DOCUMENT DESPATCH ADVICE TECHNICAL COMMITTEE: LITD 07 Ref: Date

Transcription

1 WIDE CIRULATION DOCUMENT DESPATCH ADVICE TECHNICAL COMMITTEE: LITD 07 Ref: Date ADDRESSED TO: LITD 07/T-2, 162 & Dear Sir(s), 1. All Members of Audio, video and multimedia Sectional Committee, LITD All Principal Members of Electronics and Information Technology Division Council (LTDC) 3 All Members of all the Panels of LITD 07 Sectional Committee 4 All others interested Please find enclosed the following Draft Indian Standards in Wide Circulation: 1 DOC:LITD 07(3474) : Audio, video and similar electronic apparatus Safety requirements (Fifth Revision of IS 616) (IEC60065:2014) 2 DOC:LITD 07(3475) : DC power supply for notebook computers (IEC TS 62700:2014) 3 DOC:LITD 07(3476) : Battery charging interface for mall handheld multimedia devices Part 1: 2mm barrel interface [IEC 62637(Part 1):2011] Kindly examine these draft standards and forward your views stating any difficulties which you are likely to experience in your business or profession, if this is finally adopted as a National Standards. Last Date for comments : Comments, if any, may please made in the format indicated and mailed to the undersigned at the address given below. In case no comments are received or comments received are of editorial nature, you may kindly permit us to presume your approval for the above document as finalized. However, in case of comments of technical in nature are received then it may be finalized either in consultation with the Chairman, Sectional Committee or referred to the Sectional committee for further necessary action if so desired by the Chairman, Sectional Committee. This document is identical with corresponding IEC Standard and is not attached with this letter. For considering comments on the document corresponding IEC Standard may be referred. In case of soft copy of IEC standard is required, a request may be sent by mail. Thanking you, Yours faithfully, (D. Goswami)

2 Sc. `F &Head (Electronics & IT) Encl: As above Tele Fax: य पक पर च लन मस द रल ख र षण स ञ पन तकन क सममतत : एलआईट ड 07 स द भ ददन क एलआईट ड 07/ट -2,162, प न व ल क न म: 1) ऑडडय व डडय़ और म ट ममडडय त र एव उप कर ववषय सममतत, एल आई ट ड 07 2) इल र त क एव स च र य ग क ववभ पररषद क रध सद य 3) एलआईट ड क सभ प ल क सद य 4) अ य गच रख व ल मह दय(य ) त मलखखत रल ख य पक पररच ल क मलए स ल ह : 1 एलआईट ड 07(3474) : र य, व डडय एव सम न एल र तनक उपक ण स ष अप ष ऍ 2 एलआईट ड 07(3475) : न टब क क पय ट क मलए ड स ड स बबजल क आप ततभ 3 एलआईट ड 07(3476) : छ ट स म ट ममडडय उपक ण क मलए ब ट च जभ इ ट फ स ग 1: 2 ममम ब ल इ ट फ स क पय इस मस द क अवल क कर और अप स मततय, यह बत त ह ए कक यदद यह भ रत य म क रक म त ह त अमल कर म आप क यवस य म य कद ईय आ सकत ह, भ ज स मततय भ ज क अ ततम ततग यदद क ई स मतत र त ह ह त य स मतत स प दक य रक तत क ह त ह त क पय य अ तम ह त उपर त मस द क मलए आपक अ म द म ल क अ मत द त वप, यदद आपक स मतत क रक तत तक क ह त यदद च यरम ववषय सममतत व र ऐस रह व त त ह त इस आ क आव यक क रव ई क मलए च यरम ववषय सममतत क प स पर म र ह त य ववषय सममतत क प स अवल क र करक अ तम ककय ज ए यह मस द आईईस म क क अ स र सब ध ह त इस पर क स स ल ह ह आईईस म क क ब द मस द पर ववच र र अवल क ककय ज ए यदद आईस म क क स ट रतत अप ष त ह त म ल व र अ र ध भ ज ज ए

3 यदद क ई स मततय क ऊपर त ममरत ह त क पय अध ह त र क त मलखखत पत पर स ल फ म ट म भ ज द ध यव द, भवद य, स ल क : उपर त (ड. व म ) व.एफ एव रम ख (इल र त क व आई ट ) ई म ल: : hlitd@bis.org.in litd@bis.org.in

4 Doc No. LITD 07(3274 ) IEC : 2014 भ रत य म नक र य,व ड य एव सम न इल क ननक उपकरण- स रष अप ष ए Indian Standard AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (Fifth Revision) ICS BIS 2014 BUREAU OF INDIAN STANDARDS MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG NEW DELHI Price Group

5 Audio. Video and Multimedia Systems and Equlpments Sectional Committee. LITO 07 NATIONAL FOREWORD This Indian Standard (Fifth Revision) which is identical with IEC : 2014 'Audio, video and similar electronic apparatus - Safety requirements' issued by the International electrotechnical Commission (IEC) was adopted by the Bureau of Indian Standards on the recommendation of the Audio, Video and Multimedia Systems and Equipments Sectional Committee and approval of the Electronics and Information Technology Division Council. This standard was first published in 1957 and subsequently revised in 1981, 1986, 2003 and The fifth revision of this standard is being done to bring it in line with the latest edition of IEC : The text of ISO/IEC Standard has been approved as suitable for publication as an Indian Standard without deviations. Certain conventions are, however, not identical to those used in Indian Standards. Attention is particularly drawn to the following: a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as decimal marker. In this adopted standard, reference appears to certain International Standards for which Indian Standard also exist. The corresponding Indian Standard which is to be substituted in its respective place is listed below along with its degree of equivalence for the edition indicated: International Standard Corresponding Indian Standard Degree of Equivalence IEC (all parts) Letter symbols to be used in electrical technology IEC :2007 Environmental testing Part 2-6 : Tests Test Fc: Vibration (sinusoidal) IEC :2008 Environmental testing Part 2: Tests Test Ec : Rough handling shocks, primarily for equipment-type specimens IEC Environmental testing Part 2-75: Tests Test Eh: IS 3722 (Parts 1 and 2) : 1983 Letter symbols and signs used in electrical technology IS 9001 : Part 13 : 1981 Guidance for environmental testing - Part 13 : Vibration (sinusoidal) test IS 9002 : (Part 10/ Sec 1):1985 Equipment for environmental tests for electronic and electrical items : Part 10 Shock test machine, Section 1 : Free fall type IS 9000 : (Part 7/ Sec 7):2006 Basic environmental testing procedures for electronic and Technically Equivalent Technically Equivalent Technically Equivalent

6 Hammer tests IEC Environmental testing Part 2: Tests Test Cab: Damp heat, steady state IEC Electrical insulation Thermal evaluation and designation IEC Method for the determination of the proof and the comparative tracking indices of solid insulating materials Amendment IEC (all parts) Miniature fuses IEC 60167:1964 Methods of test for the determination of the insulation resistance of solid insulating materials electrical items: Part 7 Impact test section 7 Test Eh : Hammer tests IS 9000 (Part 4): 2008 Basic environmental testing procedures for electronic and electrical items: Part 4 Damp heat (steady state) IS 1271 : 2012 Electrical Insulation-thermal Evaluation and Designation IS 2824 : 2007 Method for determining of the proof and the comparative tracking indices of solid insulating materials. IS/IEC 127 (All Parts) Miniature fuses IS 2259 : 1963 Methods of test for determination of insulation resistance of solid insulating materials Technically Equivalent with IC document 15(Central Office) IEC (all parts) Electrical insulating materials Thermal endurance properties IEC 60227(allparts)Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V IEC (all parts) Rubber insulated cables Rated voltages up to and including 450/750 V IS 8504 (All parts) Guide for determination of thermal endurance properties of electrical insulating materials IS 694 : 2010 Polyvinyl Chloride Insulated Unsheathed And Sheathed Cables/cords With Rigid And Flexible Conductor For Rated Voltages Up To And Including 450/750 V IS 9968 (Part 1):1988 Elastomer insulated cables:part 1 For working voltages upto and including 1100 V (first revision) IS 9968 (Part 2):2002 Elastomerinsulated Cables - Part 2 : For Working Voltages from 3.3 kv up to and Including 3 3kV IEC (all parts) IS 5921 (All Parts) Specification

7 Base materials for printed circuits Part 2: Specifications IEC :1985 Sound system equipment Part 1: General IEC Specifications for particular types of winding wires Part 43: Aromatic polyimide type wrapped round copper wire, class 240 IEC Household and similar electrical appliances Safety Part 1: General requirements IEC :2008 Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC :2005, Fixed capacitors for use in electronic equipment Part 14: Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains IEC Graphical symbols for use on equipment IEC (all parts) Pressure-sensitive adhesive tapes for electrical purposes IEC 60529:1989 Degrees of protection provided by enclosures (IP Code) for metal-clad base materials for printed circuits for use in electronic and telecommunication equipment IS ( Part 1 ) 2005 Sound system equipment - Part 1 General IS (All Parts) Specification for particular types of winding wires IS 302 (Part 1) : 2008 Safety of household and similar electrical appliances : Part 1 General Requirements. IS 7305 : 1984 Fixed Capacitors Used in Electronic Equipment IS QC : 1994 Fixed capacitors for use in electronic equipment sectional specification for fixed capacitors for electromagnetic interference suppression and connection to the supply mains IS 2032 (All Parts) Graphical symbols used in electrotechnology IS 7809 (All Parts) Specification for pressure sensitive adhesive insulating tapes for electrical purposes IS : 1987 Classification of degrees of protection provided by enclosures of electrical equipment IEC :2007 Insulation IS : Part 1 : 2003

8 coordination for equipment within low-voltage systems Part 1: Principles, requirements and tests IEC Insulation coordination for equipment within low-voltage systems Part 3: Use of coating, potting or moulding for protection against pollution IEC 60691:2002 Thermal links Requirements and application guide IEC :2009, Winding wires Test methods Part 3: Mechanical properties IEC :2008 Winding wires Test methods Part 5: Electrical properties IEC :2012 Winding wires Test methods Part 6: Thermal properties Insulation coordination for equipment within low-voltage systems : Part 1 Principles, requirements and tests IS : Part 3 : 2006 Insulation coordination for equipment within low-voltage systems Part 3 Use of coating, potting or moulding for protection against pollution IS/IEC Pub 691 : 1993 Thermal links - Requirements and application guide (first revision) IS : Part 3 : 2012 Winding wires - Test methods Part 3 Mechnical Properties. IS (Part 5) : 2012 Winding Wires Test Methods Part 5 Electrical Properties IS (Part 6): 2011 Winding Wires - Test Methods : Part 6 Thermal properties. IEC :2005, Information technology equipment Safety Part 1: General requirements Amendment 1:2009 Amendment 2:2013 IEC :1991, Varistors for use in electronic equipment Part 2: Sectional specification for surge suppression varistors Amendment 1:2009 IEC Electroacoustics Octave-band and fractionaloctave-band filters ISO 261 ISO general purpose metric screw threads General plan IS : Part 1:2010 Information Technology Equipment -- Safety Part 1 General Requirements IS QC : 1994 Varistors for Use in Electronic Equipment - Sectional Surge Suppression Varistors IS 6964 : 2001 Electroacoustics - Octave-band and fractionaloctave-band filters (first revision) IS 4218 (Part 2) : 2001 ISO General Purpose Metric Screw Threads - Part 2 : General Plan ISO 262 ISO general- IS 4218 (Part 4):2001 ISO

9 purpose metric screw threads Selected sizes for screws, bolts and nuts ISO 306:2004, Plastics Thermoplastic materials Determination of Vicat softening temperature (VST) IEC :2000 Primary batteries Part 4: Safety of lithium batteries General Purpose Metric Screw Threads - Part 4 : Selected Sizes for Screws, Bolts and Nuts. IS (Part 6/Sec 1):1999 Plastics - Methods of testing:part 6 Thermal properties, Section 1 Determination of vicat softening temperature of thermoplastic materials IS 6303(Part 4):2013 Primary Batteries: Part 4 Safety of Lithium Batteries IEC :1997, Methods of measurement on receivers for television broadcast transmissions Part 1: General considerations Measurements at radio and video frequencies IEC , Miniature fuses. Part 6: Fuse-holders for miniature cartridge fuselinks. IEC (all parts) Appliance couplers for household and similar general purposes IEC :2004, Fire hazard testing Part 11-5: Test flames Needle-flame test method Apparatus, confirmatory test arrangement and guidance. IEC 60410:1973, Sampling plans and procedures for inspection by attributes IS 4545(Part 1):2008 Methods of measurement on receivers for television broadcast transmissions: Part 1 General considerations. IS/IEC 127-6:1994 Miniature Fuses - Part 6 : Fuse Holders for Miniature Cartridge Fuse Links. IS/IEC :2001 Appliance couplers for household and similar general purposes (Part 1 Part 1 General requirements & Part 2 / Sec 2 - Interconnection Couplers for Household and Similar Equipment Part 2 / Sec 3 Appliance couplers with a degree of protection higher than ipxo. IS 11000(Part 2/Sec 2):2008 Fire hazard testing: Part 2 Test methods, Sec 2 Needle- Flame Test-Method - Apparatus, Confirmatory Test Arrangement and Guidance (First Revision) IS 10673:1983 Sampling Plans and Procedures for Inspection by Attributes for Electronic Items Technically equivalent IEC :2010, IS/IEC :1999 Automatic Technically equivalent

10 Automatic electrical controls for household and similar use Part 1: General requirements IEC Methods of measurement of touch current and protective conductor current IEC 61032:1997 Protection of persons and equipment by enclosures Probes for verification IEC :2000,Switches for appliances - Part 1: General requirements IEC :2005 Safety of power transformers, power supplies, reactors and similar products Part 1: General requirements and tests IEC 61965Mechanical safety of cathode ray tubes IEC 62133, Secondary cells and batteries containing alkaline or other non-acid electrolytes Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications IEC 62471:2006 Photobiological safety of lamps and lamp systems ISO :1999, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality level (AQL) for lot-by-lot inspection ISO 9773, Plastics Determination of burning electrical controls for household and similar use : part 1 General Requirements IS 60990:1999 Methods of measurement of touch current and protective conductor current IS 1401:2008 Protection Of Persons And Equipment By Enclosures - Probes For Verification IS/IEC :2000 Switches for appliances : Part 1 General requirements IS/IEC :1997 Safety of power transformers, power supply units and similar : Part 1 General requirements and tests IS/IEC 61965:2003 Mechanical Safety Of Cathode Ray Tubes IS 16046:2012 Secondary Cells and Batteries containing Alkaline or other non-acid Electrolytes - Safety Requirements for Portable Sealed Secondary Cells, and for Batteries made from them, for use in Portable Applications IS 16108:2012 Photobiological Safety of Lamps and Lamp Systems IS 2500(Part 6):2014 Sampling Procedures for Inspection by Attributes Part 6 System of Sequential Sampling Plans Indexed by Acceptance Quality Limit (AQL) for Lot-by-Lot Inspection IS 13360(Part 6/Sec 23):2006 Plastics - Methods of Testing Technically equivalent Technically equivalent Technically equivalent Technically equivalent

11 behaviour of thin flexible vertical specimens in contact with a small-flame ignition source :part 6 Thermal Properties, Section 23 Determination of Burning Behaviour of Thin Flexible Vertical Specimens in Contact With Small-flame Ignition Source The technical committee has reviewed the provisions of following International Standards referred in The technical committee responsible for the preparation of this standard has reviewed the provisions of the following International standards and has decided that they are acceptable for use in conjunction with this standard: International Standard Title IEC 60038:2009 IEC :1997 IEC :2013 IEC standard voltages Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V Part 2: Test methods Fire hazard testing Part 11-10: Test flames 50 W horizontal and vertical flame test methods IEC :2007 Semiconductor devices Discrete devices Part 5-5: Optoelectronic devices Photocouplers along with Amendment 1:2013 IEC :2007 IEC (all parts) IEC IEC IEC Safety of laser products Part 1: Equipment classification and requirements IEC system of plugs and socket-outlets for household and similar purposes Connecting devices for low-voltage circuits for household and similar purposes Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units Connecting devices Electrical copper conductors Safety requirements for screw-type and screwlesstype clamping units Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm 2 up to 35 mm 2 (included) Connecting devices Electrical copper conductors. Safety requirements for screw-type and screwless-type clamping units Part 2: Particular requirements for clamping units

12 for conductors above 35 mm2 up to 300 mm2 (included) IEC/TS IEC IEC , IEC 62151:2000 IEC IEC Guide 104 IEC Guide 112 ISO 7000 ITU-T Recommendation K.44 Guide for safe handling and operation of mobile radio equipment Marking of electrical equipment with ratings related to electrical supply Safety requirements Safety of power transformers, power supply units and similar products for voltages up to V Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units Safety of equipment electrically connected to a telecommunication network Audio/video, information and communication technology equipment Part 1: Safety requirements The preparation of safety publications and the use of basic safety publications and group safety publications Guide on the safety of multimedia equipment Graphical symbols for use on equipment Index and synopsis Resistibility tests for telecommunication equipment exposed to overvoltage s and over currents Basic recommendation Only the English language text in the International Standard has been retained while adopting it in this Indian Standard and as such the page numbers are not the same as in the IEC Publication. For the purpose of deciding whether a particular requirement of this standard is complied with the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.

13 Doc No. LITD 07(3475) IEC TS : 2014 भ रत य म नक न टब क क पय टर क ल ए ड स बबज क आप त Indian Standard DC POWER SUPPLY FOR NOTEBOOK COMPUTERS ICS ; BIS 2014 BUREAU OF INDIAN STANDARDS MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG NEW DELHI Price Group

14 Audio. Video and Multimedia Systems and Equipments Sectional Committee. LITO 07 NATIONAL FOREWORD This Indian Standard (Fifth Revision) which is identical with IEC : 2014 DC power supply for notebook computers' issued by the International Electrotechnical Commission (IEC) was adopted by the Bureau of Indian Standards on the recommendation of the Audio, Video and Multimedia Systems and Equipments Sectional Committee and approval of the Electronics and Information Technology Division Council. The text of ISO/IEC Standard has been approved as suitable for publication as an Indian Standard without deviations. Certain conventions are, however, not identical to those used in Indian Standards. Attention is particularly drawn to the following: a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as decimal marker. In this adopted standard, reference appears to certain International Standards for which Indian Standard also exist. The corresponding Indian Standard which is to be substituted in its respective place is listed below along with its degree of equivalence for the edition indicated: International Standard Corresponding Indian Standard Degree of Equivalence IEC : 2005 Information technology equipment Safety Part 1 General requirements along with Amendment 1(2009) and Amendment 2(2013) CISPR 22 Information technology equipment - Radio disturbance characteristics Limits and methods of measurement CISPR 24, Information technology equipment Immunity characteristics Limits and methods of measurement IS (Parts 1) : 2010 Information technology equipment Safety Part 1 General requirements (Second Revision) IS 6873(Part 7):2012 Limits and methods of measurements of Radio disturbance characteristics Part 7 Information technology equipment (First Revision) DOC.LITD 9(3325) Information technology equipment - Immunity characteristics - Limits and methods of measurement(first Revision) with CISPR 22 : 2008 with CISPR 24 : 2010

15 The technical committee has reviewed the provisions of following International Standards referred in The technical committee responsible for the preparation of this standard has reviewed the provisions of the following International standards and has decided that they are acceptable for use in conjunction with this standard: International Standard Title IEC IEC 61204:1993 Connectors for electronic equipment Part 2-102: Circular connectors with assessed quality Detail specification for plugs and jacks for external low voltage power supply Low-voltage power supply devices, d.c. output Performance Characteristicsaling with Amendment 1:2001 CISPR 32 Electromagnetic compatibility of multimedia equipment Emission requirements For the purpose of deciding whether a particular requirement of this standard is complied with the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.

16 Doc No. LITD 07(3476) IEC : 2014 भ रत य म नक छ ट स म ट ममड य उपकरण क म ए ब टर च ज इ टरफ स भ ग 1 2 ममम ब र इ टरफ स Indian Standard BATTERY CHARGING INTERFACE FOR SMALL HANDHELD MULTIMEDIA DEVICES PART 1 2 mm BARREL INTERFACE ICS ; BIS 2014 BUREAU OF INDIAN STANDARDS MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG NEW DELHI Price Group

17 Audio. Video and Multimedia Systems and Equipments Sectional Committee. LITD 07 NATIONAL FOREWORD This Indian Standard which is identical with IEC (Part 1) : 2011 Battery charging interface for small handheld multimedia devices Part 1: 2 mm barrel interface' issued by the International Electrotechnical Commission (IEC) was adopted by the Bureau of Indian Standards on the recommendation of the Audio, Video and Multimedia Systems and Equipments Sectional Committee and approval of the Electronics and Information Technology Division Council. The text of ISO/IEC Standard has been approved as suitable for publication as an Indian Standard without deviations. Certain conventions are, however, not identical to those used in Indian Standards. Attention is particularly drawn to the following: a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as decimal marker. The technical committee has reviewed the provisions of following International Standards referred in The technical committee responsible for the preparation of this standard has reviewed the provisions of the following International standards and has decided that they are acceptable for use in conjunction with this standard: International Standard IEC Title Battery charging interface for small handheld multimedia devices Part 2:2 mm barrel type interface conformance testing For the purpose of deciding whether a particular requirement of this standard is complied with the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.

18 Template for comments and secretariat observations Date: Document: Project: MB/ NC 1 Line number (e.g. 17) Clause/ Subclause (e.g. 3.1) Paragraph/ Figure/ Table/ (e.g. Table 1) Type of comment 2 Comments Proposed change Observations of the secretariat 1 MB = Member body / NC = National Committee (enter the ISO 3166 two-letter country code, e.g. CN for China; comments from the ISO/CS editing unit are identified by **) 2 Type of comment: ge = general te = technical ed = editorial ISO/IEC/CEN/CENELEC electronic balloting commenting template/version page 1 of 1