CII FCAC-150 Series Relay

Transcription

1 Introducing CII Series Relay 50 Amps, 1PST/NO (DM) CII Series Relay 50 Amps, 1PST/NO (DM) with 1PDT Auxiliary Contacts

2 KEY FEATURES Non-latching relay Balanced force design Corrosion protected metal enclosure All welded hermetically sealed enclosure occupies about 1 in 3 1 Form X (SPST-NO-DM) Auxiliary versions available with 1 Form C (SPDT) aux. 6, and 28 Vdc coils available Weight: 90 grams Designed and built in accordance with MIL-PRF-6106 Rated for altitude up to 300,000 ft. Available with optional terminals and mounting styles DESCRIPTION The series relay is a polarized, single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return non-polar design. The series has a 1 Form C (SPDT) auxiliary contact set rated at 2 Amps available. Designed and built to perform under the most demanding environmental conditions and can withstand such changing environmental factors as temperature, altitude, shock, vibration, and salt spray. Minimum mechanical life expectancy is 50,000 cycles under resistive load. 3 available coil voltages (6, and 28 Vdc) with optional transient suppression. APPLICATIONS Used in military, aerospace, and associated ground support electrical and electronic systems. Principle areas of application include: - Aircraft - Missiles - Power Distribution - Fuel Pumps Avionics Main Power Feed Weapons Systems - Ground Support Equipment PART NUMBERING SYSTEM Typical Part Number or -A Y 3 Series and Contact Arrangement: = Relay with 1 Form X Main Contacts = Relay with 1 Form X Main Contacts and 1 Form C Auxiliary Contacts Terminals (see drawings for details): B = Solder Pin Coil Terminals, Stud Power Terminals C = Solder Hook Coil Terminals, Stud Power Terminals K = Terminal Block, Stud Power Terminals Enclosure (see drawings for details): R = Horizontal Flange Mount, Rotated U = Flush Vertical Flange Mount X = Horizontal Flange Mount Y = Raised Vertical Flange Mount Z = No Mount Coil: 1 = 6Vdc nominal 2 = Vdc nominal 3 = 28Vdc nominal 4 = 28Vdc nominal, with back EMF suppression Tyco Electronics I &

3 PERFORMANCE DATA Specifications Contact Data Contact Form : 1 Form X (SPST-NO-DM) : 1Form X (SPST-NO-DM) with 1 Form C (SPDT) Auxiliary Contacts Contact Rating in Amps (Continuous Duty) Type of Life (Min.) 5 Vac Load Cycles 28 Vdc 400Hz Resistive 50, Inductive (L/R=5ms) 20, Motor 20, None 100,000 Overload Current (Resistive) Max. Contact Drop at 10A Operate Time at Nominal Voltage Release Time Bounce Time Coil Data 200 A, 50 cycles Initial 150mV; After Life 175mV 15ms 15ms 1ms Coil Code Nominal Operating Voltage (Vdc) Maximum Operating Voltage (Vdc) Maximum Pick-Up Voltage at +5 C Maximum Pick-Up Voltage at +5 C, continuous current test (Vdc) Drop-Out Voltage at +5 C Maximum Coil Current at +25 C (ma) Back EMF Suppressed to (Vdc) N/A N/A N/A -42 Coil Resistance 18Ω 70Ω 290Ω 290Ω Electrical Data Initial Insulation Resistance (note 1) Insulation Resistance After Life or Environmental Test (note 1) 100 megohms, minimum, at 500Vdc, between each pin and case 50 megohms, minimum, at 500Vdc, between each pin and case Dielectric Strength At Sea Level Contacts to Ground and Between Contacts Coil to Ground Dielectric Strength at 80,000 ft (25,000m), All Points (note 4) Environmental Data Ambient Temperature Range, Operating Altitude Shock Resistance Vibration Resistance, Sinusoidal Mechanical Data Approximate Weight 1,250Vrms, 60 Hz. 1,000Vrms, 60 Hz. 500Vrms, 60 Hz -70 C to +5 C 300,000 feet 50 G s, ms. 20 G s, Hz. 3.2 oz. (90g) Max. NOTES 1. All wired terminals must be connected together during this test. Dielectric withstanding voltage and insulation resistance are measured between all mutually insulated wired terminals and between all these terminals and case. Tyco Electronics I &

4 FOR MORE INFORMATION Technical Support Internet: USA: +1 (800) Canada: +1 (905) Mexico: +1 (800) C. America: +52 (0) South America: +55 (0) Hong Kong: +852 (0) Japan: +81 (0) Great Britain: +44 (0) France: +33 (0) Germany: +49 (0) Italy: +39 (0) India: +91 (0) Tyco Electronics Corporation Harrisburg, PA tycoelectronics.com Copyright 2008 Tyco Electronics Corporation M GADM/FP /08 CII, TE LOGO and TYCO ELECTRONICS are trademarks.

5 TERMINALS B Solder Pin Terminals Tin/Lead Plated C Solder Hook Terminals Tin/Lead Plated.062±.002 DIA PINS 2 PLCS).062±.002 DIA PINS (5 PLCS).062±.002 DIA HOOKS 2 (PLCS).062±.002 DIA HOOKS (5 PLCS) K Terminal Shield GOLD PIN TERMINALS FOR MIL-C-39029/22B 192 SOCKET PINS Terminal View GOLD PIN TERMINALS FOR MIL-C-39029/22B 192 SOCKET PINS DC Coils Terminal Wiring DC Coils w/transient Suppression & I Tyco Electronics

6 PRODUCT OUTLINE DIMENSIONS The standard terminal types and enclosures are illustrated below with dimensions in inches ± and (millimeters ±0.25). representative drawings are shown below. "U" "Y" MAX MAX FULL R 6 PLCS.156 "X" "R" "Z" FULL R 6 PLCS MAX & I Tyco Electronics