FROM: PARKHILL, SMITH, & COOPER, INC. PROJECT NAME: BORGER XCEL BUILDING AND

Transcription

1 4 85th Street Lubbock, Texas ADDENDUM NO: 01 TO: ALL PLANHOLDERS FROM: PARKHILL, SMITH, & COOPER, INC. PROJECT NAME: BORGER XCEL BUILDING AND PROJECT NO.: DATE: 07//015 07//15 Attention of all Prospective Proposers/Plan Holders is directed to the following modifications to the referenced Drawings and Project Manual. This Addendum becomes a part of the Contract Documents and modifies the original Contract Documents dated July 015 as noted below: This Addendum consists of one page plus SECTION and the attached detail drawing E101. I. CHANGES TO PROJECT MANUAL: A. SECTION HARDWARE 1. Add this section in its entirety as attached to this addendum. II. CHANGES TO DRAWINGS: A. SHEET C10 SITE PLAN 1. For key note #1: the generator pad is shown for location reference only, actual dimensions are 6.5ft x 10ft. Design of the pad shall be in accordance with manufacturer s recommendation. B. SHEET A Demolition of the two pairs of storefront entry doors on the North end of building and single storefront entry door and west side, doors only, frames to remain. C. SHEET A New doors 100, 101 & 10 in existing frames, field verify measurements.. The walls between rooms 106, 107, and 108 have moved so as the dimension of room 106 is 13, room 107 is 13, and room 108 is /8 with 3 5/8 studs between. D. SHEET A New doors 100, 101 & 10 in existing frames, field verify measurements. E. SHEET E See attached revised sheet E101 for updated riser diagram and removal of work from Secretary 115. End of Addendum. \\Data1\Projects\014\ \BIDPROPOSAL PHASE\ADDENDUM NO.01\PSCArch Addenda.docm Abilene Amarillo El Paso Las Cruces Lubbock Midland team-psc.com

2 SECTION HARDWARE PART 1 - GENERAL 1.1 RELATED DOCUMENTS 7//015 A. Drawings, General Conditions of the Contract for Construction, Supplementary Conditions (if any) and Division 1 - General Requirements apply to Work of this Section. 1. SECTION INCLUDES A. All finish hardware necessary for completion of project. 1.3 RELATED SECTIONS A. Section Custom Casework: Casework Hardware. B. Section Steel Doors and Frames C. Section Flush Wood Doors D. Section Aluminum Entrances and Storefronts: Hardware for same except cylinders 1.4 QUALITY ASSURANCE A. Manufacturers Qualifications 1. Companies specializing in manufacturing door hardware with minimum three years experience. B. Regulatory Requirements 1. Fire Door Hardware a. Conform to requirements of NFPA 80 and 101 for doors shown, scheduled, or specified to be in a fire rated wall or to receive a UL-label. b. In case of conflict between hardware specified and NFPA requirements, provide type required by NFPA. c. Provide door hardware listed by UL or Warnock Hersey or other testing laboratory approved by code authority having jurisdiction. d. Provide hardware tested in accordance with NFPA REFERENCES A. National Electrical Manufacturer's Association (NEMA LB3-1995) - Performance Standards for High Pressure Decorative Laminate. B. American National Standards Institute (ANSI) 1. ANSI A117 Building and Facilities - Providing Accessibility and Usability for Physically Handicapped People.. ANSI A156.1 Butts and Hinges. 3. ANSI A156. Bored and Preassembled Locks and Latches. 4. ANSI A156.3 Exit Devices. 5. ANSI A156.4 Door Controls - Closers. 6. ANSI A156.5 Auxiliary Locks & Associated Products. 7. ANSI A156.6 Architectural Door Trim HARDWARE

3 8. ANSI A156.7 Template Hinge Dimensions. 9. ANSI A156.8 Door Controls - Overhead Holders. 10. ANSI A156.1 Interconnected Locks & Latches. 11. ANSI A Mortise Locks & Latches. 1. ANSI A Closer Holder Release Devices. 13. ANSI A Auxiliary Hardware. 14. ANSI A Self-Closing Hinges and Pivots. 15. ANSI A Materials and Finishes. 16. ANSI A156.1 Thresholds 17. ANSI A156. Door Gasketing Systems 18. ANSI A156.3 Electromagnetic Locks 19. ANSI A156.4 Delayed Egress Locks 0. ANSI A156.6 Continuous Hinges 1. ANSI A Auxiliary Locks C. American Society for Testing & Materials (ASTM) 1. ASTM F883 Padlocks. D. Builders Hardware Manufacturers Association (BHMA) 1. BHMA Directory of Certified Locks & Latches.. BHMA Directory of Certified Door Closers. 3. BHMA Directory of Certified Exit Devices. 4. BHMA Directory of Certified Electromagnetic and Delayed Egress Locks E. Code of Federal Regulations (CFR) 1. 36CFR Part Americans With Disabilities Act (ADA) F. Door and Hardware Institute (DHI) 1. DHI-0 Installation Guide for Doors and Hardware.. DHI-03 Keying Systems and Nomenclature. 3. DHI-04 Recommended Locations for Builders' Hardware for Custom Steel Door and Frames. 4. DHI-05 Recommended Locations for Builders' Hardware for Standard Steel Doors and Frames. 5. DHI A115 Wood Door Preparation Standards G. National Fire Protection Association (NFPA) 1. NFPA 80 Fire Doors and Windows.. NFPA 101 Code for Safety to Life from Fire in Buildings and Structures. 3. NFPA 105 Installation of Smoke and Draft Control Door Assemblies. H. Steel Door Institute (SDI) 1. SDI-107 Hardware on Steel Doors (Reinforcement and Application). I. Underwriter s Laboratories, Inc. (UL) 1. Building Materials Directory. 1.6 SUBMITTALS A. Product Data 1. Provide product data on specified hardware.. Submit manufacturer's parts lists, templates, and installation instructions. 3. Provide wiring diagrams, electrical characteristics, and product data on all electrically controlled devices. B. Hardware Schedule 1. Include for each item: Quantities; manufacturer's name and catalog numbers; sizes; detail information or catalog cuts; finishes; door and frame size and materials; location HARDWARE

4 and hardware set identification using same opening numbers as indicated on the drawings; lock trim material thicknesses; lock trim material evaluation test results; corresponding ANSI/ BHMA standard type number or function number from manufacturer's catalog if not covered by ANSI/ BHMA; and list of abbreviations.. Indicate locations and mounting heights of each type of hardware. 3. Indicate lock side of single cylinder doors. 4. Include master cross-reference list indicating door numbers in numerical sequence and associated hardware set. a. If, for any reason, any door is moved from the hardware set indicated in the schedule at the end of this section, provide a master cross-reference list, in numerical sequence, indicating door number, original hardware set and new hardware set for every opening. C. Keying Schedule 1. Hold a keying conference with the Owner or Owner's representative to develop a keying schedule.. Develop schedule in accordance with DHI Obtain keying system approval before delivering hardware to project. 4. Unless otherwise indicated or requested, provide keying as follows: a. Key all doors different and key all doors to the same room alike. b. Key all exterior doors alike. c. Master key all doors except mechanical room doors to one key. d. Key mechanical room doors to existing utilities master key system. D. Certificates of Compliance 1. Submit certificates of compliance attesting that hardware items conform to the NFPA, CFR and ANSI/ BHMA standards specified.. Fire Rated Doors: Submit certificates of compliance, attesting that doors which are indicated, scheduled, or specified to be fire rated are fitted with the required hardware (i.e. active latch bolts, self-closing devices) and operate in accordance with the requirements of NFPA 80 and 101. Identify all such doors on certificates. E. Closeout Submittals 1. Submit in accordance with Section Provide list of actual locations of installed cylinders and their master key code. 3. Submit data on operating hardware, lubrication requirements adjustment methods and inspection procedures related to preventative maintenance. 4. Furnish spare parts data, including a complete list of parts and supplies and source of supply, for locksets, exit devices, closers, electronic locking devices and electromagnetic closer holder release devices. 5. Submit special tools required for hardware adjustment or control. 6. Maintenance Instructions: Furnish 6 complete copies of maintenance instructions listing routine maintenance procedures, possible breakdowns and repairs, and trouble shooting guides. 1.7 DELIVERY, AGE AND HANDLING A. Deliver, store and handle hardware to site in accordance with provisions of Section B. Individually package each article of hardware in manufacturer's standard commercial carton or container, and properly mark or label to be readily identifiable with approved hardware schedule. C. Tag or otherwise identify each change key with door for which its cylinder is intended HARDWARE

5 1.8 COORDINATION A. Coordinate requirements for hardware to be mounted on metal doors or metal frames between hardware manufacturer and door or frame manufacturer to establish location, reinforcement required, size of holes, and similar details. 1.9 WARRANTY A. Provide twenty-five year warranty for door closers EXTRA MATERIAL A. Blank keys: Provide 50 total. B. Provide extra cylinder cores as scheduled. PART - PRODUCTS.1 ACCEPTABLE MANUFACTURERS A. Hinges 1. Bommer Industries; Landrum, SC. Hager Companies; St. Louis, MO 3. McKinney Products Company; Scranton, PA 4. Stanley Hardware Division, Stanley Works; New Britain, CT B. Lock and Latches 1. Sargent Division, ESSEX Industries, Inc.; New Haven, CT C. Push/Pulls 1. Elmes Door Hardware, Teramura International Corporation; Torrance, CA.. Hager Companies; St. Louis, MO 3. Rockwood Manufacturing Co.; Rockwood, PA 4. Triangle Brass Manufacturing Co.; Los Angeles, CA D. Access Control Locks 1. Alarm Lock; Amityville, NY E. Exit Devices 1. Sargent Division ESSEX Industries Inc.; New Haven, CT F. Closers 1. Sargent Division ESSEX Industries Inc.; New Haven, CT G. Overhead Holders 1. Glynn-Johnson; Indianapolis, IN. Rixson Architectural Hardware; Charlotte, NC H. Manual and Automatic Bolts 1. Door Controls International (DCI); Dexter, MI. Glynn-Johnson; Indianapolis, IN 3. H.B. Ives, Harrow Co; Wallingford, CT 4. Triangle Brass Manufacturing Co.; Los Angeles, CA I. Gasketing/Threshholds 1. Hager Companies; St. Louis, MO. Pemko Manufacturing Co.; Memphis, TN 3. Reese Enterprises, Inc.; Rosemount, MO 4. Zero International, Inc.; Bronx, NY HARDWARE

6 J. Protection Plates and Door Edgings 1. InPro Corporation; Muskego, WI K. Door Stops/Bumpers 1. Elmes Door Hardware, Teramura International Corporation; Torrance, CA.. Glynn -Johnson; Indianapolis, IN 3. Hager Companies; St. Louis, MO 4. H.B. Ives, Harrow Co.; Wallingford, CT 5. Triangle Brass Manufacturing Co.; Los Angeles, CA L. Door Silencers 1. Glynn-Johnson; Indianapolis, IN. H.B. Ives, Harrow Co.; Wallingford, CT 3. Triangle Brass Manufacturing Co.; Los Angeles, CA M. Substitutions: Under provisions of Section COMPONENTS A. General 1. Provide hardware components as indicated in paragraph HARDWARE SCHEDULE at the end of this section.. Regardless of whether or not the HARDWARE SCHEDULE at the end of this section has every door and every component scheduled for each opening, provide all components required to make every opening functional based on hardware scheduled for similar openings and the referenced codes. B. Locksets 1. Match existing lock cylinders, locksets, as manufactured by Sargent & Company.. Furnish locksets compatible with specified cylinders. 3. Furnish standard strikes with extended lips to protect trim from being marred by latch bolt. Match cutouts provided in metal frames. a. Mortise Locksets: ANSI A156.13, Series 1000, Grade 1 unless otherwise indicated. b. Bored (Cylindrical) Locksets 1) ANSI A156., Series 4000, Grade 1 unless otherwise indicated. ) Typical -3/4 inch backset. c. Preassembled (Unit) Locksets: ANSI A156.1, Series 000, Grade 1 unless otherwise indicated. d. Interconnected Locksets: ANSI A156.1, Series 5000, Grade 1 unless otherwise indicated. e. Auxiliary Locksets: ANSI A156.36, Grade 1, bored dead locks, unless otherwise indicated. C. Latch Sets: 1. Match existing latchsets locksets, as manufactured by Sargent & Company.. Typical -3/4 inch backset. 3. Furnish standard strikes with extended lips to protect trim from being marred by latch bolt Match cutouts provided in metal frames. a. Mortise Latch Sets: ANSI A156.13, Series 1000, Grade 1 unless otherwise indicated. b. Bored (Cylindrical) Latch Sets: ANSI A156., Series 4000, Grade 1 unless otherwise indicated. D. Exit Devices and Exit Device Accessories 1. Provide dust proof floor strikes for vertical rod devices HARDWARE

7 . Door Lite Coordination: a. Mount centerline of exit devices on doors containing door lites approximately at 38-1/. b. Coordinate with door manufacturer. Lower the centerline of the exit device if needed to locate the exit device below the door lite frame. c. With approval from the Architect, provide manufacturer s standard filler to extend exit device beyond door lite frames where door lites extend below exit device. Factory cut or form filler to match profile of exit device trim. E. Access Control Locks: 1. Access Control Locks to be Trilogy Networx series as manufactured by Alarm Lock of Amityville, NY. F. Locks shall conform to ANSI A156 Grade 1 G. Provide configuration of lock as required by hardware group: 1. Cylindrical lock type a. Proximity/keypad Model Series PDL6100 H. Programming: 1. All programming, including user credentials, scheduling and audit trail retrieval, shall be performed using Alarm Lock DL-Windows software version 4.1.9x or higher.. Communication of all programming from computer containing software to locks shall be through Alarm Lock Gateway model appropriate for building s network system. a. Gateway: 1) Ethernet connected gateway Model Series AL-IME ) Power over Ethernet connected gateway, plenum rated Model Series AL-IMEPOEP 3) Wi-FI connected gateway Model Series AL-IM8011 I. Lock features: 1. Locks, except keypad switch type, to be battery powered by 4 each C size batteries providing 5 year life under normal operating conditions.. Locks to support up to 5000 users with 3-6 digit numeric PIN code, or HID format proximity credential, or both for dual credential requirement. 3. Locks to support up to 500 event schedules. 4. Locks to support in non-volatile memory 35,000 event audit trail. 5. Locks to be weatherproof for indoor or outdoor use in operating temperature range of -31 to +151 degrees Fahrenheit. 6. Locks shall continue to operate as last instructed including maintaining schedules and audit trail, independent of building network system failure. 7. Locks shall be capable of providing a system-wide global emergency lockdown/unlock within 10 seconds when initiated by authorized user from any lock, or from the DL-Windows software. 8. Locks shall adjust schedules automatically to correspond with daylight savings time. 9. Locks shall have remote release capability through hard-wired connection. 10. Locks shall have a single pole, double throw relay output to provide external functions through hard-wired connection. J. Gateway Features: 1. Each gateway shall support up to 63 locks.. Each gateway to communicate to software through the building s network system. a. Ethernet connected gateway 1) Interface: Ethernet 10Base-T or 100Base-TX ) Protocols: TCP/IP, UDP/IP, DHCP HARDWARE

8 b. Wi-Fi connected gateway 1) Wireless standards: IEEE 80.11b; 80.11g ) Frequency range: GHz 3) Output power: 14 dbm dbm/-1.0 dbm 4) Maximum receive level: -10dBm (with PER <8%) 5) Data rates with automatic fallback: 54Mbps 1Mbps 6) Range: up to 38 feet indoors 7) Modulation techniques: OFDM, DSSS, CCK, DQPSK, DBPSK, 64 QAM, 16 QAM 8) Interface: 80.11b, 80.11g, and 10/100 Ethernet 9) Protocols: TCP/IP, UDP/IP, DHCP c. c. Security: IEEE PSK with 18-bit AES Rijndael Encryption 3. Each gateway to communicate to locks through 900 MHz GFSK proprietary 18-bit encryption. a. 50 channels b. 10mW power output 4. Environment: a. Indoor installation b. Operating temperature: -4 to +140 degrees Fahrenheit K. Software: 1. Software to be Alarm Lock DL-Windows supporting 000 locks per system account with a maximum of 50 gateways per system account. L. Security Mode: 1. Security is the essence of this section. Unless otherwise required by code, wireless operated hardware shall remain secured in the event of power failure. Normal operation will require battery power to operate the Networx locks. Emergency mechanical key override shall be provided in the event of battery failure (except for keypad only unit). The Networx lock will function mechanically with its corresponding hardware and will in no way affect the egress at any door. M. Registration of Codes and Credentials/Security Management: 1. All codes and /or credentials for Networx locks shall be recorded by the DL-Windows software-based program specific to the building site.. Every code and/or credential issued by the owner shall be entirely unique to that user to whom it is issued. Cards and fobs identified and protected by type and facility code. 3. Wireless networked door access control system will allow for remote door programming and audit trail retrieval and providing all standalone lock functionality plus network-wide global emergency lockdown/unlock commands. Communication is a secure 18bit AES PC encryption and proprietary RF-link lock-to-gateway encryption. 4. System to provide for audit trail of 40,000 events/lock and up to 500 lock/unlock schedules with time zone support. 5. System to be managed from a single computer utilizing the DL-Windows software 4.1.9X version or higher. 6. Provide construction codes to the contractor during the building s construction period. 7. Construction codes shall self-disable at a specified time and date and shall not require any physical modification of the lock or cylinder. 8. In the event the construction period is longer or shorter than originally planned, locks shall be re-programmable to conform to the schedule change. 9. Wireless locks to be fully keypad programmable HARDWARE

9 N. Closers 1. Closers for outswinging exterior doors: Size one size larger than manufacturer's published recommendations, but not less than size 5.. Size requirements for other closers: Conform to manufacturer's published recommendations, except as specified otherwise. 3. Operating Pressure: Provide closers with maximum operating pressure as follows: a. Interior Doors: Set closing force on doors accessible to the physically handicapped for a push-pull of 5 pounds applied at knob or handle. b. Exterior Doors: Maximum 8.5 pounds. c. Fire Rated Doors: Set to minimum required to relatch door. O. Protection Plates 1. Conformance: ANSI A156.6, category J100.. Fabrication 3. Size a. Width: inches less in width than door width for single doors and 1 inch less for pairs of doors. b. Height 1) Armor Plates: 36 inches. ) Kick Plates: 10 inches except where bottom rail is less than 10 inches, extend plate extend to within 1/-inch of panel mold or glass bead. 3) Mop Plates: 4 inches. P. Door Edge Guards 1. Conformance: ANSI A156.6, category J00, non-mortise type.. Fabrication a. Fabricate from inch thick vinyl, factory adhesive backed with peel off protective paper. Q. Miscellaneous 1. Metal Thresholds a. Conformance: ANSI A b. Style: shall be as indicated on drawings. c. Where required, modify thresholds to receive projecting bolts of flush bolts and exit devices. d. Thresholds for doors accessible to handicapped: Raised thresholds, corrugated, beveled with slopes not exceeding 1:, and with height not exceeding 1/-inch. Bevel not required where height is less than 1/-inch. R. Accessories 1. Special Tools: Provide special tools such as spanner and socket wrenches and dogging keys, required to adjust hardware items. S. Fastenings 1. Provide proper type, size, quantity, and finish with each article of hardware.. Concrete or Grout Filled Masonry: Provide machine screws and expansion shields. 3. Hollow Masonry: Provide resin filled screen anchors equal to Hilti C7 anchors. 4. Gypsum Wallboard: Provide nylon or derlin expansion anchors equal to Hilti Togglers. 5. Fastenings exposed to weather and in finished work: brass, bronze, or stainless steel. 6. Provide one-way or tamperproof screws on exterior doors equipped with half or full surface hinges. T. Fire Door Hardware 1. Conform to requirements of NFPA 80 and NFPA HARDWARE

10 U. Finishes 1. Painting of primed surfaces: Specified in Section Painting.. Plated or Exposed Metal: As indicated in HARDWARE SCHEDULE at end of this Section. V. Keying 1. Key to the existing Sargent & Company factory keyed system.. Key locks in sets or subsets. 3. Furnish locks with the manufacturer's standard construction key system. 4. Send keys directly from lock manufacturer to Owner by registered mail or other approved means. 5. Supply keys in following quantities: a. keys for each lock b. 6 master keys c. 3 grand master keys d. 3 great grand master keys e. 6 construction keys f. 4 control keys. 6. Furnish keys to Owner arranged in a container for key control system storage in sets or subsets as scheduled. PART 3 - EXECUTION 3.1 INSPECTION A. Verify that doors and frames are ready to receive work and dimensions are as indicated on shop drawings. B. Verify that power supply is available to power operated devices. C. Beginning of installation means acceptance of existing conditions. 3. INSTALLATION A. General 1. Locate in accordance with DHI 04 and DHI 05 recommended Locations for Builders' Hardware for Standard Steel Doors and Frames and DHI Recommended Locations for Builders' Hardware for Custom Steel Doors and Frames.. Install in accordance with DHI Coordinate mounting height of exit devices with door lites. 4. When approved, slight variations in locations or dimensions will be permitted. 5. Attach door control devices for exterior doors such as closers and holders to doors with thru bolts such as sex bolts and nuts. 6. Conform to 36CFR Part 1191 ANSI A117.1 for positioning requirements for handicapped. B. Locks and Latches 1. Adjust for latching without binding. C. Door-Closing Device 1. Install and adjust in accordance with templates and printed instructions supplied by manufacturer.. Install on solid doors with thru bolts and grommet nuts HARDWARE

11 3. Insofar as practicable, mount closers as follows: a. Exterior Doors: Mount closer on interior side of all exterior doors. Provide parallel arms or top jam mount closers. b. Interior Doors 1) Mount on room side of door for doors opening to or from halls and corridors. ) Where a door, in the open position, is too close to a wall to prevent the door from opening 90 degrees, or if the closer would hit the wall before contacting the door stop, provide a parallel arm closer. D. Key Control Storage System 1. Install where directed by Architect. E. Armor, Kick and Mop Plates 1. Armor Plates: Where scheduled, install on push side of single-acting doors and on both sides of double-acting doors.. Kick Plates: Where scheduled, install on push side of single-acting doors and on both sides of double-acting doors. F. Door Edgings 1. Install on stop face of butt edge of door unless otherwise scheduled. G. Auxiliary Hardware 1. Install lever extension flush bolts at top and bottom of inactive leaf of pairs of doors.. Install dust-proof floor strike or threshold, cut-out for bottom bolt H. Thresholds 1. Install in a bed of sealant with stainless steel screws and expansion shields.. Provide proper clearance and an effective seal with specified weather stripping. 3. Minimum screw size: #10, length dependent on job conditions. I. Weatherseals 1. Locate as indicated, snug to door face and fastened in place with color matched metal screws after door and frames have been finish painted.. Install to exclude light and air flow when door is in closed position. 3. Screw spacing: as recommended by manufacturer. J. Gasketing 1. Install at inside edge of hinge, head and latch side of door frame. K. Hardware for Labeled Fire Doors 1. Install in accordance with requirements of NFPA 80 AND NFPA HARDWARE SCHEDULE Access Control Accessories 1 EA Networx Gateway AL-IMEPOEP Alarm Lock 1 EA Netwx Software Windows based v4.0.1 or higher with single Alarm Lock database 1 EA Netwx Proxcards AL-HID per box Alarm Lock 1 EA Netwx Training jobsite visit training of owner representative Alarm Lock HARDWARE

12 Keying Requirements Key system: existing Sargent Factory Key System Sargent EA VKC GMK/MK Keyset + Do Not Duplicate Sargent EA VKC Change Keys Bitting + Do Not Duplicate Sargent 1 EA Bitting list: shall include present changes Sargent EA Change keys: per lock or exit device Sargent 6 EA Masterkeys: MK-?? Sargent 4 EA Control keys: CTRL KEY Sargent 50 EA Keyblanks: keyway on order Sargent 6 EA I/C Core LFIC Sargent 1 EA Key Cabinet {two tag 60 capacity} MMF Industries Hardware Set / Door Number: 100 NOTE: supplier shall carefully trim existing pivots to cover pivot preps in frame, then install leaf of continuous hinge to then cover the jamb preps EA Cont Hinge DHS83HD1 TEK Duranod Pemko verify with door supplier 1 EA Elec Keyed Mull 90KR-E 84" USP Detex Corp elect for future access ctrl 1 EA Removable Mull powder coat - bronze to match sample EA Rim Exit Device F ETL B Sargent 1 EA Rim Cylinder B Sargent EA Drop Plate 1431-D EB Sargent SET Closer accessry 581- blade stop spacer kit EB Sargent EA Closer/Pa/Stop TB 1431 CPS EB Sargent 1 EA Threshold H/C 005AVK 7" Pemkote Pemko provide 7/16" door undercut EA Door Btm Sweep 345DV 36" Duranod Pemko HARDWARE

13 Hardware Set / Door Number: 101 NOTE: supplier shall carefully trim existing pivots to cover pivot preps in frame, then install leaf of continuous hinge to then cover the jamb preps EA Cont Hinge DHS83HD1 TEK Duranod Pemko verify with door supplier 1 EA Elec Keyed Mull 90KR-E 84" USP Detex Corp elect for future access ctrl 1 EA Removable Mull powder coat - bronze to match sample ********** EA Rim Exit Device B Sargent EA Rim Cylinder B Sargent EA I/C Core LFIC Sargent 1 EA Trilogy Networx ETPDNR1 ETRIC NS8 10B Alarm Lock RHR door EA Drop Plate 1431-D EB Sargent SET Closer accessory 581- blade stop spacer kit EB Sargent EA Closer/Pa/Stop TB 1431 CPS EB Sargent Hardware Set / Door Number: 10 3 EA Hinges BB x 4.5 6D PBB Inc 1 EA Passage 8 11U15 LL 6D Sargent 1 EA Wall Stop 409 3D Rockwood 3 EA Silencers 608 metal frames Gray Rockwood Hardware Set / Door Number: EA Hinges BB x 4.5 6D PBB Inc 1 EA Classroom Lock G37 LL 6D Sargent 1 EA I/C Core LFIC Sargent 1 EA Wall Stop 409 3D Rockwood 3 EA Silencers 608 metal frames Gray Rockwood Hardware Set / Door Number: EA Hvy Wt Hinges 4B x 4.5 6D PBB Inc 1 EA I/C Core LFIC Sargent 1 EA Trilogy Networx PDL6100.ICR 6D Alarm Lock 1 EA Closer/Parallel TB 1431 P10 EN Sargent 1 EA Kickplate 8"h x 34"w x.040 vinyl color? IPC 1 EA Wall Stop 409 3D Rockwood 3 EA Silencers 608 metal frames Gray Rockwood HARDWARE

14 Hardware Set / Door Number: EA Cont Hinge DFM83HD1 TEK Duranod Pemko verify with door supplier 1 EA Rim Exit Device B Sargent 1 EA Rim Cylinder B Sargent 1 EA I/C Core LFIC Sargent 1 EA Trilogy Networx ETPDNR1...ETRIC...NS8 10B Alarm Lock 1 EA Drop Plate 1431-D EB Sargent 1 SET Closer accessory 581- blade stop spacer kit EB Sargent 1 EA Closer/Pa/Stop TB 1431 CPS EB Sargent 1 EA Threshold H/C 005AVK..36" Pemkote Pemko provide 7/16" door undercut 1 EA Door Btm Sweep 345DV 36" Duranod Pemko Hardware Set / Door Number: 105A Hardware Set / Door Number: 106 Hardware Set / Door Number: EA Hinges BB x 4.5 6D PBB Inc 1 EA Classroom Lock G37 LL 6D Sargent 1 EA I/C Core LFIC Sargent 1 EA Wall Stop 409 3D Rockwood 3 EA Silencers 608 metal frames Gray Rockwood Hardware Set / Door Number: 108 Hardware Set / Door Number: EA Hinges BB x 4.5 6D PBB Inc 1 EA Classroom Lock G37.LL 6D Sargent 1 EA I/C Core LFIC Sargent 1 EA Wall Stop 409 3D Rockwood 3 EA Silencers 608 metal frames Gray Rockwood HARDWARE

15 Hardware Set / Door Number: 109A 3 EA Hinges BB x 4.5 6D PBB Inc 1 EA Passage U15...LL 6D Sargent 1 EA Wall Stop 409 3D Rockwood 3 EA Silencers metal frames Gray Rockwood Hardware Set / Door Number: EA Hvy Wt Hinges 4B x 4.5 6D PBB Inc 1 EA I/C Core LFIC Sargent 1 EA Trilogy Networx PDL6100.ICR 6D Alarm Lock 1 EA Closer/Parallel TB 1431 P10 EN Sargent 1 EA Kickplate 8"h x 34"w x.040 vinyl color? IPC 1 EA Wall Stop 409 3D Rockwood 3 EA Silencers 608 metal frames Gray Rockwood Hardware Set / Door Number: EA Hvy Wt Hinges 4B x 4.5 6D PBB Inc 1 EA I/C Core LFIC Sargent 1 EA Trilogy Networx PDL6100.ICR 6D Alarm Lock 1 EA Closer/Standard TB 1431-DA RO EN Sargent adjust delayed closing 1 EA Kickplate 8"h x 34"w x.040 vinyl color? IPC 1 EA Wall Stop 409 3D Rockwood 3 EA Silencers 608 metal frames Gray Rockwood Hardware Set / Door Number: 111A Hardware Set / Door Number: 111B Hardware Set / Door Number: 111C HARDWARE

16 Hardware Set / Door Number: 111D Hardware Set / Door Number: 11 Hardware Set / Door Number: 113 Hardware Set / Door Number: 114 Hardware Set / Door Number: 116 Hardware Set / Door Number: EA Cont Hinge DFM83HD1 TEK Duranod Pemko verify with door supplier 1 EA I/C Core LFIC Sargent 1 EA Trilogy Networx PDL6100.ICR 10B Alarm Lock 1 EA Closer/Standard TB 1431 RO EB Sargent 1 EA Wall Stop B Rockwood Hardware Set / Door Number: 117A 1 EA Rim Cylinder B Sargent 1 EA I/C Core LFIC Sargent 1 EA Trilogy Networx ETPDNR1 ETRIC OS8 10B Alarm Lock HARDWARE

17 Hardware Set / Door Number: 117B 1 EA Cont Hinge DFM83HD1..TEK Duranod Pemko verify with door supplier 1 EA I/C Core LFIC Sargent 1 EA Trilogy Networx PDL6100.ICR 10B Alarm Lock 1 EA Closer/Standard TB 1431 RO EB Sargent 1 EA Wall Stop B Rockwood Hardware Set / Door Number: EA Hvy Wt Hinges 4B x PBB Inc 1 EA Asylum Lock G17.LL 6D Sargent EA I/C Core LFIC Sargent 1 EA Wall Stop 409 3D Rockwood 1 EA Gasketing S88D17 Dk Brz Pemko Hardware Set / Door Number: 118A 3 EA Hvy Wt Hinges 4B x 4.5 6D PBB Inc 1 EA Asylum Lock G17 LL 6D Sargent EA I/C Core LFIC Sargent 1 EA Wall Stop 409 3D Rockwood 1 EA Gasketing S88D17 Dk Brz Pemko Hardware Set / Door Number: 10 1 EA Cont Hinge DFM83HD1 TEK Duranod Pemko verify with door supplier 1 EA Rim Exit Device B Sargent 1 EA Rim Cylinder B Sargent 1 EA I/C Core LFIC Sargent 1 EA Trilogy Networx ETPDNR1.ETRIC NS8 10B Alarm Lock 1 EA Drop Plate 1431-D EB Sargent 1 SET Closer accessry 581- blade stop spacer kit EB Sargent 1 EA Closer/Pa/Stop TB 1431 CPS EB Sargent 1 EA Threshold H/C 005AVK..36" Pemkote Pemko provide 7/16" door undercut 1 EA Door Btm Sweep 345DV 36" Duranod Pemko HARDWARE

18 Hardware Set / Door Number: 11 Hardware Set / Door Number: 1 Hardware Set / Door Number: 13 Hardware Set / Door Number: 14 Hardware Set / Door Number: 15 Hardware Set / Door Number: 16 Hardware Set / Door Number: 17 Hardware Set / Door Number: 17A Hardware Set / Door Number: 17B 1 EA Rim Cylinder B Sargent 1 EA I/C Core LFIC Sargent 1 EA Trilogy Networx ETPDNR1...ETRIC...OS8 10B Alarm Lock HARDWARE

19 Hardware Set / Door Number: 18 Hardware Set / Door Number: 130 NOTE: reuse existing frame, remove existing door & hardware Hardware Set / Door Number: 131 NOTE: reuse existing frame, remove existing door & hardware END OF SECTION HARDWARE

20 GENERAL NOTES 4 KEY NOTES MECHANICAL EQUIPMENT ELECTRICAL SCHEDULE MARK VOLTAGE PHASE PANEL CIRCUIT BREAKER CONDUCTOR CONDUIT DISCONNECT FUSE NOTE EF-1 10 V 1 EXISTING PANEL D 0A/1P ()#1 AWG + #1 GND 3/4" IDU-1 0 V 3/4" 1 ODU-1 40 V 1 EXISTING PANEL D 1,3 0A/P ()#1 AWG + #1 GND 3/4" 30A/P 0A 1 A. ALL DOWNSTREAM DEVICES NOT BEING REMOVED AS PART OF THIS PROJECT SHALL REMAIN ACTIVE. THIS INCLUDES BUT IS NOT LIMITED TO RECEPTACLES, LIGHTS, DATA, FIRE ALARM, SECURITY AND TELEPHONE. B. REFER TO MECHANICAL AND PLUMBING DRAWINGS FOR EXACT LOCATION OF EQUIPMENT TO BE CONNECTED. CONTRACTOR IS RESPONSIBLE FOR PROVIDING CONNECTION TO ALL NEW OR RELOCATED EXISTING EQUIMPENT. C. PROVIDE 3/4" CONDUIT FROM FLAG POLE TO AN ACCESSIBLE LOCATION ABOVE CEILING IN THE BUILDING. PROVIDE PULL STRING. CAP FOR FUTURE USE. COORDINATE WITH SITE PLAN FOR LOCATION OF FLAG POLE. 7//015 7:35:10 AM E E1 EXISTING 100A DISTRIBUTION PANEL WITH 800A/3P BREAKER RISER DIAGRAM NTS 3 NEW MANUAL TRANSFER SWITCH 800A 4 POLE NEMA 3R J 1 EXISTING 800A/3P 800A FUSE 5 EXISTING CT CABINET M AS INDICATED BY: # 1. PROVIDE JUNCTION BOX TO CONNECT NEW MANUAL TRANSFER SWTICH TO EXISTING FEEDER SERVING EXISTING SWITCHBOARD.. PROVIDE (4) #500 KCMIL + #1/0 GND EACH IN () SETS OF 4" CONDUIT. 3. PROVIDE CAM LOCK CONNECTIONS FOR OWNER PORTABLE GENERATOR. COORDINATE NUMBER AND TYPE OF CONNECTIONS PER PHASE WITH OWNER. PROVIDE CONNECTION FOR NEUTRAL AND GROUND CONDUCTORS. PROVIDE A MINIMUM OF () CONNECTIONS FOR EACH PHASE, GROUND, AND NEUTRAL. 4. PROVIDE NEW MANUAL TRANSFER SWITCH IN NEMA 3R ENCLOSURE. SERVICE VOLTAGE IS 10/40 3 PHASE DELTA HIGH LEG. 5. REFER TO GROUNDING DETAIL THIS SHEET. NOTES: 1. PROVIDE 3/4" CONDUIT FROM INDOOR UNIT TO OUDTOOR UNIT TO ACCOMODATE CONTROL AND POWER CONDUCTORS. CABLING BETWEEN UNITS BY DIV 15 CONTRACTOR. PROVIDE NEW 0A/P BREAKER TO SERVE NEW UNIT IN EXISTING PANEL. COMBINE EXISTING 0A/1P BREAKERS AS REQUIRED TO ACCOMODATE NEW LOAD.. PROVIDE MOTOR RATED SWITCH, MOTOR OVERLOADS SHALL MATCH MOTOR RATING. EXTEND TO SPARE 0A/1P BREAKER IN EXISTING PANEL OR CONNECT TO EXISTING 0A/1P BREAKER WITH AVAILABLE CAPACITY. PARKH LL I SM PROFESS L ITH STATE I C & OF E IONAL COOPER N TEXAS JONATHAN LEE HARTMAN S E 07//15 D ENG, INC. INEER F KEY NOTES AS INDICATED BY: # D INTERVIEW A 109A 111A EVIDENCE B IT 111C 5 18A BREAKROOM NEW MANUAL TRANSFER SWTICH. REFER TO RISER DIAGRAM FOR ADDITIONAL INFORMATION.. NEW DUPLEX RECEPTACLE. EXTEND AND CONNECT TO 10V PANEL SERVING AREA. CIRCUIT A MAXIMUM OF 3 RECEPTACLES TO A CIRCUIT AND PROVIDE AT MINIMUM 1 CIRCUIT PER ROOM. (TYPICAL FOR NEW RECEPTACLES). IF RECEPTACLE BEING ADDED IS IN A SINGLE OCCUPANT OFFICE THE RECEPTACLE MAY BE EXTENDED AND CONNECTED WITH OTHER RECEPTACLES IN THE SPACE. 3. TYPICAL DATA OUTLET. PROVIDE 3/4" CONDUIT FROM SQUARE JUNCTION BOX WITH SINGLE GANG MUD RING TO AN ACCESSABLE LOCATION ABOVE CEILING. PROVIDE CONDUIT BUSHING. COMMUNICATIONS () CAT6 DATA CABLES FOR EACH LOCATION AND EXTEND TO WALL MOUNTED EQUIPMENT RACK PATCH PANEL. PROVIDE FOR TERMINATIONS AT EACH END. PROVIDE 10% SPARE CAPACITY FOR FUTURE CABLING. EXTEND DATA CABLING WITH THE USE OF "J" HOOKS. 4. PROVIDE HINGED WALL MOUNTED EQUIPMENT RACK. PROVIDE ATLAS WMA4-3; WMA-RR4 OR APROVED EQUAL. PROVIDE PATCH PANELS FOR NEW DATA CABLES. FOYER 100 LOBBY PATROL C.I.D. 109 WOMEN'S RR 15 JANITOR 14 MEN'S RR 16 17A WORK AREA 17 CORRIDOR 104 Space 19 CORRIDOR 11 CORRIDOR 110 RECEPTION 103 SGT INTERVIEW 107 CONFERENCE 108 MECH 13 ELEC 1 FOYER 10 C Space 9 CORRIDOR 117 CHIEF 116 SECRETARY 115 LT 114 LT 113 ADMIN SGT 11 K9 SGT 118 BORGER POLICE STATION/ XCEL BUILIDING REMODEL C1 COMMUNICATIONS PLAN 1/8" = 1'-0" INTERVIEW A 109A 111A EVIDENCE B IT 111C 18A BREAKROOM 18 GB B FOYER 100 LOBBY 101 PATROL 105 C.I.D. 109 WOMEN'S RR 15 JANITOR 14 MEN'S RR 16 17A WORK AREA W 5TH ST, BORGER, TX, KEY PLAN CORRIDOR 104 Space 19 CORRIDOR 11 RECEPTION 103 SGT 106 INTERVIEW 107 CONFERENCE 108 CORRIDOR 110 MECH 13 EXISTING PANEL B EXISTING PANEL C ELEC 1 FOYER 10 EXISTING PANEL A Space 9 CORRIDOR 117 K9 SGT 118 EXISTING PANEL D A CHIEF 116 SECRETARY 115 LT 114 LT 113 ADMIN SGT 11 07//15 ADDENDUM #1 1 07/07/15 100% CONSTRUCTION DOCUMENTS NO DATE DESCRIPTION ISSUING OFFICE: AMARILLO PROJECT NO: A1 POWER PLAN 1/8" = 1'-0" POWER AND COMMUNICATIONS PLAN E-101