TITLE: SPECIFICATION NO. PE-MSE-VD-ACC VOLUME:
|
|
- Agatha Perkins
- 5 years ago
- Views:
Transcription
1 (For Vendor Registration Purpose) SHEET 1 of GENERAL INFORMATION The general guidelines as illustrated in the subsequent clauses of this section shall be applicable for air cooled condenser to be procured under the scope of this package. This specification is intended only for vendor registration purpose. Project specific specification indicating detailed scope, materials of construction, process parameters like Steam turbine exhaust flow, steam turbine exhaust pressure, enthalpy, inlet air dry bulb temperature, heat load etc. shall be made available to the registered vendors at the time of NIT. Note : Any Data Sheet/ QP/ Annexure/ Section / Part of specification etc. indicated in this document but not attached shall be made available to the registered vendors at the time of NIT CODES AND STANDARDS In addition to the requirements spelt out elsewhere in the specification, the equipment to be provided under this section shall specifically conform to the following codes, standards, specifications and regulations, as applicable, including all the latest amendments subsequent to the year of publication as mentioned below Anti-Friction Bearing Manufacturer s Association: Std 9 & American Gear Manufacturer s Association: 6001-C & American Institute of Steel Construction: M011, S302 & S American National Standards Institute: A58.1, B1.1, B & B American Petroleum Institute : Std American Society of Mechanical Engineers : ASME Sec VIII Div Heat Exchange Institute : Standards for Steam Surface Condenser, 9th edition,1995
2 (For Vendor Registration Purpose) SHEET 2 of API-610/1989: Centrifugal pumps for general refinery services HIS: Hydraulic Institute Standards, USA TEMA : Standards Tubular Exchanger Manufacturers association ASTM Standard Methods for Liquid Penetration Inspection Performance Test Codes for air cooled heat exchangers : PTC 30 Note : For piping, valves, fans, motors, ejectors/ vacuum pumps, tanks, civil works, electrical and C&I works etc., the latest Indian/ International standards shall be applicable SCOPE OF SUPPLY & SERVICES: The ACC scope shall be project specific & detailed specification shall be furnished during project specific enquiry, however for reference the scope has been indicated in succeeding clauses The EPC scope for ACC includes the complete ACC including design, engineering, manufacture, assembly, painting, inspection and testing at manufacturer's and/or his sub-contractor's work, proper packing, delivery at site, transportation, unloading/ handling at site, erection, site painting, commissioning, performance testing at site for Air Cooled Condenser (ACC) including mechanical, electrical, C&I, civil and structural works, as specified & as necessary for completeness in all respects and for efficient & trouble free operation of ACC The ACC under this specification shall be complete with standard/special accessories. The scope of supply shall include, but not limited to the following: Standard accessories for ACC: a) Steam duct from turbine exhaust flange to condenser including expansion joints, guides, manholes, anchors and hangers and provision for HP and LP
3 Tanks TITLE: SPECIFICATION NO. PE-MSE-VD-ACC (For Vendor Registration Purpose) SHEET 3 of 6 bypass steam dump. The turbine exhaust is a flange connection and ACC duct will be provided with flanged connection. b) Steam distribution ducting c) Fin tube bundles d) Condensate collection headers e) Air moving system including fans, gearboxes, couplings, motors, vibration switches, fan rings and guards. f) Support structures for steam duct, guides, slides etc g) Fan deck and A-frames including maintenance platforms, access stairways and escape ladder. h) Partition walls, access doors, and wind wall, steel support framing including associated siding material. i) Condensate and non-condensable removal piping within the condenser envelope. j) Rupture disk assemblies (100 % capacity). k) Dump Tube & Accessories for Turbine Bypass Steam Dumping. l) Noise attenuation features/devices as required. m) All bolting and gaskets required for assembly of materials furnished like structures, fans and pumps n) Mandatory spares shall be project specific & shall be furnished during project specific enquiry. a) One (1) hot well tank(main condensate tank), for the air cooled condenser system complete with supporting structure, nozzles and flanges, stiffeners, baffle plates, condensate level control etc.
4 Pumps TITLE: SPECIFICATION NO. PE-MSE-VD-ACC (For Vendor Registration Purpose) SHEET 4 of 6 b) One (1) condensate drain pot for collecting the condensate of the turbine exhaust duct complete with all supporting structure, nozzles, stiffeners, control & instruments etc. a) Two (2)x100% drain pot pumps each equipped with direct coupled motor and all necessary accessories. The pump shall be sized considering all condensate / drain flow from turbine and other sources. b) Horizontal Condensate Extraction Pumps with motors Piping, Fittings and Ducts a) The required piping and ducting from turbine exhaust to condenser, condensate piping from condenser to main condensate tank, air removal piping as well as all other necessary piping including drain and vent piping are included in Bidder s scope. b) Motorized Valves at Condensate Extraction Pump and Condensate drain Pump Hot well Pumps discharge. c) Condensate Extraction Pump minimum recirculation system including Control Valves., inlet / outlet isolating valves and by-pass valves. d) Insulation on Tanks, Ducting & Piping as applicable. e) DC Solenoid Vacuum Breaker Valves mounting on Condenser ACC Cleaning System Bidder shall include a suitable cleaning system with high pressure water jet for ACC outside heat transfer surface in his scope Air Removal System a) 2x100% steam jet holding ejectors b) 1x100% hogging ejector
5 (For Vendor Registration Purpose) SHEET 5 of 6 c) 1x100% ejector condensers consisting of inter and after condensers cooled by main condensate. d) Thermal relief valve on the water side. e) Drain and Vent piping, valves and traps with supports Note : Vacuum pump may be asked in place of ejectors. Same shall be indicated in project specific enquiry Services included in Bidder s Scope: Brief Scope supply of Civil Works a) All civil works including equipment foundation of all equipments, support columns / structures, operating floors, pump houses with handling arrangements, grouting, Cable trenches, floor drains, within ACC Vendor T.P. s. b) Wind Wall structure all round the ACC to avoid air recirculation. c) Staircase, all Platforms, Columns, Fan Deck, Deck Slab, ACC Walkway and any other Civil Work etc Brief Scope supply of Electrical & C & I Works: a) Electrification, illumination, lighting, over ground earthing & underground earthing, lightning protection system etc. b) Instrument Panel for instrument supplied by ACC Vendor. c) Local instrumentation and controls in the exhaust and condensate systems required for safe and reliable operation including control cabling and cable trays up to Junction box Erection and commissioning of ACC at site Performance testing of ACC at site as per Quality Plan/ performance test procedure (QP/ performance test procedure shall be approved by BHEL and end customer) The omission of specific reference to any component / accessory necessary for the proper performance of ACC and its Components shall be in Vendor scope Terminal Points:
6 (For Vendor Registration Purpose) SHEET 6 of 6 a) Counter Flange for Turbine exhaust hood flange. ( TG Counter Flange in BHEL Scope ) b) Aux. Steam to ejectors : At one point near ejectors, ejector in ACC Vendor Scope. c) Condensate Piping for exhaust hood Spray from CEP discharge shall be at one point near TG Deck. d) DM make up Water to hot well : at inlet nozzle of Hot well / Condensate Tank. e) Instrument Air / Service Air: At one point near ACC area. f) Power Supply : At motor terminals. g) Instruments: At local JBs near equipment. Local JB s in ACC Vendor scope. h) Main Condensate supply & return for GSC : TP on main condensate line near GSC outlet, Isolating & bypass valve in ACC Vendor scope. i) Drains & Vents of STG integral portion : At Valve outlet. Piping by ACC Vendor Note : A schematic diagram is attached as Annexure-A for terminal points between BHEL & bidder. This is for general reference of scope, however the detailed scope shall be indicated in project specific enquiry OTHER REQUIREMENTS: The detailed technical/ constructional requirements shall be as per project specific enquiry The performance requirements and inspection/ testing shall be as per project specific enquiry DRAWINGS/ DOCUMENTS DISTRIBUTION SCHEDULE After award of LOI, the successful bidder shall submit drawings/documents as per project specific enquiry The no. of drawings/documents to be submitted shall be as per project specific enquiry. Note: Evaluation of bids, guarantees etc shall be as per project specific enquiry.
7
Design and analysis of the piping systems
Design and analysis of the piping systems Over all schematic diagram of the total system along with equipment and connecting piping is shown in Fig.. Different piping systems are described as follows:.
More informationENGINEERING SPECIFICATION ASU TYPE NITROGEN GENERATION UNIT FOR DIESEL HYDROTREATER UNIT FOR HINDUSTAN PETROLEUM CORPORATION LTD.
ENGINEERING SPECIFICATION FOR DIESEL HYDROTREATER UNIT FOR HINDUSTAN PETROLEUM CORPORATION LTD. VISAKH REFINERY DHT PROJECT TEIL JOB NO. : 6261 DOCUMENT NO: 6261- A - 95-48 -051 A 16-March-09 For Client
More informationIndian National Trust for Art and Cultural Heritage (INTACH, 71, KK Birla Lane, Lodhi Estate, New Delhi , Ph. No.
Indian National Trust for Art and Cultural Heritage (INTACH, 71, KK Birla Lane, Lodhi Estate, New Delhi -110003, Ph. No. 011-49854100 TENDER NOTICE Sealed tender in two separate bids a) Technical bids,
More informationTENDER DOCUMENT FOR SUPPLY OF EPOXY MIXING & POURING PLANT
BHARAT HEAVY ELECTRICALS LTD., CORPORATE R&D DIVISION VIKAS NAGAR, HYDERABAD-500093 (INDIA) Enquiry : Date : PURCHASE SECTION TECHNICAL SECTION SPEC.NO. 91 40 2377 8474 PHONE 91 40 2377 4494 Ext.7326 ST:ICH:08:001
More information10 th Annual ACC User Group Meeting
10 th Annual ACC User Group Meeting Colorado Springs, CO Oct 8-11, A Vacuum Leak Odyssey Presented by Don Wright 2018 Exelon Generation Company, LLC. All rights reserved. Combined Cycle Plant Configuration
More informationN N O V A T I O N E F F I C I E N C Y Q U A L I T Y LS BARGE PUMP. Vertical high-flow pump
N N O V A T I O N E F F I C I E N C Y Q U A L I T Y LS BARGE PUMP LS BARGE For more than 60 years the name Ruhrpumpen has been synonymous worldwide with innovation and reliability for pumping technology
More information1.1 This section applies to air handling units for HVAC Systems.
AIR HANDLING UNITS GENERAL INFORMATION 1.1 This section applies to air handling units for HVAC Systems. DESIGN REQUIREMENTS 2.1 Design Criteria a. The decision to use modular central station air handling
More information2x58 MW Coal Fired Power Plant at Mauritius
2x58 MW Coal Fired Power Plant at Mauritius The coal-fired power plant produces electricity by the burning of coal and air in a Circulating Fluidized Bed Combustion Boiler (CFBC), where it heats water
More informationSECTION STEAM CONDENSATE PUMPS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 23 22 23 STEAM CONDENSATE PUMPS SPEC WRITER NOTES: 1. Delete between // ---- // if not applicable to project. Also delete any other item or paragraph not applicable
More informationBuildingName The Description of the Project P DOCUMENTS
ARCHITECTURE, ENGINEERING AND CONSTRUCTION P00000000 0000 DOCUMENTS ARCHITECTURE & ENGINEERING 326 East Hoover, Mail Stop B Ann Arbor, MI 48109-1002 Phone: 734-764-3414 Fax: 734-936-3334 SPECIFICATION
More informationPart: I TECHNICAL SPECIFICATION
Part: I TECHNICAL SPECIFICATION GUJARAT ENERGY TRANSMISSION CORPORATION LTD. TECHNICAL SPECIFICATIONS FOR THE WORK OF DESIGN, SUPPLY, ERECTION AND COMMISSIONING INCLUDING CIVIL WORK OF NITROGEN INJECTION
More informationBASIL 6000 TUNNEL CAGE WASHER
BASIL 6000 TUNNEL CAGE WASHER APPLICATION For thorough, efficient cleaning of cages, debris pans, bottles, feeder bowls, and miscellaneous items used in the care of laboratory animals. DESCRIPTION The
More informationTECHNICAL SPECIFICATIONS
. MOL Group TECHNICAL SPECIFICATIONS MECHANICAL List of booklets MGS - M - REF M LI Rev 1.00.00 This document is property of MOL Group. The use is only allowed with the written permission of MOL Group.
More informationEEMUA E Learning and Publications Catalogue
EEMUA E Learning and Publications Catalogue E learning courses and publications can be purchased online at https://www.eemua.org/shop.aspx Alternatively, please contact EEMUA by telephone +44 (0)20 7488
More informationPurchase Qualification Requirement (PQR)
Purchase Qualification Requirement (PQR) The vendor is required to meet the provenness criteria of critical equipment, auxiliaries, systems and bought out items for a 660MW rating TG sets as per criteria
More informationTECHNICAL SPECIFICATION FOR OZONE GENERATION PLANT REV 00
1x370MWYELAHANKACOMBINEDCYCLEPOWERPLANT KARNATAKAPOWERCORPORATIONLIMITED TECHNICALSPECIFICATIONFOR OZONEGENERATIONPLANT REV00 VOLUME IIB&III SPECIFICATIONNO.:PETS40917414000AA001 BHARATHEAVYELECTRICALSLIMITED
More informationOPERATING AND MAINTENANCE MANUAL FOR PLATE HEAT EXCHANGER INDIRECT FIRED WATER HEATER. Electric Heater Company Base Model "BWXP"
OPERATING AND MAINTENANCE MANUAL FOR PLATE HEAT EXCHANGER INDIRECT FIRED WATER HEATER Electric Heater Company Base Model "BWXP" HUBBELL ELECTRIC HEATER COMPANY P.O. BOX 288 STRATFORD, CT 06615 PHONE: (203)
More informationDOCUMENT TABLE OF CONTENTS
DOCUMENT 00003 June 16, 2005 TABLE OF CONTENTS DOCUMENT NO. INTRODUCTORY INFORMATION DOCUMENT 00003 TABLE OF CONTENTS DIVISION 1 GENERAL REQUIREMENTS SECTION 01011 SECTION 01025 SSP21.1-1 SECTION 01026
More informationCONTENTS. B. System Design and Performance Requirements
15625 Water Chillers This document provides design standards only, and is not intended for use, in whole or in part, as a specification. Do not copy this information verbatim in specifications or in notes
More informationDIVISION 23 HVAC Hydronic Piping Systems
General Information Programming/ Design Bidding/ Preconstruction Installation/ Construction Closeout/ Warranty QA/QC Checklist Construction Services DIVISION 23 HVAC 23 21 13 Hydronic Piping Systems 01
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10438-1 Second edition 2007-12-15 Petroleum, petrochemical and natural gas industries Lubrication, shaft-sealing and control-oil systems and auxiliaries Part 1: General requirements
More informationAnnex A-8 CONCENTRATED SOLAR POWER UNITS INDEX TO SYSTEM/COMPONENT CAUSE CODES
Annex A-8 CONCENTRATED SOLAR POWER UNITS INDEX TO SYSTEM/COMPONENT CAUSE CODES SOLAR ENERGY GATHERING EQUIPMENT Solar Field 6500-6559 Thermal Storage 6570-6589 Operational Problems 6590-6599 STEAM TURBINE
More informationSECTION COOLING TOWERS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 23 65 00 COOLING TOWERS SPEC WRITER NOTES: 1. DELETE BETWEEN //---// if not applicable to project. Also delete any other item or paragraph not applicable in the
More informationSTANDARD TECHNICAL SPECIFICATION FOR PRESSURE SWITCH, DIFFERENTIAL PRESSURE SWITCH VOLUME - IIB. SPECIFICATION No: PES
STANDARD TECHNICAL SPECIFICATION FOR PRESSURE SWITCH, DIFFERENTIAL PRESSURE SWITCH VOLUME - IIB SPECIFICATION No: PES-145-031 BHARAT HEAVY ELECTRICALS LIMITED POWER SECTOR PROJECT ENGINEERING MANAGEMENT
More informationBharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirapalli , TAMIL NADU, INDIA MATERIALS MANAGEMENT / CAPITAL EQUIPMENT
An ISO 9001 Company Bharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirapalli 620014, TAMIL NADU, INDIA MATERIALS MANAGEMENT / CAPITAL EQUIPMENT ENQUIRY NOTICE INVITING TENDER Phone:
More informationSECTION HVAC TABLE OF CONTENTS PART 1 - SYSTEM DESCRIPTION / OUTLINE SPECIFICATIONS FILED SUB BID PROJECT OVERVIEW...
SECTION 230001 TABLE OF CONTENTS SECTION 230001 PART 1 - SYSTEM DESCRIPTION / OUTLINE SPECIFICATIONS... 1 1.00 FILED SUB BID... 1 1.01 PROJECT OVERVIEW... 2 1.02 DESIGN CRITERIA... 4 1.03 CODE ISSUES...
More informationSECTION AIR COOLED WATER CHILLERS
PART 1 GENERAL 1.1 SECTION INCLUDES A. Chiller package B. Charge of refrigerant and oil C. Controls and control connections D. Chilled water connections E. Starters F. Electrical power connections 1.2
More informationC. ASSE 1013: Performance Requirements for Reduced Pressure Principle Backflow Preventers.
SECTION 22 10 00 PLUMBING PIPING AND PUMPS PART 1 - GENERAL 1.1 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design.
More informationTitle: YALE OFFICE OF FACILITIES PROCEDURE MANUAL Chapter: 01 - Yale Design Standard Division: HVAC Standards
Date Description of Change Pages / Sections Modified ID 6/15/16 Entire document - mgl44 PART 1 - INTRODUCTION 1.1 PURPOSE A. This section is intended to define the general installation and minimum product
More informationD-8 OUTLINE SPECIFICATION FOR HTHW HEAT EXCHANGERS
D-8 OUTLINE SPECIFICATION FOR HTHW HEAT EXCHANGERS GENERAL: This document provides performance requirements and guideline information for Heat Exchanger equipment for Colorado College only, and is not
More informationLIQUID RING PUMPS FOR THE POWER INDUSTRY
LIQUID RING PUMPS FOR THE POWER INDUSTRY VACUUM SOLUTIONS FOR THE POWER PLANT for The Power Industry 334 Shop online at shop.edwardsvacuum.com Contact our customer service team for the Power Industry 333.
More informationC. ASME Compliance: Fabricate and label water chiller heat exchangers to comply with ASME Boiler and Pressure Vessel Code: Section VIII, Division 1.
SECTION 236426 - ROTARY-SCREW WATER CHILLERS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes packaged, water cooled or air cooled as scheduled, electric-motor-driven, rotary-screw water chillers
More informationPOWERENERGY
ASME 2016 POWER CONFERENCE JUNE 26 JUNE 30, 2016 CHARLOTTE, NORTH CAROLINA, USA POWERENERGY2016-59067 EVACUATION SYSTEMS FOR STEAM SURFACE CONDENSERS: VACUUM PUMPS OR STEAM JET AIR EJECTORS? Ranga Nadig,
More informationALZ GmbH. air cooled systems and air heaters. Competent Partners
ALZ GmbH air cooled systems and air heaters Competent Partners Company overview We would like to introduce ourselves as your competent partner in heat transfer. Since 1990 the ALZ GmbH designs and manufactures
More informationAPPENDIX J ILLUSTRATIONS
The following figures have been included in the 1994 edition of the Standard Plumbing Code to aid in interpreting this code. The figures are not to be construed as superseding the written text, but merely
More informationDENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION PUMPS
PART 0 A/E INSTRUCTIONS 0.01 Design Requirements A. Pumping system design 1. A primary-secondary pumping system is preferred. Redundant pipes are required for chillers and boilers. 2. Select pumps to operate
More informationSECTION DOMESTIC WATER PRESSURE BOOSTING SYSTEMS (VFD) PART 1 - GENERAL 1.1 SUMMARY
SECTION 22 11 23.13 DOMESTIC WATER PRESSURE BOOSTING PART 1 - GENERAL 1.1 SUMMARY A. Where utility water pressure cannot adequately meet the pressure requirements of the domestic water systems and where
More informationInstallation of Glass Lined Equipment
Installation of Glass Lined Equipment Information given herein is for guidance only and may not be complete. It is important that only trained and competent personnel are permitted to handle glass lined
More informationSTANDARD TECHNICAL SPECIFICATION FOR LEVEL SWITCH (FLOAT/DISPALCER TYPE) VOLUME - IIB. SPECIFICATION No: PES
STANDARD TECHNICAL SPECIFICATION FOR LEVEL SWITCH (FLOAT/DISPALCER TYPE) - IIB SPECIFICATION No: PES-145-033 BHARAT HEAVY ELECTRICALS LIMITED POWER SECTOR PROJECT ENGINEERING MANAGEMENT DIVISION NOIDA,
More informationE. Baffle Tray Column (or, Termed Shower Deck, No Holes, Caps, or Other Contact Devices)
252 Applied Process Design for Chemical and Petrochemical Plants E. Baffle Tray Column (or, Termed Shower Deck, No Holes, Caps, or Other Contact Devices) For counter flow, gas flowing up a column through
More informationSANTA ROSA FIRE DEPARTMENT FIRE PREVENTION BUREAU PLAN REVIEW CHECKLIST
July 1, 2010 SANTA ROSA FIRE DEPARTMENT FIRE PREVENTION BUREAU PLAN REVIEW CHECKLIST FIRE PUMP REVIEW Address: Permit #: Inspector: Date: Status: Inspector: Date: Status: A-Approved; AC-Approved w/comments;
More informationSECTION COOLING TOWERS
SECTION 23 65 00 COOLING TOWERS PART 1 - GENERAL 1.1 DESCRIPTION A. Packaged, induced draft open circuit cooling tower complete with fill, fan, inlet louvers and associated accessories and equipment. 1.2
More informationAir Handling Units. T F E.
Air Handling Units Extract from BS EN ISO 15138:2007 Petroleum & natural gas industries- Offshore production installations-heating, ventilation & air-conditioning. A.12.1 Function Installations provided
More informationInstallation, Operation and Maintenance LOK-FLANGE Multitube Heat Exchangers
Bulletin 1200/4 (Revised 5/12) Installation, Operation and Maintenance LOK-FLANGE Multitube Heat Exchangers INNOVATORS IN HEAT TRANSFER I. INSTALLATION OF HEAT EXCHANGERS A. HEAT EXCHANGER SETTINGS 1)
More informationHEAT EXCHANGE INSTITUTE, INC.
HEAT EXCHANGE INSTITUTE, INC. STANDARDS for STEAM SURFACE CONDENSERS ELEVENTH EDITION Copyright October 2012 by Heat Exchange Institute 1300 Sumner Avenue Cleveland, Ohio 44115-2851 Reproduction of any
More informationMedupi Unit 6 ACC hot cleaning: Method and results
Medupi Unit 6 ACC hot cleaning: Method and results Johannes Pretorius and Pieter Rosslee China International ACC user s group meeting 13-16 October 2015 Overview Background Medupi ACC hot cleaning - general
More informationWD7664 / WD7663 Maxon Burner. Ellis Whisper Dryer Installation & Start UP
Title WD7664 / WD7663 Maxon Burner Ellis Whisper Dryer Procedure No. Installation & Start UP Procedure Author Chris Giordano Effective 1/23/17 Revision A Submitted By Chris Giordano Supersedes Date Revision
More informationMINIMUM TANK GAP. Greater of 3 or one-sixth of sum of adjacent tank diameters. one-half of sum of adjacent tank diameters 20
Piping Layout Design Introduction The performance requirements of the equipment are developed by design teams which normally include members from the different departments such as process, engineering,
More informationINVITATION FOR QUOTATION. TEQIP-II/2015/RJ1G08/Shopping/25
INVITATION FOR QUOTATION TEQIP-II/2015/RJ1G08/Shopping/25 04-Aug-2015 To, "firm name and address" Sub: Invitation for Quotations for supply of Goods Dear Sir, 1. You are invited to submit your most competitive
More informationUpdate In Progress. Division 23 Heating, Ventilation, and Air Conditioning Page Section FLUID SYSTEMS EQUIPMENT PART 1 GENERAL
Section 23 20 00 FLUID SYSTEMS EQUIPMENT PART 1 GENERAL 1. CHILLERS Page 23 20 00-1 A. Provide chiller packages with centrifugal compressors, or screw compressors, and water cooled condensers. B. Design
More informationS&T HEAT EXCHANGERS Part II: Main Parts, Conical Transitions, Shell & Heads, Nozzle Design.
S&T HEAT EXCHANGERS Part II: Main Parts, Conical Transitions, Shell & Heads, Nozzle Design. STUDY NOTES Instructor: Javier Tirenti training@arvengconsulting.com www.arvengconsulting.com Table of contents
More informationA. Air Handling Units shall be designed to the specific requirements of the application: Recirculation or 100% Makeup.
SECTION 23 70 00- CENTRAL HVAC EQUIPMENT PART 1: GENERAL 1.1 PURPOSE: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design.
More informationREFRIGERANT PIPING SYSTEM
PART 1 GENERAL 1.01 DESCRIPTION A. The requirements of this section apply to the refrigerant piping system connecting refrigeration and HVAC equipment specified in other sections of these specifications.
More informationSECTION GENERAL-SERVICE COMPRESSED-AIR SYSTEMS
PART 1 GENERAL 1.01 SECTION INCLUDES A. Pipe and Pipe Fittings. B. Air compressor. C. Air receiver and accessories. D. Aftercooler. E. Refrigerated air dryer. F. Pressure reducing station. 1.02 RELATED
More informationSilhouette. Feedwater Heater. Boiler Feedwater
Roth Roth Low Low Silhouette Silhouette TRAY DEAERATORS Boiler Boiler Feedwater Feedwater Heater Heater Capacities Capacities to to 50,000 50,000 lb/hr lb/hr Model RDTV-150-5-1-2 vertical tray type deaerator
More informationB. Product Data: Provide manufacturers catalogue information. Indicate valve data and ratings.
DIVISION 21 21 05 00 COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe, fittings, sleeves, escutcheons, seals, and connections for sprinkler systems. 1.2 RELATED REQUIREMENTS
More informationCopperad. Copperad Fan Convectors (November 2005 onwards) Installation, Operation and Maintenance Instructions To be retained by the user
Copperad Fan Convectors (November 2005 onwards) Installation, Operation and Maintenance Instructions To be retained by the user Copperad QA/IOM/58 Issue 2 1 GENERAL 1.1 GENERAL DESCRIPTION This manual
More informationHEAT GENERATION 1.01 RELATED CORNELL DESIGN AND CONSTRUCTION STANDARDS. B. Section HVAC Basic Materials and Methods
230520 HEAT GENERATION Cornell s Design and Construction Standards provide mandatory design constraints and acceptable or required products for all construction at Cornell University. These standards are
More informationCOBB COUNTY SCHOOLS /S&A % BID DOCUMENTS 2/18/11 SECTION SPRINKLER SYSTEM
SECTION 21 10 00 PART 1 - GENERAL 1.1 CODES A. Work shall conform to NFPA 13 Sprinkler Systems, 2002 Edition and NFPA 24 Outside Protection, 2002 Edition. NFPA 14 Standpipe Systems, 2000 Edition and International
More informationLN series STERLING PUMPS. Horizontal Split Case Pumps. Double Volute. Single Stage.
LN series Horizontal Split Case Pumps Double Volute. Single Stage www.sterlingpumps.com.au LN series Sizes: 6 to 42 Capacity to 12,500 m³/h Heads to 190 metres A rugged, single stage, double volute horizontal
More informationRiverside County Fire Department Office of the Fire Marshal Market St., Ste. 150, Riverside, CA Ph. (951) Fax (951)
Riverside County Fire Department Office of the Fire Marshal 2300 Market St., Ste. 150, Riverside, CA 92501 Ph. (951) 955-4777 Fax (951) 955-4886 Technical Policy Title: Plant Processing and Extraction
More informationSECTION PLUMBING EQUIPMENT Piping (Plumbing). 2. Division 16 - Electrical Wiring and Connections.
SECTION 15450 PLUMBING EQUIPMENT PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15410 - Piping (Plumbing). 2. Division 16 - Electrical Wiring and Connections. 1.02 SUBMITTALS A. Submit properly identified
More informationDesign and Construction Standards SECTION PLUMBING EQUIPMENT
SECTION 15450 PLUMBING EQUIPMENT PART 1 GENERAL 1.1 SECTION INCLUDES: A. Water heaters. B. Packaged water heating systems. C. Water storage tanks. D. Water softeners. E. Pumps. F. Circulators. 1.2 REFERENCES
More informationANNEX A-1 GEOTHERMAL UNITS INDEX TO SYSTEM/COMPONENT CAUSE CODES BOILER BALANCE OF PLANT STEAM TURBINE GENERATOR MISCELLANEOUS - GEOTHERMAL EXTERNAL
ANNEX A-1 GEOTHERMAL UNITS INDEX TO SYSTEM/COMPONENT CAUSE CODES Boiler Piping System 0500-0620 Condensing System 3110-3199 Circulating Water Systems 3210-3285 Waste Water (zero discharge) 3290-3299 Condensate
More informationDESCRIPTION OF COOLING TOWERS SERIES TAT
DESCRIPTION OF COOLING TOWERS SERIES TAT The TAT series are dedicated to every industrial sector with a modular conception. These models are characterized by SCAM T.P.E. S.r.l. well defined standards and
More informationTechnical Specification For Design and supply of Water Mist cum CAFS (Compressed Air Foam System) Backpack Fire Fighting System
Technical Specification For Design and supply of Water Mist cum CAFS (Compressed Air Foam System) Backpack Fire Fighting System pg. 1 INTRODUCTION : HPCL is in the process of procurement of Water mist
More informationSECTION PLUMBING EQUIPMENT
PART 1 GENERAL 1.1 SECTION INCLUDES A. Water heaters B. Packaged water heating systems C. Water storage tanks D. Water softeners E. Pumps F. Circulators 1.2 REFERENCES SECTION 22 30 00 PLUMBING EQUIPMENT
More informationBrown University Revised August 3, 2012 Facilities Design & Construction Standards SECTION AIR HANDLING UNITS
SECTION 23 70 00 AIR HANDLING UNITS PART 1. GENERAL 1.1 Section includes air-handling units to 15,000 cfm and accessories. 1.2 Related Sections 1 : A. Division 01 - Brown University Standard for Narragansett
More informationSECTION WET PIPE FIRE PROTECTION SPRINKLER SYSTEM
SECTION 213100 WET PIPE FIRE PROTECTION SPRINKLER SYSTEM PART 1 - GENERAL 1.01 GENERAL REQUIREMENTS A. The requirements of the General Conditions and Supplementary Conditions apply to all work herein.
More informationSECTION HEATING BOILERS
SECTION 23 52 00 HEATING BOILERS PART 1 - GENERAL 1.1 SUMMARY A. Section includes boilers, controls and boiler trim, steam and condensate connections, hot water connections, fuel burning system and connections,
More informationRental Boiler Specifications (Nebraska Boiler)
Rental Boiler Specifications (Nebraska Boiler) ESI's 72,000 pph trailer-mounted watertube steam boilers are designed and built in accordance with ASME Code. Each boiler is arranged for natural gas or #2
More informationHHA Bellerive Apartments 7225 Bellerive Houston, Texas J. Allen Management Managing Agent
HHA Bellerive Apartments 7225 Bellerive Houston, Texas 77036 J. Allen Management Managing Agent Scope of Work: 1.) Water Heater Replacement with Vertical Boiler System 2.) Water Conditioning System (Softener)
More informationSECTION COMPRESSED AIR SYSTEM. A. Pipe and pipe fittings, including valves, unions and couplings.
SECTION 15481 COMPRESSED AIR SYSTEM PART 1 - GENERAL 1.1 SECTION INCLUDES A. Pipe and pipe fittings, including valves, unions and couplings. B. Air compressor. C. After cooler. D. Refrigerated air dryer.
More informationCONSIDERATIONS IN CONVERTING A DUAL SHELL OR A DUAL PRESSURE COAL FIRED PLANT CONDENSER INTO A COMBINED CYCLE PLANT CONDENSER
Proceedings of the ASME 2013 Power Conference POWER2013 July 29-August 1, 2013, Boston, Massachusetts, USA POWER2013-98062 CONSIDERATIONS IN CONVERTING A DUAL SHELL OR A DUAL PRESSURE COAL FIRED PLANT
More informationTABLE OF CONTENTS DIVISION 21- FIRE SUPPRESSION PAGES SECTION WATER BASED FIRE PROTECTION SYSTEMS... 5
DOC Cremer Heating and Hot Water Plant Project Number: M 1411-04 TABLE OF CONTENTS DIVISION 21- FIRE SUPPRESSION PAGES SECTION 21 30 00- WATER BASED FIRE PROTECTION SYSTEMS... 5 SECTION 22 40 00 -PLUMBING
More informationCxA to Answer this Section
EXHIBIT 01 91 13-3, SAMPLE Construction checklist items are to be completed as part of initial checkout and subsequent startup, preparatory to Functional testing. This checklist does not take the place
More informationWD7664 / WD7663 Maxon Burner Ellis Whisper Dryer Installation & Start UP
WD7664 / WD7663 Maxon Burner Ellis Whisper Dryer Installation & Start UP Receiving Do a quick visual inspection on the truck for any major damage prior to signing the paperwork. Damage should be noted
More informationTime Extension: Tender submission deadline is extended up to 12:00 Hrs. of
ASSAM ELECTRICITY GRID CORPORATION LIMITED OFFICE OF THE MANAGING DIRECTOR Regd. Office: (FIRST FLOOR), BIJULEE BHAWAN, PALTANBAZAR; GUWAHATI - 781001 CIN: U40101AS2003SGC007238 PHONE: 0361-2739520 FAX
More informationTENDER CRFQ NO (E-TENDER REF NO.13020)
ADDENDUM NO:2 AGAINST TENDER FOR DESIGN, ENGINEERING, SUPPLY, INSTALLATION, TESTING, COMMISSIONING AND POST WARRANTY AMC OF RIM SEAL FIRE PROTECTION SYSTEM FOR BPCL- MUMBAI REFINERY (BPCL MR) TENDER CRFQ
More informationBharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli , TAMIL NADU, INDIA MATERIALS MANAGEMENT / CAPITAL EQUIPMENT
An ISO 9001 Company Bharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli 620014, TAMIL NADU, INDIA MATERIALS MANAGEMENT / CAPITAL EQUIPMENT ENQUIRY Phone: +91 431 257 70 49 Fax
More informationDesign and Specification of Air-Cooled Steam Condensers
Design and Specification of Air-Cooled Steam Condensers M.W. Larinoff, W.E. Moles and R. Reichhelm Hudson Products Corporation Even the nonspecialist purchaser of an air-cooled steam condenser can apply
More informationC. All components of the systems described shall meet the requirements as stated herein and shall be approved by the Architect and Consultant.
SECTION 218800 - FIRE PROTECTION 1. GENERAL A. Provisions of Division 1, GENERAL REQUIREMENTS, and Section 230000, MECHANICAL GENERAL CONDITIONS, and Section 230050, SEISMIC PROTECTION are a part of this
More informationSTEAM AND CONDENSATE PIPING AND PUMPS DESIGN AND CONSTRUCTION STANDARD
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
More informationInstallation, Operation and Maintenance Instructions for Thermax Semi-Storage Calorifier
OM001 Installation, Operation and Maintenance Instructions for Thermax Semi-Storage Calorifier These operating and maintenance instructions are for standard semi-storage calorifiers (vessels fitted with
More informationSECTION HEATING BOILER FEEDWATER EQUIPMENT
SECTION 23 53 00 HEATING BOILER FEEDWATER EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section includes boiler feedwater pumps, de-aerators, accessories, controls and tanks. 1.2 REFERENCES A. ASME (American
More informationDESIGN & CONSTRUCTION GUIDELINES
ADMINISTRATIVE SERVICES 4202 E. FOWLER AVENUE, FPC110 PHONE: (813) 974-2625 FACILITIES PLANNING & CONSTRUCTION TAMPA, FLORIDA 33620-7550 WEBSITE: USF.EDU/FPC DESIGN & CONSTRUCTION GUIDELINES DIVISION 21
More informationAPPENDIX 3J FOOD SERVICES SPECIFICATIONS
APPENDIX 3J FOOD SERVICES SPECIFICATIONS 1. FOOD SERVICES 1.1 Design Consultant Project Co will retain as part of its professional design team a qualified food service consultant that is a professional
More informationExclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA
Page 236423-1 Copyright 2009 by The American Institute of Architects (AIA) Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA Modified by MSU Physical Plant
More informationCNS CENTRIFUGAL MULTISTAGE WATER DESCALING PUMPS BB4 TYPE API 610 ENGINEERING FLOW SOLUTIONS
CNS CENTRIFUGAL MULTISTAGE WATER DESCALING PUMPS BB4 TYPE API 610 ENGINEERING FLOW SOLUTIONS CNS Pumps For Water Descaling Description The CNS series pumps are centrifugal, multistage, horizontal, with
More informationCL44eR DISHWASHER STANDARD FEATURES MODEL OPTIONS AT EXTRA COST ACCESSORIES DIRECTION OF OPERATION VOLTAGE. Item # Quantity C.S.I.
Item # Quantity C.S.I. Section 11400 DISHWASHER STANDARD FEATURES Energy recovery 202 racks per hour Opti-RinSe system 30 KW electric booster heater Rapid return conveyor drive mechanism Insulated hinged
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 22 40 00 - PLUMBING FIXTURES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Faucets for lavatories, bathtubs, bathtub/showers, showers and sinks. 2. Flushometers. 3. Toilet
More informationBASIL 6700 TUNNEL CAGE WASHER
BASIL 6700 TUNNEL CAGE WASHER APPLICATION For thorough, efficient cleaning of cages, debris pans, bottles, feeder bowls and miscellaneous items used in the care of laboratory animals. DESCRIPTION The Basil
More informationSECTION STEAM CONDENSATE PUMPS
SECTION 23 22 23 STEAM CONDENSATE PUMPS PART 1 - GENERAL 1.1 DESCRIPTION SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable in the
More informationPackaged Semi-Instantaneous Steam Fired Water Heater
MODEL STX Packaged Semi-Instantaneous Steam Fired Water Heater Shell and Tube Style Heater Features Reliable Only high grade materials used in construction to ensure long operating life Heat exchange pressure
More informationPIP PCTPA001 Testing of Process Analyzer Systems
January 2016 Process Control PIP PCTPA001 Testing of Process Analyzer Systems PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities, this Practice
More informationHow to improve air cooler vacuum steam condensers performance in the field
How to improve air cooler vacuum steam condensers performance in the field By Marc Ellmer ELFLOW BV The Netherlands Introduction Air cooled vacuum steam condensers (ACC s) are used to condense exhaust
More informationVS SERIES NH3 STEAM VAPORIZERS OPERATION MANUAL
VS SERIES NH3 STEAM VAPORIZERS Revised March 1997 OPERATION MANUAL CONTENTS PAGE 1. GENERAL................................... 1 Figure 1-1 - VS Series Vaporizer......................... B How to Select
More informationClearFire Economizer Model ECF Integral or External. Addendum to manuals CFH and CFV
ClearFire Economizer Model ECF Integral or External Addendum to manuals 750-295 CFH and 750-269 CFV CB-8466 08/2011 1-GENERAL The Model ECF economizer is a stainless steel coil tube arrangement using
More informationCOOLING TECHNOLOGY INSTITUTE
PAPER NO: TP09-02 CATEGORY: REPAIR AND CONSTRUCTION COOLING TECHNOLOGY INSTITUTE COMMON INDUSTRIAL COOLING TOWER ERRORS AND OMISSIONS JAMES L. WILLA WILLA, INC. The studies and conclusions reported in
More informationSECTION AUTOMATIC SPRINKLER PIPING
SECTION 15330 AUTOMATIC SPRINKLER PIPING ****** ***** **** *** ** * ** *** **** ***** ****** NOTE TO SPECIFIER: This section contains several types of automatic sprinkler piping. Some piping is allowed
More information