Appendix-A TECHNICAL SPECIFICATIONS:

Transcription

1 Appendix-A Name of work: Design, Engineering, Supply, Erection, Testing, Commissioning of IP CCTV systems at DGVCL SURAT DIVISIONAL STORE and Navsari RSO. Intent of Technical specifications: TECHNICAL SPECIFICATIONS: The basic intent of these technical specifications is to ensure continuous and effective IP CCTV Solution at DGVCL Stores. To have an Enterprise Level Surveillance & Security System, The vendor shall supply and commission an IP CCTV system with the objective to provide high degree of surveillance system for the entire site. The purpose is to monitor & supervise the entire area for security purpose, as well as record and inform officials on unwanted, untoward incidents. It is also essential to have recorded images to be stored at least for min 90 days of all critical area s to facilitate investigations of a reported incidents. The hardware required for the system including servers / NVR s, workstations, monitors, networking components, cables, connectors, conduits, power supplies etc. will be in vendor s scope. It will be the responsibility of the vendor/bidder to make the entire system fully functional as per the specifications. Vendor/bidder shall consider any equipment/devices required to make the system functional if not mentioned herewith. Further, the CCTV system shall be seamlessly integrated with other security systems such as the Access Control Systems & Intrusion Alarm System. Scope of work: The scope of work against these technical specifications includes but limited to turnkey activities associated with Design, Engineering, pre-dispatch inspection, packing, forwarding, transporting to respective location of DGVCL, unloading, physical verification, proper handling and stacking of material, installation, testing, commissioning, performance testing, of IP CCTV system along at DGVCL SURAT DIVISIONAL STORE and NAVSAR RSO. The scope of work under this tender shall consist of design, supply, installation, testing, training & handing over of all materials, equipment, hardware, software applications and necessary workmanship to commission said system with all the required components strictly as per the enclosed tender specifications, design details. The scope also include the supply, Installation & commissioning of any material or equipment including civil works that are not specifically mentioned in the specification. Moreover it is to specifically noted that any other activities whether or not expressly identified above or hereafter but which are required to meet intent of specifications above shall be considered to have been included within sphere of work and the same shall be considered and included in the offered package. Page of 24

2 Operational & normal management training of entire setup will be imparted to at list 3 to 4 persons at each location in co-ordination with IT Department of DGVCL. SYSTEM ARCHITECTURE: Video Management System (VMS) shall be a fully digital IP video surveillance system that brings together in one system a network video recorder (NVR) with sufficient required storage capacity as per the specifications. As a software-based enterprise-level video and data management system, VMS shall provide a single GUI that monitors, records, and offers functionality to deliver the timely, accurate information required for effectively responding to any challenge. OPERATIONAL REQUIREMENTS A. VMS shall provide a single graphical user interface (GUI) to monitor, control and administer digital video surveillance equipment from multiple systems and platforms B. VMS shall include a fully scalable enterprise-class media management system to enable simultaneous live monitoring from multiple stations and be configurable for storage both on and off site. C. VMS shall be configured to store and view images captured by one camera or numerous cameras and monitor connections across an unrestricted number of servers. D. All the Cameras, Software, NVR & accessories equipment s for CCTV Systems shall be of same manufacturer. Page 2 of 24

3 Appendix-B Letter Copy of MAF compliance of Format To, The Chief Engineer (Gen) DGVCL, Corporate Office, SURAT Date: Tender : Sub: Letter of Authorization for Design, Engineering, Estimation Supply, Installation, Testing and Commissioning of system Dear Sir, We understand at M/s , are participating in the tender referred above. We would like to inform that, M/s.: Address: is assured for the following:. Supply of OEM Products 2. Training / Technical Support 3. OEM products supplied by them will be covered under our standard warranty / service policy as applicable at the time of supply. Further, we would like to confirm:. Service support on our products will be offered for a period of five years from the date of supply through M/s in conformity with the prevailing service policy on the relevant products. 2. Items quoted by M/s are part of our Current Product Portfolio. 3. On request recommended service spares list can be provided by OEM for the time period required, which may be ordered along with the main equipment. Thanking You, M/S Sign: Stamp: Page 3 of 24

4 Appendix - C General Requirements of IP CCTV System at DGVCL, Sl. NOTES FOR TENDERERS:-. Manufacturer must provide reference list of installation for similar products/ components. 2. The warranty shall consist of repairing or replacing defective parts for a period of year from the date of supply. 3. Following authorizations for IP CCTV system shall be made available from the manufacturer: Yes / a) Technical compliance to the specifications, this should be vetted by manufacturer for CCTV Product. b) Authorization for participating in the tender on manufacturer's behalf. c) Authorization that the items quoted by the tendered are in production and would be serviceable for at-least 5 years from the date of tender. obsolete products should be quoted. d) to the standards for the products listed. e) Letter from Manufacturer for supporting the system for at least 7 years. f) Approved makes mentioned in tender should have more than 50 employees on rolls in India. g) OEM for the product mentioned in tender should have R & D Facility with greater than 00 employees in India. h) The Manufacturer shall have its own Service center in India for Security Product. OEM should provide the contact details of Responsible Person / escalation matrix. i) OEM shall be registered company in India, existence in country more than 5 years. j) Suggested product should support BACNET Protocol (Central Monitoring Software). k) OEM shall be ISO certified Or should be an SEI CMM Level 5 certified organization l) Networking OEM Must have ISO 900 and 400 certified manufacturing units in India. m) All the Networking components / raw materials used must be RoHS verified. n) Networking OEM must have RCDD certified professional for extending design help. 4. Bidder or SI should have PF code and WCC Policy for their employees. 5. Bidder or SI should have annual turnover of amount Rs. 0 Crore for Financial year Party has to visit & solve the defect within 48 hours any how & has to change spare free of cost within Guarantee period. 7. All the camera s, software & NVR offered should be from the same make & be ONVIF complaint. 8. Bidder should have authorized service center in Gujarat. 9. Suggested system should be scalable and support Centralize Viewing of all the cameras at DGVCL, Surat. Bidders should provide minimum 300 channel license with minimum 20 client facility to view cameras at central location. 0. Suggested IP CCTV system including Camera, NVR, and Centralized Software should support Video analytics features which DGVCL may purchase in Future. Page 4 of 24

5 Appendix-D Detailed Technical Specifications for IP CCTV System requirement at DGVCL Sr.. Description of IP CCTV System.. Fixed IP IR Bullet Camera : Camera Type : IP Outdoor IR Bullet Camera with 32 GB micro SD card.3 Resolution : 280 x 024 pixels and 280 X 720 ( Minimum Illumination : Color: 0.5 F.4 B/W: 0 Lux (IR ON).5 Image sensor: /3 progressive Scan Video Profile :.6 2-profiles simultaneously H.264 high profile, main profile and baseline Iris Exposure Control :.7 Auto mode / Outdoor mode / Manual mode Manual mode : /25~/47,000 seconds.8 Day Night mode /IR Range : 20 Meter IR Distance.9 Lens : 3.3 to 2 mm Varifocal lens Video Compression : H.264, MPEG4 and MJPEG.0 simultaneously (Tri-encoders) Image Resolution : 720P mode: 280x720, 720x576, 320x80, 60fps..3M mode: 280x024, 800x600, 720x576, 25/30fps.2 Video Profile : 64 Kbps to 6 Mbps Profile Setting :.3 Every video profile has Independent CBR/ VBR/ EVBR/ GOP/ Frame rate setting Region of Interest :.4 Max p mode. Editable range.5 Area of Interest: Max. 2 AOI. Editable range Image Setting: AE, AWB; 3D ise reduction; Digital WDR; Color, brightness,.6 sharpness, contrast, Hue; Mirror/Flip; Privacy Masks; Text, time and date overlay; Overlay image on video Streaming : Simultaneously multi-profile streaming; Streaming over UDP,.7 TCP, HTTP, or HTTPS; M-JPEG streaming over HTTP (server push); Controllable frame rate and bandwidth; Constant and variable bit rate (MPEG4/ H.264); Region of Interest (ROI) Audio Encoder : RTSP: G.7 64kbps, G kbps, AAC.8 (option, by request).9 Audio Streaming : One-way or two-way.20 Microphone : External microphone in.2 Audio Output : Adjustable audio gain (Yes / ) Page 5 of 24

6 Network Protocols : IPv4, IPv6, TCP, UDP, HTTP, HTTPS, SMTP, FTP, NTP, DNS,.22 DDNS, DHCP, DIPS, ARP, Bonjour, UPnP, RTSP, RTP, RTCP, IGMP, PPPoE, Samba, ICMP,SNMP Security : Password protection, IP address filtering, HTTPS.23 encrypted data transmission, user access log.24 Users : 8 simultaneous unicast users.25 Supported Interface : ONVIF.26 Event Detection : Intelligent motion detection, audio detection, camera tampering.27 Motion Detection : 0-zone video motion detection with included or excluded options.28 Audio Detection : Audio level 0-00 Camera Tampering : Camera dis-focus / move direction /.29 mask Alarm Events : File upload via FTP or ; File upload via Samba to NAS;.30 tification via , HTTP, and TCP; External output activation; Audio alerting output.3 Video Buffer : Pre- and post- alarm buffering.32 Ethernet : RJ45 0/00/000M auto negotiation.33 Power : 2VDC or 24V AC and PoE IEEE 802.3af Class 3.34 Mount : Wall, ceiling, Pole as required.35 Operating Temperature : -20 Degree C to 60 Degree C.36 Humidity : 0% ~ 90% (non-condensing).37 : CE, FCC and UL Listed Camera Housing & mount: i. Same make as that of camera and suitable for the model number offered as specified by the manufacturer and should be an integrated unit. ii. Shall be compact and indoor / outdoor type as required Connector: RJ-45 0Base-T/00Base-TX/000Base-T; 2VDC power jack; alarm input and output; RS485 (Option Cable); Audio out; External MIC input; Video out; Factory default reset 2.0 Fixed IP IR Dome Camera : 2. Camera Type : IP Outdoor IR Dome Camera with 32 GB micro SD card 2.2 Resolution : 280 x 024 pixels and 280 X 720 ( 2.3 Minimum Illumination : Color: 0.5 F.4 B/W: 0 Lux (IR ON) 2.4 Image sensor: /3 progressive Scan 2.5 Video Profile : 2-profiles simultaneously (Yes / ) Page 6 of 24

7 H.264 high profile, main profile and baseline Iris Exposure Control : 2.6 Auto mode / Outdoor mode / Manual mode Manual mode : /25~/47,000 seconds 2.7 Day Night mode /IR Range : 5 Meter IR Distance 2.8 Lens : 3.3 to 2 mm Varifocal lens Video Compression : H.264, MPEG4 and MJPEG 2.9 simultaneously (Tri-encoders) Image Resolution : 720P mode: 280x720, 720x576, 320x80, 60fps 2.0.3M mode: 280x024, 800x600, 720x576, 25/30fps 2. Video Profile : 64 Kbps to 6 Mbps Profile Setting : 2.2 Every video profile has Independent CBR/ VBR/ EVBR/ GOP/ Frame rate setting Region of Interest : 2.3 Max p mode. Editable range 2.4 Area of Interest: Max. 2 AOI. Editable range Image Setting: AE, AWB; 3D ise reduction; Digital WDR; Color, brightness, 2.5 sharpness, contrast, Hue; Mirror/Flip; Privacy Masks; Text, time and date overlay; Overlay image on video Streaming : Simultaneously multi-profile streaming; Streaming over UDP, 2.6 TCP, HTTP, or HTTPS; M-JPEG streaming over HTTP (server push); Controllable frame rate and bandwidth; Constant and variable bit rate (MPEG4/ H.264); Region of Interest (ROI) Audio Encoder : RTSP: G.7 64kbps, G kbps, AAC 2.7 (option, by request) 2.8 Audio Streaming : One-way or two-way 2.9 Microphone : External microphone in 2.20 Audio Output : Adjustable audio gain Network Protocols : IPv4, IPv6, TCP, UDP, HTTP, HTTPS, SMTP, FTP, NTP, DNS, 2.2 DDNS, DHCP, DIPS, ARP, Bonjour, UPnP, RTSP, RTP, RTCP, IGMP, PPPoE, Samba, ICMP,SNMP Security : Password protection, IP address filtering, HTTPS 2.22 encrypted data transmission, user access log 2.23 Users : 8 simultaneous unicast users 2.24 Supported Interface : ONVIF 2.25 Event Detection : Intelligent motion detection, audio detection, camera tampering 2.26 Motion Detection : 0-zone video motion detection with included or excluded options 2.27 Audio Detection : Audio level Camera Tampering : Camera dis-focus / move direction / mask Page 7 of 24

8 Alarm Events : File upload via FTP or ; File upload via Samba to NAS; 2.29 tification via , HTTP, and TCP; External output activation; Audio alerting output 2.30 Video Buffer : Pre- and post- alarm buffering 2.3 Ethernet : RJ45 0/00/000M auto negotiation 2.32 Power : 2VDC or 24V AC and PoE IEEE 802.3af Class Mount : Wall, ceiling, Pole as required 2.34 Operating Temperature : -20 Degree C to 60 Degree C 2.35 Humidity : 0% ~ 90% (non-condensing) 2.36 : CE, FCC and UL Listed Camera Housing & mount: iii. Same make as that of camera and suitable for the model number offered as specified by the manufacturer and should be an integrated unit. iv. Shall be compact and indoor / outdoor type as required Connector: RJ-45 0Base-T/00Base-TX/000Base-T; 2VDC power jack; alarm input and output; RS485 (Option Cable); Audio out; External MIC input; Video out; Factory default reset x or Better WEATHER PROOF TDN IP OUTDOOR SPEED DOME (Yes / ) x optical zoom and 2x digital zoom 4CIF, 25 fps supporting 8 users simultaneous access Weatherproof with IP66 rated enclosure, heater and fan built in High speed of pan up to 300 /sec and tilt up to 20 /sec High performance memory with 28 presets and 3 selflearning auto tracks High speed preset at 360 /sec with high accuracy with +/ Built-in web browser for easy configuration 3.8 Should have a minimum Illumination 0.0Ix:ICR-ON 3.9 Should have an ICR (IR cut filter)day/night Function 3.0 Signal-to-ise Ratio:> =50dB Should have BLC on/off function Should have a focal Length of F=3.6mm~90 mm or better 3.3 Pan Angle:360 Rotation Capability 3.4 Tilt Angle:0 ~ Pan Speed:0. ~300 /Sec 3.6 Tilt Speed:0. ~20 /Sec Page 8 of 24

9 3.7 Preset Speed:360 /Sec 3.8 Should have the white balance options of Manual/Auto/Indoor/Outdoor/ATW 3.9 Should have a 3 programmable PTZ tour patterns of 00 Sec or higher 3.20 Power Input:24VAC 2A 60Hz/50Hz, Surge Protector 3.2 Video encoder should have the capability of H.264 and MJPEG Simultaneously 3.22 Should have 4CIF / CIF / QCIF video Profiles 3.23 Frame Rate: Up to 25fps PAL for all profiles 3.24 Users:8 simultaneous unicast users Alarm Events: 3.25 Go to PTZ preset position, and go to a tour; tification via , File upload via FTP or Video Buffer: Pre- and post- alarm buffering 3.27 Protocols: TCP, UDP, HTTP, NTP, DDNS, RTP, RTSP 3.28 Ethernet Port: 0/00M 3.29 ONVIF Complaint 3.30 Certification: CE,FCC, UL 3.3 IP Rating: IP The Video Management System supports 32 video channels, 5 clients licenses 32 channels Dor 6 channel 720P or 8 channel 080P resolution image at real-time storage; 90 days 4CIF Resolution. (Yes / ) 4. NVR should support 32 IP cameras video input 4.2 NVR should have High performance Dual-core embedded microprocessor 4.3 NVR should support 6 channel real time live 4CIF 4.4 NVR should support real time recording of NVR should Support 4 channels simultaneous playback NVR should support HDD hot swap. It should have at least 8 Hard Disk slots Each Hard Disk slot should support Minimum 3 TB h Hard Disk 4.8 NVR should support ONVIF 4.9 NVR should Support H.264 / MJPEG dual codec decoding 4. NVR should Support Web client Remote control. 4.2 NVR Should Support at least 0 Simultaneous users 4.3 NVR should support at least 5 Client/ Viewer Software. 4.4 Viewer/Client Software should support control and View the Cameras Page 9 of 24

10 4.5 NVR Should support Audio input with video streams NVR Should have at least 8 alarm inputs and 2 Output in addition to the camera alarm inputs NVR Should Support different recording modes like 5. Support Web client Remote control. NVR Should support different search mode like Date/Time, Event (Alarm, Motion detection), 4.9 NVR Should support Digital Zoom in Live and play back NVR Should Support different Protocols Like HTTP, TCP/IP, RTSP, UDP, NTP, DHCP etc. NVR Should have 2 RJ-45 port (0/00M/000M), 2 USB 2.0 ports 4.22 NVR should have HDMI, VGA and BNC Monitor Out puts 4.23 NVR should support NFR Feature 4.24 NVR should provide HDD Faulty Alarm 4.25 Operating Temperature : -0 C ~ 55 C 4.26 Certification: CE, FCC, CCC, MA Port POE+ Switch with 4 SFP ports (Yes / ) 5. Ports Density: 24 0/00 Base-T with additional 2 G SFP/Base-T Combo ports. Should support PoE as per IEEE 802.3af and IEEE 802.3at with PoE budget of 370w or more for connecting VoIP phones Should be equipped with internal redundant power supplies for higher availability 5.2 Performance: Switching Capacity: n-blocking Forwarding Rate: Wire Speed n-blocking Multicast: Wire Speed n-blocking 5.3 Layer2 / Layer 3 Features: Static Routing, RIPv, v2 IEEE 802.ad, IEEE 802.Q, LLDP-MED, IEEE 802.D MAC bridges, IEEE 802.s (MSTP), IEEE 802.w (RSTP), Port based VLAN, MAC based VLAN, IP subnet based VLAN,GVRP, 9K jumbo frame 5.4 Multicast Features: IGMPv, IGMP v2, IGMP snooping Querier 5.5 IPv6 Features: Page 0 of 24

11 IPv6 host, IPv6 ACL,ICMPv6 Dual-stack IPv4/IPv6 management IPv6 applications: Web/SSL, Telnet server/ssh 5.6 Security: SSH remote login, SSLv3, TACACS+ IEEE 802.X authentication protocols (TLS, TTLS, PEAP and MD5) IEEE 802.x multiple supplicant mode IEEE 802.X port-based network access control, Port mirroring, RADIUS, RADIUS accounting, Secure Shell (SSHv2), ACL, Dynamic VLAN assignment DHCP (snooping, client and relay), NAC support 5.7 Management: Switch should able to support management via CLI, Web interface SNMP v,v2,v3 support, RMON (groups,2,3 and 9), traps, slow, Switch should be manageable through both IPv4 & IPv6 Should support management, configuration, and software upgrades for up to 20 switches with a single command in a single management session via single IP address 5.8 Certifications: UL-UL60950-, EN 55024, CE, ROHS 5.9 Environmental Conditions: Operating temperature range of 0-40C 5.0 Interoperability: For ease of integration all active components(switches, SFP's) should be of same OEM 5. Approved s: HP, Juniper, Cisco, Allied Telesis LED TV for Viewing of camera (Yes / ) 6. : Samsung / LG / Sony core Optical Fiber Cable Single mode (SM) The specification of Fiber Cabling system should be meet standards as specified below: Single mode fiber cabling system Type from one OEM ( Cables + Components) (Yes / ) Page of 24

12 Networks Supported Standard Performance Testing Warranty Cable Type Fiber Type Fiber core must be of cores 2/24 /0G. All passive components must be from same OEM ( Copper + Fiber) ITU-T G.652 ( A,B,C and D), IEC , TIA/EIA 492CAAB Must have ETL verified fiber Channel compliance to ANSI/TIA568 -C.0 25-year systems warranty; Warranty to cover Bandwidth of the specified and installed cabling system 6 / 2 / 24-core, Single Mode, Armored, Loose-tube, Gel filled ( Multi Tube Construction ) Single Mode, 9 / 25, 250 micron primary coated buffers. UL Listed fiber - Corning make core to ensure optical performance As per Telecordia GR20, ITU-T G652D Armor Cable Construction Type Outer Jacket 30nm Corrugated Steel Tape Armor BELLCORE GR 20 / IEC Losse tube Corrugated steel tape (0.55mm Min)CSTA provided with FRP Rod as strength members High density polyethylene, anti - termite, anti - rodent suitable for direct burial application. < = 0.35 < = 0.20 db/km Max Tensile Load Maximum Crush resistance Operating Temperature Test Parameters Marking: >= 2670 N 3000N -40 deg Cel to +60 deg Cel Must pass the following :- IEC794- -E, IEC794--E2, IEC794--E3, IEC794--E4, EIA , IEC794- -E7, IEC794--E0, IEC794--E, IEC794--F5 The cable has identification marking at regular intervals of meter which will be of permanent nature. The accuracy of the sequential marking will be within +/- 0.5%. 8.0 FIBER PATCH PANELS WALL / RACK MOUNT (Yes / ) Page 2 of 24

13 8. Fiber optic patch panel 8.2 Height U 9-inch, Rack mounted Fiber optic patch panel 8.3 # of fibers 6 / 2 / # of OSP Cables for termination 8.5 Grounding 8.6 Cable Management rings Minimum 2 2 s. of earthling lugs, preloaded Front and rear cable management rings, preloaded 8.7 Adapter plates 6 Port adapter plates 8.8 Fiber optic patch panel 8.9 Construction 8.0 Splice tray 8. Splice tray Construction 8.2 Cable Spools 8.3 cable spools Construction Rack mounted Fiber optic patch panel Complete Aluminum Alloy housing, fully powder coated Dimension: 40 * 25 * 0 mm. Included in LIU not to be quoted separately. Fully cushioned splice holder containing grooves for fixing splice protective sleeves Flame retardant plastic, high impact resistance. Must be part of LIU. Two halves spool design, Stackable design, sufficient room provided for storage of excess cable 8.4 Fiber Optic adapter plate 6-port, SC-Style, SM & MM 8.5 Attenuation 8.6 Adapters Max of 0.75 db per mated pair Available in Simplex and Duplex types. 8.7 Durability < 0.2 db max (000 Matings) 8.8 Standard Compliant as per EIA/TIA 568-B and ISO/IES Optical Fiber Pigtail 9. All optical fiber patch leads shall comprise of Single mode 9/25µm fiber with SC fiber connectors terminated at one end. The optical fiber patch leads shall comply with the following specifications: 9.2 Optical Fiber Corning Single Mode (Yes / ) 9.3 Connector: Ceramic ferrule 9.4 Insertion Loss - <0.2 db 9.5 Cable: 9/25, SM 9.6 Durability 000 mating cycle Page 3 of 24

14 9.7 Standard : G652D, G 657A & G 657B 9.8 Length : meter 0.0 Optical Fiber Equipment Patch Cords SC-LC/ SC-SC Single Mode- Meters 0. Cable type 0.2 Fiber type 0.3 of cores 0.4 Outside Diameter 0.5 Minimum Cable Retention Strength SC-SC type SM. Available in either.6mm or 3mm simplex or Duplex Zipcord., Band insensitive Fiber Single mode 9/ micron primary coated buffers 2 Cable construction Type PVC outer jacket.6mm x 3.0mm (Simplex) or.6mm x 3.3mm(Duplex).6mm:.24 lbs (50 N) 0.6 Operating Temperature -40 Degree to + 60 Degree (Yes / ).0 Category 6 UTP, 4 Pair The specification of UTP Cabling system should be meet standards as specified below: Unshielded twisted pair cabling system, TIA / EIA Type C.2 Category 6 Cabling system specified up to 600Mhz.2 Networks Supported 0 / 00 Ethernet, 55 Mbps ATM, 000 Mbps IEEE 802.3ab Ethernet, and proposed Cat 6 Gigabit Ethernet.3 TIA / EIA 568-B. Complete Channel should be ETL Verified, UL and 3P certified - All three Certificates are mandatory. RoHS Compliant.4 IEEE 802.3ab Zero-bit Error, ETL verified (Yes / ).5 Warranty.6 Performance characteristics to be provided along with bid 25-year systems warranty; Warranty to cover Bandwidth of the specified and installed cabling system Attenuation, Pair-to-pair and PS NEXT, ELFEXT and PSELFEXT, Return Loss, ACR and PS ACR for 3-connector channel.7 Conductors 23 AWG solid bare copper Page 4 of 24

15 .8 Insulation Polyethylene.9 Separator cross shaped seperator between pairs..0 Jacket Flame Retardant PVC. Approvals UL and 3P Listed ETL verified to TIA / EIA Cat 6.2 Operating temperature -20 Deg. C to +60 Deg. C.3 Frequency tested up to 600 MHz.4 Packing Box of 305 meters.5 Delay Skew 25ns / 00m MAX..6 Attenuation 22.8dB/00m at 250MHz ( or less attenuation values ).7 Impedance 00 Ohms + / - 5 ohms.8 Performance characteristics to be provided along with bid Attenuation, Pair-to-pair and PS NEXT, ELFEXT and PSELFEXT, Return Loss, ACR and PS ACR 2.0 Outdoor Junction box 2. Outdoor Junction box shall be IP 65 & Metal with Power coated only. 2.2 Junction Box Size : 600 H X 600 W X 350 D (Yes / ) Meter Pole (Yes / ) 3. 8 Meter pole shall be MS type only. 3.2 Pole shall be self-support type including Foundation and necessary civil work. 4.0 Power cable:- (Yes / ) 4. of core : 3 core 4.2 Core Diameter :.5 Sq. mm 4.3 Cable type: Armoured power cable Technical specification for Ethernet media converter - For Multi mode Fiber (0/00 Mbps) and Port One RJ 45 0/ 00 BASE TX port ST or SC 00 BASE FX fiber port Ethernet Media Converters with no increasing hop count in network 5.3 Data Transfer rate 0/00 Auto Mbps Full Duplex 5.4 Indicators: Power Indication (Yes / ) Page 5 of 24

16 5.5 FX/RX Link Indication UTP/RX Link Indication Full/Half Duplex Indication Compatibility Standards IEEE Base T, 802.3u 00Base TX 5.6 Operating Temperature: 0 to 70 Degree KVA Online UPS 6. Input Voltage Range Frequency Phase 2KVA UPS When load <70% range = 0VAC to 280VAC When load 70% range = 55VAC to 280VAC 2KVA UPS - 45 to 55 Hz Single Phase Input Power Factor 3KVA UPS Output Voltage Range 220VAC +/- % Frequency Range THD (Liner Load) <3% THD (n-liner Load) <5% Overload Capacity Crest Factor 03:0 Waveform Transfer between AC mode and battery mode Transfer between inverter mode and bypass mode Transient variation Transient recovery Bypass transfer time Synchronized range: +/- Hz, +/- 2Hz, +/-3Hz selectable : Free running: 50Hz +/- 0.2 % Auto resume when load revert to normal Pure sine wave 0mm 2KVA UPS- Transfer time: 4ms (typical 2.5ms) <+/-5V for 00% step load change < 20ms <2.5 ms Efficiency >90% 6.3 Battery Type DC Voltage Change Current (Long Backup) Recharge Time Electrical Protection Alarms 2V SMF Battery (Lead Acid dry cell) 2KVA - 96VDC 20% * Battery AH (at Float Voltage) >90% capacity after 8 hrs charging Input/output/under voltage, over temperature, overload, short circuit, battery low trip Line Failure, battery low, transfer to Page 6 of 24

17 Communication Interface LED Indication ise Level Standards Battery 6.4 Environment bypass and systems fault Rs232 : SNMP (Optional) Load or battery capacity <45dB EN ; IEC ; IEC ; IEC Exide / Amara Raja / HBL / Rocket Temperature 0-45 C Humidity 0% to 95% (n- condensing ) Altitude <500m Storage Temperature 25 to 55 C 6.5 Other Isolation Transformer External for output Instruction for Cabling Work:- Following procedure shall be followed for laying of the underground cables. (a) The trench shall be meter deep from the finished level of the plant and 0.5 meter wide. (b) 0 bricks per meter shall be laid and 75 mm sand layer below and above cable shall be filled. Wherever laying is done along the wall or in Existing trenches, HDPE pipe shall be used which is in the scope of supplier. The pipe shall be clamped on the walls using Aluminum clamps. Aluminum clamps shall also be in the scope of vendor and the cost of the same shall be included in quoted rates. The maximum distance between two clamps shall be decided based on site condition and size of the cable. Page 7 of 24

18 Appendix-E VMS SOFTWARE FEATURES (Comply : Yes /NO) : The VMS application software shall have following major features: A. Architecture:. Single Location: System shall adopt centralized architecture. All configuration data of IP Video Solution shall be stored in Database Management Centre. System shall have capability to access live and recorded data from NVR only. Video (Live and Recorded) need not to be routed through VMS Database Server, so that VMS-Client application shall continue to access Live and Recorded video in case of VMS Database Server failure. B. Open Standard Support: VMS Software shall be ONVIF compliant so that it can integrate with multiple digital IP cameras, multiple digital and network video recording devices, multiple video matrix switchers and matrix keyboards. C. System Integration: System shall have Integration capabilities with electronic access control system, Intrusion detection system, video analytics and data management utility. In an event of an alarm generated by Access Controller or Intrusion Detection System the software shall ensure that the operator is automatically provided with the CCTV video from the designated camera to view the alarm location as soon as the alarm is received, allowing the operator to visually assess the event and also providing continuous recording. The software shall also automatically focus the nearest PTZ cameras to view to the point of alarm. D. Compression Techniques: System shall use various compression techniques simultaneously to utilize storage and network bandwidth effectively. Video compression techniques shall including H.264, MPEG-4 and M-JPEG as minimum. E. Multi Operations: Managing pentaplex user operations of attached recording devices simultaneously, including live viewing, recording, playback, and handling the exchange of data between the server and a remote workstation. F. Alarm Management: System shall receive alarms & events from multiple video, access and alarm devices. It shall provide capability of Alarm & event viewing, management and interlocking. Alarm interlock logic shall reside in VMS Server which will trigger device to execute preset operations on receiving of an alarm. G. Reports: Log Report shall be used to search the device alarm events, device operations, user login, and web operation. It shall also be used to set queries to get results quickly. Log reports shall be exported in XML, CSV, TIFF, PDF, Web Archive and Excel file formats. H. Search: System shall manage investigation, post-recording motion detection, motion detection-based recording, Alarm (from any of integrated solution CCTV, Access Control and Intrusion Detection) Based recording and search tools with advanced search capabilities of the recording devices. I. User Rights: System shall provide multi-level user access rights for viewing and managing access to the recorder functions. The user level shall range from 0 to 255; the bigger the number, the higher the control priority is. J. Recording Modes: System shall support recording modes of continuous, scheduled, manual, event and alarm-based recording. K. Network: System shall support for both multicast and unicast network topologies and communication protocols. Page 8 of 24

19 L. Rule engine: This capability shall allow for custom scripts and to provide both customization and third party integration. Rules Engine Service shall provide functions such as rules analysis, state monitoring and rules management. By way of logical programming for various devices and event alarms in graphical editing interface, Rules Engine Service shall perform automatic execution of rules when emergency occurs. The visual dynamic user interface shall make it easy to acknowledge alarm circumstances and allows prompt response in case on emergency. M. Client Application: VMS shall provide at least 5 Client licenses as inbuilt. System shall provide unified VMS-Client login to users. User shall be able to login from any PC loaded with VMS-Client application. User shall have the option of two modes of user logins N. Hardware: System shall utilize off-the-shelf computer workstations, servers, networking and storage equipment. proprietary hardware shall be acceptable. VMS-CLIENT FEATURES: VMS-Client Application shall have below mentioned features: A. Live View: Main video viewing screen capable of showing, 4, 9, 6 and other customized split layout of live or recorded video. Standard presets may be customized to the user preferences. B. Scenarios: Current view can be saved as scenario and allowing the user to restore this view at any later point in time. These scenarios shall be modified, overwrite or deleted as and when required. C. Drag and Drop: VMS-Client application shall provide drag and drop functionality. Particular video device can be dragged onto main video viewing screen to view live video. D. Favorites: VMS-Client application shall have feature to save favorites, where user can create a device/scenario folder and drag devices/scenarios into it so that these can be quickly accessed. E. Patrol: VMS-Client application shall provide user the capability of configuring and running video patrol sequences to automatically play videos of multiple channels in specified windows by turns. A patrol shall include several scenarios and a scenario includes several video channels. F. PTZ Control: Support IP PTZ through GUI and the keyboard. PTZ control shall be used for adjusting PTZ movement and setting the focus, aperture and preset bit of the camera. G. Snapshot: Capable of capturing snapshot of live video and allowing user to export snapshot. Snapshot tool shall be available in video window itself. Only the authorized users shall have snapshot functionality. H. Video Export: VMS-Client shall have capability of download and export recorded video from recorders. Exported video clip shall be in OEM s native format to ensure data integrity. Download link to the player shall be provided with video exported. I. Playback: VMS-Client shall be able to playback recorded video from recorders. Different playback modes shall be there as 8x, 6x, 32x, 64x, frame by frame and backward playback. J. Instant Playback: Allow the user to view and save 30sec ago instant playback for any playing live video. It shall be used for monitoring emergent situation. This function shall be enabled by default, if required, user may disable this function. K. Recording: Allows the user to initiate recording through GUI. Recording can be initiated remotely on NVR and locally on VMS-Client PC. L. Alarm Management: Capability of complete alarm management for the alarms coming from recorders, switchers, intrusion detection systems and access control systems. Alarm Management shall be based on below mentioned aspects: i. User shall get the pop-up message for response plan upon receiving the alarm so that same response plan can be followed by each operator. Page 9 of 24

20 ii. notification can be sent out which shall include alarm information and User editable information along with individual alarm. One or multi receiver addresses and SMTP can be assigned for notification. M. E-Maps: VMS-Client shall have capability to upload GIS Map which shall support.shp, AutoCAD, bmp, jpg, png format file. These maps can be interlinked with 8 levels. Devices including cameras, access control readers and intrusion detectors shall be planted on maps. E-map application shall have below mentioned functionalities: i. Video verification can be displayed within second after alarm is triggered. ii. iii. Multi video verification (at least four) can be triggered by same alarm input. Alarm can come from any kind of event notification which system can recognize. N. Surrounding Camera View: VMS-Client application shall have facility of surrounding camera view. It shall support setting presets in surrounding cameras. i. In a surround view, video from a specific device shall be playing in the center and the other surround videos will be from surrounding video devices. Once the object moves to some other camera s FOV, operator can pull that camera in the center and surrounding videos from the associated surrounding camera plays in the surround views. Every video device can be configured one surround view with related 2 surrounding cameras. There shall not be any limit in defining such surround views. ii. iii. Surround video can be called through keyboard and VMS-Client operation. Surround video can be configured through web or VMS-Client. O. Alternate Camera View: For continuous monitoring, system shall have alternative view functionality. Every camera can be assigned an alternative view camera. If one camera is unavailable, operator can achieve alternative camera to get same/similar scene. i. Alternative view camera can be called through keyboard and VMS-Client operation. ii. Alternative view camera can be assigned through web configuration or through NVR-Client. P. Operations: Option to perform various operations through context menu on a particular video (live/recorded/patrol). These operations shall include: Full screen, point and drag, enable square select, digital zoom, start recording, stop recording, take snapshot, show surrounding cameras, trigger alternative view. Q. Timeline Control: Ability to manage timeline control of the recording device, which provides camera recording statistics. Timeline control shall have following features: time slider, time search, time jump, play controls. Timeline control shall also include dedicated buttons for step reverse and step forward and keyboard shortcuts for playback operations. R. Keyboard Functionality: VMS-Client shall be controllable by a keyboard controller connected to the VMS server and shall have following major features: Selecting layout, ending monitor commands, switching operations, PTZ control operations. PTZ control latency shall be less than 500ms S. Search: The search facility shall include search based on date and time, device type, trigger type, alarm, operator, location and site. The search facility shall be able to search records in specified recorder. T. Device and Service Status: VMS-Client shall be capable to show the running status of Event & Control services, Rule Engine service and VMS site in bottom status bar. It shall also monitor connected devices status. U. Server Usage: VMS-Client shall provide facility to view CPU, Memory and Network usage information. Page 20 of 24

21 GENERAL REQUIREMENTS: a. Original Equipment Manufacturer of Video Surveillance System shall have base with technical support function & service support in all regions especially India by OEM itself through authorized partners. b. Manufactured products shall have quality system compliance and shall be either UL or CE (EN) or FCC certified. c. The Video Management software, NVR and the Cameras should be from the same OEM for seamless integration. d. All the IP cameras shall be freely accessible and programmable from the control room. e. The power supply available shall be 220 V / 50 Hz AC +/- 0%. All modules of the surveillance system should work using this power supply only with requisite converters & surge protector, if required. f. All the cameras and other modules of Video Surveillance System shall be modular in construction. g. Approved makes: Bosch, Axis, DVTEL, Honeywell, American Dynamics, LG, Verint. h. Bidder should have authorized service center / office in Gujarat. i. OEM should have relevant experience in installing True IP camera s solution for multi locations units/ blocks in an industrial environments restrict to any of the State or Goverment or Large Private power generation or transmission or distribution Sectors in India with a minimum installation of more than 90 camera s across multiple units/blocks with an centralized VMS architecture & local recorder at unit/block levels. Credentials in the form of completion certificate mentioning make of OEM model numbers should be furnished. j. All the camera s, software & NVR offered should be ONVIF complaint. k. VMS for minimum 300 cameras viewing and recording license along with 20 client licenses should be considered at Central location for centralized monitoring & Recording purpose. l. Considered VMS must have both facilities viewing and recording of cameras. additional license need to purchase for Recording of camera. m. VMS (Centralized Software) should have capability of being scalable and can add up to 000 Cameras (For Viewing and recording) if required. Page 2 of 24

22 Appendix-F BILL OF MATERIAL FOR IP CCTV SYSTEM FOR SURAT DIVISIONAL STORE :- Sr.. Description Qty Supply, Installation, Testing and Commissioning of 720P@60fps Vari-focal IR Network Bullet Camera with /3" Sony progressive scan Exmor CMOS image sensor & 3.3 to 2 mm Varifocal Lens with IP 66 Protection Supply, Installation, Testing and Commissioning of 720P@60fps Vari-focal IR Network Fixed Dome Camera with /3" Sony progressive scan Exmor CMOS image sensor & 3.3 to 2 mm Varifocal Lens Supply, Installation, Testing and Commissioning of 36 X Optical Zoom & 2 X Digital Zoom IP PTZ dome, /4 type CMOS, Day/night, H.264/MJPEG, PAL, 24VAC, IP 66 Standard Outdoor Camera with Pole Mounting and accessories. The Video Management System supports 32 video channels, 5 clients licenses 32 channels Dor 6 channel 720P or 8 channel 080P resolution image at real-time storage; 90 days 4CIF Resolution. 32" FULL HD LED / LCD TV for viewing of Camera and it will connected through desktop PC as per Annexure I. Supply, Installation, Testing and Commissioning 24 RJ-45 autosensing 0/00/000 PoE+ ports (IEEE Type 0BASE-T, IEEE 802.3u Type 00BASE-TX, IEEE 802.3ab Type 000BASE-T, IEEE 802.3at PoE+); Duplex: 0BASE- T/00BASE-TX: half or full; 000BASE-T: full only 4 fixed Gigabit Ethernet SFP ports RJ-45 serial console port. SFP Modules and switch should be of the same make. 7 5 Kms Single mode Media converter 2 8 Supply and laying of Category 6 Unshielded Twisted Pair cable Supply and laying of 6-core Uni tube Armoured Fiber Optic Outdoor Cable, 9/25 Single Mode Cable 20 0 Supply and laying of 32 MM HDPE Pipe for Laying of Cable Supply and laying of 3 Core x.5 SQMM Armoured Power Cable Supply, Installation and Testing and commissioning of Loaded 6-Port Rack Mount fiber Light Interface. Supply, Installation, Testing and Commissioning of SC-LC Style Single mode Duplex Patch Cord with Meter Length Supply, Installation, Testing and Commissioning of 9U(600 X 000mm) floor mount rack Supply, Installation, Testing and commissioning of 8 meter Pole for mounting of Fix Camera Page 22 of 24

23 6 7 Supply, Installation, Testing and Commissioning of 2 KVA ONLINE UPS SYSTEM WITH BATTERY BACK UP UPTO HOUR. Supply, Installation, Testing and Commissioning of 25MM PVC Pipe for Laying of UTP cable. 8 Soft soil Digging with Refilling 5 9 Hard soil Digging with Refilling Fusion Splicing along with OTDR Testing for Fiber Optic Cable Supply of VMS software for centralise location with minimum 300 channels and minimum 20 client license. Installation, testing, Commissioning, documentation, Project Management Charges Appendix H BILL OF MATERIAL FOR IP CCTV SYSTEM FOR NAVSARI RSO:- Sr.. Description Qty Supply, Installation, Testing and Commissioning of 720P@60fps Vari-focal IR Network Bullet Camera with /3" Sony progressive scan Exmor CMOS image sensor & 3.3 to 2 mm Vari-focal Lens with IP 66 Protection 2 Supply, Installation, Testing and Commissioning of 36 X Optical Zoom & 2 X Digital Zoom IP PTZ dome, /4 type CMOS, Day/night, H.264/MJPEG, PAL, 24VAC, IP 66 3 Standard Outdoor Camera with Pole Mounting and accessories. 3 The Video Management System supports 32 video channels, 5 clients licenses 32 channels Dor 6 channel 720P or 8 channel 080P resolution image at real-time storage; 90 days 4CIF Resolution. 4 32" FULL HD LED / LCD TV for viewing of Camera and it will connected through desktop PC as per Annexure I. 5 Supply, Installation, Testing and Commissioning 24 RJ-45 autosensing 0/00/000 PoE+ ports (IEEE Type 0BASE-T, IEEE 802.3u Type 00BASE-TX, IEEE 802.3ab Type 000BASE-T, IEEE 802.3at PoE+); Duplex: 0BASE- T/00BASE-TX: half or full; 000BASE-T: full only 4 fixed Gigabit Ethernet SFP ports RJ-45 serial console port. SFP Modules and switch should be of the same make. 6 5 Kms Single mode Media converter 0 7 Supply and laying of Category 6 Unshielded Twisted Pair cable 60 8 Supply and laying of 6-core Uni tube Armoured Fiber Optic Outdoor Cable, 9/25 Single Mode Cable Page 23 of 24

24 Supply and laying of 32 MM HDPE Pipe for Laying of Cable. Supply and laying of 3 Core x.5 SQMM Armoured Power Cable Supply, Installation and Testing and commissioning of Loaded 6-Port Rack Mount fiber Light Interface. Supply, Installation and Testing and commissioning of Loaded 6-Port Rack Mount fiber Light Interface. Supply, Installation and Testing and commissioning of Loaded 24-Port Rack Mount fiber Light Interface. Supply, Installation, Testing and Commissioning of SC-LC Style Single mode Duplex Patch Cord with Meter Length Supply, Installation, Testing and Commissioning of 2U(600 X 000mm) floor mount rack Supply, Installation, Testing and Commissioning of Outdoor Weather proof Junction box for LIU and L2 Managed switch with Power Strip. The size of JB should be such sufficient to mount LIU and Switch in single cabin. Supply, Installation, Testing and commissioning of 8 meter Pole for mounting of Fix Camera Supply, Installation, Testing and Commissioning of 2 KVA ONLINE UPS SYSTEM WITH BATTERY BACK UP UPTO HOUR. Supply, Installation, Testing and Commissioning of 25MM PVC Pipe for Laying of UTP cable. 7 Soft soil Digging with Refilling Hard soil Digging with Refilling Fusion Splicing along with OTDR Testing for Fiber Optic Cable Installation, testing, Commissioning, documentation, Project Management Charges Page 24 of 24