RETROFIT CONTROLLER. Retrofit Energy Controller Any Make PIU/ PMS/ IPMS

Transcription

1 RETROFIT CONTROLLER Retrofit Energy Controller Any Make PIU/ PMS/ IPMS SISPL Retrofit controller is an integrated multifunction high speed micro controller based System. It s having a provision of single phase/three phase mains and DG with Automatic/manual modes of operations. This controller includes protection for mains and DG (as per standards). This controller in having battery and room temperature monitoring facility 1

2 System Retrofit Controller system is designed for telecom sites it is compatible with all PIU/IIMPS/AMF Panel. Where any make of PIU/IPMS /AMF are not working or faulty. System Infra solutions Make Energy Controller is highly reliable & compact in size (Weight=350gm Dimension, Length=366mm. Width=80mm. Height=225mm) The highlighting feature of Retrofit controller is that it reduces the operational costs through a well-researched fuel management system The fault management and functionality units of this system is adaptable for Air-conditioners, Batteries, Fire alarms, Diesel Gen sets, Security, AC Power, DC power, lightening and surge protection, etc. 2

3 FEATURES OF RETROFIT CONTROLLER AC distribution unit. Fire Alarm module. Aviation lamp controller. Auto phase Selector. IPMS logic. SVR controller. Battery Monitoring (Battery Current, SOC, Energy) Real time and events recording. One/Two DG control. Real time restriction for DG running in different time slot. Configuration (almost fifty programmable parameters). This controller follows a rational approach towards power management through a) Integrated AMF Function. b) AC power measurement. c) DG parameter monitoring. d) Alarm Consolidation. e) Remote monitoring facility 3

4 CONTROLLER SPECIFICATION: The Retrofit controller Standard as given below DESCRIPTION Capacity Multi Phase Logic STANDARD SPECIFICATION Range of 5 to 50 KVA Retrofit controller will work on 1Phase, 2phase or 3Phase. Input voltage range on single phase 145V 300V Mechanical CNC Fabricated box, using CRC Sheet duly powder coated, 1.6 mm thick CRC sheet. Split type modular design. Safety MTBF The equipment will ensure IEC safety standards All material & workmanship will be of professional quality to ensure MTBF requirement. The MTBF of the retrofit controller is more than hrs. Compliance Micro Controller CE, Tested for safety, EMI/RFI compliance High-Speed micro controller True RMS for all voltage & current All the inputs to the measurement board will be duly protected against surge as per IEEE The measurement circuit will be rated at least twice of the maximum input range, each independent for AMF & module Time Event Logs RS 232t for SISPL use only Energy Real time & date-programmable Last 1000 events For PC interface to adjust the critical data and unload the alarms, This Port will be used for configuration of PFCs. Will be able to measure the DG energy (Cumulative KWH &Hrs) Will be able to measure the EB energy (Cumulative KWH &Hrs) Will be able to measure the Battery energy (Cumulative KWH & Hrs) Data Transfer Retrofit controller will be equipped with suitable GPRS modem / GPRS DTU and able to process the data. 4

5 DG on load Blackout delay DG cooling time DG start attempts After DG starts and supply is healthy 5 Seconds between mains and DG contactor changeover. 15 minutes Three attempts with delay between attempts ( sec) (settable) DG Lock time After three very short mains restoration minutes, DG will run for 1hrs (settable) continuously. Stop Command Settable from 10 to 50 seconds duration Battery charger & DG controller unit Automatic DG battery, SMPS charger with boost/trickle charging & with constant current charging facility (12V) Provision of Auto manual mode selection Auto Phase The Retrofit Controller will be inbuilt with auto phase selector selector which will select any two phase or single phase out of 3 Phase. There will be a electrical and mechanical interlock between each contactor to avoid short circuit in case of electronic failure Set point-for high Factory set ( ON at 40 C and OFF at ON - 3 C) temperature alarm DG set measurements Mains measurements Battery Mains/DG status, DG accumulated hours, DG voltage, DG Energy Measurement (DG KWH) Input Voltage, Output voltages for line conditioning module, Mains Energy Measurement (EB KWH) Battery running hrs & KWH (Accumulated) measurements LED Indications: Mains ON, DG ON, Smoke/ Fire Alarm, DG Common Fault, Fuel Low, System battery low, High Shelter temperature List of potential Alarms will be extended to NOC / TOC through changeover free dry contacts contact (both NO, NC ). 5

6 Mains fail, Shelter Door open/ Intruder, Low fuel level, Common fault -- LLOP/Alt fault/hct/hwt/v belt/dg fail to start/dg fail to stop, Smoke/Fire, Load on DG, DG Fail to stop, DG Fail to start, DG over load, Shelter high temperature, Site on battery, BTS Battery Low. Standard setting Setting in the Retrofit Controller can change manually & Laptop. Site Calibration All measured parameter can you calibrate through S/W on field Dual DG Logic Will be provided the Dual dg logic on sequential basis. Plot No-382, Third Floor, F.I.E., Patparganj Industrial Area, New Delhi Phone: , Website: 6