Rosemount 2120 Vibrating Fork Liquid Level Switch

Transcription

1 Product Data Sheet Rosemount 2120 Rosemount 2120 Vibrating Fork Liquid Level Switch Function virtually unaffected by flow, bubbles, turbulence, foam, vibration, solids content, coating, properties of the liquid, and product variations No need for calibration and requires minimum installation procedures Easy terminal access, polarity insensitive and short circuit protection No moving parts or crevices means virtually no maintenance Electronic, self-checking, and condition monitoring - Heartbeat LED gives status and health information Adjustable Switching Delay for turbulent/splashing applications Magnetic test point makes functional test easy Small in size and weight Fast Drip Fork Design gives quicker response time especially with viscous liquids Explosion-proof/Flameproof and Intrinsically Safe options SIL 2 of IEC DIBt/WHG overfill protection Contents Reliable Performance...In Challenging Applications page 2 Rosemount 2120 Vibrating Fork Liquid Level Switch page 4 Specifications page 8 Product Certifications page 10 Dimensional Drawings page 12

2 Rosemount 2120 Product Data Sheet Reliable Performance...In Challenging Applications MEASUREMENT PRINCIPLE The Rosemount 2120 is designed using the principle of a tuning fork. A piezo-electric crystal oscillates the forks at their natural frequency. Changes to this frequency are continuously monitored. The frequency of the vibrating fork sensor changes depending on the medium in which it is immersed. The denser the liquid, the lower the frequency. When used as a low level alarm, the liquid in the tank or pipe drains down past the fork, causing a change of natural frequency that is detected by the electronics and switches the output state. When the 2120 is used as a high level alarm, the liquid rises in the tank or pipe, making contact with the fork which then causes the output state to switch. Threaded Process Connection Flanged Process Connection Adjustable Switching Delay KEY FEATURES AND BENEFITS Virtually unaffected by turbulence, foam, vibration, solids content, coating, or liquid properties The 2120 is designed for operation in temperatures from 40 to 02 F ( 40 to 150 C) DIBt/WHG overfill protection certification Electronic self-checking and condition monitoring. The heartbeat LED gives status and health information on the 2120 Adjustable switching delay prevents false switching in turbulent or splashing applications Fast Drip fork design gives quicker response time, especially with viscous liquids Rapid wet-to-dry time for highly responsive switching Fork shape is optimized for hand polishing to meet hygienic requirements No moving parts or crevices for virtually no maintenance Fast Drip Forks 2

3 Product Data Sheet Rosemount 2120 Fit and Forget Once installed, the 2120 is ready to go. It needs no calibration and requires minimum installation The heartbeat LED gives an instant visual indication that the unit is operational Functional testing of the instrument and system is easy with a magnetic test point You can install, and forget it Superior Performance The 2120 is a popular choice for high and low level alarm and pump control duties for its simplicity, ease of use, and reliability Functionality is virtually unaffected by flow, turbulence, bubbles, foam, or vibration The Fast Drip design allows the liquid to be quickly drawn away from the fork tip, making the 2120 quicker and more responsive in high density or viscous liquid applications With a user-selectable time delay feature, the risk of false switching is minimized in turbulent or splashing applications APPLICATIONS Overfill protection High and low level alarms Pump control or limit detection Run dry or pump protection Hygienic applications High temperature applications Wireless applications High And Low Level Alarm High Temperature Applications Pump Control / Limit Detection Wireless Applications

4 Rosemount 2120 Product Data Sheet Rosemount 2120 Vibrating Fork Liquid Level Switch Rosemount 2120 capabilities include: Ideal for almost all liquid applications Wide choice of materials, process connections, and switching mechanisms configurable for your application Electronic, self-checking, and condition monitoring User-adjustable mode selection and time delay switch SIL2 suitable Additional Information Spares and Accessories: page 7 Specifications: page 8 Certifications: page Level Switches Dimensions: page 12 TABLE Ordering Information The offering represents the most common options. The starred options ( ) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. Model Product Description 2120 Vibrating Fork Liquid Level Switch / F ( C) Materials of Construction: Process Connection/Fork D 16/16L Stainless Steel (1.4401/1.4404) dual certified N (1)(2) 16/16L SST (1.4401/1.4404) with NACE compliance to MR 0175:200 (ISO 15156:200), MR Expanded F () ECTFE/PFA copolymer, coated 16/16L SST (1.4401/1.4404) C (4) Alloy C (UNS N10002), Alloy C-276 (UNS N10276), Solid Process Connection Size / Type 0A /4-in. BSPT (R) Thread 0B /4-in. BSPP (G) Thread 0D /4-in. NPT Thread 1A 1-in. BSPT (R) Thread 1B 1-in. BSPP (G) Thread 1D 1-in. NPT Thread 1P 1-in. BSPP (G), O-ring, Hygienic Fitting 5R 1 1 /2-in. (8 mm) Tri-Clamp, Hygienic Fitting 2R 2-in. (51 mm) Tri-Clamp, Hygienic Fitting 5G 1 1 /2-in. ASME B16.5 Class 150 Raised Face (RF) Flange 5H 1 1 /2-in. ASME B16.5 Class 00 Raised Face (RF) Flange 2G 2-in. ASME B16.5 Class 150 Raised Face (RF) Flange 2H 2-in. ASME B16.5 Class 00 Raised Face (RF) Flange G -in. ASME B16.5 Class 150 Raised Face (RF) Flange H -in. ASME B16.5 Class 00 Raised Face (RF) Flange 4G 4-in. ASME B16.5 Class 150 Raised Face (RF) Flange 4H 4-in. ASME B16.5 Class 00 Raised Face (RF) Flange 5K DN40, EN1092 PN 10/16 Flange 5L DN40, EN1092 PN 25/40 Flange 2K DN50, EN1092 PN 10/16 Flange 2L DN50, EN1092 PN 25/40 Flange 7K DN65, EN1092 PN 10/16 Flange 4

5 Product Data Sheet Rosemount 2120 TABLE Ordering Information The offering represents the most common options. The starred options ( ) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. 7L DN65, EN1092 PN 25/40 Flange K DN80, EN1092 PN 10/16 Flange L DN80, EN1092 PN 25/40 Flange 4K DN100, EN1092 PN 10/16 Flange 4L DN100, EN1092 PN 25/40 Flange Expanded 5J 1 1 /2-in. ASME B16.5 Class 600 Raised Face (RF) Flange 2J 2-in. ASME B16.5 Class 600 Raised Face (RF) Flange J -in. ASME B16.5 Class 600 Raised Face (RF) Flange 4J 4-in. ASME B16.5 Class 600 Raised Face (RF) Flange 5M DN40, EN1092 PN 6 Flange 5N DN40, EN1092 PN 100 Flange 2M DN50, EN1092 PN 6 Flange 2N DN50, EN1092 PN 100 Flange 7M DN65, EN1092 PN 6 Flange 7N DN65, EN1092 PN 100 Flange M DN80, EN1092 PN 6 Flange N DN80, EN1092 PN 100 Flange 4M DN100, EN1092 PN 6 Flange 4N DN100, EN1092 PN 100 Flange XX (5) Customer Specific Electronic Type Available for Certifications S Direct load switching (2-wire) 20 to 264 Vac 50/60Hz, 20 to 60 Vdc NA, E1, E5, E6, E7, G5, G6 B PNP/PLC low voltage (-wire) 20 to 60 Vdc NA, E1, E5, E6, E7, G5, G6 R Relay (SPDT / SPCO) NA, E1, E5, E6, E7, G5, G6 C (6) IS NAMUR (Ex ia) I1, I, I5, I6, I7 Surface Finish Available for Connections 1 surface finish All 2 Hand polished (Ra < 0.4 µm) Hygienic Connection Only Product Certifications Available for Electronic Available for Housing NA No Hazardous Locations Certifications S, B, R A, D G5 (7) FM Ordinary Locations (unclassified, safe area) S, B, R Y, T G6 (8)(9) CSA Ordinary Locations (unclassified, safe area) S, B, R Y, T E1 ATEX Flameproof S, B, R X, S E5 (7) FM Explosion-proof S, B, R Y, T E6 (8) (9) CSA Explosion-proof S, B, R Y, T E7 IECEx Explosion-proof S, B, R X, S I1 ATEX Intrinsic Safety C A, D I NEPSI Intrinsic Safety C A, D I5 FM Intrinsic Safety C A, D I6 (9) CSA Intrinsically Safe C A, D I7 IECEx Intrinsic Safety C A, D Housing Available for Certifications A Glass Filled Nylon, M20 conduits/cable threads NA, I1, I, I5, I6, I7 D Glass Filled Nylon, 1 /2-in. NPT conduits/cable threads NA, I1, I, I5, I6, I7 X Aluminum Alloy, M20 conduits/cable threads E1, E7 Y Aluminum Alloy, /4-in. NPT conduits/cable threads E5, E6, G5, G6 S Stainless Steel, M20 conduits/cable threads E1, E7 T Stainless Steel /4-in. NPT conduits/cable threads E5, E6, G5, G6 5

6 Rosemount 2120 Product Data Sheet TABLE Ordering Information The offering represents the most common options. The starred options ( ) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. Fork Length Available Connection A length 1.7-in. (44 mm) All except flanged models H (2) length flange 4.0-in. (102 mm) All flanged models B (2) Ext 5.9-in. (150 mm) All except Tri-clamp 5R & 2R C (2) Ext 11.8-in. (00 mm) All except Tri-clamp 5R & 2R D (2) Ext 19.7-in. (500 mm) All except Tri-clamp 5R & 2R L (10) Semi-ext.9-in. (98 mm) 1A, 1B, and 1D E (11) Extended, customer specified length in tenths of inches All except 1-in. BSPP O-ring 1P M (11) Extended, customer specified length in millimeters All except 1-in. BSPP O-ring 1P OPTIONS Specific Extended Fork Length XXXX (11) Specific customer specified length in tenths of inches, or millimeters (only if fork length E or M is selected) Calibration Data Certification Q4 Certificate of functional test Material Traceability Certification Q8 (1)(2) Material traceability certification per EN Special Procedures P1 (12) Hydrostatic testing with certificate Overfill U1 (1) WHG/DIBt Overfill Protection Tag Plates ST Tag plate SST engraved plate (maximum 16 digits) WT Tag plate laminated paper (maximum 40 digits) Typical Model Number: 2120 D 0A C 1 I1 A A Q8 ST (1) Only available for wetted parts. (2) Not available for hand polished wet side. () ECTFE/PFA copolymer coating is not available on threaded options. (4) Only available of BSPT and NPT threaded process connection code 0A, 0D, 1A, and 1D as standard, other upon request. (5) Other process connections available upon request. (6) Rosemount 2120 IS Namur Vibrating Fork Level Sensor models 2120***C*I** has demonstrated proven reliability. It is suitable for applications up to SIL 2 of IEC as a Type B Safety Related Subsystem when configured as a high level alarm in conjunction with a Namur Barrier. (7) See Product Certifications on page 10. E5 includes G5 requirements. G5 is for use in unclassified, safe area locations only. (8) See Product Certifications on page page 10. E6 includes G6 requirements. G6 is for use in unclassified, safe area locations only. (9) The requirements of CRN are met when a Rosemount 2120 CSA-approved vibrating fork level switch model is configured with 16/16L stainless steel (1.4401/1.4404) wetted parts and either NPT threaded or 2-in. to 8-in. ASME B16.5 flanged process connections. (10) Only available with stainless steel material of construction D and glass nylon housing A and D. (11) Minimum length available for /4-in. threaded connection is.8 in. (95 mm); for 1-in. threaded, it is.7 in. (94 mm); for flanged, it is.5 in. (89 mm); and for Tri-Clamp, it is 4.1 in. (105 mm). Maximum length is in. (000 mm), except for ECTFE/PFA copolymer coating and hand polished process where the maximum length is 9.4 in. (1000 mm). Examples: Code E1181 is inches. Code M000 is 000 millimeters. (12) Option limited to units with extended lengths up to 59.1-in. (1500 mm). Option is not available for ECTFE/PFA coating. (1) Option not available for Stainless Steel housing codes S and T. 6

7 Product Data Sheet Rosemount 2120 Spare Parts and Accessories TABLE 2. Spare Parts and Accessories The offering represents the most common options. The starred options ( ) should be selected for best delivery. The Expanded offering is subject to additional delivery lead time. Spares and Accessories Seal for 1-in. BSPP (G1A). Material: Non-asbestos BS751 grade X carbon fiber with rubber binder Seal for /4-in. BSPP (G/4A). Material: Non-asbestos BS751 grade X carbon fiber with rubber binder Hygienic adaptor boss 1-in. BSPP. Material: 16 Stainless fitting. FPM/FKM O-ring in. (51 mm) Tri-clamp kit (vessel fitting, clamp ring, and seal). Material: 16 SST, NBR Nitrile Telescopic test magnet (1) 1 1 /2-in. BSPP adjustable clamp gland for 1-in. extended lengths. Material: 16 Stainless steel, (Si) Silicone rubber seal (1) 1 1 /2-in. NPT adjustable clamp gland for 1-in. extended lengths. Material: 16 Stainless steel, (Si) Silicone rubber seal (2) Replacement Cassette: Direct load switching (2 Wire) (Red) (2) Replacement Cassette: PNP/PLC cassette (Yellow) (2)() Replacement Cassette: Intrinsically Safe cassette (Blue) (2) Replacement Cassette: Relay output cassette (Green) (4) Replacement Cassette: FM Direct load switching (2 Wire) (Red) (4) Replacement Cassette: FM PNP/PLC cassette (Yellow) (4) Replacement Cassette: FM Relay output cassette (Green) (1) The adjustable clamp gland is not explosion-proof. (2) Available for Housing codes A and D. () I.S. cassettes can only be replaced with I.S. cassettes. Non-I.S. cassette types can be interchanged with other non-i.s. cassettes, but the new label must be fitted and the original part number transferred to the new label. (4) Available for Housing codes X, Y, S, and T. 7

8 Rosemount 2120 Product Data Sheet Specifications Physical Product Rosemount 2120 Vibrating Fork Liquid Level Switch Measuring principle Vibrating Fork Applications Most liquids including coating liquids, aerated liquids, and slurries Mechanical Housing and Enclosure Housing Code A D X Y S T Housing Material Housing Paint Nylon PA66 0%GF Not Applicable Connections See Process Connection Size / Type on page 4 Extended Lengths The maximum extended length is in. (000 mm) except for a hand-polished 2120 that is limited to 9.4 in. (1000 mm) Process Material 16/16L Stainless Steel (1.4401/ dual certified), Alloy C (UNS N10002) and Alloy C-276 (UNS N10276), or ECTFE/PFA co-polymer coated 16/16L Stainless Steel (1.4401/ dual certified) Hand polished to better than 0.4 m option available for hygienic connections Gasket material for /4-in. and 1-in. BSPP (G) is Non-asbestos BS751 Grade X carbon fiber with rubber binder Dimensional Drawings See Dimensional Drawings on page 12 Al alloy ASTM B26 56-T6 or LM25 TF Polyurethane Powder Coat 16C12 Stainless Steel Not Applicable LED Window PMMA None None Conduit Entry M20 1 /2-in. NPT M20 /4-in. NPT M20 /4-in. NPT Ingress Protection IP66/67 to EN60529 IP66/67 to EN60529, Type 4X IP66/67 to EN60529, Type 4X Performance Hysteresis (water) ±0.09-in. (±1 mm) nominal Switching Point (water) 0.5 in. (1 mm) from tip (vertical) / from edge (horizontal) of fork (this will vary with different liquid densities) Functional Maximum Operating Pressure The final rating depends on the selected process connection. Threaded Connection See Figure 1 for operating pressures. NOTE: Clamp glands and (page 7) limit the maximum pressure to psig (1, bar g) Hygienic Connection 45 psig (0 bar g) Flanged Connection See Figure 1 or Table (whichever one is the lowest) Process Pressure psig (barg) FIGURE 1. Process Pressure 1450 (100) 1160 (80) 2 (0) (-1.0) -40 (-40) 2 (0) 122 (50) 02 (150) Process Temperature F ( C) TABLE. Maximum Flange Pressure Rating Class/Rating SST Flanges ASME B16.5 Class psig (1) ASME B16.5 Class psig (1) ASME B16.5 Class psig (1) EN PN 10/16 10/16 barg (2) EN PN 25/40 25/40 barg (2) EN PN 6 6 barg (2) EN PN barg (2) (1) At 100 F (8 C), the rating decreases with an increasing process temperature. (2) At 122 F (50 C), the rating decreases with an increasing process temperature. 8

9 Product Data Sheet Rosemount 2120 Minimum and Maximum Operating Temperature See Figure 2 for operating temperatures. NOTE: Clamp glands and (page 7) limit the maximum temperature to 257 F (125 C). Ambient Temperature F ( C) Liquid Density Range Minimum 7.5 lb/ft (600 kg/m ) Liquid Viscosity Range 0.2 to cp (centipose) FIGURE 2. Temperature Solids Content and Coating Maximum recommended diameter of solid particles in the liquid is 0.2 in. (5 mm) For coating product, avoid bridging of forks Switching Delay User selectable 0., 1,, 10, 0 seconds delay for dry-to-wet and wet-to-dry switching CIP (Clean In Place) Cleaning Withstands steam cleaning routines up to 02 F (150 C) Electrical 176 (80) 122 (50) 2 (0) -40 (-40) -40 (-40) 2 (0) 140 (60) 02 (150) Process Temperature F ( C) Switching Mode User selectable switching mode (Dry=on or Wet=on) Protection Polarity insensitive. Over-current, short-circuit and load-missing protection. Surge protection to IEC6126. Terminal Connection (wire diameter) Max. 0.1 in 2 (2,5 mm 2 ). Note national regulations. Conduit Plugs/Cable Gland Metal Ex d Housing: Conduit entries for explosion-proof areas are shipped with two brass conduit plugs Plastic housing with direct load, PNP/PLC and IS electronics are shipped with one PA66 (1) cable gland and one blanking plug Plastic housing with relay electronics are shipped with two PA66 (1) cable glands Grounding The 2120 should always be grounded either through the terminals or using the external ground connection provided. Electrical Connections Direct load switching (two-wire) LOAD LINE 1 2 PE (Ground) Neutral 0V R I L Fuse 2A(T) Live +V DPST OPERATION MODE Dry On Mode Dry On Wet On Dry Wet Dry Wet Wet On Mode Seconds Delay Direct Load Switching WARNING Isolate Supply Before Removing Solid state PNP output for direct interface to PLC s (three wire) PE (Ground) + OUT Fuse 2A(T) 4 +V O/P 0V SPCO single relay for voltage free contacts 1 2 PE (Ground) N N 0V 10 0 Intrinsically Safe (IS) NAMUR to DIN 1924, IEC L Fuse 0.5A (T) Live +V DPST 10 0 R = External load (must be fitted ) U = V ~ (ac) (50/60Hz) IOFF < ma IL = mA î = 5A, 40ms U = 20-60V (dc) IOFF < ma IL = ma î = 5A, 40ms OPERATION MODE Dry On Mode Dry On Wet On Dry Wet Dry Wet Wet On Mode Seconds Delay U = 20-60V (dc) I < 4mA + I L IL (MAX) = 0-500mA î = 5A, 40ms UOUT(ON) = U - 2.5V IL (OFF) < 100µA OPERATION MODE Dry On Mode Dry On Wet On Dry Wet Wet Dry Wet On Mode 10 0 U = V ~ (ac) (50/60Hz) I < 6mA U = 20-60V I < 6mA (dc) 10 0 Seconds Delay OPERATION MODE Dry On Mode Dry On Wet On Dry Wet Dry Wet 0 0 Wet On Mode Seconds Delay I ON = I OFF = PLC/PNP Isolate Supply Before Removing RELAY NC C NO NC C NO U MAX = 250V ~ (ac) I MAX = 5A P MAX' = 1250VA, resistive P MAX' = 1000VA, inductive U MAX = 60V (dc) I MAX = 5A, U < 0V I MAX = 1.5A, U < 60V Intrinsically Safe + - Isolating amplifier to NAMUR (IEC , EN50227) must be used to meet I.S. requirements (1) Cable diameter 0.2 to 0. in. (5 to 8 mm) 9

10 Rosemount 2120 Product Data Sheet Product Certifications ORDINARY LOCATION CERTIFICATION FOR FM G5 Project ID: The switch has been examined and tested to determine that the design meets basic electrical, mechanical, and fire protection requirements by FM, a nationally recognized testing laboratory (NRTL) as accredited by the Federal Occupational Safety and Health Administration (OSHA). ORDINARY LOCATION CERTIFICATION FOR CSA G6 Certificate Number: 06 CSA The switch has been examined and tested to determine that the design meets basic electrical, mechanical, and fire protection requirements by CSA, a nationally recognized testing laboratory as accredited by the s Council of Canada (SCC). EUROPEAN DIRECTIVE INFORMATION The EC declaration of conformity for all applicable European directives for this product can be found on the Rosemount website at A hard copy may be obtained by contacting your local sales office. ATEX Directive (94/9/EC) Complies with the ATEX Directive. Pressure Equipment Directive (PED) (97/2/EC) The Rosemount 2120 is outside the scope of PED Directive. L.V. Directive EN Pollution degree 2, Category II (264V max), Pollution degree 2, Category III (150V max) Electro Magnetic Compatibility (EMC) Directive EN6126 Emissions to Class B. Immunity to industrial location requirements. Vibration Resistance EN60721 level M6/4M6 CE-mark Complies with applicable directives (EMC, ATEX, and LVD) Overfill Protection If required, select Product Certificates code U1 for WHG/DIBt overfill protection. The approval number is Z SIL Declaration of Conformity The Rosemount 2120 IS Namur Vibrating Fork Level Sensor (2120***C*I**) has demonstrated proven reliability. It is manufactured and supported in a manner suitable for applications up to SIL 2 of IEC as a Type B Safety Related Subsystem when configured (1) as a high level alarm in conjunction with a Namur Barrier. HAZARDOUS LOCATIONS CERTIFICATIONS North American Approvals Factory Mutual (FM) Explosion-proof Approval E5 Project ID: Explosion-proof for Class I, Div. 1, Groups A, B, C, and D Temperature Class: T6 (T amb 40 to 75 C) Enclosure: Type 4X Factory Mutual (FM) Intrinsically Safe Approval I5 Project ID: Intrinsically Safe for Class I, Div. 1, Groups A, B, C, and D Class I, Zone 0, AEx ia IIC Temperature Code: T5 (T amb 40 to 80 C, Tproc < 80 C) Control Drawing: 71097/1154 Ui=15 V, Ii=2 ma, Pi=0.1 W, Ci=211 nf, Li=0.06 mh NOTE A NAMUR isolating amplifier must be used for intrinsic safety. Canadian Approvals Canadian s Association (CSA) Explosion-proof Approvals E6 Project ID: Explosion-proof for Class I, Div. 1, Groups A, B, C, and D Temperature Class: T6 (T amb 40 to 75 C) Enclosure: Type 4X Canadian s Association (CSA) Intrinsically Safe Approval I6 Certificate Number: 06 CSA Intrinsically Safe for Class I, Div. 1, Groups A, B, C, and D Class 1, Zone 0, Ex ia IIC Temperature Code: T5 (T amb 40 to 80 C, Tproc < 80 C) Control Drawing: 71097/1179 Ui=15 V, Ii=2 ma, Pi=0.1 W, Ci=211 nf, Li=0.06 mh (1) Refer to manual for IEC configuration details. 10

11 Product Data Sheet Rosemount 2120 Canadian s Association (CSA) Non-Incendive Approval I6 Certificate Number: 06 CSA Non-Incendive for Class I, Div. 2, Groups A, B, C, and D Temperature Code: T5 (T amb 40 to 80 C, Tproc < 80 C) Control Drawing: 71097/1187 Ui=15 V, Ii=2 ma, Pi=0.1 W, Ci=211 nf, Li=0.06 mh NOTE A NAMUR isolating amplifier must be used for intrinsic safety. Canadian Registration Number (CRN) CRN 0F C NOTE The requirements of CRN are met when a Rosemount 2120 CSA-approved vibrating fork level switch model is configured with 16/16L stainless steel (1.4401/1.4404) wetted parts and either NPT threaded or 2-in. to 8-in. ASME B16.5 flanged process connections. European Approvals ATEX Flameproof Approval E1 Certificate: Sira 05ATEX1129X Flameproof and Dust: ATEX Marking II 1/2 G D Ex d IIC T6 to T2 Ex td A21 (T85 C to 265 C) IP6X ATEX Intrinsically Safe Approval I1 Certificate: Sira 05ATEX210X Intrinsic Safety and Dust: ATEX Marking II 1 G D Ex ia IIC T5 to T2 Ex iad 20 (T85 C to 265 C) IP6X Ui=15 V, Ii=2 ma, Pi=0.1 W, Ci=12 nf, Li=0.06 mh International Approvals National Supervision and Inspection Centre for Explosion Protection and Safety Instrumentation (NEPSI) Intrinsically Safe Approval I Certificates: GYJ0650 (when manufactured in Slough, UK) GYJ0651 (when manufactured in Singapore, Singapore) Intrinsic Safety: Ex ia IIC T5 (T amb 40 to 60 C) Ui=15 V, Ii=2 ma, Pi=0.1 W, Ci=12 nf, Li=0.06 mh NOTE A NAMUR isolating amplifier must be used for intrinsic safety. International Electrotechnical Commission (IEC) Flameproof Approval E7 Certificate: IECEx SIR X Flameproof and Dust: Zone 0/1 Ex d IIC T6 to T2 Ex td A21 (T85 C to 265 C) IP6X International Electrotechnical Commission (IEC) Intrinsically Safe Approval I7 Certificate: IECEx SIR X Intrinsically Safe and Dust: Ex ia IIC T5 to T2 Ex iad 20 (T85 C to 265 C) IP6X Ui=15 V, Ii=2 ma, Pi=0.1 W, Ci=12 nf, Li=0.06 mh NOTE A NAMUR isolating amplifier must be used for intrinsic safety. NOTE A NAMUR isolating amplifier must be used for intrinsic safety. 11

12 Rosemount 2120 Product Data Sheet Dimensional Drawings Threaded Mounting Glass Filled Nylon B C Glass Filled Nylon B C Cable entry M20x1.5 or /4-in. NPT Aluminum/SST B C 5.60 (142) E (M) (If Horizontal) Cable Gland (40) A/F Hexagon /4-in. or 1-in. Thread 0.9 (2) for /4-in. Thread 1.14 (29) for 1-in. Thread D (If Vertical) /4-in. or 1-in. Thread 2.72 (69) 1.7 (44) (If Horizontal) Cable Entry M20x1.5 or 1 /2-in. NPT (40) A/F Hexagon 0.9 (2) for /4-in. Thread 1.14 (29) for 1-in. Thread (If Vertical) D 2.72 (69) /4-in or 1-in. Thread 1.7 (44) (If Horizontal) (If Vertical) 0.9 (2) for /4-in. Thread 1.14 (29) for 1-in. Thread Note: Dimensions are in inches (millimeters) Thread Length Model Code A Minimum Length Model Code E (M) Maximum Length Model Code E (M) /4 in. 1.7 (44).74 (95) (000) 1 in. 1.7 (44).70 (94) (000) Material B C D Glass Nylon.52 (90) 4.02 (102) 4.72 (120) Aluminum 2.68 (68) 4.02 (102) 6.14 (156) Stainless Steel 2.76 (70) 4.1 (105) 6.0 (160) 12

13 Product Data Sheet Rosemount 2120 Flange Mounting (Glass filled nylon housing shown) B C D Cable Gland E (M) (If Horizontal) 1.14 (29) (If Vertical) Note: Dimensions are in inches (millimeters) Material Length Model Code H Minimum Length Model Code E (M) Maximum Length Model Code E (M) Stainless Steel 4 (102).50 (89) (000) ECTFE/PFA co-polymer coated 4 (102).50 (89) 9.7 (1000) Material B C D (1) Glass Nylon.52 (90) 4.02 (102) 6.0 (160) Aluminum 2.68 (68) 4.02 (102) 6.14 (156) Stainless Steel 2.76 (70) 4.1 (105) 7.87 (200) (1) Varies with flange rating and thickness. D is the nominal maximum thickness and allows a flange up to 1.77 in. (45 mm) thick. This equates to a 4-in. ASME B16.5 Class 600 Raised Face flange. 1

14 Rosemount 2120 Product Data Sheet Hygienic Fitting (Glass filled nylon housing shown) B C B B C C D E (M) Cable Gland 1 1 /2-in. or 2-in. Tri-Clamp D 2.52 (64) 1.7 (44) Cable Gland 1 1 /2-in. or 2-in. Tri-Clamp 0.9 (2) (If Vertical) 1-in. BSPP O-ring Seal D.07 (78) (If Horizontal) 0.9 (2) Cable Gland (40) A/F Hexagon (If Vertical) (If Horizontal) 1.14 (29) (If Vertical) Note: Dimensions are in inches (millimeters) Connection Length Model Code A Minimum Length Model Code E (M) Maximum Length Model Code E (M) Tri-Clamp 1.7 (44) 4.1 (105) (000) O-ring Seal (1-in. BSPP) 1.7 (44) Not Applicable Not Applicable Material B C D Glass Nylon.52 (90) 4.02 (102) 4.96 (126) Aluminum 2.68 (68) 4.02 (102) 6.14 (156) Stainless Steel 2.76 (70) 4.1 (105) 6.54 (166) 14

15 Product Data Sheet Rosemount

16 Rosemount 2120 Product Data Sheet Rosemount Level Solutions Emerson provides a complete range of Rosemount products for level measurement applications. Vibrating Fork Switches Point Level Detection For high and low alarms, overfill protection, pump control, including wide pressure and temperature requirements, and hygienic applications. Flexible mounting. Immune to changing process conditions and suitable for most liquids. The product line consists of: Rosemount 2160 Wireless Rosemount 210 Enhanced Rosemount 2120 Full-featured Rosemount 2110 Compact Differential Pressure Level or Interface Measurement Flexible mounting for liquid tank levels, including those with wide temperature and pressure requirements. Can be isolated by valves. Unaffected by: vapor space changes, surface conditions, foam, corrosive fluids, internal tank equipment. Optimize performance with direct mount, Tuned-System Assemblies: Rosemount DP Level Transmitters and Remote Seals Rosemount 051S_L, 051L, and 2051L Liquid Level Transmitters Ultrasonic Level Measurement Top mounted, non-contacting for simple tank and open air level measurements. Unaffected by fluid properties such as: density, viscosity, dirty coating, and corrosiveness. Appropriate for routine applications outside of explosion proof areas. The product line consists of: Rosemount 100 Series Ultrasonic Process Level Transmitters Guided Wave Radar Level and Interface Measurement Top mounted, direct level and interface measurement of liquids or solids, including those with wide temperature and pressure requirements. Unaffected by changing process conditions. Good fit for small spaces and easy swap for older technologies. The product line consists of: Rosemount 500 Series Accurate, superior performance transmitter in most applications including process vessels and control Rosemount 00 Series Versatile and easy-to-use transmitter in most liquid storage and monitoring applications Non-contacting Radar Level Measurement Top mounted, direct level measurement for liquids or solids, including those with wide temperature and pressure requirements. Can be isolated by valves. Unaffected by changing process conditions. Good for dirty, coating, and corrosive applications. The product line consists of: Rosemount 5400 Series Accurate, superior performance 2-wire transmitters for most liquid level applications and process conditions Rosemount 5600 Series 4-wire transmitters with maximum sensitivity and performance for solids, challenging reactors, rapid level changes, and excessive process conditions Chambers for Process Level Instrumentation Rosemount 9901 High quality chambers for external mounting of level measurement and control instrumentation on process vessels The Emerson logo is a trademark and service mark of Emerson Electric Co. Rosemount and the Rosemount logotype are registered trademarks of Rosemount Inc. All other marks are the property of their respective owners. Terms and Conditions of Sale can be found at Rosemount, Inc. All rights reserved. Emerson Process Management Rosemount Measurement 8200 Market Boulevard Chanhassen, MN 5517 USA Tel (USA) Tel (International) Fax Emerson Process Management Blegistrasse 2 P.O. Box 1046 CH 641 Baar Switzerland Tel +41 (0) Fax +41 (0) Emerson FZE P.O. Box 170 Jebel Ali Free Zone Dubai UAE Tel Fax Emerson Process Management Asia Pacific Pte Ltd 1 Pandan Crescent Singapore Tel Fax Service Support Hotline: Enquiries@AP.EmersonProcess.com Rev FA 11/10