SOFT-OPEN. B L = Opening width. B = Opening height. * Installation shown with right door opening. For a left opening, make a symetrical drawing.

Transcription

1 SOFT-OPEN INTERIOR DOOR WITH AUTOMATIC OPENER B = Opening height B L = Opening width * Installation shown with right door opening. For a left opening, make a symetrical drawing. L Note: All dimensions in this document are given in mm 1

2 CONDITIONS OF INSTALLATION: - Product intended for indoor use - Installation must be performed by qualified fitters - The editors should be equipped with personal protective equipment Conventional such as gloves, goggles, etc... TOOLS REQUIRED FOR INSTALLATION: - meter - Screwdriver - Drill - Spirit level mm hex wrench provided: for stops rack screw COMPONENTS REQUIRED BUT NOT PROVIDED: - 8 plastic anchors for screws round head Ø4, 5 for rail fixing - 2 countersunk screw Ø4, 5 for setting the ground guide - 2 anchors for screws countersunk head Ø 4.5 for setting the ground guide GENERAL INFORMATION ON SOFT-OPEN INTERIOR DOORS Technical data: Max. weight per panel: 60 kg Operating mode: Automatic door opener. General Data The automatic door opening system is designed to move a sliding door panel with a maximum weight of 60 kg. The panel must be guided at the bottom, in addition to the upper sliding link. This system is intended for indoor use. The automatic opening system you have acquired has been designed and manufactured with great care and must be treated with equal care. In order to benefit fully from the quality and comfort of this product, please follow the installation instructions. The product warranty will only apply if assembly has been performed according to the installation instructions, if good professional practice has been followed, and if the products used (track, pelmet, roller mountings, guides and accessories) are MANTION products. No exceptions shall be made. The product must be stored in a closed, dry location, at a temperature between 0 C and +45 C. MANTION shall not be held liable for any damage to the sliding assembly due to failure to follow good professional practice during installation or use. Check regularly that the damper is working properly and check for signs of wear and damage to the linking cable and its attachment point. Do not dispose of the packaging in the environment. Please recycle according to current local standards (separating cardboard, plastics, and other materials). Prior to installation, ensure that the product is complete and that the structure is capable of bearing the entire 'sliding doors' product. Ensure the pelmets and pelmet ends are properly mounted to prevent the risk of any fingers, hair, or other objects getting caught between the rack and driving pinion. 2

3 Minimum footprint Panel dimensions Lp H B D L 3

4 Composition du kit /Set composition/ Setinhalt/ Composicion del kit Vis / Screw/ Schraube/ Tllo 4,5 x jeu D & G 1 set R&L 1 satz Re&Li 1 juego D&lzq x4 NM SO Mantion S.A.S 7 rue Gay Lussac - F25000 BESANCON Tél Fax

5 Cales de réglages hauteur porte facultative Optional height adjusting plate Einstellkeile für dir Türhöle, nach Bedarf Calces de ajuste, para altura de puerta (facultativa) I II III IV Blue face "L" gear for door opening on the left side Red face "R" gear for door opening on right side Snap retainer 5

6 2-Fitting the track FOR INSTALLATION WITH LEFT DOOR OPENING Track assembly 37 Clearance 12 MAX. 3, Low guide assembly

7 5-Door assembly I II III 6-Installation of door opening machanism for LEFT door opening

8 7-Stopper assembly Open side 11 Close side Position with the door mounting 96 Bay 8-Commisioning SOFT OPEN 8.1 Setting L & R bumpers 8.2 Setting the stop device F+ F- 8

9 8.3 Pelmet support assembly I II III 8.4 Setting the wire I II 9

10 L Bay Bay R Spring is factory load Increase Speed: max. 5 laps / Decrease speed: 3 laps maxi 10

11 9 Trim track 9.1 Pelmet assembly 2 I II III 9.2 endcap pelmet assembly I I 3 3 II II 11