E5CN/E5CN-U (48 x 48 mm)

Transcription

1 Basic-type Digital Temperature Controller /-U (48 x 48 mm) CSM -U_DS_E_5_7 New 48 x 48-mm Basic Temperature Controller with Enhanced Functions and Performance. Improved Indication Accuracy and Preventive Maintenance Function. Indication Accuracy Thermocouple input: ±.3% of PV (previous models: ±.5%) Pt input: ±.% of PV (previous models: ±.5%) Analog input: ±.% FS (previous models: ±.5%) New -U s (Plug-in s) with analog inputs and current outputs. A PV/SV-status display function can be set to automatically alternate between displaying the status of the Temperature Controller (auto/ manual, RUN/STOP, and alarms) and the PV or SV. Preventive maintenance for relays in the Temperature Controller using a Control Output / Counter. Main I/O Functions mm mm -U For the most recent information on models that have been certified for safety standards, refer to your OMR website. Refer to Safety Precautions for E5@N/E5@N-H. Refer to Operation for E5@N/E5@N-H for operating procedures. Event Inputs None Two -level Display: PV and SV 4-digit Display Sensor Inputs Universal thermocouple/pt inputs (s with temperature inputs) Analog current/voltage inputs (s with analog inputs) Indication Accuracy Thermocouple input: ±.3% of PV Pt input: ±.% of PV Analog input: ±.% FS Sampling Period 5 ms Control Output None Voltage output (for driving SSR) Control Output Long-life relay output (hybrid) Auxiliary Outputs None One Two Auto/manual switching Temperature Controller status display Simple program function Control output / count alarm PV change rate alarm s also available with communications This data sheet is provided as a guideline for selecting products. Be sure to refer to the following user manuals for application precautions and other information required for operation before attempting to use the product. /E5AN/E5EN/E5GN Digital Temperature Controllers User's Manual Basic Type (Cat. No. H6) /E5AN/E5EN/E5GN Digital Temperature Controllers Manual Basic Type (Cat. No. H8)

2 Lineup /-U control output or auxiliary outputs Temperature input control outputs auxiliary outputs Terminal block control output or auxiliary outputs Basic Type Analog input control outputs auxiliary outputs Plug-in Temperature input Analog input control output control output,, or auxiliary outputs,, or auxiliary outputs Note: s with one control output and one or two auxiliary outputs and models with two control outputs can be used for heating/cooling control. Number Structure Number Legend Controllers -@@M@@-@ Control Output R: Q: C: Y: Long-life relay output (hybrid) *. Auxiliary Outputs * Blank: None : Two outputs 3. Option M: Option Unit can be mounted. 4. Input Type T: Universal thermocouple/platinum resistance thermometer L: Analog current/voltage input 5. Power Supply Voltage Blank: to 4 VAC D: 4 VAC/VDC 6. Case Color Blank: Black W: Silver 7. Terminal Cover -5: With terminal cover Option Units E53-CN@@@ 3 4. Applicable Controller CN: or -H. Function Blank: None Q: Control output (voltage for driving SSR) P: Power supply for sensor 3. Function Blank: None H: Heater burnout/ssr failure/heater overcurrent detection (CT) HH: Heater burnout/ssr failure/heater overcurrent detection (CT) B: Two event inputs 3: communications H3: Heater burnout/ssr failure/heater overcurrent detection (CT) + communications HB: Heater burnout/ssr failure/heater overcurrent detection (CT) + Two event inputs HH3: Heater burnout/ssr failure/heater overcurrent detection (CT) + communications 4. Version N: Applicable only to models released after January 8 Note:. Not all combinations of function and function specifications are possible for Option Units (E53-@@@@).. Estimates can be provided for coatings and other specifications that are not given in the datasheet. Ask your OMR representative for details. *. Always connect an AC load to a long-life relay output. The output will not turn if a DC load is connected because a triac is used for switching the circuit. For details, check the conditions in Ratings. *. Auxiliary outputs are contact outputs that can be used to output alarms or results of logic operations.

3 Ordering Information Controllers with Terminal Blocks Size /6 DIN (W H D) Case color Black Silver Power supply voltage to 4 VAC 4 VAC/VDC to 4 VAC 4 VAC/VDC to 4 VAC Note: s with analog inputs do not have temperature unit indicators. Option Units One of the following Option Units can be mounted to provide the with additional functions. /-U Input type Auxiliary outputs Control output Thermocouple or Resistance thermometer Thermocouple or Resistance thermometer Analog (current/voltage) Analog (current/voltage) Thermocouple or Resistance thermometer 4 VAC/VDC 3-phase heater burnout/ssr failure/ Heater overcurrent detection Heater burnout/ssr failure/heater overcurrent detection Heater burnout/ssr failure/heater overcurrent detection Heater burnout/ssr failure/heater overcurrent detection Heater burnout/ssr failure/heater overcurrent detection 3-phase heater burnout/ssr failure/ Heater overcurrent detection None None None None Functions Event inputs Event inputs Event inputs Control output (Voltage for driving SSR) Control output (Voltage for driving SSR) Control output (Voltage for driving SSR) Long-life relay output (hybrid) Long-life relay output (hybrid) Long-life relay output (hybrid) External power supply for ESB External power supply for ESB External power supply for ESB -RMT-5 -QMT-5 -CMT-5 -RMT-5 -QMT-5 -CMT-5 -YMT-5 -RMTD-5 -QMTD-5 -CMTD-5 -RMTD-5 -QMTD-5 -CMTD-5 -RML-5 -QML-5 -CML-5 -RML-5 -QML-5 -CML-5 -YML-5 -RMLD-5 -QMLD-5 -CMLD-5 -RMT-W-5 -QMT-W-5 -CMT-W-5 -RMT-W-5 -QMT-W-5 -CMT-W-5 -YMT-W-5 -RMTD-W-5 -QMTD-W-5 -CMTD-W-5 (See Note.) E53-CNHH3N E53-CNHBN E53-CNQ3N E53-CNPBN E53-CNPHN E53-CNP3N E53-CNH3N E53-CN3N E53-CNBN E53-CNQHN E53-CNQHHN Control output Event inputs E53-CNQBN (Voltage for driving SSR) Note:. Option Units cannot be used for plug-in models. These Option Units are applicable only to models released after January 8.. If models with heater burnout detection are used together with the -C@ Temperature Controller and control output (current output) is assigned to the heating control output, heater burnout detection will be disabled. 3

4 Number Structure Number Legend (Plug-in-type Controllers) /-U 3 4. Output Type R: Q: C:. Number of Alarms Blank: No alarm : One alarm : Two alarms 3. Input Type T: Universal thermocouple/platinum resistance thermometer L: Analog Input 4. Plug-in type U: Plug-in type Ordering Information Plug-in-type Controllers Size /6 DIN Black Case color Power supply voltage to 4 VAC 4 VAC/VDC Note: s with analog inputs do not have temperature unit indicators. Input type Auxiliary outputs Control output Thermocouple or resistance thermometer Analog (current/voltage) Thermocouple or resistance thermometer None None -RTU -QTU -CTU -RTU -QTU -CTU -RTU -QTU -CTU -RLU -QLU -CLU -RLU -QLU -CLU -RTDU -QTDU -CTDU -RTDU -QTDU -CTDU -RTDU -QTDU -CTDU 4

5 /-U Accessories (Order Separately) USB-Serial Conversion Cable Adapter Terminal Cover E58-CIFQ Connectable models Terminal block models Y9F-45 Note: Use this Adapter when the panel has been previously prepared for the Connectable models Terminal block models E53-COV7 Note: The Terminal Cover comes with the models. Waterproof Packing Y9S-9 Note: The Waterproof Packing is included with the Controller only for models with terminal blocks. Current Transformers (CTs) Hole diameter 5.8 dia. E54-CT. dia. E54-CT3 DIN Track Mounting Adapter Sockets (for Plug-in s) Front cover Type Front-connecting Socket Y9F-5 Front-connecting Socket with Finger Protection Back-connecting Socket Terminal Cover for Back-connecting socket with Finger Protection PCF- PCF--E P3GA- Y9A-48G Hard Front Cover Soft Front Cover Type Y9A-48B Y9A-48D C-Thermo Support Software EST-C-MV4 5

6 Specifications Ratings Power supply voltage Operating voltage range Power consumption Sensor input -U Input impedance Control method Control outputs Voltage output (for driving SSR) /-U No D in model number: to 4 VAC, 5/6 Hz D in model number: 4 VAC, 5/6 Hz; 4 VDC 85% to % of rated supply voltage to 4 VAC: 7.5 VA (max.) (-RT at VAC: 3. VA) 4 VAC/VDC: 5 VA/3 W (max.) (-RTD at 4 VAC:.7 VA) to 4 VAC: 6 VA (max.) 4 VAC/VDC: 3 VA/ W (max.) (models with current output: 4 VA/ W) s with temperature inputs Thermocouple: K, J, T, E, L, U, N, R, S, B, W, or PL II Platinum resistance thermometer: Pt or JPt Infrared temperature sensor (ESB): to 7 C, 6 to C, 5 to 65 C, or to 6 C Voltage input: to 5 mv s with analog inputs Current input: 4 to ma or to ma Voltage input: to 5 V, to 5 V, or to V Current input: Ω max., Voltage input: MΩ min. (Use a : connection when connecting the ES-HB.) / control or -PID control (with auto-tuning) ST-NO, 5 VAC, 3 A (resistive load), electrical life:, operations, minimum applicable load: 5 V, ma DT, 5 VAC, 3 A (resistive load), electrical life:, operations, minimum applicable load: -U 5 V, ma -U Output voltage: VDC ±% (PNP), max. load current: ma, with short-circuit protection circuit 4 to ma DC/ to ma DC, load: 6 Ω max., resolution: approx., Long-life relay output ST-NO, 5 VAC, 3 A (resistive load), electrical life:,, operations, load power supply voltage: 75 to 5 VAC (DC loads cannot be connected.), minimum applicable load: 5 V, ma, leakage current: 5 ma max. (5 VAC, 6 Hz) or max. (Depends on the model.) : ST-NO, 5 VAC, 3 A (resistive load), electrical life:, operations, minimum applicable load: 5 V, ma Number of outputs Auxiliary outputs Output specifications Number of inputs Event External contact Contact input: : kω max., : kω min. inputs input Non-contact input: : Residual voltage:.5 V max., : Leakage current:. ma max. specifications Current flow: Approx. 7 ma per contact External power supply for ESB VDC ±%, ma, short-circuit protection circuit provided Setting method Digital setting using front panel keys Indication method -segment digital display and individual indicators (7-segment display also possible) Character height: PV: mm, SV: 6.5 mm Multi Up to four set points ( to 3) can be saved and selected using event inputs, key operations, or serial communications. Bank switching Not supported Manual output, heating/cooling control, loop burnout alarm, ramp, other alarm functions, heater burnout detection (including SSR failure and heater overcurrent detection), 4% AT, % AT, MV limiter, input Other functions digital filter, self-tuning, temperature input shift, run/stop, protection functions, control output / counter, extraction of square root, MV change rate limit, logic operations, PV/SV status display, simple program, automatic cooling coefficient adjustment Ambient operating temperature to 55 C (with no condensation or icing), for 3-year warranty: to 5 C Ambient operating humidity 5% to 85% Storage temperature 5 to 65 C (with no condensation or icing) 6

7 /-U Input Ranges Thermocouple/Platinum Resistance Thermometer (Universal Inputs) Temperature range ( C) Input Type Platinum resistance thermometer Shaded settings are the default settings. The applicable standards for the input types are as follows: K, J, T, E, N, R, S, B: JIS C 6-995, IEC 584- L: Fe-CuNi, DIN U: Cu-CuNi, DIN W: W5Re/W6Re, ASTM E s with Analog Inputs Thermocouple Name Pt JPt K J T E L U N R S B W PL II Setting number Input Type Current Voltage Input specification 4 to ma to ma to 5 V to 5 V to V Usable in the following ranges by scaling: Setting range 999 to 9999, 99.9 to 999.9, 9.99 to or.999 to Setting number 3 4 Shaded settings are the default settings. 8 3 Infrared temperature sensor to 7 C 6 to C 5 to 65 C to 6 C Analog input to 5 mv Usable in the following ranges by scaling: 999 to 9999 or 99.9 to JPt: JIS C , JIS C Pt: JIS C , IEC 75 PL II: According to Platinel II electromotive force charts from BASF (previously Engelhard) 7

8 /-U Alarm Outputs Each alarm can be independently set to one of the following 3 alarm types. The default is : Upper limit. Auxiliary outputs are allocated for alarms. delays and delays ( to 999 s) can also be specified. Note: For models with heater burnout, SSR failure, and heater overcurrent detection, alarm will be an OR output of the alarm selected from the following alarm types and the alarms for heater burnout, SSR failure, and heater overcurrent. To output only a heater burnout alarm, SSR failure alarm, and heater overcurrent alarm for alarm, set the alarm type to (i.e., no alarm function). Set value Alarm type *. With set values, 4 and 5, the upper and lower limit values can be set independently for each alarm type, and are expressed as L and H. *. Set value:, Upper- and lower-limit alarm *3. Set value: 4, Upper- and lower-limit range *4. Set value: 5, Upper- and lower-limit with standby sequence For Upper- and Lower-Limit Alarm Described Above Case and Always when the upper-limit and lower-limit hysteresis overlaps. Case 3: Always Alarm output operation When alarm value is positive When alarm value is negative Description of function Alarm function Output No alarm L H Set the deviation in the set point by setting the alarm * Upper- and lower-limit * upper limit (H) and alarm lower limit (L). Upper-limit 3 Lower-limit 4 * Upper- and lower-limit range *3 5 * Upper- and lower-limit with standby sequence 6 Upper-limit with standby sequence 7 Lower-limit with standby sequence 8 Absolute-value upper-limit 9 Absolute-value lower-limit Absolute-value upper-limit with standby sequence Absolute-value lower-limit with standby sequence LBA (alarm type only) --- *7 3 PV change rate alarm --- *8 Case L H H <, L > H < L Case L H H <, L > H < L Case L H H >, L < H > L Case L H H >, L < H > L *5 Case 3 (Always ) H H L H L L Case 3 (Always ) H H L H L L L H L H H <, L < H <, L > H L H >, L < H L H <, L < H <, L > H L H >, L < H L *4 Set the upward deviation in the set point by setting the alarm value (). Set the downward deviation in the set point by setting the alarm value (). Set the deviation in the set point by setting the alarm upper limit (H) and alarm lower limit (L). A standby sequence is added to the upper- and lower-limit alarm (). *6 A standby sequence is added to the upper-limit alarm (). *6 A standby sequence is added to the lower-limit alarm (3). *6 The alarm will turn if the process value is larger than the alarm value () regardless of the set point. The alarm will turn if the process value is smaller than the alarm value () regardless of the set point. A standby sequence is added to the absolute-value upper-limit alarm (8). *6 A standby sequence is added to the absolute-value lower-limit alarm (9). *6 *5. Set value: 5, Upper- and lower-limit with standby sequence Always when the upper-limit and lower-limit hysteresis overlaps. *6. Refer to the /E5AN/E5EN/E5GN Digital Temperature Controllers User's Manual Basic Type (Cat. No. H6) for information on the operation of the standby sequence. *7. Refer to the /E5AN/E5EN/E5GN Digital Temperature Controllers User's Manual Basic Type (Cat. No. H6) for information on the loop burnout alarm (LBA). *8. Refer to the /E5AN/E5EN/E5GN Digital Temperature Controllers User's Manual Basic Type (Cat. No. H6) for information on the PV change rate alarm. 8

9 /-U Characteristics Indication accuracy Thermocouple: * Terminal block models (): (±.3% of indicated value or ± C, whichever is greater) ± digit max. Plug-in models (-U): (±% of indicated value or ± C, whichever is greater) ± digit max. Platinum resistance thermometer input: Terminal block models () and plug-in models (-U): (±.% of indicated value or ±.8 C, whichever is greater) ± digit max. Analog input: Terminal block models () and plug-in models (-U): ±.% FS ± digit max. CT input: Terminal block models (): ±5% FS ± digit max. Thermocouple input (R, S, B, W, PL II): Terminal block models (): (±% of PV or ± C, whichever is greater) ± digit max. Influence of temperature * Plug-in models (-U): (±% of PV or ± C, whichever is greater) ± digit max. Other thermocouple input: *3 Terminal block models (): (±% of PV or ±4 C, whichever is greater) ± digit max. Plug-in models (-U): (±% of PV or ±4 C, whichever is greater) ± digit max. Platinum resistance thermometer input: Terminal block models () and plug-in models (-U): Influence of voltage * (±% of PV or ± C, whichever is greater) ± digit max. Analog input: Terminal block models () and plug-in models (-U): (±%FS) ± digit max. Input sampling period 5 ms s with thermocouple/platinum resistance thermometer input (universal input):. to EU (in units of. EU) *4 Hysteresis s with analog input:. to 99.99% FS (in units of.% FS) s with thermocouple/platinum resistance thermometer input (universal input):. to EU (in units of. EU) *4 Proportional band (P) s with analog input:. to 999.9% FS (in units of.% FS) Integral time (I) to 3999 s (in units of s) Derivative time (D) to 3999 s (in units of s) *5 Control period.5, to 99 s (in units of s) Manual reset value. to.% (in units of.%) Alarm setting range 999 to 9999 (decimal point position depends on input type) Affect of signal source resistance Insulation resistance Dielectric strength Vibration Malfunction resistance Destruction Shock Malfunction resistance Destruction Weight -U Degree of protection -U Memory protection Setup Tool Setup Tool port Standards Approved standards *7 Conformed standards Thermocouple:. C/Ω max. ( Ω max.) Platinum resistance thermometer:. C/Ω max. ( Ω max.) MΩ min. (at 5 VDC),3 VAC, 5 or 6 Hz for min (between terminals with different charge) to 55 Hz, m/s for min each in, Y, and Z directions to 55 Hz,.75-mm single amplitude for hrs each in, Y, and Z directions m/s, 3 times each in, Y, and Z directions 3 m/s, 3 times each in, Y, and Z directions Controller: Approx. g, Mounting Bracket: Approx. g Controller: Approx. g, Mounting Bracket: Approx. g Front panel: IP66, Rear case: IP, Terminals: IP Front panel: IP5, Rear case: IP, Terminals: IP Non-volatile memory (number of writes:,, times) C-Thermo version 4. or higher Provided on the bottom of the. Use this port to connect a computer to the when using the Setup Tool. An E58-CIFQ USB-Serial Conversion Cable is required to connect the computer to the. *6 UL 6-, CSA C. No. -, KOSHA certified (some models) *8 EN 6- (IEC 6-): Pollution level, overcurrent category II, Lloyd's standards *9 EMI: EN 636 Radiated Interference Electromagnetic Field Strength: EN 55 Group, class A Noise Terminal Voltage: EN 55 Group, class A EMS: EN 636 ESD Immunity: EN 6-4- EMC Electromagnetic Field Immunity: EN Burst Noise Immunity: EN Conducted Disturbance Immunity: EN Surge Immunity: EN Power Frequency Magnetic Field Immunity: EN Voltage Dip/Interrupting Immunity: EN 6-4- *. The indication accuracy of K thermocouples in the to 3 C range, T and N thermocouples at a temperature of C max., and U and L thermocouples at any temperatures is ± C ± digit max. The indication accuracy of the B thermocouple at a temperature of 4 C max. is not specified. The indication accuracy of B thermocouples in the 4 to 8 C range is ±3 C max. The indication accuracy of the R and S thermocouples at a temperature of C max. is ±3 C ± digit max. The indication accuracy of W thermocouples is ±.3 of PV or ±3 C, whichever is greater, ± digit max. The indication accuracy of PL II thermocouples is ±.3 of PV or ± C, whichever is greater, ± digit max. *. Ambient temperature: C to 3 C to 55 C, Voltage range: % to % of rated voltage *3. K thermocouple at C max.: ± max. *4. EU stands for Engineering Unit and is used as the unit after scaling. For a temperature sensor, the EU is C or F. *5. When robust tuning (RT) is, the differential time is. to (in units of. s). *6. External communications () and cable communications for the Setup Tool can be used at the same time. *7. The -U plug-in model is certified for UL listing only when used together with the OMR PCF- or PCF--E Socket. The P3GA- is not certified for UL listing. *8. Access the following website for information on certified models. *9. Refer to information on maritime standards in Safety Precautions for E5@N/E5@N-H for compliance with Lloyd's Standards. 9

10 /-U USB-Serial Conversion Cable Applicable OS Windows P/Vista/7/8 Applicable software C-Thermo version 4 or higher Applicable models E5AN/E5EN//-U/E5AN-H/ E5EN-H/-H/E5GN USB interface standard Conforms to USB Specification.. DTE speed 384 bps Connector specifications Power supply Power supply voltage Current consumption Ambient operating temperature Ambient operating humidity Computer: USB (type A plug) Temperature Controller: Setup Tool port (on bottom of Controller) Bus power (Supplied from USB host controller.) 5 VDC 7 ma to 55 C (with no condensation or icing) % to 8% Storage temperature to 6 C (with no condensation or icing) Storage humidity % to 8% Altitude, m max. Weight Approx. g Note: A driver must be installed in the personal computer. Refer to installation information in the operation manual for the Conversion Cable. Specifications Transmission line connection method : Multipoint (two-wire, half duplex) Synchronization method Start-stop synchronization Protocol CompoWay/F, SYSWAY, or Modbus Baud rate, 4, 48, 96, 9, 384, or 576 bps Transmission code ASCII Data bit length * 7 or 8 bits Stop bit length * or bits Vertical parity (none, even, odd) Error detection Frame check sequence (FCS) with SYSWAY Block check character (BCC) with CompoWay/F or CRC-6 Modbus Flow control None Interface Retry function None buffer 7 bytes response wait time to 99 ms Default: ms * The baud rate, data bit length, stop bit length, and vertical parity can be individually set using the Setting Level. Current Transformer (Order Separately) Ratings Dielectric strength, VAC for min Vibration resistance 5 Hz, 98 m/s Weight Accessories (E54-CT3 only) E54-CT: Approx..5 g, E54-CT3: Approx. 5 g Armatures () Plugs () Heater Burnout Alarms, SSR Failure Alarms, and Heater Overcurrent Alarms CT input (for heater current detection) Maximum heater current Input current indication accuracy Heater burnout alarm setting range * SSR failure alarm setting range * Heater overcurrent alarm setting range *3 s with detection for single-phase heaters: One input s with detection for single-phase or three-phase heaters: Two inputs 5 A AC ±5% FS ± digit max.. to 49.9 A (in units of. A) Minimum detection time: ms. to 49.9 A (in units of. A) Minimum detection time: ms. to 49.9 A (in units of. A) Minimum detection time: ms *. For heater burnout alarms, the heater current will be measured when the control output is, and the output assigned to the alarm function will turn if the heater current is lower than the set value (i.e., heater burnout detection current value). *. For SSR failure alarms, the heater current will be measured when the control output is, and the output assigned to the alarm function will turn if the heater current is higher than the set value (i.e., SSR failure detection current value). *3. For heater overcurrent alarms, the heater current will be measured when the control output is, and the output assigned to the alarm function will turn if the heater current is higher than the set value (i.e., heater overcurrent detection current value). Electrical Life Expectancy Curve for Relays (Reference Values) Life ( 4 operations) VAC, 3 VDC (resistive load) cosφ = Switching current (A) Note: Do not connect a DC load to a Controller with a Long-life Relay Output.

11 External Connections /-U A voltage output (control output, for driving SSR) is not electrically insulated from the internal circuits. When using a grounding thermocouple, do not connect any of the control output terminals to ground. (If the control output terminals are connected to ground, errors will occur in the measured temperature values as a result of leakage current.) Consult with your OMR representative before using the external power supply for the ESB for any other purpose. Controllers Control output Long-life relay output 5 VAC, 3 A (resistive load) 5 VAC, 3 A (resistive load) VDC, ma to ma DC 4 to ma DC Load: 6 Ω max. The E5@N-@@@T@ is set for a K-type thermocouple (input type = 5) by default. An input error (s.err) will occur if the input type setting does not agree with the temperature sensor. Check the input type. Auxiliary outputs (relay outputs) 5 VAC, 3 A (resistive load) Auxiliary outputs (relay outputs) Control output VDC, ma ma V Analog input Control output A B B TC/Pt universal input Auxiliary output Auxiliary output Input power supply to 4 VAC 4 VAC/VDC (no polarity) A heater burnout alarm, heater short alarm, heater overcurrent alarm, or input alarm is sent to the output to which the alarm function is assigned. Option Units E53-CNHH3N () and CT B(+) A( ) 3 CT CT EV CT E53-CNHBN Event inputs and CT EV 3 E53-CNQ3N () and Control Output B(+) A( ) 3 + Control output E53-CNPBN Event Inputs and External Power Supply EV 3 EV + External VDC, power supply ma E53-CNPHN External Power Supply and CT External + power supply CT VDC, ma 3 E53-CNP3N () and External Power Supply B(+) A( ) 3 + External VDC, power supply ma E53-CNH3N () and CT E53-CN3N () E53-CNBN Event inputs E53-CNQHN Control Output and CT E53-CNQHHN Control Output and CT E53-CNQBN Event Inputs and Control Output B(+) A( ) 3 CT B(+) A( ) 3 EV EV 3 + Control output 3 CT + Control output CT CT 3 EV 3 EV + Control output -U Control output (three terminals used) DT, 5 VAC, 3 A (resistive load) Voltage output (for driving SSR) VDC, ma 4 to ma DC to ma DC Load: 6 W max. The E5@N-@@@T@ is set for a K-type thermocouple (input type = 5) by default. An input error (s.err) will occur if the input type setting does not agree with the temperature sensor. Check the input type. m A Analog input Control output Note: For the Wiring Socket, purchase the PCF- or PG3A- separately. V A B B TC/Pt universal input Auxiliary output 5 VAC, 3 A (resistive load) (s) Auxiliary output Auxiliary output (Control output (cooling side)) Input power supply to 4 VAC 4 VAC/VDC (no polarity) An input error is sent to the output to which the alarm function is assigned.

12 Isolation/Insulation Block Diagrams -U /-U Nomenclature -U The front panel is the same for the and -U. Temperature unit Operation indicators No. display No. display Level Key Up Key Mode Key Down Key Dimensions (Unit: mm) Terminal s Panel Cutout Mounted Separately Group Mounted (48 number of units.5) min. Group mounting does not allow waterproofing. Waterproof Mounting Adapter Packing (Accessory) (Accessory) Terminal Cover (E53-COV7) (Accessory) Note: The terminal block cannot be removed Recommended panel thickness is to 5 mm. Group mounting is not possible in the vertical direction. (Maintain the specified mounting space between Controllers.) To mount the Controller so that it is waterproof, insert the waterproof packing onto the Controller. When two or more Controllers are mounted, make sure that the surrounding temperature does not exceed the allowable operating temperature specified in the specifications. -U Plug-in s (84.7) Panel Cutout Mounted Separately Group Mounted (48 number of units.5) Mounting Adapter (Accessory) 6 min Recommended panel thickness is to 5 mm. Group mounting is not possible in the vertical direction. (Maintain the specified mounting space between Controllers.) When two or more Controllers are mounted, make sure that the surrounding temperature does not exceed the allowable operating temperature specified in the specifications.

13 /-U Accessories (Order Separately) USB-Serial Conversion Cable E58-CIFQ (,) 5 LED indicator (SD),765 USB connector (type A plug) LED indicator (RD) Serial connector Terminal Cover E53-COV7 Waterproof Packing Y9S-9 (for DIN 48 48) Note: The E53-COV cannot be used. Order the Waterproof Packing separately if it becomes lost or damaged. The Waterproof Packing can be used to achieve an IP66 degree of protection. (Deterioration, shrinking, or hardening of the waterproof packing may occur depending on the operating environment. Therefore, periodic replacement is recommended to ensure the level of waterproofing specified in IP66. The time for periodic replacement depends on the operating environment. Be sure to confirm this point at your site. Consider one year a rough standard. OMR shall not be liable for the level of water resistance if the customer does not perform periodic replacement.) The Waterproof Packing does not need to be attached if a waterproof structure is not required. 9. 3

14 /-U Current Transformers E54-CT dia..5 Two, 3.5 dia E54-CT Thru-current (Io) vs. Output Voltage (Eo) (Reference Values) Maximum continuous heater current: 5 A (5/6 Hz) Number of windings: 4± Winding resistance: 8± Ω V 5 Hz Output voltage (Eo) V (r.m.s.) mv kω Ω Distortion factor % 3% % E54-CT dia. RL = Ω dia. 9 μv E54-CT3 Accessory Armature Approx. 3 dia. Plug Two, M3 (depth: 4) 3 Connection Example Armature Plug Lead ma, A Thru-current (Io) A (r.m.s.) E54-CT3 Thru-current (Io) vs. Output Voltage (Eo) (Reference Values) Maximum continuous heater current: A (5/6 Hz) (Maximum continuous heater current for the Temperature Controller is 5 A.) Number of windings: 4± Winding resistance: 8±.8 Ω Output voltage (Eo) V (r.m.s.) V 5 Hz mv kω 5 Ω Ω 5 Ω RL = Ω Distortion factor % 3% % Approx. 6 dia. () μv ma, A Thru-current (Io) A (r.m.s.)

15 /-U Adapter Y9F-45 Note:. Note:. Use this Adapter when the panel has already been prepared for the The Adapter is available only in black to Fixture (Accessory) Mounted to 7 7 Panel ( to 8 mm) DIN Track Mounting Adapter Y9F-5 Note: This Adapter cannot be used together with the Terminal Cover. Remove the Terminal Cover to use the Adapter (to back of ) Mounted to 48.5

16 /-U -U Wiring Socket Front-connecting Socket PCF- Eleven, M sems screws Terminal Layout/Internal Connections (Top View) 7 max Mounting Holes Two, 4.5 dia. mounting holes Two, 4.5-dia. holes 9 3 4±. Note: Can also be mounted to a DIN track. 4 5 max. 3. max. Note: A model with finger protection (PCF--E) is also available. Back-connecting Socket P3GA- 7 dia Terminal Layout/Internal Connections (Bottom View) Note:. Using any other sockets will adversely affect accuracy. Use only the specified sockets.. A Protective Cover for finger protection (Y9A-48G) is also available. 6

17 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMR representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMR MAKES NO WARRANTY OR REPRESENTATI, EPRESS OR IMPLIED, ABOUT N-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron s sole obligation hereunder shall be, at Omron s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See or contact your Omron representative for published information. Limitation on Liability; Etc. OMR COMPANIES SHALL NOT BE LIABLE FOR ECIAL, INDIRECT, INCIDENTAL, OR CSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTI OR COMMERCIAL LOSS IN ANY WAY CNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer s application or use of the Product. At Buyer s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer s application, product or system. Buyer shall take application responsibility in all cases. NEVER THE PRODUCT FOR AN APPLICATI INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMR PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. OMR Corporation Industrial Automation Company In the interest of product improvement, specifications are subject to change without notice. (c)copyright OMR Corporation All Right Reserved.