PUBLIC SAFETY & SECURITY BUILDING BUILDING RENOVATION & EXPANSION - AUBURN, ALABAMA. Refer to drawing sheet M0.1 and replace with the attached M0.1.

Transcription

1 Date: 30 January 07 To: ll Plan Holders Subject: DDENDUM NO. 3 Project: PULIC SFETY & SECURITY UILDING UILDING RENOVTION & EPNSION - UURN, LM Job #: C# U# 6-9 SSL# 606 From: Raleigh Price The plans and Specifications of the subject project, dated December 4, 06 are amended as follows: (Where there are conflicts between the plans and specifications and the addendum, this addendum shall govern) Item No. : Item No. : The bid date has been rescheduled for February 4, 07 at UFM uilding in Training Room at 3:00pm CST Refer to drawing sheet M0. and replace with the attached M0.. Item No. 3: Refer to drawing sheet P0. and replace with the attached P0. Item No. 4: Refer to drawing sheet E8. and replace with the attached E8. Item No. 5: Item No. 6: Item No. 7: Refer to specifications. dd the attached section Raceways and Wiring. Refer to specifications section rea of Refuge Communication System and replace with the attached section Refer to specifications section Security Camera System and replace with the attached section ttachments: M0. P0. E Raceways and Wiring rea of Refuge Communications System Security Camera System End of ddendum #3

2 Facilities Management 6 West Samford venue uburn University, L Phone: (334) Fax: (344) Safety is our first priority. Think Safety. ct Safely No. Revision Date ddendum No. ddendum No. 3 Project Number#606 Public Safety uilding U 6-9 LEGEND & SCHEDULES - MECHNICL DRWN Y: MJL CHECKED Y: JTS DTE: 0/30/07 FILE NUMER: SS&L 606 PROJECT NUMER: U 6-9 SHEET NUMER: M0. 65 of 94

3 Facilities Management 6 West Samford venue uburn University, L Phone: (334) Fax: (344) Safety is our first priority. Think Safety. ct Safely No. Revision Date ddendum No. ddendum No. 3 ddendum No. 3 Project Number#606 Public Safety uilding U 6-9 LEGEND, SCHEDULES, & DETILS - PLUMING DRWN Y: MJL CHECKED Y: JTS DTE: 0/30/07 FILE NUMER: SS&L 606 PROJECT NUMER: U 6-9 SHEET NUMER: P0. 7 of 94

4 C D E G LIGHTING PLN GENERL NOTES (apply to this sheet only):. FOR EISTING LIGHT FITURES TO E REMOVED, CONTTOR SHLL COORDINTE IN DVNCE THE PROPER MNGEMENT OF LIGHT FITURES WITH TOM HODGES, UURN UNIVERSITY RISK MNGEMENT ND SFETY.. REFER TO HITECTURL CEILING PLN FOR ECT CEILING TYPE ND HEIGHT. UURN 3 4 FUTURE 3 DMIN SERGENT 5 PTROL LIEUTENNT 7 DETECTIVE SUITE E PTROL SUITE INTERVIEW 09 E WOMENS LOCKER 34 MEN'S LOCKER 33 PP E JNITOR 3 E L-4 E J WOMEN'S RESTROOM 34 J DMINISTRTIVE LIEUTENNT 7 PTROL SERGENT 05 J E CE 4 OR E E E PP PP E E CC D EE FF NORTH E-9 (PRTIL) 3 CE PTROL SERGENT 03 MEN'S RESTROOM 33 OFFICE HOTEL 3 SSOCITE DIRECTOR 3 C C 3 L-3 CIULTION CE C C OR 4 E SECURITY SUPERVISOR 5 SSISTNT CHIEF 39 VESTIULE 0 DISPTCHER 54 CE 3 E-9 (PRTIL) LOY 0 RECEPTION 58 E CMPUS SFETY OFFICER 6 DMINISTRTION SSISTNT 46 E CLERY 43 First Floor Plan - Lighting /8" = '-0" 3 L-37 VICTIM ROOM 53 CMPUS SFETY OFFICER 60 E L-39 E FMILY RESTROOM 55 HOUSEKEEPING 5 REK ROOM 63 J FUTURE SHRED 3&4 6 L-35 J L-9 3 E E DIRECTOR/CLERY COMPLINCE 45 EMERGENCY OPERTIONS CENTER/ TRINING ROOM 8 EECUTIVE SSISTNT 66 EECUTIVE DIRECTOR 68 E IT OFFICE 69 4 OR z TRINING EM MNGER & TECH 6 EMERGENCY MNGER 76 EMERGENCY PLNNER FUTURE 7 E-5 L E E E E 9 z E E E E-7 CONFERENCE ROOM 73 G CMER STTION 84 STORGE 85 E- E G G G G SPRINKLER/ WTER RISER ROOM 89 8 UNISE RESTROOM 8 COMMUNICTIONS 8 MECHNICL 90 4 OR 3 E 7 W 7 W 7 W 7 3. ELECTRICL CONTTOR SHLL PROVIDE ND INSTLL TRIM ND MOUNTING HRDWRE FOR ECH LIGHTING FITURE TO MTCH CEILING IN OR ON WHICH IT IS INSTLLED. 4. ELECTRICL CONTTOR SHLL MTCH VOLTGE OF LL FITURES TO THE CIUIT WHICH THEY RE CIUITED. 5. LL SURFCE MOUNTED CONDUIT INSTLLED ON CEILING SHLL E RUN PERPENDICULR ND PRLLEL TO STRUCTURE ND IN MNNER THT IS NET ND SECURE. 6. SITE MEETING SHLL E CONDUCTED ETWEEN THE ELECTRICL CONTTOR, ELECTRICL ENGINEER ND THE HITECT TO DISCUSS ND PPROVE LL EPED CONDUIT RUNS PRIOR TO INSTLLTION OF EPED CONDUITS. 7. LL EPED CONDUIT RUNS SHLL E PINTED S DIRECTED Y HITECT. 8. LL LIGHTING FITURE HEIGHTS LISTED RE MESURED TO THE OTTOM OF THE FITURE FROM FINISHED FLOOR UNLESS OTHERWISE NOTED. 9. PROVIDE ND INSTLL LL CONTROL WIRING ND POWER PCKS S REQUIRED TO OPERTE OCCUPNCY SENSORS. 0. LL EIT SIGNS RE TYPE "" ND "" UNLESS NOTED OTHERWISE.. ROUTE UNSWITCHED HOT CONDUCTORS FEEDING EMERGENCY TTERY PCKS, EMERGENCY EGRESS FITURES ND EIT SIGNS ROUND LIGHTING CONTROL RELYS ND SWITCHES.. ROUTE #6WG MINIMUM LOW VOLTGE CONDUCTORS FROM FITURES WITH 0-0V DIMMING DRIVERS INDICTED IN LIGHTING FITURE SCHEDULE. CONNECT 0-0V CONTROL WIRING TO ECH LIGHT IN CIUIT INDICTED ND CONNECT TO DRIVER. 3. UNLESS OTHERWISE NOTED, LL SINGLE-POLE SWITCHES INDICTED TO INTERFCE WITH ROOM CONTROLLER SHLL E LOW VOLTGE SWITCH, 4-UTTON (LL ON, RISE, LOWER, LL OFF). LIGHTING PLN keynotes (apply to this sheet only): night light FITURE TO REMIN ON 4/7, CONTTOR SHLL CONNECT TO UN-SWITCHED 'HOT' IN LIGHTING CIUIT. EMERGENCY EGRESS LIGHTING FITURE, CONTTOR SHLL CONNECT SWITCHED 'HOT' TO NORML LLST ND UN-SWTICHED 'HOT' TO EMERGENCY TTERY PCK FOR CHRGING ND CONTROL SO THT IN THE EVENT POWER IS LT FITURE WILL TURN ON FOR EMERGENCY EGRESS LIGHTING. ROUTE CIUIT THROUGH LIGHTING CONTROL PNEL. CONTTOR SHLL ROUTE UN-SWITCHED 'HOT' ROUND LIGHTING CONTROL PNEL FOR NIGHT LIGHTING CONTROL. CONTTOR SHLL PROVIDE OVERRIDE SWITCH FOR LIGHTING CONTROL SYSTEM, SWITCH SHLL TURN LIGHTS ON/OFF DURING NORML USINESS HOURS ND OPERTE S ND OVERRIDE SWITCH FTER USINESS HOURS. REFER TO LIGHTING CONTROL PNEL FOR DDITIONL CONTROL REQUIREMENTS. CIUIT TO E ROUTED TO TTERY INVERTER FOR -HOUR OPERTION IN THE EVENT OF LS OF NORML POWER ND GENERTOR CKUP. FITURE TO E NORMLLY CONTROLLED WITH THE OTHER FITURES IN THE ROOM. PROVIDE ND INSTLL ODINE D TRNSFER SWITCH FOR TRNSFER OF LIGHTING DURING EMERGENCY LS OF POWER. PROVIDE SENSING CIUIT TO D. CONNECT LL TYPE 'W' ETERIOR EGRESS WLL PCKS TO CIUIT 'E- 9' FOR ETERIOR LIGHTING. PROVIDE ND INSTLL NEW LIGHTING CONTROL RELY PNEL "LCP". SEE SHEET E. FOR DDITIONL INFORMTION. two-zone room controller to control lighting in training room. zone (z) to be controlled separately from zone (z). provide and install 6-button wallstation to function as follows: - all on - Zone On/off - zone on/off - raise all - lower all - all off UNIVERSITY Facilities Management 6 West Samford venue uburn University, L Phone: (334) Fax: (344) Safety is our first priority. Think Safety. ct Safely No. Revision Date 3 ddendum 3 /30/07 0/8/07 Project Number#606 Public Safety and Security uilding - uilding Renovation & Expansion U 6-9 LINE VOLTGE ND 0-0V 4 OR W 7 inv- S S S 5 ELECTRICL 9 E-3 G 3 E-5 W FIRST FLOOR PLN - LIGHTING DRWN Y: TS LINE VOLTGE ND 0-0V line voltage power source S 0-0V TYPICL ROOM CONTROLLER WIRING DETIL NOT TO SCLE S S S CHECKED Y: KL DTE: 0/4/07 FILE NUMER: SS&L 606 PROJECT NUMER: U 6-9 SHEET NUMER: E8. 89 of 94

5

6 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set SECTION EWYS ND WIRING 600 VOLT PRT - GENERL. SUMMRY. Provide all raceways and wiring specified herein and as required to provide a complete system throughout the project as indicated on the Drawings. PRT - PRODUCTS. CONDUIT. Galvanized Rigid Steel Conduit (G): Rigid steel conduit shall be galvanized, constructed of high-grade raw steel piping, galvanized inside and outside with threaded joints.. Intermediate Metal Conduit (IMC): IMC shall be constructed of high-grade steel tubing, galvanized inside and outside with threaded joints. Zinc coating shall be applied by the hot-dip, galvanized process. C. Electrical Metallic Tubing (EMT): EMT shall be constructed of high-grade steel, zinc coated and galvanized inside and outside. D. Rigid Plastic Conduit (PVC): PVC conduit shall be polyvinyl chloride rigid scheduled to heavy wall type. PVC conduit shall be joined with PVC couplings of the solvent cement type to provide complete watertight joints. Conduit systems shall be UL listed for direct burial and exposed use. E. Flexible Metal Conduit: Shall be flexible steel conduit tubing spirally wound having a hot-dip galvanized coating and meeting requirements of UL for flexible metal conduit. F. Liquid tight Flexible Metal Conduit: Shall be flexible steel conduit spirally wound and shall have a copper grounding strand and factory-applied neoprene jacket. Liquid tight flexible conduit shall meet the requirements of UL. G. PVC coated galvanized rigid conduit: Shall be UL listed. The PVC coating must have been approved by UL as providing the primary corrosion protection for the rigid conduit. The PVC coated conduit must be ETL Verified to the Intertek ETL SEMKO High Temperature HO PVC Coating dhesion Test Procedure for 00 hours. The PVC coated conduit must bare the ETL Verified PVC-00 label to signify compliance to the adhesion performance standard. Ferrous fittings for general service locations must be UL Listed with PVC as the primary corrosion protection. Hazardous location fittings, prior to the plastic coating must be UL Listed. ll conduit and fittings must be new, and unused material. pplicable UL standards may include: UL6 Standard for Safety. Rigid Metal Conduit, UL54 Standard for Safety, Fittings for Conduit and Outlet oxes. Conduit and Fittings shall be evaluated for reliability and performance. Certified test results and the respective test data that have been witnessed and certified to be accurate by an independent, recognized third party. Public Safety & Security ldg EWYS ND WIRING uilding Renovation & Expansion 600 VOLT

7 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set. CONDUIT FITTINGS. G and IMC: shall be factory-made taper threaded and of the same material as the conduit. Provide with molded nylon insulating bushing or throat at all boxes and cabinets with locknuts inside and outside. Provide watertight hubs in wet locations for terminations into enclosures. Provide insulated grounding bushing where required.. EMT: shall be of the same material as the conduit and shall be hexnut compression or steel setscrew. Provide with molded nylon insulating bushing or throat at all boxes and cabinets. Provided insulated grounding bushing where required. C. PVC: shall be Schedule 40 and of the same manufacturer as the conduit. D. Flexible Metal Conduit and Liquidtight Flexible Metal Conduit: Provide couplings at connections between flexible and rigid conduit suitable for that application. Provide with nylon-insulated busing or throat at all boxes and cabinets with locknuts. E. Expansion Joints: Provide O.Z./Gedney, Type expansion joint fittings for all conduit which crosses an expansion joint. Provide with internal ground and external bonding jumper. F. Wire Support ushings: Provide for vertical runs as required by the NEC..3 JUNCTION OES ND PULL OES. Junction boxes and Pull boxes shall be galvanized steel with mode size and gauge as required by the NEC in accordance with voltage parameters. Covers shall be of the same gauge as the box as shall be screw fastened. oxes shall be sized as required but no smaller than 4 inches square and -/ inches deep.. Covers shall be accessible. C. Provide galvanized cast iron or aluminum with threaded hubs and gaskets for outdoor and damp locations. D. oxes in grade or underwater shall be cast brass or bronze..4 OUTLET OES. Outlet boxes shall be UL listed, and of sizes and types required for the application.. oxes Recessed in Construction: Sheet steel boxes, unless noted or required otherwise. oxes shall be no lighter than 4 gauge and shall be galvanized after fabrication. Set so face of box will finish flush with building surface.. For Lighting Fixture Outlets: 4-inch square with raided fixture ring.. For Wall Switches, Receptacles, and Communication Use: 4 inch square, onepiece; no sectional boxes permitted. Use boxes with plaster rings in all plastered walls where wall thickness permits. Use boxes less than -/ inch deep only in locations where deep boxes cannot be accommodated by construction. Public Safety & Security ldg EWYS ND WIRING uilding Renovation & Expansion 600 VOLT

8 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set C. oxes Used Outdoors or in Damp/Wet Locations: Cast metal boxes (iron and alloy) with gasketed covers and threaded hubs. D. oxes in Hazardous reas: pproved cast metal boxes with appropriate sealing fittings. E. Provide blank cover for boxes without fixture or device. F. oxes in grade or underwater shall be cast brass or bronze. G. Cycolac: Per code for pools and fountains only..5 WIREWYS ND UILLRY GUTTERS. Wireways shall be constructed in accordance with UL 870. Every component including lengths, connectors, and fittings shall be UL listed and labeled. Provision shall be included in the construction to allow screwing the hinged cover closed without the use of parts other than the standard lengths, fittings, and connectors. It shall also be possible to seal the cover in the closed position with a sealing wire.. Wireways shall be constructed with/without knockouts, as required. Enclosure type shall be as required by conditions encountered. C. Gutters and Wireways shall be suitable for lay-in conductors. Connector covers shall be permanently attached so that removal is not necessary to utilize the lay-in feature. D. ll sheet metal parts shall be provided with a rust-inhibiting phosphatizing coating and gray baked enamel finish. ll hardware shall be plated to prevent corrosion. ll screws installed toward the inside shall be protected by spring nuts or otherwise guarded to prevent wire insulation damage. E. ll connectors shall be slip-in type with self-retaining mounting screws. ll hangers shall be two-piece with hook-together feature to permit pre-assembly of wireway and hanger bottom plate before hanging on pre-installed upper bracket..6 SURFCE METL EWY. Surface metal raceway shall be UL listed and labeled; shall be used together with couplings, clips, bushings, straps, connectors, connection covers, elbows, extension boxes, fixture boxes, extension adapters, blank covers and all other required fittings; shall be of the proper size to accommodate the conductors to be installed therein in each case..7 CONDUCTORS 600 VOLTS OR LESS. Provide conductors of stranded copper, 98% conductivity, new building wire, insulated in accordance with the requirements of the NEC. Insulation shall be rated no less than 600- volt. Conductors shall be Type THHN, THHW or HHW. Conductors for service and distribution feeders shall be HHW. Solid conductors terminating in a breaker or device shall be utilized for wire size No. and No. 0. Sizes specified are WG gauge for No. 4/0 and smaller and circular mils (kcmil) for sizes larger than No. 4/0. Minimum wire size shall be No.. Public Safety & Security ldg EWYS ND WIRING uilding Renovation & Expansion 600 VOLT

9 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set. Connectors: Make spices and connections in conductors using UL connectors.. Stranded Conductors: UL listed, solderless, bolted pressure or compression connectors. Connectors shall be of proper sizes to match conductor sizes.. Solid Conductors: UL listed, bolted pressure or spring connectors. Connectors shall be of proper sizes to match conductor sizes. 3. Motor Lead Pigtails: UL listed, crimp lugs with through-bolt fasteners between lugs. Lugs shall be of proper sizes to match conductors. Proper sized dies and tools shall be provided to apply connectors. 4. Lighting Fixture Taps: Electrical spring connectors as specified for solid conductors. 5. Ground connections: urndy ground clamps or connectors of a type suitable for and having a UL listing for grounding applications. C. ll conductor sizes shown on the Drawings are copper unless specifically noted otherwise. ll ground conductors shall be copper..8 MNUFCTURERS. Conduit (G, IMC, EMT). llied. Republic 3. Triangle 4. Wheatland. Conduit Fittings (G, IMC, EMT). ppleton. O.Z. Gedney 3. Steel City 4. Thomas and etts 5. Raco C. Flexible Metal Conduit. FC. lflex 3. naconda 4. International Metal Hose D. Liquidtight Flexible Metal Conduit. merican rass Company. naconda 3. Electri-Flex Company E. PVC Conduit and Fittings. Thomas & etts. Prime Conduit 3. Cantex 4. Certainteed 5. Triangle Public Safety & Security ldg EWYS ND WIRING uilding Renovation & Expansion 600 VOLT

10 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set F. Conductors, Copper, 600 Volts or less. merican Insulated Wire. Cablec 3. General Cable 4. Pirelli 5. Southwire 6. Triangle 7. Drakar (Fire Resitive Cables) or UL approved equal G. Conductors, luminum, 600 volt or less (where specified). lcan Cable. Cablec 3. Southwire H. Outlets and oxes. ppleton. Raco 3. Steel City 4. Midland PRT 3 - EECUTION 3. CONDUIT. PVC (encased in 4 concrete on all sides) or Galvanized Rigid Steel (G) meeting corrosion resistant protection of NEC shall be used for underground service entrance and underground feeders. When PVC is used, a transition to metal conduit shall be made below grade using G 90 degree fitting such that only metal conduit exits concrete or ground.. G or Intermediate Metal Conduit (IMC) shall be used where exposed and subject to physical damage, or installed in damp or wet locations. C. Rigid Plastic Conduit (PVC) shall be used for underground branch circuits, underground feeders where run below the slab on grade, maximum in the slab on grade, maximum in the slabs above grade, in concrete columns and concrete wall and in masonry walls. D. PVC Schedule 80 (or G meeting corrosion resistant protection of NEC 300.6) may be used for direct burial for branch circuits only. When PVC is used, a transition to metal conduit shall be made below grade using G 90 degree fitting such that only metal conduit exits concrete or ground. E. Electrical Metalic Tubing (EMT) shall be used for branch circuits concealed in walls and ceilings. EMT may be used for feeders where not exposed to damage and/or not installed in wet or damp locations. F. Flexible Metal Conduit shall be used for connections to rotating or vibrating equipment. The lengths shall be as short as possible, in no case longer than 6 or shorter than. Public Safety & Security ldg EWYS ND WIRING uilding Renovation & Expansion 600 VOLT

11 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set G. Liquidtight Flexible Metal Conduit shall be used for connections to rotating or vibrating equipment where located outdoors or in damp or wet locations. The lengths shall be as short as possible but in no case longer than 6 or shorter than. Liquidtight Flexible Metal Conduit shall NOT be located above a ceiling, in an air shaft or in a mechanical room utilized as a return air plenum. H. Raceways shall be installed as a complete and total wiring enclosure system from outlet to outlet, to junction box, pull box, panel or cabinet prior to the installation of the conductors. I. ll conduit shall be run concealed (except in electrical, mechanical and similar area) unless shown otherwise. Where conduit is run exposed it shall be run in a neat and orderly manner. ll conduit shall be run parallel and perpendicular to the building structure. J. Conduits shall be secured to all boxes, cabinets, panels and equipment with locknuts and bushings and shall be securely fastened in place on intervals required by the Code and local codes; hangers, supports or fastenings shall be provided at each elbow and at the end of each straight run within 3 of a termination to a box or cabinet. ll supports shall be independent and shall not use ceiling supporting system wires. K. Use threaded rods and hangers for supporting single conduit. Multiple conduits shall be supported using a trapeze of Unistrut (or Kindorf) channels and threaded rods with double nut/washer. L. Provide pullboxes as shown and/or as required by Code and where necessary in the raceway system to avoid excessive runs or too many bends. oxes shall have removable hinged or screw covers and shall be accessible. M. The minimum size conduit shall be ¾ diameter. N. Provide non-hardening elastic type duct seal compound for each conduit entering the building from the outside and from one space to another having a normal operating temperature differential greater or less than 0 degrees F. O. Provide seals around all conduit and sleeves penetrating through walls, partition or ceilings. Provide UL approved fire resistant seal around all penetrations through fire rated barriers to maintain the barrier rating. P. Provide pull wire or nylon rope in all empty conduits. Q. ll fire alarm cables shall be run in conduit. Conduit shall be painted red every 0 o.c. (at couplings), at elbows and all backboxes. R. Sleeves shall be rigid G with bushings. S. ll wiring shall be in conduit except telecommunications where cable trays or hooks/rings are provided above suspended accessible ceilings. Public Safety & Security ldg EWYS ND WIRING uilding Renovation & Expansion 600 VOLT

12 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set 3. CONDUIT PROTECTION. Provide underground conduit with a top cover at least 30 below finished grade and no more than CONDUCTORS 600 VOLTS OR LESS. No conductor shall be smaller than No. except for signal or control circuits.. ll conductors shall be installed in conduit. C. Where feeders or circuits are required to be fire protected by NEC rticles 57, 695, 700, 708 and 760 as well as NFP 7, NFP 0, NFP 30 ND NFP 50 they shall be installed either: ) Outside the building and protected as defined by Code; ) Encased in a minimum in of concrete; 3) e protected by a fire-rated assembly to achieve a minimum fire rating of hours and dedicated to the equipment served; 4) e a listed electrical circuit protective system with a minimum -hour fire rating. Feeders for life safety distribution systems under NEC rticle 700 where routed in sprinkler protected spaces are considered to be protected. D. Where a connection is made to any terminal of 40 amperes or more and/or conductors No. 8 or larger, copper terminal lugs shall be bolted to the conductors. Where multiple terminal lugs are made, individual lugs for each conductor shall be used. Where aluminum conductors are accepted in this Section or noted on the drawings, the terminations shall be made with high compression lugs as manufactured by Ideal or MC. E. maximum of six (6) current carrying conductors shall be run in a conduit. The neutral shall be considered a current carrying conductor. F. For homeruns of 0 Volt, 0 amp circuits, where the length of run from the panelboard to the center of the load exceeds 00-0 the conductors shall be No. 0 minimum. If that length exceeds 00-0 the conductors shall be No. 8 minimum. G. For homeruns of 77 Volt, 0 amp circuits where the length of run from the panelboard to the center of the load exceeds 00-0 the conductors shall be No. 0 minimum. H. Multiple branch circuits homeruns serving computer loads, electronic lighting ballasts and/or H.I.D. lighting ballasts shall utilize a neutral conductor one trade size larger than the phase conductors or use separate neutrals for each circuit. Neutral conductors for individual branch circuits may be the same size as the phase conductor but not less. I. Provide an equipment grounding conductor in all feeder and branch circuit conduits. Size per code unless shown otherwise. J. Conductors shall have color coded jackets the entire length. Colors shall be as follows: Public Safety & Security ldg EWYS ND WIRING uilding Renovation & Expansion 600 VOLT

13 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set 0/08 Volt System 77/480 Volt System Phase lack Phase rown Phase Red Phase Orange Phase C lue Phase C Yellow Feeder or Shared Neutral Feeder or Shared Neutral- White Gray ranch Phase Neutral ranch Phase Neutral White w/ lack Stripe White w/ rown Stripe ranch Phase Neutral ranch Phase Neutral White w/ Red Stripe White w/ Orange Stripe ranch Phase C Neutral ranch Phase C Neutral White w/ lue Stripe White w/ Yellow Stripe Ground - Green Ground - Green K. efore pulling any wire into conduit, thoroughly swab the conduit and clean the boxes of debris. L. Run feeders in continuous lengths, without joints or splices. Joints shall occur in branch circuits only in locations where they divide. M. Run conductors for emergency power in conduits separate from all other wiring. N. undle conductors in switchboards and panelboard cabinets and similar using nylon straps made for the purpose. Conductors No. 8 and larger shall be bundled in individual circuits. 3.4 JUNCTION OES, PULL OES, ND OUTLET OES. ll junction boxes and pullboxes shall be sized in accordance with the Code.. ll boxes shall be rigidly secured in position to building structure. oxes larger than 4 shall be secured at two points. C. Outlet boxes shall be flush with the finished wall or ceiling, or not more than ¼ back, unless specifically shown as surface mounted or its purpose is to be above the ceiling. D. Provide galvanized steel or cast type outlet boxes. Where exposed G or IMC terminates in a box, provide cast box with threaded hubs. E. ll boxes shall be provided with a cover plate. F. ll outlet boxes shall be mounted vertically unless noted otherwise. G. Where outlets are shown at the same location but at different heights, they shall be mounted one above the other along the same centerline. H. The exact mounting height of an outlet may be adjusted slightly to align with masonry joint where approved by the rchitect. I. Verify outlet locations in finished spaces with Drawings of interior details and finishes. Public Safety & Security ldg EWYS ND WIRING uilding Renovation & Expansion 600 VOLT

14 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set J. Outlets shall NOT be located back to back. Where outlets are shown on opposite sides of a wall, they shall be located in separate stud spaces. K. Protect floor boxes from entering debris during construction using temporary covers approved by the floor box manufacturer. L. Provide barriers in outlet boxes for switches separating different phases for voltages exceeding 50 volts to ground. M. oxes shall not be supported from a suspended ceiling. N. ll fire alarm back boxes shall be painted red. O. Electrical boxes (stainless-steel/outdoor rated) for irrigation control to be mounted on the building (3-ft FG) with power outlet and control; all holes to be in the bottom of the box. END OF SECTION Public Safety & Security ldg EWYS ND WIRING uilding Renovation & Expansion 600 VOLT

15

16 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set.3 Processors. Processors shall have the following features:.4 Manufacturer. 0 V C system controller.. 0 min. UPS back-up.. Talk--Phone, Command Station CU-8R, or Remote Station ETP-00. PRT 3 - EECUTION 3. Command Stations. Coordinate the location with the rchitect. Install command station in a flush-mounted box, at the location indicated on the Drawings.. Program the system at the command station to indicate the remote stations as alphanumeric description of their location, i.e. Third Floor East Stairwell. C. Program the system at the command station to forward unanswered calls to the telephone number provided by the owner. D. Install a ¾ homerun conduit from command station to each remote station. E. Install one shielded twisted pair copper circuit (not to exceed 5 ohms resistance) from command station to each remote station via the homerun conduit. 3. Remote Stations. Install remote station in surface-mounted boxes at location where the device is indicated on the Drawings to be installed in a -hour or greater fire wall.. Install remote stations in flush-mounted boxes at locations where the device is indicated on the Drawings to be installed in a wall of less than -hour construction. END OF SECTION Public Safety & Security ldg RE OF REFUGE uilding Renovation & Expansion COMMUNICTIONS SYSTEM

17

18 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set G. Refer to the design drawings for camera locations. The existence of drawings does not relieve the contractor of the responsibility of a site survey to confirm the accuracy of the drawings. Specific mounting locations, exact wire and cable runs, and conduit routing have not been specified or delineated on the security device drawings. Coordinate all aspects of the work with the University. I. The contractor shall visit the site and fully investigate all conditions affecting the scope of the work. Failure to visit the site shall not relieve the contractor from any responsibility in the performance of this scope of work..3 SYSTEM DESCRIPTION. The basis of design is the Genetec OmniCast Enterprise software, xis cameras and all related infrastructure and hardware as indicated herein and on the supplied drawings. ll equipment must be 00% compatible with the existing uburn University security system network.. The contractor shall verify all requirements of the existing switch and power locations to assist in the installation and programming of the specified camera and its location..4 CODES ND STNDRDS. The camera shall be installed in accordance with all applicable national, state and local codes including, but not limited to, the most recent editions (as adopted) of the following:. ICSI 569 standard wiring practices. National Electrical Code rticles 300, 700, and National Fire Protection ssociation Life Safety Code (NFP 0) 4. uilding Officials & Code dministrators International, Inc. (OC) 5. Underwriters Laboratories (UL 94, 076, 037) 6. International uilding Code (IC) PRT - PRODUCTS. CMER SECURITY SYSTEM. The closed-circuit television (CCTV) camera system be an extension of the existing Genetec OmniCast Enterprise version Video Management system.. Cameras shall be used to view specific areas inside and outside the premises. The cameras to be utilized shall be an integrated color camera, lens, and mini-dome enclosure system approved for indoor or outdoor applications. The device will operate on VDC or 4VC, utilize NTSCPL or EICCIR camera formats. The unit can be installed on a wall or ceiling, surface-mounted or pendant-style.. CCTV CMERS. ll CCTV cameras furnished on this project shall be of one manufacturer from the approved list as follows: Public Safety & Security ldg SECURITY CMER uilding Renovation & Expansion SYSTEM

19 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set xis, Pelco, or osch.. Fixed dome cameras shall be equal to IS P33 Series with SVG resolution up to 5 megapixel, and including support for SMPTE standard-compliant HDTV 70p and 080p video. The 5 megapixel models shall be able to cover a large area with exceptional detail and light sensitivity. PRT 3 - EECUTION 3. GENERL INSTLLTION. Install systems in accordance with UL, NEC and all other applicable codes. Install system to comply with drawings and final shop drawings in compliance with manufacturer instructions. Provide all required hardware and labor for rack mounting of head-end system components.. Refer to plans for locations and quantities of equipment. Equipment locations shown on plans will be required to be field coordinated to ensure proper system operation. C. No items of equipment shall be installed in such a manner as to void or reduce the proper operating characteristics of individual components or of the system. D. Perform all work under the onsite supervision of a factory authorized trained technician. E. It shall be the responsibility of the technician to check, inspect and adjust this installation to the University approval. trained representative of the installing contractor or manufacturer shall train the University's personnel on the proper operation and maintenance of the equipment. Perform all work in conjunction with this installation in accordance with good engineering practices as established by NEC. 3.0 WIRING INSTLLTION. ll wiring shall be run per University standards. Where existing cable management systems are in place and there is adequate capacity to install the wiring, the contractor may utilize these pathways providing they have coordinated with all other wiring contractor on site.. Where pathways do not exist for wiring, the contractor shall be responsible for providing all required cable management systems such as J-hooks to support communications cabling to meet building codes and manufacturer's recommendations. C. ll cabling installed in ceiling spaces that are used for air distribution plenums shall be UL plenum rated. D. This contract shall be responsible for furnishing and installing all required cabling between components to form a complete and operational system meeting all the requirements of this specifications. 3.3 GROUNDING Public Safety & Security ldg SECURITY CMER uilding Renovation & Expansion SYSTEM

20 Public Safety & Security ldg SS&L Project No.: 606 December 4, 06 uilding Renovation & Expansion U No.:6-9 id Set. The installing contractor shall be responsible for ensuring the grounding integrity of all installed equipment to eliminate the potential for equipment or personnel hazards due to improperly or inadequately grounded systems.. ll grounding and bonding shall be in conformance with the National Electric Code, article 50 and as recommended by EI TI IDENTIFICTION/LELING 3.5 TESTING. Contractor shall identify all major items of equipment and tag all cables with permanent type markers to denote equipment served. Cables shall be tagged at both ends and at each point where the cable is administered. ll labeling shall be approved by the University prior to application.. The University will test each camera. The contractor shall coordinate with the University to provide personnel, equipment, instrumentation, and supplies necessary to troubleshoot any issues that arise with the camera connectivity (cabling) or the cameras, including aiming cameras or adjusting varifocal lenses to achieve the coverage desired by the University. 3.6 WRRNTY. Warranty all cameras and materials for a period of year from the date of Final acceptance from the University. If any defects in materials, workmanship or operational failures under NORML" conditions are experienced within the warranty period, promptly correct at no expense to the University. Provide statement of warranty with operations and maintenance manuals. 3.7 OPERTIONS ND MINTENNCE MNULS. Provide maintenance manuals for every item of equipment when available from the manufacturer. These shall be the technical manuals provided by the manufacturer and shall not consist of generic sales brochures. Technical manuals shall provide complete specifications for the equipment as well as complete operating, maintenance, troubleshooting and product repair replacement information. Where available only in electronic format, the contractor may provide a CD with electronic versions of the manuals.. s uilt drawings updated shall be provided to the university with final as-built information. This shall be in the form of a complete set of Technology drawings with as-built information indicated in colored pen based upon actual field conditions. C. Rack elevations for all systems with rack mounted equipment. G. Warranty: provide statement of warranty with operation and maintenance manuals. END OF SECTION Public Safety & Security ldg SECURITY CMER uilding Renovation & Expansion SYSTEM