SETUP MENUS (PART 1 OF 5)

Transcription

1 EF EB-Flow I-P Units Application Specific Airflow Measurement with Temperature & Alarm Capability 2000 SERIES EF-A2000-B INSTALL / SETUP DCUMENT PN: EF-A2000-B TYPICAL WIRING DIAGRAM EF-A2000-B TRANSMITTER LED PWR JUMPER INSTALLED 1: UT 1: FLW R PRESSURE 2: ANALG UT GRUND 3: UT 2: TEMP/ALARM/TRUBLE 4: ALARM LED (+15mA TYP) 5: N CNNECTIN 6: 24V GRUND 7: 24VAC PWER IN LED PWR JUMPER REMVED 1: UT 1:FLW R PRESSURE 2: ANALG UT GRUND 3: UT 2:TEMP/ALARM/TRUBLE 4: ALARM RELAY DRY CNTACT 5: ALARM RELAY CMMN 6: 24V GRUND 7: 24VAC PWER IN LED PWR JUMPER TRANSFRMER 24 VAC / HZ (SEE NTES 2 AND 3) 24 VAC UT LINE IN PRBE 1 PRBE 2 24VAC GRUND EXTERNAL LED ALARM INDICATR (LED PWR JUMPER INSTALLED) ALARM LED GRUND ALARM LED SIGNAL +15 ma (LED PWR JUMPER INSTALLED) (LED PWR JUMPER INSTALLED) EXTERNAL ALARM LED (15 ma) ILLUMINATES N ALARM ALARM RELAY CMMN ALARM RELAY DRY CNTACT (LED PWR JUMPER REMVED) (LED PWR JUMPER REMVED) CM DRY RELAY DRY CNTACTS 3 AMPS MAX) RELAY ALARM (LED PWR JUMPER REMVED) T BLEED SENSR + UT 2 TEMPERATURE/ALARM/TRUBLE (FRM PIN 3) -UT CM GRUND (FRM PIN 2 SEE NTES 2, 3) + UT 1 AIRFLW (FRM PIN 1) -UT CM GRUND (FRM PIN 2 SEE NTES 2, 3) BAS INTERFACE NTES: 1: CNNECT UTPUT SIGNAL CABLE DRAINS T EARTH GRUND AT NE END F CABLE NLY. 2. EF-A2000 IS A NN-ISLATED DEVICE USING A HALF-WAVE RECTIFIER N THE 24VAC PWER INPUT. IF MULTIPLE DEVICES ARE PWERED BY THE SAME TRANSFRMER UTPUT, ALL GND CNNECTINS MUST BE CMMN, R AN ISLATIN TRANSFRMER MAY BE USED T PREVENT EQUIPMENT DAMAGE. 3. ALL DEVICES N MULTIPLE EF-A2000 INSTALLATINS WITH A CMMN PWER 24VAC SURCE MUST BE WIRED IN-PHASE T THE SAME TERMINALS (PIN 6 to PIN 6, PIN 7 to PIN 7). 4. SHIELDED TWISTED PAIR (STP) WIRING (SUPPLIED BY THERS) IS RECMMENDED. EBTRN 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRN ( ) Fax: Internet: EBTRN.com 1

2 SETUP MENUS (PART 1 F 5) SYSTEM F UNITS MENU Simultaneously depress/release ENTER + ESC keys during normal operation to select * Factory Default/Current Setting Enter (move ) Enter (move ) Enter (action, move ) Esc (normal oper.) Esc (move ) Esc (move ) ACTIN *IP/SI=IP SYS SET IP/SI? IP/SI=IP SYS Set system units to Inch-Pound units (FPM, CFM, iwg, sq. ft, F) IP/SI=SI SYS Set system units to International System of Units (MPS, LPS, PA, sq. m, C) SETUP MENU Simultaneously depress/release + keys during normal operation to select * Factory Default/Current Setting Enter (move ) Enter (move ) Enter (move ) Enter (move ) Enter (action, move ) Esc (normal oper.) Esc (move or prev setting) Esc (move or prev setting) Esc (move ) Esc (move ) ACTIN SETUP GENERAL *NAME=EF-A2000 SET NAME? Instruction text: "USE AND ENT" then: NAME= _ Enter Name for transmitter (Default =EF-A2000) *MEAS=AIRFLW SET MEAS? MEAS=AIRFLW Set measurement mode to AIRFLW MEAS=PRESS Set measurement mode to PRESSURE if MEAS=AIRFLW *AIRFLW=ACT SET AIRFLW? AIRFLW=ACT Set the airflow measurement to ACTUAL units (AFPM/ACFM) AIRFLW=STD Set the airflow measurement to Standard units (SFPM/SCFM) *ALT=0 SET ALT? ALT=0 Set the altitude above sea level for flow correction: 0 to 18,000 ft. if MEAS=AIRFLW *AREA=0 SET AREA? AREA=0 Enter area *N FAIL=L SET N FAIL? N FAIL=L Sets transmitter analog output state in the event of a major fault (all sensor failure) expressed as HI for full scale analog output or L as minimum scale analog output. N FAIL=HI *EXT CABLE=0 SET EXT CABLE? EXT CABLE=0 Enter length of extension cable if MEAS=AIRFLW DISPLAY *LCD UM=AFPM SET LCD UM? LCD UM=AFPM LCD UM=ACFM Set LCD units of measure to CFM or FPM. (Note: A if ACT or S if STD measurement prefix set by AIRFLW= setting above) *LCD UM=iWG The text "LCD UM FIXED" flashes to indicate that this setting is fixed and cannot be modified. *LCD DSPL=BTH SET LCD DSPL? LCD DSPL=FF LCD DSPL=TEMP : LCD DSPL=PRESS Set what is displayed on LCD. Note: Will cycle between readings if not able to fit on same screen. Press either ESC or ENTER to stop cycling and press again to continue cycling between readings. if MEAS=AIRFLW: LCD DSPL=FLW LCD DSPL=BTH *LCD INTG=100 SET LCD INTG? LCD INTG=100 Integration samples for LCD *LCD TRBL=N SET LCD TRBL? LCD TRBL=FF Set whether or not TRBLE is displayed on LCD T PART 4 'A' T PART 2 LCD TRBL=N 2 EBTRN 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRN ( ) Fax: Internet: EBTRN.com

3 SETUP MENUS (PART 2 F 5) FRM PART 1 Analog cards only if MEAS=AIRFLW ANALG UT *A1 ASGN=FLW A1 ASGN FIXED The text "A1 ASGN FIXED" flashes to indicate this setting is fixed and cannot be modified. *A1 ASGN=PRESS A1 ASGN FIXED The text "A1 ASGN FIXED" flashes to indicate this setting is fixed and cannot be modified. *A01 SGNL=VDC The text "A1 SGNL FIXED" flashes to indicate this setting is fixed and cannot be modified *A1 RNGE=0-10 SET A1 RNGE? A1 RNGE=0-10 Set range for A1 A1 RNGE=0-5 A1 RNGE=2-10 A1 RNGE=1-5 if MEAS=AIRFLW *A1 UM=AFPM SET A1 UM? A1 UM=AFPM Set A1 units to FPM or CFM (Note: A if ACT or S if STD measurement prefix set by AIRFLW= setting above) A1 UM=ACFM *A1 ASGN=iWG A1 UM FIXED The text "A1 UM FIXED" flashes to indicate that this setting is fixed and cannot be modified. if MEAS=AIRFLW *A1 MS=0 SET A1 MS? A2 MS=0 Set A1 minscale *A1 FS=3000 SET A1 FS? A2 FS=3000 Set A1 fullscale *A1 MS= SET A1 MS? A2 MS= Set A1 minscale *A1 FS=0.25 SET A1 FS? A2 FS=0.25 Set A1 fullscale *A1 INTG=30 SET A1 INTG? A1 INTG=30 Integration samples. Also same as network integration. *A2 ASGN=TEMP SET A2 ASGN? A2 ASGN=TEMP Assign A2 to output temperature, alarm, or trouble A2 ASGN=ALRM A2 ASGN=TRBL *A02 SGNL=VDC The text "A2 SGNL FIXED" flashes to indicate this setting is fixed and cannot be modified *A2 RNGE=0-10 SET A2 RNGE? A2 RNGE=0-10 Set range for A2 A2 RNGE=0-5 A2 RNGE=2-10 A2 RNGE=1-5 if A2 ASGN=TEMP *A2 UM= F A2 UM FIXED The text "A2 UM FIXED" flashes to indicate this setting is fixed and cannot be modified. *A2 MS=-20 SET A2 MS? A2 MS=-20 Set A2 minscale *A2 FS=160 SET A2 FS? A2 FS=160 Set A2 fullscale if A2 ASGN=ALRM or TRBL Set A2 alarm/trouble output state when no alarm/trouble condition is present *N FAULT = HI SET N FAULT? N FAULT = L L = minscale analog output N FAULT = HI HI = fullscale analog output T PART 3 EBTRN 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRN ( ) Fax: Internet: EBTRN.com 3

4 SETUP MENUS (PART 3 F 5) FRM PART 2 ALARM *L ALRM=FF SET L ALRM? L ALRM=FF Enable L alarm L ALRM=N *HI ALRM=FF SET HI ALRM? HI ALRM=FF Enable HI alam HI ALRM=N if MEAS=AIRFLW *ALRM UM=AFPM SET ALRM UM? ALRM UM=AFPM Set alarm units of measure to FPM or CFM (Note: A if ACT or S if STD measurement prefix set by AIRFLW= setting above) ALRM UM=ACFM *ALRM UM=iWG ALRM UM FIXED The text "ALRM UM FIXED" flashes to indicate this setting is fixed and cannot be modified. *SETPNT=0 SET SETPNT? SETPNT=0 Enter setpoint for alarm *TL=0 SET TL? TL=0 Enter tolerance as value above or below setpoint. Units based on ALRM UM= setting. *DELAY=2MIN SET DELAY? DELAY=2 MIN Enter alarm delay *RESET=AUT SET RESET? RESET=AUT Set alarm RESET RESET=MANUAL RELAY *RLAY ASN=TRBL SET RLAY ASN? RLAY ASN=TRBL Assign relay to trouble, alarm, both, or none RLAY ASN=ALRM RLAY ASN=BTH RLAY ASN=NNE *NRMAL=CLSE SET NRMAL? NRMAL=PEN Set NRMAL state of relay NRMAL=CLSE T PART 4 'B' 4 EBTRN 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRN ( ) Fax: Internet: EBTRN.com

5 SETUP MENUS (PART 4 F 5) FRM PART 1 FRM PART 3 4A 4B S if MEAS=AIRFLW *FLW ADJ=FF SET FLW ADJ? FLW ADJ=FF FLW ADJ=N Enable flow adjustments *GAIN=1 SET GAIN? GAIN=1 Enter gain applied to airflow reading *FF=0 SET FF? FF=0 Enter offset applied to airflow reading *PRESS ADJ=FF SET PRESS ADJ? PRESS ADJ=FF PRESS ADJ=N Enable pressure adjustments *GAINP=1 SET GAINP? GAINP=1.000 Enter gain applied to pressure reading *FFP=0 SET FFP? FFP=0 Enter offset applied to pressure reading TLS UTPUT TEST UT1 TEST% SET UT1 TEST%? UT1 TEST%=0 Set UT1 to % of full scale analog output UT2 TEST% SET UT12TEST%? UT2 TEST%=0 Set UT2 to % of full scale analog output if MEAS=AIRFLW FIELD ADJUST RUN FA WIZARD? SET FAW INT FAW INT=300 SET # F FLWS # F FLWS=1 # F FLWS=2 The Field Adjust Wizard will now be engaged as outlined in the following steps. The GAIN and FF values will be updated, and FLW ADJ=N will be set if the wizard is successfully completed. Dashed lines indicate Menus when # F FLWS=2 Set Flow 1 N AND SET T Set Flow 2 N AND SET T FLW1= 0 FLW2= 0 CMPLETE CMPLETE "Wait... %" indicates progress while the Field Adjustment Wizard acquires a large number of samples of airflow rate and averages all of the readings. Display indicates " CMPLETE" when adjustment is complete. If you wish to review the adjustment made, simply navigate back to the SETUP menu and view the S section. RUN FA WIZARD? SET FAW INT FAW INT=300 SET #F PRESS #F PRESS=1 # F PRESS=2 The Field Adjust Wizard will now be engaged as outlined in the following steps. The GAIN and FF values will be updated, and PRESS ADJ=N will be set if the wizard is successfully completed. Dashed lines indicate Menus when # F PRESS=2 SET PRESS 1 N AND SET T Set Flow 2 N AND SET T PRESS1= 0 PRESS2= 0 CMPLETE CMPLETE "Wait... %" indicates progress while the Field Adjustment Wizard acquires a large number of samples of airflow rate and averages all of the readings. Display indicates " CMPLETE" when adjustment is complete. If you wish to review the adjustment made, simply navigate back to the SETUP menu and view the S section. T PART 5 'A' T PART 5 'B' EBTRN 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRN ( ) Fax: Internet: EBTRN.com 5

6 SETUP MENUS (PART 5 F 5) FRM PART 4 'A' FRM PART 4 'B' SECURITY *LCK SEC=LW SET LCK SEC? LCK SEC=LW Enable LW setting where code is last four digits of board serial number LCK SEC=MED Enable MED setting where code is entered from user. EBTRN has ability to unlock if code is lost LCK SET=HIGH Enable HIGH setting where code is entered from user. EBTRN cannot unlock, must return transmitter to EBTRN. *LCK=FF SET LCK? LCK=FF LCK=N ENTR CDE:0000 CNF CDE:0000 Enter code and confirm code (NTE: if LCK SEC= HIGH, D NT lose code!) RESET RESET ALL ARE YU SURE? RESET ALL=YES Reset transmitter to defaults RESET ALL=N RESET SENS ARE YU SURE? RESET SENS=YES Reset sensor data, transmitter resets after completion RESET SENS=N RESET ADJ ARE YU SURE? RESET ADJ=YES Reset Flow/Pressure adjustments to GAIN = 1, FF = 0, FLW/PRESS ADJ = FF RESET ADJ=N RESET TRBL SET ARE YU SURE? YES Resets all disabled trouble codes N DIAGNSTICS TRBL CDES 1: N PRBES (example shown) DSBL TRBL CDE? DSBL TRBL=N Disable active TRUBLE indication DSBL TRBL=YES TRBL HISTRY 1: N PRBES (example shown) View last 5 TRUBLE codes SERIAL NUMBERS BRD ##### C1 ###### Displays probe serial numbers followed by a T if connected and functioning properly and followed by F if not connected or not functioning properly C2 ###### SENS VELCITY 1=#####FPM For sensors =1 to 2 SENS TEMP 1=##.#F For sensors =1 to 2 SENS VLTS 1=H##.## T##.## For sensors =1 to 2 PRBE TYPE TYPE= BLEED IG_EF-A2000-B_R1B 6 EBTRN 1663 Hwy. 701 S., Loris SC Toll Free: 800.2EBTRN ( ) Fax: Internet: EBTRN.com