design guide for wireless l i g h t i n g c o n t r o l

Transcription

1 design guide for wireless l i g h t i n g c o n t r o l

2 ON OFF system operation radiotouch Fluorescent Fixtures ( With Lutron dimming ballasts) Power RadioTouch Controller RadioTouch Controller Power Power and Control Fluorescent Fixtures ( With Lutron dimming ballasts) Power RadioTouch Wallbox Transmitter RadioTouch Tabletop Transmitter(s) By simply pressing buttons on a RadioTouch transmitter, radio frequency signals are sent to RadioTouch Controllers housed in the ceiling. These Controllers then send signals to Lutron dimming ballasts adjusting the light levels and also send signals to optional window treatments and projection screens to adjust window treatments or screen levels. Add up to 16 transmitters in the room to meet your flexibility needs RadioTouch tabletop or security mounted 3 One Controller 4 Equip fluorescent lighting fixtures 5 transmitters can with Lutron be placed anywhere 1% Hi-lume, Eco-10 in a room. and TVE 0-10V dimming ballasts. 2 RadioTouch wallbox transmitters can replace any wall switch. is required per lighting zone. The same Controllers are used to control motorized window treatments and projection screens. Lutron dimming ballasts can be installed in existing fixtures or can be ordered pre-installed in a Lutron fixture, and some fixtures by other manufacturers. Call toll-free

3 design steps In All Installations: Select your dimming ballasts, dimmable fixtures or load interface for each lighting zone. See page 8 and Select the appropriate Controller. One per lighting zone (dimming, switching, window treatment/screen control). See page 8 Determine the number and style of wallbox transmitters and wallplates you need. See page 9 Select the wireless tabletop transmitter and mounting method. See pages Select any optional accessories. (occupant sensors, daylight sensors, or rs232 interfaces) See pages Call toll-free

4 examples The following scenario demonstrates a potential RadioTouch solution for the classroom shown: 1. The classroom has nine, 277V, 2 ft. x 4 ft., T8, three lamp fixtures. The customer would like 1% Hi-lume fluorescent dimming for AV presentations. The appropriate ballast model is FDB The room will have front lights and general lights controlled in separate groups. Each group requires an RTA-RX-F Controller. 3. The room requires simple On/Off entrance control for the front and general lights to replace the existing wall switches by the door. Two RTA-WX-2B-WH controls will provide simple control for each group of lights in the room. A two-gang Claro wallplate will provide a clean, screwless look at the wallbox. 4. The presenter would like to have control of each lighting group from the podium. An RTA-TX-2L-B-WH tabletop transmitter provides separate control of two lighting groups, and an RTA-SEC-WH security clip can be added to mount the transmitter to the podium. 5. Determine if the lighting system needs to work with other devices such as occupant sensors, daylight sensors, touchscreens, or window treatments. See pages 8 through 13 to determine the models required for your application. Call toll-free

5 ON OFF ON OFF ON OFF ON OFF This example installation describes what and why RadioTouch is necessary for this classroom. Product Ordered: (9) FDB (2) RTA-RX-F Front Lights (2) RTA-WX-2B-WH (1) CW-2-WH (1) RTA-TX-2L-B-WH (1) RTA-SEC-WH General Lights Call toll-free

6 system overview Wire Type A Distribution Panel (not included) Controller One per lighting zone Wire Type C Tabletop Transmitter* ON OFF Wire Type A Wallbox Transmitter* Transformer plugs into an outlet Wire Type E RS-232 Interface* Wire Type D Touchscreen System Up to 5 dry contact closure inputs (from others) * Up to 16 unique transmitters per Controller. All transmitters must be within 35 feet of the Controller they are controlling. Transformer plugs into an outlet RTA-SCI Contact Closure Interface Wire Type C Daylight Sensor Room Occupancy Sensor Call toll-free

7 wiring type key Type A Type B Type C Type D Type E (2) 12 AWG (120/277V) (3) 12 AWG wires (120/277V) (3) AWG Class 2 wires (4) 18 AWG Class 2 wires Standard RS232 cable Incandescent, magnetic low voltage or electronic low voltage interface Wire Type A or Wire Type B Lutron Dimming Ballast Fluorescent Fixtures (not included) Lutron Dimming Ballast Fluorescent Fixtures (not included) To Additional Lutron Ballasts AC Motorized Window Treatments (Up to 4 per Lutron Group Control. Multiple window treatments require home run wiring to Group Control for each window treatment.) To V Power Source Lutron Group Control Wire Type B or Wire Type A AC Motorized Projection Screen Sivoia QED Contact Closure Interface Lutron Sivoia QED Controllable Window Treatments Call toll-free

8 controllers Controllers for lights, window treatments and projection screens Switches one lighting zone, plus occupant sensing (requires sensor); can be fixture or junction box mounted Regulates one lighting zone, plus occupant and daylight sensing (requires sensor); can be fixture or junction box mounted Regulates one lighting zone, plus occupant and daylight sensing (requires sensor), and switch closure outputs; can be fixture or junction box mounted Includes one RTA-RX-F-SC and one WC-4M-GC for control of AC Motorized Window Treatments and projection screens RTA-RX-SW 1 RTA-RX-F 1 RTA-RX-F-SC 1 RTA-RX-F-SC-ACM One required per lighting zone Accepts inputs from occupant sensors Operates at 120/277 V Switches 16 Amps of high inrush lighting load One required per lighting zone Controls Lutron Hi-lume, co-10, and TVE ballasts directly Controls Lutron Tu-Wire ballasts, incandescent and magnetic/ electronic low voltage sources through an FDI Load Interface Accepts inputs from occupant sensors and a daylight sensor Operates at 120/277 V 16 A continuous dimming capacity All functions of RTA-RX-F plus the features below Controls Sivoia QED Controllable Window Treatments through a SVQ-CCI-8 interface Provides up to five momentary output switch closures to GRAFIK ye products or equipment by others. All functions of RTA-RX-F-SC (except Sivoia QED ) plus the features below Provides group control of up to four AC Motorized Window Treatments Additional motorized window treatments can be controlled by adding more WC-4M-GC or WC-1M-GC group controls load interfaces * *All load interfaces operate at 120 Volts Load interfaces for control of lights, window treatments and projection screens Interfaces for incandescent, magnetic low voltage, electronic low voltage and Lutron Tu-Wire ballasts FDI-INC FDI-ELV FDI-FTU-16A Connects RadioTouch Controller to an incandescent or magnetic low voltage lighting circuit; 2000 W capacity Connects RadioTouch Controller to an electronic low voltage lighting circuit; 1000 VA capacity Connects RadioTouch Controller to one Tu-Wire ballast fluorescent lighting circuit; 16 A capacity Interface to AC Motorized Window Treatments and projection screen motors WC-4M-GC WC-2M-GC Provides individual or master control of one or up to four AC Motorized Window Treatments or projection screens Add to RTA-RX-F-SC-ACM for control of additional AC Motorized Window Treatments Contact Closure Interface to Sivoia QED Controllable Window Treatments SVQ-CCI-8 Provides master control of up to 95 Sivoia QED (Quiet Electronic Drive) Controllable Window Treatments 1 Available in 347 Volt models 2 Backbox mounted (junction box or 2-gang) Call toll-free

9 OPEN ON OFF OPEN STOP CLOSE UP ON OFF DOWN PRESET CLOSE wallbox transmitters * Wallbox transmitters for control of lights On/Off control of one or more switched lighting zones RTA-WX-2BSW-WH 1 *All Wallbox transmitters operate at 120/277 Volts Use in multiples for multi-location switching Can communicate with multiple Controllers for master control of multiple lighting zones On/Off and Raise/Lower control of one or more dimmable lighting zones RTA-WX-2B-WH 1 Use in multiples for multi-location dimming Can communicate with multiple Controllers for master control of multiple lighting zones Four preset levels plus Off and Raise/Lower control of one or more dimmable lighting zones RTA-WX-5B-WH 2 Use in multiples for multi-location control Can communicate with multiple Controllers for master control of multiple lighting zones Wallbox transmitters for control of AC Motorized Window Treatments and projection screens Open/Stop/Close control of one or more AC Window Treatment zones RTA-WX-C3LB-WH 1 Use in multiples for multi-location AC Window Treatments Can communicate with multiple Controllers for master control of AC Window Treatment zones Up/Down control for one or more AC motorized projection screens RTA-WX-C2LB-WH 1 Wallbox transmitters for control of Sivoia QED Controllable Window Treatments Use in multiples for multi-location AC motorized projection screen control Can communicate with multiple Controllers for master control of multiple projection screen zones Open/Preset/Close control of one or more Sivoia QED Controllable Window Treatment zones RTA-WX-Q3LB-WH 1 Use in multiples for multi-location Sivoia QED Window Treatments Can communicate with multiple Controllers for master control of multiple Sivoia QED Window Treatment zones claro wallplates Screwless wallplates for single or multi-gang installations Single-Gang Screwless Wallplate CW-1-WH Two-Gang Screwless Wallplate CW-2-WH Three-Gang Screwless Wallplate CW-3-WH Four-Gang Screwless Wallplate CW-4-WH Contact Lutron Customer Service for wallplate laser-engraving at LUTRON1 For 5- and 6-Gang applications, contact Lutron Customer Service 1 Standard button laser-engraving included on large button transmitters 2 Factory button labels included with slim-button transmitters Call toll-free

10 Lights 3 Lights 3 Lights 3 Lights Lights 3 Lights 3 Lights Lights 3 tabletop transmitters * Transmitters for dimmable lighting zones only *Two AAA batteries and mounting bracket included One dimmable lighting zone Two dimmable lighting zones RTA-TX-L-WH RTA-TX-2L-WH Raise/Lower control of one, two or three zones of lights Four push buttons factory set for high, medium, low, and minimum light levels plus off, as well as continuous dimming control per zone Three dimmable lighting zones RTA-TX-3L-WH One dimmable lighting zone Two dimmable lighting zones RTA-TX-L-B-WH RTA-TX-2L-B-WH Raise/Lower control of one, two or three zones of lights One pair of push buttons per zone for On/Off control of non-dim lighting, as well as continuous dimming control per zone Three dimmable lighting zones RTA-TX-3L-B-WH Transmitters for dimmable and/or On/Off switched lighting zones One dimmable lighting zone and one zone of On/Off lighting control Two dimmable lighting zones and one zone of On/Off lighting control RTA-TX-LSW-B-WH RTA-TX-2LSW-B-WH One pair of push buttons per zone for On/Off control of non-dim lighting One pair of On/Off buttons and one pair of Raise/Lower buttons per dimmable zone for continuous dimming control One dimmable lighting zone and two zones of On/Off lighting control RTA-TX-L2SW-B-WH One zone of On/Off lighting control RTA-TX-SW-B-WH One pair of push buttons per zone for On/Off control of non-dim lighting Two zones of On/Off lighting control RTA-TX-2SW-B-WH Three zones of On/Off lighting control RTA-TX-3SW-B-WH Call toll-free

11 Shades 2 Shades 2 Shades Shades 1 Shades 1 Shades Lights Projection Shades Lights Projection Lights Transmitters for dimmable lighting zones and/or AC Motorized Window Treatments or projection screens One dimmable lighting zone and one pair of output switch closures Two dimmable lighting zones and one pair of output switch closures RTA-TX-LC2-B-WH RTA-TX-2LC2-B-WH One pair of On/Off buttons and one pair of Raise/Lower buttons per dimmable zone for continuous dimming control One pair of push buttons for momentary dry switch closure outputs for control of projection screens or other equipment One dimmable lighting zone and Open/Stop/Close control of one AC Motorized Window Treatments Zone Two dimmable lighting zones and Open/Stop/Close control of one AC Motorized Window Treatments Zone RTA-TX-LC3-B-WH RTA-TX-2LC3-B-WH One dimmable lighting zone RTA-TX-L2C3-B-WH and Open/Stop/Close control of two AC Motorized Window Treatment Zones Lighting control as above Three push buttons for Open/Stop/Close control of AC Motorized Window Treatments Open/Stop/Close control of one AC Motorized Window Treatment Zone RTA-TX-C3-B-WH Three push buttons for Open/Stop/Close control of AC Motorized Window Treatments Open/Stop/Close control of two AC Motorized Window Treatment Zones RTA-TX-2C3-B-WH Call toll-free

12 Projection Shades 2 Shades Shades Shades 1 Lights Lights Shades Shades 2 Lights Shades 1 Lights 3 Shades tabletop transmitters * *Two AAA batteries and mounting bracket included Transmitters for dimmable lighting, Sivoia QED Controllable Window Treatments, and projection screens One Sivoia QED Controllable Window Treatment Zone Two Sivoia QED Controllable Window Treatment Zones RTA-TX-Q-B-WH RTA-TX-2Q-B-WH Three push buttons for Open/Close/ Preset control of Sivoia QED Controllable Window Treatments One dimmable lighting zone and one Sivoia QED Controllable Window Treatment Zone RTA-TX-LQ-B-WH One set of On/Off push buttons and one set of Raise/Lower push buttons per lighting zone for continuous dimming Two dimmable lighting zones and one Sivoia QED Controllable Window Treatment Zone RTA-TX-2LQ-B-WH Three push buttons for Open/Close/Preset control of Sivoia QED Controllable Window Treatments One dimmable lighting zone and two Sivoia QED Controllable Window Treatment Zones RTA-TX-L2Q-B-WH One dimmable lighting zone, one Sivoia QED Controllable Window Treatment Zone and one pair of output switch closures RTA-TX-LQC2-B-WH One set of On/Off push buttons and one set of Raise/Lower push buttons per lighting zone for continuous dimming Three push buttons for Open/Close/Preset control of Sivoia QED Controllable Window Treatments One pair of push buttons for momentary dry switch closure outputs for control of projection screens or other equipment Call toll-free

13 UP Scenes 9-12 Scenes 5-8 Scenes 5-8 Scenes 1-4 Scenes 1-4 Scenes 1-4 Transmitters to activate scenes on a Lutron GRAFIK Eye System Five buttons of output switch closures RTA-TX-C5-WH Five buttons for control of GRAFIK Eye Systems Provides access to four scenes and Off when used with an RTA-RX-F-SC and a GRX-AV or OMX-AV Nine buttons of output switch closures RTA-TX-C5C4-WH Provides eight scenes and Off when used with two RTA-RX-F-SC and two GRX-AV or two OMX-AV 13 buttons of output switch closures RTA-TX-C52C4-WH Provides 12 scenes and Off when used with three RTA-RX-F-SC and three GRX-AV or three OMX-AV Transmitter mounting bracket options Transmitter security mounting bracket RTA-SEC-WH Tamper-resistant bracket secures transmitter to wall, table or other surface Allows transmitter to be removed only for battery replacement Screws and wall anchors included Transmitter mounting bracket Included with each tabletop transmitter Mounts transmitter to wall, table or other surface Transmitter snaps in and out easily Screws and wall anchor included Call toll-free

14 accessories how do i add occupant sensor control? Most 15 and 24 V Occupant Sensors wire directly to any RadioTouch Controller with low voltage, Class 2 wiring for simplified installation Allows you to select Manual On or Automatic On operation Automatically dim or turn Off lights when a room is unoccupied Detect minor motions for example, hand movements of a person seated at a desk or conference room table Occupant Sensor Available Models: To find out about Lutron Occupancy Sensors, see how do i connect to touchscreens? The RadioTouch RS232 interface provides a seamless link between RadioTouch RF Controllers, and RS232 compatible equipment, such as touchscreen systems. Controls up to 10 lighting zones, Sivoia QED Controllable Window Treatments, or contact closure output zones Connects to data link through either a DB-9 plug or terminal blocks Model # RTA-RS232 Operates with a plug-in power supply Can provide feedback to the host device that the RF commands have been sent Operates with 3-wire software flow control or full 7-wire hardware handshaking Call toll-free

15 how do i add daylight sensor control? The MW-PS-WH and MW-FPS-WH daylight sensors wire directly to the RadioTouch Controller with low voltage, Class 2 wiring for simple installation The MW-PS-WH and MW-FPS-WH reduce the available electric light output of the connected RadioTouch Controller, based on the presence of sunlight in the room; in the absence of sunlight the available electric light is increased back to its previous state One MW-PS-WH or MW-FPS-WH is required for each RadioTouch lighting zone that needs to perform daylight harvesting Model # MW-PS-WH Model # MW-FPS-WH what if i want custom labeling? RadioTouch Wallbox and Tabletop Transmitters and Claro Wallplates can be provided with custom laser-engraving. Laser-engraved Claro Wallplates may be added after the system is installed. Tabletop and Wallbox Transmitters must be laserengraved prior to shipment. Contact Lutron Customer Service at lutron1 for laser-engraving forms and quotes. Call toll-free

16 accessories how do i get sivoia QED? For more information on Sivoia QED Controllable Window Treatments or other window treatments please contact: Lutron Shading Solutions at or visit us on the web at how do i use radiotouch to control grafik eye? The RadioTouch Lighting System can be used to control a GRAFIK Eye System using a GRAFIK Eye AV Interface. RadioTouch Transmitters can activate 4, 8, or 12 scenes and Off Requires a GRX-AV or OMX-AV and an RTA-RX-F-SC for each 4 scenes which need to be activated For detailed wiring see the RadioTouch Installation Guide Call toll-free

17 specifications 1. The visual environment control system shall include a microprocessor-based Controller capable of logically integrating radio frequency transmitters, inputs from occupant sensors, and daylight sensors. 2. The Controller shall be able to reliably receive control signals from system transmitters located within a 35 ft. radius of the Controller. 3. The tabletop transmitter shall provide wireless radio frequency control of the Controller from any location in the room within the specified range. 4. Each tabletop transmitter shall include a pressure sensitive label set to identify controlled lights and other functions and shall be manufactured with pockets that accept zone identification labels. 5. The dimmable Controller shall provide a method for adjusting the maximum and minimum light levels. 6. The dimmable Controller shall provide for an emergency override that can bring the lights to the maximum light level. 7. The dimmable Controller shall provide an override switch for 100 continuous hours of full light output for fluorescent lamp burn-in, with automatic return to normal operation. 8. The Controller shall be available in models that can provide five Class 2 momentary dry switch closures. 9. The Controller shall be available in models to control Sivoia QED Controllable Window Treatments. 10. The Controller shall be equipped with Status and Power On LEDs. 11. Each transmitter in the system shall have a unique hard coded address. 12. Each Controller in the system shall have the ability to have 16 unique transmitters addressed to control the Controller. 13. Available transmitter models in the system shall have the ability to be addressed to control any number of Controllers within the specified range. 14. Controllers shall accept RF transmissions from a Lutron RS232 interface, which connects to an RS232 host device. 15. The Lutron RS232 interface shall be capable of controlling 10 unique zones of lights, Sivoia QED Controllable Window Treatments or contact closure outputs. 16. Occupant sensors, daylight sensors and switch closure outputs to other equipment shall use Class 2 wiring that is electrically isolated from line voltage wiring by means of a Class 2 transformer and physical separation. 17. The Controller shall operate at voltages of 120 and 277 or 347 V at 60 Hz. The line voltage wallbox transmitters shall operate at voltages of 120 and 277 V. 18. The Controller shall supply 15 and 24 V for occupant sensor operation, not to exceed 30 ma. 19. The dimmable Controllers shall provide an air-gap off, and be tested to reliably control a 16 A load of Lutron ballasts for an estimated ten year life (30,000 cycles). 20. The switching only controller shall incorporate Lutron Softswitch technology to ensure that no arching will occur at the mechanical contacts when power is applied or removed from the load circuit. This Controller shall be rated for 16 Amps (fully loaded 20 A circuit) for an estimated 10 year life (30,000 cycles) of continuous duty for the following load types: 1. High intensity discharge 3. Magnetic fluorescent ballast 5. Electronic low voltage 7. Neon Cold Cathode 2. Electronic fluorescent ballast 4. Incandescent 6. Magnetic low voltage 21. The Controller and line voltage wallbox transmitters shall pass a 6000 V, 200 A surge test (ANSI 62.41). 22. Operation of the Controller and all transmitters shall be rated for ambient temperatures from 0 to 40 C. 23. The Controller and line voltage wallbox transmitters shall be UL listed industrial controls and CSA approved. 24. All system transmitters shall be FCC and Industry Canada listed and Controllers shall be FCC and Industry Canada compliant. 25. The Controller shall be capable of mounting to a 4 in. x 4 in. junction box or directly to a knockout of a fluorescent fixture. 26. Controls, sensors and ballasts shall be provided by a single manufacturer with a minimum of 25 years electronic fluorescent lighting control experience. 27. Manufacturer shall offer optional custom engraving services for tabletop and wallbox transmitters and Claro Wallplates. 28. The manufacturer shall have ISO 9001 quality registration and have factory employed service engineers. 29. Manufacturer shall test the functionality of each Controller, wallbox transmitter, tabletop transmitter and dimming ballasts, if applicable, prior to shipment. 30. The Controller, wallbox transmitter, tabletop transmitter and dimming ballasts, if applicable, shall be specified Lutron RadioTouch; no equal without written approval prior to bid due date. 31. Manufacturer shall provide a toll-free phone number, with 24-hour, 7-day a week access, to specifically service technical and application questions. Call toll-free

18 Dimensions Dimensions Controllers, RS232 Interface A: 4.00 in. (100 mm) B: 7.75 in. (197 mm) C: 2.50 in. (64 mm) A B C Wallbox Transmitters A: 2.93 in. (74,4 mm) B: 4.69 in. (119,1 mm) C: 0.30 in. (7,5 mm) D: 1.37 in. (34,8 mm) E: 2.75 in. (70,0 mm) ON OFF Dimensions Tabletop Transmitters A: 3.57 in. (90,7 mm) B: 3.23 in. (82,0 mm) C: 0.70 in. (17,8 mm) D: 0.98 in. (24,9 mm) Installer s Guides Installer s Guide RS232 Installation and Protocol Document To download the installation instructions, CSI specification, or the product specification submittal sheets, visit the RadioTouch website at This product may be covered under one or more of the following U.S. patents: 4,835,343; 4,954,768; 5,248,919; 5,399,940; 5,736,965; 5,838,226; 5,848,054; DES 353,798; DES 389,461; DES 389,805; DES 395,037 and corresponding foreign patents. U.S. and foreign patents pending. Lutron, co-10, Hi-lume and Tu-Wire are registered trademarks, Hi-lume Compact, RadioTouch and Sivoia QED are trademarks of Lutron Electronics Co., Inc Lutron Electronics Co., Inc. the leader i n l i g h t i n g c o n t r o l The RadioTouch system is a lighting control innovation from Lutron, the recognized leader in residential and commercial lighting control systems. Lutron is the brand preferred by lighting designers and specifiers worldwide. With over 11,000 products and more than 250 active U.S. patents, Lutron consistently leads the industry with high quality, innovative lighting control solutions. Lutron has offices worldwide and our products can be found in use in over 80 countries. Lutron Electronics Co., Inc Suter Road Coopersburg, Pennsylvania Technical and Sales Assistance, call the toll-free Lutron Technical Support hours/7 days U.S.A. and Canada From other areas, call: or fax: Visit our website at Lutron Electronics Co., Inc. Printed in the U.S.A. 3/07 P/N