GLYCOL HEAT EXCHANGE PACKAGE

Transcription

1 Project Item Quantity COOK CHILL SYSTEMS FCSI Section Approval Date HEAT EXCHANGE PACKAGE S: c TJ-100-GHEP c P-TC GHEP Cleveland Standard Features TJ-100 GHEP holds 190 gallons of glycol solution Standard supplied with 5 Hp circulating pump, capacity of 35 GPM at 110 feet of head pressure P-TC GHEP holds 300 gallons of glycol solution Standard supplied with 7.5 Hp circulating pump, capacity of 80 GPM at 120 feet of head pressure Holding Tank: All 304 stainless steel Fully insulated with 3/4 closed-cell, high-density foam insulation Wrapped with stainless steel skin Leak tested to 10 Psi Glycol fill port with built-in overflow 1 NPT manual tank drain Thermowell temperature sensor for maintenance without glycol loss Base Frame All 304 stainless steel Four (4) mounting feet Circulating pump attached Circulating Pump 316 stainless steel pump assembly Stainless steel motor shaft U.L. Rated Nema 4 electrical box, housing the temperature and motor controls Glycol solution (see next page for details) Not supplied by Cleveland Range Options & Accessories 208/3/60; 240/3/60 and 460/3/60 electric voltages 380/3/50 or 575/3/60 -- export voltages Larger pump sizes available based on specific job requirements Unit not supplied with shown disconnect switch Short Form Specifications Shall be CLEVELAND Model: TJ-100-GHEP HEAT-EXCHANGE PACKAGE; 190-gallon tank capacity; fully insulated 304 stainless steel tank and base; fill port with overflow; manual tank drain; 316 stainless steel circulating pump assembly; Thermowell mounted temperature sensor for maintenance without glycol loss; temperature and circulating pump controls; base mounted U.L. rated NEMA 4 electrical box, acceptable for indoor or outdoor installation. Shall be CLEVELAND Model: P-TC GHEP; HEAT-EXCHANGE PACKAGE; 300 gallon tank capacity; fully insulated 304 stainless steel tank and base; fill port with overflow; manual tank drain; 316 stainless steel circulating pump assembly; Thermowell mounted temperature sensor for maintenance without glycol loss; temperature and circulating pump controls; base mounted U.L. rated NEMA 4 electrical box; acceptable for indoor or outdoor installation. SECT. XIV PAGE 47 CLE_6103_ St. Clair Street Cleveland, Ohio, U.S.A Tel: Fax: Web Site:

2 JUNCTION BOX HEAT EXCHANGE PACKAGE 1" NPT TANK DRA Ø3/4" HOLE TYP. MIMUM REAR 6" FRONT 36" RIGHT SIDE 20" LEFT SIDE 6" I 1 2 A H CR3 CR1, CR2 L. 6" M. CIRCULATG PUMP J PLAN VIEW K FRONT 20" M. 6" M PLUMBG LES SHOWN ROTATED FOR CLARITY DIAGRAM C CR3 1 2 CR2 D E CR1 F G PIPE SIZG NOTE: UNIT CONNECTION SIZES ARE NOT TO BE USED AS TERCONNECTG PIPE SIZES. TERCONNECTG PIPE SIZES TO BE DETERMED BY FLOW REQUIREMENTS AND MECHANICAL ENGEER, NOT BY CLEVELAND RANGE. B SIDE VIEW DIMENSIONS A B C D TJ-100-GHEP 41" 57.88" 60" 28" P-TC GHEP 45" 66.75" 76" 30.13" E F G H I J K L 20.5" 18" 2 10" 10.5" 8" 5.63" 4.88" 20.5" 18" " 12.13" 9" 4.88" 4.75" BYPASS RETURN CR1 CR2 CR3 TJ-100-GHEP 1 1/ NPT 1 1/ NPT 1 1/ NPT 5 HP 3 AMP 18 AMP 8 AMP 1,400 lbs 48"W x 63"L x 60"H P-TC GHEP NPT NPT NPT 7 1/2 HP 3 AMP 25 AMP 11 AMP 1,600 lbs W x 73"L x 81"H 120V 1PH-60HZ Shipping NOTE: 1. All designs, specifications and dimensions subject to change without notice. 2. If the reservoir is to be installed outdoors incoming and out going lines need to be insulated against heat and cold. heat tape is required on all lines if the temperatures drop below 10ºf in winter. see note #3. 3. Glycol solution mix ratio: (70/30) 70% water - 30% glycol, (60/40) for outdoor installs with winter temperatures below 0ºF. see note #2. 4. Recommended glycol: dowfrost hd (inhibited propylene glycol) or equal. failure to use the recommended fluid may cause damage to the system. 5. REQUIRED: TJ-100-GHEP: 190 GAL. + line volume (determined by installer). P-TC GHEP: 300 GAL. + line volume (determined by installer). 6. Glycol solution not supplied by cleveland range. STANDARD PUMP SIZE Crate SECT. XIV PAGE 48 CLE_6103_0616

3 PACKAGE CHILLER (air cooled) 48" M WD BAFFLE (18") TYP. BOTH SIDES SEE NOTE / WITH WD BAFFLES WD BAFFLE (18") SEE NOTE 1 4 M AIR FLOW AIR FLOW AIR FLOW 92 1/ 58 7/8" WITH WD BAFFLE 40 7/8" 4 M 48" M 4 M 48" M AC2 78 1/ 66 1/ 31 3/4" AC1 10 1/ 11 1/4" 15 1/4" 44" 88 1/ 21" 88 7/8" 45 TON PACKAGE CHILLER - AIR COOLED CA-45T-ON/AC 30 TON PACKAGE CHILLER - AIR COOLED TJ HP/AC TJ HP/AC CA-45T-ON/AC AC1 AC2 NOMAL COOLG MCA* 67 MCA* 90 MOPD** 1,700 43"W x 96"L x 78"H 2 1/ 2 1/ MCA* 98 MCA* 2,600 9W x 96"L x 88"H 250 MOPD** 110 MOPD** 1. All designs, specifications and dimensions subject to change without notice. 2. All units are shipped with wind baffles in separate crate(s) that must be field installed prior to start-up. 3. Condensing units must not be located in the vicinity of steam, hot air or fume exhaust. 4. Due to the weight of the units, a structural analysis by a qualified engineer is required before mounting on a roof location. 5. All electrical connections should be made in accordance with local, state and federal electrical codes. 6. Incoming and out going lines need to be insulated against heat and cold. 7. Heat tape is required on all lines if the temperatures drop below 10ºf in colder climates. SECT. XIV PAGE 49 CLE_6104_0616

4 PACKAGE CHILLER (water cooled) /8" WC2 23 7/8" 22 3/4" WC1 WC3 30 TON PACKAGE CHILLER - COOLED WC1 WC2 WC3 2 1/ 2 1/ NOMAL COOLG MCA* 61 MCA* 80 MOPD** 1,000 40"W x 61"L x 7H 1. Condensing units must not be located in the vicinity of steam, hot air or fume exhaust. 2. All electrical connections should be made in accordance with local, state and federal electrical codes. 3. For in-side installation and operation only. 4. All plumbing connections should be made in accordance with local, state and federal plumbing codes. SECT. XIV PAGE 50 CLE_6105_0616

5 PACKAGE CHILLER (water cooled) /8" WC2 23 7/8" 22 3/4" WC1 WC3 30 TON PACKAGE CHILLER - COOLED WC1 WC2 WC3 2 1/ 2 1/ NOMAL COOLG MCA* 61 MCA* 80 MOPD** 1,000 40"W x 61"L x 7H 1. Condensing units must not be located in the vicinity of steam, hot air or fume exhaust. 2. All electrical connections should be made in accordance with local, state and federal electrical codes. 3. For in-side installation and operation only. 4. All plumbing connections should be made in accordance with local, state and federal plumbing codes. SECT. XIV PAGE 50 CLE_6105_0616