Fire Alarm System. ServoMaster Installation manual

Transcription

1 Fire larm System ServoMaster Installation manual

2 The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing Consilium S assumes no legal responsibility for any error or damage resulting from the usage of this document Consilium S PO ox 94 NO-04 OSLO NORWY Tel: , Fax: mail@servoteknikkno Internet: wwwconsiliumse Edition E 05 E, Dec 004 Part no: Consilium S

3 Ta ble of Con tents GENERL5 The Pur pose Of This Man ual 5 Def i ni tions 5 3 Rules nd Regulations 5 4 asic Principles For Planning 6 5 ServoMasterConfig, Software Configuration Tool 6 6 The Loop Sys tems 6 6 Col lec tive loops 6 6 d dress able loops 7 63 Shorted and bro ken loop pro tec tion 7 7 Zone Num bers nd Zone d dresses 8 MODULE DESCRIPTION 9 /4/8C, Main Con trol Unit 9 Con nec tors for ex ter nal equip ment 9 OP / OP, Op er a tor Panel 0 3 CLM 00, Col lec tive Loop Mod ule 4 PFR 00, Po ten tial Free Re lay Mod ule 5 MSO 00, Mon i tored Sounder Mod ule 5 MSO power con nec tion 6 CCU 00, Charg ing Con trol Unit 3 7 MPD 00, Mimic Panel Driver Mod ule 3 8 PCU, Protocol Converter Unit 4 3 PNEL CONFIGURTIONS 5 3 ServoMaster a sic 5 3 Ex pan sions Up To d dress able Loops 6 33 Loop Expansion With Collective Loops 7 34 Loop Ex pan sion Up To 3 d dress able Loops 8 35 Dis trib uted Fire larm Sys tems 9 4 DDRESSLE LOOP DETECTORS 0 4 UTD 53, Uni ver sal Tem per a ture De tec tor 0 4 SSD 53, Scat tered Light Smoke De tec tor 0 43 STD 53, Smoke and Heat De tec tor 0 44 MCP 545, Man ual Call Point 45 FDC 00, Fire Door Con trol ler 45 Func tional de scrip tion 46 MU 00, Multi Pur pose d dress Unit 4 5 COLLECTIVE LOOP SENSORS 5 5 SSD 5, Scat tered Light Smoke De tec tor 5 5 UTD 5, Uni ver sal Tem per a ture De tec tor 5 53 MS30Ex, In fra-red Flame De tec tor 6 54 IRM-3/, Ionic Smoke De tec tor 6 55 UFM-80/, Dig i tal UV Flame De tec tor 7 56 STMV, Ther mal De tec tor 7 57 KR, Man ual Call Point 8 58 KSR, Man ual Call Point 8 59 STU-904, Timer Unit 9 59 Dis con nec tion in the end of col lec tive loops 9 59 Dis con nec tion in the mid dle of col lec tive loops Dis con nec tion in ad dress able loops / , Zener ar rier Unit 30 ServoMaster Installation Manual Page

4 6 DETECTOR SES 3 6 US 50 Se ries 3 6 US 50-, uni ver sal base for sur face mount ing 3 6 US 50-, base for hol low ceil ing mount ing 3 63 US 50-3, base for hu mid ar eas 3 64 US 50-4, base for con crete mount ing base se ries for IRM and UFM de tec tors Man ual Call Point Hous ings 34 7 INSTLLTION 35 7 Planning 35 7 Cabling 35 7 d dress able loop 35 7 Col lec tive loop Com mu ni ca tion ca ble Choice Of Ca ble d dress able loop ca bles Col lec tive loop ca bles Com mu ni ca tion ca bles Rec om mended ca ble types Ca ble Ter mi na tion Ground Connections larm pan els Sen sors EX area Sen sor la bel ing 38 8 COM MIS SION ING 39 8 Gen eral 39 8 ServoMasterLink v 39 8 Soft ware down load 39 8 System software 40 8 Check cur rent ver sions 40 8 Up grad ing the sys tem soft ware Power up 4 83 Fault mes sages 4 84 Loop Verification 4 84 Loop ver i fi ca tion from the panel front 4 84 Set ac tive loop 4 84 Loop re set Con fig ure zone ad dresses View miss ing sen sors View unconfigured sen sors View sen sors at wrong po si tion View loop com mis sion ing alarms Loop ver i fi ca tion with ServoMaster Com mis sion ing soft ware tool44 84 Con nec tion and startup Down load via the ServoLink pro gram Commissioning Loops Loop buildup (loop sta tus) Loop ver i fi ca tion (Com mis sion ing) Zone ad dress ver i fi ca tion Cor rect ing the con fig u ra tion pro gram 5 86 De tec tor Test 5 87 Output Test 5 88 Panel Test 5 89 Yearly Test ing nd Ser vic ing ServoMaster Installation Manual Page 3

5 80 Main te nance Panel Sen sors Man ual call points larm units Func tion test 54 9 FULT FIND ING 55 9 Sys tem fault 55 9 Supply fault at tery fault Re plac ing the bat ter ies Sen sor fault Re plac ing sen sors Ground Fault larm ell Out let Fault Fault On Door Hold Out let ddressable Loop Fault Collective Loop Fault larm In put Fault 57 9 Communication Error 58 9 Fault On Re lay Coils Spare Parts 58 0TECHNICL DT TLES 59 0 ServoMaster Mod ules 59 0 Sen sors De vices 60 ServoMaster Installation Manual Page

6 GENERL The Purpose Of This Manual The pur pose of this man ual is to give a guide line how to de sign and plan an in stal la tion of the ServoMaster fire de tec tion sys tem Chap ter and 3 will de scribe the ba sic prin ci ples of the fire alarm panel and how to de sign the fire alarm panel ac cord ing to your needs Chap ter 4 through 7 de scribes how to con fig ure the de tec tion loops and how to plan the in stal la tion of the field equip ment sep a rate sheet is de liv ered with each unit con tain ing mount ing de scrip tion, di men - sions, con nec tions and tech ni cal data Definitions EN 54 Loop Collective loop ddressable loop Sensor ServoLN Local LN ServoMasterConfig European standard defining the function and environmental requirements of fire alarm equipment The wires where all sensors are connected loop system where it is not possible to individually identify each sensor In case of fire alarm it will not be possible to determine which sensor gave the alarm, only which loop loop system where all elements have its own separate address In case of fire alarm it is possible to individually identify each element unit connected to detection loop such as a detector, a call point, a local addressable buzzer, a fire door controller etc The internal RS485 communication bus used to communicate between the different modules in the ServoMaster system The internal communication bus used when output modules are connected directly to a main control unit within the same cabinet software tool for configuration and programming of the ServoMaster fire detection systems 3 Rules nd Regulations The fire alarm panel and all its com po nents have been tested ac cord ing to the EN 54 reg u - lations ny ap pli ca ble na tional reg u la tions have to be re spected ServoMaster Installation Manual Page 5

7 4 asic Principles For Planning The ServoMaster fire de tec tion sys tem is based on mod ules which makes the sys tem ex - tremely flex i ble The fire alarm panel can ei ther be de liv ered as a standalone unit or as a de cen tral ized sys tem where the dif fer ent mod ules are spread out in sev eral cab i nets The fol low ing fac tors de ter mine which sys tem con fig u ra tion is most prac ti cal: Laws, reg u la tions, guide lines Cus tomer re quire ments Size and type of building or ves sel Whether it is a new in stal la tion or a re place ment of an old sys tem Cost / ben e fit ra tio 5 ServoMasterConfig, Software Configuration Tool The ServoMasterConfig soft ware pro gram is a very use ful tool when de sign ing the fire alarm panel y us ing this tool it is pos si ble to con fig ure the whole fire alarm sys tem on a PC The soft - ware tool will cal cu late power con sump tion, bat tery backup re quire ments, etc The con fig u ra tion tool is also used to down load the sys tem con fig u ra tion into the fire alarm panel It is im por tant that the con fig u ra tion of the sys tem al ways is in ac cor dance with the ac tual in stal la tion ny changes in the in stal la tion must be re flected in the con fig u ra tion pro gram and be down loaded to the fire alarm panel The manual for this program can be ordered on CLI 8 Collective Loop Driver 6 The Loop Systems The main con trol units () can be de liv ered with driv ers for col lec tive or ad dress able loops The loop con trol lers are mounted on top of the mod ule There are two types of loop con trol lers: Mod ule CLI Loop con trol mod ule with 8 col lec tive loops Mod ule DLC Loop con trol mod ule with ad dress able loops One mod ule can con tain CLI mod ule (8 col lec tive loops) or DLC mod ules (4 ad dress able loops) It is pos si ble to ex tend the num ber of col lec tive loops by add ing col lec tive loop modules (CLM) on the LocalLan Each CLM mod ule con tains 8 col lec tive loops 3k3 3k3 3k3 3k3 3k3 3k3 3k3 3k3 DLC ddressable Loop Driver DLC ddressable Loop Driver 6 Collective loops The amount of sen sors con nected in a col lec tive loop should not ex ceed 3 Each loop must be ter mi nated with an 5k6 end-of-line re sis tor con nected in the base of the last sen sor in the loop In case of a fire, the fire alarm panel will in di cate in which loop the fire is de tected The fire alarm panel is not be able to de ter mine which sen sor the alarm is com ing from It is pos si ble to have a mix of smoke sen sors, heat sen sors and man ual call points in one loop Collective loop 5k6 ServoMaster Installation Manual Page

8 6 ddressable loops One ad dress able loop can con tain up to 7 sen sors Sen sors can be detectors, manual call points, fire door re lease units, address units, etc The ad dress able loop is formed as a -wire ring loop start ing and end ing in the fire alarm panel This two-wire line sup plies power to all ad dress able de vices, and also pro vides two-way data com mu ni ca tion be tween the panel and the de vices ll sen sors con nected to the ServoMaster ad dress able loops are self ad dress ing Dur ing the ini tial iza tion of the loops, each sen sor will be ad dressed ac cord ing to the place ment in the loop One loop may cover sev eral floors or decks since all con nected sen sors have short cir - cuit protection ddressable loop Shorted and broken loop protection ddressable device ddressable loop ll ad dress able de vices have two con nec tion ter mi nals for the pos i tive loop wires oth ter mi nals can act as both input and out put and thus com mu ni cate in di vid u ally or si mul ta - neously The in- and out go ing neg a tive wires are con nected to one com mon ter mi nal or two in ter con nected ter mi nals There is an elec tronic switch be tween the pos i tive ter mi nals con trolled by the ad dress able de vice The in ter nal switches in the ad dress able devices are ini tially in the open (iso lat ing) state when the fire alarm sys tem is started up The loop con trol ler will au to mat i cally go through a se quence of clos ing the switches one by one, and ver i fy ing the con ti nu ity of the pos i tive loop line af ter clos ing the switch of the last de vice in that loop ro ken loop The elec tri cal con ti nu ity of the ad dress able loop is con tin u ously mon i tored by the panel There will be a fault mes sage on the con trol panel s dis play if there is a break in ei ther wire or in both at the same time ll ad dress able de vices will re main op er a tional with a break in ei ther wire, or even with both wires bro ken at the same time, re gard less of the lo ca tion of the wire break Shorted loop If two loop lines are shorted to gether at any point in the loop, the loop volt age will drop to zero and the cur rent will be lim ited to a safe value The con trol panel will iden tify the short cir cuit con di tion and dis play a fault mes sage ll in ter nal switches will open and the panel will start re build ing the loop by clos ing the switches one by one un til the short cir cuited seg ment is reached short cir cuit con di tion will again be pres ent The panel will mem o rize the lo ca tion of the short and start re build ing the loop a sec ond time It will stop clos ing the iso la tors just be fore the shorted seg ment, and in stead con tinue the re build ing from the other end of the loop gain it will avoid the last and short cir - cuited seg ment ll ad dress able de vices will be re turned to nor mal op er a tion af ter the re build ing se quence is com pleted If there are two short cir cuits on the same loop, all de vices lo cated be tween the two shorts will be left non-op er a tional The panel will iden tify these de vices as faulty ServoMaster Installation Manual Page 7

9 7 Zone Numbers nd Zone ddresses ll sen sors con nected to ad dress able loops will be given an ad dress corresponding to the place ment in the loop The first sen sor (clos est to the / ter mi nals) will get the ad dress, the next ad dress and so on These ad dress num bers are only used dur ing the con fig u ra tion of the sys tem For later iden ti fi ca tion, all sen sors will be re ferred to as a zone num ber and a zone ad dress Dur ing the plan ning of the in stal la tion, the build ing or ves sel should be di vided into log i - cal ar eas or zones There can be up to 99 sen sors within one zone and each zone may con - tain sen sors from sev eral dif fer ent loops Each sen sor within each zone must be given an unique num ber from 0 to 99 The ad dress of the sen sor will be pre sented as a five digit zone ad dress: XXX YY The first three dig its rep re sent the zone num ber be tween 00 and 640 The two last dig its rep re sent the sen sor num ber 0-99 within the zone ZONE 00 ZONE 00 ZONE 003 ddressable loop ddressable loop Dur ing the con fig u ra tion of the sys tem, each zone can be de scribed with a 40 char ac ter text and each sen sor within the zone may also be de scribed with a 40 char ac ter text In the ex am ple below, all the sen sors are in the same zone Dur ing alarm they will all be de - scribed with the same zone text but dif fer ent lo ca tion de tails Zone no Detector no Zone text Zone Deck 3 MVZ Port Side Cabin Detector text 00 0 Deck 3 MVZ Port Side Cabin Deck 3 MVZ Port Side Corridor The zone iden ti fi ca tion is to tally in de pend ent from the ad dress num ber that rep re sent in which or der the sen sors are con nected on the loop One zone may only in clude sen sors from the same sub sys tem ServoMaster Installation Manual Page

10 4 4 C C MODULE DESCRIPTION The ServoMaster con cept in cludes a range of dif fer ent mod ules which are used to build up the sys tem ac cord ing to the cus tom ers needs E /4/8C, Main Control Unit The main con trol unit is a fire alarm controller without power sup ply, dis play or key - board ll ServoMaster fire alarm pan els must con tain at least one mod ule The mod ule can be de liv ered in three dif fer ent ver sions: for addressable loops (not available as expansion module) 4 for 4 addressable loops 8C for 8 collective loops Ex pan sion mod ules are de liv ered for TS35-rail mount ing The mod ules must be pow ered from a 8 VDC power sup ply and a 4 V backup battery The mod ule must be mounted in side a metal box to gether with power sup ply and bat tery Other mod ules may also be mounted in side the same box The op er at ing panel can be mounted on the box (com pact ver sion) or de liv ered separately (dis trib uted ver - sion) The mod ule has con nec tors for power, loops and alarms as shown in the ta ble be low Connectors for external equipment FUSES PS 50T TT 50T DH 0T 0T 0T CH 0T CH 0T Local LN / RSQ interface 6 CO TT PS DH 8 0 E NO C NC T RTN CHG NO FULT C NC NO FIRE C NC L L Charger voltage Do not readjust! PC INTERFCE Module address selection CO NC NO C NC TSNS GND L L V CH D V CH D IP IP IP IP L4 L3 NOTE: CODE CON NECT FUNC TION Max RTING FUSE CO- Con trol Out lets Relay contacts for external functions Ini ti ated by fire alarms 3 VC/DC - 3 TT attery input ackup battery connection 4 V - h 5 T PS Power Sup ply Internal power 8 VDC T DH Door hold magnets Power for fire door mag nets Re leased by fire alarms 4 VDC - 08 T - larm ells Power for alarm bells and sound ers Ini ti ated by fire alarms 4 VDC - 08 T FULT Warn ing light, etc Relay output for indication of HW and SW faults in the sys tem 3 VC/DC - FIRE Warn ing light, etc Relay output for indication of fire alarms 3 VC/DC - L-4 ddressable Loop -wire ring bus for ad dress able sensor connection 50 m out CH- ServoLN x 4-wire bus for in ter con nec tion 4 VDC - 08 T be tween con trol mod ules and op er - ating panels L ackup Line -wire bus for backup of data on CH and CH IP General alarm in put External general alarm button with one con tact clo sure 00 m out End of line = 0K IP Reserved input Customer specified contact closure 00 m out End of line = 0K LN Lo cal LN bus 0-wire for mod ule con nec tion PC Configuration PC ServoConfig system configuration The con fig u ra tion tool ServoConfig will cal cu late the cor rect ad dress se lec tor switch set - tings for each mod ule Re place fuses with same type and rat ing! e sure not to in ter change fuse val ues! In case of short cir cuits, se ri ous dam age on wir ing and electronic circuits may re sult if rated cur rent is ex ceeded! ServoMaster Installation Manual Page 9

11 MENU LRMS MENU LRMS POWER POWER FULT SYSTEM FULT TEST DISLEMENTS 4 LRM SOUNDERS DELYED OPERTOR CCESS C DEF GHI JKL MNO PQR STU VW XYZ FULT SYSTEM FULT TEST DISLEMENTS C DEF GHI JKL MNO PQR STU VW XYZ LRM TRNSMISSION DELYED LRM TRNSMISSION CTIVE LRM SOUNDERS DELYED OPERTOR CCESS C Charger voltage adjustment Do not readjust! FUSES PS 50T TT 50T DH 0T 0T 0T CH 0T CH 0T Local LN E PC interface For maintenance use only! Module address selection UPPER ROW CO Control Outlet TT attery PS Pow Supply DH Door Hold larm ells larm ells FULT FIRE L ddressable loop L ddressable loop NO C NC T RTN CHG NO C NC NO C NC 4 V - 8 VDC Power Power GPT-G MF/MS lack Red - SEC Mains 0K LOWER ROW CO Control Outlet Do not connect L ackupline CH ServoLan CH ServoLan IP Input IP Input L4 ddressable loop L3 ddressable loop NO C NC TSNS GND L V D V D IP IP Power OP L L L V D V D OPERTOR PNEL 8k 0k STD / SSD / UTD SW SW OP V D V D OPERTOR PNEL STD / SSD / UTD 3 MCP OP V D V D OPERTOR PNEL 0 wire 0 wire 0 wire PFR / MPD / CLM / MSO PFR / MPD / CLM / MSO PFR / MPD / CLM / MSO FIRE Normal operation FIRE NEXT LRM Normal operation NEXT LRM :47 LRM SILENCE :47 LRM SILENCE SERVOTEKNIKK OP / OP, Operator Panel The pri mary func tion of the op er a tor panel is to pro vide both vi sual and au di ble in for - ma tion about the sta tus of the fire alarm sys tem The op er a tor panel is equipped with a 6 lines graph i cal dis play with ad just able back-light, seven LEDs for sta tus in for ma tion and a key board with all nec es sary keys for op er at ing the fire alarm sys tem The op er a tor panel is is de liv ered in two flush-mount ver sions: OP Single height operator panel frame OP Dual height frame with one operator panel The op er a tor panel can be mounted on a con trol unit box (com pact ver sion) for sur face mount ing, or for separate flush mount ing (dis trib uted ver sion) Sin gle op er a tor pan els are de liv ered with out back boxes ack boxes are de liv ered sep a rately if re quired Three dif fer ent op er at ing lev els can be set dur ing the con fig u ra tion se quence: Operating level 0 allows silence of the internal buzzer Operating level allows silence of all acoustic alarms in the system Operating level all operations possible ll operating levels can display sensor status, list disabled sensors, perform lamp test of the unit and display event log and display setup The op er at ing panel is con nected to the main con trol unit via two shielded four-wire ca bles with ServoLan bus and power ServoMaster ServoMaster OP shown in marine version OP shown in land version with two additional indicator lights for alarm transmission There can be up to 6 op er a tor pan els con nected to one mas ter con trol unit See the User Manual for further description on ServoMaster operation, alarm messages and menu functions RIDGE Main control Console mounted distributed version ulkhead mounted compact version ServoMaster Installation Manual Page

12 Ser voteknikk GND D V L RS-85/4VDC/L L L L3 L4 L5 L6 L7 L8 COMM 3 CLM 00, Collective Loop Module The Col lec tive Loop Mod ule CLM 00 is used to add 8 two-wire col lec tive loops (L)to the ServoMaster The sen sors on the de tec tion loops are not ad dress able The end-of-line re sis tance is 5k6 GND CLM 00 must be con nected to a mod ule through a lo cal LN flat ca ble The mod ule ad dress is cal cu lated by the con fig u ra tion tool and set by a DIP switch on the board Data com mu ni ca tion is in di cated by a LED The unit is pre pared for TS35-rail mount ing in side the ServoMaster cab i net Local LN EMC gnd ddress select 0 CLM Node Switch No No = = = = = = = Used for test only Local LN COMM GND D V L RS-85/4VDC/L L L L3 L4 L5 L6 L7 L CLM 8 x Collective loops 5k PFR Node Switch No No = = = = = = = 4 PFR 00, Potential Free Relay Module The Po ten tial Free Re lay Mod ule PFR 00 is used to add four re lay change over con trol out lets (CO) to the ServoMaster Each re lay has NC/NO con tacts for max 50 VC/DC - Each re lay has a sta tus in di ca tion light ll re lays can be ac ti vated by an op tional by pass ON switch or de ac ti vated by an op - tional by pass OFF switch PFR 00 must be con nected to a mod ule through a lo cal LN flat ca ble The unit ad dress is cal cu lated by the con fig u ra tion tool and set by a DIP switch Data com mu ni ca tion is in di cated by a LED The unit is pre pared for TS35-rail mount ing in the ServoMaster cab i net or in a sep a rate cab i net pre pared for 8 mod ules ypass ON Local LN ypass OFF PFR COMM Re4 Re3 Re Re ddress select Outlet 4 Outlet 3 Outlet Outlet NO C NC NO C NC NO C NC NO C NC POWER POWER Local LN Used for test only ServoMaster Installation Manual Page

13 4 C MSO 00, Monitored Sounder Module The Mon i tored Sounder Mod ule MSO 00 is used to add four alarm bell () out lets D /OFF /ON CHG T PW MSO Node Switch No No = = = = = = = to the ServoMaster MSO 00 can also be used to con trol fire door mag nets MSO 00 has 4 x 4 VDC out lets for max 08 load ll out lets are in di vid u ally fused by Each out let has a sta tus in di ca tion light ll re lays can be ac ti vated by an op tional by pass ON switch or de ac ti vated by an op - tional by pass OFF switch Power for the sound ers or fire door mag nets is de liv ered from the fire alarm panel MSO 00 must be con nected to a mod ule through a lo cal LN flat ca ble and the power is sup plied from the charger and bat tery The unit ad dress is cal cu lated by the con fig u ra tion tool and set by a DIP switch Data com mu ni ca tion is in di cated by a LED The unit is pre pared for TS35-rail mount ing in the ServoMaster cab i net or in a sep a rate cab i net pre pared for 8 mod ules TTERY CHG T ypass ON ypass OFF Local LN Local LN D /OFF /ON CHG T PW COMM /OFF /ON CHG T ddress select OUTLET4 OUTLET3 OUTLET OUTLET 0k 0k 0k 0k 5 MSO power connection 4 3 MSO attery/power The TT and PS screw ter mi nals on the is not dimensioned to re ceive more than one 5 mm ca ble each The con nec tion of a unit re quire a power tap con nec tor on these ca bles Use the en closed SCOTCHLOK 560 IDC elec tri cal tap con nec tors to con nect the MSO to the power run ca bles as shown be low MSO must be con nected to bat tery Place unstripped run wire in side run chan nel In sert un stripped 5 mm tap wire com pletely 3 Use a pair of pliers to crimp the u-contact down flush with the plas tic hous ing 4 Close hinged top cover un til latched E To attery To Power D /OFF /ON CHG T PW T RTN CHG CHG T MSO ServoMaster Installation Manual Page

14 CCU Node Switch No No 3 90 = = = = = = = = 6 CCU 00, Charging Control Unit The Charging Con trol Unit CCU 00 is used to sup ply sys tems with 4-8 main con trol mod ules () and to charge ex ter nal bat ter ies The 8 VDC power sup ply can be rated up to 0 out put at tery size de pends on ex pected backup time Stan dards are 4 V - 4, 36 and 65 h In puts are fused by 5 and out puts are fused by 0 The power and bat tery out puts are con nected to the mas ter The CCU is con nected to the mas ter mod ule via ServoLN CH The mod ule ad dress must be set to The last digit (0-7) is set by a DIP switch The unit is pre pared for TS35 rail mount ing in an external cabinet CCU ddress select TEMP SENS CH D- D T OUT TTERY DC OUT POWER 8 VDC 4 V 4-6 h 30 VC MINS MSTER D- D T RTN CH ServoLN CHG TTERY POWER SUPPLY MPD 00, Mimic Panel Driver Module The Mimic Panel Driver MPD 00 is used to con trol LEDs on cus tom made mimic pan els The panel shows a con tour of the build ing or ship where LEDs in di cate fire alarms, fire door po si tions, fire damp ers, etc D V -V V LT RS-485/4VDC LMP T One mod ule can han dle up to 64 sin gle color LEDs or 3 dual color LEDs Up to 8 MPD mod ules can be con nected to one (max 5 LEDs) NOTE: e aware that the max num ber of outputs from one mod ule is 5 This in - cludes all out puts con nected to the loop, such as ad dress able loop buzz ers, fire door controllers etc ll LEDs can be tested by push ing an op tional lamp test but ton The LEDs are con nected to the MPD mod ule via four 34 pin flat ca ble con nec tors MPD 00 must be con nected to the mod ule through a lo cal LN flat ca ble The unit ad dress is cal cu lated by the con fig u ra tion tool and set by a DIP switch Data com mu ni ca tion is in di cated by a LED The unit is pre pared for TS35 rail mount ing in an ex ter nal cab i net MIMIC PNEL Local LN LMP T ddress select V LT MPD Only for test Local LN LMP TEST ServoMaster Installation Manual Page 3

15 MENU LRMS MENU LRMS NEXT LRM NEXT LRM LRM SILENCE LRM SILENCE POWER POWER FULT SYSTEM FULT TEST DISCONNECTION C DEF GHI JKL MNO PQR STU VW XYZ FULT SYSTEM FULT TEST DISCONNECTION C DEF GHI JKL MNO PQR STU VW XYZ ServoMaster ServoMaster 3 4 V D V D D TXD RXD PCU, Protocol Converter Unit The PCU is used to com mu ni cate be tween the ServoMaster and 3 rd party equip ment Typ i cal ap pli ca tions are re port ing to a "Voy age Re corder", pocket pag ing system or in - ter face to the ServoView PC ap pli ca tion The PCU is a node on the ServoLan bus where both chan nels are used Communication with 3 rd party equip ment is via a 9-pin D-SU or screw ter mi nal RS-3 (0 V, RXD, TXD) or RS-485 (, D / ) Stan dard sup ported pro to cols and sys tems are: ESP 444 Nov 984 Pag ing, PC pre sen ta tion sys tems, etc (Some sys tems may need spe cial ad ap ta tion) NME 083 Voy age data re corder ServoView Only one 3 rd party unit can be served from one PCU Up to 8 PCUs can be con nected to the ServoLan Each PCU is given a unique ad dress (30-37) cal cu lated by the con fig u ra tion tool The cor re spond ing last digit (0-7) is set by a DIP switch on the PCU Data com mu ni ca tion is in di cated by a LED The unit is pre pared for TS35 rail mount ing in an ex ter nal cab i net Ch Ch ServoMaster Config PCU Node Switch No No 3 30 = = = = = = = = FIRE ServoMaster member # ServoMaster member #n FIRE ServoLan master PCU 3 4 D - D V D - D V RXD TXD - D D RS-3 or RS-3 or RS-485 3rd party system 0 The PCU con fig u ra tion data is pre pared using the ServoMaster PC con fig u ra tion pro - gram The pro to col and com mu ni ca tion pa ram e ters are set and the gen eral text string for - mat to be trans mit ted is cho sen The con fig u ra tion data generated by ServoMaster Config will be stored in ServoMaster Sys tem con - fig u ra tion file and down - loaded by the ServoMasterLink applica - tion dis trib uted through the master PCU Configuration Protocol and communcation Protocol type ESP 444 PC Communcation port RS3 aud rate Databit Parity Stopbit bit None bit General text string format Fields in plain text Message type State Sorce type Zone address Date Time Zone text Field separator Detector text <VT> ServoMaster Installation Manual Page

16 3 PNEL CONFIGURTIONS 3 ServoMaster asic 3 C 8V DC ServoLan Ch ServoLan Ch ackup Line OP FIRE POWER FULT SYSTEM FULT SERVOTEKNIKK :47 TEST LRM SOUNDERS DELYED DISLEMENTS OPERTOR CCESS 4V Detection Loop Driver Detection Loop Driver Normal operation C DEF GHI JKL MNO PQR 3 STU VW XYZ 0 MENU LRMS NEXT LRM LRM SILENCE ServoMaster DDRESS UNIT MU-5 DDRESSLE FIRE LRM SYSTEM Fire alarm panel ServoMaster 4 with four addressable loops 3 C 8V DC ServoLan Ch ServoLan Ch ackup Line OP FIRE POWER FULT SYSTEM FULT SERVOTEKNIKK :47 TEST LRM SOUNDERS DELYED DISLEMENTS OPERTOR CCESS 4V 8 Collective Loop Driver Normal operation C DEF GHI JKL MNO PQR 3 STU VW XYZ 0 MENU LRMS NEXT LRM LRM SILENCE ServoMaster 3k3 3k3 3k3 3k3 3k3 3k3 3k3 3k3 Central unit ServoMaster 8C with eight collective loops and separate operator panel Min i mum con fig u ra tion of a fire alarm panel is one (main con trol unit), one power sup ply, one set of bat ter ies and one op er a tor panel ServoMaster Installation Manual Page 5

17 MENU LRMS NEXT LRM LRM SILENCE POWER :47 FULT SYSTEM FULT TEST DISLEMENTS LRM SOUNDERS DELYED OPERTOR CCESS C DEF GHI JKL MNO PQR STU VW XYZ SERVOTEKNIKK Console FIRE Normal operation See sec tion for more information on ServoMaster cabinets 0 Wall mount ServoMaster NOTE: The fire alarm panel is de liv ered in two ver sions: Wall mount: The operator panel is built in to the cabinet front Console: The alarm panel is delivered without operator panel The operator panel must be ordered separately The ba sic ServoMaster may have one or two ad dress able ring loop driv ers, each serv - ing two ad dress able loops, or one col lec tive loop driver board serv ing up to 8 col lec - tive loops with end-of-line re sis tors ServoMaster fire alarm pan els are there fore de liv ered in 6 dif fer ent ba sic ver sions The max i mum amount of sen sors is 7in an ad dress able loop and 3 in a col lec tive loop Up to 6 op er a tor pan els can be con nected to one ServoLN bus sys tem For se cu rity rea sons, the op er a tor pan els must be con nected via two in de pend ent buses, ServoLN CH and ServoLN CH backup line is used to trans mit a com mon fire alarm if the CPU in the main con trol unit is out of func tion The amount of op er a tor pan els must be cal cu lated in ac cor dance with the to tal power con sump tion us ing the ServoMasterConfig soft ware tool The unit is pow ered by a 30 VC / 8 VDC-3 power sup ply and a 4 V backup bat tery The units are housed in a dark blue steel cab i net in tended for use in dry in door en vi ron - ments 3 Expansions Up To ddressable Loops 4V 3 C 8V DC Operator panel OP CH CH V D V D Slave FIRE POWER :47 Normal operation MENU NEXT LRM LRMS LRM SILENCE SERVOTEKNIKK FULT SYSTEM FULT TEST LRM SOUNDERS DELYED DISLEMENTS OPERTOR CCESS C DEF GHI OP 3 C 8V DC ServoLan Ch ServoLan Ch ackup Line attery Master 8 VDC power Slave Slave 4V JKL MNO PQR 3 STU VW XYZ 0 ServoMaster T TT RTN CHG PS V D V D CH Master CH T TT RTN CHG PS V D V D CH Slave CH ServoMaster Installation Manual Page

18 L L5 L L6 L3 L7 L4 L8 COMM NOTE: In some con fig u ra tions it is nec es sary to ex pand the fire alarm panel with more ad dress - able loops This is done by add ing more mod ules There is no room for ex pan sions in the en clo sure of the ba sic fire alarm panel ny ad di - tional mod ules must be placed in sep a rate cab i nets Due to the EN54 reg u la tions, the ad di tional cab i net must be mounted close to the fire alarm panel cab i net so that both cab i nets can be con sid ered as one unit One built-in power sup ply and bat tery can serve three loop con trol ler units () where one is mas ter and two are slaves Each con trol ler serves four ad dress able loops The s are in ter con nected by two ServoLN buses and a backup line Each unit is pow ered from the mas ter power sup ply and battery The operator pan els are con nected to the same ServoLan buses and are pow ered from and V in the Ch and Ch cables 33 Loop Expansion With Collective Loops ServoLan Ch 3 C 8V DC ServoLan Ch ackup Line OP Master FIRE POWER :47 FULT SYSTEM FULT TEST DISLEMENTS SERVOTEKNIKK LRM SOUNDERS DELYED OPERTOR CCESS Local LN CLM Normal operation C DEF GHI JKL MNO PQR 3 STU VW XYZ 4V D V L RS-85/4VDC/L MENU LRMS NEXT LRM LRM SILENCE 0 ServoMaster ddressable loops 3k3 3k3 3k3 3k3 3k3 3k3 3k3 3k3 Collective loops See sec tion 3 for more information on the CLM module oth ad dress able and col lec tive pan els can be ex panded with ad di tional col lec tive loops by us ing CLM 00 mod ules Each CLM mod ule will add 8 col lec tive loops to the panel The end-of-line re sis tance on the col lec tive loops are 5k6 CLM 00 is con nected to ServoMaster panel through a lo cal LN flat ca ble The CLM module is pre pared for TS35-rail mount ing ServoMaster Installation Manual Page 7

19 MENU LRMS NEXT LRM POWER :47 LRM SILENCE FULT SYSTEM FULT TEST DISLEMENTS LRM SOUNDERS DELYED OPERTOR CCESS C DEF GHI JKL MNO PQR STU VW XYZ SERVOTEKNIKK 34 Loop Expansion Up To 3 ddressable Loops 3 C SLVE SLVE 3 SLVE 5 SLVE 7 8V DC CCU D/ Power attery ServoLan Ch ServoLan Ch ackup Line 4V MSTER SLVE SLVE 4 SLVE 6 OP FIRE Normal operation ServoMaster See sec tion 6 for more information on the CCU unit NOTE: CCU 00 charg ing con trol unit must be added to han dle the power dis tri bu tion and bat tery charg ing if a fire alarm panel con tains more than three mod ules Up to 8 mod ules (=3 ad dress able loops) can be con nected to the CCU ll mod ules will be pow ered from a com mon power sup ply and bat tery through the CCU unit ll s and op er a tor pan els are con nected to the same ServoLan buses Ch and Ch and backup line The CCU are con nected to Ch only The power sup ply must give at least 6 at 8 VDC (0 rec om mended) and the 4 V bat tery must have a ca pac ity of min 4 h 0 sup ply can charge a 65 h bat tery The size of the power sup ply and the bat tery should be cal cu lated in ac cor dance with the to tal con sump tion us ing the ServoConfig soft ware tool ServoMaster Installation Manual Page

20 MENU LRMS NEXT LRM LRM FULT SYSTEM FULT TEST MENU DISLEMENTS LRMS LRM SOUNDERS DELYED OPERTOR CCESS NEXT LRM LRM FULT SYSTEM FULT TEST DISLEMENTS LRM SOUNDERS DELYED OPERTOR CCESS MENU LRMS NEXT LRM LRM FULT SYSTEM FULT TEST DISLEMENTS LRM SOUNDERS DELYED OPERTOR CCESS 35 Distributed Fire larm Systems FIRE POWER :47 SERVOTEKNIKK 3 C 8V DC 3 C 8V DC FIRE POWER :47 SERVOTEKNIKK Normal operation SILENCE ServoMaster 4V Power Group MSTER 4V Power Group 4 OP OP 3 D D SLVE Normal operation SILENCE ServoMaster ServoLan Ch ServoLan Ch ackup Line Power Group 3 C 8V DC D D 3 C 8V DC D D 4V SLVE SLVE 3 SLVE 4 FIRE Normal operation POWER : SERVOTEKNIKK CCU D OP SILENCE ServoMaster 4V Power Group 3 SLVE 5 SLVE 6 In some cases it might be con ve nient to split the fire alarm sys tem into smaller panel units placed on var i ous lo ca tions in the build ing or in the ves sel This will save ca ble cost as each loop ca ble only have to be pulled to the clos est panel unit and not all the way back to a cen tral ized fire alarm panel Even if the sys tem is di vided into sev eral cab i nets in dif fer ent lo ca tions, they are still to be con sid ered as one sys tem This means that a dis trib uted so lu tion can con tain up to 3 ad - dress able loops For safety rea sons, each dis trib uted cab i net must have a sep a rate con nec tion to the mains sup ply and a sep a rate set of backup bat ter ies Each phys i cal unit can there fore be de fined as a power group The in ter con nec tion be tween each power group is done via two screened 3-core ca bles (ServoLN Ch & Ch ) In ad di tion it is rec om mended to pull one backup line (L) con tain ing a sin gle core ca ble 4V 30 VC 8 VDC 30 VC POWER GROUP POWER GROUP 4V 8 VDC T TT RTN CHG PS ServoLan CH CH L GND L V D V D T TT RTN CHG PS ServoLan CH CH L GND L V D V D L CH CH ServoMaster Installation Manual Page 9

21 4 DDRESSLE LOOP DETECTORS ll ad dress able sen sors are con nected to a screened -wire loop which is ter mi nated in both ends in a ServoMaster unit Each ad dress able loop can han dle up to 7 sen sors, which gives a max i mum of 508 ad dress able sen sors on one One sys tem can con tain max 3 loops, this gives a max i mum of 4064 sen sors ll sen sors on ad dress able loops are au to mat i cally given an unique ad dress which is used to iden tify the sen sor when giv ing an alarm or dur ing a fault con di tion 4 UTD 53, Universal Temperature Detector The UTD 53 is used to de tect open fires with or with out smoke de vel op ments The sen sor will give a re sponse when a built-in NTC temperature sensor detects a rise of ambient temperature in accordance with EN specifications or if a specified max temperature is exceeded UTD 53 is avail able in three sen si tiv ity ranges: UTD 53 ac cord ing to EN54-5, class UTD 53- ac cord ing to EN54-5, class UTD 53-3 ac cord ing to EN54-5, class The most im por tant fea tures are: Digital signal processing Fault alarm in the event of com po nent fail ure pre-alarm level SSD 53can be mounted by means of any base in the US 50 se ries, see sec tion 6 4 SSD 53, Scattered Light Smoke Detector The SSD 53 is used to de tect an early stage of smoul der ing fires and open fires with smoke de vel op ment The sen sor is work ing ac cord ing to scat tered light (Tyn dall ef fect) prin ci ple The sen sor will give an elec tri cal sig nal when sus pended par ti cles (smoke) are pres ent in the sam pling cham ber The most im por tant fea tures are: Digital signal processing Fault alarm in the event of com po nent fail ure larm thresh old fol low-up when end-of-range mes sage Warn ing sig nal on soil ing larm fil ter with dy namic lim i ta tions to re duce false alarms SSD 53can be mounted by means of any base in the US 50 se ries, see sec tion 6 43 STD 53, Smoke and Heat Detector The STD 53 is used to de tect an early stage of smoul der ing fires and open fires with or with out smoke de vel op ment The sen sor is work ing ac cord ing to scat tered light (Tyn dall ef fect) prin ci ple com bined with an NTC temperature sensor The sen sor will give an elec tri cal sig nal when sus pended par ti cles (smoke) are pres ent or if there is a rise of am bi ent tem per a ture as spec i fied or if a spec i fied max tem per a - ture is ex ceeded The most im por tant fea tures are: Digital signal processing Fault alarm in the event of com po nent fail ure larm thresh old fol low-up when end-of-range mes sage Warn ing sig nal on soil ing larm fil ter with dy namic lim i ta tions to re duce false alarms ServoMaster Installation Manual Page

22 SDT 53can be mounted by means of any base in the US 50 se ries, see sec tion 6 L Sc Sc Remote lamp RL - ase US Detector series 53 Connection for UTD, SSD and STD sensors 44 MCP 545, Manual Call Point The man ual call point is used to give fire alarm if a thin glass plate in the front of the box is bro ken The unit will give a fault alarm in case of com po nent fail ure MCP 545 is avail able in three hous ings: MCP 545- with out hous ing for flush mount ing or housed in op tional sur face mounted SR box, pro tec tion class IP4D MCP Housed in sur face mounted sealed box, pro tec tion class IP55 MCP Housed in sur face mounted sealed box for en gine rooms and hu mid rooms, pro tec tion class IP67 See hous ing di men sions in sec tion 63 MCP MCP 545- /-3 /-4 - Sc - Sc L Sc Sc ServoMaster Installation Manual Page

23 L SHLD L -L -L DDR LOOP DOOR OPEN SW DOOR CL SW DOOR RELESE UX SUPPLY 4VDC DOOR MGNET SOUNDER 45 FDC 00, Fire Door Controller The ad dress able Fire Door Con trol ler FDC 00 is pri mar ily used to con trol fire doors The unit can also be used to op er ate fire damp ers, shut downs and other func tions trigged by fire alarms The board is housed in a sur face mounted steel box with 6 x PG6 for ca ble en try There are 3 ad di tional blinded open ings pre pared for PG6 glands The unit is con nected to the ad dress able loop (L) as a sen sor There are in lets for door open and door closed sen sors and for man ual NC door re lease The door po si tion is in di cated by a two colored LEDs on the board, yel low in di cates open door and changes to green when the door is closed sounder can be con nected to in di cate door clo sure The door mag net and the sounder must be pow ered by a separate 4 VDC sup ply line Other func tions can be con nected to the door mag net out let FIRE LRM SYSTEM FIRE DOOR CONTROLLER FDC-00 L FDC L SHLD L -L -L DDR LOOP DOOR OPEN SW DOOR CL SW UX SUPPLY 4VDC DOOR MGNET SOUNDER 4VDC ux power supply 4VDC NC DOOR RELESE Manual door release 45 Functional description The FDC 00 Fire Door Con trol ler can be con fig ured to op er ate in sev eral dif fer ent modes de pend ing on the re quire ments of the ap pli ca tion The de sired mode is se lected in the ServoMaster Config pro gram In ad di tion to the pre de - fined con fig u ra tions, the FDC can be cus tomer con fig ured in con fig u ra tion no 9 The ranges allowed for the dif fer ent pa ram e ters are listed in the ta ble No in di cates that the corresponding action is disabled Stan dard fire door op er a tion The sounder out put is ac ti vated when the com mand to close the door has been given The sounder is ac ti vated 8 sec onds be fore the door clos ing is ini ti ated The sounder re mains ac ti vated un til 'door closed' is in di cated There is a 30 sec time out on the sounder out put in case the door is blocked The door may be closed from a man ual clos ing de vice con nected di rectly to the FDC Power to the door mag net out put is re stored af ter the door is deemed to be closed and the man ual clos ing de vice(s) have been re set to the nor mal state In the event that door clos ing has been com manded both cen trally and lo cally, the first oc cur ring event shall take pre ce dence To re store the power to the door mag net out put, a 'Door Open' tele gram from the ServoMaster Installation Manual Page

24 panel must be the last re ceived door com mand In ad di tion, the man ual clos ing de - vice(s) must be re set to the nor mal state ) Door con trol with open and closed door mon i tor ing: When the door open in put is ac ti vated, the FDC will give a 'Door Open' indication ) Door con trol with closed door mon i tor ing: When the com mand to close the door is re set and the Door Closed in put is no lon ger activated, the FDC will give a 'Door Open' indication 3) Close the door if com mu ni ca tion is lost: Same as ) but the door will close au to mat i cally if the com mu ni ca tion with the panel has been lost for 0 sec 4) Quiet door clos ing: Used when no sounder is re quired There will be no 'Door Closed' or 'Door Open' indications 5) Fire damper con trol with open and closed damper mon i tor ing: Same as ), but used when sounder out put and in put for man ual clos ing are not re - quired 6) Fire damper con trol with closed damper mon i tor ing: Same as ) but used when sounder out put and in put for man ual clos ing are not re - quired 9) Cus tomer con fig u ra tion: ll pa ram e ters are selectable within lim its as shown in the table Configuration Sounder Sounder activated Close door af ter Fault mes sage if Send 'door open' activation time while door is comm lost on door not closed if re lay re set and be fore clos ing closing SecuriLine within timeout no 'door closed' door signal No Function Sec / No Yes / No Sec / No Sec / No Yes / No Fire door with open and closed door monitoring 8 Yes No 30 No Fire door with closed door monitoring 8 Yes No 30 Yes 3 s ) but close the door if communication is lost 8 Yes 0 30 No 4 Quiet door closing No No No No No 5 Damper with open and closed monitoring No No No 30 No 6 Damper with closed monitoring No No No 30 Yes 7 Not in use Not in use Customer configuration 0-60 /No Yes / No 0-0 / No 0-0 / No Yes / No Fault in di ca tion The 4VDC aux il iary sup ply is mon i tored by the FDC If the power is lost, the FDC will is sue an 'ux Sup ply Fault' message This fault in di ca tion will not be given if a com mand to close the door was al ready given from the panel at the time when the power was lost When the Door Closed in put is ac ti vated, the FDC will pro vide a 'Door Closed' in di ca - tion If the Door Closed in put is not ac ti vated 30 sec onds (de fault time) af ter the com - mand to close the door was given, the FDC will in di cate a 'Door Sta tus Fault' The local operations of the FDC are not in flu enced if com mu ni ca tion with the con trol panel is lost ny door clos ing com mand al ready re ceived from the con trol panel will be com pleted Door clo sure may still be ini ti ated lo cally through the Door Re lease in put ServoMaster Installation Manual Page 3

25 L L -L -L x x COLL DDR LOOP LOOP SHLD 46 MU 00, Multi Purpose ddress Unit The multi pur pose ad dress unit MU 00 is used to in ter face collective sen sors or switches to an ad dress able loop The MU mode -4 should be cho sen ac cord ing to the type and number of sen sors and max cur rent in the loop dd the stand-by currents in all planned sensors on the MU collective loop (see the table below) Select the MU mode that is closest to the max sensor current Sen sors con nected to one MU 00 will all be re ported with the MU zone address The MU mode must be con fig ured from the ServoMasterConfig pro gram ac cord ing to the con nected sen sor type and cur rent drain The op er a tion mode, cur rent con sump tion and end-of-line re sis tor de pends on the pro - grammed type Sen sor stand-by current Type Detect m IRM 3 Smoke 00 KR, KSR Manual 00 SSD 5 Smoke 0 STMV-70 Thermal 005 UTD 5 Heat 05 UFM 840 Flame 30 STU-904 Timer 00 DDRESS UNIT MU-00 DDRESSLE FIRE LRM SYSTEM MU mode pplication Max sensor current EOL 3) resistor Pulsed operation Signal type Collective loop <09 m 09 m 39k NO larm Collective loop m ) 04 m 7k NO larm 3 Collective loop m 093 m k NO larm 4 Collective loop m 99 m 5k6 NO larm 5 Flame detector UFM 840 ) 4 m N NO larm 6 Limit switch N 39k YES Message 7 Toggle switch (impulse) N 39k YES Message 8 Door monitoring switch N 39k YES Message 9 Inductive sensor 00 m N YES Message 0 ddressable sounder 0 m N YES Output ) Zener arrier ( Ohm) can be used in mode, max current = 039 m ) The Timer Unit can be used in mode 5 (See section 593) 3) EOL color code: 39k = or ange-white-or ange (5%) or or ange-white-black-red (%) 7k = red-vi o let-or ange (5%) or red-vi o let-black-red (%) k = brown-red-or ange (5%) or brown-red-black-red (%) 5k6 = green-blue-red (5%) or green-blue-black-brown (%) Manual Call Points can be used in mode -4 (max 0 / loop) The board is housed in a sur face mounted IP44 steel box with three PG6 glands for ca ble en try The unit is con nected to the ad dress able loop (L) as a sen sor LED in the front of the box in di cates alarm from the sen sor(s) on the col lec tive bus De scrip tion of col lec tive loop and col lec tive loop sen sors is given in sec tion 5 EOL 39k EOL 7k EOL k EOL 5k6 39k 39k 39k IRM MS 30Ex IRM-3 IRM-3 UFM 840 EX RE 3 4 E ZENER RRIER STMV IRM LIMIT SWITCH or STU-904 TOGGLE SWITCH DOOR SWITCH INDUCTIVE SENSOR SOUNDER E Sc KR/KSR KR/KSR KR/KSR max 09 m max 039 m max 093 m max 99 m Sc L L L -L L -L x x COLL DDR LOOP LOOP L -L L -L x x COLL DDR LOOP LOOP L -L L -L x x COLL DDR LOOP LOOP L -L L -L x x COLL DDR LOOP LOOP L -L L -L x x COLL DDR LOOP LOOP L -L L -L x x COLL DDR LOOP LOOP L -L L -L x x COLL DDR LOOP LOOP L -L L -L x x COLL DDR LOOP LOOP L -L L -L x x COLL DDR LOOP LOOP Mode Mode Mode 3 Mode 4 Mode 5 Mode 6 Mode 7 Mode 8 Mode 9 L -L L -L x x COLL DDR LOOP LOOP Mode 0 ServoMaster Installation Manual Page

26 5 COLLECTIVE LOOP SENSORS Col lec tive loop sen sors must be used if the ServoMaster is de liv ered with col lec tive loop driv ers (type 8C), see sec tion and 3, or if a Col lec tive Loop Mod ule, CLM 00 is added to an 4, see sec tion 33 Some of the col lec tive mod ules can be used to - gether with the Multi Pur pose d dress Unit MU 00, see sec tion 4645 The sen sors on a col lec tive loop can not be ad dressed, all sen sors in the loop will be iden ti fied as the loop num ber only 5 num bers are re served for col lec tive loops The max i mum num ber of sen sors in one col lec tive loop is 3 The amount of col lec tive sen sors in a sys tem is al most un lim ited as 7 col lec tive loops will oc cupy the same ca pac ity as one ad dress able loop col lec tive loop is a two-wire ca ble with or with out screen 5k6 end-of-line re sis tor is needed If a multi pur pose ad dress unit MU 00 is used the end-of-line re sis tor value de pends on the pro grammed type, see sec tion SSD 5, Scattered Light Smoke Detector The SSD 5 is used to de tect an early stage of smoul der ing fires and open fires with smoke de vel op ment The sen sor is work ing ac cord ing to scat tered light (Tyn dall ef fect) prin ci ple The sen sor will give an elec tri cal sig nal when sus pended par ti cles (smoke) are pres ent in the sam pling cham ber The most im por tant fea tures are: Digital signal processing Self-check with ac tive fault dis play (LED flashes at Hz) larm thresh old fol low-up when end-of-range mes sage (LED flashes at Hz) larm fil ter with dy namic lim i ta tions to re duce false alarms SSD 53can be mounted by means of any base in the US 50 se ries, see sec tion 6 5 UTD 5, Universal Temperature Detector The UTD 5 is used to de tect open fires with or with out smoke de vel op ments The sen sor will give a re sponse when a built-in NTC temperature sensor detects a rise of ambient temperature in accordance with EN specifications or if a specified max temperature is exceeded UTD 5 is avail able in three sen si tiv ity ranges: UTD 5 ac cord ing to EN54-5, class UTD 5- ac cord ing to EN54-5, class UTD 5-3 ac cord ing to EN54-5, class The most im por tant fea tures are: Digital signal processing Self-check with ac tive fault dis play (LED flashes at 0 Hz) SSD 53can be mounted by means of any base in the US 50 se ries, see sec tion 6 L Sc Remote lamp RL - ase US Detector series ServoMaster Installation Manual Page 5

27 53 MS30Ex, Infra-red Flame Detector The MS30Ex is used to de tect in fra-red ra di a tion pro duced by flam ing fire in volv ing carbonaceous material The sensor is intrinsically safe certified E Ex ia IIc T5 and may there fore be used in haz ard ous ar eas in con junc tion with a zener bar rier 900/, se sec tion 50 The sen sor can be mounted di rectly to a con duit box or re cessed in false ceil ings deck-head mount ing kit with base M300EX can be used damp and dirty en vi ron ments Sc L R - MS30Ex RL - Remote lamp 54 IRM-3/, Ionic Smoke De tec tor The IRM-3/ is used to de tect fires with smoke de vel op ment in dry and hu mid areas The sen sor is work ing ac cord ing to ionic prin ci ple The sen sor will give an elec tri cal sig nal when sus pended par ti cles (smoke) are pres ent in the sam pling cham ber The unit can be mounted by means of three types of base: 43 sur face mount ing in dry areas, pro tec tion ac cord ing to IP4 43UH flush mount ing in hol low ceil ing, pro tec tion ac cord ing to IP4 43VT sur face mount ing in hu mid areas, pro tec tion ac cord ing to IP54 See hous ing di men sions in sec tion 6 Sc 3 Remote lamp - 4 RL L Isolate joint inside unit 5 IRM 3/ 6 L E D ServoMaster Installation Manual Page

28 55 UFM-80/, Digital UV Flame Detector The UFM-80/ is used to de tect the ul tra vi o let ra di a tion from open flames in dry and hu mid ar eas The unit can be mounted by means of three types of base: 43 sur face mount ing in dry ar eas, pro tec tion ac cord ing to IP4 43UH flush mount ing in hol low ceil ing, pro tec tion ac cord ing to IP4 43VT sur face mount ing in hu mid ar eas, pro tec tion ac cord ing to IP54 See hous ing di men sions in sec tion 6 Sc 3 Remote lamp - 4 RL L Isolate joint inside unit 5 UFM-80/ IRM 3/ 6 L E D 56 STMV, Thermal Detector The STMV is used to de tect open fires with or with out smoke de vel op ments in en gine rooms and hu mid ar eas, pro tec tion ac cord ing to IP66 The sen sor will give a re sponse when a built-in NTC temperature sensor detects a specified max temperature STMV is avail able in two temperature ranges: STMV o C alarm temperature STMV o C alarm temperature STMV is mounted by means of base The base is pre pared for up to 6 PG6 ca ble glands, pro tec tion ac cord ing to IP66 Sc Remote lamp RL - L L- STMV-70 /-90 Isolate joint inside unit L P P ø45 P 770 P P P P 60 P P 770 P P P - Holes for PG6 P P 60 P ServoMaster Installation Manual Page 7

29 TRYKK HER PRESS HERE 57 KR, Manual Call Point The man ual call point KR is used to give fire alarm if a thin glass plate in the front of the box is bro ken The num ber of units on one col lec tive loop is un lim ited as KR does not con sume any cur rent in standby mode KR can be mounted in two hous ings: ETT/-P frame for flush mount ing in desk or wall, pro tec tion class IP4D SR3T-P box for on-wall mounting, pro tec tion class IP4D See hous ing di men sions in sec tion 63 ETT/-P KR SR3T-P KR lue lue Sc Red L Sc Sc Red 58 KSR, Manual Call Point The man ual call point KSR is used to give fire alarm if a thin glass plate in the front of the box is bro ken KSR is de signed for sur face mount ing in en gine rooms and hu mid ar eas, hous ing pro - tec tion class IP67 See hous ing di men sions in sec tion 63 The ca bles are en tered through PG35 ca ble glands The num ber of units on one col lec tive loop is un lim ited as KSR does not con sume any cur rent in standby mode See hous ing di men sions in sec tion 63 ETT/-P lue KR Sc Red KSR SR3T-P KR lue L Sc Sc L 3 Isolate joint inside unit Sc Red ServoMaster Installation Manual Page

30 DOOR OPEN DOOR CLOSED TIMER UNIT DISCONNECT TIME PRE-WRNING SIGNL NOT USED PRE-WRNING TIME L -L -L L DOOR DOOR DOOR RELESE CL SW OPEN SW DDR LOOP OFF UX SUPPLY (3C MX) DOOR MGNET SOUNDER -/N / -/N / -/N / S S S3 ON STU STU-904, Timer Unit Typ i cal ap pli ca tion for the timer unit is to avoid false alarms dur ing con trolled smoke, dust or heat de vel op ment, eg car load ing on ferry boats The timer unit is used to dis con nect one or sev eral sen sors in col lec tive and ad dress - able loops The timer must be con nected via an ad dress unit MU 00 to dis con nect ON: - 0 hrs OFF: - 59 min ON: Intermitted OFF: Continuous 4 / 5 min OFF / OFF: OFF / ON: ON / OFF: 8 ON / ON: 30 addressable sensors The sen sors are dis con nected by briefly press ing the switch on the box front, a two-digit dis play shows the short est pos si ble dis con nec tion time The time can be ad justed in steps (-59 sec or -0 hrs) by press ing the switch sev - eral times or hold ing it de pressed for more than sec onds The sensors are automatically re-connected after the preset time re lay con tact is closed dur ing the dis con nected pe riod for ex ter nal warn ing buzzer will sound and the dis play will flash as a pre-warn ing a short time be fore the dis con nected time has elapsed re lay con tact is closed dur ing the pre-warning pe riod for ex ter nal warn ing The pre-warn ing time can be pre set to,, 8 or 30 min The pre-warn ing sig nal can be set to be con tin ues or in ter mit ted The dis con nec tion time can be re-ad justed by press ing the switch dur ing the pre-warn - ing pe riod STU-904 can be re con nected man u ally by press ing and hold ing the switch un til the dis play shows the max i mum dis con nec tion time and con tinue to hold it for 5 sec while the dis play flashes The timer will then re con nect the sen sors STU-904 can be op er ated by an ex ter nal switch Press the switch to start dis con nec tion The time is fixed to 30 min or 6 hrs The unit is op er ated from 4 VDC or 30 VC 59 Disconnection in the end of collective loops VDC Reconnect warning Disconnect warning eol res 5k6 STU VC Ext control switch eol res 5k6 Disconnected detectors L 59 Disconnection in the middle of collective loops VDC Reconnect warning Disconnect warning 30 VC Ext control switch eol res 5k Disconnected detector 3 3 L ServoMaster Installation Manual Page 9

31 593 Disconnection in addressable loops One timer unit con nected to an ad dress able loop via a MU 00 ad dress ing unit can be pro grammed by the con fig u ra tion pro gram to dis con nect any ad dress able sen sor(s) in the en tire ServoMaster sys tem Two timer units can not con trol the same sen sor VDC Reconnect warning Disconnect warning 3 MU L -L -L L x x ddressing unit eol res 39k 3 STU-904 Disconnected detectors according to SW programming 3 30 VC L Ext control switch / , Zener arrier Unit The zener safety bar rier is used to con nect col lec tive Exi sen sors (MS 30Ex) in haz - ard ous ar eas to a con ven tional loop The unit is mounted in a sealed steel box The op er at ing volt age is <5 V and the lines are fused by 60 m The unit is sealed ac cord ing to IP 65 The safety bar rier has Ex class EEx-ia Sc 3 4 L 900/ 3 4 MS30Ex 56,0 ø5,0 75, ,0 - Holes for PG35 - Holes for PG6 5,0 ServoMaster Installation Manual Page

32 6 DETECTOR SES 6 US 50 Series ll bases in the US 50series can be used for the ad dress able sen sors XXX 53 and col - lec tive sen sors XXX 5 Chose a base that suits the mount ing method and en vi ron ment con di tion 6 US 50-, universal base for surface mounting US 50- is used for sur face mount ing on ceil ings in dry and hu mid rooms The unit is in pro tec tion cat e gory IP44 and can be used in rel a tive hu mid ity up to 70% con tinuos or 90% short time at 40 o C 6 US 50-, base for hollow ceiling mounting US 50- is used for flush mount ing in hol low ceil ings in dry rooms The unit is in pro tec tion cat e gory IP44 and can be used in rel a tive hu mid ity up to 70% con tinuos or 95% short time at 40 o C ServoMaster Installation Manual Page 3

33 63 US 50-3, base for humid areas US 50-3 is used for sur face mount ing on ceil ings in hu mid rooms The unit is in pro tec tion cat e gory IP54 and can be used in rel a tive hu mid ity up to 70% con tinuos or 95% short time at 40 o C 64 US 50-4, base for concrete mounting US 50-4 is used for flush mount ing in con crete ceil ings in dry rooms The unit is in pro tec tion cat e gory IP44 and can be used in rel a tive hu mid ity up to 70% con tinuos or 95% short time at 40 o C ServoMaster Installation Manual Page

34 6 6 MOUNTING 060 C 6 43 base series for IRM and UFM detectors 43 is used for sur face mount ing in dry ar eas, pro tec tion ac cord ing to IP4 43UH is used for flush mount ing in hol low ceil ing, pro tec tion ac cord ing to IP4 43VT is used for sur face mount ing in hu mid ar eas, pro tec tion ac cord ing to IP54 PG L PG6 PG6 3 43VT E D 6 ø70 PG6 C 40 C 4 5 L 3 43UH E D 000 ase 43VT PG6 PG6 730 C 35 C 4 5 %%c38 L 3 43 E D C-Cable entry ase 43UH ase ServoMaster Installation Manual Page 33

35 63 Manual Call Point Housings Man ual call point for ad dress able and col lec tive loops can be mounted in three hous - ings ETT/-P frame for flush mount ing in desk or wall, pro tec tion class IP4D SR3T-P box for on-wall mount ing, pro tec tion class IP4D KSR/ MCP-4 sur face mounted sealed box, pro tec tion class IP67 KR / MCP ETT/-P SR3T-P * * Cut out for desk mounting 540 (W) x 400 (H) KSR / MCP ø ServoMaster Installation Manual Page

36 7 INSTLLTION 7 Planning ll ad dress able sen sors con nected to the ServoMaster fire alarm sys tem are self-ad dress - ing Due to the fact that none of these sen sors have to be man u ally ad dressed, the time needed for the in stal la tion should be re duced com pared to in stal la tion of tra di tional sys - tems When the loop is ini ti ated (pow ered up), all sen sors and ad dress units will be ad dressed ac - cord ing to the or der they have been con nected in the loop The ad dresses as signed dur ing the ini ti a tion will later be used for con fig ur ing the sys tem When the loop is mon i tored, the fire alarm panel will not iden tify the sen sors by their pre de fined ad dress, but by the or der they are con nected NOTE: It is of outmost importance that there is an exact match between the order of the sen - sors defined in the configuration program and the actual installation NOTE: The best way to achieve this is to fol low the in stal la tion draw ings with out any de vi a tions The ca bles should be pulled from sen sor to sen sor in the ex act or der as shown on the draw - ings In some cases the drawings may show impossible, difficult or unpractical cable routing This may require that the cables must be routed differently from the drawings In that case it is extremely important that the drawings are corrected ny added or removed sen sors must be reflected in the drawings The as-built drawings will be used as a basis for the configuration of the system If there is a mismatch between the drawings and the actual installation, the commission of the system will be difficult and time consuming efore the installation is started the following documentation should be available and checked: Installation drawings The draw ings must con tain the fol low ing in for ma tion: Place ment of all sen sors and ad dress units Type of sen sor or ad dress unit must be spec i fied Zone num ber and zone ad dress on all sen sors and ad dress units Ca ble rout ing (or der of sen sors) Data sheets for all sen sors, ad dress units, alarm de vices etc Make sure that all elec tri cians are fa mil iar with the equip ment and know how the dif - fer ent units should be con nected Panel draw ings show ing the ter mi na tion of all ca bles in side the panel cab i nets Draw ings show ing the in ter con nec tion be tween ex ter nal mod ules and the fire alarm pan els 7 Cabling 7 ddressable loop ddressable loop 7 6 The ad dress able loops are made as two wire ring loops, where the wires ex its the fire alarm panel on the ter mi nals () and (-) The loop re turns back to the panel on () and (-) ll sen sors and ad dress units must be con nected with cor rect po lar ity We there fore rec - om mend to check the ca ble cod ing or cable col ors and de cide which wire will be used as () and () Make sure that all electricians are aware of the coding The com mu ni ca tion be tween the fire alarm panel and any ex ter nal mod ules are done via RS485 com mu ni ca tion buses (CH and CH) The RS485 is a four wire bus (4V,, D and D-) It is im por tant to make sure that the com mu ni ca tion wires are con nected cor rectly be fore the panel is pow ered up Warning! Wrong connections or reversed polarity on the communication wires may dam age com po nents in the sys tem ServoMaster Installation Manual Page 35

37 7 Collective loop Collective loop 5k6 In col lec tive sys tems, the loops are made with two wires The end of the loop is ter mi nated with an end-of-line re sis tor The terminal is marked and is marked in the panel 73 Communication cable OP Most ex ter nal mod ules are con nected to the fire alarm panel via two sep a rate com mu ni ca - tion chan nels CH CH V D V D SERVOMSTER SENTRL V D V D ETJENINGS- PNEL It is important to make sure that the two channels have different cable routing In case of a fire it should not be possible to destroy both channels The protocol on the communication buses CH and CH is for internal use only These communication buses can not be used to transmit data to external systems like Voyage data recorders, paging systems, telephone exchanges etc 73 Choice Of Cable Sev eral dif fer ent types of cable is used in a fire de tec tion sys tem The qual ity or char ac ter - is tics for each ca ble will de pend on what the ca ble is used for Power cables, cables to alarm devices and magnetic door holders, must have a sufficient cross section to carry the current needed to supply the connected equipment Cables for data communication must have sufficient screening to prevent electromagnetic noise from being picked up by, or transmitted from the fire alarm system 73 ddressable loop cables 5 ohm L ddressable loop L = 57 x Q x R max Note: Screened cables with twisted pairs should always be used 4-wire and multi wire cables should have twisted pairs or twisted quads Minimum recommended cross section is 05mm² Larger cross screen than 5mm² is not recommended due to the terminal sizes in the sen sor bases The total resistance from one end of the cable to the other should not exceed 5Ω The re sis tance must be mea sured on the neg a tive wire be tween and The pos i tive wire - is in ter rupted by gal vanic iso la tors in the sen sors Use the for mula to cal cu late the max i mum ca ble length: L = ca ble length (me ter) Q = ca ble cross-sec tion (mm ) R max = loop re sis tance (Ohm) = 5 The for mula is based upon a max al lowed volt age drop of 75 Vat 50 m maxcur rent Ex am ple: Q = 0,75 mm², R = 5Ω L max = 57 x 075 x 5 = 069 m The length of the loop ca bles should un der no cir cum stances ex ceed 500m 00 ohm L Collective loop L U V D U- ServoLan 73 Collective loop cables There are no re quire ments for screened ca bles in col lec tive loops The loop re sis tance in the col lec tive loops are not crit i cal, but should not ex ceed 00Ω which cor re sponds to more than km 733 Communication cables The ca bles used for con nec tion be tween the fire alarm panel and ex ter nal op er a tor panel mod ules con tains two wires for ServoLan data and two wires for power (eg from the fire alarm panel to an ex ter nal op er a tor panel) Screened ca bles with twisted pairs should al ways be used 4-wire and multi wire ca bles should have twisted pairs The to tal volt age drop at the far end of the power ca bles should not ex ceed V The power loss will de pend on the cur rent in the ca ble, the ca ble length and the cross sec tion of the ca ble ServoMaster Installation Manual Page

38 L = 57 x Q / I Use the for mula to cal cu late the max length of the data out let ca ble: L = Ca ble length (me ter) - Q = ca ble cross-sec tion (mm ) - I = max equip ment cur rent (mp) Ex am ple: One op er a tor panel will con sume a max cur rent of 60 m L max = 57 x 075 / 0,06 = 7 m When sev eral fire alarm pan els are in ter con nected on ServoLan ca bles, ei ther as a dis trib - uted sys tem or a net work sys tem (see sec tion 35 and ), the cur rent trough the power ca - bles are very low since each sys tem have sep a rate power sup plies The ca ble cross sec tion is there fore not crit i cal The total cable capacitance and inductance will influence the communication speed which will limit the ca ble length Con nec tion be tween sub pan els in dis trib uted sys tems are max 500 m 734 Recommended cable types When se lect ing ca bles, the cur rent and re quired ca ble length must be con sid ered ac cord - ing to the above for mu las Keep all cables for the fire alarm panel separated, cables for the different functions must be separate Lines for sen sor loops and alarm circuits can therefore not be in the same cable Cable dimensions mentioned are minimum dimensions Equipment Ca ble Type Dimensions (min) Mains sup ply, 30 VC MPRX x 5 mm at tery connection, 4 V MPRX x 5 mm Cabinet grounding PN x 60 mm larm out lets, Door hold MPRX x 5 mm Con trol out lets, Fault, Fire MPRX (3) x 5 mm Loops (ddr) Marine TCX (I) or MPRXCX x x 0,75 mm screen Loops (Coll) Marine MPRX* ) x 075 mm ( screen)* ) Loops (ddr) Land PFLPx** ) x mm screen Loops (Coll) Land PFLPx** ) x mm screen ackup line TCX (I) or MPRXCX x 075 mm screen Data out let (ServoLan) TCX (I) or MPRXCX x x 5 mm screen *) Even if col lec tive loops nor mally does not need to be screened, rec om mends screened cable to avoid pos si ble elec tro mag netic leak age **) Twisted pair 74 Cable Termination It is rec om mended to use end sleeves on all ca ble ends This will pre vent short cir cuits and earth faults caused by loose ca ble cores In some of the sen sor bases, it is nec es sary to con nect two wires in the same ter mi nal In these cases we rec om mend to use end sleeves de signed for two ca bles ServoMaster Installation Manual Page 37

39 Safe area 3 4 Zener barrier EX area 75 Ground Connections 75 larm panels NOTE: It is im por tant to make sure that the fire alarm panels are prop erly grounded If the cab i net is not mounted di rectly on the bulk head or other con duct ing steel wall, a ground ca ble with min i mum 6mm² should be pulled from the marked ground stud in the panel to a se cure ground ing point s a gen eral rule, the screen of all ex ter nal ca bles should be grounded in the fire alarm panel The ground con nec tion is per formed by tight en ing the con duct ing ca ble glands around the ca ble screen Dis man tle the ca ble, leav ing suf fi cient wire length to reach the con nec tion block Fold back the screen wires over the outer man tle and cut ex ces sive screen length, leav ing approx 5 mm down around the mantle Loosen the ca ble gland nut, push in the ca ble and tighten the nut firmly Make sure a se cure ground con nec tion is es tab lished d dress able loop ca bles must be grounded at both ends leav ing and en ter ing the same cab i net The grounded screen must not be in ter rupted Collective loop ca bles does nor mally not need to be screened, but screened ca bles are rec om mended The screen should be grounded in one end leav ing the cab i net The ServoLan data ca bles should be grounded at both ends leav ing one cab i net and en ter ing an other The ackup line should be grounded at both ends leav ing one cab i net and en ter ing an - other 75 Sensors The ca ble screen should not be grounded out side the panel cab i net Most sen sor bases have ded i cated ter mi nals for screen con nec tion which are in su lated from ground If the sen sor base does not have a screen ter mi nal, the two ca ble screens must be joined by means of a sep a rate twist- or push-in con nec tor Pull out some cores from the screen In su late these cores with a yel low/green col ored tube Cut the re main ing screen cores close to the man tle and insulate the end of the screen with a shrink tube Join the screen cores from the two ca bles ac cord ing to sit u a tion 753 EX area The zener bar rier be tween an ex haz ard ous area and a safe area must be se curely grounded on the safe side only The screen on the collective loop ca ble should be con nected to the same ground terminal The EX loop ca ble on the hazardous side must be screened ac cord ing to regulation This screen must be con nected to the sec ond ary ground con nec tor on the EX side only There must not be any con nec tion be tween the ground in the safe- and haz ard ous ar eas! Sensor labeling The build ing or ves sel is di vided into log i cal ar eas or zones dur ing the plan ning of the in - stal la tion ll sen sors within each zone are given a spe cific ad dress num ber (ref sec tion 7) This num ber is called the zone ad dress The zone ad dress is a given num ber and the ad dress does not nec es sar ily have any re la tion to the or der of the sen sors on the loop The zone ad dress is a five digit num ber XXX YY, Where XXX is the zone num ber and YY is the sen sor number ll sen sors, man ual call points and ad dress units should be la beled with this 5 digit num - ber This is usu ally done by at tach ing a small sticker on the sen sor base The la bel should be vis i ble from the floor level ServoMaster Installation Manual Page

40 8 COMMISSIONING 8 General When the in stal la tion of the ServoMaster is com pleted, it has to be com mis sioned Dur ing the com mis sion ing, the com plete in stal la tion will be tested to ver ify that the sys tem works as in tended C The com mis sion ing of the sys tem should be di vided into the fol low ing parts: Power up Loop ver i fi ca tion Sen sor test Out put test Panel test 8 ServoMasterLink v The fol low ing de scrip tion gives in struc tions how to use the ServoMasterLink pro gram to commission an installation 8 Software download e fore the com mis sion ing can be started, a sys tem con fig u ra tion pro gram must be loaded into the fire alarm panel This con fig u ra tion pro gram con tains all in for ma tion about the in - stal la tion, such as num ber of sen sors con nected, lo ca tion and type of each sen sor, how each out put should re act dur ing alarm, in for ma tion about con nected mod ules etc For more in for ma tion about sys tem con fig u ra tion, please re fer to the ServoMasterConfig man ual PC connector E Code selector In some cases the con fig u ra tion pro gram is al ready loaded when the panel is de liv ered In most cases, the fire alarm panel only con tains a ba sic pro gram for power-up In or der to down load the con fig u ra tion pro gram, the fol low ing equip ment is re quired: PC or PC lap top Serial cable ServoMasterLink pro gram ver sion or later To in stall the ServoMasterLink pro gram, please re fer to the in stal la tion in struc tions de liv - ered with the pro gram Con nect the PC or lap top to the main mod ule with a se rial ca ble to down load the ServoMasterLink program The Main can be iden ti fied by the po si tion of the code se lec tor On the Main the code se lec tor is al ways in po si tion 0 It is not nec es sary change the set tings on the code se lec tor dur ing the down load Power up the fire alarm panel (See sec tion 83) Start the ServoMasterLink pro gram The ServoMasterLink pro gram is lo cated in the folder: C:\Pro gram Files\ServoMaster\ServoMasterLink The start-up win dow will be shown on your screen ServoMaster Installation Manual Page 39

41 To open the con fig u ra tion file choose File Then Open Pro ject File (PRJ) Then Dis trib uted down loading via Mas ter rows to the lo ca tion where the pro ject file is stored Se lect the file and press Open The soft ware will con vert the pro ject (PRJ) file When the PRJ file is suc cess fully con verted, press Download The ServoMasterLink pro gram will then try to es tab lish con tact with the fire alarm panel When con tact is es tab lished, the con fig u ra tion screen will ap pear The up per win dow shows the file name of the con fig u ra tion pro gram that is about to be down loaded The text in red color in di cates the pro gram files that are al ready stored in the fire alarm panel The check boxes in di cate which mod ules will re ceive the new con fig u ra tion pro - gram Press Pro gram to down load the new con fig u ra tion The red text will turn to blue as the dif fer ent mod ules are up dated When com pleted, press Dis con nect f ter some sec onds, the fire alarm panel will be re started au to mat i cally 8 System software ll fire alarm pan els con tain sys tem soft ware This soft ware was loaded dur ing the pro - duc tion of the panel t some oc ca sions may rec om mend to up grade this soft ware The ServoMasterLink pro gram can also be used for these up grades 8 Check cur rent ver sions e fore up grad ing the sys tem soft ware, the cur rent ver sion should be checked This can be done by start ing the ServoMaster Link pro gram and press Ver sions The fire alarm panel must be pow ered and the se rial ca ble con nected 8 Up grad ing the sys tem soft ware The sys tem soft ware for the op er a tor pan els (OP) and the mod ules must be up - graded separately To se lect which one to up grade, press File then ei ther Open Sys tem File (HEX) for the (s) or Open Sys tem File OP (HEX) for the op er a tor panel(s) then choose Distributed downloading via Mas ter rows to the lo ca tion where the sys tem soft ware file is stored Se lect the file and press Open Make sure that the fire alarm panel is pow ered and that the se rial ca ble is con nected to the mas ter The soft ware will then con vert the soft ware file When the HEX file is suc cess fully con verted, press Download The ServoMasterLink pro gram will try to es tab lish con tact with the fire alarm panel ServoMaster Installation Manual Page

42 4 C When con tact is es tab lished, the down load screen will ap pear The up per win dow shows the ver sion of the soft ware that is about to be down loaded The text in red color in di cates ver sion of the soft ware cur rently stored The check boxes in di cate which mod ules that will re ceive the new sys tem soft ware Press Pro gram to down load the sys tem soft ware The red text will turn blue when as the soft ware is down loaded When com pleted, press Dis con nect The fire alarm panel will then start a pro cess to flash the new pro gram This pro cess may take a few min utes It is im por tant to leave the panel will power on un til the flash ing is com pleted When the pro cess is com pleted, the panel will be re started au to mat i cally NOTE: The ServoMasterLink ver sion is only com pat i ble with sys tem soft ware ver sions from 0 or later For soft ware ver sions ear lier than 0, please con tact for pro ce dures how to down load con fig u ra tion files or how to up grade the soft ware FUSES PS 50T TT 50T DH 0T 0T 0T CH 0T CH 0T Local LN / RSQ interface 6 CO TT PS DH 8 0 E NO C NC T RTN CHG NO FULT C NC NO FIRE C NC L L Charger voltage Do not readjust! PC INTERFCE Module address selection CO NC 83 Power up NO C NC TSNS GND L L V CH D V CH D IP IP IP IP L4 L3 NOTE: Dur ing the in stal la tion of the sys tem, all volt age sup plies (both mains and bat tery) must be dis con nected t de liv ery all dip-switches and sys tem con fig u ra tions for the main- and sub pan els and all ex pan sion boards are set by Changes must NOT be car ried out with out pre - ced ing con sul ta tion with When all ca bles (ex cept mains and bat tery) for the com plete fire alarm sys tem are con - nected to the main panel and sub pan els, the sys tem can be started by the fol low ing pro ce - dure: Re move the sup ply and bat tery fuses from the fuse hold ers in the main panel and sub pan els Con nect the 8VDC sup ply (PS)and bat tery (TT) wires to the ter mi nal in lets Mea sure the volt age on the PS and TT ter mi nal in lets Ver ify the volt age and po lar ity In sert the bat tery fuse first and then the sup ply fuse in the fuse hold ers The green POWER lamp is lit and the dis play shows "Nor mal op er a tion", date and time The fire alarm in stal la tion is now in nor mal op er a tion and can be tested ac cord ing to the func tional test pro ce dure If the LCD dis play or any lamps on the front show any op er a tional dis tur bances, fol low the in struc tions in chap ter 9 Fault find ing be fore the com mis sion ing can start 83 Fault messages The first time the panel is pow ered up, a lot of fault mes sages may oc cur It is im por tant to clear all these faults be fore the com mis sion ing is con tin ued For help on how to clear the faults, please re fer to the chap ter 9 - Fault find ing It is im por tant to clear any mes sage caused by short cir cuits and earth faults as they may de stroy parts of the sys tem if they are left un solved over lon ger pe riod of time Since the ServoMaster has a self ad dress ing loop sys tem, it is dif fi cult to give any clear mes sages about fault in the loops at this stage The fol low ing two fault types are used to dis play de tec tor faults: No sen sors con nected This mes sage is shown if the loop is pro grammed to have sen sors con nected but no sen sors are found dur ing power up ServoMaster Installation Manual Page 4

43 Un-con fig ured sen sors This is the num ber of the sen sors that is ac tu ally found in the loop, but were the lo ca tion has not been ver i fied and the zone ad dress have not been stored Eg if a loop is pro grammed to have 65 sen sors, but only 60 is con nected, the fault will be 60 un-con fig ured sen sors This mes sage is also given for sen sors with stored zone ad - dresses that does not ex ist in the con fig u ra tion pro gram Miss ing sen sors When the fire alarm sys tem is pow ered up the sys tem will scan the loop and com pare it with the con fig u ra tion pro gram ll sen sors that are not con fig ured with a zone ad dress or not re spond ing will be re ported as miss ing When all sen sors are re spond ing, the num ber of un-con fig ured sen sors should be ex actly the same as the num ber of sen sors con nected In this case, the panel will not re port any miss ing sen sors For fault-find ing on the loop at this stage, the loop ver i fi ca tion tools (see be low) can be very use ful 84 Loop Verification The sen sors used in the ServoMaster sys tem does not have any phys i cal ad dress switches ll the ad dresses will be set by the soft ware It is there fore very im por tant to ver ify that all sen sors are re spond ing with the cor rect in for ma tion This ver i fi ca tion pro cess will con firm that the sen sors are con nected in the same or der as de scribed in the con fig u ra tion pro gram, which is cru cial for a cor rectly con fig ured sys tem The loop ver i fi ca tion can be car ried out in two dif fer ent ways: From the panel front (rec om mended for small and me dium sized in stal la tions) y us ing the ServoMaster Com mis sion ing soft ware tool (rec om mended for large com - plex sys tems) Loop commissioning ack Set active loop Loop reset Config zone addresses View missing sensors View sensors at wrong position View loop comission alarms 84 Loop verification from the panel front The menus for loop ver i fi ca tion is lo cated un der Ser vice func tions in the ServoMaster menu sys tem n ac cess code is re quired to ac cess this area OK Set active loop Enter module/loop: / Current module/loop number:/ Current timeout 00 OK CNCEL CNCEL 84 Set ac tive loop This menu is used to set a ded i cated loop in ac tive mo dus The loop to be com mis sioned must be se lected in this menu Select Set ac tive loop from the menu and press OK Se lect the loop to be set ac tive by mark ing the line En ter mod ule / loop: / and fill in the dig its The first digit is the num ber of the mod ule where the loop is lo cated The sec ond digit is the loop num ber on this mod ule (-4) Current timeout is used to set the ac tive loop in a spe cial test mo dus The test mo dus time is set in min utes When the loop is in test mo dus, only small amounts of smoke is needed to trig the smoke sen sors It is not pos si ble to trig the fire alarm from a loop in test mo dus ll test alarms will be listed un der Loop commissioning alarms (see de scrip tion be low) The time out is only re quired when you want to make com mis sion ing alarms Oth er wise, the time out is set to zero If, for some rea son you want to exit the test mo dus prior to the set time, you can re-en ter the menu and set the cur rent time out to zero ServoMaster Installation Manual Page

44 Loop reset Current module / loop / Press OK to reset loop OK CNCEL 84 Loop re set The fire alarm panel will scan the loops for sen sors ev ery time the panel is pow ered up Each sen sor will be given a num ber ac cord ing to the place ment in the loop (to pol ogy no) ny cor rec tions that are done in the in stal la tion dur ing fault find ing and com mis sion may al ter the se quence of sen sors y re set ting the loop, the panel will re-scan the loop and as sign new to pol ogy num - bers The panel will only re set the loop that was most re cently cho sen in the Set ac tive loop menu Loop re set will not de lete stored zone ad dresses Configure zone addresses Module loop device Enter sensor number ---/-- Configured Read from loop Type: STD 53 STD 53 Zoneaddr 00/ X-Ref 0 0 Deck 5 MFZ Stbd ft Corridor outside cabin 54 Next ack Store 843 Con fig ure zone ad dresses This is the menu used to ver ify the place ment of the sen sors on the loop This test method nor mally re quires two per sons One will stay at the panel and the other per son will go through the com plete in stal la tion and con firm the place ment of the sen sors It is rec om mended to start at the first sen sor in the loop and fol low the ca ble rout ing through the loop When one loop is com pleted, con tinue with the next Select the Configure zone addresses menu The con fig u ra tion menu will al ways start on the first sen sor in the loop cho sen in the Set ac tive loop menu In this ex am ple the first loop on mod ule no The col umn Configured shows the in for ma tion that is pro grammed into the panel (how it was planned) The col umn Read from loop shows what is ac tu ally in stalled The fire alarm panel will now make the LED on this sen sor to flash One per son should now go to the lo ca tion of this sen sor The fol low ing should be checked: LED is flash ing The lo ca tion cor re sponds with the text in the dis play; in this ex am ple, Deck 5 MFZ Stbd ft Cor ri dor out side cabin 54 The cor rect type of sen sor is used The la bel on the sen sor base cor re sponds with the zone ad dress shown in Config - ured col umn in the dis play Make sure that the sen sor is not mounted to close to the bulk head or wall (min 05 m) Make sure that the sen sor is not mounted close to any ven ti la tion in lets or out lets (min m) If all the above is OK, the op er a tor at the panel may press Store The zone ad dress shown in the Configured col umn will now be trans mit ted to the sen sor and stored Press Next to con tinue to the next sen sor If the above is not OK, the ad dress should not be stored Lo cate and cor rect the fault Re set the loop and re-en ter the Configure zone ad - dresses menu To avoid start ing from sen sor (de vice) one ev ery time you en ter the menu, it is pos si ble to type in the zone ad dress The test will then start from this sen sor Con tinue this pro cess un til the zone ad dress has been stored in all the sen sors on the loop Then con tinue with the next loop un til all loops have been com mis sioned To change to an other loop, en ter the menu Set ac tive loop ServoMaster Installation Manual Page 43

45 844 View miss ing sen sors View unconfigured sen sors View sen sors at wrong po si tion These menus are very sim i lar to the menu Configure zone addresses It is not pos si ble to store zone ad dresses from these menus View miss ing sen sors This menu will show sen sors that are miss ing on the loop View uncon fig ured sen sors This menu will show sen sors which are ac tu ally con nected, but were the zone ad dress has not been stored View sen sors at wrong po si tion This menu will show sen sors with a stored zone ad dress, but lo cated at a wrong to pol - ogy ad dress (the or der of sen sors are wrong) View loop commissioning alarms Mod/loop/dev// ctorder of 0 Enter activation order:-- Configured Read from loop Type: STD 53 STD 53 Zoneaddr 00/ X-Ref 0 0 Deck 5 MFZ Stbd ft Cooridor outside cabin 54 Next ack Store 845 View loop com mis sion ing alarms This menu is use ful if you do not know in which or der the sen sors have been con nected to the loop In or der to use this menu, the loop must be set in test mo dus through the Set in ac tive modus menu Go through the com plete loop and ac ti vate the sen sors one by one by means of test gas, heat or other types of test tools In this mode, the fire alarm panel will not ac ti vate any alarms When a sen sor is ac ti vated, the LED will start flash ing The LED on this sen sor will au to mat i cally be turned off when the next sen sor is ac ti - vated Make notes so you now in which or der you have ac ti vated the sen sors lso make notes about the lo ca tion of each sen sor and the zone ad dress marked on the la bels placed on the base of the sen sors When you come back to the panel, you can en ter the menu and check each alarm: If the zone ad dress, lo ca tion and type is cor rect, the zone ad dress can be stored in the sen sor by press ing Store Move to the next alarm by press ing Next or type in the num ber of the test alarm you would like to check 84 Loop verification using the ServoMaster Commissioning software tool In or der to use the ServoMaster loop Com mis sion ing soft ware tool the fol low ing is re - quired: PC or PC lap top RSQ interface Serial cable ServoMaster Com mis sion ing soft ware The ServoMaster Comm soft ware must be in stalled on the PC For in stal la tion help please re fer to the in struc tions de liv ered with the soft ware 84 Con nec tion and startup Make sure that the power to the fire alarm panel is turned off Con nect the RSQ in ter face in one of the mod ules The RSQ in ter face fits into the 34 pin con nec tor This con nec tor may be in use for other pur poses (Lo cal LN) Re move the ca ble that is con nected, in sert the RSQ in ter face and re con nect the ca ble in the other end of the in ter face card ServoMaster Installation Manual Page

46 Con nect the se rial ca ble be tween the RSQ in ter face and your PC Power up the fire alarm panel Start the ServoMaster Com mis sion ing soft ware The pur pose of this pro gram is to com pare the ac tual in stal la tion with the in for ma tion in the con fig u ra tion pro gram The con fig u ra tion pro gram is stored in a project file Select Existing projects and click on Projects to open the cor rect pro ject file If you have the con fig u ra tion soft ware ServoMaster Config in stalled, the pro ject files are nor mally stored un der: C:\Pro gram files\servomaster\servomaster config\pro jects When your pro ject file is opened, press Next In the fol low ing win dow click on the Connect the communication but ton When the PC is com mu ni cat ing with the fire alarm panel, the in di ca tion Communication is es tab lished will be shown in the lower part of the screen Then press Next 84 Down load via the ServoLink pro gram It is pos si ble to down load the pro ject pa ram e ters from the com mis sion ing pro gram to the ServoMaster if, for any rea son, the pro ject data in the sys tem needs up dat ing Click on the Down load to Servomaster but ton (down left) in any of the mode win - dows NOTE: In or der to avoid con fu sion on the port, dis con nect ServoMasterCommission pro gram by clicking on the 'Dis con nect the com mu ni ca tion' but ton ServoMaster Installation Manual Page 45

47 85 Commissioning Loops The field in the left part of screen shows the con fig u ra tion of the sys tem y open ing the tree you will find the loops con nected to the con trol mod ules (-mod ules) The ap pear ance of the loop sym bols in di cate the loop sta tus ppearance Gray Not Configured Configured Commissioning mode Loop build-up lack Pink Red sign in front of the symbol means that the loop is con fig ured and that the sen sors in the loop may be opened in the tree Se lect the loop you would like to test Then se lect Commissioning mode It is pos si ble to se lect more than one loop When the loop is in com mis sion ing mode, the sen sors on this loop will not trig any fire alarm The smoke sen sors will be come ex tra sen si tive in or der to limit the amount of smoke needed to test the sen sors To con tinue, press c ti vate se lected loop mode ServoMaster Installation Manual Page

48 85 Loop buildup (loop status) y press ing the Re start loop buildup but ton the fire alarm panel will start to build up the loop by read ing data from the sensors The loop buildup win dow is ar ranged in four columns: Col Check ing from / side =, from / side = The check di rec tion will change if there is a break or short in the loop Col To pol ogy ad dress (or der in the loop) Col 3 Sen sor type Col 4 Zone ad dress The in for ma tion is col lected from the phys i cal sen sors on the loop as pro grammed When the loop buildup is com pleted, press Next to con tinue It is rec om mended to check that the loop buildup cor re sponds with the in stal la tion draw - ings If some thing is wrong, lo cate and cor rect the fault, then re start the loop buildup Con - tinue this pro cess un til the loop buildup cor re sponds with the in stal la tion draw ings If, for some rea son it is not pos si ble to cor rect all faults on the loop, it is still pos si ble to con tinue the com mis sion ing It will then be pos si ble to com mis sion only those sen sors that are OK 85 Loop verification (Commissioning) The ta ble in the lower part of the Com mis sion ing win dow re flect the in for ma tion from the Loop Sta tus win dow The 'Re corded Sen sor type' and 'Re corded zone ad dress' are col lected from the real phys i cal sen sors and their po si tion on the loop If the sen sors have not been given any zone ad dress dur ing con fig u ra tion, the zone ad dress will be The 'Re quired Zone ad dress' col umn show the zone ad dress as pro grammed in the con fig u ra tion pro gram ServoMaster Installation Manual Page 47

49 When one zone ad dress cell in the list is se lected, the cor re spond ing zone text and sen sor text are shown un der Zone ad dress info This text can be ed ited if wrong, or en tered if miss ing Con firm any change with OK 85 Zone ad dress ver i fi ca tion The loop ver i fi ca tion can now be car ried out with two dif fer ent ap proaches: op er a tor con trolled mak ing test alarms It is also pos si ble to com bine the two ap proaches if that is more suit able n as ter isk (*) in front of a sen sor num ber in di cate that this sen sor has not been ver i fied Op er a tor con trolled ver i fi ca tion This ap proach re quires at least two per sons If you know the ca ble rout ing, this is by far the fast est and most se cure way of ver i fy ing the loops y click ing a blue cells in the col umn Com mands ac ti vated by, the fire alarm panel will make the LED in the ac tual sen sor flash ing The blue cell is now mar ket OPERTOR This in di cates that the op er a tor has ac ti - vated the sen sor Go to the lo ca tion of this sen sor Check that: the LED is flash ing the lo ca tion cor re sponds with the text in the Zone ad dress info field (zone text and sensor text) the type of sen sor cor re sponds with the draw ing the la bel on the sen sor base cor re sponds with the Re quired Zone ad dress in the ta ble the sen sor is not mounted to close to the bulk head or wall (min 05m) the sen sor is not mounted close to any ven ti la tion in lets or out lets (min m) Make cor rec tions to the Re quired Zone ad dress cell if needed as de scribed be low When all the above is OK, right-click in the Re quired zone addr cell Select Store se lected zone ad dress to the sen sor from the pop-up menu ServoMaster Installation Manual Page

50 Change zone ad dress If re corded zone ad dress does not cor re spond with the re quired zone ad dress or if the zone ad dress is wrong it can be cor rected Se lect the ac tual cell in the Re quired zone ad dress col umn and en ter the cor rect zone ad dress Right-click the cell and se lect from the pop-up menu: Store se lected zone ad dress to the sen sor Se lect this op tion to store the se lected ad dress in the phys i cal sen sor Store all zone ad dresses to its sen sor in the loop Se lect this op tion to store all zone ad dresses in the col umn in their ac tual sen sors This may be con ve nient if the sen sors in the loop are not con fig ured (Re corded zone ad dress = 00000) Trans fer the con fig ured loop zone ad dresses Se lect this op tion to col lect the zone ad dresses stored in the cus tomer pro gram and place them in the Re quired zone addr col umn When all zone ad dresses are stored in the sen sors, the data as re corded in the three first col umns can be trans ferred to the cus tomer pro gram by click ing on the Trans fer to configuration program but ton ll zone text and sen sor text gen er ated by the cus tomer in the Config pro gram or in the Zone d dress info field are stored in a sep a rate tmp file in the Com mis sion ing pro gram There is there fore no chance of los ing data in the cus tomer pro gram when changes are made Con tinue the ver i fi ca tion pro cess un til all sen sors have been ver i fied Then con tinue with the next loop un til all loops have been ver i fied ServoMaster Installation Manual Page 49

51 Ver i fi ca tion by mak ing test alarms This ap proach is suit able if one per son car ries out the com mis sion ing It is also suit able if ca ble rout ing is not ac cord ing to the draw ing or if you do not know the ca ble rout ing Ev ery sen sor is ac ti vated with a test alarm in this ap proach Sensor type Triggered by Note Smoke sen sors Test gas Heat sen sors Heat source Do not over heat FDC-00 Short 'door open' in put fire door con trol lers and 'door closed' in put si mul ta neously MU-00 ad dress units Short x and x at approx Hz Un til LED is lit Man ual call points Spe cial key When a test alarm is trig gered, the fire alarm panel will not give any fire alarms The LED in the sen sor will start flash ing Make notes so you now in which or der you have ac ti vated the sen sors Make notes about the lo ca tion of each sen sor and the zone ad dress marked on the base of the sen sors Check that: the sen sor is not mounted to close to the bulk head or wall (min 05 m) the sen sor is not mounted close to any ven ti la tion in lets or out lets (min m) The or der of the test alarms is shown in the last col umn of the ta ble The test ing or der does not need to be the same as the phys i cal or der on the loop The sen sor that is cur rently be ing tested is marked SENSOR in the blue col umn When you re turn to the Com mis sion ing program, check the zone ad dresses one by one Start with Or der, then, then 3 and so on Check very care fully that the in for ma - tion shown un der Sensor info cor re sponds with your notes from the test If OK, right click in the tested Required Zone addr cell ServoMaster Installation Manual Page

52 Select Store se lected zone ad dress to the sen sor from the popup di a log win - dow the zone ad dress will be trans mit ted to the de tec tor and stored the zone ad dress is also shown in the Recorded Zone addr col umn the as ter isk (*) in the first col umn is de leted This in di cates that the de tec tor has been ver i fied Con tinue the ver i fi ca tion pro cess un til all sen sors have been ver i fied and click on the Transfer to configuration program but ton Then con tinue with the next loop un til all loops have been ver i fied 85 Cor rect ing the con fig u ra tion pro gram Since the ServoMaster com mis sion ing tool is linked with the pro ject con fig u ra tion files, it is pos si ble to make cor rec tion in the con fig u ra tion pro gram di rectly from the com mis sion - ing soft ware The fol low ing changes can be made: Zone ad dresses Type in a new zone ad dress in the zone ad dress cell in the sen sor info field, then press OK Zone text Type in a new zone text in the zone text cell in the sen sor info field, then press OK Note that this will af fect all sen sors within this zone larm point text Type in a new alarm point text in the alarm point text cell in the sen sor info field, then press OK Change the or der of the sen sors on the loop, add and re move sen sors Click on the Configured Sensor list but ton The fol low ing win dow will be shown: Reorganize the loop Insert a sensor Delete a sensor Re num ber the first col umn in the ta ble to change the or der of the sen sors Click on the Reorganize the loop but ton to re or ga nize the sen sors in an in creas ing or der To add sen sors, mark the row where you will in sert a new sen sor and click on the In - sert sen sor but ton To de lete a sen sor, mark the row you will de lete, click on the De lete a sen sor but ton ServoMaster Installation Manual Page 5

53 e aware that the com mis sion ing tool is not able to down load the mod i fied con fig u ra tion files Exit the com mis sion ing soft ware and use the ServoMaster link pro gram to down load the mod i fied pro ject file, see sec tion 8 86 Detector Test If the Loop ver i fi ca tion has been car ried out thor oughly, the de tec tor test de scribed in this chap ter could be can celed We do strongly rec om mend do ing a spot check of ran domly cho sen sen sors This test is nor mally car ried out with rep re sen ta tives from the own ers and the class The num ber of sen sors to be tested must be agreed with those rep re sen ta tives Our rec om men - da tions would be approx 0% of the in stal la tion Dur ing the test each of the cho sen sen sors should be ac ti vated Use bot tled test gas for the smoke sen sors and a heat gun or hair dryer for the heat sen sors (e care ful not to over heat) The man ual call points can be tested with a spe cial key tool Dur ing each test, the fol low ing should be checked: the fire LED on the front panel start flash ing the in ter nal buzzer is ac ti vated the text shown in the dis play of the fire alarm panel cor re sponds with the lo ca tion of the detector the zone ad dress on the de tec tor la bel cor re sponds with the zone ad dress shown in the dis play and on the draw ings If the fire alarm is con nected to a mimic panel, a video graphic sys tem, a pag ing sys tem or a tele phone sys tem, the re sponse on these sys tems should be checked for all the test alarms If the fire alarm sys tem is used to mon i tor the sta tus of fire doors and fire damp ers, ev - ery sin gle fire door and fire damper should be opened and closed man u ally to check the cor rect re sponse on the sys tem The sta tus is nor mally shown on a mimic panel or a video graphic sys tem 87 Output Test Nor mally the fire alarm sys tem have out puts to con trol alarm sound ers, P sys tems, fire doors, fire damp ers, ven ti la tion sys tems and so on It is very im por tant that these func tions are tested care fully We rec om mend to trig ger fire alarms in var i ous parts of the ves sel (at least in ac com - mo da tion and en gine room spaces) in or der to check the re sponse on the out lets If there are alarm bells or si rens con nected to the fire alarm panel, the sound level in the var i ous ar eas should be checked to be in ac cor dance with the reg u la tions If the fire alarm panel con trols the fire doors, it should be checked that all fire doors close prop erly when re leased from the panel 88 Panel Test e fore the fire alarm sys tem is handed over to the cus tomer, we rec om mend to per form a small panel test The fire alarm panel was thor oughly tested be fore it left the fac tory This test is rec om - mended to make sure that the panel has not been dam aged dur ing, trans por ta tion and in - stallation Select Test LEDs and LCD dis play from the panel's main te nance menu and con - firm by Enter Press and hold the LED Test key Ver ify that all LEDs on the op er a tor panel are lit and that the sounder is ac tive If a mimic panel is in stalled, all LEDs should be lit Press and hold the LCD Test key Ver ify that all pix els are al ter nat ing be tween black and white ServoMaster Installation Manual Page

54 4 C E Charging voltage adjust 66-76V Press the ack key to re turn to the Main te nance menu Press all keys on the front panel one by one Check that a short beep is heard for each key Re move one sen sor from its de tec tor base Check for cor rect fault warn ing Loosen one of the ca bles in side a de tec tor base The panel should give a bro ken wire fault warn ing Make a short cir cuit be tween the plus and the mi nus wire in side a de tec tor base The panel should give a fault warn ing in di cat ing the short cir cuit Mea sure the bat tery volt age The volt age should be be tween 66Vand 76Vwhen fully charged at 0-5 o C Re move the bat tery fuse Check for bat tery fault warning Re move the 3 sup ply to the power sup ply Check for fault warning in the pri mary sup ply Use a 50 Ohm re sis tor to make a con nec tion be tween TT or and ground Check for earth fault warning In spect the panel for loose screws, scratches and me chan i cal dam age Dur ing this fi nal test it is al ways wise to give the crew a small in tro duc tion how to op er ate the sys tem They should at least know how to read out alarms, how to si lence the alarms and how to ac cept alarms 89 Yearly Testing nd Servicing The com plete fire alarm sys tem (panel, de tec tors, alarm bells/si rens and con trol func tions) should be tested at least once a year by ap proved per son nel The test is per formed as fol - lows : Per form the LEDs and LCD dis play test, see sec tion 83 Check that all lamps on the front panel are lit Press all keys on the front panel, one by one, and check that a short beep is heard for each keystroke Check that all alarm bells op er ate cor rectly by ac ti vat ing a man ual call point Check all de tec tors vi su ally for faults Each detector has a self check system for fault condition which is indicated by a flashing lamp on the detector (SSD53/5 with Hz and UTD53/5 with 0 Hz) ll manual call points and detectors in each zone must be inspected c ti vate at least one de tec tor or man ual call point in each zone and loop Check that all control functions operate correctly Check the fault warn ing by re mov ing one de tec tor head from its base in each zone Check the bat tery charg ing volt age at the TT ter mi nals The charging voltage is temperature controlled and should not be adjusted as long as it is within the range 66V to 76V at 0 5 o C The bat ter ies must be re placed ev ery four years See de scrip tion in sec tion 93 Re plac ing bat ter ies The test is com plete The POWER LED is lit and the text "Nor mal op er a tion" is shown on the dis play If a non-re pair able fault is de tected, please con tact for qual i fied ser vice ServoMaster Installation Manual Page 53

55 80 Maintenance It is im por tant that the sys tem is al ways fully operative This can be en sured by care ful maintenance and regular tests The fol low ing op er a tions should be car ried out by a per son who is ap pointed and trained to be re spon si ble for the sys tem: 80 Panel En sure that the fire alarm panel is un dam aged and kept clean Make sure that the panel al ways is eas ily ac ces si ble 80 Sensors 05 m min c cu mu lat ing dust or paint in smoke and heat sen sors may cause false alarms If a sen sor is faulty, the LED on the smoke sen sor SSD 53/5 flashes at Hz and the heat sen sor UTD 53/5 flashes at 0 Hz Check the sensors at regular intervals and replace them with new as required Replace malfunctioning sensors as soon as possible See section 94 Make sure that fur nish ing and stor ing etc have not re duced the open space be neath the sen sors to less than 05 me ters If a bilge sen sor is con nected, check the mov able parts of the sen sor and the con nec tion box for cor ro sion of ter mi nals 803 Manual call points En sure that man ual call points are not painted over, dam aged or dusty Check the glass cov ers of all man ual call points Replace broken or removed glass covers immediately Make sure that all call points are vis i ble and eas ily ac ces si ble 804 larm units En sure that all alarm bells, si rens, and alarm lights are un dam aged and clean Test them reg u larly 805 Function test ll com po nents must be in or der before the func tion test com mences Refer to section 83, 'Functional test' ServoMaster Installation Manual Page

56 4 C 9 FULT FINDING FULT SYSTEM FULT ny faults must be cor rected im me di ately Use the fol low ing pro ce dures for lo cat ing and cor rect ing faults: 9 System fault The fire alarm panel is non-func tional! The FULT and/or SYSTEM FULT indicators are lit Take immediately contact with the manufacturer or his representative for repair PS 5 T TT 5 T TT PS E 9 Supply fault Check the sup ply volt age at the PS ter mi nals U = 8VDC Check the sup ply fuse (PS) 50 T (5x0mm) and the sup ply ca bles to the panel If these points are in or der, the fault may be in ter nal, and the cir cuit board must be re - placed If the panel is supplied from an external 4 VDC supply through a CCU00 DC/DC converter, check the converter input voltage (-8 VDC) and the converter output 66-76V 8V voltage (nominally 3 VDC) See CCU00 description section 6 93 attery fault Check the charg ing volt age at the bat tery poles it should be within the range of 66 to 76 Volts Check the bat tery fuse (TT) 50 T (5x0mm) and the bat tery ca bles in the panel If these are in or der, the fault may be in ter nal and the cir cuit board must be re placed NOTE! 93 Replacing the batteries Open the panel front by re mov ing the four bolts Dis con nect the power sup ply ca bles from the PS in let and re move all wires from the bat tery poles Ob serve and note the col ors and po si tions of the wires! Re move the bat tery bracket by re mov ing the screws and spring wash ers (use a mag - netic screw driver), and lift the com plete unit with bat ter ies out of the cab i net e care ful not to short cir cuit the bat ter ies! In stall the new bat ter ies into the bat tery bracket with the poles point ing out wards and to wards the cab i net bot tom Fas ten the com plete unit in the cab i net with screws and spring wash ers e care ful not to short cir cuit the bat ter ies! Con nect the bat tery poles ex actly as noted Re con nect power sup ply ca bles Press the Menu <> larm but ton and en ter the ac cess code (if valid) Select the Main te nance menu and Test LEDs and LCD Ver ify that all LEDs are lit Mount the panel front by plac ing the front on the cab i net and fas ten it with the bolts 94 Sensor fault fault in a sen sor is shown on the dis play as a fault warn ing with sen sor ad dress (five dig - its) and a text stat ing the lo ca tion ServoMaster Installation Manual Page 55

57 4 C C Remove the sensor (detector / manual call point / addressing unit) and insert / mount a new one Reset the panel and check the function of the sensor 94 Replacing sensors faulty sen sor on an ad dress able loop can be changed while the loop is ac tive Re move the faulty sen sor from its base by turn ing the sen sor coun ter clock wise In sert a new sen sor within 40 sec to avoid fault warn ing, Miss ing sen sor Wait 3-5 sec for the red sen sor in di ca tor light The light will be on for -3 sec while the sen sor is au to mat i cally con fig ured The sen sor is now con fig ured and rec og nized by the sys tem and put into ser vice For mass re place ment of sen sors, con tact the ser vice re spon si ble DH T T T 6 TT 8 0 E - DH - - L L DH - - E 95 Ground Fault ground fault is likely to oc cur out side the panel The fol low ing method of elim i na tion is used to lo cate the fault: One or more of the fol low ing ca bles may have a re sis tance less than kω to ground: at tery pole (TT) or Loop ca bles (L-4) or larm bell out let (-) or Door hold out let (DH-) or larm in put (IP-) Re move the wires for De tec tion loop (L) and press cknowledge If the fault dis - ap pears, the faulty out let is found IP IP IP IP L4 L3 Re peat for Loop, 3 and 4 (L/3/4), Input and (IP-), larm bells and (/), and Door Hold (DH) If these are in or der, the fault may be in ter nal, and the cir cuit board must be re placed 96 larm ell Outlet Fault Check the T fuses and n alarm de vice con nected with wrong po lar ity will cause a fault in di ca tion Verify correct polarities Re move the alarm out let ca bles from the ter mi nals and Connect a 0 kohm resistor over the terminals and reset the panel If the fault reappears, the circuit board must be replaced If not, continue to next point Mea sure the cir cuit re sis tance and note the value Reverse the polarity and measure the resistance again The highest value is used If the measured re sis tance is more than kohms, there must be a break in the ca bles or a poor con nec tion If the re sis tance is less than 9 kohms there is prob a bly a short circuit ServoMaster Installation Manual Page

58 97 Fault On Door Hold Outlet fault in the Door Hold out let (DH) is shown in the dis play with type of fault and fuse num ber (ca bles are not mon i tored) Re place the T fuse DH and re set the panel L L L4 L3 L L 98 ddressable Loop Fault fault in an ad dress able loop is shown on the dis play as a fault warn ing with loop num ber <5 - L4 L3 <00 IP IP IP IP L8 L7 L6 L5 and a text stat ing type of fail ure eg bro ken wire or short cir cuit Remove the loop wires from the terminals (L-4) in the main panel and measure the resistance on the negative wire between and The max loop resistance must not exceed 5 Ohms The positive wire - is interrupted by galvanic isolators in the detectors The fol low ing pro ce dure may be ap plied to pin point the lo ca tion of a ca ble break: Con nect the loop to the panel with one wire pair only (eg to the up per and ter - minals) Re set the panel and note the de tec tor fault warnings Con nect the loop us ing the other wire pair, the lower and ter mi nals Re set the panel and note the de tec tor fault warnings Lo cate the ca ble break by com par ing this in for ma tion with the com plete loop draw ing 99 Collective Loop Fault Re move the loop ca bles from the L- L8 terminals - 0k 5k6 Connect a 5k6 ohm resistor across the and terminals and reset the panel If the fault reappear, the circuit board must be replaced If the fault does not reappear, continue to next point Short the end-of-line re sis tors Measure the resistance in all loops The resistance should not exceed 00 Ohms The fault may be due to a broken wire or bad connection 90 larm Input Fault Remove the cables from the IP and IP terminals Connect a 0 kohm resistor across the terminals and reset the panel If the fault reappear, the circuit board must be replaced If the fault does not reappear, continue to next point Short the end-of-line resistors Measure the loop resistance The resistance should not exceed 00 Ohms The fault may be due to a broken wire or bad connection ServoMaster Installation Manual Page 57

59 9 Communication Error com mu ni ca tion er ror may oc cur both in side the main panel and be tween the main panel 4VDC V CH D V CH D and ex ter nal equip ment The dis play shows the type and the lo ca tion of the er ror In ter nal er rors must be cor rected by a ser vice en gi neer from Check the T fuses CH and CH If an ex ter nal er ror is de tected, check the ca bles be tween the main panel and the equip - ment for cor rect volt age (4 VDC) and bad con nec tions Re set the panel by press ing the key c knowl edge when the fault is de tected and cor - rected 9 Fault On Relay Coils fault on a re lay coil is shown on the dis play with type of fault and type of re lay These faults can only be corrected by a service engineer from the manufacturer 93 Spare Parts Rev for ServoMaster rt No Type Description Main addressable board operating unit 758 4C Main collective board connection unit 7500 Power Supply fuse (PS) 50T (5x0mm) 750 attery fuse (TT) 50T (5x0mm) 7500 larm outlet fuse (-) 0T (5x0mm) 7500 Door magnet fuse (DH) 0T (5x0mm) 7500 ServoLan fuse (CH-CH) 0T (5x0mm) 75 End-of-line resistor 5k6 Ohm, ¼ W 75 End-of-line resistor 0k Ohm, ¼ W 753 End-of-line resistor k Ohm, ¼ W 754 End-of-line resistor 7k Ohm, ¼ W 755 End-of-line resistor 39k Ohm, ¼ W 7530 Circuit board, SM-0090 main PC for ServoMaster 7530 Circuit board, OP-030 main PC for Operator Panel 7540 Plug, pol MST 5/ -ST-508 for Plug, 3 pol MST 5/ 3-ST-508 for Plug, 4 pol MST 5/ 4-ST-508 for Plug, 6 pol MST,5/6-ST-5,08 for FDC 7540 Plug, 0 pol MST 5/0-ST-508 for and OP 7544 Plug, 4 pol MVSTW,5/4-ST-508 for CCU 7545 Plug, 5 pol MVSTW,5/5-ST-508 for PCU 7546 Plug, 6 pol MVSTW,5/6-ST-508 for CLM, MPD and PFR 7548 Plug, 8 pol MVSTW,5/8-ST-508 for MSO OG PCU 754 Plug, pol MVSTW,5/-ST-508 for PFR 7548 Plug, 8 pol MVSTR,5/8-ST-508 for CLM Plug, pol PC 4/-ST-76 for CCU Scotchlok 560 IDC tap connector Power connection for MSO 0565 Mounting rail for add-on modules in standard control panel ServoMaster Installation Manual Page

60 0 TECHNICL DT TLES r ti cle no 0 ServoMaster Modules Type Description Dim HxWxD mm Wgt g Temp o C IP Standby m 00 SM ServoMaster, addressable loops 37 x 300 x 36 5 kg SM 4 ServoMaster, 4 ad dress able loops 37 x 300 x 36 5 kg SM 8C ServoMaster, 8 col lec tive loops 37 x 300 x 36 5 kg Main Con trol Unit, ad dress able loops x 9 x *) Main Con trol Unit, 4 ad dress able loops x 9 x *) C Main Con trol Unit, 8 collective loops x 9 x *) OP Operator Panel, single hight 37 x 300 x *) OP Operator panel, double hight 37 x 600 x *) CCU 00 Charging Con trol Unit 77 x 3 x *) CLM 00 Collective Loop Module 77 x 78 x *) MPD 00 Mimic Panel Driver Module 77 x 78 x *) MSO 00 Monitored Sounder Module 77 x 78 x *) PFR 00 Potential Free Relay Module 77 x 78 x *) 5 5 *) To be en closed in an IP30 rated cabinet larm m r ti cle no 0 Sensors Type Description Dim HxWxD mm Wgt g Temp o C IP Standby m D DRESS LE LOOP SENSORS 7007 FDC 00 Fire Door Controller 30 x 75 x MU 00 Multifunction d dress Unit 5 x 96 x MCP 545- Man ual Call Point, wo housing 87 x 87 x D MCP Man ual Call Point, surf mount box 0 x 3 x MCP Man ual Call Point, surf m sealed box 70 x 3 x SSD 53 Scat tered Light Smoke Detector 675 x 8 ø *) STD 53 Smoke and Heat Detector 675 x 8 ø *) UTD 53 Universal Temperature Detector 675 x 8 ø *) COLLECTIVE LOOP SENSORS 700 IRM-3/ Ionic Smoke Detector 75 x 80 ø **) KR Man ual Call Point 87 x 87 x D KSR Man ual Call Point 70 x 3 x MS30Ex Infra-red Flame Detector ***) 745 x 03 ø SSD 5 Scat tered Light Smoke Detector 675 x 8 ø *) STMV Thermal Detector 77 x 77 x UFM-80/ Dig i tal UV Flame Detector 75 x 80 ø **) UTD 5 Universal Temperature Detector 675 x 8 ø *) STU-904 Timer Unit 30 x 75 x *) IP4 when used with base US 50- or US50- IP54 when used with base US 50-3 **) IP4 when used with base 43 or 43 UH IP54 when used with base 43VT ***) Complies with intrinsically safe certification E Ex ia c T5 larm m ServoMaster Installation Manual Page 59

61 r ti cle no 03 Devices Type Description Dim HxWxD mm Wgt g Temp o C IP Standby m LRM SOUND ERS ND LIGHTS 7060 MF-6WE/4 larm ell 50 Ø x MS-64 larm ell 50 Ø x SEC-99 larm Siren, programmable tone 63 Ø x N WR 4 larm siren, programmable tone 30 x 30 x LT larm siren 86 x 86 x SON6 larm si ren with light 70 x 86 x KT-75/400 ir ty phoon, mag net valve type 5 Ø x * L 04 larm light 86 x 86 x WSR Flash light 4 x 0 x DOOR MG NETS 7045 GPT-G Door mag net w holder, 650N 6 x 65 x (450) Door mag net w holder, 000N 45 x 8 x (5675) Door mag net w holder, 300N 45 x 8 x (5675) larm m ZENITEL NORWY S wwwzenitelbiz css@zenitelbiz