BRG-N100 BACnet Objects. BRG-N100 Modbus Register Map

Transcription

1 BRIDGE I-P Units RS-485 Network Bridge with Configurable Display and Alarm Capability 100 SERIES BRG-N100 INSTALL / SETUP DOCUMENT PN: BRG-N100 TYPICAL WIRING DIAGRAM BRG-N100 NETWORK BRIDGE LED PWR LED PWR JUMPER ON JUMPER OFF 1 NET + 1 NET + J2 2 NET J2 2 NET 3 NET COMMON 3 NET COMMON 1 ANALOG INPUT SIG 1 ANALOG INPUT SIG 2 ANALOG GROUND 2 ANALOG GROUND J3 3 NO CONNECTION J3 3 ALARM RELAY COM 4 ALARM LED (+15mA) 4 ALARM RELAY CONTACT 1 24VAC POWER IN J6 1 24VAC POWER IN 2 24V GROUND J6 2 24V GROUND LED PWR JUMPER J3 J6 J2 ANALOG IN/ 24VAC RS-485 ALARM OUT IN GROUND 24VAC ALARM LED GROUND ALARM LED SIGNAL +15 ma ALARM RELAY DRY CONTACT ALARM RELAY COMMON GROUND 24VAC (ONLY WHEN LED PWR JUMPER IS INSTALLED) (ONLY WHEN LED PWR JUMPER IS INSTALLED) (ONLY WHEN LED PWR JUMPER IS REMOVED) (ONLY WHEN LED PWR JUMPER IS REMOVED) TRANSFORMER 24 VAC / HZ (SEE NOTES 2 AND 3) 24 VAC OUT N.O. RELAY DRY CONTACTS 3 AMPS MAX COM LINE IN EXTERNAL LED ALARM INDICATOR EXTERNAL ALARM LED (15 ma) ILLUMINATES ON ALARM (LED PWR JUMPER MUST BE ON ) RELAY ALARM DRY CONTACTS (LED PWR JUMPER MUST BE OFF ) ANALOG DEVICE TO BE MONITORED ANALOG SIGNAL FROM DEVICE TO BE MONITORED + MONITORED ANALOG SIGNAL (TO J3-1) -MONITORED ANALOG SIGNAL COMMON/GROUND (TO J3-2 SEE NOTES 2, 3) SHIELDED TWISTED PAIR (STP) WITH GROUND IS RECOMMENDED (SUPPLIED BY OTHERS) - SEE NOTE 1 RS-485 OUTPUT TO BAS NET COMMON (FROM J2-3) NET (FROM J2-2) NET + (FROM J2-1) BUILDING AUTOMATION SYSTEM NOTES: 1: CONNECT ANALOG SIGNAL AND NETWORK CABLE DRAINS TO EARTH GROUND AT ONE END OF CABLE ONLY. 2. THE BRG-N100 IS A NON-ISOLATED DEVICE USING A HALF-WAVE RECTIFIER ON THE 24VAC POWER INPUT. IF MULTIPLE DEVICES ARE POWERED BY THE SAME TRANSFORMER OUTPUT, ALL GND CONNECTIONS MUST BE COMMON, OR A DEDICATED TRANSFORMER MAY BE USED TO PREVENT EQUIPMENT DAMAGE. 3. ALL DEVICES ON MULTIPLE BRG-N100 INSTALLATIONS WITH A COMMON 24VAC SOURCE MUST BE WIRED IN-PHASE TO THE SAME TERMINALS (e.g.: J6-1 to J6-1, J6-2 to J6-2). 4. SHIELDED TWISTED PAIR (STP) WIRING WITH GROUND IS RECOMMENDED (SUPPLIED BY OTHERS). 5. DRY RELAY CONTACT RATING MAXIMUM 3 AMPS MAXIMUM. EBTRON 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRON ( ) Fax: Internet: EBTRON.com 1

2 BACNET OBJECTS LIST Type, ID Name Default Units Device BRG-N100 BRG-N100 BACnet Objects AI, 1 Analog Input FPM AI, 2 Alarm Status None BO, 1 Relay None BO, 2 LED None Notes: Writable Properties: Present Value, COV, Out of Service, Units, Max Present Value, Min Present Value, Polarity (Relay). Default Baud is 76,800. Internal write is at Priority 16. Priority 1-8 are non-volatile. Notes INACTIVE = Open, ACTIVE = Close; Write at any Priority less than 16 INACTIVE = Off, ACTIVE= On; Write at any Priority less than 16 MODBUS REGISTER MAP Function Address Type Description Range/Value boolean Trouble Status 0:OK, 1:Trbl float AI1 Scaled Value Minscale to Fullscale BRG-N100 Modbus Register Map 16 bit unsigned Alarm Status - Write 0 to clear 0: No alarm 1: High Alarm 2: Low Alarm 3: Both float Analog Input Fullscale 0 to 999, float Analog Input Minscale -999,999 to 999, bit unsigned Relay 0 = Open, 1 = Closed; Any other value clears write bit unsigned LED 0 = Off, 1 = On; Any other value clears write bit unsigned Float word order 0: high word first; 1: low word first Note: Default is 19,200, even parity, 1 stop bit. SYSTEM OF UNITS MENU SYSTEM OF UNITS MENU Simultaneously depress/release ENTER + ESC keys during normal operation to select * Factory Default/Current Setting Enter (move ) Enter (move ) Enter (action, move ) Esc (normal oper.) Esc (move ) Esc (move ) ACTION *IP/SI=IP SYS SET IP/SI? IP/SI=IP SYS IP/SI=SI SYS Set system units to IP (FPM, CFM) Set system units to SI (MPS, LPS) 2 EBTRON 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRON ( ) Fax: Internet: EBTRON.com

3 SETUP MENUS (PART 1 OF 4) SETUP MENU Simultaneously depress/release + keys during normal operation to select * Factory Default/Current Setting Enter (move ) Enter (move ) Enter (move ) Enter (move ) Enter (action, move ) Esc (normal oper.) Esc (move or prev setting) Esc (move or prev setting) Esc (move ) Esc (move ) ACTION SETUP GENERAL *NAME={unit serial#} SET NAME? Instruction text: "USE AND ENT" then: NAME= _ Enter Name for BRG-N100 transmitter (Default = Unit Serial Number) *IN1 TYPE=AIN SET IN1 TYPE? IN1 TYPE=AIN Set input type to Analog Input IN1 TYPE=NET Set input type to Network *IN1 UM=FPM SET IN1 UM? IN1 UM=NONE Set input units of measure. IN1 UM=FPM Note: Changing this value will reset the defaults for fullscale, minscale, and alarm setup. IN1 UM=CFM IN1 UM=% IN1 UM=CUSTOM if IN1 UM=CUSTOM *UNITS=% SET UNITS? USE & ENT Enter custom units. Note: Instructions will be displayed until key is pressed. if IN1 UM=NONE or CUSTOM *PRECIS=1 SET PRECIS? PRECIS=1 Set precision when units of measure is NONE, or CUSTOM. PRECIS=0.1 PRECIS=0.01 PRECIS=0.001 PRECIS= *LLIMIT=0 SET LLIMIT? LLIMIT=0 Set the measurement value below which, readings are ignored by the transmitter. DISPLAY *LCD DSPL=IN1 SET LCD DSPL? LCD TRBL=OFF Set LCD display to OFF or IN1 LCD TRBL=IN1 *LCD TRBL=ON SET LCD TRBL? LCD TRBL=OFF Set LCD to display TROUBLE indication LCD TRBL=ON O 1A O 1B TO PART 4 TO PART 2 EBTRON 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRON ( ) Fax: Internet: EBTRON.com 3

4 SETUP MENUS (PART 2 OF 4) FROM PART 1B O if IN1 TYPE = AIN ANALOG IN *AI1 SGNL=mA SET AI1 SGNL? AI1 SGNL=VDC Set analog input signal type AI1 SGNL=mA if AI1 SGNL=mA *AI1 RNGE=4-20 AI1 RNGE=FIXED if AI1 SGNL=VDC *AI1 RNGE=0-10 SET A1 RNGE? A1 RNGE=0-10 Set analog input signal range A1 RNGE=0-5 A1 RNGE=2-10 A1 RNGE=1-5 *AI1 FS=3000 SET AI1 FS? AI1 FS=3000 Set analog input full scale value *AI1 MS=0 SET AI1 MS? AI1 MS=0 Set analog input minimum scale value *AI1 INTG=3 SET AI1 INTG? AI1 INTG=3 Set analog input integration value (number of readings that are averaged for each input measurement) NETWORK *NETOUT=BACNET SET NETOUT? NETOUT=BACNET Set network output type. Note: If input type is network then BACNET is the only option. NETOUT=MODBUS Modbus is only available if input type is analog. *NETADDR= 2 SET NETADDR? NETADDR=2 Set network address. *NETBAUD=76800 SET NETBAUD? NETBAUD=76800 Set baud rate. NETBAUD=38400 NETBAUD=19200 NETBAUD=9600 if NETOUT = MODBUS *PARITY=EVEN SET PARITY? PARITY=EVEN Set parity. PARITY=ODD PARITY=NONE1 PARITY=NONE2 if NETOUT = BACNET *NETDI=2 SET NETDI? NETDI=2 Set network device instance. if IN1 TYPE = NET *INDI=2 SET INDI? INDI=2 Set input network device instance. *INOBJ=AI SET INOBJ? INOBJ=AI Set input network object type INOBJ=AO INOBJ=AV *OBJID=1 SET OBJID? OBJID=1 Set input network object ID *POLLING=60 SET POLLING? POLLING=60 Set polling time in seconds O 2 TO PART 3 4 EBTRON 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRON ( ) Fax: Internet: EBTRON.com

5 SETUP MENUS (PART 3 OF 4) FROM PART 2 O ALARM *LO ALRM=OFF SET LO ALRM? LO ALRM=OFF Enable LO alarm LO ALRM=ON *HI ALRM=OFF SET HI ALRM? HI ALRM=OFF Enable HI alam HI ALRM=ON *SETPNT=0 SET SETPNT? SETPNT=0 Enter setpoint for alarm *TOLTYPE=% SET TOLTYPE? TOLTYPE=% Set tolerance type, either as a percent of setpoint or as a fixed value above or below setpoint TOLTYPE=VAL *TOL=0 SET TOL? TOL=0 Enter tolerance as fixed value *TOL=10% SET TOL? TOL=10% Enter tolerance as percent of setpoint *DELAY=2 MIN SET DELAY? DELAY=2 MIN Set alarm delay *ZERO OFF=NO SET ZERO OFF? ZERO OFF=NO Enable ZERO OFF. If set to YES, ALARM will be inactive (OFF) when measured input is below LOW LIMIT. ZERO OFF=YES *RESET=AUTO SET RESET? RESET=AUTO RESET=MANUAL Set alarm reset to AUTO or MANUAL. AUTO will clear alarm activation when alarm condition is no longer present. MANUAL requires user to clear alarm activation. RELAY *RLAY ASN=ALRM SET RLAY ASN? RLAY ASN =TRBL Set relay assignment RLAY ASN =ALRM RLAY ASN =BOTH RLAY ASN =NONE *NORMAL=CLOSE SET NORMAL? NORMAL=OPEN Set normal state of relay NORMAL=CLOSE LED *LED ASN=ALRM SET LED ASN? LED ASN =TRBL Set LED assignment LED ASN =ALRM LED ASN =BOTH LED ASN =NONE EBTRON 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRON ( ) Fax: Internet: EBTRON.com 5

6 SETUP MENUS (PART 4 OF 4) FROM PART 1'A' O 4 TOOLS SECURITY *LOCK SEC=LOW SET LOCK SEC? LOCK SEC=LOW Enable LOW setting where code is last four digits of board serial number. LOCK SEC=MED Enable MED setting where code is entered from user. Contact Customer Service to unlock if code is lost. LOCK SET=HIGH Enable HIGH setting where code is entered from user. If code is lost, unit must be returned to factory to unlock. *LOCK=OFF SET LOCK? LOCK=OFF LOCK=ON ENTR CODE:0000 CONF CODE:0000 Enter code and confirm code (NOTE: if LOCK SEC= HIGH, DO NOT lose code!) RESET RESET ALL ARE YOU SURE? RESET ALL=YES Reset transmitter to defaults RESET ALL=NO RESET NET ARE YOU SURE? RESET NET=YES Reset network settings RESET NET=NO RESET TRBL SET ARE YOU SURE? RESET TRBL SET=YES Resets any disabled trouble codes RESET TRBL SET=NO DIAGNOSTICS TRBL CODES 1: (TROUBLE code) DSBL TRBL CODE? DSBL TRBL=NO Do not disable active TROUBLE indication DSBL TRBL=YES Disable active TROUBLE indication TRBL HISTORY 1: (TROUBLE code) View last 5 TROUBLE codes SERIAL NUMBERS UNIT ####### BRD ##### FW REV V1.## INPUT VALUE AIN= ##### Displays input value INPUT VOLTS AI1= ##.### Displays input volts if analog input NET STATUS NO ERRORS Displays network status IG_BRG-N100_R1C 6 EBTRON 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRON ( ) Fax: Internet: EBTRON.com