Technical Reference Manual

Transcription

1 FireShield Technical Reference Manual P/N Rev MAY03

2 DEVELOPED BY Phne:(941) Cpyright IMPORTANT INFORMATION Limitatin f liability This prduct has been designedt meet the requirements f the standards listed in "Cmpliancestatement" belw. Installatin inaccrdancewiththis manual, applicable cdes, and the instructins f the Authrity Having Jurisdictin is mandatry. The manufacturer shall nt under any circumstances be liable fr any incidental r cnsequential damages arisingfrm lss f prperty r ther damages r lsses wing t the failure f prducts beynd the cst f repairr replacement f any defective prducts. The manufacturerreserves the rightt make prduct imprvements and change prductspecificatins at any time. While every precautin has been taken during the preparatin f this manual t ensure the accuracy f its cntents, the manufacturer assumes n respnsibility fr errrs r missins. FCC warning This equipment can generate and radiate radi frequency energy. Ifthis equipment is nt installed in accrdance with this manual, it may cause interference t radi cmmunicatins. This equipment has been tested and fund t cmply within the limits fr Class A digital devices pursuant t Subpart B f Part 15 f the FCC Rules. These rules are designed t prvide reasnable prtectin against such interference when this equipment is perated in a cmmercial envirnment. Operatin f this equipment is likely t cause interference, in which case the user, at his wn expense, will be required t take whatever measures may be required t crrect the interference. Cmpliance statement FireShield, when prperly installed, perates as a Lcal Prtected Premises Fire Alarm System in accrdance with the fllwing standards: NFPA Standard 72,1999 Editin NFPA 70 Natinal Electrical Cde Underwriters Labratries Standard 864,8th Editin Underwriters Labratries f Canada Standard ULC S Canadian Electrical Cde Part I Standard fr Installatin f Fire Alarm Systems ULC S524 Standard fr the Inspectin and Testing f Fire Alarm Systems ULC S536 FireShield als cmplies with Lcal Prtective Signaling (type L) - manual (M), autmatic (A), waterftw (WF), and sprinkler supervisry (SS) fr. Cded (C) and nn-cded signaling (NC) Remte Statin (type RS) - with RPM r FSDACT Auxiliary (type A) - with CTM4.7 (this may include Lcal with Shunt type cnnectin t Master Bx - type LS) Central Statin (Type CS) - with FSDACT Chapter 1 System verview and peratin 1.1 System verview 1.1 Operatins verview 1.1 Cntrls and indicatrs 1.1 Cmpnent descriptins 1.3 Operating the panel 1.4 FSDACT LCD messages 1.7 Chapter 2 Installatin 2.1 Installatin checklist 2.1 Installing the cabinet 2.1 Installing the Remte System Indicatr 2.2 Installing the Remte Zne Indicatr 2.3 Installing the Remte Relay Mdule 2.5 Installing the Pwer ExpanderTransfrmer 2.7 Installing the FSDACT 2.8 Cnnecting an RPM mdule 2.10 Cnnecting a CTM mdule 2.11 Cnnecting an auxiliary pwer supply 2.12 Installing the terminal shield 2.12 Chapter 3 Prgramming 3.1 Overview 3.1 Using the factry default settings 3.2 Using an FSDACT 3.2 Custm prgramming the panel 3.2 FSDACT prgramming 3.8 Chapter 4 Maintenance 4.1 Preventive maintenance 4.1 Appendix A Calculatins A.1 Battery calculatin wrksheet A.1 Ntificatin appliance vltage drp calculatin A.3 Ntificatin appliance circuit maximum wire length calculatin A.4 Appendix B Prgramming templates B.1 Panel prgramming wrksheet B.1 FSDACT prgramming wrksheet B.2 Appendix C Jumper settings and wiring diagrams C.1 Appendix D Panel specificatins D.1 Appendix E Default event cdes E.1 Default Cntact ID event cdes E.1 Default (4/2) event cdes E.2 Z Index -Z.1 FireShield Fire Alarm Cntrl Panel Operating Instructins 1

3 ^ Chapter 1 System verview and peratin System verview FireShield is available in threemdels: three-zne, five-zne, and ten-zne. Eachmdel is similarexceptfr the number f initiating device circuits (IDCs) andntificatin appliance circuits (NACs), as shwn in the fllwing table. Mdel (DCs NACs FS302 (three-zne) 3 2 FS502 (five-zne) 5 2 FS1004 (ten-zne) 10 4 Mdelnumbers may havethe fllwing suffixes: G r R indicates gray r red enclsure, GD r RD indicates panel with FSDACT, GC indicatesulc panel with terminal shield, GF indicates a French ULC panel with terminal shield, and G-2 indicates230 Vac input. Each panelis cnfigured fr ClassB peratin. All mdels except fr the three-zne can be easily cnverted t Class A by using tw Class B circuits t make ne Class A circuit. FireShieldhas the fllwing ptinal cmpnents: Remte System Indicatr (FSRSI) Remte Zne Indicatr (FSRZI-A) Remte Relay Mdule (FSRRM) Pwer Expander Transfrmer (XTR3A120, XTR3A230) (ten-zne nly) DACT (Dialer)/Mdem (FSDACT) City Tie Mdule (CTM4.7) Reverse Plarity Mdule (RPM) Battery Cabinet (BC-2) Refer t Chapter 2 "Installatin*' fr ptinal mdule details. If theptinal FSDACT is installed, the panel: Sends a recrd fthe event t the FSDACT LCD and t the histry lg Usesthe FSDACT t transmit eventmessages t a mnitringstatin as prgrammed Cntrls and indicatrs - REMOTE iscn- HECT ED Frnt panel display (1) Lamp test Buttns REMOTE DISCON NECT WALK TEST minun bait aw TROA TROU&E MU.T «UBM TBOuat CUWMCM NAC1 NAC2 Descriptin O O <D Press the Remte Discnnect and Walk Test buttns simultaneusly t initiate a panel lamp test. This lets yu verify prper peratin f the LEDs n the panel and the remte annunciatrs. Operatins verview The panel perates in nrmalmde in the absence fany alarm, supervisry, truble, r mnitr events. In nrmal mde, the cntrl panel mnitrs the system. The panel perates in ff-nrmal mdeany time an event is intrduced int the system. When this happens, the panel: Changes cntact psitins n apprpriate cmmn relays Activates alarm utputs (fr alarm events nly) Turns n the apprpriate LEDs and the panel buzzer Executes the apprpriate prgrammed utput respnse fr the input that signaled the event Cmmunicates event infrmatin t apprpriate ptinal cmpnents (FSRSI, FSRZI-A, CTM4.7, r RPM) (2) Cntrl buttns Buttn REMOTE DISCON NECT WALK TEST Descriptin Operating mde with FSDACT: Disables r enables FSDACT. Has n effect n alarm relay. Operating mde withut FSDACT: Disables r enables the cmmn alarm relay. Prgramming mde: Selects the next ptin. Operating mde: Places the panel in walk test mde. The Walk Test LED is n when the panel is in walk test mde. Prgramming mde: Selects the previus ptin. 1.1

4 System verview and peratin f^ RESET SIGNAL SILENCE & DRILL PANEL SILENCE Operating mde: Initiatesa panel reset. Prgramming mde: Selects the next setting fr the current ptin. Alarm mde: Silences active ntificatin appliances. Pressing Signal Silence a secnd time turns NACs back n. The Signal Silenced LED indicates when the panel is in alarm and perating with ntificatin appliances turned ff. Visualappliances may r may nt turn ff when Signal Silence is pressed depending n panel prgramming. Nrmal mde: Activates the drill functin. Turns ntificatin appliances n accrding t the panel prgramming but des nt place the panel in alarm r activate the alarm relay. Pressing Drill a secnd time turns ff the drill functin. Prgramming mde: Selects the previus setting f the current prgram ptin. Operating mde: Silences the panel and FSRSI sunders during an active truble, supervisry, r alarm event Prgramming mde: Saves the prgram setting. (3) Indicating Device Circuits (IDCs) LEDs and cntrls LED/buttn Alarm LED Truble LED Supervisry / Mnitr LED (SUP/MON) DISABLE Descriptin On steady when an alarm input device is activated. On steady when there is a wiring fault n the circuit Duble-flashes when the circuit is disabled. Fast-flashes, during walk test, when the IDC is resetting. On steady when a supervisry input device is activated. Stays n until panel is reset. Als flashes when active if prgrammed as a mnitr zne. Mnitr zne prgramming ptin is nt apprved fr use in Canada. Operating mde: Renders an IDC inperative. A disabled circuit can nt initiate a change in panel state. A disabled IDC's Truble LED duble-flashes. Ifpressed when an IDC is active, it has n effect n the panel's current state but n further activityn that IDC willbe reprted. Disabled IDCs remain disabled after a system reset. Walk test mde: Selects an IDCt place it int r remve it frm walk test mde. Prgramming mde: Selects an IDC s that settings can be viewed r changed. (4) Ntificatin Appliance Circuits (NACs) LEDs and cntrls LED/buttn Truble LED DISABLE Descriptin (5) Cmmn system LEDs LED Alarm Truble Supervisry Pwer Disable Annunciatr Truble Battery Truble Grund Fault Walk Test Signal Silenced On steady when there's a wiring fault n circuit. Duble-flashes when circuit is disabled. Operating mde: Used t render an NAC inperative. A disabled NAC truble LED duble-flashes. If pressed when an NAC is active, ntificatin appliances remain active. Once silenced, a disabled NAC des nt resund unless enabled. Disabled NACs remain disabled after a system reset Prgramming mde: Selects an NAC s that settings can be viewed r changed. Descriptin On steady when there is an active alarm event n any IDC. Flashes when there's a fault with a mnitred circuit r system cmpnent, when a circuit is disabled, r when panel is in walk test mde. On steady when there is an active supervisry event n any IDC. On when the panel has AC pwer. Duble-flashes when there is a disabled circuit, FSRRM, alarm relay, r FSDACT. Pressing Disable als places the panel in the truble state. On steady when there is a cmmunicatin failure between the panel and a remte annunciatr. Als places the panel in the truble state. Flashes fr vltage supervisry r charger truble. Steady means placement truble. Als places the panel in the truble state. On steady during an active grund fault Als places the panel in the truble state. Flashes when perfrming an audible walk test. Steady indicates a silent walk test Als places the panel in the truble state. On steady indicates that NAC circuits are turned ff but the panel is still in alarm. (6) LCD display when FSDACT is installed Ntes n LEDs: During an alarm cnditin, allflashing LEDs, regardless ftheir functin, g steady. When NAC r IDC pairs are cnfigured fr Class A peratin, truble cnditins may be indicated by the Truble LED n either NAC r IDC in the pair. 1.2

5 System verviewand peratin Cmpnent descriptins 0 (1) Main AC wiring blck and fuse hlder: Prvides cnnectinsfr 120 r 230 vlt AC (primary pwer) frm dedicatedservice. Includes a primary pwer fuse (5 A). (2) Dual Transfrmer AC wiring blck: Ten-zne panel nly. Prvidescnnectins between primary side f bth main and expandertransfrmerand 120 r 230 vlt AC (fused primary pwer). (3) Transfrmer: Changes 120 r 230 vlt AC supply vltage t 24 vlt AC. (4) Pwer expander transfrmer (XTR3A120, XTR3A230): Optinal. Available fr the ten-zne panel nly. Prvides additinal primary pwer t increase the available NAC current fr the ten-zne panel. (5) Main circuit bard: Prvides cnnectins fr all circuits. Als includes the peratr interface. (6) FSDACT plug: Used t cnnect the FSDACT t the circuit bard. (7) Operatr Interface: Includes peratr cntrls, LED indicatrs, and circuit identificatin labels. (8) Cabinet enclsure: Huses the panel electrnics and standby batteries. In sme cases the batteries may be hused in an external battery cabinet (BC-2). (9) FSDACT: Optinal. Digital alarm cmmunicatr transmitter. Prvides LCD display fr status messages and prgramming menus. Prvides tw telephne line cnnectins fr sending system messages t a cmpatible digital alarm cmmunicatr receiver (DACR). Includes an event histry lg fpanel and FSDACT events. (10) Prgram jumper PRG: Used t place the panel in prgramming mde. (11) Tie wrap munts: Nnpwer-limited. Used t secure wires and t help maintain prper separatinbetweenpwerlimited and nnpwer-limited cnductrs. (12) Tie wrap munts: Pwer-limited. Used t secure wires and t help maintain prper separatinbetween pwer-limited and nnpwer-limited cnductrs. (13) Standby batteries: Prvide secndary/standby pwer t the panel electrnics in the absencefprimary pwer. 1.3

6 System verview and peratin j^\ ^" j^v Operating the panel Resetting the panel Pressing Reset places thepanel inthereset state. Thepanel shuld nt bereset until theapprpriate authrity has determined that the hazard is nlnger present When yu resetthe panel: All LEDsn the panel light fr five secnds The truble and pwerlightsremainn fr an additinal IS secnds Whenreset is cmplete, the buzzersunds (then turns ff) and the truble LED turns ff In this state: All panel indicatrs are temprarily cleared AHntificatin appliances areturned ff All latched IDCs are cleared Alarm, truble, and supervisry relays arereturned t the inactive state Auxiliarypwer(if prgrammed as resettable) mmentarily turns ff At the cnclusin fthe reset, ifan IDC is in an ff-nrmal state, the panel treats the event as a new event and activates the prgrammed respnses. Pressing Disable frthe active IDCwithin 30 secndsafterthe panelhas resetturnsffthe NACs and disables the IDC. If ne r mre IDCs aredisabled prir t initiatin fthe reset, thse IDCs remain disabled. If signal silenceinhibitr resetinhibitis enabled, system reset is inhibited during the silencer resetinhibit perid. T resetthe panel: 1. Press the Reset buttn. Silencing panel and FSRSI buzzers Bth the panel and the ptinal FSRSI mdule have buzzer silence buttns. Pressing the Panel Silence buttn silencesthe buzzer n the panel and n remte FSRSIs. Pressing the FSRSI Silence buttn silences the buzzer n the FSRSI nly. T silence the panel buzzer 1. Pressthe Panel Silence buttn n the panel. 2. Determine the type fcnditin that caused the buzzer t sund: alarm, truble, supervisry, r mnitr. 3. Determine the cause fthe cnditin. T silence an FSRSI buzzer: 1. Press the Silence buttn n the FSRSI. axtiiue&rxtwuxabxxzmtx 2. Determine the type fcnditin that caused the buzzer t sund: alarm, truble, supervisry, r mnitr. 3. Determine the cause fthe cnditin. Silencing ntificatin appliances Pressingthe Signal Silence & Drill buttn turns ffall audible devices. Visual devices rnac circuits mayrmay ntturn ff, depending n panel prgramming. When yu silence thesignals, the Signal Silenced LED lights, indicating that thentificatin appliances are ff. The panel desnt indicate a truble cnditin. If GENESIS, hrn/strbe, r hm-nly devices are used n NACs prgrammed fr GENESIS peratin, Signal Silence& Drill silences nly the hrns. WARNING: The ntificatin appliances shuld nt be silenced until the building is fully evacuated and the cause fthe alarm has been determined. T silence ntificatin appliances: 1. Press the Signal Silence & Drill buttn. When the aut signal silence timer is prgrammed When an event activates the ntificatin appliances, the 20- minute aut signal silence timer is activated. The ntificatin appliances areactivated frthe 20-minute perid. When the timer expires, any NACs that are prgrammed as silenceable aredeactivated, and the Signal Silenced LED is illuminated. Ifanther event takes place that activatesthe previusly silencedntificatin appliances, the Signal Silenced LED turns ff. At any time, yu can deactivate silenceable NACs by pressing Signal Silence & Drill. Nte: NACs activated by IDCs prgrammed as waterflw cannt be silenced until the activated devices are restred t nrmal. Afterthe devices restre,the Signal Silence & Drill buttn r the aut signal silence timer can silence the NACs. Resunding an alarm cnditin Pressingthe Signal Silence & Drill buttn againturns the audible devices back n ifthey were silenced. T resund ntificatin appliances: 1. Press the Signal Silence & Drill buttn. Nte: NACs resund autmatically ifa new alarm (frm anther IDC) is received. 1.4

7 System verview and peratin Disabling an IDC Pressing an IDC Disable buttn prevents thepanel frm respnding tany status change frm that IDC. When yu disable an IDC: The cmmn Disable LED duble-flashes The IDC Truble LED duble-flashes Thecmmn Truble LED lights and thepanel ges int a truble state The cmmn truble relay changes state Resetting the panel hasn effect n a disabled IDC, but remving allpwer frm the panel clears the disable and enables the IDC. Nte: During analarm cnditin, allflashing LEDs g steady. T disable an IDC: GZKsr&xzxzi 1. Press the Disable buttn frthe IDCthatyu wantt disable. Disabling a NAC When yu disable an NAC: The cmmn Disable LED duble-flashes The NAC Truble LED duble-flashes The cmmntruble LED lights andthe panel gesint a truble state The cmmn trublerelay changesstate Resetting the panel has n effect n a disabled NAC, but remving all pwer frm the panel clearsthe disableand enables the NAC. T disable a NAjfr 1. Pressthe Disablebuttn fr the NAC that yu want t disable. Re-enabling an IDC r NAC Yu canre-enable a disabled IDC r NAC. When yu reenable an IDC r NAC: The cmmn Disable LED turns ff The IDC r NAC truble LED turns ff The cmmn Truble LED turns ffand the panel returns t nrmal The IDC r NAC LEDs are updated t shw current status (e.g. ifthe IDC r NAC is in truble, the Truble LED lights). After enabling an IDC, alarms frm that IDC areinhibited fr30 secnds. Duringthis time the IDC can be disabled t avid an unwanted alarm. T re-enable an IDC r NAC: 1. Press the Disable buttn fr the IDC rnac yuwant t re-enable. Using the drill cmmand Yu can use the drill cmmand t activate all fthe ntificatin appliance circuits. Pressing Drill activates all audibles and visuals accrding t the panel prgramming, but des nt activate the Alarmrelay. The FSDACT canbe prgrammedt transmit a drill cnditin, but it will never reprt the drillas an alarm. Drillwill nt perate with an activealarm r supervisry event at the panel. T perfrm a fire drill: 1. Pressand hld the Signal Silence & Drill buttn fr ne secnd. 2. T stp the drill, press and hld the Signal Silence& Drill buttn fr ne secnd. Using the walk test cmmand A walk test lets yu test IDC znes withut having t create an actual alarm cnditin. Yu can cnduct a walk test in silent r audible mde. In silent mde the audible devices (NACs) d nt sund. Walk test will nt peratewith an active alarmr supervisryevent at the panel. Znes shuld be placed in walk test ne at a time. This allws the balance fthe system t remain in service. In a walk test, the panel respnds t the first signalit receives and ignres all thers n that IDC until it clears that signal r the panel is reset The input must be restred t the nrmal state befre the next input is tested. When the input is restred, the panelautmatically resets the circuit being tested. The autmatic reset takes eight secnds. Afterthe circuit is reset the next device can be tested. The panel terminates the walk test ifany fthe fllwing ccur: The panel enters an alarm r supervisry state There are30 minutes finactivity n the zne being tested The panel is reset Walk Test is pressed When yu press Walk Test: The Walk Test LED flashes fr an audible walk test and is steady fr a silent walk test The panel enters a truble state. There is n fire prtectin fr the IDC in walk test. Ifan unselected IDC ges int alarmr truble, all prgrammedutputs perate as prgrammed. 1.5

8 System verview and peratin J^V The IDCyuaretesting behaves as fllws: Fr alarm events, theapprpriate panel, FSRSI, and FSRZI-A LEDs and buzzers are turned n Inthe audible test mde the ntificatin appliances sund fr a number ftimes equal tthe zne number (e.g. three ringsfr znethree) Afteractivatin, the panel resets the IDC. Thiswilltake eight secnds. During the reset perid, theidc truble LED fast-flashes. If thedevice being tested is nt restred, the IDC des nt reset. Ifthe device is restred (n alarm is present) thepanel is ready t testanther device r detectr. If auxiliary pwer is prgrammed as resettable, the auxiliarypwer is deactivated while the zne is reset Input znes prgrammed as waterflw with retard require 10 t 15 secnds factivatin t initiate the test signals Frtruble events, the apprpriate LEDs andthe buzzers are turned n. In the audible (NAC) test mdea nesecnd pulse sunds n the audible devices. After sunding, the zneresets inpreparatin frcntinued testing. Frgrund faultevents, theapprpriate LEDs and the buzzers areturned n. In theaudible (NAC) testmde a ne-secnd pulse sunds n the audible devices. After sunding, the zne resetsin preparatin fr cntinued testing. T cnduct an audible walk test: 1. Press the Walk Test buttn nce. 2. Press thedisable buttn frthe IDCyuwantt test. 3. Cnduct yur walk test fr the IDC. 4. When yuare finished testing an IDC, press the Disable buttn t turn ffthe walk test fr that IDC. 5. Select anther IDC t walk test(steps 2 thrugh 4) rexit frmthe walktest by pressing the WalkTest buttn. Cnducting lamp tests Panel lamp test Apanel lamp test lights all the LEDs n the panel, FSRSIs, and FSRZI-As syu can verify prper peratin. T test panel lamps: cacersasmgsr-e tvsa*smgim^ix3ftftt»«t a3^^ 1. Pressand hld the RemteDiscnnectand Walk Test buttns simultaneusly. 2. Verify prper peratin fallleds n the panel. During lamp tests the LCDdisplays: DB# xx P: x.yy.zz D: x.yy.zz Where: DB# is the database revisin number P: x.yy.zz is the main panel versin D: x.yy.zz is the FSDACT versin FSRSI and FSRZI-A lamp test FSRSI and FSRZI-A mdules canbeinstalled individually r in grups t createa cmplete remte annunciatr. Yucan perfrma lcal lamp test n the FSRSI and FSRZI-A. An FSRSI is required t initiate this functin. T d an FSRSI and FSRZI-Alamp test: 1. Press and hld the FSRSI Silence buttn fr five secnds. 2. Verify prper peratin fall LEDs n the FSRSI and FSRZI-As. T cnduct a silent walk test: 1. Press the Walk Test buttn tw times. 2. Pressthe Disablebuttnfr the IDCyu wantt test. 3. Cnduct yur walk test fr the IDC. 4. When yuare finished testing an IDC, press the Disable buttn t turn ffthe walk test fr that IDC. 5. Selectanther IDCt walktest (steps2 thrugh 4) r exit frm the walk test by pressingthe WalkTest buttn. ^^ 1.6

9 System verview and peratin FSDACT LCD messages Message Peripheral truble Battery Bad Battery Missing AC Failure Charger Truble Grund Fault Transfrmer 2 TR AUX Pwer Trub InternalCmm TR RRM(s) disabled Dialing... DACT Cnfiguratin TRBL DACT Delivery TR DACT Line 1 Trbl DACT Line 2 Trbl Descriptin The panel lst cmmunicatins with the peripherals The battery is bad and needs t be replaced The battery is n lnger cnnected The panel lst AC pwer The panel detected a battery charger truble cnditin. The chargermaynt be ablet chargethe batteries. The panel detected a grund fault The panel detected a truble cnditin in the Pwer Expander Transfrmer The panel detected a truble cnditin in the AUXpwer circuit. Panel-t-FSDACT cmmunicatin fault One r mre FSRRMsare disabled The FSDACTis dialing a DACR FSDACT is nt prgrammed r has unverified changes FSDACT failed tdeliver a message t the receiver r CMS A grund fault r line fault has been detected n Line 1 fthe FSDACT A grund fault r line fault has been detected n Line 2 fthe FSDACT 1.7

10 System verview andperatin ^) 1.8

11 D a Chapter 2 Installatin Installatin checklist D D D Prepare the site:make suretheinstallatin lcatin is free frm cnstructin dust and debris and extreme temperature rangesand humidity. Unpackthe equipment Install the cabinet: See "Installing thecabinet" fr cabinet dimensins. Remvethe clear prtectiveplastic frm the frnt panel display Install ptinal cmpnents (FSRSI, FSDACT, etc.): Seemdule installatin instructins in this chapter. Setthe panel jumpers: SeeAppendix Cr the panel label. Review wire ruting: See Appendix Crthe panel label. Cnnect the field wiring: SeeAppendix Crthe panel label. Meter frpens, grunds, and shrts befre cnnecting. Cnnect AC pwerand grund: See Appendix C rthe panel label. Panel can nt bestarted n batteries nly. WARNING: Make sure that the AC pwer circuit breaker is ffbefrecnnectingwirest the terminal blck. D1 Panel dimensins Mdel D1 [1] D2 D3 D4 D5[1] Three in 3.75 in 9.13 in 10.5 in in and five- (41.9 (9.5 cm) (23.2 (26.67 (36.14 zne cm) cm) cm) cm) Tenzne (60cm) (9.5cm) (19.7 (54.0 ( in 3.75 in 7.75 in in in cm) cm) cm) [1]Add 1-1/2 in (3.81 cm) t D1 and D5 dimensins fr trim kit. -D2- - E 0) O r D3 \ t t -Surface munting hles- D5- -' D4 Cnnect batteries: See Appendix C rthepanel label. Prgram the panel: Refer t Chapter 3. D Test fr prper peratin Installing the cabinet Cabinets canbe surfaced muntedr semi-flushmunted. See the"panel dimensins" figure and table fr framing and munting dimensins. T surface muntthe cabinet 1. Psitin the cabinet n the finished wall surface. 2. Fasten the cabinet t the wall surface where indicated. T semi-flush muntthe cabinet: 1. Frame the interir wall asrequired t supprt the full weight fthe cabinet andstandby batteries. 2. Install (ptinal) semi-flush trim t cabinet 3. Fasten the cabinet t the framing studswhere indicated. 2.1

12 Installatin Installing the Remte System Indicatr The Remte System Indicatr (FSRSI) isa supervised remte annunciatr that prvides remte LED indicatin fpwer, alarm, supervisry, truble, and grund fault cnditins, a' sunder gives audible indicatin during atruble, alarm, r supervisry cnditin. Thesunder can be silenced with the FSRSI Silence switch. Nte: Yu must run the Find Annunciatrs prgram ptin afteradding r remving a remte annunciatr. Theremte annunciatrs will nt perate prperly until the panel detects them. Fr mre infrmatin see Chapter 3"Prgramming." LED State Descriptin Supervisry (yellw) On Truble (yellw) On Grund fault (yellw) Buzzer On On On tempral) On slw pulse) On intermittent) Off Active supervisry device System truble System grund fault System truble Alarm cnditin Supervisry cnditin AC fail Nrmal r silenced Jumper setup Jumper Name Descriptin J2 Grup jumper Allws tw FSRSIs t be cnnected t the same panel. Installthe jumper n nly ne f the tw FSRSIs. Nte: Fr jumper lcatin, refer t the FSRSI wiring diagram. Specificatins Max. per system: 2 Vltage range Minimum: 21 Vdc Maximum: 25 Vdc Current requirements Standby: 12 ma Alarm: 48 ma Max. circuit capacitance: 0.03 uf Max. circuit resistance: 13 hms Wire size Minimum: 18 AWG (0.75 sq mm) Maximum: 12 AWG(2.5 sq mm) Cmpatible electric bx: ANSI/NEMA OSl gang electrical bx Operating envirnment Temperature: 32 t 120 F (0 t 49 C) Humidity: 93% RH, nncndensing LEDs and buzzer LED State Descriptin Pwer (green) On AC pwer present Alarm (red) On Active alarm state Installatin instructins A single FSRSI can bemunted ina standard, single gang electrical bx (ANSI/NEMA OSl-1996) using thesingle gang cverplate that is included. Up t three FSRZI-Aswith r withut anfsrsi can bemunted inanapprved multiple gang electricalbx (ANSI/NEMA OSl-1996) with apprpriate tw, three, r furgang cverplates(mdel numbersfsat-2, FSAT-3,r FSAT-4). Cautin: Makesure all pweris discnnected frm the panel befre installing. Observe static-sensitive handling practices. T install the FSRSI: 1. Verifythat all field wiring is free fpens, shrts, and grund faults. 2. Cnnect wirest the FSRSI as shwn(see wiringdiagram). 3. Usingthe tw plain machinescrews prvided, muntthe mdule t the electrical bx. Nte: Ifyu are using a surface munting bx, yu must install washers (prvided) between the FSRSI and the surface munting bx. 4. Using the white machine screws prvided with the faceplate, munt the faceplate t the mdule. 5. Cnnectthe wirest the terminals in the cntrl panel. 6. Prgramthe FSRSIusing the Find Annunciatrsprgram ptin. Refer t Chapter 3 "Prgramming." 2.2

13 Installatin Installing the RemteZne Indicatr The Remte Zne Indicatr (FSRZI-A) is asupervised remte annunciatr that prvides remte LED indicatin fidcs in alarm state. The FSRZI-A indicates cnditins fr five IDCs. The IDC grups are set by jumpers tindicate znes 1-5r znes Paper inserts are prvided fr labeling the LEDs. Nte: Yu must run the Find Annunciatrs prgram ptin after adding rremving a remte annunciatr. The remte annunciatrs will nt perate prperly until the panel detects them. Fr mre infrmatin see Chapter 3"Prgramming." Installing the FSRSI in an electrical bx Wiring diagram 0^ Frm cntrl panel r previus device Cmmunicatin in - > Ntes Cmmunicatin in + > 24Vin+ > ^1 24V IN + C IN VOUT) C OUT + - <S><S>< ><S> Grup J2 CD - 24Vut + > - 24Vin- 24Vut- 1. All wiringis supervised and pwer limited. Cmmunicatin ut > Cmmunicatin ut + T next device V ut(aux pwer) mustbe prgrammed as nnresettable. Specificatins Max. per system FS302 (three-zne): 2 FS502 (five-zne): 2 FS1004 (ten-zne): 4 Vltage range Minimum: 21 Vdc Maximum: 25 Vdc Current requirements Standby: 8 ma Alarm: 35 ma Max. circuit capacitance: 0.03 uf Max. circuit resistance: 13 hms Wire size Minimum: 18AWG(0.75 sq mm) Maximum: 12 AWG(2.5 sq mm) Cmpatible electric bx: ANSI/NEMA OSl gang electrical bx Operating envirnment Temperature: 32 t 120 F (0 t 49 C) Humidity: 93% RH, nncndensing J^ 2.3

14 Installatin Jumper setup Jumper Name Descriptin J2 J3 J4 J5 Reserved fr future use Zne 6 10 jumper N/A Sets the five LEDs t reprtalarms in znes [1] Zne 1-5 Sets the five LEDs t reprt alarms jumper inznes 1-5. [1] Grup jumper Allws tw FSRZI-As t be cnnected t the same paneland set t the same zne utput ptin. Installthe jumpern FSRZI-As in nly ne fthe tw grups. [1] Install nly ne zne jumpern J3 r J4. Nte: Fr jumper lcatin, refer t the FSRZI-A wiring diagram. Installatin instructins A single FSRZI-A can be munted ina standard, single gang electrical bx (ANSI/NEMA OSl-1996) using the single gang cverplatethat is included. Up t three FSRZI-As with r withut anfsrsi canbe munted inan apprved multiple gang electrical bx (ANSI/NEMA OSl-1996) with apprpriate tw, three, r furgangcverplates (mdel numbersfsat-2,fsat-3, r FSAT-4). Cautin: Makesure all pwer is discnnected frmthe panel befre installing. Observe static-sensitive handling practices. T install the FSRZI-A: 1. Verifymat all field wiring is free f pens,shrts, and grund faults. 2. Cnnectwires t the FSRZI-A as shwn(see wiring diagram). 3. Using the tw plain machine screws prvided, munt the mdule t the electrical bx. Nte: If yu are surface munting the FSRZI-A, yu must install washers (prvided) between the FSRZI-A and the surface munt bx. 4. Usingthe tw white machine screws prvidedwith the faceplate, munt the faceplate t the mdule. 5. Cnnect the wires t the terminals in the cntrl panel. 6. Prgram the FSRZI-A using the Find Annunciatrs prgramptin. Refer t Chapter 3 "Prgramming." Cmpatible electrical bx Installing the FSRZI-A in an electrical bx Wiring diagram Cmmunicatin in - )- Cmmunicatin in + 24Vin + 24 V in - Frm cntrl panel r previus device Ntes ^l J3 E3 rib V Q) <&<2> 24V IN C IN V OUT C OUT < >< >< ) > - 24 V ut + > 24Vut- 1. All wiring is supervised and pwer limited. - - Cmmunicatin ut Cmmunicatin ut V ut (aux pwer) must be prgrammed as nnresettable. T next device 0^ 2.4

15 Installatin JP\ Installing the Remte Relay Mdule The Remte Relay Mdule (FSRRM) prvides five dry cntact relay utputs. The utputs can bewired asbth nrmally pen and nrmally clsed. The utputs can beset t cmmn rzne ntificatins (see the "Cmmand ptins" table belw). Installing the apprpriate jumper (JP3 - JP5) cnfigures the dry cntact relay utput ptins. Five diagnstic LEDs prvide visual indicatin fthestatus f each relay. Ifthe LED is lit, the relay isenergized. Ifthe LED isff, the relay isde-energized. If cnfigured fr cmmn peratin the truble relay and the pwer relay will be energized whenthe system is nrmal. Nte: Yu must run thefind Annunciatrs prgram ptin after adding rremving a remte annunciatr. The remte annunciatrs will ntperate prperly until the panel detects them. Fr mre infrmatin see Chapter 3"Prgramming." Specificatins Max. per system FS302 (three-zne): 4 FS502 (five-zne): 4 FS1004 (ten-zne): 6 Vltage range Minimum: 21 Vdc Maximum: 25 Vdc Zned peratincurrent requirements Standby: 8 ma Alarm: 65 ma Cmmn peratin current requirements Standby:30 ma Alarm: 41 ma Max. circuit capacitance: 0.03 uj Max. circuit resistance: 13 hms Relay ratings: 30Vdc@ 1A (resistive lad) Wire size Minimum: 18 AWG (0.75 sqmm) Maximum: 12AWG (2.5 sq mm) Munting: MFC-A cabinet r listed fire alarm enclsure Operating envirnment Temperature: 32t 120 F (0 t 49 C) Humidity: 93% RH, nncndensing Jumper setup Jumper JP1 JP2 Name Disable jumper JP3 Zne 6-10 jumper JP4 Zne 1-5 jumper JP5 Descriptin Reserved fr future use. Cmmn jumper Disables all utputs. This allws the installert test the system whilethe FSRRM is disabled. Remving the jumper reactivates the FSRRM. The disable jumperis supervised. Withthe disable jumper in place, the panel displays Truble, Annunciatr Truble, Disable, sunds the panel buzzer, and de-energizes any energized relay. Sets the fivedry cntacts t reprt events n znes 6 thrugh 10. See "Cmmand ptins" table. [1] Sets the five dry cntacts t reprt events n znes 1 thrugh 5. See "Cmmand ptins" table. [1] Sets the five dry cntacts t reprt cmmn events. See "Cmmand ptins" table. [1] JP6 Grup The grup jumper (JP6) allws tw jumper FSRRMs t be cnnected t the same panel and set t the same utput ptin. Install the jumper (JP6) t nly ne f the tw gruped FSRRMs. [1] Install nly ne zne jumper n J3 r J4 r J5. Cmmand ptins Mdule type Jumper Output 1 Output 2 Output 3 Output 4 Output 5 Cmmn JP5 Alarm Truble [1] Supervisry Mnitr Pwer [1] Zne 1-5 JP4 Zne 1 Zne 2 Zne 3 Zne 4 Zne 5 JP*s Zne 6-10 JP3 Zne 6 Zne 7 Zne 8 Zne 9 Zne 10 [1jUnder nmrial cnditins the relay is energized(the internal LED is lit). Lssf pwerde-energizes the relay. 2.5

16 Installatin Installatin instructins The FSRRM snaps int asnap track (shipped with the FSRRM), which munts inside a listed fire alarm enclsure. The FSRRM can be psitined in the snap track with the terminal blck facing vertically rhrizntally. Cautin: Make sure all pwer is discnnected frm the panel befre installing. Observe static-sensitive handling practices. T install the FSRRM: 1. Munt themfc-a cabinet using theinstallatin sheet prvided(p/n ). 2. Drill munting hles inthe snap track using the template prvided (P/N ). These hles will align t the munting hles n the MFC-A. An ptinal extended track (P/N FSRRM-S11) is available fr munting tw t fur FSRRM mdules. 3. Munt the snap track t the MFC-A cabinet. 3 T <# Snap track ^ MFC-A Snap track ^ ^ =& 1 0 w z / MFC-A ^, 5. Verify that all wiring is free fpens, shrts, and grund faults. 6. Cnnect the FSRRM t the panel r ther peripheral devices. 7. Pwer up the panel and cnfirm that all relays are in the crrect state befre cnnecting thefield wiring. 8. Cnnect field wires t the FSRRM as shwn in the wiring diagram. Be sure cnnectin will nt adversely affect cntrlled devices (e.g. elevatrs, fans, etc.). 9. Cnnectwiring t the cntrlled devices. 10. Prgram the FSRRM usingthe Find Annunciatrs prgram ptin. Refer t Chapter 3 "Prgramming." Wiring diagram 24 Vin- > 24Vin+ > [1] [2] [2] 24V INC IN C OUT OUT 3 OUT NO C NC NO C NC [2]..[2] I2] HrprF rhr-prf] (Hrpff] OUT 5 NO C NC OUT 4 NO C NC OUT 2 NO C NC Frm cntrl panel r previus device T next device Cmmunicatin in+^- - Cmmunicatin ut- 1 [1] [1] Cmmunicatin in - - Cmmunicatin ut + > 24Vut- [1] V ut + I T next device 4. Insert ne side fthe FSRRM int the./? / snap track slt and snap in the ppsite side. Ntes [1] Supervised and pwer limited. [2] Must be cnnected t a pwer limited surce V ut (aux pwer) must be prgrammed as nnresettable. Service and trubleshting Ifthe Disabled and Annunc Truble LED are lit but n IDC r NAC is disabled then the FSRRM utput is disabled. Snap track 2.6

17 Installatin Installing the Pwer Expander Transfrmer The Pwer Expander Transfrmer (XTR3A120, XTR3A230) prvides additinal primary AC pwer t increase the NAC capacity fr the ten-zne panel. It prvides an additinal 2.5 amps fnac current. The Pwer Expander Transfrmer installs in the cabinet with fur nuts (prvided). The input side f thepwer Expander Transfrmer cnnects t 120 Vacr 230 Vac thrugh the Dual Transfrmer AC Wiring Blck. Its utput cnnects t the circuitbard(j4) withthe attached cable harness. One Pwer Expander Transfrmer canbe installed inthe 10-zne panel. Nte: The Pwer ExpanderTransfrmerdes nt wrkwith thethree-zne r five-zne panels. 3. Cnnect the cable harness tj4nthe circuit bard. Push the cable harness until the cnnectr clicks int place. 4. Cnnect theincming pwer wires t thedual transfrmer AC wiring blck abve theexisting transfrmer. 5. Secure theincming pwer wires t thesidefthecntrl panel with the tie strap prvided. Frm 120 Vac. 15 A, 60 Hz Dedicated branch circuit OR Frm 230 Vac. 15 A. 50/60 Hz Dedicated branch circuit Main AC wiring blck and fuse hlder Dual transfrmer AC wiring blck Specificatins Pwer input Hz (P/N XTR3A120) /60 Hz (P/N XTR3A230) Operating envirnment Temperature: 32 t 120 F (0 t 49 C) Humidity: 93% RH, nncndensing Fuse: Primary winding has thermal current prtectinand is nt field serviceable Tie wrap munts Nte: Input current rating is included with the verall ten-zne ratings. Installatin instructins Cautin: Make sure all pwer is discnnected frm the panel befre installing. Observestatic-sensitive handling practices. T install the Pwer Expander Transfrmer: 1. Psitin the Pwer Expander Transfrmer s that the munting hles align with the fur munting studs n the cntrl panel cabinet. 2. Secure the transfrmer t the panel using the fur nuts prvided. Plug cnnectr Pwer Expander Transfrmer installatin and wiring 2.7

18 Installatin Installing the FSDACT m! ^ IS 3dfgftal alarm cmmunicatr transmitter (DACT) that transmits panel events t acmpatible digital alarm cmmunicatr receiver (DACR). Messages are transmitted ver standard lp-start telephne lines. The dialer is capable fsplit reprting t tw different accunt and telephne numbers. In additin t the DACT functins, this mdule includes: An alphanumeric LCD t display system messages and prgramming prmpts An event histry lg fpanel and DACT events, viewable thrugh cmpatible sftware Amdem fr uplading and dwnlading panel cnfiguratin, histry, and current status t apc running cmpatible sftware Nte: The FSDACT mdem isnly rated fr 2400 baud cmmunicatin. Sme PC mdems may nt be cmpatible with this baud rate. The FSDACT can be prgrammed t perate as asingle r dual line DACT/Mdem/LCD display, a Mdem/LCD display, ran LCD display nly. Fr the FSDACT tbe NFPA 72 CS cmpliant, the fllwing is required: 1. The factry installed warning label must beremved frm thefsdacts line tw phne jack. 2. A secnd phne line, independent fthat used fr line ne must becnnected t phnejack tw. 3. The FSDACT must be prgrammed frdual line peratin. 4. The FSDACT must be prgrammed fr a daily transmissin test frequency. UL 864 cmpliance requires the dual line setting. TheFSDACT can be cnfigured fr attended r unattended dwnlading. JP1 is awire lp (lcated near the tp fthe FSDACT) that cntrlswhich dwnladmethd is used. Leaving the JP1 wire lp intact cnfigures thefsdact fr attended dwnlading. The panel will nt allw changes t the panel rdialer cnfiguratin unless the prgram jumper is inserted. Itwill allw changes t receiver infrmatin (accunt cde, telephne numbers, etc.). UL requires the red wire lp t be intact frall remte statin systems. Cutting thejp1 wire lp cnfigures the FSDACT fr unattended dwnlading. This means that the prgram jumper need ntbe inserted t accept anypanelr dialer cnfiguratin changes. NFPA editin states in that reacceptance testing shall be perfrmed after any change tsite-specific sftware. "All cmpnents, circuits, systems peratins, rsite-specific sftware functins knwn tbe affected by the change r identified by a means that indicates the system peratinal changes shall be 100 percent tested. In additin, 10 percent f initiating devices that are nt directly affected by the change up t amaximum f50 devices, als shall be tested and ' crrect system peratin shall be verified. Arevised recrd f cmpletin in accrdance with shall be prepared t reflect anychanges." Fr additinal dwnlad security, the FSDACT can be prgrammed t perfrm a call back functin. This call back ptin applies whether the FSDACT is cnfigured fr attended runattended dwnlading. Specificatins Current requirements Standby: 40 ma Alarm: 60 ma Operating envirnment Temperature: 32t 120 F(0t 49 C) Humidity: 93%RH,nncndensing Phne line type: ne rtw lp-start lines n a public, switched netwrk Phne line cnnectr: RJ31/38X (C31/38X). Tw 7ft plug crds are shipped with the FSDACT. FCC registratin number: US: EDWAL01BFSDACT Ringer equivalence number: 0.1 Industry Canada Registratin number: IC: 3944-FSDACT Cnnectin between panel and FSDACT: 6-pin cnnectr Cmmunicatin frmats: Cntact ID(SIADC-05) and EST 4/2 (SIA DC-02 P3 with hexadecimal event cdes) Installatin instructins Nte: It is ntnecessary t remve themain panel bard frm the cabinet t install the dialer. Cautin: Make sure all pwer isdiscnnected frm the panel befre remving r installing an FSDACT. Failure t discnnect pwer willdamage the panel andthe FSDACT. Observe static-sensitive handling practices. T install the FSDACT: 1. Remve the blank insert frm the display windw. 2. Remve the clearprtective plastic filmfrmthe FSDACT LCD display. 2.8

19 "tnstallatiarr 3. UseJP1 t cnfigure the FSDACT fr attended r unattended dwnlading: Attended: leave the JP1 wire intact Unattended: cut the JP1 wire 4. Install the dialer t the back fthe circuit bard. Align the LCD display with thepening in the circuit bard. 5. Secure the dialer t the circuit bard with the tw machine screws prvided. 6. Cnnect the pwer cable t J2 n the cntrl panel. 7. Cnnect RJ31X/C3IX jackst thesupplied cables. 8. Cnnect the telephne circuits asrequired. Phne cables (supplied) Line 1 T wall -Ine2 li-c^1] phne jack RJ31jacks FSDACT installatin and telephne circuitcnnectin The FSDACT is listed fr use with the fllwing DACRs Receiver Mdels Frmats Ademc 685 EST 4/2*. Cntact ID FBII CP220 EST 4/2*, Cntact ID Osbme-Hffman OH 2000 EST 4/2*. Cntact ID Radinics D6500 EST 4/2* Silent Knight 9000 EST 4/2* Sur-Gard MLR1.MLR2. MCDI TLR, TLR+ EST 4/2*. Cntact ID * EST 4/2 is SIA DC53-02 P3 with the ability t transmit hexadecimal event cdes. FCC Infrmatin 1. Thedialercmplies with Part68 f the FCCrules. The dialer'sfcc certificatin number and Ringer Equivalence Number (REN) is displayed nthepanel's prgramming label andinthis manual. This infrmatin must be prvided t the telephne cmpany ifrequested. 2. Tw FCC cmpliant telephne crds with 8-pin mdular plugs atbth ends are supplied with the FSDACT. The dialer isdesigned tbe cnnected tthetelephne netwrk using thesupplied crdandan RJ3IX r RJ38X jack,which must als cmply with FCC Part68 rules. 3. The REN is used t determine the maximum number fdevices that may be cnnected tasingle telephne circuit. All telephne devices are assigned a REN. The sum fthe RENs fr all cnnected devices may ntexceed five. Themaximum REN may vary insme areas. Cntact the lcal telephneprviderfr mre infrmatin. 4. Ifthe dialer causes harm t tiie telephne netwrk, the telephne cmpany willntify yuanadvance thattemprary discntinuance f service may be required. Ifadvance ntice is nt practical, the telephne cmpany will ntify yuas snas pssible. Yuwillals be advised f yur right tfilea cmplaint with thefcc, ifyubelieve it is necessary. 5. The telephne cmpany may make changes in its facilities, equipment, peratins, rprcedures that culd affect theperatin fthe dialer. Ifthis happens, thetelephne cmpany will prvide advance ntice inrderfr yu tmake necessary mdificatins tmaintain uninterrupted service. 6. Iftruble isexperienced with the dialer, fr repair rwarranty infrmatin, cntact themanufacturer at: (941) Ifthedialer is causing harm tthe telephne netwrk, the telephne cmpany may request yudiscnnect thedialeruntil the prblem is reslved. 7. Nrepairs maybe perfrmed nthedialer bytheuser. 8. The dialer can nt beused npublic cin phnes rparty line service prvided by the telephne cmpany. Industry Canada Infrmatin NOTICE: This equipment meets theapplicable Industry Canada Terminal Equipment Technical Specificatins. This iscnfirmed by the registratin number. The abbreviatin, IC, befre the registratin number signifies that registratin was perfrmed based na Declaratin fcnfrmity indicating that Industry Canada technical specificatins were met. Itdes nt imply that Industry Canada apprved theequipment. Befre installing this equipment, users shuld ensure that itispermissible t be cnnected tthe facilities fthe lcal telecmmunicatins cmpany. The equipment must alsbe installed using anacceptable methd fcnnectin. The custmer shuld be aware that cmpliance with the abve cnditins may nt prevent degradatin f service in sme situatins. Repairs tcertified equipment shuld becrdinated by a representative designated by the supplier. Any repairs ralteratins made by the user tthis equipment, r equipment malfunctins, may give thetelecmmunicatins cmpanycause t requestthe user t discnnectthe equipment. Users shuld ensure fr their wn prtectin that theelectrical grund cnnectins f the pwerutility, telephne lines, and internal metallic water pipe system, ifpresent, are cnnected tgether. This precautin may be particularly imprtant in rural areas. Cautin: Users shuld nt attempt tmake cnnectins themselves, but shuld cntact the apprpriate electric inspectin authrity, relectrician, as apprpriate. NOTICE: The Ringer Equivalence Number (REN) frthisterminal equipment is 0.1. The REN assigned t each terminal equipment prvides an indicatin f the maximum numberf terminals allwed t be cnnected t a telephne interface. The terminatin naninterface may cnsist fany cmbinatin f devices subjectnly t the requirement thatthesumf the RingerEquivalenceNumbersf all the devicesdes nt exceed five. 2.9

20 Installatin #^ Cnnecting an RPM mdule The Reverse Plarity Mdule (RPM) is an interface between FireShield and a reverse plarity receiver. Itprvides ffpremises signal transmissin fr systems that must cmply with NFPA requirements. When used as a reverse plarity remte statin transmitter, it can be cnnected t either a single circuit (alarm ralarm and truble) rup tthree circuits (alarm, supervisry, and truble). Nte: Frdetailed infrmatin andwiring, referttherpm installatin sheet P/N Belw are applicatin diagrams fr using therpm. Nte: The RPM must be munted in an MFC-A enclsure immediately adjacent t thepanel and incnduit. Alarm transmitted nly NO TRBLC NC NO SUP NO ALM C- _C+ 24VOUT~ FireShield TB3 1ST e e e < Frm ALRM n RPM (brwn wire) Frm COM n RPM < (black wire) < Frm +24 n RPM (red wire) Alarm and truble transmitted n a single circuit Nte: JP1 n the RPM must be OUT. NO TRBLC NC NO SUP NO ALM C- _C+ 24VOUT~ FireShield TB3 m w- < e^ a <FrmTRBLnRPM (yellw wire) < FrmALRM n RPM (brwn wire). Frm COM n RPM "^ (black wire) < Frm +24 n RPM (red wire) Alarm, supervisry, and truble transmitted n separate circuits Nte: JP1 n the RPM must be IN. FireShield TB3 < Frm TRBLn RPM (yellw wire) <FrmSUFVnRPM (range wire) < Frm ALRM n RPM (brwn wire) 24VOUT Frm COM n RPM (black wire) < Frm +24 n RPM (red wire) jpn 2.10

21 tnstaltatiotr j^\ Cnnecting a CTM mdule The CTM4.7 CityTie Mdule is an interface between the cntrl panel ntificatin appliance circuit anda master bx. It prvides ff-premises signal transmissin fr systems that must cmply with NFPA requirements fr Auxiliary Prtective Systems. The CTM4.7 activates a lcal energy fire alarm bx, which prvides a24 Vdc alarm signal (current limited at200 ma). The 4.7 KCl end fline resistr required by the NAC is built in t the CTM4.7. Requirements When cnnecting a CTM tthe panel, the fllwing hardware and prgramming requirements must be met: The NAC used must be dedicated t CTM use nly Allalarm znes must be prgrammed t activate the dedicated NAC The NAC used must nt be prgrammed fr Signal Silence Specificatins Pwer: Nminal 24Vdc@ 200 ma Municipal bx peratin:nminal 24 Vdc Maximum wiringresistance:25 CI Trip current: 200 ma int 14.5 CI cil Maximum current: 300 ma Standby current: 20 ma Munting: Single gang bx Operating envirnment Temperature: 32t 120 F(0 t 49 C) Humidity: 93% RH, nncndensing The fllwing are wiring diagrams shwing hw the plarity switchesduringan alarm cnditin. Panel in nrmal cnditin Panel in alarm cnditin W Ntes Alarm cnditin Ntificatin appliance circuit l=sa Master bx i Municipal circuit [1] 200 ma int a 14.5 CI trip cil max., lp resistance =25 CI [2] This circuit is nnpwer-limited and issupervised fr grunds and pens, but nt shrts [3] Supervised and pwer-limited [4] NAC must be prgrammed fr cntinuus signal [5] CTM4.7 must be munted in the same rm as the panel Nrmal cnditin Master bx [4] [5] Ntificatin appliance circuit Municipal circuit 2.11

22 Installatin Cnnecting an auxiliary pwer supply Aux pwer supplied by the panel cannt exceed 0.5 A. If mre than 0.5 Ais required, yu must use a cmpatible UL/ULC listed fire alarm pwer supply. When using an auxiliary pwer supply, yu must cnnect the -24 Vdc auxiliary terminal at the panel t the -24 Vdc utput terminal fthe listed auxiliary pwer supply used t pwer FireShield devices. Nte: Frdetailed wiring infrmatin, refer t the installatin instructins that came with the auxiliary pwer supply. Aux. Pwer + FireShield FACP T Devices A Max. Installing the terminal shield The terminal shields fr the three, five, and ten zne panels (mdel numbers ending in GC r GF) required fr Canadian installatin, cver and prtect the wirecnnectins at the terminal blcks. T install the terminal shield: 1. Remve the fur crner munting screws frm the circuit bard. Refert the diagram belwfr lcatin. 2. Munt the supplied standffs t the fur crner lcatins where yu remved the screws. 3. Munt the terminal shield t the standffs using the screws yu remved in step 1. Refer t the diagram belw. UL Listed Aux. Pwer Surce T Devices Requiring Additinal Pwer 2.12

23 Chapter 3 Prgramming ANNUN TROUBLE O 16 BATT TROUBLE O 8 GND FAULT 4 Binary numbers WALK TEST O 2 SIGNAL SILENCED O Overview Bttm rw f LEDs Prgram ptins and settings Thefeatures and functins f FireShield can becustmized thrugh prgramming. T custmize the panel, yu chse a prgram ptin, then chse a setting fr that ptin. This chapter shws yu hw tprgram the panel. Prgramming methds FireShield panels can be prgrammed using either ftw methds. First, yu can use the panel's LEDs and switches, with r withut an FSDACT installed. Secnd, yucanuse a PCwithan FSDACT installed. PC prgramming requires anptinal sftware package, the FireShield Cnfiguratin Utility (mdel number FSCU). Refer tthe FSCU nline help system fr cmplete prgramming instructins. Prgramming LEDs Inprgramming mde, the tp rw fpanel LEDs indicates which prgram ptin isselected. Each LED is assigned a binary number, and the ttal value fthe tp rw equals the ptin number. Ifyu are nt familiar with binary numbers, yu cansimplymatch the patternfthe LEDs withthe prgramming instructins. FSDACT display Ifyu are using the ptinal FSDACT t prgram the panel, each ptin and setting is displayed n the LCD display. The tp rw fthe LCD displays the prgram ptin, and the bttm rw displays the setting fr that ptin. Yu can use the prgramming buttns tstep thrugh the ptins and selectthe settings yu want Prgramming buttns The panel buttns take n adifferent functin when the panel isin prgramming mde. The fllwing table shws the buttns and describes what they d in prgramming mde. Buttn REMOTE DISCON NECT WALK TEST RESET Descriptin Selects thenext prgram ptin. The tp rw fleds andthe FSDACT LCD change t shw the ptin selected. Selects the previus prgram ptin. The tp rw f LEDs and the FSDACT LCD change t shw the ptin selected. Selects the next setting fr the current ptin. The bttm rw f LEDs and the FSDACT LCD change t shw thesetting selected. ALARM O 16 Tp rw f LEDs TROUBLE 8 SUP O 4 Binary numbers POWER O 2 DISABLE 1 SIGNAL SILENCE & DRILL PANEL SILENCE Selects the previus setting frthe current ptin. The bttm rw f LEDs and the FSDACT LCD change t shw thesetting selected. Saves the setting yu selected fr the current prgram ptin. Each ptin has a number fpssible settings. The bttm rw f panel LEDs indicates which setting is selected fr the current ptin.the settings are detailed belw in "Custm prgramming thepanel." Again, each LED isassigned a binary number, and the ttal value fthe bttm rw equals the setting number. 0*\ Thevalues f all LEDs litna single rw areadded t determine the ptin rsetting number. Fr example, ifthe Gnd Fault, Walk Test, and Signal Silenced LEDs are lit, the value is7 (4+2+1). This means thatsetting seven fr the current ptin is selected. 3.1