions 10. Call out up to 2 phone numbers to notify the receiving alarm center seconds artificially recording message 12. Built-in digital voice, voice broadcast alarm situation automatically 13. All arm and disarm function could be realized by one key 14. Multiple defense zones including instant, delay, 24 hours, bypass 15. Wireless coding: adding new accessories convenient, safe and efficient Alarm Panel Back Schematic Diagram: 16. Remote control: host arm, disarm, monitor, intercom, on / off alarm function alarm events can be recorded 18. Multiple arming modes such as timely arm by remote control, out arm delay by keypad etc. 19. Built-in AAA NI-HM rechargeable battery pack, power off alarm 20. Compatible with internationally accepted protocol Alarm Center: stability treasure Contact ID alarm communication protocol 2

3 [Function Setting] 1. Initialization Telephone, telephone line, wired detectors and external siren connects with the host, and then plugs in DC12V power adapter. At this point, the speaker has a long "beep" sound and the host into the working state after 1 second. Finally, the back-up battery switches to turn [ON] state. 2. System Settings In the setup process, press the [*] key to return to the previous level, pres the [ # ] key to repeat the current menu or to confirm function and operate according to the voice prompts, after entering the settings Enter four digits engineering password [XXXX] under the disarmed or armed state, and then input the [#] key to confirm. The host voice prompts: Please press 1 to set password and time; press 2 to set or delete alarm phone numbers; press 3 to Note: wired defense zone is from 81~88, Z1=81, Z8=88 in turn. program or delete wireless detectors and remote controllers; press 4 to go to the system options setup; press 5 to setup connection with external alarm center; please enter 6 to set alarm type and enter; 7 to set defense zone type; press 8 to set wireless encoding and scheduled Arm/disarm; Press 9 to check the system history log; press 0 for factory reset; press * to exit. Displaying [----], the host enter the setting state. During the setting status, operation of multiple functions can be repeated. If no operation during the voice prompts, hosts will automatically exit the settings and return to the standby state after two voice prompts. Note: engineering factory password is [6666]. Operating: [XXXX] [#] XXXX represents: a four-digit engineering password 3

4 3. Exit set Setting method:[0] [XXXX] After setting, you need to exit the setting state, press the [*] key continuously. XXXX represents:four digit user password Each time you press the [*] key are accompanied by a "beep". Generally Operating:[0] [1234] pressing [*] twice continuously can return to the standby state. 6. Password and system time setting Operating: [*] [*] Enter the settings according to the main menu after the voice prompt, press 1 4. Password recovers to enter the password and system time setting. Then you will hear that: To set If forget the password or unable to operate the host, please recover the administrator password, please press 1; for user password, press 2; for password. date, press 3; for time, press 4; To return to the previous menu press *, To In the arming or disarming status, enter the [ ] on the keyboard, replay please press #. Accord the voice prompt to start different operating. and then enter [#] to confirm. The host has two short beeps. The hosts recover 6.1 Engineering password setting passwords successful and passwords backs to factory value. Enter the password and system time setting, press the [1] on keypad, voice User password:1234;engineering password:6666 prompt: Please input a 4-digit password. After new password were inputting, Operating:[ ] [#] Voice prompt: Setting completed. Fault engineering is: Factory Reset Operating:[1] [1] [XXXX] If the system is unstable, or forgets the previously setting parameters, XXXX represents:4- Digits new engineering password etc., it is recommended that users restore factory value operation, re-set Example: change engineering password to 3928 the host. Operating: [1] [1] [3928] Two ways of factory reset: First: In disarm status, use keypad to enter [ ] and press [#] to confirm, all the Led indications will be on for 2 seconds and you will hear a long beep. The host gets all its settings cleared and restores to its factory 6.2 user password settings settings successfully. After entering the password system time settings, press [2] on keypad, voice Operating method:[ ] [#] prompt: Please input a 4-digit password. A 4- digits new user password is entered, the voice prompts: Setting completed ". User password changed Second: Enter settings, according the voice prompt of the main menu, press 0 successfully. The default user password is: 1234 to restore the state of the system settings. Then you will continue to hear the Operating:[1] [2] [XXXX] following voice: "Please input password. According voice prompt to enter a XXXX represents:4- Digits new user password four-digit user password, all the Led indications will be on for 2 seconds and Example:change user password to 3405; you will hear a long beep. The host gets all its settings cleared and restores to Operating:[1] [2] [3405] its factory settings successfully. 4

5 6.3 system date setting 7. Voice alarm telephone setting and deleting After entering the password and system time settings, you press [3] on keypad After entering the settings, you press 2 to enter the voice alarm call set and please. Voice prompts: "Please input a six-digit system date. A six-digit system delete settings according to the main menu of voice prompts. Then you will date is entered, the voice prompts: Setting completed. System date is continue to hear the following voice: Please press 1 to set the first alarm changed successful. phone number, press 2 to set the second phone number, press 3 to set the Operating: [1] [3] [AA] [BB] [CC] third phone number, press 4 to set the forth phone number, press 5 to set the AA represents: the current year after a two-digit fifth phone number, press 6 to set the sixth phone number; press 7 to set the BB represents: two digits of the current month first SMS alert phone number; press 8 to set the second SMS alert phone CC represents: two digits of the current date number. To return to the previous menu press [*],To replay please press #. Example: the date is set to According voice prompt to please press [1~8], Voice prompt: Set phone Operating: [1] [3] [12] [07] [01] number, please press 1; delete phone number, please press 2. Accord the voice prompt to start different operating. Note: This version of the host does not have to set the SMS number, so the instruction of operation method is not written ~6 group user telephone number setting 6.4 system time setting After voice Alarm phone settings and deleting, please according the voice After entering the password and system time setting, you press [3] on keypad prompt to press [1-6], voice prompts: To set phone number, please press please. Voice prompts: Please input a four-digit system time. A four-digit 1; to delete phone number, please press 2 ". Then press [1] to set the system time is entered, the voice prompts: Setting completed. System time is phone number. Finished entering the phone number, press [#] to confirm. changed successful. The voice prompts: "setting completed". The user's phone number is set Operating:[1] [4] [DD] [EE] successfully. DD represents: the number of hours of the current time (24-hour). Operating:[2] [1~6] [1] [XXXXXXXX] [#] EE represents: the number of minutes of the current time. 1~6 represents:the one set belongs the six telephone numbers. Example: time is set to 7:51 AM XXXXXXXX represents:user s telephone number Operating:[1] [4] [07] [51] Special note: If your phone is connected to the switch, and please add digital 0 or 9, otherwise the phone cannot dial out. Example:Set the first telephone number as Operating:[2] [1] [1] [ ] [#] 5

6 7.2 1~6 group user telephone number deleting 8.2 Coding of detector After voice Alarm phone settings and deleting, please according the voice Wireless detector should be coded with the host, in order to the host could prompt to press [1-6], voice prompts: " To set phone number, please press 1; trigger alarm by it. to delete phone number, please press 2". Then press [2] to delete the phone After enter the coding or deleting remote control and detector setting, accord voice number. Finished entering the phone number, press [#] to confirm. The voice prompt to press [2], voice prompt: Please enter a two-digit defense zone, prompts: Delete completed". The user's phone number is set successfully. between 02 to 99. Accord voice prompt to enter number of defense zones [02~99]. Operating:[2] [1~6] [2] Voice prompt: please trigger detector. When detector was triggered, you will hear: 1~6 represents:the one detected belongs the six telephone coding completed. numbers. Operating:[3] [2] [02~99] Example:Delete the first telephone number 02~99 represents :Defense zones number of 02~99 Operating:[2] [1] [2] Example: coding defense zones of coding or deleting Remote control and detector Operating:[3] [2] [05] After entering the settings, please accord to the main menu of voice prompts to press 3 to enter a remote control / detector setting of the coding and deleting. Then you will continue to hear the following voice: Please press 1 to program remote controllers, press 2 to program wireless detectors, press 3 to delete remote controllers, press 4 to delete one detector, press 5 to delete all detectors. To return 8.3 Remote control deleting to the previous menu press *, To replay please press #. Accord voice prompts to The remote control has been deleted; it cannot be any operation of the press [1~5]. Accord the voice prompt to start different operating. alarm host 8.1 Coding to remote control After enter the coding or deleting remote control and detector setting, accord voice Remote control should be coded with the host, if want to control the host prompt to press [3], voice prompt: delete completed.all remote controls were After enter the coding or deleting remote control and detector setting, accord voice deleted. prompt to press [1], you will hear: Please press any key on the remote controller. Operating:[3] [3] After pressing, voice prompts: Coding completed. If the remote control has been 8.4 Single detector deleting. coded, voice prompts: Encoding repeat, coding failure. The detector has been deleted; it cannot be any operation of the alarm host. Note: If would like to continue to code next remotes, only need to then press any After enter the coding or deleting remote control and detector setting, accord voice key of next remotes, press the [#] to exit the remote control code prompt to press [4] : Please enter a two-digit defense zone, between 02 to 99. Operating:[3] [1] Accord voice prompts to press defense zone number [02~99]. Voice prompt: Deleted completed Single detector was deleted successful. Operating:[3] [4] [02~99] 6

7 02~99 represents :Defense zones number of 02~ Tone of arming or disarming setting Example: coding defense zones of 05 When arming or disarming, the operation will be prompted through external Operating:[3] [4] [05] siren 8.5 All detectors deleting. In system function options setting states, according voice prompt to press [2], you The detector has been deleted; it cannot be any operation of the alarm host. will hear: Press 1 on, press 0 off. Press [1] or [0] according your request, finally After enter the coding or deleting remote control and detector setting, accord voice you will hear that: setting completed. Phone line broken alarm was set prompt to press [5], Voice prompt: Deleted completed All detectors were deleted successful. Factory fault: turn on successful. Setting method:[4] [2] [X] Operating:[3] [5] X=1:Arm/disarm prompt tone is on 9. System function options settings X=0:Arm/disarm prompt tone is off Enter the settings according to the main menu after the voice prompt, and then For example:arm and disarm the tone turned off operation press [4] to enter system function options setting. You will hear: Please press 1 to Operating method:[4] [2] [0] set the alarm for phone line error, press 2 to set siren on or off when arm or disarm, 9.3 Siren ring time press 3 to set siren duration, press 4 to set arm delay, press 5 to set alarm delay, Enter into the system settings, according to voice prompts, press [3] on the press 6 to set the number of cycles to call alarm phone, press 7 to set the number keyboard, voice prompt: Please input two digits, between 00 to 15. Input the of ring times when calling from remote, press 8 to set password for access when delay time [00 to 15] minutes. The last voice prompt: Setting completed ". Siren arm/disarm by keypad, press 9 to enter voice recording; To return to the previous ring time setting successfully. Factory default: 3 minutes. menu press *, To replay please press #. Please press [1~9] and start different Setting method:[4] [3] [XX] operating according the voice prompt. XX: [00~15] minutes 9.1 phone line broken alarm setting For example: Siren rings 2 minutes operation Set phone line broken alarm could protect telephone line. Operating method:[4] [3] [02] In system function options setting states, according voice prompt to press [1], you 9.4 arm delay time setting will hear: Press 1 on, press 0 off. Press 1 or 0 according your request, finally you Arm delay the host will delay a specific time before entering into armed state will hear that: setting completed. Phone line broken alarm was set successful. when the remote armed Factory fault: turn on Enter into the system settings, voice prompts, press [4] on the keyboard, voice Operating:[4] [1] [X] prompts: Please input two digits, between 00 to 99. Input the delay time [00 to 99] X=1 represents :Turn on seconds. The last voice prompt: Setting completed ". Arm delay set successfully. X=0 represents :Turn off The factory default: do not delay. Example:Turn off phone line broken alarm function Setting method: [4] [4] [XX] Operating:[4] [1] [0] XX:[00~99]seconds 7

8 For example:delay time of arm is 10 seconds voice prompts: " Please input one digit, between 0 to 9.Enter the remote number Operating method:[4] [4] [10] of rings [0 ~ 9]. The last voice prompt: Setting completed ". Remote successfully set the number of rings. The factory default: Delay time of Arm Note: If the remote number of rings is set to 0, it will turn off the remote control Arm delay: host will alarm in specific time when it receives the signal function Enter into the system settings, voice prompts, press [5] on the keyboard, voice Setting method: [4] [7] [X] prompts: Please input two digits, between 00 to 99. Input the delay time [00 to 99] X : [0 to 9] times seconds. The last voice prompt: Setting completed ". Alarm delay set successfully. Example: 2 times the number of rings to set up a remote operation. The factory default: do not delay. Operating method: [4] [7] [2] Setting method:[4] [5] [XX] 9.8 Keyboard password protection XX:[00~99] seconds The host keypad lock can guarantee that the host password is not malicious For example: delay time of alarm is 10s changed Operating method:[4] [5] [10] Into the system settings, voice prompts, press [8] key on the keyboard, voice 9.6 Phone alarm number of cycle s times prompts: Press 1 on, press 0 off ". If need turn on the keyboard password Telephone dial - up cycle s times: Time of the host will dial the first group protection function, just press [1] key to turn it on, telephone number start from scratch again when all the numbers to dial out Press [0] to turn it off. The last voice prompt: Setting completed but did not put through. Keyboard password protection feature set successfully. Factory default: open. Enter into the system settings, voice prompts, press [6] on the keyboard, voice Setting method: [4] [8] [X] prompts: Please input two digits, between 00 to 15. Input the cycle s time [00 to X = 1 represents: keyboard password protection feature is turned on 15] seconds. The last voice prompt: Setting completed. The phone alarm X = 0 represents: keyboard password protection is turn it off. cycle s times successfully set. Factory default: 9 Example: turn the keyboard password protection. Setting method:[4] [6] [XX] Operating method: [4] [8] [0] XX:[00~15] times 9.9 Record setting For example: The specific operation of the alarm 2 cycles. Into the system settings, voice prompt, press the [9] key on the keyboard, hear the Operating method:[4] [6] [02] voice prompts: "Please leave a message Recording icon [ ] long bright, 9.7 Remote number of rings 10-second clock countdown begin, recording begin: from the host 30cm, The ringing signal is issued by the switch send a regular pulse signal to the moderate voice recording in standard Mandarin user information; 10 seconds at handset by detecting it to identify whether there is an incoming call, the the end of the end of the "beep" sound recording; same time, the host handset here is the alarm host automatically start recording playback. Into the system options settings, voice prompts, press on the keyboard [7] key, Setting method:[4] [9] 8

9 10. Network alarm settings Setting method: [5] [1~2] [2] Enter into the settings according to the main menu after the voice prompts. Press [1 ~ 2]: to delete the first or second group center number [5] to enter the network alarm settings. Then you will continue to hear the following Example: delete the first group of center number voice: Please press 1 to set the first alarm phone number, press 2 to set the Operating method: [5] [1] [2] second phone number, press 3 to set user ID, press 4 to set the arm/disarm 10.3 User ID code set uploading report. To return to the previous menu press *, To replay please press #. After entering the network alarm settings, voice prompts, press on the keyboard [3] According to the voice prompts, press the button [1-4] key. Follow the voice key, voice prompted: Please enter a four-digit user ID. Then do it. Press the [#] prompts different operation. key to confirm. The voice prompts: Setting completed " 10.1 Set the first and second groups of center number Setting method: [5] [3] [XXXX] The host networking alarm, it is necessary to set up your computer Alarm [XXXX]: four-digit user coding Center phone number to upload data communications Example: user encoding settings for 2245 After entering the network alarm settings, voice prompts, press [1 ~ 2] on the Operating method: [5] [3] [2245} keyboard, voice prompts: " To set phone number, please press 1; to delete phone number, please press 2. Then, press [1] key to set. Finished entering the phone number, press [#] to confirm. The voice prompts: Setting completed Setting method:[5] [1~2] [1] [XXXXXXXX] [#] [1~2]:First set of numbers and second set of numbers XXXXXXXX:Center number 10.4 Arm and disarm the Upload Settings Example: set the first set number of After entering the network alarm settings, voice prompts, press [4] on the keyboard, Setting method:[5] [1] [1] [ ] [#] voice prompts: Press 1 on, press 0 off The voice prompts: " Setting completed LCD Display: after you turn it on to upload or turn it off. Setting method: [5] [4] [X] X = 1: Turn on arm and disarm the Upload Center X = 0: Close to arm and disarm the Upload Center For example: turn it on of arm and disarm the upload center 10.2 Delete center number Operating method: [5] [4] [1] After entering the network alarm settings, voice prompts, and press on [1 ~ 2] the 11. Alarm type set keyboard, voice prompts: " To set phone number, please press 1; to delete phone Enter the settings according to the main menu of voice prompts, press [6] to enter number, please press 2. Then press [2] to delete the central telephone. The voice the alarm set. Then you will continue to hear the following voice: Please input a prompts: Setting completed two-digit defense zone between 02 to 99, followed by a one-digit alarm type: 0 is 9

10 a bypass defense zone, 1 is real-time defense zone, 2 is stay at home defense X=7: door alarm X=8: boundary alarm zone, 3 is 24 hour defense zone. Please press # to confirm, press * to return ". Example: Set 41 zone as SOS alarm Follow the voice prompts different operation. Enter the two-digit defense zone Operating method:[7] [41] [1] number [02 to 99] and an alarm type [0 ~ 3], press [#] key to confirm. LCD display The default alarm: Instant zone Setting method: [6] [02 to 99] [X] [#] 02~99:02~99 defense number X=0:Bypass defense zones X=1:Real-time defense zone X=2:Stay at home defense zone 13. The wireless coding and timing arm and disarm settings X=3:24-hour defense zone According to the main menu of voice prompts enter the settings, press [8] to enter Example: 46 defense zone is instant zone the wireless coding and timing arm and disarm settings. Then you will continue to Operating method:[6] [46] [1] [#] hear the following voice: Please press 1 to set first scheduled arm, press 2 to set second scheduled arm, press 3 to set first scheduled disarm, press 4 to set 12. Defense zone type setting Enter into the settings according to the main menu of voice prompts to enter the zone typesetting, press [7]. Then you will continue to hear the following voice: Please enter the two digit number of defense zone, than input one digit number of defense zone type, 1. SOS 2.fire alarm 3.gas leak 4. Window alarm 5. Balcony alarm 6.Hall alarm 7.Magnetic contact alarm 8.perimeter alarm. Follow the voice prompts different operation Setting method:[7] [02~99] [X] 02~99:Defense zone number of 02~99 X=1: SOS alarm X=2: fire alarm X=3: gas leaks alarm X=4: window alarm X=5: balcony alarm X=6: hall alarm 10 second scheduled disarm, press 5 to enable/disable arm/disarm schedule, press 6 to enter code for the wireless siren, press 7 for wireless home appliance control. To return to the previous menu press *, To replay please press #. Follow the voice prompts different operation 13.1 First / second group of time arm set Time arm and time disarm are Convenient in the required time segment is armed or disarmed. To enter the wireless coding and timing arm and disarm settings, voice prompts, and press [1~2] on the keyboard, voice prompts: Please enter a four-digit fixed time The input time arming time the voice prompts: " Setting completed Setting method: [8] [1~2] [AA] [BB] [1~2]: First / second group of time arm AA: Hour (24hours) BB: Minute Example: set first group arm time is 22:50 Operating method: [8] [1] [22] [50]

11 X=0:Timing arm and disarm turned off Example:Turn on timing arm and disarm Operating method:[8] [5] [1] 13.4 Wireless siren coding settings Enter the wireless coding and timing arm/disarm setting, voice prompts, press 13.2 First / second group of time disarm set [ 6 ] on the keyboard, voice prompts : " Please enter a eight-digit wireless address Time arm and time disarm are Convenient in the required time segment is code. The wireless encoding of eight digits is only from 0-2.The last voice prompt: armed or disarmed. Setting completed. To enter the wireless coding and timing arm and disarm settings, voice prompts, Setting method:[8] [6] [XXXXXXXX] and press [3~4] on the keyboard, voice prompts: Please enter a four-digit fixed XXXXXXXX: eight-digit wireless code time The input time disarming time.the voice prompts: "Setting completed Example:Set wireless encoding as Setting method:[8] [3~4] [AA] [BB] Operating method:[8] [6] [ ] [3~4]:First / second group of time disarm AA: Hour (24hours) BB: Minute Example: set first group arm time is 7:51 Setting method:[8] [3] [07] [51] 13.5 Wireless smart appliance control To enter the wireless coding and timing arm and disarm settings, voice prompts, press [7] on the keyboard, voice prompts: Please enter an eight-digit wireless address code. The wireless encoding of eight digits is only from 0-2.The last voice prompt: Setting completed Timing arm and disarm switch settings Setting method:[8] [7] [XXXXXXXX] Only open timing arm and disarm switch, timing arm and disarm the timing XXXXXXXX:Eight-digit wireless code to be effective Example:Set wireless equipment encoding as Enter the wireless coding and timing cloth disarm setting, voice prompts, Operating method:[8] [7] [ ] keyboard [ 5 ] key, voice prompts : " Press 1 on, press 0 off. After operation it successfully, voice prompts: "Setting completed Setting method:[8] [5] [X] X=1:Timing arm and disarm turned on 11

12 14. History query Remote control operation: Press the remote control [OUT ] key once. Enter the settings according to the main menu after the voice prompt, press [9] to enter Host operation: [OUT ] (keypad lock off) or [OUT ] + user password + # the history query. Then you will continue to hear the following voice: " Press 2 to inquiry (keyboard lock on) next message; Press 8 to inquiry former message; Press * to return previous menu; Press # for replay." Host enters history inquiries, press [2] to downturn, press the [8] to upturn Setting method:[9] 15. Host state Under normal circumstances, usually only the following four states: 1) Arm state: armed, the 02 to 99 zone alarm. 2) Home arm state: armed, the settings for [home arm] are effective zone alarm. 3) Disarm state: disarmed, the 02 to 99 zone alarm (24 hours zone excluded). 4) Set state: when set it, all zones are not the police. 16. Day-to-day operations the remote control is carried out a variety of functional operation of a device by 18. Home arm Home arm (staying): the alarm host is part of the alert arm: someone at home, for safety reasons, you need to be part of the detector in the home (such as doors, windows, balconies, boundary alarm etc.) in a state of alert; another part of the detector (e.g.: hall and other masters of their own trigger to cause false alarm) in non-state of alert, then select home arm. Note: home arm only realize by a remote control to operate. Remote control operation: Press the remote control [ ] key once. Host operation: press home arm [ ] on the keyboard radio, alarm host. The role is to facilitate the users outside the door (households) or distant alarm, operate for out arm, home arm, SOS alarm, and disarm immediately 1) Out arm: Press [ ] key, the host is armed immediately alert. 2) Disarm operation: Press the [ ] key, the host is in disarming standby state immediately. 3) Home Arm: Press [ ] key, is at home (staying) alarm alert. 19. Host disarm 4) SOS alarm: Press [ ] key, the host immediately trigger an emergency alarm Hosts disarm: it is in a non-alert state. One: after arming operation, the normal 17. Out arm disarm; another: after host alarm need stop this alarm, is also disarmed, normal Out arm: the alarm host all alert arming: no one at home, you need to prevent zone will not work after disarm operation, except for 24-hour zones. on-site comprehensive alarm detection alert, all detectors are in working condition; The host keyboard lock is off, you want to disarm, Press disarm buttons directly on triggered when the probe source (thief intrusion, fire, gas leak, etc.)the detectors, the host[ ]can be realized disarm; if the host keyboard lock is turned on, you will alarm system alarm immediately. need to press[ ], then enter user password according to voice prompts, plus [#] If host keyboard lock is off, press the host keyboard [OUT ] key, it will in AWAY key. [Away] or [Home arm] indicator light goes out. Disarm operation is successful. state; if the host keypad lock is on, press the host keyboard [OUT ] key, and then Remote control operation: Press the[ ]] button. need to enter the user password to enter the system external arming state. Host operating: [disarm] (keyboard lock off) or [disarm ] + [user password] + 12

13 [# (keyboard lock on) ] 21. Remote control Via phone (mobile phone) call the phone number connected with alarm host, set the number of rings after the handset to hear "Please input password" tone. In this case, enter the password; password is correct, the earpiece sent prompt Press 1 to arm, press 2 to disarm, press 3 to monitor, press 4 to talk, press 5 to close monitor, press 6 sirens on, press 7 siren off, press 8 to turn on the wireless electrical appliances control, 20. Answer the alarm press 9 to turn off electrical appliances control ;Password error,the earpiece sent Once the alarm host alarm, alarm beep sound immediately; First dial the default prompt Password is incorrect, please re-enter After entering the remote control phone (mobile phone) voice alarm automatically. If the phone unanswered, the operation via the telephone keypad remote control: host will be automatically transferred to the next set of calls, all preset phone Press [1]: the host into the arm state, the earpiece voice prompts: armed. numbers of each cycle dial 9 times. Press [2]: the host into disarm state, earpiece voice prompt: disarmed. " If the dial telephone answers, the handset first heard the alarm zone information Press [3]: the host into the monitor for 30 seconds, if continue monitoring, press [3] and alarm location, and then plays 10 seconds of recording information. Recording key repeatedly delay of 30 seconds. will continue to play after playing remote operation tone: Press 1 to arm, press 2 to Press [4]: start the scene 30 seconds intercom function. disarm, press 3 to monitor, press 4 to talk, press 5 to close monitor, press 6 sirens Press [5]: close monitoring function. on, press 7 siren off, press 8 to turn on the wireless electrical appliances control, Press [6]: turn on the siren. press 9 to turn off electrical appliances control. At the same time, press the keys of Press [7]: turn off the siren the keyboard of the phone (mobile phone), you can achieve different functions: Press [8]: turn on the wireless appliance control. Direct hook: and no one answered the host cycle to dial all phone 9. Press [9]: turn off the wireless appliance control Hang up directly: and no one answered, the host cycle to dial all phone 9 times. 22. SOS Press [1]: the host into the arm state, the earpiece voice prompts: armed. Sometimes, at home occur in some special cases: the elderly or children sudden Press [2]: the host into disarm state, earpiece voice prompt: disarmed. " illness, requiring emergency; suddenly caught fire in the home, they need for help; Press [3]: the host into the monitor for 30 seconds, if continue monitoring, criminals burglary, mugging, must call 110. At this time, simply press the host [ ] press [3] key repeatedly delay of 30 seconds. emergency key, remote control of the [ ] key, wireless emergency button. Alarm Press [4]: start the scene 30 seconds intercom function. system immediately alarm and automatically call for alarm. Press [5]: close monitoring function. Remote control operation: Press the [ ] button. Press [6]: turn on the siren. Host operating: host keyboard [ ] emergency button Press [7]: turn off the siren. Press [8]: turn on the wireless appliance control. Press [9]: turn off the wireless appliance control. 13

14 [Maintenance] 1. System detection 3. Technical Parameters Schedule Alarm system are in use every day, but must also conduct regular maintenance, Table one: periodic testing, in order to ensure the alarm system is stable, reliable, safe operation. Usually, alarm host must be comprehensive detection every three Technical Parameter months, detectors test monthly. Even no conditions you should test them every Input power: DC12V 500mA three months. Standby power consumption : 50mA Host detection: Alarm current: Max 450mA 1 host arm /disarm normally or not. Output current: DC12V 150mA 2. The host alarm whether normal outgoing calls 3.Normal receiver detector signal or battery backup is normal. Radio frequency: 315MHz/433MHz Probe detection: Encoding: 2262 IC / 4.7MΩ 1. Trigger detectors by hand, check whether alarm normally. Alarm sound: 110dB 2 Check the batteries in all detectors, see if under voltage. Back-up battery: AAA 7.2V 3. Test launch of wireless detectors, to see whether it can communicate with the Clock battery: Zn/Ago battery3.0v host. Suitable temperature: -20 ~ Note Suitable humidity: 40% ~ 80% * Do not dismantle, repair and renovation products, otherwise there will be likely to cause accidents and malfunctions. * Do not use this product has been dropped on the ground or a hard object, avoid strong impact, resulting in failure and damage. * Without the relevant permit and consent, do not directly set to the "110", "119" or the police station alarm phone alarm calls of the host. 14

15 Table two: instruction setting Number First-level menu Second-level menu Instruction Remark Factory fault 1 Password and system time setting Engineer password setting 1+1+XXXX XXXX=a 4-digit engineer password setting User password setting 1+2+YYYY YYYY= a 4-digit user password setting system time setting 1+3+AA+BB+ AA=year,BB=month, CC=date CC system time setting 1+4+DD+EE DD=hour,EE=minute 2 Voice alarm telephone setting and deleting 1~6 alarm phone setting 1~6 delete alarm code 2+X+1+YYYY +# 2+X+2 1X=1~6 group telephone number YYYYY=alarm telephone number X=1~6 group telephone number Remote control code 3+1 Remote control Detector code 3+2+XX XX=defense zone number 3 code /Detector code Delete remote control code 3+3 matched and Delete single detector code 3+4+XX XX= defense zone number deleted Delete all detector code 3+5 Phone line broken alarm setting 4+1+X X=1 turn on X=0 turn off 0 Tone of arming or disarming 4+2+X X=1 turn on X=0 turn off 4 setting System function options settings Siren ring time setting 4+3+XX XX=delay time 00~15 minutes 3 minutes arm delay time setting 4+4+XX XX=delay time 00~99 seconds Alarm delay time setting 4+5+XX XX=delay time 00~99 seconds Phone alarm number of cycles 4+6+XX XX=00~15 times 9 times Times of rings 4+7+X X=0~9 times 6 times Keyboard password protection 4+8+X X=1 turn on X=0 turn off Record setting 4+9 Play recoding automatically after 15 recoding

16 Network alarm settings Alarm type set Zone type setting The wireless coding and timing arm and disarm settings Set the first and second groups of center number Delete the first and second groups of center number 5+X+1+YYYYY+# 5+X+2 X=1~2 group 16 X=1~2 group YYYYY=telephone number User ID setting 5+3+XXXX XXXX= 4-digit user password Arm and disarm the Upload 5+4+X X=1 turn on X=0 turn off Settings Alarm type set 6+XX+Y+# 02~99:02~99 defense number, X=0: Bypass defense zones X=1:Real-time defense zone, X=2:Stay at home defense zone, X=3:24-hour defense zone Zone type setting 7+XX+Y 02~99:02~99 zones number X=1: SOS alarm X=2: fire alarm X=3: gas leaks alarm X=4:window alarm X=5:balcony alarm X=6:hall alarm X=7:door alarm X=8:boundary alarm First / second group of time arm set First / second group of time disarm set Timing arm and disarm switch settings 8+X(1~2)+AA+BB 8+X(3~4)+AA+BB 8+5+X X: First / second group of time arm AA: Hour (24hours) BB: Minute X:First / second group of time disarm AA: Hour (24hours) BB: Minute X=1 turn on X=0 turn off Wireless siren coding settings 8+6+XXXXXXXXX XXXXXXXX=8 is wireless coding Wireless smart appliance control 8+7+XXXXXXXXX XXXXXXXX=8 is wireless coding 9 History query History query 9 press [2] to downturn, press the [8] to upturn Instant defense zones