AddressPro Digital Dimming Technical Product Information
|
|
- Cory Webb
- 5 years ago
- Views:
Transcription
1 AddressPro Digital Dimming Technical Product Information
2 Installation Guidelines Control Wiring: Additional control wiring is required for AddressPro systems. The control wiring (violet and gray wires) may be configured for Class 1 or Class 2 installations. Install and wire these ballasts and controls in accordance with the National Electrical Code (NEC) as well as all applicable federal, state and local electrical codes. Only qualified personnel should perform installation. Both control leads and power leads (Line, Neutral and Ground) must be connected to each ballast and each wallbox or ceiling mounted control. Only AddressPro controls will work with AddressPro ballasts and modules. Factory Programmed: AddressPro systems are pre-set at the factory to allow for use immediately upon installation with no programming required. The pre-set program configures all of the ballasts to be in Area 1, Zone 1 and has four pre-set scenes ranging from full bright to full dim. Simple programming with the handheld remote (ES5704CTL or ES5705CTL) and any wall box IR receiver is required to assign ballasts to different zones. Basic function programming with ES5704CTL handheld remote and an Infrared (IR) receiver: To Assign Zones: Using the ES5704CTL handheld remote, the digital IDs of the individual ballasts are captured and programmed into one of 12 zones. Zone assignments can easily be changed with the remote. To Control a Zone: The light levels of individual zones can be controlled with programmable remotes or the programmable wallbox control. To Program a Scene: After setting all of the zones at specific light levels, this scene can be saved by using the programmable remotes or wallbox controls. Up to 12 scenes with fade rates can be stored. To Recall a Scene: Simply press and release the scene number (1-12) on the remote or wallbox control. For ballast data, operating instructions for controls, installation guidelines and programming features, consult the Universal Lighting Technologies website at
3 AddressPro Dimming Controls ES5702CTL Handheld 4-Scene Remote ES5703CTL Handheld Programming Remote ES5720CTL Ceiling Mount IR Sensor Kit ES5961CTL Scene Splitter Joins or separates two control loops. ES5901CTL Wall Control Provides on/off and up/down light level adjustment with IR receiver. ES5903CTL Wall Control Provides on/off, up/down light level adjustment and 4-scene recall control with IR receiver. ES5902CTL Wall Control Provides on/off, up/down light level adjustment, 12-scene recall, individual zone control, and scene and fade rate programming with IR receiver. ES5402CTL RS232 Adapter Module
4 AddressPro Troubleshooting Guidelines Additional Troubleshooting Techniques. In some cases, the troubleshooting methods outlined above may not lead to a quick detection and resolution of the problem. In such cases it is often beneficial to perform one or more of the following tasks: Divide and Troubleshoot the System: If a large system of AddressPro ballasts has an apparent malfunction but the specific component or location is unknown, the system can be divided somewhere near the center of the control circuit. If the malfunction persists on one side but not the other, further separations may help determine the actual failure site. Bypass Installed Control Wires: If the source of a malfunction cannot be assigned to a ballast or to the wires connecting it to the control system, disconnect the installed control wiring and connect a good control device using visible, external control wires. Ballast Substitution: After performing all steps mentioned above, if any of the luminaries still do not respond, then replace with a known good unit and try again. Control Substitution: After performing all of these troubleshooting techniques, if none of the lighting devices in the AddressPro loop respond to the control device, replace the control device with a known good unit. For further assistance or ordering information, contact Universal Lighting BALLAST or visit or our website at
5 Wiring Diagrams Case Styles Fixture wiring: Fluorescent fixtures must be equipped with non-shunted sockets that are used with rapid start and programmed start ballasts. Lamp wiring must be per diagrams on ballast labels.
6 AddressPro Digital Dimming Ballasts
7 AddressPro System Features and Components AddressPro is a protocol for the digital communication between the lighting devices. This digital protocol allows simplified control wiring that provides greater flexibility than traditional 0-10V analog systems. FEATURES: Programmable Zones: AddressPro technology allows the user to subdivide the loop into 12 zones (a number of light sources grouped together for simultaneous control) through programming after the system installation. Easy System Setup: All components in an AddressPro loop are connected in parallel to the two control wires. Even though all the ballasts share the same data bus, each individual component can be assigned to the zone of choice. Complete Flexibility: Each light source is shipped from the factory with a 28 bit unique ID. A remote is used to capture the ID of each light source and assign it to a zone. Programmable Scenes: AddressPro allows the user to program up to 12 recallable pre-set lighting scenarios called scenes. Easy System Reconfiguration: The reconfiguration of an existing AddressPro system (changes to the system functioning, scenes, zones the device belongs to, etc.) can be achieved through the programming without any hardware changes. Programmable Fade Time: This is the transition time to obtain the desired scene. Fade time is measured in seconds and is adjustable from 1 sec. to 9999 sec. Dimming Control Range: AddressPro ballasts provide reliable lighting control down to 1% for T5 and 3% for T8 and compact fluorescent lamps. System Size: Up to 250 ballasts and 10 control stations per control loop. Area Subdivision: Each system can be subdivided in up to 12 areas. Each area can then be divided into zones with controls programmed for operating the individual areas. All areas on a system can be globally controlled by a master control. COMPONENTS: AddressPro Ballasts: Universal offers a wide variety of AddressPro ballasts for T5, T8, CFQ and CFT lamps. Features include: - Universal input voltage ( volts) for installation flexibility. - Starts at any level without flashing. - Control input protected against mis-wiring. - Super LampGard lamp end-of-life protection. Wall Controls with IR Receivers: Universal offers three wall controls with features ranging from simple on/off and up/down control to scene programming and recall functions. The wall stations also have an infrared detector for receiving commands from the handheld remote. Handheld Remotes: Universal has three remotes that use infrared communication to perform programming and operation. Dimming Modules: Dimming modules are available for line voltage incandescent and low voltage halogen with either magnetic or electronic transformers. Ceiling Module Controls: Universal offers two ceiling module control units that are housed in a junction box and have a tethered infrared detector to receive commands from the remote. Occupancy Sensor to Dim-D Adapters: These modules translate third party, line-switching occupancy sensor signals into AddressPro commands. Rotary Switch for Joining/Separating Two Control Loops: Our wall-mounted rotary switch divides a large AddressPro control system into two loops. Ceiling Mount IR Receivers: These special ceiling mount IR receivers control the AddressPro components in conjunction with the AddressPro handheld remote.
8 AddressPro Application Examples Lighting levels can be controlled so that the presentation side of the room has either more or less light depending upon the media utilized. Halogen lighting is used to accent pictures or drawing charts mounted on two of the walls. A 4-scene wall control is used at the entrance. The ES5704CTL handheld remote is used for zone programming, as well as for scene programming and recall functions. With 14 lighting sources in this room, most of them can be set as their own zone if desired (up to 12 zones possible). Lighting zones can be set so that during A/V presentations, the lights near the front can be dimmed while lights in the rear can be set at higher levels. A 4-scene handheld remote is used in conjunction with the ceiling IR sensor for dimming control. Controls at the doors provide on/off and up/down control. Programming is done with an ES5704CTL handheld remote, which should be stored separately to prevent unauthorized programming of the lighting. Additional specification information and application notes are available at It s Easy To Reach Us... By mail: Universal Lighting Technologies, Inc. 26 Century Blvd., Suite 500 Nashville, TN Phone: (615) Web site: webmaster@universalballast.com Lit #DIMOV506 All specification information is subject to change without notification Universal Lighting Technologies, Inc.
UNIVERSAL LIGHTING OFFERS BREAKTHROUGHS FOR BOTH ANALOG AND DIGITAL DIMMING APPLICATIONS
UNIVERSAL LIGHTING OFFERS BREAKTHROUGHS FOR BOTH ANALOG AND DIGITAL DIMMING APPLICATIONS SuperDim and AddressPro provide dimming versatility and time-saving convenience SuperDim Analog Dimming Ballasts
More informationUniversal Lighting Technologies is a subsidiary of Panasonic Electric Works Co., Ltd., a member of the Panasonic Group. Technical Product Information
Universal Lighting Technologies is a subsidiary of Panasonic Electric Works Co., Ltd., a member of the Panasonic Group Technical Product Information DCL with DEMANDflex DEMANDflex ballasts are high efficiency
More informationDALI Dimming Controls
DALI Dimming Controls ezdali Fluorescent dimming made simple and affordable A New Digital Revolution ezdali, Watt Stopper s new digital dimming and scene controls, uses the DALI communications protocol
More informationGE Lighting. Lighting Controls. DALI Digital Lighting Controls
GE ighting ighting Controls I Digital ighting Controls the I Protocol Multi-functional control of I-ready GE uminaires 1-1 to I converters available for analogue luminaires I CB Type 2 - complete programmable
More informationDIVISION 26 ELECTRICAL SECTION LIGHTING CONTROL SYSTEM
DIVISION 26 ELECTRICAL SECTION 26 09 26 PART 1 GENERAL 1.01 DESCRIPTION A. The intent of this set of specifications is to provide a complete, functional, intelligent, lowvoltage lighting control system
More informationHigh bay PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
EBDSPIR-HB-DD Product Guide High bay PIR presence detector DALI / DSI dimming Overview The EBDSPIR-HB-DD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional
More informationCeiling PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. PIR Sensor.
Product Guide EBDSM-DD Ceiling PIR presence detector DALI / DSI dimming Overview The EBDSM-DD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationdesign guide for wireless l i g h t i n g c o n t r o l
design guide for wireless l i g h t i n g c o n t r o l ON OFF system operation radiotouch Fluorescent Fixtures ( With Lutron dimming ballasts) Power RadioTouch Controller RadioTouch Controller Power Power
More information, ,
796-2028, 796-2021, 796-2025 Batten mount PIR detectors Overview This series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual control
More informationReduce lighting energy costs with controls
Reduce lighting energy costs with controls Reduce energy costs. Support sustainability Get control of your lighting. Upgrading lighting systems to next-generation lighting technologies can deliver energy
More informationMiro Wireless Dimming and Scene Control Made Elegantly Simple
Miro Wireless Dimming and Scene Control Made Elegantly Simple WIRELESS RF LIGHTING CONTROLS WIRING DEVICES Miro Style Choose from the traditional styling of Miro Decorator (top) or the elegant simplicity
More informationSENSA MRE DDM MR
96239831 SENSA MRE DDM MR Contents Section Contents Page 1 Dimensional information 1 2 Description and operation 2 3 Wiring and fixing 3 4 Programming 6 5 Wiring diagrams 8 6 Detection pattern diagrams
More informationProduct Bulletin for Decora Rocker Slide Controls
Product Bulletin for Decora Rocker Slide Controls Decora Rocker Slide Controls Application Leviton Decora Rocker Slide s provide smooth, slide-action, full-range dimming for incandescent, dimmable LEDs,
More informationApplied Lighting Controls
Better Buildings By Design 2010 Applied Lighting Controls Steven Mesh, LC, IESNA Senior Lighting Program Coordinator Pacific Energy Center (Pacific Gas & Electric) 851 Howard Street, San Francisco, CA
More informationDigital Addressable Lighting Interface
Digital Addressable Lighting Interface Who started DALI? It is supported by major manufacturers of ballasts Initially promoted by: And now including: BAG, Erco, Insta, Johnson controls, Magnetek, FCS lighting,
More informationPIR/INT & PIR/INT-D. Batten mount PIR detectors. Product Guide. Overview. Features
Product Guide PIR/INT & PIR/INT-D Batten mount PIR detectors Overview The PIR/INT & PIR/INT-D miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional
More informationUse this addendum with the LP Installer s Guide to install a. GRAFIK RP System
Attention Installer: Use this addendum with the LP Installer s Guide to install a GRAFIK RP System Wallstation GRAFIK RP A GRAFIK RP System is a combination of up to four Grafik RP Dimming Panels and up
More informationStellar Panelboard Dimming Systems
create a new dimension in lighting control. While lighting systems consume energy, Stellar dimming panels conserve and redirect energy into the atmosphere of your facility. The panel s universal dimmers
More informationIntegrated PIR detectors
EBMINT - Product Guide Integrated PIR detectors Overview The EBMINT series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual control
More informationEBDHS-DD-LT30. Ceiling PIR HS presence detector DALI / DSI, low temperature. Product Guide. Overview. Features
EBDHS-DD-LT30 Product Guide Ceiling PIR HS presence detector DALI / DSI, low temperature Overview The EBDHS-DD-LT30 PIR (passive infrared) presence detector provides automatic control of lighting loads
More informationProduct Guide. Ceiling microwave presence detector DALI / DSI. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MPAD-C-DALI-230V Product Guide Ceiling microwave presence detector DALI / DSI Overview The MPAD-C-DALI-230V microwave presence detector provides automatic control of lighting loads with optional manual
More informationLighting Controls An Introduction and Review
Lighting Controls An Introduction and Review Prepared by Dialectic Controls Beyond Timeclocks and Contactors When designing the lighting for a space, there is always a debate concerning what lighting control
More informationFluid Round Large 700 FMFLDRL_
Installation Instructions for Fluid Round Large 700 FMFLDRL_ 90FLUIDRL.0 CEILING COLLECTION GENERAL PRODUCT I NFORMATION: This product can mount to either a " square electrical box with round plaster ring
More informationProduct Guide. Ceiling PIR HS presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs.
PPAD-C-HB-DALI-230V Product Guide Ceiling PIR HS presence detector DALI / DSI dimming Overview The PPAD-C-HB-DALI-230V PIR (passive infrared) presence detector provides automatic control of lighting loads
More informationTrios Training Manual
Trios Training Manual Version 1.2, June 2002 TRIOS training-manual 1. 2 1 1. TRIOS SYSTEM INTRODUCTION... 2 The Trios Concept... 2 Trios Multi-functionality... 2 Trios Flexibility... 2 Trios Simplicity...
More informationMWS5. Miniature Microwave Presence Detector (standalone) Product Guide. Overview. Features
Product Guide MWS5 Miniature Microwave Presence Detector (standalone) Overview The MWS5 series of miniature microwave presence detectors provide automatic control of lighting loads with optional manual
More informationEBMPIR-MB. Batten mount PIR detectors. Product Guide. Overview. Features
Product Guide EBMPIR-MB Batten mount PIR detectors Overview The EBMPIR-MB series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual
More informationHigh bay PIR presence detector 1-10V dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
Product Guide EBDSPIR-HB-AD High bay PIR presence detector 1-10V dimming Overview The EBDSPIR-HB-AD PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationCRESTRON: GREEN LIGHT NETWORK LIGHTING CONTROLS 1
GREEN LIGHT ARCHITECTURAL DIMMING CONTROLS (GLPD) Crestron Green Light and Green Light Express Network Dimming Control Systems are web accessible, network connected dimming control systems that receive
More informationCeiling PIR HS presence detector 1-10V, low temperature. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
Product Guide EBDHS-AD-LT30 Ceiling PIR HS presence detector 1-10V, low temperature Overview The EBDHS-AD-LT30 PIR (passive infrared) presence detector provides automatic control of lighting loads with
More informationProduct Guide. Ceiling PIR presence detector DALI / DSI dimming. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs.
Product Guide LPCMPIRDSI Ceiling PIR presence detector DALI / DSI dimming Overview The LPCMPIRDSI PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationPassive infrared ceiling sensor
Passive infrared ceiling sensor 88 Description Control and command device, powered by the SCS BUS, with two different sensors, the combination of which enables managing the light level inside the room,
More informationUltraLITE Model ELU Centralized Emergency Lighting Inverter 4.2 KW- 5 KW
12/23/16 Rev 9 UltraLITE Model ELU General Specification 4.2 KW to 5 KW UltraLITE Model ELU Centralized Emergency Lighting Inverter 4.2 KW- 5 KW 1.0 General General Specification This specification describes
More informationB.E.G. LUXOMAT net. KNX intelligent building automation using sensors from B.E.G.
B.E.G. LUXOMAT net KNX intelligent building automation using sensors from B.E.G. Effective energy saving in buildings 2 KNX sensors from B.E.G. are specially developed for the creation of economical solutions
More informationDirect Dim Microwave Presence/Absence Detector
Product Guide MWS3A-DD Direct Dim Microwave Presence/Absence Detector Contents Section Contents Page 1 Dimensional information 1 2 Description and operation 2 3 Wiring & Fixing 3 4 Installation 3 5 Fixing
More information600 Watt Dimmer Install Guide
600 Watt Dimmer Install Guide ER6CD This guide covers all models of the ER6CD lighting controller. The box contents includes the controller with lock nut and installation guide. Overview The ER6CD controller
More informationI-320 SERIES AC EMERGENCY LIGHTING EQUIPMENT
P.O. BOX 84 TUCSON, AZ 85734 (520) 294-3292 FAX (520) 74-2837 www.iotaengineering.com INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be
More informationSWITCHLITE MRE DDM ADJ
96239889 SWITCHLITE MRE DDM ADJ Front features Mounting Bezel Back features Retaining Spring Power Input & Switched Output Connector (Channel 1) Sensor Lens which covers... Microwave Sensor IR Receiver
More informationEBMHS (standard & slim-line PSU)
Product Guide EBMHS (standard & slim-line PSU) Miniature HS PIR Presence Detector (luminaire fitting) Overview The EBMHS series of miniature PIR (passive infrared) presence detectors provide automatic
More informationAdvanced Lighting Control for High Building Performance
www.sylvania.com Advanced Lighting Control for High Building Performance Better Buildings by Design Kandice Castellino February 2014 Burlington, VT Why Advanced Lighting Controls? Controls Greater energy
More informationPRESENCE DETECTOR. PD-C360i/8 mini KNX PD-C360i/12 mini KNX / 13 7 REMOTE CONTROL PRESENCE DETECTOR
In the Master function, the remote control entries will be acknowledged as follows: acknowledged 3 x with the red LED In the Slave function, each detection is acknowledged 2 x with the green LED. NOTE:
More informationImperial War Museum. Case Study 17. clipsal.com UNITED KINGDOM. C-Bus Control and Management System
Imperial War Museum UNITED KINGDOM C-Bus Control and Management System Case Study 17 clipsal.com C-Bus brings Visionary Manchester Landmark to Life The Imperial War Museum North is the first building in
More informationSMART BASIC BASIC-IR DAYLIGHT
LUXMATE Lighting Control System LUXMATE. The ing system for maximum quality and dimming convenience. SMART BASIC BASIC-IR DAYLIGHT The art of modern technology lies in making complicated things simple.
More informationVive PowPak Fixture Controls
Vive 369918g 1 03.12.18 The PowPak wireless fixture control is a radio-frequency (RF) device that controls either the Lutron EcoSystem or 0 10 V- electronic fluorescent ballasts and LED drivers (depending
More informationAN INTRODUCTION TO DIGITAL ADDRESSABLE LIGHTING INTERFACE (DALI) SYSTEMS & STUDY OF A DALI DAYLIGHTING APPLICATION LISA MEYER
AN INTRODUCTION TO DIGITAL ADDRESSABLE LIGHTING INTERFACE (DALI) SYSTEMS & STUDY OF A DALI DAYLIGHTING APPLICATION by LISA MEYER B.S., Kansas State University, 2007 A REPORT submitted in partial fulfillment
More informationConnections, displays and operating elements C D E G H. Installing the control unit
1 2 3 GB Control unit 0-10 V REG-K/3-gang with manual mode Operating instructions Art. no. MTN646991 ¼ DANGER Risk of fatal injury from electrical current. All work on the device should only be carried
More informationUP 258E11 OPTISENS OFFICE
Product and functional description The UP 258E11 is a presence/motion detector with integrated 2-point light control. The UP 258E11 device communicates via KNX/EIB with actuators or other KNX devices.
More information11,1 30. Ordering data
ID Compact control module with ambient light sensor and motion sensor Compact dimensions for luminaire installation For up to 10 DSI or I ballasts I/DSI output channels with adjustable negative offset
More informationF series. echoflex. Slim Line Dimming Controller. Product Overview ER1S-FC
echoflex Powered by ETC ER1S-FC Slim Line Dimming Controller F series This guide covers the F series of the Complete Room Controller, model number ER1S-FCU equipped with a 902 MHz radio. The box contents
More informationProduct Guide. Ceiling microwave presence detector DALI / DSI. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MPAD-C-A-DALI-230V Product Guide Ceiling microwave presence detector DALI / DSI Overview The MPAD-C-A-DALI-230V microwave presence detector provides automatic control of lighting loads with optional manual
More informationMODEL RLY-DIM-D INSTALLATION INSTRUCTIONS
MODEL RLY-DIM-D INSTALLATION INSTRUCTIONS IMPORTANT SAFEFGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED. THESE INCLUDE: READ AND FOLLOW ALL SAFETY INSTRUCTIONS
More informationProduct and Applications Description
Product and Applications Description The presence detector with a sensing range of 360 allows the automatic execution of control functions in the electrical system by detecting movements. For example,
More informationLighting and Fan Speed Controls
Lighting and Fan Speed ontrols Smart Dimmer System -1 Decorator Touch Dimmers -2 Decorator Slide Dimmers -3 Rotary Dimmers -4 Rotary Dimmers Replacement Knobs -5 Toggle Dimmers -6 Architectural Dimmers
More informationDual Technology Wall Mounted Occupancy Sensor. Manual & Specification
Dual Technology Wall Mounted Occupancy Sensor Manual & Specification PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH LOCAL ELECTRICAL CODES Douglas Lighting Controls Page 1 December 16, 2013 1. INTRODUCTION
More informationPRODUCT DATA AND INSTALLATION SHEET MWS5-SA STAND ALONE MINIATURE CEILING MOUNTED MICROWAVE PRESENCE DETECTOR
8. SPECIFICATION LOAD 6 Amps fluorescent and incandescent lighting. 3 Amps compact fluorescent lighting. 3 Amps low energy lighting. 3 Amps low voltage lighting (switch primary of transformer). Switch
More informationAnalogue Dimming Microwave Presence/Absence Detector
Product Guide MWS3A-AD Analogue Dimming Microwave Presence/Absence Detector Contents Section Contents Page 1 Dimensional information 1 2 Description and operation 2 3 Wiring & Fixing 3 4 Installation 3
More informationF series. Complete Room Controller. echoflex Powered by ETC. Product Overview ERDRC-FC
echoflex Powered by ETC Complete Room Controller F series ERDRC-FC This guide covers the F series of the Complete Room Controller, model number ERDRC-FCU equipped with a 902 MHz radio. The box contents
More informationluxcontrol lighting control system basicdim basicdim ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor
ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor Product description Compact dimensions for luminaire installation For up to 10 DSI or LI devices (max. 5 per output channel)
More informationIllumaTech Innovations
IllumaTech Innovations An Innovative New Family of Smooth, Slide Bar and Rotary Decora-Style Dimmers and Fan Speed Controls with Preset and Non-Preset Models IllumaTech Innovations Innovative lighting
More informationLoop out. Ambient daylight threshold
transmitter 0 ULT - HC9V Type of Product: Description: Finish: Warranty: Tri-level Dimming Control Microwave Motion Sensor Colour White years Daylight threshold Stand-by period Stand-by dimming level Antenna
More informationLPC3BSP65 & LPC3BDP65
Product Guide LPC3BSP65 & LPC3BDP65 Batten mount PIR detectors Overview The LPC3B series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional
More informationApplication Note. Using XPoint Wireless Devices with Emergency Lighting. 1 of 16
Using XPoint Wireless Devices with Emergency Lighting 1 of 16 Table of Contents Introduction...3 Application Summary...3 UL924 Standard Summary...4 ER Option - Normal Power Sensing Leads...4 ER Intended
More informationluxcontrol lighting control system basicdim basicdim ILD Compact control module with ambient light sensor and motion sensor
ILD Compact control module with ambient light sensor and motion sensor Compact dimensions for luminaire installation For up to 10 DSI or DALI devices (max. 5 per output channel) 2 DALI/DSI output channels
More informationModel 4880 Status Output Display Module Manual
Model 4880 Status Output Display Module Manual 1-2 150912 Section 1 Introduction The 4880 provides 16 switched outputs, 4 form C relay contacts, and an X10 module interface. See Table 2-1 for electrical
More informationDIMAX DIMAX 534 plus D GB F I E nl. Installation and operating instructions Universal dimmer. DIMAX 534 plus
310455 01 DIMAX DIMAX 534 plus 5340001 A1 A2 GB Installation and operating instructions Universal dimmer DIMAX 534 plus D GB F I E n B1 N DIMAX 534 plus Contents Basic safety instructions 3 Designated
More informationCeiling Microwave presence detector - DALI / DSI 12-24V AC/DC. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MWS6-DD-LV Product Guide Ceiling Microwave presence detector - DALI / DSI 12-24V AC/DC Overview The MWS6-DD-LV microwave presence detector provides automatic control of lighting loads with optional manual
More informationSECTION 26 NX DISTRIBUTED INTELLIGENCE LIGHTING CONTROL SYSTEM HUBBELL CONTROL SOLUTIONS
SECTION 26 NX DISTRIBUTED INTELLIGENCE LIGHTING CONTROL SYSTEM HUBBELL CONTROL SOLUTIONS PART - 1 GENERAL 1 SYSTEM DESCRIPTION A. The distributed lighting control system as specified herein shall be comprised
More information11,9. Ordering data. Max. cable length sensor head 1 basicdim ILD lx 150 lx m 1
Compact dimensions for luminaire installation For up to 10 DSI or DALI devices (max. 5 per output channel) DALI/DSI output channels with adjustable negative offset from channel to channel 1 Ambient light
More informationMotion Sensor. For Outdoor Use. Wall & ceiling mounted. Quick & Easy Installation 2 Channels
MS3602CH 2 Channel Motion Sensor For Outdoor Use Wall & Ceiling Mounted Quick & Easy Installation 2 Channels Channel 2 Distance Wiring Diagram 220-240V ~ 50Hz 14A Max. (cosø=1) 3000W for incandescent load
More informationOperation Manual Model: Light Switch Combo Universal Dimmer Module Item No.: WMR-252. Specification. Wiring
Operation Manual Model: Light Switch Combo Universal Dimmer Module Item No.: WMR-252 Featuring an unique universal wireless dimmer module receiver that allows remote controlling existing house hold dimmable
More informationRelated Sections: TBD. Effective Date: January 1, 2016
Description: The purpose of the section is to highlight the current applicable UMCP Design Standards for the design, selection and, installation of lighting fixtures within buildings. Related Sections:
More informationC-Bus Application Note. Function Rooms and Ballrooms. Overview
C-Bus Application Note Function Rooms and Ballrooms Overview A function venue or hotel will generally include large spaces purpose designed and built for holding functions. Function rooms and Ballrooms
More informationSPECIFICATION SUBMITTAL
SPECIFICATION SUBMITTAL The dimmer with remote control One tap on to selected light level/off; two taps full bright;press & hold for 10-second fade-tooff Press rocker to adjust light level Front accessible
More informationLPCMPIRM65 & LPCMPIRDSI65
Product Guide LPCMPIRM65 & LPCMPIRDSI65 Luminaire high mount PIR detectors Overview The LPCMPIR PIR (passive infrared) presence detector provides automatic control of lighting loads with optional manual
More informationFCCP 200: Fume-cupboard indicator and monitor
Product data sheet 3.1 43.170 FCCP 200: Fume-cupboard indicator and monitor How energy efficiency is improved Display and interface for safe, energy-efficient monitoring of fume cupboards, pressure zones
More informationC. The system shall be capable of turning luminaires on/off (where supported by the luminaire) as well as full range dimming.
SECTION 260943 SPECIFICATIONS - Wireless Network Lighting Controls. PART 1 - GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY AND KEY SYSTEM DIFFERENTIATORS A. The lighting control system specified herein shall
More informationRadioRA 2 PRELIMINARY COPY 68 F 70 F. Wall-mounted seetemp display for temperature control Coming soon!
Away, 8:00 AM First Floor Current Temperature Second Floor Current Temperature RadioRA 2 Wall-mounted seetemp display for temperature control Coming soon! Lutron ipad app for total home control Coming
More informationCeiling PIR HS presence detector. Product Guide. Overview. Features
Product Guide 796-2047 Ceiling PIR HS presence detector Overview The 796-2047 (passive infrared) presence detector provides automatic control of lighting loads with optional manual control. This is a high
More informationController - 4 x 1-10 V outputs - BUS/KNX
87045 LIMOGES Cedex France Telephone: (+33) 05 55 06 87 87 - Fax: (+33) 05 55 06 88 88 Controller - 4 x 1-10 V outputs - Page 1. Use...1. Technical features...1 3. Dimensions.... 4. Connection... 5. Installation...3
More informationTABLE OF CONTENTS. 1. Intelligent Light 1.1 Intelligent Corridor Light 1.2 Intelligent Down Light
Tanda Technology (Hong Kong) Limited is a member of Tanda Group of Shenzhen, China. Tanda Group specializes in the design, manufacturing and sales of the Intelligent Fire Alarm System (IFAS), Intelligent
More informationFixture Controller. Applications. Features. Specifications. Certifications & Affiliations. Catalog #: ALC/ALCE Part #: /
Project name Prepared by Date INDOOR AIRLINK LUTRON Catalog #: ALC/ALCE Part #: 624087/634480 The ALC/ALCE wireless fixture controller is a radio-frequency (RF) device that controls the 0 10V or Lutron
More informationGI1DPC/B User Guide. Mains tungsten GLS filament or halogen lamp Min 60W Max 300W. Linear fluorescent
GI1DPC/B User Guide Single gang PIR Dimmer Replaces a standard light switch or dimmer Turns off automatically Turns on automatically Security mode Night light mode* Scene setting and soft on/off* * only
More informationGetting Started with
Getting Started with Contents Programming Garage Door Openers and Gates...2 Precautions...2 Programming...2 Rolling Code Programming...2 Canadian Programming/Gate Programming...3 Operating the HomeLink
More informationUSER MANUAL INSTALLATION GUIDE FOR: 2X2: MLFP22DS4035 MLFP22DS4041 MLFP22DS4050
DIRECT LIT LED FLAT PANEL: SAVER SERIES USER MANUAL by INSTALLATION GUIDE FOR: 1X4: MLFP14DS4035 MLFP14DS4041 MLFP14DS4050 2X2: MLFP22DS4035 MLFP22DS4041 MLFP22DS4050 2X4: MLFP24DS4235 MLFP24DS4241 MLFP24DS4250
More informationTebis application software
5 Tebis application software STCC530E 2-channel presence detector 360 A faire Product reference Description TP device RF devices TCC530E Bi-zone presence detector TCC530E Output module: Dimmer Loads connected
More informationDALI MSensor 02 Multi-sensor for DALI system
MSensor 02 Multi-sensor for system Component of the comfortdim system ( standalone) With ambient light dependent control and motion detection Simple group assignment via rotary switch Multiple MSensors
More informationCeiling Microwave presence detector - DALI / DSI 12-24V AC/DC. Microwave Sensor. IR Receiver. Light Level Sensor. Status LEDs.
MWS3A-DD-LV Product Guide Ceiling Microwave presence detector - DALI / DSI 12-24V AC/DC Overview The MWS3A-DD-LV microwave presence detector provides automatic control of lighting loads with optional manual
More informationGetting Started with
Getting Started with Contents Programming Garage Door Openers and Gates... 2 Precautions... 2 Programming... 2 Rolling Code Programming... 2 Canadian Programming/Gate Programming... 3 Operating the HomeLink
More informationSECTION LIGHTING CONTROLS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 09 23 LIGHTING CONTROLS SPEC WRITER NOTE: 1. Delete between //----// if not applicable to project. Also, delete any other item or paragraph not applicable to
More informationRetrofit Solutions NEW. Energy-saving products for single rooms. Lutron energy-saving products. Patient Rooms. Office Spaces. Affordable Solutions
Lutron energy-saving products NEW Patient Rooms Office Spaces Educational Facilities Affordable Solutions New Wireless Products Energy Savings Government & Military Retrofit Solutions Energy-saving products
More informationArchitectures for LonWorks Home Automation Systems Luca Coppadoro Echelon
Architectures for LonWorks Home Automation Systems Luca Coppadoro Echelon 04H1122 size Home Automation Market 2001 years 2 2006? TODAY TIME 2002 2003 2004 New Landscape 3 LONWORKS is now accepted as an
More informationEcoSystem H-Series 347 V~ Ballast Overview
Fluorescent Dimming s EcoSystemR H-Series 347 V ~ Architectural Dimming EcoSystem H-Series 347 V~ Overview 369-352e 1 06.04.12 EcoSystem H-Series digitally addressable ballasts provide a low-cost, flexible
More informationIntegrated Classroom Control System. Installation and Operation Manual
Integrated Classroom Control System Installation and Operation Manual 1 Table of Contents Introduction... 3 Installation... 4 Operation... 8 Notes: Daylighting Configuration... 14 Appendix A Open Loop
More informationOperation Manual Fighter ProVision Software. Version: 0.0 Revision: 1
Operation Manual Fighter ProVision Software Version: 0.0 Revision: 1 TABLE OF CONTENTS 1. Introduction 5 2. Software Installation 5 3. PC Users 6 3.1 Introduction 6 3.2 Default Code 6 3.3 Edit PC User
More informationRevolutionise your smart home at the touch of a button...
Revolutionise your smart home at the touch of a button... Deta Connect offers a range of intelligent Lighting, Power and Heating controls with an App for smart control. Suited with Deta s Ultra Screwless
More informationDimming expertise LED UNIVERSAL ROTARY DIMMER
Dimming expertise Whether rotating or pressing LED UNIVERSAL TOUCH DIMMER Future-proof, energy-saving dimming can be so simple with the elegant LED universal rotary dimmers and touch dimmers. Intuitive
More informationDALI SPECIFICATION GUIDE
DALI SPECIFICATION GUIDE Page 2/3 contents Page 1. INTRODUCTION 6 2. DALI - THE STANDARD 6 2.1. Industry standard 6 2.2. Light control 6 2.3. Digital control 7 2.4. Switching in the electronic ballast
More information2012 Toolbar & NH3 Operators Manual
2012 Toolbar & NH3 Operators Manual P/N 320379 Amity Technology, LLC 2800 7th Avenue North Fargo, ND 58102 (701) 232-4199 www.amitytech.com This Page Left Intentionally Blank Page 2 2012 Toolbar/NH3 Manual
More informationOPERATING INSTRUCTIONS
4 START-UP All parameter settings are carried out via the ETS (Engineering Tool Software). The magnet provided can be used to activate the programming status for the physical address on the PD-ATMO 360i/8
More information