Metering Box METERING AND AMBIENT HEATING FOR HEATING SYSTEM. Overview. Application PRODUCT DATA

Transcription

1 Metering Box METERING AND AMBIENT HEATING FOR HEATING SYSTEM Overview PRODUCT DATA The Honeywell Substations series consist of the following products: Metering Box (this datasheet) Heat Interface Unit, with instant domestic hot water production (see separate datasheet) To fullfil the plant requirements several options are available for each product range. Fig. 1. Unit as delivered, with blind pipes Application The Metering Box is designed to be applied in central heating systems for multi family dwellings where the domestic hot water production is centralized. The typical functions performed by the Metering Box are the following: Guarantee heat and water metering accuracy for each individual flat, with the optional possibility of connecting signals with a pulse or M-bus system for central reading Facilitate balancing by allowing a balancing device at each flat level. Balancing can be static or dynamic with differential pressure control Collect balancing and metering components in a single box, easier to install and control The Metering Box is delivered with predisposition for installation on site of the specific project required components for balancing and metering (list of suggested Honeywell components is described in this datasheet). Components not included with the unit, must be ordered separately. Before installing components, the Installer can perform a system cleansing and flushing to avoid fouling of the Unit with impurities or debris from the pipe work installation procedures. Fig. 2. Unit completed on site with project specific components (example, components not included with the Unit) Honeywell Subject to change EN0H-2611GE25 R0813

2 Hydraulic diagram (MB-123XX0X2-L) Function D C 1 8 B 1 9 A D-H line: heating return C-G line: heating flow B-F line: domestic cold water A-E line: domestic hot water 1. Manual isolation valve 2. On/Off motorized valve 3. Heat meter stub piece 4. Balancing valve stub piece 5. DPCV sensor holder 6. Heat meter sensor holder 7. Strainer 8. Domestic cold water stub piece 9. Domestic hot water stub piece H G F E The Metering Box unit can provide the following main functions: Heat and water Direct reading/pulse/m-bus metering system (see meters table) Balancing: the unit can equipped with a Honeywell Kombi-3- plus (static balancing) or Honeywell Kombi-3-plus and diaphragm (automatic balancing with differential pressure control) in order to provide the right commissioning of the heating system Heating system control: the unit is equipped with a motorised valve that receives a command from an external thermostat (optional) will allow to open or close the heating circuits Materials Cabinet made of sheet steel. Cabinet door (option) painted white according to RAL9010 Pipes made of copper Valve housings, fittings, union nuts and other components made of brass or other copper alloys Housings of actuator made of plastic Balancing valve stub piece made of steel Metering stub pieces made of plastic EN0H-2611GE25 R Honeywell Subject to change

3 V -V x V Hz <0.15W Radio 868 MHz IEC870-6 Pt 500 class Type440 Umgebungsklasse: C 2002 env: 5 C C er: 5 C...90 C Δp: 3K...100K DN15 PN16 q: 1,5m 3 /h Rücklauf q: 0,03m 3 /h Pt500 q: 3,0m 3 /h Kl. 3 M-Bus Qn 1,5 A/B H D C METERING BOX Mounting options Metering Box is design to be installed inside the building. The installation is in wall, horizontal in both directions (see Ordering information) and vertical. Install the product in place protected from frost. Product options The Metering Box product options available are: Power supply 230V (always) Balancing valve option: predisposition for static balancing / automatic balancing with differential pressure control Insulation: with or without pre-assembled insulation Heat Meter type: predisposition for Honeywell heat meters range (see table next pages) Water Meter type: predisposition for Honeywell water meters range (see table next pages) Heating circuit valve: 2-way: for variable flow system. To be used when a modulating pump is installed in the primary circuit and TRVs are installed in the radiator. 3-way: for constant flow system: To be used in the upper floor apartments in order to maintain the main heating rises hot. Frame door: must be ordered separately. Fig. 3. Installation without door Heatmeter type EW447A kwh Balancing and shutoff valve V5000 Sensor for EW773 EW447-EW452 V5010 V5012C Door 1 2 FD002 Note: color RAL 9010 Fig. 4. Installation with door EW773 Heatmeter Made in Germany M DE-10-MI004-PTB013 Typ: xxxxx Water meter EW 7730K1200 ΔT ΔT! Heatmeter heating conformity declared MBtm 3 MWh max GPM GJgal LCD Loop3: Installation S/N: qs: 3m 3/h qp: 1.5m3/h qi: 0.015m3/h PS/PN: 16 DN 15 IP 54 Oq: C O : C ΔO: C E1 / M1 P.-Year 2010 Q3: 2,5m 3 /h T90 MAP10 Q3/Q1: R125 E2 M-MKE XXXX EW743M1200 m 3 M LNE M-Bus m³ EW147P1201 Pulse 100 Display bracket EW130 EW147-EW DPCV Sensor Holder 2. Heat meter Sensor holder Fig. 5. Additional components to configure the unit according to the specific project requirements Honeywell Subject to change 3 EN0H-2611GE25 R0813

4 Dimensions Legenda: a - Hot sanitary water inlet b - Cold sanitary water inlet c - Inlet from centralized system d - Return to centralized system e - Hot sanitary water outlet f - Cold sanitary water outlet g - Heating outlet h - Heating return All hydraulic screwed connections according to ISO 228/1 G3/4 M EN0H-2611GE25 R Honeywell Subject to change

5 Ordering Information OS-No. Power supply Heating supply direction Insulation pre-assembled *Kv values before installation of balancing and metering components Valve type k v heating circuit k v domestic hot/cold water k v bypass MB-123XX0X2-L 230Vac Left to right No 2-way MB-123XX0X2-R 230Vac Right to left No 2-way MB-123XX0X3-L 230Vac Left to right No 3-way MB-123XX0X3-R 230Vac Right to left No 3-way MB-123XX1X2-L 230Vac Left to right Yes 2-way MB-123XX1X2-R 230Vac Right to left Yes 2-way MB-123XX1X3-L 230Vac Left to right Yes 3-way MB-123XX1X3-R 230Vac Right to left Yes 3-way FD002 Door Centralized heating Apartment side Apartment side Centralized heating Centralized heating Fig. 6. MB-123XX0X2-L Fig. 7. MB-123XX0X2-R Apartment side Apartment side Centralized heating Centralized heating Fig. 8. MB-123XX0X3-L Fig. 9. MB-123XX0X3-R Apartment side Apartment side Centralized heating Centralized heating Fig. 10. MB-123XX1X2-L Fig. 11. MB-123XX1X2-R Apartment side Apartment side Centralized heating Fig. 12. MB-123XX1X3-L Fig. 13. MB-123XX1X3-R Honeywell Subject to change 5 EN0H-2611GE25 R0813

6 Specifications Heating Circuit Water quality according to Kind of fluid VDI2035 max. glycol 30%* Max. temperature 90 C Max. operating pressure 6 bar Heating min/max flow rate According to heat meter installed Heating nominal flow rate According to heat meter installed Kv s value 3.68 m 3 /h (by-pass 0.9) Water lines Kind of fluid water Max. setting temperature 90 C for hot water line30 C for cold water line Max. operating pressure 6 bar Minimal flow rate According to water meters installed Max. flow rate According to water meters installed k vs value 6.62 m 3 /h Pipes Material Copper Size 18 x 1 mm Hydraulic connections Material Brass Size G 3/4" M Metal frame Material galvanized sheet 10/10 Electrical Actuator Function On/Off Rotation 90 Operation time 45 sec Position indicator led indicating the opening Tension 230 V ±10% Frequency 50 Hz Max. power consumption 4 W Max current of grey output 1 A Max current of auxiliary switch 1 A IP protection 54 Cable length 80 cm Ambient conditions Installation indoor Temperature range 5-55 C Humidity range 25-85% Motorized Valve Operation time ON/OFF type 45 sec Features Weight 8kg (*) Installing accessories in replacement of the stub pieces can reduce the percentage of permitted glycol. It is strong recommended the Customer to refer to the single components to be installed as limit parameter. Honeywell Subject to change 6 EN0H-2611GE25 R0813

7 Flow Diagrams Domestic hot/cold water line kg/h Flow rate l/sec Fig. 14. kv-value 6.62 m 3 /h 10 mbar 1000 Pa Pressure loss Heating supply line kg/h Flow rate l/sec Fig. 15. kv-value 4.93 m 3 /h 10 mbar 1000 Pa Pressure loss Honeywell Subject to change 7 EN0H-2611GE25 R0813

8 Heating return line kg/h Flow rate l/sec Fig. 16. kv-value 5.55 m 3 /h 10 mbar 1000 Pa Pressure loss EN0H-2611GE25 R Honeywell Subject to change

9 Electrical Specifications Mains connection: min. 3 x 1.5mm 2 Room thermostat: 2 x 0.75mm 2 M-Bus connection: 2 x 0.75mm 2 Electrical Connections Servocontrol with relay, 2-point control TA Phase Neutral Blue Brown Green (opens) Grey L1 White Pink M1 L1 Phase with open valve TA Room thermostat M1 Auxiliary micro switch free NOTE: NOTE: TA Phase Neutral Fig. 17. Servo control open Blue Brown Green (opens) Grey L1 White Pink M1 L1 Phase with open valve TA Room thermostat M1 Auxiliary micro switch free Fig. 18. Servo control closed The pictures show the wiring diagram of the complete 2-point servocontrol (with 1 built-in auxiliary microswitch). The servocontrol is shown open and closed respectively. When the phase is on green wire, the valve connected to the servocontrol opnes; on the contrary, if there is no phase on that wire, the valve closes. The electrical connection of the motorized valve must be provided in a professional plastic box IP54 or higher (not included) Compatible Honeywell wired thermostats Range Wired thermostats Comment CM700 CM900 CMT701A1006 CMT702A1004 CMT702A1012 CMT707A1003 CM901i CM907i 1 day heating program, include SPDT relay (potential free contact) 5+2 days heating program, 4 switch points, include SPDT relay (potential free contact) 5+2 days heating program, 6 switch points, include SPDT relay (potential free contact) 7 days heating program, include SPDT relay (potential free contact) 1 day heating program, LCD display, include SPDT relay (potential free contact) 7 days heating program, LCD display, include SPDT relay (potential free contact) Honeywell Subject to change 9 EN0H-2611GE25 R0813

10 Metering Options Optimal combination R Possible alternative for later installation of remote readout system - additional parts required Ultrasonic heat meters (Qp=1.5m 3 /h, DN15, 110mm length) Water meters EW1000AZ1201 EW1001AZ1201 EW147P1201 EW148P1201 EW1300BF1200 EW1301BF1200 EW1300BM1200 EW1301BM1200 Singlejet water meter (DN15, 110mm length) Multijet water meter (DN15, 110mm length) Q3 = 2.5m 3 /h Q3 = 2.5m 3 /h Qn = 1.5m 3 /h Qn = 1.5m 3 /h Q3 = 2.5m 3 /h Q3 = 2.5m 3 /h Q3 = 2.5m 3 /h Q3 = 2.5m 3 /h 30 C 90 C 30 C 90 C 30 C 90 C 30 C 90 C Interface None None Pulse output Pulse output RF RF M-Bus M-Bus EW7730A1200 None R R EW7730F1200 RF R R EW7730K1200 for heating M-Bus + 2 pulse inputs EW7730M1200 M-Bus EW7731A1200 None R R EW7731F1200 RF R R EW7731K1200 for heating and chilled water M-Bus + 2 pulse inputs EW7731M1200 M-Bus Multijet heat meters (DN15) EW447A1200 None EW447F1200 RF for heating EW447P1200 Pulse output EW447M1200 M-Bus EW450A1200 None EW450F1200 for heating and RF EW450P1200 chilled water Pulse output EW450M1200 M-Bus NOTE: Qp is used for heat meters, Qn is used for water meters to EN1434 and Q3 is used for water meters to MID. NOTE: To evaluate properly RF applications it is suggested to contact Honeywell personnel. EN0H-2611GE25 R Honeywell Subject to change

11 Accessories Heat meter accessories Honeywell wireless individual room control system evohome ATP921G1034 including antenna BDR91 and table support ATF100 Honeywell thermostat Thera-4 Classic Thera-4 Design Thera-200 Design Bluetooth optohead T3001W0 T2001W0 T2021W0 T4021 T4221 T4321 T4111 EWA Hydro-Center 25 Solar M-Bus master for max. 25 M-Bus meters, built in EW535M0055 data logger with 2 MByte memory, for 12V solar power supply Hydro-Port Pulse Converter for metering devices EW535M0056 with pulse output to M-Bus, 2 pulse inputs Hydro-Port Analog Converter for metering devices, with analogue 0(4)..20 ma interface to M-Bus, EW535M analogue inputs, 1 analogue output, 1 input for PT temperature probe Hydro-Port Control M-BUS relay module with digital state inputs. 2 bistable EW535M0059 relay outputs and 2 digital state inputs M-Bus Receiver 868MHz Hydro-Radio 868 receiver for EW535M0131 stationary installation with Izar- Center 60/120/250 interface GSM Modem for Hydro- Center EW535M0147 GSM modem for Hydro-Center incl. accessories Izar-Center 60 M-Bus master for max. 60 M- EW535M5777 Bus meters Izar-Center 120 M-Bus master for max. 120 M- EW535M5778 Bus meters Izar-Center 250 M-Bus master for max. 250 M- EW535M5780 Bus meters Izar-Center 60 Memory M-Bus master for EW535M5781 max. 60 M-Bus meters, data logger with 256 MByte memory Izar-Center 120 Memory M-Bus master for EW535M5782 max. 120 M-Bus meters, data logger with 256 MByte memory Izar-Center 250 Memory M-Bus master for EW535M5783 max. 250 M-Bus meters, data logger with 256 MByte memory GSM Modem for Izar-Center 60/120/250 GSM/GPRS modem for Izar- Center incl. accessories EW535M5787 Hydro-Center 25 M-Bus master for max. 25 M-Bus meters EW535M0093 Hydro-Center 25 Memory M-Bus master for max. 25 M-Bus meters, built-in EW535M0094 data logger with 2 MByte memory Honeywell Subject to change 11 EN0H-2611GE25 R0813

12 Environmental and Combustion Controls Honeywell GmbH Hardhofweg MOSBACH GERMANY Phone: +49 (6261) 810 Fax: +49 (6261) EN0H-2611GE25 R0813 August Honeywell International Inc. Subject to change without notice Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Z.A. La Pièce 16, 1180 Rolle, Switzerland or its Authorized Representative.