Certificate of Compliance

Transcription

1 Certificate of Compliance Certificate: (LR ) Master Contract: Issued to: Industrial Monitoring Instr. (IMI) A Div. of PCB Piezotronics, Inc Walden Ave Depew, NY USA Attention: Nick Fulciniti The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent indicator 'US' for US only or without either indicator for Canada only. Issued by: Richard Dibler Jr. Richard Dibler Jr. PRODUCTS CLASS CLASS PROCESS CONTROL EQUIPMENT - Intrinsically Safe, Entity - For Hazardous Locations - PROCESS CONTROL EQUIPMENT - Intrinsically Safe, Entity - - For Hazardous Locations - Certified to US Standards Class I, Div. 1, Groups A, B, C and D; Class II, Div. 1, Groups E, F and G; Class III, Div 1: Exia IIC T4: AExia IIC T4: - Model EX602D0x, EX603C0x, EX606B0x and EX607A0x Vibration Sensors, input rated 28V dc max, 20mA; intrinsically safe with entity parameters of: Ui (Vmax) = 30 V, Ii (Imax) = 200 ma, Pi = 1W, Ci = 16.2 nf, Li = 0; when installed per installation dwg ; Temp. Code Max. Ambient 121 Deg. C. - Model EX602D1x, EX603C1x, EX606B1x, EX607A1x and EX608A1x Vibration Sensors, input rated 28V dc max, 20mA; intrinsically safe with entity parameters of: Ui (Vmax) = 30 V, Ii (Imax) = 200 ma, Pi = 1W, Ci = 77.2 nf, Li = 305 uh; when installed per installation dwg ; Temp. Code Max. Ambient 121 Deg. C.

2 - Model EX602D6x, EX603C6x, EX606B6x and EX607A6x Vibration Sensors, input rated 28V dc max, 20mA; intrinsically safe with entity parameters of: Ui (Vmax) = 30 V, Ii (Imax) = 200 ma, Pi = 1W, Ci = 77.2 nf, Li = 305 uh; when installed per installation dwg ; Temp. Code Max. Ambient 121 Deg. C. - Model Vibration Sensors, input rated 28 Vdc max, 20 ma max; intrinsically safe with entity parameters of: Ui (Vmax) = 30V, Ii (Imax) = 200mA, Pi = 1W, Ci = 16.2 nf, Li = 0; when installed per installation Dwg ; Temp. Code Max Ambient 121 Deg C. Note: The x in the model code may be any number from 0 to 9, which denotes variations in sensor sensitivity. Model EXab602cde, EXab603cde, EXab606cde, EXab607cde, EXab608cde Vibration Sensors, input rated 28 Vdc Max, 20mA, intrinsically safe with entity parameters of: Ui (Vmax) = 28 V, Ii (Imax) = 93 ma, Ci = nf, Li = µh; when installed per installation drawing 45279; Temp Code Max. Ambient 121 ºC Where: a = TO or blank where TO is Temperature Output Option b = M or blank where M is Metric stud option c = any alpha digit as follows dealing with changes not affecting the certification: E-Z for EX602 series D-Z for EX603 series C-Z for EX606 series B-Z for EX607 and EX608 series d = any numeric digit denoting connector style or integral cable e = and numeric digit denoting variations in sensor sensitivity CLASS PROCESS CONTROL EQUIPMENT - Intrinsically Safe and Non-Incendive Systems - For Hazardous Locations

3 CLASS PROCESS CONTROL EQUIPMENT - Intrinsically Safe and Non-Incendive Systems - For Hazardous Locations - CERTIFIED TO U.S. STANDARDS Class I, Div. 2, Groups A, B, C and D: ExnL IIC T4: AExnA IIC T4: - Model EX602D0x, EX603C0x, EX606B0x and EX607A0x Vibration Sensors, input rated 28V dc max, 20mA; non-incendive with entity parameters of: Ui (Vmax) = 30 V, Ii (Imax) = 200 ma, Pi = 1W, Ci = 16.2 nf, Li = 0; when installed per installation dwg ; Temp. Code Max. Ambient 121 Deg. C. - Model EX602D1x, EX603C1x, EX606B1x, EX607A1x and EX608A1x Vibration Sensors, input rated 28V dc max, 20mA; non-incendive with entity parameters of: Ui (Vmax) = 30 V, Ii (Imax) = 200 ma, Pi = 1W, Ci = 77.2 nf, Li = 305 uh; when installed per installation dwg ; Temp. Code Max. Ambient 121 Deg. C. - Model EX602D6x, EX603C6x, EX606B6x and EX607A6x Vibration Sensors, input rated 28V dc max, 20mA; non-incendive with entity parameters of: Ui (Vmax) = 30 V, Ii (Imax) = 200 ma, Pi = 1W, Ci = 77.2 nf, Li = 305 uh; when installed per installation dwg ; Temp. Code Max. Ambient 121 Deg. C. Model EXab602cde, EXab603cde, EXab606cde, EXab607cde, EXab608cde Vibration Sensors, input rated 28 Vdc Max, 20mA, non-incendive with entity parameters of: Ui (Vmax) = 28 V, Ii (Imax) = 93 ma, Ci = nf, Li = µh; when installed per installation drawing 45279; Temp Code Max. Ambient 121 ºC Where: a = TO or blank where TO is Temperature Output Option b = M or blank where M is Metric stud option c = any alpha digit as follows dealing with changes not affecting the certification: E-Z for EX602 series D-Z for EX603 series C-Z for EX606 series B-Z for EX607 and EX608 series

4 d = any numeric digit denoting connector style or integral cable e = and numeric digit denoting variations in sensor sensitivity Notes: 1. For Canadian Installations, sensor case must be bonded to ground according to Section of the CEC, Part For US Installations, sensor case must be bonded to ground according to Article of the NEC. 3. The x in the model code may be any number from 0 to 9, which denotes variations in sensor sensitivity. CLASS PROCESS CONTROL EQUIPMENT - Intrinsically Safe and Non-Incendive Systems - For Hazardous Locations CLASS PROCESS CONTROL EQUIPMENT - Intrinsically Safe and Non-Incendive Systems - For Hazardous Locations - CERTIFIED TO U.S. STANDARDS Class I, Div. 2, Groups A, B, C and D: ExnL IICT4: - Model Vibration Sensor, input rated 28 Vdc max, 20 ma max; non-incendive when connected to CSA Certified Power/Signal Monitoring units when installed per installation Dwg ; Temp. Code Max Ambient 121 Deg C. Note: Sensor case must be bonded to ground according to Section of the CEC, Part 1 and according to Article of the NEC as applicable. APPLICABLE REQUIREMENTS Class & CSA Std C22.2 No. 142-M Process Control Equipment

5 CAN/CSA-C22.2 No Intrinsically Safe and Non-Incendive Equipment for Use in Hazardous Locations UL Std No Intrinsically Safe Apparatus and Associated Apparatus for Use in Class I, II and III, Division 1, Hazardous Locations UL Std No Energy Management Equipment CAN/CSA-E :02 - Electrical Apparatus for Explosive Gas Atmospheres, Part 0: General Requirements CAN/CSA- E :02 - Electrical apparatus for explosive gas atmospheres, Part 11: Intrinsic Safety i ANSI/UL :02 - Electrical Apparatus for Explosive Gas Atmospheres - Part 0: General Requirements ANSI/UL :02 - Electrical Apparatus for Explosive Gas Atmospheres - Part 11: Intrinsic Safety i Class & CSA Std C22.2 No. 142-M Process Control Equipment CSA Std C22.2 No. 213-M Non-Incendive Electrical Equipment for Use in Class I, Division 2 Hazardous Locations UL Std No Energy Management Equipment UL Std. No Electrical Equipment for Use in Class I and II, Division 2; Class III Hazardous (Classified) Locations FM Std. No Electrical Equipment for Use in Hazardous (Classified) Locations General Requirements FM Std. No Nonincendive Electrical Equipment for Use in Class I and II, Division 2, and Class III, Divisions 1 and 2, Hazardous (Classified) Locations CAN/CSA- E :02 - Electrical apparatus for explosive gas atmospheres, Part 15: Type of Protection n ANSI/UL :02 - Electrical Apparatus for Explosive Gas Atmospheres - Part 15: Type of Protection n. MARKINGS Markings are etched directly into the Sensor enclosure body. The following marking details appear: I.S. models - CSA Monogram with C US Indicator - Submitter Identification - Model Number

6 - Serial Number, Date Code or Month and Year of Manufacture - Electrical Rating - Hazardous Location Designation (ie the symbol Exia IIC T4 and AExia IIC T4) - Certificate # reference (ie ) - Reference to Installation Instructions Div. 2 Non-Incendive models - CSA Monogram with C US indicator. - Submitter Identification - Model Number - Serial Number, Date Code or Month and Year of Manufacture - Electrical Rating - Hazardous Location Designation (ie Ex nl IICT4, AEx na IICT4, Class I, Div. 2, Groups A, B, C and D) - Certificate # reference (ie ) Note - Jurisdictions in Canada may require these markings to also be provided in French language. It is the responsibility of the manufacturer to provide bilingual marking, where applicable, in accordance with the requirements of the Provincial Regulatory Authorities. It is the responsibility of the manufacturer to determine this requirement and have bilingual wording added to the "Markings".