R586R. Distribution and Regulation units. Datasheet 0861EN 04/2019 R586RY103 R586RY102 R586RY101 R586RY104

Transcription

1 R8R Distribution and Regulation units Datasheet 08EN 0/09 R8RY0 R8RY0 R8RY0 R8RY0 Unit with insulation and actuator (optional) R8RY R8RY R8RY R8RY R8R distribution units control heating and cooling for one zone of the system (R8RY0- for heating only). he R8RY versions include a low-energy consumption circulator complying with directive ErP 009//CE, interception ball s with integrated thermometer, check integrated in the return circuit and polypropylene foam rigid insulation (EPP). he R8RY are equipped with a mixing ; the actuator to control the mixing (when included) is sold separately. he mixing actuators and the delivery temperature can be controlled with KLIMAbus thermoregulation products. VIDEO Frame the QR code with your smartphone or tablet to view the video tutorial.

2 Versions and product codes PRODUC CODE APPLICAION DELIVERY/REURN OUPUS REVERSIBILIY CIRCULAOR MIXING VALVE MIXING ACUAOR (OPIONAL) R8RY0 Heating/Cooling Yes Wilo Para /7 - R8RY0 Heating/Cooling Yes Wilo Para /7 Ball mixing (R9) K7Y00/0/0 R8RY0 Heating/Cooling No Wilo Para /7 Sector mixing (R97) K7Y00/0/0 R8RY0 Heating only Yes Wilo Para /7 hermostatic mixing - R8RY Heating/Cooling Yes Not included - R8RY Heating/Cooling Yes Not included Ball mixing (R9) K7Y00/0/0 R8RY Heating/Cooling No Not included Sector mixing (R97) K7Y00/0/0 R8RY Heating only Yes Not included hermostatic mixing - Optional components K7Y00: actuator with integrated constant temperature regulator K7Y0: -point floating actuator controllable with KLIMAbus thermoregulation K7Y0: actuator with V regulation controllable with KLIMAbus thermoregulation R8Y0: differential by-pass kit RY00: interception ball F x nut / F, for installation upstream the distribution unit KLIMAbus thermoregulation: KLIMAbus thermoregulation components (regulation unit, thermostats, ambient probes, etc...) Compatible circulators (for circulator-free units) Wilo Para - 80 mm centre distance Grundfos Alpha series - interassse 80 mm General technical data Fluids: water, glycol-based solutions (max. 0 %) emperature range: 00 C ( 9 C for R8RY0-) Max. working pressure: bar or 0 bar depending on versions Connections: system side: F ISO 8 boiler side: / M ISO 8 outputs centre distance: mm Circulator Wilo Para /, 80 mm centre distance, complying with directive ErP 009//CE (for versions with circulator) Galvanized steel spacer, 80 mm centre distance (for circulator-free versions) Interception ball s with thermometers (scale 0 0 C) and connections for by-pass kit Check integrated on return circuit EPP insulation, density kg/m Wall-mount plate (screw anchors not included) NOE. Specific data referring to single R8R units are given in the following corresponding paragraph. Materials Interception ball s: CW7N brass body, PFE sealings, plastic handle Spacer with check : CW7N brass body, POM check Polypropylene foam insulation (EPP) Gaskets: EPDM

3 Components F F F F F F F F 7 BACK VIEW / M / M / M / M / M / M / M / M COMPONEN REFERENCE R8RY0 R8RY R8RY0 R8RY R8RY0 R8RY R8RY0 R8RY Brass fitting R9 mixing ball R97 mixing sector Mixing thermostatic Circulator Galvanized steel spacer Circulator Galvanized steel spacer Circulator Galvanized steel spacer Circulator Galvanized steel spacer Delivery ball, with thermometer and connections for by-pass kit Delivery ball, with thermometer and connections for by-pass kit Delivery ball, with thermometer and connections for by-pass kit Delivery ball, with thermometer and connections for by-pass kit Spacer with integrated check Spacer with integrated check Spacer with integrated check Spacer with integrated check Return ball, with thermometer and connections for by-pass kit Return ball, with thermometer and connections for by-pass kit Return ball, with thermometer and connections for by-pass kit Return ball, with thermometer and connections for by-pass kit Insulation shell Insulation shell Insulation shell Insulation shell 7 Wall-mount plate Wall-mount plate Wall-mount plate Wall-mount plate

4 Main features Delivery/return outputs reversibility R8RY units include reversible delivery and return outputs. R8RY0- units instead are not reversible. R8RY0- R8RY0- R8RY0- Invert delivery and return by fitting the outputs in the insulation slots. Invert delivery and return by fitting the outputs in the insulation slots. Also invert the cap and the copper fitting Invert delivery and return by fitting the outputs in the insulation slots and turn the mixing upside down. Check integrated on return output All R8R units include a check inside the brass spacer top, on the return output. he check can be disassembled by removing the Seeger ring used to fit it to the spacer. Installation of RY00 ball s R8R units can be intercepted by installing the RY00 ball s upstream. he ball s can be opened and closed using a mm Allen wrench. Check RY00 Installation of R8Y0 differential by-pass kit he differential by-pass kit protects the circulator enabling water recirculation inside the R8R unit when the secondary system is off or completely closed. he kit includes a brass spacer with integrated check calibrated at a fix value of mho, two nuts to be screwed on the interception s and two PFE gaskets. R8Y0 Gasket Check Nut

5 R8RY0 - R8RY Operation R8RY0 and R8RY distribution units without mixing are used in heating and cooling systems such as relaunching units for direct outputs of high/low temperature combined systems. he units include interception s with thermometer both on the delivery and return circuit and a check on the return spacer. he two delivery and return outputs are reversible and a R8Y0 differential by-pass kit can be installed in between (see paragraph Main characteristics ). b a a b Boiler room side System side Circulator (per R8RY0) or galvanized steel spacer (per R8RY) Check Interception ball with thermometer and by-pass kit connections Differential by-pass kit (optional) Specific technical data emperature range: 00 C Max. working pressure: 0 bar Connections: system side: F ISO 8 boiler side: / M ISO 8 outputs centre distance: mm Weight:,8 kg (with circulator);,0 kg (without circulator) Materials Interception ball s: CW7N brass body, PFE sealings, plastic handle Spacer with check : CW7N brass body, POM check Polypropylene foam insulation (EPP) Gaskets: EPDM Flow rate/power/hydraulic head diagram Hydraulic head [mh O] R8RY ,,, Flow rate [m /h] 0 t 0 Power [kw] 0 0 t 0 t 0 0 t 0 NOE. For proper interpretation of the diagram, see example on page. NOE. Curves obtained with circulator set to constant speed, level III mode.

6 R8RY0 - R8RY Operation R8RY0 and R8RY distribution units with R9 mixing ball can be used in heating and cooling systems to control the system delivery temperature. Operation is possible only when combined to an actuator and possibly a KLIMAbus thermoregulation system. he units include an interception with thermometer on both delivery and return circuits and a check on the return spacer. he two delivery and return outputs are reversible and a R8Y0 differential by-pass kit can be installed in between (see paragraph Main characteristics ). b a b Boiler room side System side Circulator (per R8RY0) or galvanized steel spacer (per R8RY) Specific technical data emperature range: 00 C Max. working pressure: 0 bar Connections: system side: F ISO 8 boiler side: / M ISO 8 outputs centre distance: mm Weight:,8 kg (with circulator);,0 kg (without circulator) Materials Interception ball s: CW7N brass body, PFE sealings, plastic handle Mixing : brass body, plastic handle, hard drawn copper pipe connecting delivery and return circuits, EPDM gaskets Spacer with check : CW7N brass body, POM check Polypropylene foam insulation (EPP) Gaskets: EPDM Flow rate/power/hydraulic head diagram 9 a B AB A M M Check Interception ball with thermometer and by-pass kit connections Differential by-pass kit (optional) Mixing with actuator Hydraulic head [mh O] 8 7 R8RY ,,, Flow rate [m /h] 0 t 0 NOE. For proper interpretation of the diagram, see example on page. NOE. Curves obtained with circulator set to constant speed, level III mode. Power [kw] t 0 t t 0 Kv R9 mixing Manual handle position 0 (B AB) (A AB) Kv (AB),0,8 7,8 9,8, 8,9

7 Actuator installation K7Y00 or K7Y0/0 actuators can be installed on R9 mixing s. Before closing the R8R unit with the front insulation shell, with a sharp-edge cutter carve out the shape of the K7 actuator (to make this operation easier, the shape of the actuator is reproduced on the back of the front insulation shell). Actuator installation K7Y0/0 on R9 mixing Use the Connection kit 09 included in the actuator package. Before installing the K7Y0/0 actuator on the R9 mixing, make sure the is in by-pass position (milling in OFF position) and the actuator is in closing position. For the K7Y0 actuator: With the body on the left and the by-pass -shaped fitting on the right, the DIP must be positioned on OFF (a). With the body on the right and the by-pass -shaped fitting on the left, the DIP must be positioned on ON (b). Connection kit GIACOMINI CODE: 09 a ON OFF K7Y0 b ON OFF K7Y0 K7Y0 Black: opening Blue: neutral Brown: closing K7Y0 Black: closing Blue: neutral Brown: opening 7

8 Actuator installation K7Y00 on R9 mixing Use the Connection kit 09 included in the actuator package. Before installing the K7Y00 actuator on the R9 mixing, make sure the is in by-pass position (milling in OFF position) and the actuator is in closing position. With the body on the left and the by-pass -shaped fitting on the right, the DIP must be positioned on OFF (a). With the body on the right and the by-pass -shaped fitting on the left, the DIP SYSEM must be positioned on ON (b). Connection kit GIACOMINI CODE: 09 a b ON OFF ON OFF NOE. When the DIP position is changed, actuator calibration begins. he LED blinks (x/sec) and the actuator is turned right and left. When this happens, leave the actuator in the AUO position, do not change the settings and do not cut off electric power. When calibrating the actuator, to protect the system, the circulator must be turned off to prevent temperature fluctuations in the system. Installation of temperature probes he temperature probe must be installed after the system circulator, at a max. distance of, m from the actuator. For contact installation, use the kit included with the actuator. his requires a flat surface with a min. length of 0 mm to position the probe. For immersion installation, the probe must be installed in a housing up to half of the piping diameter (the R7Y00 housing can be used by installing it in the ball sockets included with the R8R unit). his requires a suitable mechanic protection of the probe and probe wire. he wire must be insulated in case of contact with very hot parts. 8

9 R8RY0 - R8RY Operation R8RY0 and R8RY distribution units with R97 mixing sector can be used in heating and cooling systems to control the system delivery temperature. Operation is possible only when combined to an actuator and possibly a KLIMAbus thermoregulation system. he units include an interception with thermometer on both delivery and return circuits and a check on the return spacer. he mixing is also equipped with a manually adjustable by-pass to insert the function of fixed recirculation of the system. he two delivery and return outputs are NO reversible (see Main Characteristics paragraph) and a R8Y0 differential by-pass kit can be installed in between (see paragraph Main characteristics ). b a b Boiler room side System side Circulator (per R8RY0) or galvanized steel spacer (per R8RY) Check Specific technical data emperature range: 00 C Max. working pressure: 0 bar Connections: system side: F ISO 8 boiler side: / M ISO 8 outputs centre distance: mm Weight:,7 kg (with circulator);,9 kg (without circulator) Materials Interception ball s: CW7N brass body, PFE sealings, plastic handle Valvola miscelatrice: corpo in ottone, tubo di raccordo in ottone, Gaskets in EPDM, FPM e PFE. Spacer with check : CW7N brass body, POM check Polypropylene foam insulation (EPP) Gaskets: EPDM Flow rate/power/hydraulic head diagram Hydraulic head [mh O] R8RY0 a B AB A M M Interception ball with thermometer and by-pass kit connections Differential by-pass kit (optional) Mixing with actuator Mixing recirculation by-pass Power [kw] 0 0 0,,, Flow rate [m /h] 0 t t 0 t 0 t 0 NOE. For proper interpretation of the diagram, see example on page. NOE. Curves obtained with circulator set to constant speed, level III mode. 9

10 R97 mixing Kv Equal percentage : to absolute value variations of the stroke always corresponds the same % variation of the outflow coefficient (example: if the opens by 0 %, the Kv will vary by 0 %), notwithstanding the position of the recirculation by-pass. Operation of mixing recirculation by-pass R97 mixing s include a by-pass which activates a fix recirculation on the mixing (B AB). AB AB S S 0 B B Kv [m /h] 8 B AB A BY-PASS OFF A BY-PASS ON WARNING. Do not loosen the safety device (S) next to the by-pass adjustment screw. High pressures may violently eject it from its seat. A Opening stroke [%] Actuator installation K7Y00 or K7Y0 actuators can be installed on R97 mixing s. Before closing the R8R unit with the front insulation shell, with a sharp-edge cutter carve out the shape of the K7 actuator (to make this operation easier, the shape of the actuator is reproduced on the back of the front insulation shell). Actuator installation K7Y0/0 on R97 mixing Use the Connection kit 097 included in the actuator package. Before installing the K7Y0/0 actuator on the R97 mixing, make sure the is in by-pass position ( A notch downwards), the actuator is in closing position, put the indicator in position for a clockwise rotation and the DIP is in ON position for K7Y0. Connection kit ROOMIX CODE: 097 ON OFF K7Y0 K7Y0 BY-PASS A Black: closing Blue: neutral Brown: opening 0

11 Actuator installation K7Y00 on R97 mixing Use the Connection kit 097 included in the R8R package. Before installing the K7Y00 actuator on the R97 mixing, make sure the is in by-pass position ( A notch downwards), the actuator is in closing position and the DIP is in ON position. Connection kit ROOMIX CODE: 097 ON OFF BY-PASS A NOE. When the DIP position is changed, actuator calibration begins. he LED blinks (x/sec) and the actuator is turned right and left. When this happens, leave the actuator in the AUO position, do not change the settings and do not cut off electric power. When calibrating the actuator, to protect the system, the circulator must be turned off to prevent temperature fluctuations in the system. Installation of temperature probes he temperature probe must be installed after the system circulator at a max. distance of, m from the actuator. For contact installation use the kit included with the actuator. his requires a flat surface with a min. length of 0 mm to position the probe. For immersion installation, the probe must be installed in a housing up to half of the piping diameter (the R7Y00 housing can be used by installing it in the ball sockets included with the R8R unit). his requires a suitable mechanic protection of the probe and probe wire. he wire must be insulated in case of contact with very hot parts.

12 R8RY0 - R8RY Operation R8RY0 and R8RY distribution units with mixing thermostatic can be used in heating-only systems to control the system delivery temperature and maintain it at the desired constant temperature. he setting range of the mixing thermostatic allows for applications on low-temperature radiant systems and/ or fan-coil applications. he units include interception s with thermometer on both delivery and return circuits and a check on the return spacer. he two delivery and return outputs are reversible and the R8Y0 differential by-pass kit can be installed in between (see paragraph Main characteristics ). b a b Boiler room side System side Specific technical data emperature range: 9 C Max. working pressure: bar Connections: system side: F ISO 8 boiler side: / M ISO 8 outputs centre distance: mm Weight: 7,0 kg (with circulator);, kg (without circulator) Materials Interception ball s: CW7N brass body, PFE sealings, plastic handle Valvola miscelatrice: corpo in ottone, otturatore in PSU GF0, molla in acciaio inox, Gaskets in EPDM, sensore a cera. Spacer with check : CW7N brass body, POM check Polypropylene foam insulation (EPP) Gaskets: EPDM Flow rate/power/hydraulic head diagram Circulator (per R8RY0) or galvanized steel spacer (per R8RY) Check Interception ball with thermometer and by-pass kit connections Hydraulic head [mh O] R8RY0 a Differential by-pass kit (optional) 0 0 0,,, Flow rate [m /h] 0 t hermostatic mixing 0 Power [kw] 0 0 t 0 t 0 0 t 0 NOE. For proper interpretation of the diagram, see example on page. NOE. Curves obtained with circulator set to constant speed, level III mode.

13 hermostatic mixing Before closing the R8R unit with the front insulation shell, with a sharp-edge cutter carve the side to adjust the position of the mixing thermostatic handwheel (to make this operation easier, the shape of the handwheel is reproduced on the side of the front insulation shell). Kv:, Sensitivity: ± C Handwheel position Min. Max. emperature [ C] Dimensions B B Ø0 L E F Ø0 G I H A C D A PRODUC CODE A x B C [mm] D [mm] E [mm] F [mm] G [mm] H [mm] I [mm] L [mm] R8RY0 R8RY0 R8RY0 R8RY0 R8RY / M x F R8RY R8RY R8RY

14 Example of application diagram Application diagram for heating-only system with R8SEP complete of R8RY0 for high-temperature radiator zone + R8RY0/0 for low-temperature radiant system zone and mixing actuator controlled by KLIMAbus thermoregulation..a. KLIMAbus.A. R8R R8SEP

15 Interpretation of flow rate/power/hydraulic head diagram With the system Power and Δt project data known, trace a horizontal line starting from the Power axis up to intersecting the required Δt (A). From the obtained intersection point, trace a vertical line up to intercepting the operational curve of the R8R unit (B), this will show the operational flow rate and hydraulic head available downstream the R8R unit (B, C). Example: Power = 0 kw Δt = 0 C he indications given above will result in a flow rate equal to,7 m /h with a useful hydraulic head at the circulator of,8 mh O. NOE. Curves obtained with circulator set to constant speed, level III mode. 9 8 Hydraulic head [mh O] 7 R8RY0,8 mh O C B 0 0,7 m /h 0 0,,, Flow rate [m /h] t Power [kw] A t 0 t 0 t 0 Power Δt Flow rate Hydraulic head R8R unit curve Power required by the heating/cooling system zone downstream of the R8R distribution unit emperature difference between delivery and return of the heating/cooling system zone downstream of the R8R distribution unit (Δt depends on the type of system) Operational flow rate downstream of the R8R distribution unit Hydraulic head available downstream of the R8R distribution unit Operational curve of the R8R distribution unit (Wilo Yonos Para circulator + all various components)

16 Standards reference PED 0/8/EU, article. LVD 0//EU EMC 0/0/EU RoHS 0//EU ErP 009//CE ErP 0 Product specifications R8RY0 Distribution unit to control heating and cooling of one system zone. Connections: system side F ISO 8; boiler side / M ISO 8; delivery and return outputs centre distance mm. Includes: brass delivery output equipped with lowenergy consumption circulator complying with directive ErP 009//CE (centre distance 80 mm) and interception ball with integrated thermometer (0 0 C scale); brass return output equipped with interception ball with integrated thermometer (0 0 C scale) and POM check. Reversible delivery and return outputs. EPP rigid insulation (density kg/m). Wall-mount plate (screw anchors not included). EPDM gaskets. emperature range 00 C. Max. working pressure 0 bar. Weight,8 kg. Optional installation of differential by-pass kit between the two delivery and return outputs. Optional installation of interception ball upstream of distribution unit. R8RY Distribution unit to control heating and cooling of one system zone. Connections: system side F ISO 8; boiler side / M ISO 8; delivery and return outputs centre distance mm. Includes: brass delivery output equipped with spacer to install circulator (centre distance 80 mm) and interception ball with integrated thermometer (0 0 C scale); brass return output equipped with interception ball with integrated thermometer (0 0 C scale) and POM check. Reversible delivery and return outputs. EPP rigid insulation (density kg/m). Wall-mount plate (screw anchors not included). EPDM gaskets. emperature range 00 C. max. working pressure 0 bar. Weight,0 kg. Optional installation of differential by-pass kit between the two delivery and return outputs. Optional installation of interception ball upstream of distribution unit. R8RY0 Distribution unit to control heating and cooling of one system zone. Connections: system side F ISO 8; boiler side / M ISO 8; delivery and return outputs centre distance mm. Includes: brass delivery output equipped with low-energy consumption circulator complying with directive ErP 009//CE (centre distance 80 mm), interception ball with integrated thermometer (0 0 C scale) and motorizable mixing ball ; brass return output equipped with interception ball with integrated thermometer (0 0 C scale) and POM check. Reversible delivery and return outputs. EPP rigid insulation (density kg/m). Wall-mount plate (screw anchors not included). EPDM gaskets. emperature range 00 C. Max. working pressure 0 bar. Weight,8 kg. Optional installation of differential by-pass kit between the two delivery and return outputs. Optional installation of interception ball upstream of distribution unit. Optional installation of the mixing actuator controllable by KLIMAbus thermoregulation items. R8RY Distribution unit to control heating and cooling of one system zone. Connections: system side F ISO 8; boiler side / M ISO 8; delivery and return outputs centre distance mm. Includes: brass delivery output equipped with spacer to install circulator (centre distance 80 mm), interception ball with integrated thermometer (0 0 C scale) and motorizable mixing ball ; brass return output equipped with interception ball with integrated thermometer (0 0 C scale) and POM check. Reversible delivery and return outputs. EPP rigid insulation (density kg/m). Wall-mount plate (screw anchors not included). EPDM gaskets. emperature range 00 C. Max. working pressure 0 bar. Weight,0 kg. Optional installation of differential by-pass kit between the two delivery and return outputs. Optional installation of interception ball upstream of distribution unit. Optional installation of the mixing actuator controllable by KLIMAbus thermoregulation items.

17 R8RY0 Distribution unit to control heating and cooling of one system zone. Connections: system side F ISO 8; boiler side / M ISO 8; delivery and return outputs centre distance mm. Includes: brass delivery output equipped with low-energy consumption circulator complying with directive ErP 009//CE (centre distance 80 mm), interception ball with integrated thermometer (0 0 C scale) and motorizable sector mixing equipped with optional fix by-pass; brass return output equipped with interception ball with integrated thermometer (0 0 C scale) and POM check. Reversible delivery and return outputs. EPP rigid insulation (density kg/m). Wall-mount plate (screw anchors not included). EPDM. gaskets emperature range 00 C. Max. working pressure 0 bar. Weight,7 kg. Optional installation of differential by-pass kit between the two delivery and return outputs. Optional installation of interception ball upstream of distribution unit. Optional installation of mixing actuator controllable by KLIMAbus thermoregulation items. R8RY Distribution unit to control heating and cooling of one system zone. Connections: system side F ISO 8; boiler side / M ISO 8; delivery and return outputs centre distance mm. Includes: brass delivery output equipped with spacer to install circulator (centre distance 80 mm), interception ball with integrated thermometer (0 0 C scale) and motorizable sector mixing equipped with optional fix by-pass; brass return output equipped with interception ball with integrated thermometer (0 0 C scale) and POM check. Reversible delivery and return outputs. EPP rigid insulation (density kg/m). Wall-mount plate (screw anchors not included). EPDM gaskets. emperature range 00 C. Max. working pressure 0 bar. Weight,9 kg. Optional installation of differential by-pass kit between the two delivery and return outputs. Optional installation of interception ball upstream of distribution unit. Optional installation of mixing actuator controllable by KLIMAbus thermoregulation items. R8RY0 Distribution unit to control heating and cooling of one system zone. Connections: system side F ISO 8; boiler side / M ISO 8; delivery and return outputs centre distance mm. Includes: brass delivery output equipped with low-energy consumption circulator complying with directive ErP 009//CE (centre distance 80 mm), interception ball with integrated thermometer (0 0 C scale) and thermostatic mixing ; brass return output equipped with interception ball with integrated thermometer (0 0 C scale) and POM check. Reversible delivery and return outputs. EPP rigid insulation (density kg/m). Wall-mount plate (screw anchors not included). EPDM gaskets. emperature range 9 C. Max. working pressure bar. Weight 7,0 kg. Optional installation of differential by-pass kit between the two delivery and return outputs. Optional installation of interception ball upstream of distribution unit. R8RY Distribution unit to control heating and cooling of one system zone. Connections: system side F ISO 8; boiler side / M ISO 8; delivery and return outputs centre distance mm. Includes: brass delivery output equipped with spacer for to install circulator (centre distance 80 mm), interception ball with integrated thermometer (0 0 C scale) and thermostatic mixing ; brass return output equipped with interception ball with integrated thermometer (0 0 C scale) and POM check. Reversible delivery and return outputs. EPP rigid insulation (density kg/m). Wall-mount plate (screw anchors not included). EPDM gaskets. emperature range 9 C. Max. working pressure bar. Weight, kg. Optional installation of differential by-pass kit between the two delivery and return outputs. Optional installation of interception ball upstream of distribution unit. Safety Warning. Installation, commissioning and periodical maintenance of the product must be carried out by qualified operators in compliance with national regulations and/or local standards. A qualified installer must take all required measures, including use of Individual Protection Devices, for his and others safety. An improper installation may damage people, animals or objects towards which may not be held liable. Package Disposal. Carton boxes: paper recycling. Plastic bags and bubble wrap: plastic recycling. Additional information. For more information, go to giacomini.com or contact our technical assistance service. his document provides only general indications. may change at any time, without notice and for technical or commercial reasons, the items included herewith. he information included in this technical sheet do not exempt the user from strictly complying with the rules and good practice standards in force. Product Disposal. Do not dispose of product as municipal waste at the end of its life cycle. Dispose of product at a special recycling platform managed by local authorities or at retailers providing this type of service. 7