Flipper Fidelity FF STN 8 WM Speaker Installation Instructions(03/14/16)
|
|
- Noah Booth
- 5 years ago
- Views:
Transcription
1 Flipper Fidelity FF STN 8 WM Speaker Installation Instructions(03/14/16) Thank you for purchasing the Flipper Fidelity speaker kit for a Stern Pinball machine. This system fits all Whitestar and Sam machines. Your kit includes the following: (1) 8 Woofer with Crossover (2) 4 Speakers with wiring harness and integrated spacers (8) 1 Hex Screws (used with wood speaker panels) (4) ½ #8 Standoffs (used for Star Trek Pro) (8) 5/8 #6 Standoffs (used for Metal Speaker Panels) (1) 4 pin to 2 pin adaptor (inset photo) (1) Volume Control Assembly (2) ½ #6 Wood Screws (2) Insulated crimp on spade connectors Please make sure all parts are present before starting your installation. Tools required for kit installation: 1/4 nut driver. 5/16 nut driver. 11/32 nut driver. Wire terminal crimping tool w/ wire cutter. Note: Use of a drill driver or powered screwdriver is not recommended. Avoid over tightening. The fasteners used by Stern, and those included in this kit, need only be tightened enough to hold the component in place and prevent vibration when in use. Please allow approximately 30 minutes to install. This kit requires no permanent modification to the machine. You may want to take photos of your particular machine in the event you wish to accurately restore it to its original configuration. Step One Machine Preparation. Make sure you have adequate space available to access the front and both sides of the machine. Make sure the machine is turned off and unplugged from its power source. To install this kit you will need to remove the translite to access the back box speakers, speaker connections, and to mount the volume control. Woofer installation requires access to the inside of the base cabinet. If you are not familiar with the procedures to access these areas, i.e. removal of the translite, removal of the playfield glass, and raising the playfield to the service position; please refer to the Stern owners manual. Step Two Disconnect the Back Box speaker Wiring. First, remove the translite. For safety, I would find a towel to drape across the machine for the speaker/display panel to rest on. This will protect both your speaker/display panel and the side rails from getting scratched. Lay the panel on its front, spanning across the side rails. See photo. Carefully examine the existing installation of the back box speakers. The flat wires going to the fasteners holding the existing back box speakers are ground straps which must be replaced when the new speakers are installed. Also not the two types of speaker connections shown in the pictures. This system includes wiring to connect to either type.
2 Step Three A Removal of the Back Box Speakers for Wood Speaker Panels. You will need a ¼ nut driver for speaker removal. Both speakers are attached to each other so be careful not to let one fall. This could result in damage to the machine. Remove all hex screws from each speaker. I find it is easier to do the right one first, place this speaker in the back box, then remove the left speaker. Once all 8 screws are removed, carefully remove the speakers and set aside. There are two ground wires attached to the speakers and speaker grills. Don t lose track of them, as they will need to be re attached in the next step. Step Three B Removal of the Back Box Speakers for Metal Speaker Panels. You will need a ¼ nut driver for speaker removal. Both speakers are attached to each other so be careful not to let one fall. This could result in damage to the machine. There are four 11/32 nuts, two for each speaker. Remove all four nuts and set aside, as you will need these later. Once the nuts are removed, lift the speakers off the studs and set aside. I find it is easier to do the right one first, place this speaker in the back box, then remove the left speaker. There is one ground wire attached to the right speaker, remember to re connect it when you place the new speakers in position.
3 Step Four A Installation of the back box speakers for Wood Speaker Panels. Included in this kit are (8) #8 1 screws, and (8) 5/8 nylon spacers. You will need them for this step. Attach the wiring harness to one of the 4 speakers, connecting the blue spade connectors; the wide connector to the wide terminal (also marked ), the narrow connector to the narrow terminal (also marked + ). Then, place this speaker (with the wires attached) to the right of the display. The wires and speaker terminals will be closest to the back box. Attach to the panel using the new screws supplied. Be careful when lining this all up, and do not forget the ground wire. It is not hard to grab the wrong hole in the speaker grill. Take your time. Attach the remaining speaker, in the same manner, to the left of the display. Run the wire with the pink spade connectors from the right speaker to the left speaker and, following the same convention, carefully push them on to their corresponding speaker terminals. If you purchase a Volume Control Delete speaker system, connect the new speaker harness to the 2 pin connector where you disconnected the factory speakers, and you are done with the back box speakers. Proceed to step 5, the removal of the cabinet speaker. Step Four B Installation of the back box speakers for Metal Speaker Panel. Included in this kit are (8) #8 1 screws. You will need them for this step. Attach the wiring harness to one of the 4 speakers, connecting the blue spade connectors; the wide connector to the wide terminal (also marked ), the narrow connector to the narrow terminal (also marked + ). Then, place this speaker (with the wires attached) to the right of the display. The wires and speaker terminals will be closest to the back box. Attach to the panel using the new screws supplied. Be careful when lining this all up, and do not forget the ground wire. It is not hard to grab the wrong hole in the speaker grill. Take your time. Attach the remaining speaker, in the same manner, to the left of the display. Run the wire with the pink spade connectors from the right speaker to the left speaker and, following the same convention, carefully push them on to their corresponding speaker terminals. If you purchase a Volume Control Delete speaker system, connect the new speaker harness to the 2 pin connector where you disconnected the factory speakers, and you are done with the back box speakers. Proceed to step 5, the removal of the cabinet speaker.
4 Step Four Volume Control Installation. Mounting the Volume Control Several options exist for mounting the volume control. The volume control is attached to a metal L bracket with two small holes on the side. You can mount the volume control using the two ½ #6 screws provided. The screws will fit snugly into the holes and can easily be driven in by hand with a ¼ nut driver. The volume control assembly can be screwed in anywhere on the right side of the back box. I like to attach it very low, just behind the speaker panel. This gives enough room to add a Flipper Fidelity LED Panel. Here you can see the volume control mounted to the back box speaker panel using one of the LED display panel mounting screws.
5 The volume control can be conveniently mounted to the inside of the coindoor with the addition of the Flipper Fidelity Stern Volume Control Coindoor Relocation Kit. Contact Flipper Fidelity for kit details and pricing. Connecting the Volume Control. There are two wires coming off the volume control. One is 2 shorter than the other. The shorter wire has a z clip attached to it. This shorter wire connects to the connector coming off your new back box speakers. The longer wire connects to the lead coming off the board. (This is where you disconnected the stock speakers and inserted the 4 pin to two pin adaptor.) Step Five Removal of the base cabinet speaker. Locate the speaker in the base of the cabinet by raising the playfield to the service position. Cut the wires going to the existing woofer. You will want to cut them as close to the speaker terminals as possible. Using a 5/16 nut driver, remove all four nuts holding the speaker in place and remove the speaker. Place the speaker aside as you no longer will be using this. Keep the nuts as you need these in the next step.
6 Step Six Installing the woofer. Your new woofer will fit right on to the four studs to which the factory speaker was mounted. Proceed carefully. It is possible to damage the speaker cone or surround if not properly aligned when lowering the speaker over these studs. I like to have the x over to the left of the speaker as shown below. Use the four factory nuts to secure the new woofer. Crimp the female spade terminals onto the existing speaker wire. The wire with the white stripe connects to the neg terminal on the woofer. Here is where you have a choice. The new woofer has two positive terminals. The high is the standard input. It in no way affects the output of the woofer. The low reduces the woofer output by about 4db, a minor reduction, but a reduction. This is a way to further tune the sound to your liking. Try the high setting first, then try the low. Leave it where you like it best. Step Seven Adjust the volume control. This will be done to taste. Remember, the volume control you just installed affects only the back box speakers. The machine volume control affects all speakers, thus it can be thought of as a master volume control. I suggest setting the machine volume somewhere between 45 and 54, depending on desired impact. Then adjust the back box speaker volume to obtain a good overall balance. Thank you for your purchase. If needed contact me at: Michael Pupo mpupo@comcast.net
Flipper Fidelity FF STN 10 WM Flippin Fantastic Big Ten Inch Stern Speaker Installation Instructions(03/14/16)
Flipper Fidelity FF STN 10 WM Flippin Fantastic Big Ten Inch Stern Speaker Installation Instructions(03/14/16) Thank you for purchasing the Flipper Fidelity speaker kit for a Stern Pinball machine. This
More informationFlipper Fidelity Stern FF-STN-SPK-8-W Speaker Installation Instructions
Flipper Fidelity Stern FF-STN-SPK-8-W Speaker Installation Instructions Thank you for purchasing the Flipper Fidelity speaker kit for a Stern Pinball machine. Your kit includes the following: (1) 8 Woofer
More informationFlipper Fidelity FF SPK CX CV Coax Speaker Installation Instructions ( )
Flipper Fidelity FF SPK CX CV Coax Speaker Installation Instructions (03 05 2019) Thank you for purchasing the Flipper Fidelity speaker kit for a Stern Pinball machine. Your kit includes the following:
More informationFlipper Fidelity Williams / Bally WPC 95 Installation Instructions
Flipper Fidelity Williams / Bally WPC 95 Installation Instructions Thank you for purchasing the Flipper Fidelity speaker kit for a Williams / Bally WPC 95 Pinball machine. Your system should include the
More informationInstallation Guide for Stern SPIKE 2 Speaker Light Kits
Installation Guide for Stern SPIKE 2 Speaker Light Kits Cover Page / Table of Contents: Warning...02 Before You Begin...02 Tools Needed...03 Installation...04 Wire Connections...08 Remote Usage and DIY
More informationAmber In-wall & In-ceiling Speakers. P/Ns 24431, 24432, 24433, 24434, User's Manual
Amber In-wall & In-ceiling Speakers P/Ns 24431, 24432, 24433, 24434, 24435 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 FEATURES... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS...
More informationAria Polypropylene In-wall & In-ceiling Speakers. P/Ns 18586, 18587, 18588, 18589, User's Manual
Aria Polypropylene In-wall & In-ceiling Speakers P/Ns 18586, 18587, 18588, 18589, 18590 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 FEATURES... 4 CUSTOMER SERVICE... 4
More informationAlpha In-Wall Speaker 10-Inch Carbon Fiber 300W Subwoofer
Alpha In-Wall Speaker 10-Inch Carbon Fiber 300W Subwoofer P/N 30487 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 FEATURES... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS...
More informationAVENGER HT THERMOSTAT RETROFIT INSTRUCTIONS
AVENGER HT THERMOSTAT RETROFIT INSTRUCTIONS In this installation manual: You will remove the existing mechanical thermostat from the Avenger HT dishwasher and will replace it with a new solid state thermostat.
More informationCaliber In-Wall 10-inch Fiber Subwoofer
Caliber In-Wall 10-inch Fiber Subwoofer P/N 30486 User's Manual SAFETY WARNINGS AND GUIDELINES This speaker is intended for indoor use only. Do not expose this speaker to water or moisture of any kind.
More informationC4 ASSEMBLY INSTRUCTIONS
C4 ASSEMBLY INSTRUCTIONS Designed and manufactured in Australia by The Loudspeaker Kit (ABN 39 118 869 962) www.theloudspeakerkit.com 11 Websters Road, Templestowe, Victora 3106 Tel: (03) 9036 2896 Email:
More informationInstallation. Leveling
Your refrigerator was packed carefully for shipment. Remove and discard shelf packaging and tape. Do not remove the serial plate. Location Do not install refrigerator near oven, radiator or other heat
More informationowner s manual 5.25-inch (130 mm) 2-Way Component System
owner s manual 5.25-inch (130 mm) 2-Way Component System Thank you for choosing a JL Audio Evolution C2 Component System for your automotive sound system. These Evolution Speakers have been designed and
More informationEverbrite LCD OrderRite Order Confirmation System
Everbrite LCD OrderRite Order Confirmation System Version 4.X and 5.X Monolith Electronics Insert Replacement Procedures 3/7/2013 NOTE: Do NOT cut any wires except where directed to do so. Failure to comply
More informationEW25 EW30 EW35 USER & INSTALLATION MANUAL. Model. Model. Model
ON-WALL SPEAKERS Model EW25 Model EW30 Model EW35 USER & INSTALLATION MANUAL Introduction Congratulations on your purchase of an EMP Tek EW25, 30 or 35 on-wall Speaker! Your speaker is the result of many
More informationStage 1 Audio Upgrade (BMW Speakers) Installation Instructions for BMW 5 Series, E60 Sedan Logic 7
Stage 1 Audio Upgrade (BMW Speakers) Installation Instructions for 2008-2009 BMW 5 Series, E60 Sedan Logic 7 Tools Required: Metric Socket Set Panel Removal Tool Torx T20 screwdriver Small, Straight Pick
More informationS - SERIES IN-WALL SERIES INSTALLATION MANUAL
S - SERIES IN-WALL SERIES INSTALLATION MANUAL VERSION 2.2 [Skriv tekst] S-15 AND S210... 4 IN-WALL SERIES, S-15IW AND S-16IW... 13 S-15IW AND S-16IW WITH GRILLS... 38 IN-CEILING S-16IW... 64 2 INTRODUCTION
More information2010 Prius Dash Speaker (squawker) Upgrade
2010 Prius Dash Speaker (squawker) Upgrade Author: spiderman Date: Monday, March 21, 2011 Disclaimer Use this document and its contents at your own risk. Forward I want to thank all those members on PriusChat
More informationowner s manual 5.25-inch (130 mm) Convertible 2-Way Component System
owner s manual 5.25-inch (130 mm) Convertible 2-Way Component System Thank you for choosing a JL Audio Evolution C3 Convertible Component System for your automotive sound system. These Evolution Speakers
More informationSpeaker Installation Guide
In This Guide: Installing car speakers often requires removal of door, dash or rear window shelf interior panels to access the speaker mounting points. Component speakers require the additional steps of
More informationHorizontal Blinds Installation Instructions
Horizontal Blinds Installation Instructions Mounting Options Inside mount: Blind is mounted inside the window frame, either to the top of the frame or to the sides. Outside mount: Blind is mounted either
More informationInstallation Instructions Component Systems Professional Line
Installation Instructions Component Systems Professional Line CS - 210 P 3 2-way component system 80 watts art. no. 231495 CS - 230 P 3 2-way component system 100 watts art. no. 231496 CS - 265 P 3 2-way
More informationAMC. Owner s Manual. Sub 12
AMC Owner s Manual Sub 12 SPECIFICATIONS Frequency Range (±2 db): Driver Complement: Dimensions: Installation Environment: Weight: 20 Hz to 80Hz One 12 Cast frame woofer in a front-vented enclosure Enclosure:
More informationMODEL inch, 3-way studio monitor
min max MF min max HF English MODEL 4319 12-inch, 3-way studio monitor quick-start guide Thank You For Choosing This JBL Product Thank you for purchasing the JBL three-way studio monitor 4319. For more
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1964-65 CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE CONTROL
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST PLYMOUTH BELVEDERE
PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1966-67 PLYMOUTH BELVEDERE CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect Fit system. Offers complete comfort capabilities in virtually every
More informationowner s manual ZR525-CSi
ZR525-CSi 5.25-inch (130 mm) 2-Way Component System owner s manual Thank you for choosing a JL Audio Evolution ZR Component System for your automotive sound system. With proper installation, your new speakers
More informationInstallation Instructions
Installation Instructions For Fully Integrated NoFrost Combined Refrigerator-Freezers HC 2062 HCB 2062 HC/HCB 20 7082 373-00 Important PLEASE READ AND FOLLOW THESE INSTRUCTIONS These instructions contain
More informationApplication Guide OE692-FD OE652-FD OE69C-FD OE65C-FD FORD & LINCOLN O.E.M. PLUG & PLAY
OE692-FD OE652-FD OE69C-FD OE65C-FD FORD & LINCOLN O.E.M. PLUG & PLAY Application Guide Please read through this manual to familiarize yourself with your new speakers. Should your PowerBass Autosound speaker
More informationCONGRATULATIONS! TABLE OF CONTENTS. Introduction. Features and Benefits. Parts Guide 4. Installation Considerations 4. Installing the Loudspeakers 6
ceiling mount CM7SD INSTAllation Guide DESIGNER AESTHETICS AUDIOPHILE PERFORMANCE CONGRATULATIONS! Thank you for choosing the Niles CM7SD Loudspeaker. With proper installation, use, and care, your loudspeakers
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST FORD PICKUP
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1960-66 FORD PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationBefore you begin the installation process, gather the following tools and keep them handy:
Vertical Blind Installation Instructions ucontact@udoblinds.com 1-855-205-8442 Congratulations on purchasing vertical blinds from Follow these instructions to properly install your blinds. Tools You Need
More informationPPI PPI PPI SERVICE PPI PPI PPI PPI PPI PPI CAUTION! PPI
Thank you for choosing PPI audio epuipment. Now, HANG ON! PPI products are engineered and manufactured to deliver a wild ride of performance, sound quality, and reliability. This PPI product reflects our
More informationKIT NOTICE. These instructions are for replacing the three existing thermostats with a single new solid-state thermostat.
KIT 06401-004-22-16 5 1 2 NOTICE 3 (3 PLC'S) These instructions are for replacing the three existing thermostats with a single new solid-state thermostat. 4 PREPARATION PARTS INCLUDED 6 1 7 5 8 2 4 (4
More informationF SERIES SPEAKER SYSTEM
INSTRUCTION MANUAL F SERIES SPEAKER SYSTEM F-160G/F-160W (Low impedance) F-160GM/F-160WM (High impedance) F-160WP (High impedance/outdoor use) F-240G/F-240W (Low impedance) F-240GM/F-240WM (High impedance)
More informationInstallation Instructions
Instructions For Fully Integrated NoFrost Combined Refrigerator-Freezers HC 1540/1541 7084 433-00 Important Please read and follow these instructions These instructions contain Danger, Warning and Caution
More informationSERVICE NUMBER: SERV-351
COCA-COLA REFRESHMENTS EQUIPMENT BULLETIN DATE: February 16, 2016 SERVICE NUMBER: SERV-351 REM SUBJECT: True GDM Coolers - Electronic Temperature Control Kit SITUATION / BACKGROUND True has developed a
More informationRetrofit Instructions CLEARVIEW DAY COVER CAUTION: Please read this manual completely before attempting to install, operate or service this equipment
Retrofit Instructions CLEARVIEW DAY COVER CAUTION: Please read this manual completely before attempting to install, operate or service this equipment This manual is Copyright 2019 Duke Manufacturing Co.
More informationProduct Support Bulletin
MODEL: SUBJECT: CONVENTIONAL, W/ C7 CAT ENGINE WEBASTO TSL-17 HEATER Body DATE: APRIL 13, 2004 INDEX: 6 PAGE: 1 OF 16 Before you start this procedure, perform Freightliner Service Bulletin #20-7 first.
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST MUSTANG
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1965-66 MUSTANG CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationEcoBrite Smooth Light LED Light Fixtures
Installation Guide EcoBrite Smooth Light LED Light Fixtures BEFORE YOU BEGIN INSTALLATION Read these instructions carefully. Failure to follow these instructions will invalidate the warranty on this product
More information4545 E Baseline Rd Phoenix AZ Phone: (602) Fax: (602) MODEL MP42B/MODEL MP42W Owners Manual
4545 E Baseline Rd Phoenix AZ 85040 Phone: (602)438-4545 Fax: (602)438-8692 MODEL MP42B/MODEL MP42W Owners Manual CONGRATULATIONS...on your purchase of MTX multi-purpose loudspeakers. Your new loudspeakers
More informationHeater with Air Conditioning. E-Series Ford Aeromaster
Service Guide Heater with Air Conditioning E-Series Ford Aeromaster Contents Blower Motor...2 Plenum Removal...3 Control Module...6 Servo Motors...8 Coolant Valve and Servo Motor...8 Evaporator Recirculation
More informationStep 1: Identify the parts of your shade (parts shown are not to scale)
Motor Operated Solar Shade with Valance Installation and Care Instructions Read carefully and retain for future use. Installation video is available online. Tools required: Philips head screwdriver (not
More informationNS-C8800 Natural Sound Center Speaker System NS-E8800 Natural Sound Effect Speaker System
English NS-C8800 Natural Sound Center Speaker System NS-E8800 Natural Sound Effect Speaker System PRECAUTIONS Read these precautions carefully before using your speakers. Any time you note distortion,
More informationPAL-245 Precision Architectural Loudspeakers
O W N E R ' S M A N U A L PAL-245 Precision Architectural Loudspeakers www.parasound.com 1 Introduction Congratulations on your purchase of your PAL-245 Precision Architectural Loudspeaker system and thank
More informationInstallation Instructions
Installation Instructions For Fully Integrated NoFrost Combined Refrigerator-Freezers HCB 1560/1561 7084 429-00 Important Please read and follow these instructions These instructions contain Danger, Warning
More information2013 PINNACLE LOUDSPEAKERS
Owner s Manual 2013 PINNACLE LOUDSPEAKERS We appreciate your choosing a Pinnacle speaker for use in your Home Theater / Audio system. This unique speaker will provide you with surprisingly powerful and
More informationPAL-265 Precision Architectural Loudspeakers
O W N E R ' S M A N U A L PAL-265 Precision Architectural Loudspeakers www.parasound.com 1 PA L-265 Precision Architectural Loudspeakers Owner s Manual 2 www.parasound.com Owner s Manual PA L-265 Precision
More informationowner s manual XR653-CS 6.50-inch (160 mm) 3-Way Component Speaker System
XR653-CS 6.50-inch (160 mm) 3-Way Component Speaker System owner s manual Thank you for choosing JL Audio Evolution XR Coaxials for your automotive sound system. With proper installation, your new speakers
More informationMopar B-Body Condenser Kit with Drier
an ISO 900:2008 Registered Company 966-70 Mopar B-Body Condenser Kit with 05066 Fits: Plymouth: Belvedere, Satellite, Road Runner (Except 970), GTX Dodge: Charger (Except 966-67), Coronet, Super Bee 8865
More informationKRAMER ELECTRONICS LTD. USER MANUAL MODEL: SPK-W611 Multipurpose Speakers. P/N: Rev 2
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: SPK-W611 Multipurpose Speakers P/N: 2900-300116 Rev 2 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 3 Overview 3 3.1 Defining
More informationINSTALLATION MANUAL FOR MODELS: TERAZZA, TRACCIO, MILANO, CERRATO
INSTALLATION MANUAL FOR MODELS: TERAZZA, TRACCIO, MILANO, CERRATO TABLE OF CONTENTS ROOM SPECIFICATIONS ELECTRICAL SPECIFICATIONS PLUMBING SPECIFICATIONS TECHNICAL SPECIFICATIONS INTRODUCTION ASSEMBLY
More informationInstallation Instructions
Installation Instructions For Fully Integrated NoFrost Combined Refrigerator-Freezers HC 2062 HCB 2062 HC/HCB 2062 7084 445-00 Important Please read and follow these instructions These instructions contain
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1968 CHEVROLET IMPALA
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1968 CHEVROLET IMPALA CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationInstallation Instructions Part No , Part No Part No
Torsion-Flex Motor mount for PSC motors and Rigid-Mount for ECM motors Replacement Kit Cancels: New Installation Instructions Part No. 327752-401, Part No. 327753-401 Part No. 327754-401 IIK-310A-45-11
More informationDRAIN WATER TEMPERING INSTALL
208/230 V DRAIN WATER TEMPERING KIT - 06401-002-59-99 460 V DRAIN WATER TEMPERING KIT - 06401-004-56-12 WARNING WARNING This kit should be installed only by qualified service personnel to reduce the risk
More informationWATTS WALL-MOUNT WIDESPREAD BATHROOM FAUCET INSTALLATION
SKU(s): 940842 WATTS WALL-MOUNT WIDESPREAD BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any
More informationUndercounter Refrigeration
INSTALLATION GUIDE Undercounter Refrigeration Contents Undercounter Refrigeration..................... 3 Undercounter Specifications.................... 4 Site Preparation..............................
More informationINSTALLATION MANUAL SB-AW-SNDBR-X-B
INSTALLATION MANUAL SB-AW-SNDBR-X-B page 2 Support 866.838.5052 INTRODUCTION page 3 We appreciate your purchase and are committed to providing the highest-quality products possible. The SunBrite Outdoor
More informationFOCAL/RENAULT DACIA. INSTALLATION OF LIVE / PREMIUM RENAULT DACIA Lodgy July Version 1.0
FOCAL/RENAULT DACIA INSTALLATION OF LIVE / PREMIUM RENAULT DACIA Lodgy July 2017 Version 1.0 1 RECOMMENDATIONS BEFORE INSTALLATION Reset all car radio audio settings: Ambience = Natural Bass / Midrange
More informationKIT NOTICE. These instructions are for replacing the two existing thermostats with a single new solid-state thermostat.
KIT 06401-004-22-16 5 1 2 NOTICE 3 (3 PLC'S) These instructions are for replacing the two existing thermostats with a single new solid-state thermostat. 4 PREPARATION PARTS INCLUDED 6 1 7 5 8 2 4 (4 PLC'S)
More informationInstallation Instructions
Installation Instructions For Fully Integrated NoFrost Combined Refrigerator-Freezers HC 2060/2061 7082 485-00 Important PLEASE READ AND FOLLOW THESE INSTRUCTIONS These instructions contain Warning and
More informationInstallation Instructions. For the 18 Built-In Dishwasher and Front Color Panels
Installation Instructions For the 18 Built-In Dishwasher and Front Color Panels Printed in USA 154232102 Before You Begin DO NOT INSTALL DISHWASHER UNTIL YOU HAVE READ ALL INSTRUCTIONS. FOR YOUR SAFETY,
More informationInstallation Instructions
Installation Instructions For the 18" Built-In Dishwasher Sears, Roebuck and Co. Sears Canada, Inc. Hoffman Estates, IL 60179 U.S.A. Toronto, Ontario, Canada M5B 2B8 154435201 Before You Begin DO NOT INSTALL
More informationCONGRATULATIONS! TABLE OF CONTENTS. Introduction. Features and Benefits. Parts Guide 4. Installation Considerations 4. Installing the Loudspeaker 6
ceiling mount CM4pr INSTAllation Guide DESIGNER AESTHETICS Audiophile Performance CONGRATULATIONS! Thank you for choosing the Niles CM Series Loudspeakers. With proper installation, use, and care, your
More informationInstallation Manual Mopar Engine Compartment Upgrade Kit
Installation Manual 64-75 Mopar Engine Compartment Upgrade Kit Congratulations... You have just purchased the highest quality, best performing A/C system upgrade ever designed for your Classic Vehicle.
More informationInstallation Instructions
Installation Instructions For Fully Integrated NoFrost Combined Refrigerator-Freezers HCB 1560/1561 HC 1550 7084 327-00 Important Please Read and Follow these Instructions These instructions contain Danger,
More informationMopar B-Body Condenser Kit with Drier
an ISO 900:2008 Registered Company 966-70 Mopar B-Body Condenser Kit with Drier 05066 Fits: Plymouth: Belvedere, Satellite, Road Runner, GTX Dodge: Charger (Except 966-67), Coronet, Super Bee 8865 Goll
More informationUSER MANUAL. Galil 8-C Closed-back Ceiling Speakers MODEL: P/N: Rev 2
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: Galil 8-C Closed-back Ceiling Speakers P/N: 2900-300345 Rev 2 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Recycling
More informationKawasaki Teryx Firestorm Heater Kit Instructions.
Please read all instructions before beginning installation. When working on cooling systems always allow vehicles to cool to avoid being burned or scalded by hot coolant. Always disconnect vehicle s negative
More informationINSTALLATION. Glass Panel Doors (select models) CAUTION
Location Do not install refrigerator near oven, radiator or other heat source. If not possible, shield refrigerator with cabinet material. Do not install where temperature falls below 55 F (13 C) or rises
More informationInstallation Manual PS-200 & PS-201
Installation Manual PS-200 & PS-201 Table of Contents Pre-Uncrating Checklist... 1 Verifying System Requirements... 2 Verifying System Direction... 2 Verifying the Electrical Requirements... 2 Removal
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST CHEVROLET NOVA
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1966-67 CHEVROLET NOVA CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationInstallation Instructions
GE Consumer & Industrial Appliances Installation Instructions Junction Box Cover Within this user bag, you will find a junction box cover and a #10 hex head screw used to attach the junction box cover
More informationInstallation Instructions
Installation Instructions For Fully Integrated NoFrost Combined Refrigerator-Freezers HC 2062 HCB 2062 HC/HCB 2062 7084 341-00 Important Please Read and Follow these Instructions These instructions contain
More informationJOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30)
P. 1 of 12 JOHN DEERE GATOR HPX/XUV 2 PASSENGER HEATER INSTALLATION INSTRUCTIONS (p/n: 9PH20S30) Item: Qty: Description: 1 2 1 x 1 x 5/8 Tee Fitting 2 2 Plastic Snap-in Hose Grommet 3 4 1-1/2" Hose Clamps
More informationInstallation Operation Care
Installation Operation Care Duette and Applause Honeycomb Shades Vertiglide System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Outside
More informationCoaxial speaker. Figure 1 BASIC COAXIAL CONNECTION. Amplifier. Figure 2 BASS BLOCKER db351 WIRING CONNECTION. Amplifier. Bass Blocker.
Figure 1 BASIC COAXIAL CONNECTION Coaxial speaker Amplifier Figure 2 BASS BLOCKER db351 WIRING CONNECTION Amplifier Bass Blocker Figure 3 BASIC COMPONENT CONNECTION INSTALLING db5251& db6501 Crossover
More informationDishwasher. Installation manual DW60M9990AP
Dishwasher manual DW60M9990AP DW9000M_DD68-00197B-00_EN.indd 1 6/1/2017 4:34:14 PM Contents Contents 3 What s included 3 requirements 7 Dimensions and specifications 9 Step-by-step installation 11 2 English
More informationInstallation Manual PS-225 & PS-275
Installation Manual PS-225 & PS-275 Table of Contents Pre-Uncrating Checklist... 1 Verifying System Requirements... 2 Verifying System Direction... 2 Verifying the Electrical Requirements... 2 Removal
More informationIntroduction Page 2. Specifications Page 3. Dimensions Page 4. Included Parts and Accessories Page 6. Tweeter Installation Page 8
Index Introduction Page 2 Specifications Page 3 Dimensions Page 4 Included Parts and Accessories Page 6 Tweeter Installation Page 8 Axis Mount / Phase Plug Installation Page 0 SPZ50 Woofer Installation
More information1SC. Instructions for HORIZONTAL 43 to 54 TV Mounting Bracket
Instructions for HORIZONTAL 43 to 54 TV Mounting Bracket Wall mount your speakers securely enough that they cannot fall and cause personal injury or damage to property. Paradigm DOES NOT supply hardware
More informationCan Am Commander 1000 Radiator Relocation Installation Instructions
Can Am Commander 1000 Radiator Relocation Installation Instructions What comes with the kit 2 CNC Machined Aluminum mounting brackets 2 pcs M6 x 1.0 x 60mm long SHCS 2 pcs M6 x 1.0 x75mm long SHCS 4 pc
More informationWATER DISPENSER INSTALLATION GUIDE
WATER INSTALLATION GUIDE Before you begin: Your dispenser has two lines attached to it. The HOUSE WATER LINE attaches to your house s water supply. The REFRIGERATOR WATER LINE attaches to your refrigerator
More informationMASK4(T) & MASK6(T) Instruction manual
MASK4(T) & MASK6(T) Instruction manual MASK4(T) / 6(T) Instruction manual 1 MASK4(T) & MASK6(T) Manual 2 Cabinet loudspeakers Introduction Please read this manual carefully before using the product. This
More informationPAL-380 Precision Architectural Loudspeakers
O W N E R ' S M A N U A L PAL-380 Precision Architectural Loudspeakers www.parasound.com 1 Introduction Congratulations on your purchase of your PAL-380 Precision Architectural Loudspeaker system and thank
More informationJBL CINEMA SOUND CST56, CSB6, CSC56, CSS11 OWNER S MANUAL
JBL CINEMA SOUND CST56, CSB6, CSC56, CSS11 OWNER S MANUAL Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not
More informationMASK2. Instruction manual
MASK2 Instruction manual MASK2 manual MASK2 Instruction manual 1 2 Cabinet loudspeakers Introduction Please read this manual carefully before using the product. This will give you the necessary product
More informationContents. Instructions for: The Outdoor Speakers by Henry Kloss
Instructions for: The Outdoor Speakers by Henry Kloss Contents Introduction... 1 Unpacking The System... 2 Wiring And Connections... 3 Mounting... 4 Listening Levels And Amplifier Power... 5 7-Year Limited
More informationHEAT/ COOL/ DEFROST FORD THUNDERBIRD
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1964-66 FORD THUNDERBIRD CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationINTRODUCTION. NOTE: Read the entire instruction manual before starting the installation. FIRE, EXPLOSION, ELECTRICAL SHOCK HAZARD
Installation Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY CONSIDERATIONS Improper installation, adjustment, alteration, service, maintenance, or use can
More informationModel 6021 Electrically Heated Rain and Snow Gauge
Model 6021 Electrically Heated Rain and Snow Gauge User s Manual 1165 National Drive Sacramento, California 95834 USA www.allweatherinc.com Table of Contents General Information... 1 Introduction... 1
More informationpg.2 Support:
OWNER S MANUAL ES-500T Series Soundbars ES-500T Series Soundbar Owner's Manual pg.2 www.snapav.com Support: 866.838.5052 ES-500T Series Soundbar Owner's Manual OVERVIEW Welcome to Episode Speakers. We
More informationCEILING FED RISER RAIL KIT. Installation Guide. tritonshowers.co.uk/digital
CEILING FED RISER RAIL KIT Installation Guide tritonshowers.co.uk/digital 2181533B - December 2017 CONTENTS General installation & safety notes (please read)... Installation options... Main components...
More informationS TATEMENT TM M ARTIN L OGAN. the loudspeaker technology company
S TATEMENT TM s e t u p m a n u a l E2 M ARTIN L OGAN the loudspeaker technology company CONTENTS Contents.....................................2 Before You Begin..............................3 Master Packing
More information2010 Sedona Series Components
LIMITED 90-DAY CONSUMER WARRANTY LIMITED TWO-YEAR CONSUMER WARRANTY WITH PURCHASE AND INSTALLATION BY A PRECISION POWER AUTHORIZED DEALER Precision Power promises to the original purchaser, to repair or
More informationKSSS42QDW05, KSSS42QDX05
CABINET PARTS 42" BUILT IN REFRIGERATOR 4 97 Litho In U.S.A. (mek) 1 Part No. CABINET PARTS 1 Cabinet (Not A Serviceable Part) 3 2005004 Grommet, Tube Crossover 4 1112023 Roller, Front & Rear (4) 5 Support,
More informationIWTS Series IWTS-5 LCR & IWTS-10 LCR In-Wall Theater System Speakers. Instruction Manual
IWTS-5 LCR IWTS Series IWTS-5 LCR & IWTS-10 LCR In-Wall Theater System Speakers IWTS-10 LCR Instruction Manual 2 Safety Precautions Table of Contents 2 Model IWTS-5 LCR & IWTS-10 LCR 3 Important Considerations
More informationInstallation Instructions. Instructions de montage. Instrucciones de instalación HC
Installation Instructions For Fully Integrated NoFrost Combined Refrigerator-Freezers Instructions de montage Pour le réfrigérateurs-congélateurs combinés NoFrost encastrés, pour une utilisation intégrée
More information