LOCAL EXTRACTION Pure advantages. The ideal extractor for light industry and laboratory environments.

Transcription

1 The ideal extractor for light industry and laboratory environments. With its optimal design, the mm FUMEX ME has a very low pressure drop, which provides many valuable benefits. - Low pressure drop saves energy. - Air flow noise is reduced. - Lower pressure drop is achieved without selecting a larger diameter extractor. - Lower pressure drop allows the ME to be combined with additional extraction systems. To further facilitate maneuvering of the extractor, the models 1650 and 1900 are equipped with a pulling gas spring as standard and the models 2100 and 2650 with two pulling gas springs. An easy-to-grip handle facilitates the maneuverability of the extractor. Unique design and stable mounting brackets make the Fumex ME your best choise. Support for designing an effective system can be found on page 5, and at where you will find our design tool and CAD drawings. The Fumex range also includes fans, accessories, automatic control and filters suitable for local extraction. LOCAL EXTRACTION Pure advantages

2 Always choose a low pressure drop Lowest possible pressure drop is a quality aspect that always should be considered. With its uniquely designed joint construction, Fumex ME combines maximum flexibility with low pressure drop. The air passes through the joints without creating unnecessary turbulence, thus producing an energy-saving low pressure drop and a quieter working environment. Recommended air flow The recommended air flow for a Ø100 arm is m³/h, See table and diagram. Activity Air flow Laboratories m 3 /h l/s Light industry 300 m 3 /h 80 l/s Static pressure drop (Pa) Air flow (m 3 /h) Static pressure drop is measured in accordance with ISO standard Optimal capture For optimum benefit from the local extractor, it is important to use the flexibility of the extractor to get as close to the contaminant as possible. A good rule of thumb would be a distance of 2 3 times the diameter of the extractor tube. At the recommended air flow, the extractor will provide high efficiency even if disturbances are generated in the surroundings mm Unique benefits The Fumex ME s joints have a patented friction design that, combined with the large joint diameter and single grip handle, provide a secure, position-stable arm with smooth adjustments. All without the need to apply excessive force or use tools on the adjusting knob. Joints with reinforced ends and ball bearings moderate the friction and allow the arm to be moved up and down while maintaining stability and function. Handle for easy adjustment A steady and easily accessible handle, that provides easy adjustment, is fitted as a standard on all models of Fumex ME Ø100 mm.

3 One arm. All options. Fumex ME has a complete range of accessories to suit every situation, enabling you to create the optimal extractor for the evacuation of hazardous airborne gases and particulates. PP version Used primarily for evacuating very corrosive contaminants in high concentrations, e.g. in certain laboratories and in the pharmaceutical and chemical industries. Standard version Suitable for evacuating most types of airborne contaminants, e.g. in laboratories, schools, hospitals, the pharmaceutical industry, nail salons and light industrial applications. ATEX version Suitable for evacuating airborne contaminants where there is a requirement for an ATEXclassified environment, e.g. in laboratories, the chemical and petrochemical industries, gas distribution, and the paint and pharmaceutical industries.

4 MET for ceiling and wall mounting, 3 joints Standard Size (mm) Gas spring Weight MET ,9 MET ,4 MET ,9 MET ,4 MET ,9 MET B MET ,4 A PP Size(mm) Gas spring Weight MET PP ,9 MET PP ,4 MET PP ,9 MET PP ,4 MET PP ,9 MET PP ,4 MET for ceiling or wall mounting, excluding bracket MTI or MVK-125. ATEX Size (mm) Gas spring Weight MET EX ,9 MET EX ,4 MET EX ,9 MET EX ,4 MET EX ,9 MET EX ,4 Pressure drop dB(A) Static pressure drop (Pa) Air flow (m 3 /h) Static pressure drop is measured in accordance with ISO standard Noise level is measured in accordance with ISO standard Indicated sound level refers to sound pressure level.

5 MEB for table mounting, 3 joints Standard Size (mm) Gas spring Weight MEB ,9 MEB B MEB ,4 A MEB ,9 MEB ,4 PP Size (mm) Gas spring Weight MEB PP ,9 MEB PP ,4 MEB PP ,9 260 MEB PP ,4 ATEX Size (mm) Gas spring Weight MEB EX ,9 MEB EX , Ø 6 (4X) 119 MEB EX ,9 MEB EX ,4 Reach at recommended installation height The following installation heights and sideways displacement relative to the work area are recommended for optimal extraction: Recommended installation height Designation H (mm) MET MET MET MET MET MET MET 2650 MET 2100 MET 1900 MET 1650 MET 1350 MET 1150 MET 2650 MET 2100 MET 1900 MET 1650 MET 1350 MET S H Recommended side displacement radius, relative to work area 900 Designation S (mm) MET MET MET MET MET MET MET2650 MET2100 MET1900 MET1650 MET1350 MET1150 Working radius Maximum radius

6 Hoods Ø 250 METAL HOOD The metal hood is used when working in corrosive environments and for capturing hot gasses and dust splatter. Metal hoods can be fitted with work lighting. MEM PP, EX 510 Standard/PP: EX Powder-coated aluminium Powder-coated aluminium Ø 350 DOME HOOD The clear dome hood is suitable for lighter gasses with a wider dispersal of contaminants without blocking the user s vision. MEK PP,EX 610 Standard: PP EX PMMA Polypropylene, transparent PEEL black Ø 500 DOME HOOD The clear dome hood is suitable for lighter gasses with a wider dispersal of contaminants without blocking the user s vision. MEK PP,EX 735 Standard: PP EX PMMA Polypropylene, opaque PEEL black SQUARE HOOD The square hood is suitable for placing above gases with a high lift, or adjacent to the work surface for contaminants with no lift or low lift all this without interfering with the work. MESH Standard: PETG ,5 200 FLAT SCREEN HOOD The flat screen hood is designed to maximise the working area without obscuring the object from the user. The flat screen hood gives the best suction effect for table and bench tasks. Temp. range: -15 C to +80 C MEPH PP,ES, EX 625 Standard: PP EX PETG Polypropylene PEEL black PROTECTIVE GRILL Protective grill to be monted in joints. Prevents objects being sucked into the system. MESG-100 EX 12 Standard, EX: EN

7 Brackets All Fumex laboratory extractors have as standard a full swivel that allows 360 of rotation without the need to add special sleeve couplings. Both ceiling and wall brackets have a special squareshaped profile in anodised aluminium to provide a stylish and stable installation. This aluminum profile also allows both the wall and ceiling brackets to be custom tailored at the job site. MTI MTI CT The MTI ceiling bracket The ceiling bracket functions as a simple and stable duct for outgoing air, avoiding the need for expensive ducting and additional holes through false ceilings. On request, the MTI can be supplied in lengths exceeding 2 m. Dimensions Weight (mm) Standard L (kg) MTI ,90 MTI ,80 MTI ,75 MTI ,65 MTI ,60 MTI ,50 MTI ,40 Static pressure drop (Pa) Air flow (L/s) MTI Air flow (m 3 /h) Ø10(x4) L Ø The MTF ceiling bracket Ceiling bracket, for fitting through beams. The attachment plate is adjustable for the entire length of the aluminium profile. If required, the aluminium profile can be cut during fitting. Ø10 (x4) Ø125 Dimensions Weight (mm) Standard L (kg) MTF ,50 As well as the standard design, the MTI/MTF is available in an ATEX (EX) version. 5 The ceiling brackets can be supplied with an epoxy-coated exterior in all lengths up to 3 m (L). For aggressive environments, we recommend epoxy coating on the interior and exterior up to 1.25 m (IL) The MTI CT escutcheon plate Escutcheon plate, used with the MTI ceiling brackets for stabilization and to cover ducting in false ceilings. Weight Standard (kg) MTI CT-125 0, As well as the standard design, the escutcheon plate is available in an ATEX (EX) version. Ø 10 (4X) 3 MVK wall bracket Wall brackets can be special ordered in custom horizontal and vertical lengths. Weight Standard (kg) MVK-125 2, Ø 10 (4X) 232 Ø As well as the standard design, the bracket is available in an ATEX (EX) version.

8 description Friction joints Ball bearing-equipped adjustable friction joints in polypropylene (PP), with guide ring in low friction-treated rubber. Support springs and other component parts in zinc-plated steel or stainless steel. Tubes Made from thin-walled anodised aluminium or from polypropylene. Air-tight damper supplied as standard. ME Standard The standard ME version has polypropylene joints and anodised aluminium tubes. The standard ME version is suitable for evacuating most types of airborne contaminants, e.g. in laboratories, schools, hospitals, the pharmaceutical industry, hairdressing salons and light industrial applications. Delivery Ceiling- Supplied assembled, excluding hood. The MTI or MET MTF ceiling brackets should be ordered separately. Wall- MET Table- MEB Supplied assembled, excluding hood or suction nozzle. MVK-125 wall bracket should be ordered separately. Supplied assembled, with attachment plate for table fitting, excluding hood. The MBF flexible table bracket should be ordered separately. ME PP Polypropylene joints and tube version. All metallic parts that are in contact with the air flow are made of stainless steel. The PP version of the ME is used primarily for evacuating very corrosive contaminants in high concentrations, e.g. in certain laboratories and in the pharmaceutical and chemical industries. When using a PP extractor fitted to a ceiling, we recommend that you order the MTI ceiling bracket with an internal epoxy coating. ME ATEX Conductive polypropylene joints and tubes. All metallic parts that are in contact with the air flow are made of stainless steel. Static electricity is diverted to a separate earth connection. All steel supporting parts are lined in a conductive powder coating. The product meets the requirements of category 2 of the ATEX directive (94/9/EC) for gases and dust. The ATEX version of the ME is suitable for evacuating airborne contaminants where there is a requirement for ATEX-classified products, e.g. laboratories, the chemical and petrochemical industries, gas distribution, and the paint and pharmaceutical industries. Verkstadsvägen 2, Skelleftea, Sweden Tel : , Fax: info@fumex.se