" canopy bracket assembly

Transcription

1 universal suspension key power off power on attention A. suspension system is not recommended for outdoor use. it should not be exposed to water, wind or continuous oscillation. avoid placing luminaires close to hvac vents or in chemical-laden environments such as indoor swimming pools. B. suspension system is suitable for damp locations. C. stop-sleeve on aircraft cable must always be in a free state. locking or clamping of the stop-sleeve will void focal point warranty claims. D. all suspension locations tied off to structure above. E. canopy assembly designed for up to 8/6 cable. cable 8/ tied in knot, where noted in the following instructions, for strain relief. focal point (parts supplied will vary based on suspension kit) " canopy bracket assembly 69 - " canopy bracket assembly suspension kits (xx = suspension length) maximum suspended weight: 5lbs maximum suspended weight: 50lbs junction box assembly 60 - splice box assembly CXX-UNV-8/FD - regular feed 5" canopies CXX-UNV-NOFD - regular non-feed 5.5 canopies CPXX-UNV-8/FD - chicago plenum feed 5 canopies CSXX-UNV-8/FD - feed 5.5 canopies CSXX-UNV-NOFD - non-feed 5.5 canopies JXX-UNV-NOFD - regular non-feed " canopies replacement parts list junction box assembly 69 - canopy bracket assembly canopy bracket assembly 60 - splice box assembly " canopy non-feed " canopy non-feed canopy with feed for use with 5" canopies (709 & 7568) & octagonal junction box maximum suspended weight: 5lbs gasket (chicago plenum only) /8" hex screw /" hex screw 7060-XX - aircraft cable with stop sleeve canopies standard suspension cable coupler cable coupler XX 7650 suspension BY OTHERS OFF TEE INSTALLATIONS - bar hanger SLOPED CEILING NON-FEED - 5.5" non-feed 5.5" feed " non-feed 7060-XX 7750 wood screw JUNCTION BOX ASSEMBLY - octagonal junction box IS066 Rev. M 05 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 5

2 5.5" CANOPY & SPLICE BOX ON TEE (use when suspending from t-bar) non-feed locations follow steps -5 & slide adjuster bracket down until locked on tee all suspension locations must be tied off to structure above / cord inside splice box IS066 Rev. M 05 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 5

3 5.5" CANOPY & SPLICE BOX OFF TEE (use when suspending from bar hanger) non-feed locations follow steps -6 & 8.75 follow manufacturer s instruction for bar hanger 5 slide adjuster bracket down until locked on rail. mounting bracket flush with tile all suspension locations must be tied off to structure above / cord inside splice box IS066 Rev. M 05 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 5

4 5.5" CANOPY & OCTAGONAL JUNCTION BOX (use when suspending directly from junction box) non-feed locations follow steps, &. for s without canopy see bottom of page. off-tee grid installation 8/ cord.75 MAX 80 non-feed without canopy wood screw center cable within slot IS066 Rev. M 05 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 5

5 " CANOPY ON TEE (use when suspending from t-bar) FOLLOW STEPS -5 ON PAGE UTILIZING " CANOPY ASSEMBLY PARTS.75 " CANOPY OFF TEE (use when suspending from bar hanger).75 FOLLOW STEPS -6 ON PAGE follow manufacturer s instruction for bar hanger UTILIZING CANOPY ASSEMBLY PARTS Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC is prohibited. IS066 Rev. M 05 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 5