ESM x35 DIN Size Digital Process Indicator. ESM x 35 DIN Size Digital Process Indicator

Transcription

1 ESM x35 DIN Sze Dgtal rocess Indcator ESM x 35 DIN Sze Dgtal rocess Indcator - 4 Dgts dsplay - Easly adjustable from front panel - Confgurable dsplay scale between and Adjustable decmal pont - Selectable unversal process Input (0-10 V, 0-1 V, 0-60 mv, 0-20 ma,4-20 ma ) - Adjustable nput flter - Maxmum and mnmum measurement value are regstered to the devces memory - Maxmum or mnmum measurement value can be shown contnuously on the dsplay - User can be adjust devce s readng value for selected nput type - Alarm output Relay or SSR drver output (It must be determned n order.) - Adjustable alarm set value from front panel - rogrammng mode password protecton Instructon Manual. ENG ESM V01 07/08

2 ABOUT INSTRUCTION MANUAL Instructon manual of ESM-3700 Dgtal rocess Indcator conssts of two man sectons. Explanaton of these sectons are below. Also, there are other sectons whch nclude order nformaton and techncal specfcatons of the devce. All ttles and page numbers n nstructon manual are n CONTENTS secton. User can reach to any ttle wth secton number. Installaton: In ths secton, physcal dmensons of the devce, panel mountng, electrcal wrng, physcal and electrcal nstallaton of the devce to the system are explaned. Operaton andarameters: In ths secton user nterface of the devce, accessng to the parameters, descrpton of the parameters are explaned. Also n these sectons, there are warnngs to prevent serous njury whle dong the physcalandelectrcal mountngorusngthedevce. Explanaton of the symbols whch are used n these sectons are gven below. Ths symbol s used for safety warnngs. User must pay attenton to these warnngs. Ths symbol s used to determne the dangerous stuatons as a result of an electrc shock. User must pay attenton to these warnngs defntely. Ths symbol s used to determne the mportant notes about functons and usage of the devce. 2

3 Contents 1.REFACE... age GENERAL SECIFICATIONS 1.2 ORDERING INFORMATION 1.3 WARRANTY 1.4 MAINTENANCE 2.INSTALLATION... age GENERAL DESCRITION 2.2 FRONT VIEW AND DIMENSIONS OF ESM-3700 DIGITAL ROCESS INDICATOR WITH ALARM OUTUT 2.3 FRONT VIEW AND DIMENSIONS OF ESM-3700 DIGITAL ROCESS INDICATOR WITHOUT ALARM OUTUT 2.4 ANEL CUT-OUT 2.5 ENVIRONMENTAL RATINGS 2.6 ANEL MOUNTING 2.7 INSTALLATION FIXING CLAM 2.8 REMOVING FROM THE ANEL 3.ELECTRICAL WIRING... age TERMINAL LAYOUT AND CONNECTION INSTRUCTIONS 3.2 ELECTRICAL WIRING DIAGRAM 3.3 VIEW OF THE DEVICE LABEL 3.4 SULY VOLTAGE INUT CONNECTION OF THE DEVICE 3.5 ROCESS INUT CONNECTION ROCESS INUT CONNECTION OF SERIAL TRANSMITTER WITH CURRENT OUTUT (LOO OWERED) ROCESS INUT CONNECTION OF 3-WIRE TRANSMITTER WITH CURRENT OUTUT ROCESS INUT CONNECTION OF TRANSMITTER WITH VOLTAGE OUTUT 3.6. GALVANIC ISOLATION TEST VALUE OF ESM-3700 DIGITAL ROCESS INDICATOR 3.7 ALARM OUTUT CONNECTIONS RELAY OUTUT CONNECTION SSR DRIVER OUTUT CNNECTION 4. FRONT ANEL DEFINETION AND ACCESSING TO THE MENUS FRONT ANEL DEFINETION OF DEVICE WITH ALARM OUTUT 4.2 FRONT ANEL DEFINETION OF DEVICE WITHOUTALARM OUTUT 4.3 OBSERVATION OF THE SOFTWARE REVISION ON THE DISLAY 4.4 CHANGING AND SAVING ALARM SET VALUE 4.5 ROGRAMMING MODE ARAMETER LIST 4.6 OERATION GRAHICS OF ALARM OUTUTAND ALARM TYES 4.7 EY ACCESSING DIAGRAM OF ROGRAMMING MODE ARAMETERS DEVICE WITH ALARM OUTUT DEVICE WITHOUT ALARM OUTUT age ENTERING TO THE ROGRAMMING MODE, CHANGING AND SAVING ARAMETERS 5.DISLAY FUNCTIONS... age 28 6.UNIVERSAL INUT USER READING ADJUSTMENT OERATION... age 29 7.FAILURE MESSAGES IN ESM 3700 DIGITAL ROCESS INDICATOR... age 31 8.SECIFICATIONS... age 32 3

4 EU DECLARATION OF CONFORMITY Manufacturer Company Name : Emko Elektronk A.S. Manufacturer Company Address: DOSAB, Karanfl Sokak, No:6, Bursa, Turkye The manufacturer hereby declares that the product conforms to the followng standards and condtons. roduct Name : Dgtal rocess Indcator Model Number : ESM-3700 Type Number : ESM-3700 roduct Category : Electrcal equpment for measurement, control and laboratory use Conforms to the followng drectves : 73 / 23 / EEC The Low Voltage Drectve as amended by 93 / 68 / EEC 89 / 336 / EEC The Electromagnetc Compatblty Drectve Has been desgned and manufactured accordng to the followng specfcatons EN :2001 EMC Generc Emsson Standard for the Industral Envronment EN :2001 EMC Generc Immunty Standard for the Industral Envronment EN :2001 Safety Requrements for electrcal equpment for measurement, control and laboratory use. 4

5 1.reface ESM-3700 seres Dgtal rocess Indcators are desgn for measurng the process value. They can be used n many applcatons wth ther easy use, alarm output, unversal process nput propertes. Some applcaton felds whch they are used are below: Applcaton Felds Glass lastc etro-chemstry Textle Automotve Machne producton sector Applcatons Transmtter applcaton of temperature, pressure, humdty etc. Speed measurement of motor drver Current measurement over the shunt resstance 1.1 General Specfcatons Standard 230 V (±%15), 50/60 Hz Optonal ower Supply 115 V (±%15), 50/60 Hz 24 V (±%15), 50/60 Hz 24 V (-%15, + %10), 50/60Hz ESM-3700 ower Supply Input (0-10 V ) (0-1 V ) (0-60 mv ) (0-20 ma ) (4-20 ma ) rocess Input Optonal Alarm Output (Relay Output) Optonal Alarm Output (SSR Drver Output) Alarm Output 5

6 1.2 Orderng Informaton A BC D E / FG HI / U V W Z ESM-3700 (77 x 35 DIN Sze) 0 / / A Supply Voltage 2 24 V ( -%15, +%10 ) 50/60 Hz 3 24 V ( ± 15% ) 50/60 Hz V ( ± 15% ) 50/60 Hz V ( ± 15% ) 50/60 Hz 9 Customer BC Input Type Scale 20 Confgurable (Table-1) Table-1 E Alarm Output 0 None 1 Relay Output (resstve load 5 A@250 V,1NO + 1NC) 2 SSR Drver Output (Maxmum 10 ma@5 V ) Table-1 BC Input Type( Voltage/Current) mv V V ma ma Scale -1999, , , , , 9999 All order nformaton of ESM-3700 Dgtal rocess Indcator are gven on the table at left. User may form approprate devce confguraton from nformaton and codes that at the table and convert t to the orderng codes. Frstly, supply voltage then other specfcatons must be determned. lease fll the order code blanks accordng to your needs. lease contact us, f your needs are out of the standards. Vac, Vdc, Vac/dc In the current measurement mode, the nput empedance of the devce s 5 Because of ths reason a voltage nput shouldn t be connected to the process nput of the devce, whle the devce s n the current measurement mode, otherwse process nput can be damaged. To change the process nput type from voltage to current whle the devce s operatng, frst separate the voltage nput then, change the nput type to currrent and connect to current to the process nput. 1.3 Warranty EMKO Elektronk warrants that the equpment delvered s free from defects n materal and workmanshp. Ths warranty s provded for a perod of two years. The warranty perod starts from the delvery date. Ths warranty s n force f duty and responsbltes whch are determned n warranty document and nstructon manual performs by the customer completely. 1.4 Mantenance Repars should only be performed by traned and specalzed personnel. Cut power to the devce before accessng nternal parts. Do not clean the case wth hydrocarbon-based solvents (etrol, Trchlorethylene etc.). Use of these solvents can reduce the mechancal relablty of the devce. Use a cloth dampened n ethyl alcohol or water to clean the external plastc case. 6

7 2.Installaton Before begnnng nstallaton of ths product, please read the nstructon manual and warnngs below carefully. In package, - One pece unt - Two peces mountng clamps - One pece nstructon manual A vsual nspecton of ths product for possble damage occured durng shpment s recommended before nstallaton. It s your responsblty to ensure that qualfed mechancal and electrcal techncans nstall ths product. If there s danger of serous accdent resultng from a falure or defect n ths unt, power offthesystem and separatetheelectrcalconnectonofthedevcefromthesystem. The unt s normally suppled wthout a power supply swtch or a fuse. Use power swtch and fuse as requred. Be sure to use the rated power supply voltage to protect the unt aganst damage and to prevent falure. Keep the power off untl all of the wrng s completed so that electrc shock and trouble wth the unt can be prevented. Never attempt to dsassemble, modfy or repar ths unt. Tamperng wth the unt may results n malfuncton, electrc shock or fre. Do not use the unt n combustble or explosve gaseous atmospheres. Durng the equpment s putted n hole on the metal panel whle mechancal nstallaton some metal burrs can cause njury on hands, you must be careful. Montage of the product on a system must be done wth t s fxng clamps. Do not do the montage of the devce wth napproprate fxng clamp. Be sure that devce wll not fall whle dong the montage. It s your responsblty f ths equpment s used n a manner not specfed n ths nstructon manual. 7

8 2.1 General Descrpton Mountng Clamp Front anel I65 protecton NEMA 4X anel surface (maxmum thckness 15 mm / 0.59 nch) 2.2 Front Vew and Dmensons of ESM-3700 Dgtal rocess Indcator Wth Alarm Output Maxmum 15 mm / 0.59 nch rocess Indcator ESM ET 35 mm / 1.38 nch 77 mm / 3.03 nch 4 mm / 0.16 nch 58.5 mm / 2.30 nch 8

9 2.3 Front Vew and Dmensons of ESM-3700 Dgtal rocess Indcator Wthout Alarm Output Maxmum 15 mm / 0.59 nch rocess Indcator ESM mm / 1.38 nch 2.4 anel Cut-Out 110 mm / 4.33 nch (mn) 29 mm / 1.14 nch 50 mm / 1.97 nch (mn) 77 mm / 3.03 nch 58,5 mm / 2.30 nch 4 mm / 0.16 nch 71 mm / 2.79 nch 9

10 2.5 Envronmental Ratngs Operatng Condtons Operatng Temperature : 0to50 C Max. Operatng Humdty : 90 % Rh (non-condensng) Alttude : Up to 2000 m. Forbdden Condtons: Corrosve atmosphere Explosve atmosphere Home applcatons (The unt s only for ndustral applcatons) 2.6 anel Mountng 1-Before mountng the devce n your panel, make sure that the cut-out s of the rght sze. 1 2-Insert the devce through the cut-out. If the mountng clamps are on the unt, put out them before nsertng the unt to the panel. 2 Durng nstallaton nto a metal panel, care should be taken to avod njury from metal burrs whch mght be present. The equpment can loosen from vbraton and become dslodged f nstallaton parts are not properly tghtened. These precautons for the safety of the person who does the panel mountng. 10

11 2.7 Installaton Fxng Clamp 1 The unt s desgned for panel mountng. 1-Insert the unt n the panel cut-out from the front sde. 2- Insert the mountng clamps to the fxng sockets that located left and rght sdes of devce and make the unt completely mmoble wthn the panel Chazýn Removng anel fromüzernden the anelçýkarýlmasý Montage of the unt to a system must be done wth t s own fxng clamps. Do not do the montage of the devce wth napproprate fxng clamps. Be sure that devce wll not fall whle dong the montage. Before startng to remove the unt from panel, power off the unt and the related system. 1-ull mountng clamps from left and rght fxng sockets. 2-ull the unt through the front sde of the panel

12 3.Electrcal Wrng You must ensure that the devce s correctly confgured for your applcaton. Incorrect confguraton could result n damage to the process beng controlled, and/or personal njury. It s your responsblty, as the nstaller, to ensure that the confguraton s correct. Devce parameters has factory default values. These parameters must be set accordng to the system s needs. Only qualfed personnel and techncans should work on ths equpment. Ths equpment contans nternal crcuts wth voltage dangerous to human lfe. There s severe danger for human lfe n the case of unauthorzed nterventon. Be sure to use the rated power supply voltage to protect the unt aganst damage and to prevent falure. Keep the power off untl all of the wrng s completed so that electrc shock and trouble wth the unt can be prevented. 3.1 Termnal Layout and Connecton Instructons Screw drver 0,8x3mm Torque 0,5 Nm Max. 2.5 mm / nch Wre Sze: 14 AWG/1 mm² Sold /Stranded 12

13 3.2 Electrcal Wrng Dagram Electrcal wrng of the devce must be the same as Electrcal Wrng Dagram below to prevent damage to the process beng controlled and personnel njury. /N : ESM-3700 CAT II OUTUT 5 A@250 V NO C NC For SSr Output (+) (-) L N 0-20mA 4-20mA 0-60mV 0-1V 0-10V Unversal rocess Input ( Voltage/Current) Relay or SSR Drver Output (Ths Output exst n devce wth Alarm Output.) Voltage Output 12 V ( ± 35% ) Max. 30 ma Supply Voltage Input 230 V ( ± %15 ) 50/60 Hz VA 115 V ( ± %15 ) 50/60 Hz VA 24 V ( ± %15 ) 50/60 Hz VA 24 V ( -%15, +%10 ) 50/60 Hz VA (It must be determned n order) rocess Input s n CAT II class. 13

14 3.3 Vew of the Devce Label Devce Label for Unversal rocess Input, 230V Supply Voltage Input and Alarm Relay Output /N : ESM /00.00/ OUTUT 230 V ± 15% 5A@250V 50/60Hz - 1.5VA L N NO C NC V ± 30% Max. 30 ma CAT II Voltage Input 0-60mV, 0-1V, 0-10V Current Input 0-20mA, 4-20mA Devce Label for Unversal rocess Input, 230V Supply Voltage Input and Wthout Alarm Output /N : ESM /00.00/ V ± 15% 50/60Hz - 1.5VA L N CAT II V ± 30% Max. 30 ma Voltage Input 0-60mV, 0-1V, 0-10V Current Input 0-20mA, 4-20mA 14

15 3.4 Supply Voltage Input Connecton of the Devce Connecton of Supply Voltage Input L 4 N 5 Note-1 External Fuse (1 A T) Note-2 ower Supply Swtch Supply Voltage 230 V (± %15) 50/60 Hz or 115 V (± %15) 50/60 Hz or 24 V (± %15) 50/60 Hz or 24 V (-%15,+%10) 50/60 Hz Note-1: L s (+), N s (-) for 24V Supply Voltage Note-2: External Fuse s recommended Make sure that the power supply voltage s same ndcated on the nstrument. Swtch on the power supply only after that all the electrcal connecton have been completed. Supply voltage range must be determned n order. Whle nstallng the unt, supply voltage range must be controlled and approprate supply voltage must be appled to the unt. Controllng prevents damages n unt and system and possble accdents as a result of ncorrect supply voltage. There s no power supply swtch or fuse on the devce. So a power supply swtch and a fuse must be added to the supply voltage nput. ower supply swtch and fuse must be put to a place where user can reach easly. ower supply swtch must be two poled for seperatng phase and neutral. On/Off condton of power supply swtch s very mportant n electrcal connecton. On/Off condton of power supply swtch must be sgned for preventng the wrong connecton. External fuse must be on phase connecton n supply nput. External fuse must be on (+) lne connecton n supply nput. 15

16 3.5 rocess Input Connecton rocess Input Connecton of Seral Transmtter wth Current Output (Loop owered) Transmtter connecton by usng supply voltage on the devce Transmtter connecton by usng external supply voltage source 12 V ( ± 35% ) Max. 30 ma Transmtter ma V Transmtter rocess Input Connecton of 3-Wre Transmtter wth Current Output External ower Supply Note 1 Note 1 : External power supply must be selected accordng to supply voltage range and requred current for transmtter Input Empedance V ( ± 35% ) Max. 30 ma ma V Transmtter connecton by usng supply voltage on the devce Transmtter connecton by usng external supply voltage source ma V ma V External ower Supply Note 1 12 V (±35%) Max. 30 ma Transmtter 12V ( ± 35% ) Max. 30 ma Transmtter Note 1 : External power supply must be selected accordng to supply voltage range and requred current for transmtter. Input Empedance5. 16

17 3.5.3 rocess Input Connecton of Transmtter wth Voltage Output Transmtter connecton by usng supply voltage on the devce Transmtter connecton by usng external supply voltage source mv, V V mv, V V External ower Supply Note 1 12 V (±35%) Max. 30 ma Transmtter 12V ( ± 35% ) Max. 30 ma Transmtter Note 1 : External power supply must be selected accordng to supply voltage range and requred current for transmtter. InputEmpedance11k For mV rocessinput InputEmpedance11k For 0...1V rocessinput InputEmpedance11k For V rocessinput 3.6 Galvanc Isolaton Test Values of ESM-3700 Dgtal rocess Indcator Supply Voltage Input V ( For ESM ) 500 V ( For ESM ) Ground V Optonal Alarm Output Relay Output V 2000 V 2000 V Optonal 1 Alarm Output 1 2 SSR Drver Output 2 11 rocess Input V V 10 Voltage Output 17

18 3.7 Alarm Output Connectons Relay Output Connecton Devce L N NC C 3 2 Max 5 A T Fuse NO 1 Load Fuses must be selected accordng to the applcaton SSR Drver Output Connecton Devce 2 Last Control Element (SSR) L N 1 5V Max. 10 ma Fuse Load Fuses must be selected accordng to the applcaton. 18

19 4. Front anel Defneton and Accessng to the Menus 4.1 Front anel Defneton of Devce Wth Alarm Output Alarm Output Actve Led Led Indcaton of Alarm Set Value Changng Mode s Actve Led Indcaton of rogrammng Mode s Actve Note-1 It s used to ncrease the value, n man operaton ESM screen show the maxmum measurement process value, n programmng mode It s used to access to the ET parameter Dsplay rocess Value, Alarm Set Value and arameters rocess Indcator Note-1 It s used to decrease the value, n man operaton screen show the mnmum measurement process It s used to enter to the Alarm Set Value Changng Mode, rogrammng Mode and used as OK button Note-1: If ncrement or decrement button s pressed for 5 seconds contnuously, ncrement and decrement number become 10, f ncrement or decrement button s pressed for 10 seconds contnuously, ncrement and decrement number become 100, f ncrement or decrement button s pressed for 15 seconds contnuously, ncrement and decrement number become Front anel Defneton of Devce Wthout Alarm Output Dsplay rocess Value and arameters Led Indcaton of rogrammng Mode s Actve Note-2 It s used to ncrease the value, n man operaton ESM screen show the maxmum measurement process value, n programmng mode It s used to access to the parameter rocess Indcator Note-2 It s used to decrease the value, n man operaton screen show the mnmum measurement process value It s used to enter to the rogrammng Mode and used as OK button Note-2: If ncrement or decrement button s pressed for 5 seconds contnuously, ncrement and decrement number become 10, f ncrement or decrement button s pressed for 10 seconds contnuously, ncrement and decrement number become 100, f ncrement or decrement button s pressed for 15 seconds contnuously, ncrement and decrement number become

20 4.3 Observaton of Software Revson on the Dsplay When power s frst appled to the dgtal process ndcator, software revson number s shown on the dsplay. ESM ET rv Revson rocess Indcator ESM Software revson number ET rocess Indcator Man Operaton Screen s shown If there s an unexpected stuaton whle openng the devce, power off the devce and nform a qualfed personnel. 4.4 Changng and Savng Alarm Set Value Man Operaton Screen Alarm Set Value Screen ET ET When ET/ENTER button s pressed, led lghts on and alarm set value s shown on the dsplay. Change the alarm set value wth ncrement and decrement buttons. Alarm Set Value Screen Man Operaton Screen ET ET ress ET/ENTER button for savng the alarm set value led lghts off and man operaton screen s shown. Alarm set value can be adjusted from low readng adjustment value parameter to up readng adjustment value parameter. (Alarm set value changng mode s actve n devces wth alarm output.) If no operaton s performed n Alarm set value changng mode for 20 seconds, devce turns to man operaton screen automatcally. 20

21 4.5. rogrammng Mode arameter Lst rocessinputtypeselectonarameter ( Default =0) rocess Input type s determned wth ths parameter. It can be adjusted from 0 to V ( ; 9999 ) V ( ; 9999 ) mv ( ; 9999 ) ma ( ; 9999 ) ma ( ; 9999 ) rocessinputflterselectonarameter ( Default =0) rocess Input flter s determned wth ths parameter. It can be adjusted from 0 to 4. Measurement s performed at each; 240msfor mA and mAprocessnputtype 150 ms for mv process Input type 100msfor0...1V and V processinputtype The last measurement value s shown. The average of last 2 measurement value s shown. The average of last 4 measurement value s shown. The average of last 8 measurement value s shown. The average of last 16 measurement value s shown. DsplayFunctonSelectonarameter ( Default =0) In man operaton screen dsplayed process value s determned wth ths parameter. It can be adjusted from 0 to 2 The measurement process value s shown on the dsplay The mnmum measurement process value s shown contnuously on the dsplay The maxmum measurement process value s shown contnuously on the dsplay Decmalontostonarameter ( Default =0) Decmal pont poston s determned wth ths parameter. It can be adjusted from 0 to 3 No pont If no operaton s performed n rogrammng mode for 20 seconds, devce turns to man operaton screen automatcally. 21

22 LowReadngAdjustmentValuearameter ( Default = ) It defnes mnmum value for dual pont readng adjustment ýt can be adjusted to ( -1) UpReadngAdjustmentValuearameter( Default =9999 ) It defnes maxmum value for dual pont readng adjustment ýt can be adjusted ( +1) to 9999 ReadngAdjustmentSelectonarameter ( Default =0) It defnes whch readng adjustment type s actve. It can be adjusted from 0 to 1 Selected process nput type s read accordng to the standard readng adjustment. Selected process nput type s read accordng to the user readng adjustment. and parameters are observed f readng adjustment selecton parameter = 1, otherwse these parameters are can not be observed. User Readng Adjustment Low Lmt Analogue Value arameter In ths parameter, the equvalent voltage or current for low readng adjustment value parameter s determned.( lease refer to secton 6. ) User Readng Adjustment Up Lmt Analogue Value arameter In ths parameter, the equvalent voltage or current for up readng adjustment value parameter s determned. ( lease refer to secton 6. ) AlarmHysteressarameter ( Default =0) Alarm hysteress value. Itcanbeadjustedfrom0to ( - ) / 2 AlarmTypeSelectonarameter ( Default =1) roses Hgh Alarm roses Low Alarm AlarmOnDelayTmearameter ( Default =0) It can be adjusted from 0 to 99 mnutes. AlarmOffDelayTmearameter ( Default =0) It can be adjusted from 0 to 99 mnutes. When ths parameter s 99, f ncrement button s pressed, s observed and alarm latchng output s selected. To make the alarm latchng output passve, decrement button must be pressed n man operaton screen. AlarmDelayarameterAfterowerOn ( Default =0) Ths parameter defnes the delay for the alarm s beng actve after power on. It can be adjusted from 0 to 99 mnutes. rogrammngmodeacessngassword ( Default =0) assword for enterng to the programmng mode s defned wth ths parameter. It can be adjusted from 0 to ýf t s 0, programmng mode s accessed wthout enterng password.,,,, parameters are actve n devce wth alarm output. If no operaton s performed n rogrammng mode for 20 seconds, devce turns to man operaton screen automatcally. 22

23 4.6 Operaton Graphcs of Alarm Output and Alarm Types ower ower = ( Alarm latchng output s selected ) Alarm Status Tme Alarm Status Tme Tme Tme Alarm Output Actve Led Tme Alarm Output Actve Led Decrement button must be pressed to make alarm output s passve Tme Alarm Output Alarm Output Tme Tme rocess Hgh Alarm Alarm Output ON OFF rocess Value rocess Low Alarm Alarm Output ON OFF rocess Value =Alarm Set Value 23

24 4.7 Easy Accessng Dagram of rogrammng Mode arameters Devces Wth Alarm Output 5 secs ET ET ET Man Operaton Screen rogrammng Mode Enterng Screen assword Enterng Screen Enter password wth ncrement and decrement buttons ET ET ET assword Enterng Screen ress ENTER button for accessng parameter rocess Input Type Selecton arameter rocess Input Flter Selecton arameter ET ET ET Dsplay Functon Selecton parameter Decmal ont oston arameter Low Readng Adjustment Value arameter ET ET ET Up Readng Adjustment Value arameter Readng Adjustment Selecton arameter User Readng Adjustment Low Lmt Analogue Value arameter ET ET ET User Readng Adjustment Up Lmt Analogue Value arameter Alarm Hysteress arameter Alarm Type Selecton arameter ET ET ET Alarm On Delay Tme arameter Alarm Off Delay Tme arameter Alarm Delay arameter After ower On ET rogrammng Mode Accessng assword If no operaton s performed n rogrammng mode for 20 seconds, devce turns to man operaton screen automatcally. 24

25 4.7.2 Devces Wthout Alarm Output 5 secs ET ET ET Man Operaton Screen rogrammng Mode Enterng Screen assword Enterng Screen Enter password wth ncrement and decrement buttons ET ET ET assword Enterng Screen ress ENTER button for accessng parameter rocess Input Type Selecton arameter rocess Input Flter Selecton arameter ET ET ET Dsplay Functon Selecton parameter Decmal ont oston arameter Low Readng Adjustment Value arameter ET ET ET Up Readng Adjustment Value arameter Readng Adjustment Selecton arameter User Readng Adjustment Low Lmt Analogue Value arameter ET ET User Readng Adjustment Up Lmt Analogue Value arameter rogrammng Mode Accessng assword If no operaton s performed n rogrammng mode for 20 seconds, devce turns to man operaton screen automatcally. 25

26 4.8 Enterng to the rogrammng Mode, Changng and Savng arameters Man Operaton Screen rogrammng Screen ET ET When ENTER button s pressed for 5 seconds. led starts to blnk. If programmng mode enterng password s dfferent from 0, programmng mode enterng screen s observed. Note-1: If programmng mode accessng password s 0, process nput type selecton parameter screen s observed nstead of programmng mode accessng screen Note-2: arameters can be observed by pressng ENTER button n programmng mode accessng screen wthout enterng programmng mode accessng password. But parameters can not be changed. rogrammng Mode Accessng Screen ress ncrement button for accessng to the password enterng screen. assword Enterng Screen Enter programmng mode accessng password wth ncrement and decrement buttons ET rogrammng Screen ET ET assword Enterng Screen ress ENTER button for accessng to the parameters rocess Input Type Selecton arameter ress ncrement button for accessng to the parameter value. ress ENTER button for accessng to the next parameter ET ET rocess Input Type Selecton Value Change the value wth ncrement and decrement buttons rocess Input Type Selecton Value ress ENTER button for savng the parameter value If no operaton s performed n rogrammng mode for 20 seconds, devce turns to man operaton screen automatcally. 26

27 rogrammng Screen rogrammng Screen ET ET rocess Input Type Selecton arameter ress ENTER button for accessng to the next parameter rocess Input Flter Selecton arameter ress ncrement button for accessng to the parameter value. ress ENTER button for accessng to the next parameter ET ET rocess Input Flter Selecton Value Change the value wth ncrement and decrement buttons rocess Input Flter Selecton Value ress ENTER button for savng the parameter value rogrammng Screen ET rocess Input Flter Selecton arameter ress ENTER button for accessng to the next parameter Other programmng mode parameters can be accessed wth same method explaned above, observed and changed If no operaton s performed n rogrammng mode for 20 seconds, devce turns to man operaton screen automatcally. 27

28 5. Dsplay Functons ET ET In man operaton screen, If ncrement button s pressed then the maxmum measurement value s shown on the dsplay ET ET In man operaton screen, If decrement button s pressed then the mnmum measurement value s shown on the dsplay ET ET In man operaton screen, If decrement and ENTER buttons are pressed together the maxmum and mnmum measurement value areresettothemeasurement value at that tme. The message s shown on the dsplay 28

29 6. Unversal Input User Readng Adjustment Operaton Man Operaton Screen rogrammng Screen ET ET Access to the readng adjustment selecton parameter as explaned n secton and Readng Adjustment Selecton arameter ress ncrement button for accessng to the parameter value. ress ENTER button for accessng to the next parameter ET ET Readng Adjustment Selecton Value (Standard readng adjusment s selected) Readng Adjustment Selecton Value (User readng adjusment s selected) Change the value wth ncrement and decrement buttons ress ENTER button for savng the parameter value rogrammng Screen rogrammng Screen ET ET Readng Adjustment Selecton arameter ress ENTER button for accessng to the next parameter User Readng Adjustment Low Lmt Analogue Value arameter ress ncrement button for accessng to the user readng adjustment low lmt analogue value enterng screen. ress ENTER button for accessng to the next parameter User Readng Adjustment Low Lmt Analogue Value Enterng Screen ress ENTER button for accessng to programmng screen ET At ths state, the equvalent voltage or current for low readng adjustment value parameter s appled to process nput of the devces. When decrement button s press, dsplay starts to blnk. It means, the analogue value at process nput s saved as a user readng adjustment low lmt analogue value If no operaton s performed n rogrammng mode for 20 seconds, devce turns to man operaton screen automatcally. 29

30 rogrammng Screen rogrammng Screen ET ET User Readng Adjustment Low Lmt Analogue Value arameter ress ENTER button for accessng to the next parameter User Readng Adjustment Up Lmt Analogue Value arameter ress ncrement button for accessng to the user readng adjustment up lmt analogue value enterng screen. ress ENTER button for accessng to the next parameter User Readng Adjustment Up Lmt Analogue Value Enterng Screen ress ENTER button for accessng to programmng screen ET At ths state, the equvalent voltage or current for up readng adjustment value parameter s appled to process nput of the devces. When ncrement button s pressed, dsplay starts to blnk. It means, the analogue value at process nput s saved as a user readng adjustment up lmt analogue value ET User Readng Adjustment Up Lmt Analogue Value arameter ress ENTER button for accessng to the next parameter Other programmng mode parameters can be accessed, observed and changed If no operaton s performed n rogrammng mode for 20 seconds, devce turns to man operaton screen automatcally. 30

31 7. Falure Messages n ESM 3700 Dgtal rocess Indcator rocess Indcator ESM ET If the equvalent voltage or current appled to the process nput whle n or parameter for user readng adjustment s out of the standard scale, ths error message are shown on the dsplay Example-1: For process Input type selected as 0-10 V, If the appled voltage whle n parameter or parameter s lower than 0 V or upper than 10 V, when the decrement or ncrement button s pressed for savng the analog value ths errror message s shown on the dsplay and appled voltage value s not saved. ress any button to clear error message from the dsplay and turn to the user readng adjustment analaog value enterng screen rocess Indcator ESM ET If the dfference between the equvalent voltage or current appled to the process nput whle n and parameters for user readng adjustment s lower than the %50 of the standard scale, ths error message are shown on the dsplay Example-2: For process Input type selected as 0-10 V, If the dfference between the appled voltages n and parameters s lower than the 5 V, when the decrement or ncrement button s pressed for savng the analog value ths errror message s shown on the dsplay and appled voltage value s not saved. ress any button to clear error message from the dsplay and turn to the user readng adjustment analaog value enterng screen 31

32 8. Specfcatons Devces Type Housng&Mountng rotecton Class Weght Envronmental Ratng wth none-condensng humdty. o o o o Storage / Operatng Temperature: -40 C to +85 C / 0 C to +50 C Storage / Operatng Humdty Installaton Overvoltage Category olluton Degree Operatng Condtons : Contnuous rocess Input : V Accuracy Samplng Tme Supply Voltage and ower 12V Voltage Output Alarm Relay Output Optonal SSR Output Dsplay LED Approvals : Dgtal rocess Indcator : 77 mm x 35 mm x 62.5 mm lastc housng for panel Mountng. anel cut-out 71 x 29 mm. : NEMA 4X (I65 at front, I20 at rear). : Approxmately 0.16 Kg. : Standard, ndoor at an alttude of less than 2000 meters : 90 % max. (None-condensng) : Fxed Installaton : II. : II. Offce or workplace, none conductve polluton. Input Empedance Approxmately 11 k Measurement range V V Input Empedance Approxmately 11 k Measurement range V mv Input Empedance Approxmately 11k Measurement range mv ma Input Empedance Approxmately 5 Measurement range ma ma Input Empedance Approxmately 5 Measurement range ma : ±0.5% of full scale : Measurement s performed at each 240 ms for ma and ma process nput 150 ms for mv process Input 100 ms for V and V process Input :230 V (-%15;+%15) 50/60 Hz. 1.5 VA 115 V (-%15;+%15) 50/60 Hz. 1.5 VA 24 V (-%15;+%15) 50/60 Hz. 1.5 VA 24 V (-%15, +%10) 50/60 Hz. 1.5 VA : 12 V ( ± 35% ) Max. 30 ma :5 A@250 V at resstve load (Electrcal Lfe : Operaton(Full Load)) :Maxmum 10 ma@5 V :10 mm Red 4 dgts LED Dsplay : Devce wth alarm Output: (Green), (Red), Alarm Output Actve(Red) 3 mm Devce wthout alarm Output: (Red) 3 mm :GOST-R, 32