Data Sheet. Compact Mixing Shunt for Floor Heating, FHM-Cx. Application:

Transcription

1 Data Sheet Compact Mixing Shunt for Floor Heating, FHM-Cx Application: FHM-C1 Mixing shunt FHM-C/ FHM-C Mixing shunt FHM-C Mixing shunt FHM-C The Danfoss floor heating compact mixing shunts are used for regulating the correct flow and supply temperature in hydronic floor heating systems. The compact design and flexibility allows mounting the mixing shunt directly to the manifold, both on left and right side and primary pipe connection to the shunt from the side or below. A self-acting proportional regulator is used to regulate the supply temperature. The regulator ensures the correct mix so that the desired supply temperature to the underfloor heating system always remains constant. A safety thermostat (standard in models FHM-C1 and FHM-C) protects the floor against too high temperatures. The energy-saving electronic variable speed pump (Grundfos Alpha+) adjusting itself for correct flow in the circuits; versions with a standard -speed pump (Grundfos UPS) are also available. Versions with different capacities are available. The built-in check valve ensures correct flow direction and the mixing shunt is prepared for inserting temperature sensors. An air-vent on top and a thermometer completes the mixing shunt. The Danfoss floor heating compact mixing shunt can be mounted directly to the Danfoss manifold system without using special equipment. By using Danfoss floor heating controls all expectations of a professional floor heating system are fullfilled. VD.UL.F1.0 Produced by Danfoss Floor Heating Hydronics 09.00

2 Data Sheet Technical Data: Product Type FHM-C1 FHM-C FHM-C FHM-C* FHM-C Code no. 088U U U U U008 max effect in kw at secondary Δt=K max effect in kw at secondary Δt=10K 7 7,, Primary connection ½ ½ ½ ½ ½ Supply voltage 0V AC 0V AC 0V AC 0V AC 0V AC Pump type, Grundfos Alpha+ 1-0 CIL ² Alpha+ 1-0 CIL ² Alpha+ 1-0 CIL ² UPS 1-0 CIL ² UPS 1-0 CIL ² Flow limiter FHM-FL Standard As accessory As accessory As accessory As accessory Measurement set for needles ³ FHM-MS Flow temp. control FH-TC, 18- C Electric safety thermostat FH-ST¹ Supply flow thermometer 0-0 C FHD-T Standard As accessory As accessory As accessory As accessory X X X X X X as accessory as accessory X as accessory X X X X X Integrated check valve X X X X X ¹ safety thermostat with prewired plug 0V (length 1m) and wire for ie. pump connection or together with CF, switch off temp. C, ±K ² CIL = bottom part of composite material, PN10 ³ Can only be used by new installation of shunt and manifold Max effect at Δt=0K in primary(70/0) and Δt=K (10K) in secondary line with heatloss 0W/m² * prewired to pump, stops by reaching the safety temperature of C Body,unions, other metal parts O-rings, seals Check valve Weight (depending on model) Max. differential pressure Max. working pressure Brass / stainless steel EPDM POM/ stainless steel ca. kg 0, bar PN10 Max. flow temperature 90 C Spare parts Thermometer 0-0 C, Ømm, FHD-T FH-TC 1-0 C temperature controller Safety thermostat FH-ST Flow limiter, FHM-FL Measuring set, FHM-MS Angle fittings, FHM-AF, Set á Stk. Code number 088U U00 088U U00 088U00 088U00 VD.UL.F1.0 Produced by Danfoss Floor Heating Hydronics 09.00

3 Data Sheet FH-ST Thermostat Electrical Connection: 0V / 1A T S C The FH-ST safety thermostat is fixed on the tube and protects the floor and the system against too high temperatures, especially when wooden floor is used. The electrical installation has to be done by authorized people only (0V DC). The FH-TC -thermostat switches off the power supply of the floor heating base unit when the temperature reaches the shut off temperature of C. By switching off the power supply of the underfloor heating base unit the actuators (NC) will close automatically and the floor heating system is protected. The thermostat can also be connected to a pump or zone valve. Technical Data: Code number for FH-ST 088U001 Shut off temperature C Switch difference Classification K IP 0 (mounted) FH-TC FH-TC is used for flow temperature control of floor heating and radiator heating systems. FH-TC is a self-acting thermostatic sensor The water temperature is directly measured by a stainless steel immersion sensor. Features: - Closes on rising sensor temperature; - Closes against differential pressure of up to bar. - Temperature range: 18- C - Designed for pressure PN (max) 0 C C 0 C C 0 C C 0 C VD.UL.F1.0 Produced by Danfoss Floor Heating Hydronics 09.00

4 1 Data Sheet FHM-MS Danfoss IN PFM 000 OUT 1 kv s 7, FHM-FL L/h The flow running through the FHM-MS (fixed orifice) can be measured by using the Danfoss measuring equipment PFM 000 or other brands of measuring equipment. The FHM-MS valve is supplied with two measuring nipples for mm needles. The measuring nipples are placed across a fixed orifice and the differential pressure can be measured across this orifice. Fixed orifice (kvs 7,) and differential pressure will be used in the measuring equipment to define the flow. Measuring on a fixed orifice valve is very fast and easy VD.UL.F1.0 Produced by Danfoss Floor Heating Hydronics 09.00

5 Data Sheet System: FHM-C Combined Floor Heating System with Boiler. FHM-C Combined Floor Heating System with Heat Pump. VD.UL.F1.0 Produced by Danfoss Floor Heating Hydronics 09.00

6 1 Data Sheet Dimensions: 9 10 Danfoss 1 1 OUT FHM-C1 9 7 Danfoss 1 1 OUT FHM-C, FHM-C VD.UL.F1.0 Produced by Danfoss Floor Heating Hydronics 09.00

7 Data Sheet 7 7 Danfoss 1 1 OUT FHM-C, FHM-C VD.UL.F1.0 Produced by Danfoss Floor Heating Hydronics

8 Data Sheet VD.UL.F1.0 Produced by Danfoss Floor Heating Hydronics 09.00