Leaks monitoring systems CPTML01 series AT39102

Transcription

1 Leaks monitoring systems CPTML01 series AT39102 INSTALLATION AND USE MANUAL _ PUBLIC CODE AT02301MI REV. 21 BY 11/16

2 Index INTRODUCTION 3 GENERAL WARNINGS 3 MARKING (INTRINSECALLY SAFE VERSION) 3 REQUIREMENTS CONCERNING THE INTRINSIC SAFETY EQUIPMENT 3 DOCUMENT DESCRIBING THE INTRINSIC SAFETY SYSTEM 3 INTRINSIC SAFETY SYSTEM DIAGRAM 4 DESCRIPTION OF PRODUCT 4 MAIN COMPONENTS 5 INSTALLATION 6 ELECTRICAL CONNECTION SENSORS AND ACCESSORIES 9 ELECTRICAL CONNECTION OUTPUT 13 GSETUP 14 OPERATING 16 ALARM SIGNALS TEST 18 SMS MANAGEMENT 18 CPT09012/I/A INTRINSICALLY SAFE BARRIER CONFIGURATION 18 SENSORS 19 ACCESSORIES 21 OPTIONS 22 SPARE PARTS 23 ACCESSORIES FOR THE SYSTEM 24 EXAMPLE OF APPLICATION 24 EU DECLARATION OF CONFORMITY 25/27/29/31 For information requests and technical assistance contact the freephone number (from Monday to Friday 8:00-12:00 / 13:00-17:00) NB: Within its respect for its quality commitment, Assytech S.r.l. reserves the right to vary or modify its products and the data included in the following manual. This catalogue must not be reproduced, even partially, without prior authorization. Installation and use Manual CPTML01 System PAGE 2

3 INTRODUCTION The manual provides all the necessary instructions for the installation and use of the leaks monitoring systems. GENERAL WARNINGS Before operating on this equipment, carefully read the instructions contained in this manual. The manufacturer cannot be held liable for any operations performed but not included in this manual. In the event of faults or malfunctioning of the instrument, please exclusively contact the company authorized to perform the maintenance or the manufacturer directly. The manufacturer declines all responsibility for any damage to people and/or items resulting from failure to observe the safety instructions. It is considered that all operators of the equipment are aware of the safety regulations relative to the product described in this manual. In the event of any doubts on the operation of the instrument, please exclusively ask the company authorized to perform the maintenance or Assytech directly for instructions. Any tampering with the instrument holds the manufacturer harmless from all responsibility towards the competent bodies. Caution! This product is used on fuel tanks and in environments at risk of explosion and fire. Tanks with underground leaks can cause severe damage to the environment and to people. MARKING (INTRINSECALLY SAFE VERSION) II (1) G [Ex ia] IIC T4 The equipment complies with the essential safety requirements of the following EU directives:: 2014/34/EU 2014/30/EU 2014/35/EU Its construction is in accordance with the following rules: EN EN EN REQUIREMENTS CONCERNING THE INTRINSIC SAFETY EQUIPMENT The electronic equipment contains the Ex barriers and is part of an intrinsically safe system. It must be installed outside the hazordous area and maintained in accordance with the intrinsically safe systems standards EN and maintenance standards EN , or with other national standards. The sensors, described in the manual supplied with the unit, can be installed in hazardous areas. All connections must be made in accordance with the provisions of standard EN , as indicated by the wiring diagrams supplied with the equipment. No changes to the wiring is not permitted without prior authorization from the manufacturer. Connect the ground wire to the terminals provided. Before powering the equipment, make sure that the supply voltage values correspond to those indicated on their circuit diagrams or the user manual. Before carrying out any work, disconnect power supply to prevent any damage to operators or arcing or sparking. Remove the main power supply before opening the power supply boxes of electronics. The spare parts used must be exclusively those provided by the manufacturer. DOCUMENT DESCRIBING THE INTRINSIC SAFETY SYSTEM The standard EN defines an "electrical system intrinsically safe" as an assemled set of interconnected electrical apparatus, which must be described in a "Document describing the" system, in which the circuits (or parts of circuits) to be used in a potentially explosive atmosphere, are intrinsically safe circuits. On this document, the charged project designer, through the knowledge of the electrical parameters: intrinsically safe certified devices associated certificated electric devices non-certified simple apparatus (electrical) the connection wires Installation and use Manual CPTML01 System PAGE 3

4 must ensure and declare, under his own responsibility and without any ambiguity, that the storage limits of the intrinsic safety features of the system are not exceeded. In the practice, this plant system analysis, has the aim to define the maximum length of the connection cables, depending on the characteristics of the cables themselves and of the associated apparatus, in order to ensure, in any considered condition, the intrinsically safe protection for the whole system composed of sensor / cable / Ex-i barrier. INTRINSIC SAFETY SYSTEM DIAGRAM The Ex equipment (sensor) can also be identified as "simple electrical construction", (S.A) if that meets the requirements in the standards EN and may not be certified by an Atex Notified Body if it lacks its own ignition sources. DESCRIPTION OF PRODUCT The system allows the management of up to 28 inputs (tanks, pipelines, wells and tanks dispensers), 8 of which are intrinsically safe. Thanks to the advanced technologies of the software, the system can be configured to perform different functions (monitoring, reporting, alarm etc.), according to the characteristics and needs of the system. The AT39102 control unit is enclosed in a metal container wall; is able to interface to a remote system, and its basic version allows the management of 4 inputs for sensors and 4 relays. Note: the AT39102 control unit can also be programmed using a special software installed on a PC and connected to the serial (See chapter: GSETUP) Technical characteristics Voltage VAC 50/60 Hz Barrier Ex-i parameters Max consumption 25 VA N of level sensors 4 20 Tank Pipes Tanks well Type of level sensors Dispensers well Sensors connection ON/OFF BUS RS485 Relays outputs 4 With RS232 / LAN / GSM/GPRS Remote data connection interfaces Operating temperature -10 C +40 C Dimensions 310X95H260 mm Marking II (1) G [Ex ia] IIC T4 (Intrinsically safe version) s AT39102 /N OF SENSORS / SENSOR TYPE /VERSION /4 /8 /12 /16 /20 /IA: Explosion proof /IS: Intrinsically safe /IM: Ex ma IIC IIB IIA Uo = 27,84 V Io = 0,068 A Po = 0,431 W Lo = Co = Inductance / capacitance applicable IIC IIB IIA Lo = 8 mh 30 mh 75 mh Co = 0,084 µf 0,0654 µf 2,16 µf /A: base Installation and use Manual CPTML01 System PAGE 4

5 MAIN COMPONENTS The equipment comprises a feed unit (1), complete with filter network and power supply, from a management main board (CPU) (2) which includes, in addition to the levels of reading and alarm circuit and the serial outputs of control of the various devices associated with it (PCs, printers, etc.), 4 auxiliary inputs, 4 outputs relays and 1 output 12 VDC. No. two additional optional interfaces (3) allow you to manage other 16 inputs. In intrinsically safe version (/IS), 1 or 2 intrinsic safety barriers (4) provide the "intrinsic protection" of any connected sensors (1 for managing up to 8 inputs / 2 for the management of more than 8 inputs). In the Ex-ma version the device can be interfaced to the equipment through a protection circuit (4B) without the use of Zener barriers. Finally there are several different serial interfaces for the connection of the control unit to the remote devices. SCHEDAC.P.U. DISPLAY TASTIERA AREA Ex A CLASSIFIED SICUREZZA INTRINSECA AREA 3 0 CN2 CN1 RX/TX DATA FLOW COPTRON SOC.COOP. Via Industria, Morbegno (SO) Italy DEVICES 1 STATUS + A B - RS485 CLOSE LOOP + CN2 B A - CN3 COM2 COM3 SENSORI COM1 1 J4 J2 SW L In - SENSORE 1 SENSORE 4 SENSORE 6 CN5 CN7 Switch Interruttore 5 SENSORE 2 SENSORE 5 SENSORE 7 POWER ALIMENTATORE SUPPLY SENSORE 3 SENSORE 8 CPTA Cavo di alimentazione elettrico V VAC AC alimentation cable Pos. Component 1 Power supply AT Principal board (CPU) AT inputs expansion AT A Intrinsically safe barrier for 8 Namur ON/OFF 4-20 ma inputs CPT09012/I/A 4B Protection circuit for Ex m sensor AT17511/A 5 Alimentation cable CA Installation and use Manual CPTML01 System PAGE 5

6 INSTALLATION General warnings If mixed with air, flammable vapours can cause explosive atmospheres. This can lead to hazardous areas due to the presence of gases or vapours. Explosions and fires can cause serious damage or even death. The AT39102 control unit is not explosion-proof. Do not install the control unit in a hazardous place. Installation location When choosing the installation location, it must be considered that the AT39102 control unit must be protected against vibrations and extreme climatic conditions (particularly high temperatures, humidity, etc.) which could alter its electric devices. Fixing To fix the control unit to the wall as follows: 1. Fixing the device with 4 plugs from 5 mm 2. Connect the sensors to the terminals as described in the chapter "Electrical connections sensors and accessories" GSM/GPRS modem installation 1. Insert the GSM module into the special dedicated slot 2. Insert the SIM card in the special slot of the GSM modem, following instructions shown on the modem Fessura per inserimento tessera 3. Start the control unit 4. Check the network connection status on the main display: 01 < DIAGNOSIS MENU > 03 GSM Signal: % Electrical connection To make the electrical connection of the AT39102 control unit, proceed as follows. Switch off all the power supply switches on the electric panel. Make the connections between the power supply panel and the control unit using the relevant connectors. To connect to the driving force, use a cable with three conductors of at least 1.5 mm 2 (phase, neutral and earth) suitably protected. The cable to be used for intrinsically safe sensors must be blue. Refer to the rules relating to circuits with Intrinsically Safe protection Protection circuit Protection circuit to be connected to the level switch with Ex ma protection mode. The circuit specifications are indicated in the manual. Installation and use Manual CPTML01 System PAGE 6

7 Installation diagram The system shall be made by specialised personnel. Comply with safety regulations. Read carefully the instructions shown in this manual. Assytech declines all responsibility for damages and/or additional costs incurred if supplied instructions are not complied with. Note A Installation shall be carried out in compliance with CEI 64-8 and CEI EN standards. Note B The cables of the Zener barrier must comply with the provisions of Standards EN and IEC Note C Use cables that comply with provisions stated by regulations applicable in the Country of installation. CEI 64-8: Electric systems for equipment at rated voltage not above 1000 V AC and 1500 V DC. CEI EN (1998) CEI classification Electric constructions for explosive atmospheres in presence of gas. Part 14: Electric systems in places with explosion period for the presence of gas (other than mines). Cable safety prescriptions The sensors are installed in a hazardous areas, where there may be dangerous liquids and/or vapors. A incorrect installation can cause fire and / or explosion. For this reason, carefully observe the following: Read the instructions carefully. The pipes of the sensors must not contain any other circuit. The cables and conductors of the sensors must only enter in their designated locations. The power and signal cables must not enter in the intrinsic safety location of equipment. The low voltage in the control unit is considered intrinsically safe because it is separated from the high voltage. To maintain the safety is necessary that the sensor cables are installed in their own conduits, to be separated from the other pipelines. Installation and use Manual CPTML01 System PAGE 7

8 Wiring installation For the cable positionning, and to seal the connection points, follow these instructions: Use sealed and intrinsically safe cables, preferably in light blue color, with filler, CPT02101 code. Install the cables of the sensors inside the appropriated junction boxes, CPT15901 code. Use suitable cable glands to realize the connection between the sensor cables and the control unit. The cables will join directly to the control unit. Close the cover of the junction box. Connection to control unit Important The wiring must be realized in accordance with CEI 64-8 and CEI EN and in compliance with the precautions indicated in this manual. The maintenance of intrinsically safe circuits must be made in accordance with CEI Input/output cable positioning and identification The I/O terminals used with the devices connected to the control unit must be properly marked to avoid incorrect wiring. Since incorrect wiring can cause malfunction of the unit, it is recommended to identify the physical location and / or the type of device connected to each terminal. Output relay When using output relays, follow the indications below: Do not use relays to control circuits with higher currents than 1 A (resistive load) or for voltages over 24 VCC. Alarm relays cannot be used for process control. Sensors: installation Before starting to install the sensors, ensure that the conductors are arranged correctly to allow the necessary connections. Important To obtain an excellent incoming signal, avoid joins on the lines. The power supply line conduits must be separated from those of the signal lines. Installation and use Manual CPTML01 System PAGE 8

9 ELECTRICAL CONNECTION SENSORS AND ACCESSORIES - Connection of explosion-proof sensors to the control unit inputs - Connection of Ex ma sensors Protection circuit for Ex ma sensors code AT17511/A SHIELD Installation and use Manual CPTML01 System PAGE 9

10 - Connection of intrinsically safe sensors Intrinsically safe barrier for 8 Namur ON/OFF 4-20 ma inputs code CPT09012/I/A - Presence liquid sensors functional diagram Level sensor cod. CPTL07/S-D-B DOUBLE CONTACT DEVIATED CONTACT SIMPLE CONTACT BLACK WHITE RED GREEN BLACK WHITE RED BLACK WHITE RED WHITE BLACK (RED) (*) Installation and use Manual CPTML01 System PAGE 10

11 Miniature level sensor code CPTL07/P BLACK WHITE RED WHITE BLACK (RED) G 1/8" M 27,00 13,00 40,00 4,0 DEVIATED CONTACT SIMPLE CONTACT (*) 27,50 Tank cavity sensor code CPTL07/S/3/A/00/008/05 WHITE RED (BLACK) Gravity-activated leak sensor code AT38902/1-6/M 90 69,25 WHITE BLACK (RED) WHITE BLACK (RED) Installation and use Manual CPTML01 System PAGE 11

12 Optical sensor code AT20901/i blue brown black COLOR BROWN BLUE DESCRIPTION VDC GND Block diagram, vacuum switch and pressure switch Vacuum switch code AT01010 Pressure switch code AT N.A. N.C p 87 COM. Installation and use Manual CPTML01 System PAGE 12

13 ELECTRICAL CONNECTION OUTPUT Installation and use Manual CPTML01 System PAGE 13

14 GSETUP GSetup allows programming control units. GSetup offers various connection modes towards the level control units: RS232/RS485, GSM and Radio. Connect button Select communication channel Control Units connection To carry out the connection to control unit: - Select a communication channel RS232/RS485 or GSM - Select serial COM and press Connect button Select COM Port - Insert the telephon number if GSM communication: - The system connects to and displays the firmware version installed on the control unit Disconnect button Firmware version Disconnect To end the communication with the control unit press the button "Disconnect". Installation and use Manual CPTML01 System PAGE 14

15 Parameters reading To read the parameters of the control unit connected: - Press Read button Read button - The system shows Download complete and displays all parameters configurated on the control unit Write button Parameters writing To insert or modify the values of the parameters of the control unit connected: - Digit the values in the table - Press Write button - Select if to write all parameters or only parameters modified - At the end the system displays Upload completed Data and time uploading To update date and hour of the control unit connected: - Press Data-Time button Date-Time button Installation and use Manual CPTML01 System PAGE 15

16 OPERATING Startup At start up, the display shows: followed by: CONTROL UNIT CPTS04206 R. XX STATUS OK _ i XX = software revision installed (operational condition OK) Any alarms and/or warnings are displayed on the screen sequentially: X/N _ i _ DESCRIPTION _ X= alarm index N = number of active alarms To access the control unit operation menu, use the special buttons. Scroll menu items Scroll submenu items and exit (Esc) Scroll submenu items and confirm (OK) Main menu The main menu displays the status of equipment operation. To access the menu, press P3. 1. The display shows: 01 < DIAGNOSIS MENU > 03 Signal GSM: % 2. Select using keys and the second menu item 02 < DIAGNOSIS MENU > 03 AT command: 3. Select using keys and the third menu item XXXX program cycles 4. Press P2 to exit from Diagnosis menu 03< DIAGNOSIS MENU > 03 Fps: XXXX Advanced Setup To access the menu, turn on the power by holding down the "P4" button. 1. The display shows the first menu item: 01 < SETUP MENU > 03 Modify parameters 1. Press to access to editing parameters < SETUP: PAR. ID XXX > Description parameter XXX Installation and use Manual CPTML01 System PAGE 16

17 2. Select using keys and the parameter with desired ID (XXX) or digit ID with the keyboard (see the parameters table) 3. Press to access to value parameter < ID:XXX XXX/NNN > Parameter value 4. Select using keys and the index XXX of NNN 5. Press to modify the value of parameter using keyboard 6. Press to confirm. The system returns to the previous menu 7. Press to return at select ID parameter menu 8. Press to exit. The display shows: < SETUP: PAR. ID XXX > Descrizione parametro XXX < QUIT SETUP? > YES 9. Press (YES) to exit setup and save data 10. The system shows Attend and than the main menu NO 01 < SETUP MENU > 03 Modify parameters 11. Select using keys e the second menu item 02 < SETUP MENU > 03 Reset parameters 1. Select using keys and the second menu item < DELETE PARAMETERS? > YES NO 12. Press to reset de parameters. The uni twill restart automatically 13. Select using keys and the third menu item 14. Press to exit from menu Exit 03 < SETUP MENU > 03 Easy Setup To access the menu, turn on the power by holding down the "P1" button. 1. The display shows the first menu iem: 01 < EASY SETUP > 38 In. N XX Input type 2. Select using keys and the input XX desired (Barrier input local input, expansion input) (max 36) 3. Select using keys the type of input (pipe/ tank / tank well / dispenser well / silencing /_) 4. Select using keys and the next menu item 37 < EASY SETUP > 38 Language 5. Select using keys the language (italian / english / french) 6. Select using keys and the next menu item 38 < EASY SETUP > 38 Save and exit 1. Press to confirm and exit from menu Installation and use Manual CPTML01 System PAGE 17

18 Parameters tables ID Short Description Description ID000 In.Local Configured [NU:0 INPUT:1 ACK:2] Sets for each of the 20 local inputs the mode of use (not used, input, silencing input) ID001 In.Local Mode [NO:0 NC:1] Sets for each of the 20 local inputs the operation mode between normally open and normally closed ID002 In.Local Type[TUB:0 SER:1 PZ.S:2 PZ.E:3] Sets for each of the 20 local inputs the descriptive ID003 ID004 In.Local Txt Sms Alarms Tel Number ID005 ComPort: Modem Sets COM (1-4) for modem ID006 ComPort: Debug Sets COM (1-4) for debug ID007 ComPort: Setup Sets COM (1-4) for setup ID008 Language [ITA:0 ENG:1 FR:2] Sets the language Sets for each of the 20 local inputs a descriptive different than the default (ID002) Sets to 5 telephone numbers to which will be sent an SMS in case of alarm ID009 ComPort: Barr.CPT09012i Sets COM (1-4) for CPT09012 barrier ID010 ID011 In.Rem. Configured [NU:0 INPUT:1 ACK:2] In.Rem. Mode [NO:0 NC:1] Sets for each of the 20 remote inputs the mode of use (not used, input, silencing input) Sets for each of the 20 remote inputs the operation mode between normally open and normally closed ID012 In.Rem. Type[TUB:0 SERB:1 PZ.S:2 PZ.E:3] Sets for each of the 20 remote inputs the descriptive ID013 In.Rem. Txt Sets for each of the 20 local inputs a descriptive different than the default (ID012) ID014 ComPort: Tplo Sets COM (1-4) for CPT09012/I/A barrier ID015 Telemetry: AccessPointName Sets the Telemetry Access Point name ID016 Telemetry: ServerName Sets the Telemetry Servere name ID017 Telemetry: ID Station Sets the Telemetry ID Station ALARM SIGNALS TEST Holding down for 10 seconds, the P1 button simulates an alarm condition resulting in: switching on of red LED activation of the siren SMS MANAGEMENT The control unit can send a text message to the set numbers (ID004 parameter) each time an alarm is activated and / or restored. Alarm format: "Alarm ACTIVE/RESTORED: ALARM_DESCRIPTION" The unit also responds to the following SMS: _ "Info" responds with the Fw installed and the ID code of the sim _ "Were" responds with a list of active inputs CPT09012/I/A INTRINSICALLY SAFE BARRIER CONFIGURATION Set SW3 according to table: SW3 SWITCH XX00 ADDRESS 1 XX01 ADDRESS 2 XX10 ADDRESS 3 XX11 ADDRESS 4 Installation and use Manual CPTML01 System PAGE 18

19 SENSORS Level magnetic sensors Ex ma CPTL07/S-D-B Minimum level switch. Max. switching voltage Max. switching current Max. switching power AC/DC Cable type Operating temperature Output functions Protection degree Cable output Body material Float material Fixing Execution Main characteristics 28,8 VCA 28,8 VDC 0,5 A 30 VA PVC shielded, standard length 5 m -25 C +60 C Simple (NO / NC depending on how you place the float) / Commutation / Resistive IP68 IP67 AISI 316 stainless steel AISI 316 stainless steel / NBR G 3/8 M G 1/2" M ATEX II 1G Ex ma IIC T6 Ga Ex ma CPTL07/P Miniature minimum level sensor. Main characteristics Max. switching voltage 28,8 VCA 28,8 VDC Max. switching current 0.5 A Max. switching power AC/DC 10 VA Cable type PVC shielded, standard length 3 m Operating temperature -25 C +60 C Output functions Simple (NO / NC depending on how you place the float) Protection degree IP68 Cable output IP67 Body material AISI 316 stainless steel Float material AISI 316 stainless steel Fixing G 1/8M Execution ATEX II 1G Ex ma IIC T6 Ga Installation and use Manual CPTML01 System PAGE 19

20 Gravity-activated leak sensor Ex ma AT38902/1-6/M This sensor allows the presence of liquid to be detected without being inserted into the tank. It operates according to the principle of communicating vessels. Main characteristics Max. switching voltage 28.8 VCA 28.8 VDC Max. switching current 0.5 A Max. switching power AC/DC 10 VA Cable type PVC shielded, standard length 3 m Operating temperature -25 C +60 C Output functions Switch / Switching Protection rating IP68 (Cable output IP67) Container material Brass Support material Galvanized steel Float material AISI 316 stainless steel Execution II 1G Ex ma IIC T6 Ga Optical sensor AT20901/i EEx ib Sensor for detecting the presence of a liquid within the wells, pipes or containment vessels. Main characteristics Voltage 10-18Vcc Consumption <50mA Output Open collector 40mA Operating temperature -20 C-+80 C Pressure 10 bar Material Polysulfone or nylon Execution Eex ib IIB T6 Vacuum switch for internal interstices AT01010/1/00 Trigger depression: calibration mbar AT01010/2/00 Trigger depressure: adjustable as requested -0,05-0,5 bar II 3 G/D S.A. Main characteristics Max load 1 A 24 VCC Max pressure 10 bar Operating temperature -25 C-+55 C Protection degree IP65 Seals Viton Contacts Gold Connection 1/4" BSP Body material Aluminum anodized Sensor without cable Installation and use Manual CPTML01 System PAGE 20

21 Pressure switch for external interstices AT01110/1/00 Trigger pressure: +150 mbar AT01110/2/00 Trigger pressure: adjustable as request +0,05 +0,5 bar II 3 G/D S.A. Main characteristics Max load 0,5 A 24 VCC Max pressure 10 bar Operating temperature -25 C-+55 C Preotection degree IP65 Seals Viton Contacts Gold Connection 1/4" BSP Body material Aluminum anodized Sensor without cable ACCESSORIES Remote alarm AT15507 The alarm can be activated by one of the control unit outputs. Xenon lamp AT17401/A This comprises a signaller with an amber xenon lamp (/A) frequency 1 Hz assembled on the roof of the container, protection rating IP67. Visibility on four sides. Two tone sirene AT08008 Two tone siren Light indicatore AT05909 Red/gresn light / green common anode 12VDC Installation and use Manual CPTML01 System PAGE 21

22 Serial connection kit AT13600/K Kit for connection the control unit to a remote computer for programming and downloading data Modem GSM/GPRS completo di antenna MHz con base magnetica Codice AT06706 Modem GSM/GPRS per la programmazione e la gestione dei dati a distanza. OPTIONS 8 IN control board AT01909 The board allows you to monitor additional 8 digital inputs associated to external events (Example: leak detectors, etc.). Protection circuit for Ex ma device AT17511/A Protection circuit for Ex ma devices but with the aim of limiting the voltage and current to the envisaged limits. Main characteristics Max input voltage 24 V ±5% Fuse 50 ma 250 V 35 A Installation and use Manual CPTML01 System PAGE 22

23 SPARE PARTS 1 SCHEDAC.P.U. DISPLAY TASTIERA AREA A SICUREZZA INTRINSECA 4 0 CN2 CN1 1 + A B - RX/TX DATA FLOW RS485 CLOSE LOOP CN2 SW1 COPTRON SOC.COOP. Via Industria, Morbegno (SO) Italy + B COM2 COM3 COM1 1 J4 J2 3 DEVICES STATUS A - CN3 SENSORI L In - SENSORE 1 SENSORE 4 SENSORE 6 CN5 CN7 Interruttore 6 SENSORE 2 SENSORE 5 SENSORE 7 ALIMENTATORE SENSORE 3 SENSORE 8 2 Cavo di alimentazione elettrico 230V AC CPTA03612 Rif. Codice Descrizione 1 AT24212 DISPLAY OPERATOR 2 AT V 25 W POWER SUPPLY 3 AT I/O CPU 4 AT01909 INPUTS I2C INTERFACE 5A CPT09012/IA INTRINSICALLY SAFE BARRIER FOR 8 I 4-20 ma Namur ON/OFF INPUTS 5B AT17511/A PROTECTION CIRCUIT FPR EX M SENSORS - AT19911 FUSE 500 MA V 250 V 1500 A 5X20 CERAMIC (PACK OF 10) 6 CA POWER SUPPLY CABLE - AT06706 GSM/GPRS MODULE COMPLETE OF MHZ ANTENNA WITH MAGNETIC BASE - AT MHZ ANTENNA WITH MAGNETIC BASE Installation and use Manual CPTML01 System PAGE 23

24 ACCESSORIES FOR THE SYSTEM Gravity-activated leak sensor AT38902/1/M 1 pipe AT38902/6/M 6 pipes Gravity-activated leak sensor to be installed on the bottom part of the sump so as to recover and signal any product leaks. Certifications II 1G Ex ma IIC T6 Ga EXPANSION unit 4 terminals AT21411/3 Expansion for leak sensor for a further 3 monitoring pipes. Flame trap for compensation pipe AT21511 Flame trap to be installed on the manifold vent pipe (if used). Certifications II 2G Ex d IIC Gb Stop valve AT02311 Stop valve to be used on pressurized circuits to prevent leaks of liquid. EXAMPLE OF APPLICATION FUEL DISPENSER BALANCE PIPE CONTROL UNIT CENTRALIZED LOAD FROM 1 TO 8 SENSORS BARREL FLAME TRAP AT21511 CPTA CAVITY SENSOR AT38901/6/M minimum slop of pipes 1% COMPENSATION PIPE EXPANSION MANIFOLD AT21411/4 Installation and use Manual CPTML01 System PAGE 24

25 Via Val D Aosta 169, Talamona (SO) Italy Tel Fax info@assytech.it Sito web: DICHIARAZIONE UE DI CONFORMITÀ PER PRODOTTI O SISTEMI DI PROTEZIONE ADATTI AD ESSERE UTILIZZATI IN ATMOSFERA ESPLOSIVA (ATEX 2014/34/UE) EU Declaration of Conformity of a product or protection system to be used in an explosive atmosphere (Atex 2014/34/EU) APPARECCHIATURA O SISTEMA DI PROTEZIONE : EQUIPMENT OR PROTECTIVE SYSTEM : CPTML01 serie AT39102/XIS - Sistema per il monitoraggio dei serbatoi CPTML01 series AT39102/XIS - Tank Monitoring System GRUPPO / GROUP : CATEGORIA / CATEGORY : II (1) G MARCATURA APPLICATA / APPLIED MARKING : II (1) G [Ex ia] IIC T4 E COSTRUITA IN ACCORDO CON LE SEGUENTI NORME : IS MANUFACTURED ACCORDING THE FOLLOWING STANDARDS : EN :2004 EN :2007 EN :2003 EN : A1 + A2 + A3 EN :2001 CON LA PRESENTE SI DICHIARA CHE L APPARECCHIATURA SOPRA CITATA SODDISFA I REQUISITI ESSENZIALI DI SICUREZZA DELLE SEGUENTI DIRETTIVE UE : WE HEREBY DECLARE THAT THE ABOVE MENTIONED EQUIPMENT COMPLIES WITH THE ESSENTIAL SAFETY REQUIREMENTS OF THE FOLLOWING EU DIRECTIVES : 2014/34/UE (ATEX) 2014/30/UE (EMC) 2014/35/UE (LVD) IL LEGALE RAPPRESENTANTE THE LEGAL REPRESENTATIVE Talamona, 30/06/2016

26

27 Via Val D Aosta 169, Talamona (SO) Italy Tel Fax info@assytech.it Sito web: DICHIARAZIONE UE DI CONFORMITÀ EU DECLARATION OF CONFORMITY APPARECCHIATURA : EQUIPMENT : CPTML01 serie AT39102/XIM - Sistema per il monitoraggio dei serbatoi CPTML01 series AT39102/XIM - Tank Monitoring System E COSTRUITA IN ACCORDO CON LE SEGUENTI NORME : IS MANUFACTURED ACCORDING THE FOLLOWING STANDARDS : EN : A1 + A2 + A3 EN :2001 CON LA PRESENTE SI DICHIARA CHE L APPARECCHIATURA SOPRA CITATA SODDISFA I REQUISITI ESSENZIALI DI SICUREZZA DELLE SEGUENTI DIRETTIVE UE : WE HEREBY DECLARE THAT THE ABOVE MENTIONED EQUIPMENT COMPLIES WITH THE ESSENTIAL SAFETY REQUIREMENTS OF THE FOLLOWING EU DIRECTIVES : 2014/30/UE (EMC) 2014/35/UE (LVD) IL LEGALE RAPPRESENTANTE THE LEGAL REPRESENTATIVE Talamona, 30/06/2016

28

29 Via Val D Aosta 169, Talamona (SO) Italy Tel Fax info@assytech.it Sito web: DICHIARAZIONE UE DI CONFORMITÀ EU DECLARATION OF CONFORMITY APPARECCHIATURA : EQUIPMENT : CPTML01 serie AT39102/XIA Sistema per il monitoraggio dei dei serbatoi CPTML01 series AT39102/XIA Tank Monitoring System E COSTRUITA IN ACCORDO CON LE SEGUENTI NORME : IS MANUFACTURED ACCORDING THE FOLLOWING STANDARDS : EN : A1 + A2 + A3 EN :2001 CON LA PRESENTE SI DICHIARA CHE L APPARECCHIATURA SOPRA CITATA SODDISFA I REQUISITI ESSENZIALI DI SICUREZZA DELLE SEGUENTI DIRETTIVE UE : WE HEREBY DECLARE THAT THE ABOVE MENTIONED EQUIPMENT COMPLIES WITH THE ESSENTIAL SAFETY REQUIREMENTS OF THE FOLLOWING EU DIRECTIVES : 2014/30/UE (EMC) 2014/35/UE (LVD) IL LEGALE RAPPRESENTANTE THE LEGAL REPRESENTATIVE Talamona, 30/06/2016

30

31 DICHIARAZIONE DI CONFORMITÁ UE EU DECLARATION OF CONFORMITY Noi We COPTRON Soc. Coop. Via Industria, Morbegno (SO) - Italy dichiariamo sotto la nostra esclusiva responsabilità che il prodotto: declare under our sole responsibility that the product: Interruttore di livello tipo: Level switch type: CPTL07 al quale questa dichiarazione si riferisce, è conforme alle seguenti Direttive ed emendamenti successivi: Direttiva ATEX 2014/34/UE Direttiva EMC 2014/30/UE Direttiva Bassa Tensione 2014/35/UE to which this declaration relates, complies with the following Directives and further amendments: ATEX Directive 2014/34/EU EMC Directive 2014/30/EU Low Voltage Directive 2014/35/EU La conformità è stata dimostrata sulla base dei requisiti delle norme o dei documenti normativi riportati qui di seguito: EN EN EN EN EN Modo di protezione / Type of protection: ATEX II 1G Ex ma IIC T6 Ga Temperatura ambiente / Ambient temperature: -25 / +60 C Certificato UE di Tipo / EU type approval certificate: IMQ 08 ATEX 017 X Organismo notificato ATEX / ATEX notified body: 0051 The conformity has been demonstrated with reference to the following standards and normative documents: Istruzioni per la sicurezza nell impiego Vedi capitolo Istruzioni per la sicurezza nell impiego riportato nel manuale tecnico. Instruction for a safe use See the Instruction for a safe use as indicated inside the technical manual. Luogo e data di emissione : Place and date of issue: In nome e per conto di Coptron Soc. Coop. For and on behalf of Coptron Soc. Coop. Morbegno (Italy), 12/07/2016 Edoardo Motti