PD alarm system brings peace of mind in Malta

Transcription

1 (173 words) CASE STUDY - Enemalta How effective is continuous monitoring of Partial Discharge (PD) activity in MV substations? This case study is based on a paper presented jointly by state utility Enemalta and EA Technology at the 2th International Conference on Electricity Distribution (CIRED) in Prague, 29. PD alarm system brings peace of mind in Malta By Stephen Holmes, EA Technology Ltd The state owned utility for Malta, Enemalta, undertakes a broad range of operations including the generation and distribution of electricity. Throughout the years, Enemalta has been instrumental in pioneering the usage of new technology to reach its corporate objectives, whilst at the same time offering better products and services. One such initiative was the adoption of best practice in condition assessment of substations with a particular emphasis on insulation condition and the detection of Partial Discharge (PD) activity at MV. Starting in 25 Enemalta has invested heavily in portable partial discharge detection and location equipment. This investment has paid substantial dividends in improved reliability and safety of personnel visiting substations. Portables vs Monitors At transmission voltages, the importance of continuous monitoring of PD activity in switchgear and other assets has been long recognised [1]. The consequence of asset failure within a transmission network, in terms of customer interruptions and customer minutes lost, can be high. Transmission assets also have a high capital cost, therefore the addition of continuous PD monitoring can be of great value with a relatively small addition to the overall capital cost. At MV, the viability equation changes. Here assets are of lower relative value and the consequences of a failure of a single asset in terms customer minutes lost is generally lower. Portable instruments, therefore, tend to prevail as their cost can be amortised over the whole network of assets. For Enemalta s MV network, it was natural therefore to start with portable instruments. Simple-to-use UltraTEV Detectors were initially issued to each district office and one to the maintenance section. Later, numbers were increased so that each technical officer within the maintenance section had access to an UltraTEV Detector. These devices were primarily issued for staff safety in entering substations or operating switches. They detect PD activity using ultrasonic and Transient Earth Voltage (TEV) [2] sensors to indicate dangerous levels of PD with a red light. Any red light detected would be investigated further by more sophisticated instruments and experienced staff based locally. The use of the instruments was later expanded to cover asset condition assessment. Enemalta subsequently acquired a portable PD Locator to identify the source and magnitude of PD emissions in greater detail, together with additional ultrasonic probes. Since the acquisition of portable PD detection and location equipment, and through the application of a scheduled programme of surveys, Enemalta has detected discharges in 34 cable terminations (mostly heat shrinkable type), 18 switchgear busbar accessories and 11 Ring Main Unit switch or circuit breaker related faults. All these showed a high activity of partial discharge and therefore immediate action was taken to repair or replace the defective components. Had these faults not been detected, Enemalta customers would have experienced power cuts and in some instances insulation breakdown would have led to catastrophic failure of the substation with wider consequences. Figure 1 shows the quantity of PD activities located in various switchgear compartments.

2 Faults detected Figure 1 Enemalta location of recorded PD faults using portable instruments Oil Filled Termination Compound Termination Shrinkable Termination Busbar RMU switch Circuit Breaker Switchgear compartment For the majority of Enemalta substations, the use of portable instruments has proven to cost effective way forward. However, some assets were considered to be critical because: 1) Their continued reliability was key to the stability of a large section of the Enemalta network, supplying substantial numbers of customers with importance to Malta s economy i.e. tourist and industrial areas 2) They were known troublesome assets with a history of problems, but were currently not shortlisted for replacement 3) Intensive but intermittent PD activity had already been detected with portable instruments and a measure of the activity over time was required It was for these reasons that Enemalta decided to install a continuous partial discharge alarm system into its substation at Msierah Distribution Centre, New Hospital Distribution Centre and later at Marsa South Distribution Centre. The chosen system was an UltraTEV Alarm. The installation of this equipment, supported by the PD Locator and additional ultrasonic probes, provided further information about the state of the switchgear where the UltraTEV Alarm was installed. Where previously a snap shot of readings was taken through a scheduled programme, now these substations were being monitored continuously and intermittent partial discharges were detected. Although these results raised concern to the maintenance engineers, they were in a position to further investigate and plan an outage to the affected switchgear, before any partial discharge became continuous or, worse still, the equipment failed. Indeed, through use of the UltraTEV Alarm, the maintenance engineers managed to locate and repair or replace some defective components such as an 11kV voltage transformer, an 11kV circuit breaker, a 33kV single core cable and 11kV busbar. The types of switchgear installed at these substations are: Msierah DC Voltage: 11kV Type: VMXC Manufacturer: GEC ALSTHOM Year: 1995 Insulation: Air insulated busbar Cast resin bushings New Hospital DC Voltage: 33kV Type: HMXS Manufacturer: GEC ALSTHOM Year: 1995

3 Insulation: Air insulated busbar Cast resin bushings Marsa South DC Voltage: 11kV Type: SAFESIX Manufacturer: ABB Year: 1992 Insulation: Air insulated busbar Cast resin bushings PD Activity in a Heat Shrinkable 11kV Termination UltraTEV Alarm system installation Alarm Hub

4 Alarm Node UltraTEV Alarm System Description The system consists of a series of nodes magnetically attached to each switchgear panel in a substation. On the back of the node is the TEV sensor. In addition, each node can be equipped with ultrasonic detection via a magnetically clamped microphone on a flexible stalk. The nodes are daisy chained together with a single wire carrying both signals and power. Each node is capable of recording a Current TEV Alarm and a Current Ultrasonic Alarm. The nodes will show when an alarm has occurred at some point previously via a separate Historic TEV Alarm and Historic Ultrasonic Alarm. The nodes apply a time constant to help prevent spurious noise tripping a Historic Alarm. The Alarm States are communicated back to the Hub unit using the single wire bus. The Hub unit also provides power to the Nodes. The Hub unit provides a contact closure to indicate either a Historic TEV or Ultrasonic alarm. This contact closure can be used to trigger a local visual or audible alarm. Alternatively, the contact closure can be fed into a SCADA system, where this is available. A third option, and the one selected by Enemalta, is to monitor the system for Alarms using a GPRS/iHost system. This enables the Alarm state to be monitored by a web browser. This is a convenient solution for Enemalta and, additionally, allows EA Technology to easily view the results as part of its support for Enemalta. Results Almost immediately after installation of the UltraTEV Alarm, the Msierah substation was indicating abnormal PD activity. These initial results seemed to indicate intermittent PD activity but there was a lingering doubt. The UltraTEV Alarm was a new design and maybe something was not right: perhaps a previously undiscovered error in design or aberration of software. It required verification. To do this, EA Technology supplied and installed in parallel a PD Monitor. The PD Monitor is a 12 channel TEV only monitor with advanced data collection and analysis. It records its data to a local FLASH memory card. Rather than just simple alarms states, it gives great detail on any PD activity and, by the use of precedence between probes [2]; it can assist in the location of TEV activity in the substation. It is an established design with loyal following from engineers, but a considerably more expensive option than the somewhat simpler UltraTEV Alarm. A comparison of the results, over the same time period, of the UltraTEV Alarm and PD Monitor is shown in Figures 2, 3 and 4. Figure 2 shows the PD Activity (Short Term Severity) as recorded on Channel 6 of the PD Monitor Figure 3 shows the PD Activity (Short Term Severity) as recorded on Channel 11 of the PD Monitor Figure 4 show the UltraTEV Alarm state (either OFF or ON) Short Term Severity (STS) is a useful short hand employed by the PD Monitor for expressing PD activity over time. It is defined as: STS = TEV x P

5 Alarm State Severity Severity where TEV P is TEV magnitude in mv is the number of TEV pulses per mains cycle Figure 2 PD Monitor Channel 6 PD Activity /3/28 8/3/28 9/3/28 1/3/28 11/3/28 12/3/28 13/3/28 14/3/28 15/3/28 Time and Date Figure 3 PD Monitor Channel 11 PD Activity /3/28 8/3/28 9/3/28 1/3/28 11/3/28 12/3/28 13/3/28 14/3/28 15/3/28 Time and date Figure 4 UltraTEV Alarm State 3 On 15 Off 7/3/28 8/3/28 9/3/28 1/3/28 11/3/28 12/3/28 13/3/28 14/3/28 15/3/28 Time and Date Conclusion The comparative results showed a very good correlation between the UltraTEV Alarm and the PD Monitor. This gave Enemalta confidence in their new UltraTEV Alarm equipment. The switchgear continues to be monitored by the UltraTEV Alarm with further investigations ordered using portable PD detection equipment on any alarm raised. Faulty components are replaced as soon as a full outage is possible.

6 The two UltraTEV Alarm systems have now picked up critical partial discharge activity in both internal and external components, including cast resin bushes and voltage transformers. All were spotted before they could develop into faults which could lead to failures. The UltraTEV Alarm had proven itself to be a cost effective method of monitoring for MV assets. REFERENCES [1] G. Georghiou; P. Lewin; A. Metaxas, 24, "Guarding your assets", IET, Power Engineer vol. 18 issue 1, P2-22 [2} N.Davies, C.Lowsley 23 The evolution of non-intrusive partial discharge testing of MV switchgear Proceedings CIRED Conference [3] N Davies, J.Tang, P.Shiel, 25, Benefits and experiences of non-intrusive partial discharge measurements on MV switchgear Proceedings CIRED Conference News Update 21 After two years of trials, Enemalta ( has ordered one of the biggest UltraTEV Alarm installations in the world, to protect its network against faults developing into failures. The installation comprises two UltraTEV Alarm systems: one with a total of 268 alarm nodes to protect its distribution network, and one with 52 nodes for its power station. Some units are fixed and some used for mobile troubleshooting where emerging faults are suspected. The nodes are linked to a total of 19 hubs, which are in turn linked by GPRS to an ihost virtual web server. This instantly sends alerts of suspicious PD activity to engineers via SMS and . Enemalta has also invested in a comprehensive package of instruments to investigate PD faults in detail, including an UltraTEV Monitor system, together with UltraTEV Plus and UltraTEV Detector handheld units.