Versatec Compact 50 Hz Series Installation Manual

Transcription

1 ommercial kW eothermal/water Source Heat Pump 50Hz Installation Information Water Piping onnections Electrical Startup Procedures Troubleshooting Preventive Maintenance Versatec ompact 50 Hz Series Installation Manual IM1252AU 12/18

2

3 VESATE OMPAT SEIES INSTALLATION MANUAL Table of ontents Model Nomenclature eneral Installation Information Dimensional Data Installing Horizontal Units Hanger Bracket Locations Duct System and Water Piping Water Quality ondensate Drain System leaning and Flushing Open Loop round Water Systems Freeze Detection Electrical onnections Electrical Data Blower Performance Data Speed EM onstant Torque Motors Wiring Schematics ontrols - Aurora Base ontrol ontrols - UP (optional) Unit Startup Operating Parameters and Operating Limits Pressure Drop and ompressor esistance Thermistor esistance and efrigerant ircuit uideline Heat of Extraction/ejection Data eference alculations Troubleshooting Startup/Troubleshooting Form Preventive Maintenance eplacement Procedures evision uide

4 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Model Nomenclature UBK V 010 T L A N 16 A 17 N A SS 24 * Model Type UBK Versatec ompact abinet onfiguration V Vertical H - Horizontal Unit apacity acity (kw) 002, 003, 005, 006, 007, 009, 010, 012, 015, 017 Discharge onfiguration T Top (Vertical) E End (Horizontal) ont S Side (Horizontal) ont eturn Air onfiguration L Left ight Voltage /50/1 /1 ( , 012) /50/3 /3 ( ) Future Option 0 None Blower Options 1 Variable Speed EM Blower 4 5-Speed EM Blower ( ) 6 Variable Speed d onstant Torque EM Blower ( ) Water oil Option opper D Insulated opper N upronickel P Insulated upronickel Sound Kit Option A None B Sound Kit Vintage * Factory Use Only Non-Standard Options SS Standard SA Split Access Panel SB Service Ports located to the front of the unit SD Split Access Panel and Service Ports located to the front Drain Pan Option 0 omposite, No Secondary onnection 1 omposite, Secondary onnection 2 Stainless Steel, No Secondary onnection 3 Stainless Steel, Secondary onnection Air oil Option 3 All-Aluminum, Uncoated 4 All-Aluminum, AlumiSeal TM Filter Option A MEV 4 B MEV 13 abinet Option 0 Unpainted abinet, Filter ail 1 Painted abinet, Filter ail 2 Unpainted abinet, 4-Sided Filter ack 3 Painted abinet, 4-Sided Filter ack Electrical Options 1 N No Phase uard, No Disconnect D No Phase uard, Disconnect P Phase uard, No Disconnect B Phase uard, Disconnect ontrol Option A Aurora TM Base ontrol (AB) E Aurora TM UP DD ontroller F Aurora TM UP DD ontroller with LON Water ontrol Option N None Water Flow egulator V 2-Way Valve B 2-Way Valve w/ Water Flow egulator Note: 1 - Phase uard Only Available on /50/3 All Versatec ompact 50Hz product is safety tested to E standards and performance tested in accordance with standard EN

5 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL eneral Installation Information Safety onsiderations WANIN: Before performing service or maintenance operations on a system, turn off main power switches to the indoor unit. If applicable, turn off the accessory heater power switch. Electrical shock could cause personal injury. Installing and servicing heating and air conditioning equipment can be hazardous due to system pressure and electrical components. Only trained and qualified service personnel should install, repair or service heating and air conditioning equipment. Untrained personnel can perform the basic maintenance functions of cleaning coils and cleaning and replacing filters. All other operations should be performed by trained service personnel. When working on heating and air conditioning equipment, observe precautions in the literature, tags and labels attached to the unit and other safety precautions that may apply. Follow all safety codes. Wear safety glasses and work gloves. Use a quenching cloth for brazing operations and have a fire extinguisher available. Moving and Storage Move units in the normal up orientation. Horizontal units may be moved and stored per the information on the packaging. Do not stack more than three units in total height. Vertical units may be stored one upon another to a maximum height of two units. Do not attempt to move units while stacked. When the equipment is received, all items should be carefully checked against the bill of lading to be sure all crates and cartons have been received. Examine units for shipping damage, removing the units from the packaging if necessary. Units in question should also be internally inspected. If any damage is noted, the carrier should make the proper notation on the delivery receipt, acknowledging the damage. Unit Location Locate the unit in an indoor area that allows for easy removal of the filter and access panels. Location should have enough space for service personnel to perform maintenance or repair. Provide sufficient room to make water, electrical and duct connection(s). If the unit is located in a confined space, such as a closet, provisions must be made for return air to freely enter the space by means of a louvered door, etc. Any access panel screws that would be difficult to remove after the unit is installed should be removed prior to setting the unit. On horizontal units, allow adequate room below the unit for a condensate drain trap and do not locate the unit above supply piping. are should be taken when units are located in unconditioned spaces to prevent damage from frozen water lines and excessive heat that could damage electrical components. Installing Vertical Units Vertical units are available in left or right air return configurations. Top flow vertical units should be mounted level on a vibration absorbing pad slightly larger than the base to provide isolation between the unit and the floor. 2 in. PEX Foam Vertical Unit Mounting 5

6 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Vertical Dimensional Data Standard filter rails for open return applications Field installed duct flange Deluxe filter rack for ductable return applications A N S A N Air coil Q Q AESS PANEL B P F FONT Top View - ight eturn AI OIL SIDE M M AI OIL SIDE FONT 2' (61 cm) Alternate Service Access Top View - Left eturn 2' (61 cm) Service Access Left eturn (ight eturn Opposite Side) P F B Isometric View - Left eturn U T W Air coil Air coil AESS PANEL AESS PANEL V H E D 1.6 in (4.1 cm) ondensate 3/4 in PV glue socket 1.6 in (4.1 cm) Water 1 onnections* L J Power supply 1 in (25.4 mm) knockout Low voltage 1/2" (12.7 mm) knockout L K ondensate 3/4 in PV glue socket 1.6 in (4.1 cm) 8 7 Water onnections* E H D 1.6 in (4.1 cm) J L 6 8 AESS PANEL 8 7 K L Front View - ight eturn Front View - Left eturn ight View - ight eturn (J & L) Left View - Left eturn (K & L) NOTE: * Water connections protrude approximately 1.5 in. (3.81cm) from cabinet. 6

7 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Vertical Dimensional Data cont. Vertical Models Electrical Knockouts Overall abinet Water onnections J K L Loop A B D E H 1/2 (1.27cm) cond 1 (2.54cm) cond 1 (2.54cm) cond M Width Depth Height* In Out ondensate Water FPT Low Voltage Low Voltage Power Supply cm mm cm mm cm mm cm mm cm mm cm mm cm mm Filter ack Width Vertical Models Discharge onnection duct flange installed (±0.25 cm) **eturn onnection using deluxe filter rack (±0.25 cm) N P Q S T U V W Supply Width Supply Depth eturn Depth eturn Height cm cm cm cm cm cm cm ondensate is 3/4 PV female glue socket and is switchable from side to front. 2/18/18 *Discharge flange is field installed and extends 1 (25.4 mm) from top of cabinet. **Vertical units shipped with standard 2 (field adjustable to 1 ) open application filter rack extending 2.2 from unit and is not suitable for duct connection, For ductable return connection applications, order the deluxe 2 (field adjustable to 1 ) duct collar/filter rack which extends 3.25 from the unit and is suitable for duct connections. Vertical Disconnect When using disconnect, do not use dimension L from the standard vertical dimensional data. Use dimension LL from the vertical disconnect dimensional data. Vertical Models LL [16.5] 005 [40.1] [47.8] 009 [38.9] [35.1] 015 [36.3] 017 [36.3] Dimensions in cm Power Supply 1.8 in. [4.6 cm] Disconnect Location LL Alternative Power Location Disconnect Located on this Side for a ight eturn Vertical Shown in Left eturn onfiguration 7

8 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Horizontal Dimensional Data ight eturn Standard filter rails 2.5 cm knockout 1.3 cm knockout Front K 5.3 cm 5.3 cm P AP Standard filter rails Front Left eturn J MP E AP MP A ight eturn Air Front View D AP MP 5.3 cm 5.3 cm ondensate "X" PV size End Discharge Side Discharge 2' (61 cm) Service Access E 2 1 P AP MP 1/2 in knockout 1 in knockout Side Discharge ondensate "X" PV size End Discharge Deluxe filter rack option shown D Left eturn Air Front View Deluxe filter rack option shown 5.8 cm N P P N 5.8 cm J K (61 cm) Service Access H FILTE AK AI OIL SIDE BLOWE L OUTLET Legend M AP = Alternate Service Panel M 3 L BP P = Blower Service Panel = ontrol Access Panel BLOWE OUTLET BP MP = ompressor Service Panel A BP A 2.1 ight eturn End Discharge Left eturn End Discharge FILTE AK AI OIL SIDE H P N 3.8 cm 3.8 cm N P BP L M BLOWE OUTLET AP MP K 1/2 in knockout J 1 in knockout Front Front 1" knockout J 1/2 in knockout K AP MP BLOWE OUTLET M L BP ight eturn Side Discharge Left eturn Side Discharge Front Air oil Q S T T S Q FILTE AK ONNETION Deluxe filter rack option (shown) FILTE AK ONNETION Air oil Front Water onnections* B ight eturn Side View B Left eturn Side View Water onnections* NOTE: * Water connections protrude approximately 3.8 cm from cabinet. 8

9 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Horizontal Dimensional Data cont. Horizontal Models Water onnections Electrical Knockouts Overall abinet J K Loop A B D E H 1/2 (1.27cm) cond 1 (2.54cm) cond Width Depth Height* In Out ondensate Water FPT Low Voltage Power Supply cm mm cm mm cm mm cm mm cm mm cm mm cm mm Horizontal Models Discharge onnection duct flange installed (±0.25 cm) eturn onnection using deluxe filter rack option (±0.25 cm) Unit Hanger Dimensions PV Size L M N P Q S T U (A) V (B) W ( ) X Supply Width Supply Depth eturn Depth eturn Height cm cm cm cm cm cm cm Horizontal units shipped with standard 2 (5.1 cm) (field adjustable to 1 (2.55 cm)) open application filter rack extending 2.2 (5.6 2/18/18 cm) from unit and is not suitable for duct connection, For ductable return connection applications, order the deluxe 2 (field adjustable to 1 ) duct collar/filter rack which extends 3.25 from the unit and is suitable for duct connections. ** UBH offers a lifted drain pan that allows the trap to be installed without additional ceiling height required. Horizontal Disconnect When using disconnect, do not use dimension K from the standard horizontal dimensional data. Use dimension KK from the horizontal disconnect dimensional data. Horizontal Models KK [20.32] 005 [20.8] [20.8] 009 [23.4] [23.4] 015 [28.4] 017 [25.9] Dimensions in [cm] Disconnect Located on this Side for a Left eturn 2.1 in. [5.3 cm] Disconnect Location KK Power Supply Horizontal Shown in ight eturn onfiguration 9

10 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Installing Horizontal Units Installing Horizontal Units Horizontal units are available with side or end discharge and may be easily field converted by flipping the blower discharge panel. Horizontal units are normally suspended from a ceiling by four 3/8 in. diameter threaded rods. The rods are usually attached to the unit by hanger bracket kits furnished with each unit. Lay out the threaded rods per the dimensions below. Assemble the hangers to the unit as shown. Securely tighten the brackets to the unit using the weld nuts located on the underside of the bottom panel. When attaching the hanger rods to the bracket, a double nut is required since vibration could loosen a single nut. NOTE: The unit should be pitched approximately 1/4 in. towards the drain in both directions to facilitate the removal of condensate. Use only the bolts provided in the kit to attach hanger brackets. The use of longer bolts could damage internal parts. Some applications require the installation of horizontal units on an attic floor. In this case, the unit should be set in a full size secondary drain pan on top of a vibration absorbing pad. The secondary drain pan prevents possible condensate overflow or water leakage damage to the ceiling. The secondary drain pan is usually placed on a plywood base isolated from the ceiling joists by additional layers of vibration absorbing material. Insulate supply plenum and use at least one 90 elbow and flexible duct collar to reduce noise. AUTION: Do not use rods smaller than 3/8 in. diameter since they may not be strong enough to support the unit. The rods must be securely anchored to the ceiling. Horizontal Unit Mounting 10

11 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Hanger Bracket Locations ight Left B D E ompressor Section Air Handler Section F E D ompressor Section Air Handler Section F A 3/8 Threaded od (not supplied) Vibration Isolator Washer Bolt and Lockwasher Hex Nuts (not supplied) Hanger Bracket Locations Model Hanger Kit Part Number A B in S500A04 cm in S500A04 cm in S500A04 cm in S500A04 cm in S500A04 cm in S500A04 cm in S500A04 cm /18/18 Weight Distribution Table Model Vertical Shipping Weight Horizontal Shipping Weight Horizontal Weight Distribution Front Back D E F lbs kg lbs kg lbs kg lbs kg lbs kg lbs kg lbs kg lbs kg lbs kg /18/

12 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Duct System An air outlet collar is provided on vertical top flow units and all horizontal units to facilitate a duct connection. A flexible connector is recommended for discharge and return air duct connections on metal duct systems. Uninsulated duct should be insulated with a minimum of 1-inch duct insulation. Application of the unit to uninsulated ductwork in an unconditioned space is not recommended as the unit s performance will be adversely affected. If the unit is connected to existing ductwork, check the duct system to ensure that it has the capacity to accommodate the air required for the unit application. If the duct is too small, as in the replacement of heating only systems, larger ductwork should be installed. All existing ductwork should be checked for leaks and repaired if necessary. The duct system should be sized to handle the design airflow quietly and efficiently. To maximize sound attenuation of the unit blower, the supply and return plenums should include an internal duct liner of fiberglass or constructed of ductboard for the first few feet. On systems employing a sheet metal duct system, canvas connectors should be used between the unit and the ductwork. If air noise or excessive airflow is a problem, the blower speed can be changed. Water Piping The proper water flow must be provided to each unit whenever the unit operates. To assure proper flow, use pressure/temperature ports to determine the flow rate. These ports should be located at the supply and return water connections on the unit. The proper flow rate cannot be accurately set without measuring the water pressure drop through the refrigerant-to-water heat exchanger. All source water connections on commercial units are fittings that accept a male pipe thread (MPT). Insert the connectors by hand, then tighten the fitting with a wrench to provide a leakproof joint. When connecting to an open loop (groundwater) system, thread any copper MPT fitting into the connector and tighten in the same manner as described above. 12

13 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Water Quality In ground water situations where scaling could be heavy or where biological growth such as iron bacteria will be present, a closed loop system is recommended. The heat exchanger coils in ground water systems may, over a period of time, lose heat exchange capabilities due to a buildup of mineral deposits inside. These can be cleaned, but only by a qualified service mechanic, as special solutions and pumping equipment are required. Hot water generator coils can likewise become scaled and possibly plugged. In areas with extremely hard water, the owner should be informed that the heat exchanger may require occasional flushing. Failure to adhere to the guidelines in the water quality table could result in loss of warranty. Units with cupronickel heat exchangers are recommended for open loop applications due to the increased resistance to build-up and corrosion, along with reduced wear caused by acid cleaning. Material opper 90/10 upronickel 316 Stainless Steel ph Acidity/Alkalinity Scaling alcium and (Total Hardness) (Total Hardness) (Total Hardness) Magnesium arbonate less than 350 ppm less than 350 ppm less than 350 ppm Hydrogen Sulfide Less than 0.5 ppm (rotten egg smell appears at 0.5 ppm) ppm Less than 1 ppm Sulfates Less than 125 ppm Less than 125 ppm Less than 200 ppm hlorine Less than 0.5 ppm Less than 0.5 ppm Less than 0.5 ppm hlorides Less than 20 ppm Less than 125 ppm Less than 300 ppm arbon Dioxide Less than 50 ppm ppm ppm orrosion Ammonia Less than 2 ppm Less than 2 ppm Less than 20 ppm Ammonia hloride Less than 0.5 ppm Less than 0.5 ppm Less than 0.5 ppm Ammonia Nitrate Less than 0.5 ppm Less than 0.5 ppm Less than 0.5 ppm Ammonia Hydroxide Less than 0.5 ppm Less than 0.5 ppm Less than 0.5 ppm Ammonia Sulfate Less than 0.5 ppm Less than 0.5 ppm Less than 0.5 ppm Total Dissolved Solids (TDS) Less than 1000 ppm ppm ppm LSI Index +0.5 to to to -0.5 Iron, FE 2 + (Ferrous) Iron Fouling Bacterial Iron Potential < 0.2 ppm < 0.2 ppm < 0.2 ppm (Biological rowth) Less than 1 ppm, above this Less than 1 ppm, above this Less than 1 ppm, above this Iron Oxide level deposition will occur level deposition will occur level deposition will occur Suspended Solids Erosion Threshold Velocity (Fresh Water) NOTES: rains = ppm divided by 17 mg/l is equivalent to ppm ondensate Drain Less than 10 ppm and filtered for max. of 600 micron size Less than 10 ppm and filtered for max. of 600 micron size Less than 10 ppm and filtered for max. of 600 micron size < 1.8 m/sec < 1.8 m/sec < 1.8 m/sec 2/22/12 On vertical units, the internal condensate drain assembly consists of a drain tube which is connected to the drain pan, a 3/4 in. PV female adapter and a flexible connecting hose. The female adapter may exit either the front or the side of the cabinet. The adapter should be glued to the field-installed PV condensate piping. On vertical units, a condensate hose is inside all cabinets as a trapping loop; therefore, an external trap is not necessary. Horizontal Drain onnection (omposite Drain Pan) On horizontal units, a PV stub or stainless steel tube is provided for condensate drain piping connection. An external trap is required (see below). If a vent is necessary, an open stand pipe may be applied to a tee in the fieldinstalled condensate piping. NOTE: All units equipped with electronic condensate overflow protection. Unit Pitch for Drain PV coupling Vent (if needed) PV tube stub 1/2'' (1.27 cm) Pitch PV tube stub 1.5 in (3.81 cm) 1.5 in. 1/8 in. (0.32 cm) per foot NOTE: UBH offers a lifted drain pan that allows the trap to be installed without additional ceiling height required. Drain 13

14 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL System leaning and Flushing leaning and Flushing Prior to start up of any heat pump, the water circulating system must be cleaned and flushed of all dirt and debris. If the system is equipped with water shutoff valves, the supply and return runouts must be connected together at each unit location (This will prevent the introduction of dirt into the unit, see Flushing with Water Shutoff Valve Equipped Systems illustration). The system should be filled at the water make-up connection with all air vents open. After filling, vents should be closed. Flushing with Water Shutoff Valve Equipped Systems eturn unout Supply unout ubber Hose unouts Initially onnected Together Mains The contractor should start the main circulator with the pressure reducing valve makeup open. Vents should be checked in sequence to bleed off any trapped air and to verify circulation through all components of the system. As water circulates through the system, the contractor should check and repair any leaks found in the piping system. Drain(s) at the lowest point(s) in the system should be opened for initial flush and blowdown, making sure water fill valves are set at the same rate. heck the pressure gauge at the pump suction and manually adjust the makeup water valve to hold the same positive pressure both before and after opening the drain valves. Flushing should continue for at least two hours, or longer if required, until drain water is clean and clear. The supplemental heater and/or circulator pump, if used, should be shut off. All drains and vents should be opened to completely drain the system. Short-circuited supply and return runouts should now be connected to the unit supply and return connections. efill the system with clean water. Test the system water for acidity and treat as required to leave the water slightly alkaline (ph 7.5 to 8.5). The specified percentage of antifreeze may also be added at this time. Use commercial grade antifreeze designed for HVA systems only. Environol brand antifreeze is recommended. Once the system has been filled with clean water and antifreeze (if used), precautions should be taken to protect the system from dirty water conditions. Dirty water will result in system-wide degradation of performance, and solids may clog valves, strainers, flow regulators, etc. Additionally, the heat exchanger may become clogged which reduces compressor service life and can cause premature unit failure. In boiler/tower application, set the loop control panel set points to desired temperatures. Supply power to all motors and start the circulating pumps. After full flow has been established through all components including the heat rejector (regardless of season), air vented and loop temperatures stabilized, each of the units will be ready for check, test and start up and for air and water balancing. round Source Loop System heckout Once piping is completed between the unit pumping system and ground loop, final purging and charging of the loop is needed. A high pressure pump is needed to achieve adequate flow velocity in the loop to purge air and dirt particles from the loop itself. Antifreeze solution is used in most areas to prevent freezing. Flush the system adequately to remove as much air as possible; then pressurize the loop to a static pressure of kpa (summer) or kpa (winter). This is normally adequate for good system operation. Loop static pressure may decrease soon after initial installation, due to pipe expansion and loop temperature change. unning the unit for at least 30 minutes after the system has been completely purged of air will allow for the break-in period. It may be necessary to adjust static loop pressure (by adding water) after the unit has run for the first time. Loop static pressure will also fluctuate with the seasons. Pressures will be higher in the winter months than during the cooling season. This fluctuation is normal and should be considered when charging the system initially. Ensure the pump provides adequate flow through the unit by checking pressure drop across the heat exchanger. Usually L/s of flow per ton of cooling capacity is recommended in earth loop applications. 14

15 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Open Loop round Water Systems Typical open loop piping is shown below. Always maintain water pressure in the heat exchanger by placing water control valves at the outlet of the unit to prevent mineral precipitation. Use a closed, bladder-type expansion tank to minimize mineral formation due to air exposure. Insure proper water flow through the unit by checking pressure drop across the heat exchanger and comparing it to the figures in unit capacity data tables in the specification catalog L/s of flow per ton of cooling capacity is recommended in open loop applications. Due to only minor differences in flow rate from low to high, only one solenoid valve should be used. The valve should be sized for full flow. Discharge water from the unit is not contaminated in any manner and can be disposed of in various ways, depending on local codes, i.e. recharge well, storm sewer, drain field, adjacent stream or pond, etc. Most local codes forbid the use of sanitary sewer for disposal. onsult your local building and zoning departments to assure compliance in your area. Open System - roundwater Application Unit Supply Aux. Heat Supply Flexible Duct ollar ubber Bladder Expansion Tank Drain Solenoid Valve Flow ontrol Valve (on outlet of Solenoid Valve) Water Out Water In Disconnects (IfApplicable) ompressor Line Voltage Low Voltage to Thermostat and Valve P/T Plugs Vibration Absorbing Pad Strainer Boiler Drains For HX Flushing Shut Off Valves Shut Off Valves (to isolate solenoid valve while acid flushing) 15

16 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Freeze Detection For Aurora Base ontrol, set SW2-1, FP1, on the printed circuit board for applications using a closed loop antifreeze solution to 15 F [-9.4 ]. On applications using an open loop/ground water system (or closed loop no antifreeze), set this dip switch to 30 F [-1.1 ], the factory default setting. (efer to the Dip Switch Field Selection table). Electrical onnections eneral Be sure the available power is the same voltage and phase as that shown on the unit serial plate. Line and low voltage wiring must be done in accordance with local codes or the National Electric ode, whichever is applicable. Power onnection onnect the incoming line voltage wires to L1 and L2 of the contactor for single-phase unit. onsult the Electrical Data tables for correct fuse sizes. 220 Volt Operation All Versatec ompact Series units are factory wired for 240 volt operation. For 220 volt operation, the red and blue transformer wires must be switched on terminal strip PS. AUTION: When installing a unit with a variable speed EM blower motor in 420/50/3 voltage, a neutral wire is required to allow Aurora Base ontrol Box 16

17 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Electrical Data 5-Speed EM Motor Model ated Voltage ompressor Blower Total Min Max Motor Unit irc Fuse/HA Voltage Min/Max M LA LA FLA FLA Amp Breaker /50/1 198/ /50/1 198/ /50/3 342/ / /50/1 198/ /50/3 342/ / /50/1 198/ /50/3 342/ / /50/3 342/ /50/1 198/ /50/3 342/ /50/3 342/ /50/3 342/ HA circuit breaker in USA only 8/18/18 17

18 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Electrical Data cont. Variable Speed EM Motor Model ated Voltage Voltage Min/Max ompressor M LA LA Blower Motor FLA Total Unit FLA Min irc Amp Max Fuse/HA Breaker /50/1 198/ / /50/1 198/ /50/1 198/ /50/1 198/ /50/3 342/ / /50/1 198/ /50/3 342/ / /50/1 198/ /50/3 342/ /50/3 342/ /50/1 198/ /50/3 342/ /50/3 342/ /50/3 342/ HA circuit breaker in USA only 8/18/18 aution: When installing a unit with a Variable Speed EM blower motor in /50/3 voltage, a neutral wire is required to allow proper unit operation. 18

19 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Blower Performance Data cont. 5-Speed EM Motor Model Motor Spd Motor Tap Blower Size Motor kw Airflow (L/s) at External Static Pressure High Med High Med x Med Low Low High Med High Med x Med Low Low High Med High Med x Med Low Low High Med High Med x Med Low Low High Med High Med x Med Low Low High Med High Med x Med Low Low High Med High Med x Med Low Low High Med High Med x Med Low Low Factory settings are in Bold 9/21/15 Air flow values are with dry coil and standard 2.5 cm filter 5-Speed EM Motor onnections High Voltage onnections 3/16 in. - Black L - Orange - reen L N N - Brown - Blue Y1 - ed Low Voltage onnections 1/4 in. AUX - ray 19

20 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL 5-Speed EM onstant Torque Motors The 5-speed EM is a onstant Torque EM motor and delivers air flow similar to a PS but operates as efficiently as an variable speed EM Motor. Because it s an EM Motor, the 5-speed EM can ramp slowly up or down like the variable speed EM Motor. There are 5 possible speed taps available on the 5-speed EM motor with #1 being the lowest airflow and #5 being the highest airflow. These speed selections are preset at the time of manufacture and are easily changed in the field if necessary. 5-Speed EM Benefits: - High efficiency - Soft start - 5 speeds with up to 4 speeds on-line - Built in logic allows air flow to change with, Y1, Y2 and W signals - Super efficient low airflow continuous blower setting () If more than one tap are energized at the same time, built in logic gives precedence to the highest tap number and allows air flow to change with, Y1, Y2 and W signals. Each of those 5 speeds has a specific Torque value programmed into the motor for each speed selection. As static pressure increases, airflow decreases resulting in less torque on the rotor. The motor responds only to changes in torque and adjusts its speed accordingly. The 5-speed EM motor is powered by line voltage but the motor speed is energized by 24VA. Signal onnection - 1/4 in. quick connects - ommon to, 24VA to Taps #1-5. Applying 24VA power between any of the motor taps 1-5 (1/4 in. quick connects) and common will signal the motor to run and regulate torque at the programmed level. The tap input voltage must be in the range 12-33VA. The 5-speed EM will have less variation over the operating static pressure range versus a PS motor as well as a significant watts reduction due to the high motor efficiency. Thermal Protection - Motor is electronically protected. Locked otor Amps - If motor speed decreases below a programmed stall speed, the motor will shut down and after a delay period, the control will attempt to restart the motor. The 5-speed EM speed tap selections are as follows: The blue wire should be placed on the speed tap desired for the () continuous blower setting factory wired to Tap 1. The red wire should be placed on the speed tap desired during compressor operation (Y1 signal) factory wired to Tap 3 or 4. The gray wire is not factory wired to the motor and is tied to the wire harness. It is field connected and can be used with 3ht/2cl thermostats or IntelliZone to deliver the required air flow for the Y2 signal. The tan wire should be placed on the speed tap desired for auxiliary heat (W signal) factory wired to Tap 5. 20

21 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Blower Performance Data cont. Variable Speed EM Motor Model Max ESP (Pa) Blower Size Motor kw x x Air Flow Dip Switch Settings L 189 L M 283 M 330 H H x L M H x L M H x L M H x L M H x L M H x L M H Factory settings are at recommended L-M-H DIP switch locations L/s is controlled within 5% up to the maximum ESP M-H settings MUST be located within boldface L/s range Max ESP includes allowance for wet coil and standard filter Lowest and Highest DIP switch settings are assumed to be L and H respectively 12/5/14 Variable Speed onstant Torque EM Fan Speed Fan PM Airflow [L/s] at External Static Pressure [Pa] Air flow values are with dry coil and standard 2.5 cm filter 2/18/2018 Setting Blower Speed - Variable Speed EM Variable speed EM blower motors have 12 selectable speeds and are factory set for optimum performance. When applicable, the speed settings may also be adjusted through the Building Automation System (BAS). AUTION: Disconnect all power before performing this operation. 21

22 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Blower Performance Data cont. Setting Blower Speed - Variable Speed EM The AB board s Yellow onfig LED will flash the current variable speed EM blower speed selections for low, med, and high continuously with a short pause in between. The speeds can also be confirmed with the AID Tool under the Setup/EM Setup screen. The variable speed EM blower motor speeds can be field adjusted with or without using an AID Tool. Variable Speed EM Setup with an AID Tool cont. EM SPEED INFO LOW SPEED: 3 MED SPEED: 5 HIH SPEED: 7 Selecting YES will enter variable speed EM speed setup, while selecting NO will return to the previous screen. Variable Speed EM Setup without an AID Tool The blower speeds for Low ( only), Med (Y1), and High (Y2/Aux) can be adjusted directly at the Aurora AB board which utilizes the push button (SW1) on the AB board. This procedure is outlined in the Variable Speed EM onfiguration Mode portion of the Aurora Base ontrol System section. Variable Speed EM Setup with an AID Tool A much easier method utilizes the AID Tool to change the airflow using the procedure below. First navigate to the Setup screen and then select EM Setup. This screen displays the current variable speed EM settings. It allows the technician to enter the setup screens to change the variable speed EM settings. hange the highlighted item using the and buttons and then press the button to select the item. WANT TO HANE? YES OPTION NO ENTE Variable Speed EM Speed Setup - These screens allow the technician to select the low, medium, and high blower speed for the variable speed EM blower motor. hange the highlighted item using the and buttons. Press the button to select the speed. EM SPEED INFO 1 2 < LOW EM SPEED INFO 1 2 LOW < MED EM SPEED INFO 1 2 LOW MED < HIH OPTION ENTE OPTION ENTE OPTION ENTE After the high speed setting is selected the AID Tool will automatically transfer back to the EM Setup screen. 22

23 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Wiring Schematics Aurora ontrol with UP To AB - P BAnet or N2 Network onnections Devices Must Be Wired in Daisy hain onfiguration Orange ed White Black Blue reen Brown Yellow Optional LON Add-On Module LON O NET+ NET- NET- OM NET+ OM NET+ NET- POWE ND 24 VA LON Network onnections OM NET+ LED1 TX LED2 X LED3 POWE FOMAT BATT Devices Must Be Wired in Daisy hain onfiguration 2 1 Service LED1 LED2 Tx LED3 x Net LED4 1 2 EHELON NET- N/ N/ Signal ND NET+ NET- +12V NET LED7 2W X 4W ND LN+ LN- +12 /S LON ADAPTE POT LED6 TX LOAL AESS LED4 LED5 UN E ON TEN S ONE S ommunication Options NOTE 1 MA Address Setting 1 2 ZS Sensor 1 Addr: 0 ND NET+ NET- +12V ZS Sensor 2 Addr: 1 ND NET+ NET- +12V ZS Sensor 3 Addr: 2 ND NET+ NET- +12V ZS Sensor Information Zone Sensors can be wired in daisy chain as show or in a star or hybrid configuration. Maximum of 5 sensors per UP. Maximum allowable load 210mA. See the UP install manual for possible sensor combinations. Notes 1. Use DIP Switches 5 8 to change communication protocol and DIP switches 1 2 to change BAnet baud rate DIP Switch Value ON Each ZS sensor must have a unique address, but the addresses do not need to be sequential. Use the DIP switches on the back of the ZS sensor to set an address from 0 to 4. (0 is the factory default.) Each DIP switch has the value shown in the figure to the left. Turn on as many DIP switches as you need so that their total value equals the address. Legend Factory Low Voltage Wiring Field Low Voltage Wiring J45 onnector Page 1 23

24 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Wiring Schematics cont. ommercial Aurora with Variable Speed EM Motor /50/1 ompressor S Blue ap Black ed Tan T2 T1 L2 L1 Note 1 reen (93) round Neutral Disconnect Unit Power Supply /50/1 Black (95) L1 L1 ed (97) L2 L2 Note 2 ed 220V Blue 240V Black L3 L3 Brown Orange reen Transformer P11 24V Yellow Black/White EM2 Fan Motor PWM FM P12 Note 3 Isolation Valve Dual apacity Units Only UltraTech S V V FD T 470 esistor 470 LP HP ed (51) reen (50) White (52) ed (53) Note 3 EH1 P2 ES LS ALM AL A OM A NO A N LO O/B Y1 Y2 W DH P1 2 F K5-Alarm elay K6-Acc elay P8 P9 om2 LED5 S485 NET JW2 Violet (14) om1 LED5 S485 NET - + P7 Black (15) F F 2 HI K4-Fan elay K2- elay P Blue(16) Blue(18) 2 LO K3-2 elay 2 S485 EXP P5 Aurora Base ontrol (AB) Orange (01) Orange (02) Yellow Yellow Blue (07) Blue (08) Black (09) Black (10) EV EV FP1 FP1 FP2 FP2 LPS LPS HPS HPS P4 K1-V elay SW1 Test Mode - + P6 O EH1 EH2 P3 Status LED3 Y1 F1-3A PWM FM Fault LED1 P13 Off On FP1 15 F/30 F 1 FP2 15 F/30 F 2 V B/O 3 Acc Dip 4 4 Acc Dip 5 5 Dual/Single 6 L Output Type 7 Future Use 8 SW2 onfig LED2 Y F Black/White Yellow Violet (42) Blue (24) Yellow (25) reen/yellow (28) reen Brown (23) ondensate 24

25 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Wiring Schematics cont. ommercial Aurora with Variable Speed EM Motor /50/1 Legend Factory Low Voltage Wiring Factory Line Voltage Wiring Field Low Voltage Wiring Field Line Voltage Wiring Optional Block D Voltage PB Traces Field Zone Sensor Wiring Internal Junction Quick onnect Terminal T Thermistor elay oil Switch - ondensate Overflow Switch - High pressure Switch - Low pressure L1 Field Wiring Lug Polarized connector round elay ontacts N.O., N.. Light Emitting Diode - reen apacitor Y Light Emitting Diode - Yellow Fuse ompressor ontactor O ondensate Overflow Sensor ES Emergency Shutdown HP High Pressure Switch LP Low Pressure Switch FD Freeze Detection Sensor F1 Fuse Light Emitting Diode - ed SW1 Push button SW2 DIP package 8 position B Blower elay V eversing Valve oil PM Phase uard Monitor H eheat Valve oil Aurora LED Flash odes Slow Flash Fast Flash Flash ode 1 second on and 1 second off 100 milliseconds on and 100 milliseconds off 100 milliseconds on and 400 milliseconds off with a 2 second pause before repeating andom Start Delay Status LED (LED1, reen) onfiguration LED (LED2, Yellow) Fault LED (LED3, ed) Status LED (LED1, reen) Fast Flash Fast Flash Fast Flash onfiguration LED (LED2, Yellow) Fault LED (LED3, ed) Normal Mode ON No Software Overide Flash EM Setting Normal Mode OFF ontrol is Non-Functional OFF DIP Switch Overide Slow Flash Input Fault Lockout Flash ode 1 Test Mode Slow Flash EM onfigure Mode Fast Flash High Pressure Lockout Flash ode 2 Lockout Active Dehumidification Mode eserved eserved Load Shed ESD eserved Fast Flash Flash ode 2 Flash ode 3 Flash ode 4 Flash ode 5 Flash ode 6 Flash ode 7 eset onfigure Mode Off Low Pressure Lockout Low Air oil Limit Lockout - FP2 Low Water oil Limit Lockout - FP1 eserved ondensate Overflow Lockout Over/Under Voltage Shutdown eserved eserved Air/Water oil Limit Sensor Error Flash ode 3 Flash ode 4 Flash ode 5 Flash ode 6 Flash ode 7 Flash ode 8 Flash ode 9 Flash ode 10 Flash ode 11 Notes: 1 Optional, factory installed unit mounted disconnect. 2 Swap blue and red leads for 220V operation. 3 Optional, factory installed internal isolation valve. Accessory elay Operation SW2-4 SW2-5 ycle with Blower On On ycle with ompressor Off Off Water Valve Slow Open On Off Outdoor Air Damper Off On Aurora Timing Events Event Normal Mode Test Mode andom Start Delay 5 to 80 seconds 1 second ompressor On Delay 5 seconds < 1 second ompressor Minimum On Time 2 minutes 5 seconds ompressor Short ycle Delay 4 minutes 15 seconds Blower Off Delay 30 seconds 2 seconds Fault ecognition Delay High Pressure Start-Up Bypass Low Pressure Less than 1 second 2 minutes Less than 1 second 30 seconds Fault ecognition Delay Low Pressure 30 seconds 30 seconds Start-Up Bypass Low Water/Air oil Limit Fault ecognition Delay Low Water/Air oil Limit Fault ecognition Delay ondensate Overflow 2 minutes 30 seconds 30 seconds 30 seconds 30 seconds 30 seconds Thermostat all ecognition Time 2 seconds 2 seconds Auxiliary Heat Staging Delay Emergency Heat Staging Delay 5 minutes 2 minutes 20 seconds 7.5 seconds Water Valve Slow Open Delay 90 seconds 90 seconds eheat Delay 30 seconds 30 seconds 2 2 F Y1 JW2 - Alarm HP HP LP LP FP2 FP2 FP1 FP1 EV EV LO HI F F P2 P4 Factory P5 Factory ES LS PWM FM EM PWM P13 SW1 Test V K1 K2 Hi K3 Fan K4 Alarm K5 Acc K6 Field onnections ALM AL A c A no A nc Off LED1 FP1 15 o F/30 o F FP2 15 o F/30 o F Fault V B/O A Dip 4 LED3 A Dip 5 Dual/Single L Pulse/ontinuous Status eheat/normal P9 LO P1 LO Factory Use P11 AUOA BASE ONTOL Factory Fan onnection O/B Field onnections O/B SW2 On 1 LED2 2 Y 3 onfig Y1 Y2 W Y1 Y2 W DH DH om1 om2 3A-Fuse P3 Factory P6 P7 S 485 P8 EH1 S485 Exp S485 NET EH2 EH1 O N/A (+) (-) (+) (-) 25 Page 1

26 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Wiring Schematics cont. ommercial Aurora with Variable Speed EM Motor /50/3 ompressor L3 T3 ed T3 T1 Note 3 T2 Yellow Black Phase uard Orange Monitor T2 T1 (PM) Note 1 L1 L2 L3 Brown PB3 reen (93) N ray (94) L2 L1 Black (54) L1 Black (95) L1 Black (7) White (8) Blue (55) L2 Yellow (96) L2 ed (9) round Neutral Disconnect Unit Power Supply /50/3 w/neutral L1 L2 Black (54) ed (56) L3 ed (97) L3 L3 Blue (55) ed (56) Note 4 NOTE 5 Blue Black 420V ed 380V Transformer reen Orange Brown PM Y-OUT Y Yellow 24V Black/White P11 Black/White (92) Yellow (91) EM2 Fan Motor Note 2 Isolation Valve Dual apacity Units Only UltraTech S V V FD T 470 esistor 470 LP HP PWM FM P ed (51) reen (50) White (52) ed (53) Note 2 EH1 P2 ES LS ALM AL A OM A NO A N LO O/B Y1 Y2 W DH P1 2 F K5-Alarm elay K6-Acc elay P8 P9 om2 LED5 S485 NET JW2 Violet (14) om1 LED5 S485 NET - + P7 Black (15) F F 2 HI K4-Fan elay K2- elay P Blue(16) Blue(18) 2 LO K3-2 elay 2 S485 EXP P5 Aurora Base ontrol (AB) Orange (01) Orange (02) Yellow Yellow Blue (07) Blue (08) Black (09) Black (10) EV EV FP1 FP1 FP2 FP2 LPS LPS HPS HPS P4 K1-V elay SW1 Test Mode - + P6 O EH1 EH2 P3 Status LED3 Y1 Fault LED1 F1-3A PWM FM P13 Off On FP1 15 F/30 F 1 FP2 15 F/30 F 2 V B/O 3 Acc Dip 4 4 Acc Dip 5 5 Dual/Single 6 L Output Type 7 Future Use 8 SW2 onfig LED2 Y F Black/White Yellow Violet (42) Blue (24) Yellow (25) reen/yellow (28) reen Brown (23) ondensate 26

27 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Wiring Schematics cont. ommercial Aurora with Variable Speed EM Motor /50/3 Accessory elay Operation SW2-4 SW2-5 ycle with Blower On On ycle with ompressor Off Off Water Valve Slow Open On Off Outdoor Air Damper Off On Aurora Timing Events Event Normal Mode Test Mode andom Start Delay 5 to 80 seconds 1 second ompressor On Delay 5 seconds < 1 second ompressor Minimum On Time 2 minutes 5 seconds ompressor Short ycle Delay 4 minutes 15 seconds Blower Off Delay 30 seconds 2 seconds Fault ecognition Delay High Pressure Start-Up Bypass Low Pressure Less than 1 second 2 minutes Less than 1 second 30 seconds Fault ecognition Delay Low Pressure 30 seconds 30 seconds Start-Up Bypass Low Water/Air oil Limit Fault ecognition Delay Low Water/Air oil Limit Fault ecognition Delay ondensate Overflow 2 minutes 30 seconds 30 seconds 30 seconds 30 seconds 30 seconds Thermostat all ecognition Time 2 seconds 2 seconds Auxiliary Heat Staging Delay Emergency Heat Staging Delay 5 minutes 2 minutes 20 seconds 7.5 seconds Water Valve Slow Open Delay 90 seconds 90 seconds eheat Delay 30 seconds 30 seconds Aurora LED Flash odes Slow Flash Fast Flash Flash ode 1 second on and 1 second off 100 milliseconds on and 100 milliseconds off 100 milliseconds on and 400 milliseconds off with a 2 second pause before repeating andom Start Delay Status LED (LED1, reen) onfiguration LED (LED2, Yellow) Fault LED (LED3, ed) Status LED (LED1, reen) Fast Flash Fast Flash Fast Flash onfiguration LED (LED2, Yellow) Fault LED (LED3, ed) Normal Mode ON No Software Overide Flash EM Setting Normal Mode OFF ontrol is Non-Functional OFF DIP Switch Overide Slow Flash Input Fault Lockout Flash ode 1 Test Mode Slow Flash EM onfigure Mode Fast Flash High Pressure Lockout Flash ode 2 Lockout Active Dehumidification Mode eserved eserved Load Shed ESD eserved Fast Flash Flash ode 2 Flash ode 3 Flash ode 4 Flash ode 5 Flash ode 6 Flash ode 7 eset onfigure Mode Off Low Pressure Lockout Low Air oil Limit Lockout - FP2 Low Water oil Limit Lockout - FP1 eserved ondensate Overflow Lockout Over/Under Voltage Shutdown eserved eserved Air/Water oil Limit Sensor Error Flash ode 3 Flash ode 4 Flash ode 5 Flash ode 6 Flash ode 7 Flash ode 8 Flash ode 9 Flash ode 10 Flash ode 11 L1 Notes: 1 Optional, factory installed unit mounted disconnect. 2 Optional, factory installed internal isolation valve. 3 Optional, factory installed phase guard 4 Optional, factory installed phase guard. The yellow transformer wire shall be connected directly to the PU board, if this option is not installed. 5 Switch Blue and ed transformer wires for 380V Operation Factory Low Voltage Wiring Factory Line Voltage Wiring Field Low Voltage Wiring Field Line Voltage Wiring Optional Block D Voltage PB Traces Field Zone Sensor Wiring Internal Junction Quick onnect Terminal Field Wiring Lug round elay ontacts N.O., N.. apacitor Fuse ompressor ontactor O ondensate Overflow Sensor ES Emergency Shutdown HP High Pressure Switch LP Low Pressure Switch FD Freeze Detection Sensor F1 Fuse Legend 3 T 2 Y 1 Thermistor elay oil Switch - ondensate Overflow Switch - High pressure Switch - Low pressure Polarized connector Light Emitting Diode - reen Light Emitting Diode - Yellow Light Emitting Diode - ed SW1 Push button SW2 DIP package 8 position B Blower elay V eversing Valve oil PM Phase uard Monitor H eheat Valve oil 2 2 F Y1 JW2 - Alarm HP HP LP LP FP2 FP2 FP1 FP1 EV EV LO HI F F P2 P4 Factory P5 Factory ES LS PWM FM EM PWM P13 SW1 Test V K1 K2 Hi K3 Fan K4 Alarm K5 Acc K6 Field onnections ALM AL A c A no A nc Off LED1 FP1 15 o F/30 o F FP2 15 o F/30 o F Fault V B/O A Dip 4 LED3 A Dip 5 Dual/Single L Pulse/ontinuous Status eheat/normal P9 LO P1 LO Factory Use P11 AUOA BASE ONTOL Factory Fan onnection O/B Field onnections O/B SW2 On 1 LED2 2 Y 3 onfig Y1 Y2 W Y1 Y2 W DH DH om1 om2 3A-Fuse P3 Factory P6 P7 S 485 P8 EH1 S485 Exp S485 NET EH2 EH1 O N/A (+) (-) (+) (-) Page 27

28 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL Wiring Schematics cont. ommercial Aurora with Variable Speed EM Motor /50/1 ompressor S Blue ap Black ed Tan T2 T1 Unit Power Supply /50/1 L2 L1 reen (93) round Neutral Disconnect Black (95) L1 L1 ed (97) L2 L2 ed 220V Blue 240V Black L3 L3 Black ed lass 2 Transfo rmer 24V Yellow Black/White EM Fan Motor Dual apacity Units Only Ultra Tech V 470 esistor FP LP HP S 470 T V ed (51) reen (50) White (52) ed (53) Note 3 P2 ES LS ALM AL A OM A NO A N LO P1 O/B Y1 Y2 W DH EH1 2 F K5-Alarm elay K6-Acc elay P8 P9 om2 LED5 S485 NET JW2 Violet (14) om1 LED5 S485 NET - + P7 Black (15) F F 2 HI K4-Fan elay K2- el ay P Blue(16) Blue(18) 2 LO K3-2 elay 2 S485 EXP P5 Aurora Base ontrol (AB) Orange (01) Orange (02) Yellow Yellow Blue (07) Blue (08) Black (09) Black (10) EVEVFP1 FP1 FP2 FP2 LPS LPSHPSHPSP4 K1-V elay SW1 Test Mode - + P6 O EH1 EH2 P3 Status LED3 Y1 F1-3A PWM FM Faul t LED1 P13 Off On FP1 15 F/30 F 1 FP2 15 F/30 F 2 V B/O 3 Acc Dip 4 4 Acc Dip 5 5 Dual/Single 6 L Output Type 7 eheat/normal 8 SW2 onfig LED2 Y F Black/White Yellow Yellow Blue reen Brown (23) ondensate ray (61) H ray (60) Note 4 28

29 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL Wiring Schematics cont. ommercial Aurora with Variable Speed EM Motor /50/1 Notes: 1 Optional, factory installed unit mounted disconnect. 2 Swap blue and red leads for 220V operation. 3 Optional, factory installed internal isolation valve. 4 Optional, fac tory installed r eheat. Factory Low Voltage Wiring Factory Line Voltage Wiring Field Low Voltage Wiring Fi eld Li ne Voltage Wi ri ng Optional Block D Voltage PB Traces Fi eld Zone Sensor Wi ri ng Internal Junction Qui ck on nect Terminal Legend T Thermistor elay oil Switch - ondensate Overflow Switch - High pressure Switch - Low pressure L1 Fi eld Wiring Lug Polarized connector round elay ontacts N.O., N.. Light Emitting Diode - reen apacitor Y Light Emitting Diode - Yellow Fuse ompressor ontactor O ondensate Overflow Sensor ES Emergency Shutdown HP High Pressure Switch LP Low Pressure Switch FP Freeze Protection F1 Fuse Light Emitting Diode - ed SW1 Push button SW2 DIP package 8 position B Blower elay V eversing Valve oil PM Phase uard Monitor H eheat Valve oi l Aurora LED Flash odes Slow Flash Fast Flash Flash ode 1 second on and 1 second off 100 milliseconds on and 100 milliseconds off 100 milliseconds on and 400 milliseconds off with a 2 second pause before repeating andom Start Delay Status LED (LED1, reen) onfiguration LED (LED2, Yellow) Fault LED (LED3, ed) Status LED (LED1, reen) Fast Fl ash Fast Fl ash Fast Fl ash onfiguration LED (LED2, Yellow) Fault LED (LED3, ed) Normal Mode ON No Software Overide Flash EM Setting Normal Mode OFF ontrol is Non-Functional OFF DIP Switch Overide Slow Flash Input Fault Lockout Flash ode 1 Test Mode Slow Flash EM onfigure Mode Fast Flash High Pressure Lockout Flash ode 2 Lockout Active Dehumidification Mode eserved eserved Load Shed ESD eserved Fast Fl ash Flash ode 2 Flash ode 3 Flash ode 4 Flash ode 5 Flash ode 6 Flash ode 7 eset onfigure Mode Off Low Pressure Lockout Low Air oil Limit Lockout - FP2 Low Water oil Limit Lockout - FP1 eserved ondensate Overflow Lockout Over/Under Voltage Shutdown eserved eserved Air/Water oil Limit Sensor Error Flash ode 3 Flash ode 4 Flash ode 5 Flash ode 6 Flash ode 7 Flash ode 8 Flash ode 9 Flash ode 10 Flash ode 11 Accessor y elay Operation SW2-4 SW2-5 ycle with Blower On On ycle with ompressor Off Off Water Valve Slow Open On Off Outdoor Air Damper Off On Aurora Timing Events Event Normal Mode Test Mode andom Start Delay 5 to 80 seconds 1 second ompressor On Delay 5 seconds < 1 second ompressor Minimum On Time 2 minutes 5 seconds ompressor Short ycle Delay 4 minutes 15 seconds Blower Off Delay 30 seconds 2 seconds Fault ecognition Delay High Pressure Less than 1 second Less than 1 second Start-Up Bypass Low Pressure 2 minutes 30 seconds Fault ecognition Delay Low Pressure 30 seconds 30 seconds Start-Up Bypass Low Water/Air oil Limit Fault ecognition Delay Low Water/Air oil Limit Fault ecognition Delay ondensate Overflow 2 minutes 30 seconds 30 seconds 30 seconds 30 seconds 30 seconds Thermostat all ecognition Time 2 seconds 2 seconds Auxiliary Heat Staging Delay Emergency Heat Stagi ng Dela y 5 minutes 2 minutes 20 seconds 7.5 seconds Water Valve Slow Open Delay 90 seconds 90 seconds eheat Delay 30 seconds 30 seconds 2 2 F Y1 JW2 - Alarm HP HP LP LP FP2 FP2 FP1 FP1 EV EV LO HI F F 29 P2 ES P4 Factory P5 Factory LS PWM FM EM PWM P13 ALM AL A c SW1 Test V K1 K2 Hi K3 Fan K4 Alarm K5 Acc K6 Fi eld onnections A no A nc P9 LO P1 LO LED1 P11 Off FP1 15 o F/30 o F FP2 15 o F/30 o F Faul t V B/O A Dip 4 LED3 A Dip 5 Dual/Single L Pulse/ontinuous Status eheat/normal Factory Use AUOA BASE ONTOL Factory Fan onnection O/B O/B Y1 Y1 Y2 Fi eld onnections Y2 SW2 W W On 1 LED DH DH Y onfig om1 om2 3A-Fuse P3 Factory P6 S 485 EH1 S485 Exp P7 P8 S485 NET EH2 EH1 O N/A (+) (-) Page 1

30 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL ontrols - Aurora Base ontrol Aurora Base ontrol Field Selectable Options via Hardware DIP Switch (SW1) Test/onfiguration Button (See SW1 Operation Table) NOTE: efer to the Aurora Base ontrol Application and Troubleshooting uide and the Instruction uide: Aurora Interface and Diagnostics (AID) Tool for additional information. ontrol Features Software AB Standard Version 3.0 Single or Dual apacity ompressors Either single or dual capacity compressors can be operated. Variable Speed EM Blower Motor Option (If Applicable) A Variable Speed EM blower motor can be driven directly using the onboard PWM output. Four blower speeds are available based upon the, Y1, Y2, and W input signals to the board. The blower speeds can be changed either by the EM manual configurations mode method or by using the Aurora AID Tool directly. All four blower speeds can be set to the same speed if desired. 5-Speed EM Blower Motor Option (If Applicable) A 5-Speed EM blower motor will be driven directly using the thermostat connections. Any of the, Y1, or Y2/W signals can drive any of the 5 available pre-programmed blower speeds on the motor. All 5 Series "" vintage units will be wired this way at the factory. Other ontrol Features andom start at power up Anti-short cycle protection High and low pressure cutouts Loss of charge Water coil freeze detection Air coil freeze detection Over/under voltage protection ondensate overflow sensor Load shed Dehumidification (where applicable) Emergency shutdown Hot gas reheat operation (where applicable) Diagnostic LED Test mode push button switch Two auxiliary electric heat outputs Alarm output Accessory output with N.O. and N.. Two Modbus communication Ports 30 Test Mode The control is placed in the test mode by holding the push button switch SW1 for 2-5 seconds. In test mode most of the control timings will be shortened by a factor of sixteen (16). LED3 (green) will flash at 1 second on and 1 second off. Additionally, when entering test mode LED1 (red) will flash the last lockout one time. Test mode will automatically time out after 30 minutes. Test mode can be exited by pressing and holding the SW1 button for 2 to 5 seconds or by cycling the power. NOTE: Test mode will automatically be exited after 30 minutes. Variable Speed EM onfiguration Mode (If Applicable) The control is placed in the EM configuration mode by holding the pushbutton switch SW1 for 5 to 10 seconds, the high, low, and EM speeds can be selected by following the LED display lights. LED2 (yellow) will fast flash when entering the EM configuration. When setting speed LED3 (green) will be continuously lit, for low speed LED1 (red) will be continuously lit, and for high speed both LED3 (green) and LED1 (red) will be continuously lit. During the EM configuration mode LED2 (yellow) will flash each of the 12 possible blower speeds 3 times. When the desired speed is flashed press SW1, LED2 will fast flash until SW1 is released. speed has now been selected. Next select low speed, and high speed blower selections following the same process above. After third selection has been made, the control will exit the EM configuration mode. Aux fan speed will remain at default or current setting and requires the AID Tool for adjustment. eset onfiguration Mode The control is placed in reset configuration mode by holding the push button switch SW1 for 50 to 60 seconds. This will reset all configuration settings and the EEPOM back to the factory default settings. LED3 (green) will turn off when entering reset configuration mode. Once LED3 (green) turns off, release SW1 and the control will reset. DIP Switch (SW2) SW2-1 FP1 Selection Low water coil temperature limit setting for freeze detection. On = 30 F; Off = 15 F. SW2-2 FP2 Selection On = 30 F; Off = N/A SW2-3 V O/B - thermostat type. Heat pump thermostats with O output in cooling or B output in Heating can be selected. On = O; Off = B. SW2-4 Access elay Operation (P2) and 2-5 Access elay Operation SW2-4 SW2-5 ycle with Blower ON ON ycle with ompressor OFF OFF Water Valve Slow Opening ON OFF ycle with omm. T-stat Hum md OFF ON

31 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL ontrols - Aurora Base ontrol cont. ycle with Blower - The accessory relay will cycle with the blower output. ycle with ompressor - The accessory relay will cycle with the compressor output. Water Valve Slow Opening - The accessory relay will cycle and delay both the blower and compressor output for 90 seconds. SW2-6 Operation selection of single or dual capacity compressor. On = Single Stage; Off = Dual apacity SW2-7 Lockout and Alarm Outputs (P2) selection of a continuous or pulsed output for both the LO and ALM Outputs. On = ontinuous; Off = Pulsed SW2-8 Future Use Alarm Jumper lip Selection From the factory, ALM is connected to 24 VA via JW2. By cutting JW2, ALM becomes a dry contact connected to AL. Variable Speed EM Blower Speeds The blower speeds can be changed either by using the EM manual configurations mode method or by using the Aurora AID Tool directly (see Instruction uide: Aurora Interface and Diagnostics (AID) Tool topic). Field Selectable Options via Software (Selectable via the Aurora AID Tool) EM Blower Speeds An EM blower motor can be driven directly using the onboard PWM output. Four blower speeds are available, based upon the, Y1 (low), Y2 (high), and Aux input signals to the board. The blower speeds can be changed either by the EM manual configurations mode method (see EM onfiguration Mode topic) or by using the Aurora AID Tool directly. All four blower speeds can be set to the same speed if desired. Aux blower speed will remain at default or current setting and requires the AID Tool for adjustment. Safety Features The following safety features are provided to protect the compressor, heat exchangers, wiring and other components from damage caused by operation outside of design conditions. Fuse a 3 amp automotive type plug-in fuse provides protection against short circuit or overload conditions. Anti-Short ycle Protection 4 minute anti-short cycle protection for the compressor. andom Start 5 to 80 second random start upon power up. Fault etry in the fault condition, the control will stage off the outputs and then try again to satisfy the thermostat Y input call. Once the thermostat input calls are satisfied, the control will continue on as if no fault occurred. If 3 consecutive faults occur without satisfying the thermostat Y input call, then the control will go to Lockout mode. Lockout when locked out, the blower will operate continuously in speed, and PS blower motor output will remain on. The Alarm output (ALM) and Lockout output (L) will be turned on. The fault type identification display LED1 (ed) shall flash the fault code. To reset lockout conditions with SW2-8 On, thermostat inputs Y1, Y2, and W must be removed for at least 3 seconds. To reset lockout conditions with SW2-8 Off, thermostat inputs Y1, Y2, W, and DH must be removed for at least 3 seconds. Lockout may also be reset by turning power off for at least 30 seconds or by enabling the emergency shutdown input for at least 3 seconds. Lockout With Emergency Heat - if the control is locked out in the heating mode, and a Y2 or W input is received, the control will operate in the emergency heat mode while the compressor is locked out. The first emergency heat output will be energized 10 seconds after the W input is received, and the blower will shift to high speed. If the control remains locked out, and the W input is present, additional stage of emergency heat will stage on after 2 minutes. When the W input is removed, all of the emergency heat outputs will turn off, and the EM blower will shift to speed and PS blower motor output will remain on. High Pressure fault is recognized when the Normally losed High Pressure Switch, P4-9/10 opens, no matter how momentarily. The High Pressure Switch is electrically in series with the ompressor ontactor and serves as a hardwired limit switch if an overpressure condition should occur. Low Pressure - fault is recognized when the Normally losed Low Pressure Switch, P4-7/8 is continuously open for 30 seconds. losure of the LPS any time during the 30 second recognition time restarts the 30 second continuous open requirement. A continuously open LPS shall not be recognized during the 2 minute startup bypass time. Loss of harge fault is recognized when the Normally losed Low Pressure Switch, P4-7/8 is open prior to the compressor starting. ondensate Overflow - fault is recognized when the impedance between this line and 24 VA common or chassis ground drops below 100K ohms for 30 seconds continuously. Freeze Detection (oax) - set points shall be either 30 F or 15 F. When the thermistor temperature drops below the selected set point, the control shall begin counting down the 30 seconds delay. If the thermistor value rises above the selected set point, then the count should reset. The resistance value must remain below the selected set point for the entire length of the appropriate delay to be recognized as a fault. This fault will be ignored for the initial 2 minutes of the compressor run time. Freeze Detection (Air oil) - uses the FP2 input to protect against ice formation on the air coil. The FP2 input will operate exactly like FP1 except that the set point is 30 degrees and is not field adjustable. 31

32 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL ontrols - Aurora Base ontrol cont. Over/Under Voltage Shutdown - An over/under voltage condition exists when the control voltage is outside the range of 18 VA to 30 VA. If the over/under voltage shutdown lasts for 15 minutes, the lockout and alarm relay will be energized. Over/under voltage shutdown is selfresetting in that if the voltage comes back within range of 18 VA to 30 VA for at least 0.5 seconds, then normal operation is restored. Operation Description Power Up - The unit will not operate until all the inputs and safety controls are checked for normal conditions. The unit has a 5 to 80 second random start delay at power up. Then the compressor has a 4 minute anti-short cycle delay after the random start delay. Standby In standby mode, Y1, Y2, W, DH, and are not active. Input O may be active. The blower and compressor will be off. Heating Operation Single ompressor Heating, 2nd Stage (Y1, Y2) The compressor will be staged to full capacity 20 seconds after Y2 input is received. The EM blower will shift to high speed seconds after the Y2 input is received. Dual ompressor Heating, 2nd Stage (Y1, Y2) In dual compressor operation, two AB boards used in 24 VA operation, there will be a Y2 call to the Y1 input on the second AB. The compressor will stage to full capacity 30 seconds after Y1 input is received to the second board. Single ompressor Heating, 3rd Stage (Y1, Y2, W) The hot water pump is de-energized and the first stage of electric heat is energized 10 seconds after the W command is received. If the demand continues the second stage of electric heat will be energized after 5 minutes. Dual ompressor Heating, 3rd Stage (Y1, Y2, W) - The first stage of electric heat is energized 10 seconds after the W command is received. If the demand continues the second stage of electric heat will be energized after 5 minutes Emergency Heat (W) - The blower will be started on speed, 10 seconds later the first stage of electric heat will be turned on. 5 seconds after the first stage of electric heat is energized the blower will shift to Aux speed. If the emergency heat demand is not satisfied after 2 minutes the second electric heat stage will be energized. ooling Operation In all cooling operations, the reversing valve directly tracks the O input. Thus, anytime the O input is present, the reversing valve will be energized. Single ompressor ooling, 2nd Stage (Y1, Y2, 0) The compressor will be staged to full capacity 20 seconds after Y2 input was received. The EM blower will shift to high speed 15 seconds after the Y2 input was received. Dual ompressor ooling, 2nd Stage (Y1, Y2, O) In dual compressor operation, two AB boards used in 24 VA operation, there will be a Y2 call to the Y1 input on the second AB. The compressor will stage to full capacity 30 seconds after Y1 input is received to the second board. Blower () - The blower will start immediately upon receiving a thermostat command. If there are no other commands from the thermostat the EM will run on speed until the command is removed. egardless of blower input () from the thermostat, the blower will remain on for 30 seconds at the end of each heating, cooling, and emergency heat cycle. Dehumidification (Y1, O, DH or Y1, Y2, O, DH) - When a DH command is received from the thermostat during a compressor call for cooling the EM blower speed will be reduced by 15% to increase dehumidification. Emergency Shutdown - Four (4) seconds after a valid ES input, P2-7 is present, all control outputs will be turned off and remain off until the emergency shutdown input is no longer present. The first time that the compressor is started after the control exits the emergency shutdown mode, there will be an anti-short cycle delay followed by a random start delay. Input must be tied to common to activate. ontinuous Blower Operation - The blower output will be energized any time the control has a input present, unless the control has an emergency shutdown input present. The blower output will be turned off when input is removed. Load Shed - The LS input disables all outputs with the exception of the blower output. When the LS input has been cleared, the anti-short cycle timer and random start timer will be initiated. Input must be tied to common to activate. Blower () - The blower will start immediately upon receiving a thermostat command. If there are no other commands from the thermostat the EM will run on speed until the command is removed. egardless of blower input () from the thermostat, the blower will remain on for 30 seconds at the end of each heating cycle. 32

33 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL ontrols - Aurora Base ontrol cont. Aurora Base ontrol LED Displays These three LEDs display the status, configuration, and fault codes for the control. These can also be read in plain English via the Aurora AID Tool. Status LED (LED3, reen) Description of Operation Fault LED, reen Normal Mode ON ontrol is Non-functional OFF Test Mode Slow Flash Lockout Active Fast Flash Dehumidification Mode Flash ode 2 (Future Use) Flash ode 3 (Future Use) Flash ode 4 Load Shed Flash ode 5 ESD Flash ode 6 (Future Use) Flash ode 7 onfiguration LED (LED2, Yellow) Description of Operation No Software Overwritten DIP Switch was Overwritten EM onfiguration Mode Fault LED (LED1, ed) ed Fault LED onfiguration LED, Yellow Flashing EM Setting Slow Flash Fast Flash LED Flash ode* Lockout eset/ emove Normal - No Faults OFF Fault - Input 1 No Auto Fault - High Pressure 2 Yes Hard or Soft Fault - Low Pressure 3 Yes Hard or Soft Fault - Freeze Detection FP2 4 Yes Hard or Soft Fault - Freeze Detection FP1 5 Yes Hard or Soft Fault - ondensate Overflow 7 Yes Hard or Soft Fault - Over/Under Voltage 8 No Auto Fault - FP1 & FP2 Sensor Error 11 Yes Hard or Soft NOTE: All codes >11 use long flash for tens digit and short flash for the ones digit. 20, 30, 40, 50, etc. are skipped. AB Basic Faults Aurora Interface and Diagnostics (AID) Tool The Aurora Interface and Diagnostics (AID) Tool is a device that is a member of the Aurora network. The AID Tool is used to troubleshoot equipment which uses the Aurora control via Modbus TU communication. The AID Tool provides diagnostics, fault management, EM setup, and system configuration capabilities to the Aurora family of controls. An AID Tool is recommended, although not required, for EM airflow settings. The AID Tool simply plugs into the exterior of the cabinet in the AID Tool port. AB ontrol Board Layout 2 2 F Y1 JW2 - Alarm HP HP LP LP FP2 FP2 FP1 FP1 EV EV LO HI F F Factory Factory P2 P4 P5 PWM FM EM PWM P13 SW1 Test V K1 K2 Hi K3 Fan K4 Alarm K5 Acc K6 Fi eld onnections Faul t LED3 A Dip 5 Dual/Single L Pulse/ontinuous Status eheat/normal P9 LO P1 LED1 Factory Use P11 AUOA BASE ONTOL Off FP1 15 o F/30 o F FP2 15 o F/30 o F V B/O A Dip 4 Factory Fan onnection O/B Y1 Y2 Fi eld onnections 8 SW2 W On 1 LED2 2 Y 3 onfig DH om1 om2 3A-Fuse P3 Factory P6 S485 Exp P7 S 485 P8 S485 NET EH1 EH2 EH1 O N/A (+) (-) ES LS ALM AL A c A no A nc LO O/B Y1 Y2 W DH 33

34 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL ontrols - UP DD ontrol (optional) Aurora UP ontroller ZS Series Sensors The Aurora Unitary Protocol onverter (UP) is designed to add-on to any Aurora based heat pump control. The Aurora Unitary Protocol onvertor (UP) is designed to allow water source heat pumps to be integrated into Building Automation Systems (BAS) with ease. The Aurora UP is an integrated solution and communicates directly with the Aurora Heat Pump ontrols and allows access/control of a variety of internal Aurora heat pump operations such as sensors, relay operation, faults and other information. In turn, the UP then converts internal Aurora Modbus protocol to BAnet MS/TP, LON, or N2 protocols and communicates to the BAS system. This provides the great benefit of complete control integration and a myriad of information available to the BAS from the heat pump control. Plus it also allows individual unit configuration such as EM fan speeds or freeze protection setting directly over the BAS without the need for access to the actual heat pump. The Aurora UP is programmed using the powerful Eikon object oriented. The Aurora UP is implemented with the Aurora Base ontroller (AB) heat pump control into our latest water source heat pumps. This will allow for a BAS to integrate and communicate to the heat pump thru a choice of 3 different communication protocols. The Aurora UP has the ability to communicate BAnet MS/TP, N2 open, or LonWorks (requires LON Plugin card). This flexibility is possible due to the onboard dipswitches which allow for the desired protocol and baud rate to be selected in the field. All zone temperatures and zone sensors are connected to the UP on an Net bus, simplifying hook up at the unit. Net sensors can include a combination of zone temperature and humidity, O2, and VO sensors. The UP includes built-in support for a custom configurable keypad/display unit - BAview6 (4-line by 40 character per line display) or BAview5 (2-line by 16 character per line display). Up to 2 Keypad/display units can be mounted remotely for configuration and troubleshooting. There are an extensive number of points that the UP has available over the network for integration into the BAS. ontrol programmers need to carefully determine which points they want to add into the BAS database. A list of the BAnet points, N2 points, and LON SNVTs are available along with their individual point descriptions by contacting the ommercial Solutions roup at

35 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL ontrols - UP DD ontrol (optional) cont. N2 Modbus BAS BAnet LonWorks net Aurora UP Features ugged enclosure made of E 2950 ycoloy plastic Built-in surge transient protection circuitry Operating range of -29 to 60 ; 10 to 95% relative humidity, non-condensing Onboard 123A battery has a life of 10 years with 720 hours of cumulative power outage Multi-Protocol field selectable communication port that supports: EIA-485 BAnet 9600, 19.2k, 38.4k, 76.8k baud Metasys N2 Open LonWorks TP/FT-10 (equires optional LON plug-in communication card) Status of all unit operating conditions and fault lockouts Visual LED s for status of power, network communication, processor operation, and errors Provides gateway into Aurora heat pump controls for unsurpassed control flexibility Network point for commanding unit into load shed Network point for commanding unit into emergency shutdown Network points to assist in fan speed selection Network points for freeze protection settings Heating and cooling control from a remotely located zone sensor net communication port which allows for multiple net zone sensors (5) to be connected for space temperature averaging if desired. Local laptop or BAview connection for field service F, UL and E listed. BTL ertification is pending Aurora UP Optional Features BAview handheld display, needed for field configuration of fan speeds, set points, etc. AID Tool for Aurora AB configuration and troubleshooting. Aurora Advanced ontrol adds the Aurora AXB expansion board and provides added I/O and standard features Optional Sensor Kits (requires Aurora Advanced ontrol with AXB - Future Availability on Select Models/onfigurations) efrigeration Monitoring provides Suction and discharge pressure, Suction, liquid line temps and superheat and subcooling. Performance Monitoring provides entering and leaving loop water temperatures, loop flow rate as well as heat of extraction or rejection rate into the loop. Energy Monitoring provides real-time power measurement (Watt) of compressor, fan, auxiliary heat and zone pump. raphics packages available in the future 35

36 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL ontrols - UP DD ontrol (optional) cont. Port 1a is used to communicate to the Building Automation System (BAS). This port s settings are configured through the onboard dip switches. Port 2 is used to communicate to the Aurora Base ontroller (AB). Port 1b is used for the LonWorks plugin. 24Vac Dip switches for configuring the communication port protocol and baud rate for the BAS port. net port is used for communicating zone sensors. Mac address is set by 2 rotary dials. BAview or local laptop connection. Aurora Touch Interface Utilizing a touch-screen interface, the UP provides a technician the ability to configure and diagnose equipment at the unit or from any room sensor for added accessibility and simpler troubleshooting. The technician will have full access to equipment status, parameter values, temperature, and humidity sensing as well as access to alarm and trend history. With website-like navigation, the Aurora Touch Interface is easy to use and provides important insight into the system so your building can operate as efficiently as possible. Aurora UP Smart Tablet Option A smart tablet option is also available. Purchase a smart tablet accessory cable from WaterFurnace and download the OEMtrl App and connect to the unit either at the unit itself or via the zone sensor. This means connecting to the unit to adjust fan speeds, check on fault etc. as easily as walking up to the zone sensor without the need for accessing ceiling tiles or a stepladder. 36

37 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL ontrols - UP DD ontrol (optional) cont. 1. Leaving Air Temperature (LAT) Sensor This 10 kohm NT sensor is factory installed on all UP equipped heat pumps. It typically is attached to wiring inside the blower cabinet on the suction side of the blower. This sensor is attached on AB FP2 pins available as LAT AU ompressor Proving Sensors This optional factory installed current sensor is connected to confirm compressor operation via the power wires. The sensor is attached at AB Y1 and available at point BV Valve End Switch This optional input is setup for a field installed flow valve end switch. This end switch input is attached at AB Y2 and available at point BV Fan Proving Sensors This optional factory installed current sensor is connected to confirm fan operation via the power wires. The sensor is attached at AB and available at point BV Occupancy Sensor - This standard feature includes a field installed and wired room sensor with occupancy sensor typically found in DD systems. The Net room sensors can be found thru your commercial representative. The occupancy Sensors are attached at AB 0 and can be found at point BV Dirty Filter Switch This optional field installed switch is connected to confirm dirty filter operation. The dirty filter switch can be found thru your commercial representative. The sensor is attached at AB W and available at point BV Fault, onfiguration, and Status odes The codes can be visible to the BAS if desired Aurora Base Fault odes (AB Only) Fault LED (LED1, ed) ed Fault LED LED Flash ode* Lockout eset/ emove Normal - No Faults OFF Fault - Input 1 No Auto Fault - High Pressure 2 Yes Hard or Soft Fault - Low Pressure 3 Yes Hard or Soft Fault - Freeze Detection FP2 4 Yes Hard or Soft Fault - Freeze Detection FP1 5 Yes Hard or Soft Fault - ondensate Overflow 7 Yes Hard or Soft Fault - Over/Under Voltage 8 No Auto Fault - FP1 & FP2 Sensor Error 11 Yes Hard or Soft NOTE: All codes >11 use long flash for tens digit and short flash for the ones digit. 20, 30, 40, 50, etc. are skipped. AB Basic Faults Aurora Advanced Fault odes (AB + AXB Expansion Board) Fault LED (LED1, ed) AB Basic Faults ed Fault LED LED Flash ode * Lockout eset/ emove Fault ondition Summary Normal - No Faults Off - Fault-Input 1 No Auto Tstat input error. Autoreset upon condition removal. Fault-High Pressure 2 Yes Hard or Soft HP switch has tripped (>600 psi) Fault-Low Pressure 3 Yes Hard or Soft Low Pressure Switch has tripped (<40 psi for 30 continuous sec.) Fault-Freeze Detection FP2 4 Yes Hard or Soft Freeze protection sensor has tripped (<15 or 30 degf for 30 continuous sec.) Fault-Freeze Detection FP1 5 Yes Hard or Soft Freeze protection sensor has tripped (<15 or 30 degf for 30 continuous sec.) Fault-ondensate Overflow 7 Yes Hard or Soft ondensate switch has shown continuity for 30 continuous sec. Fault-Over/Under Voltage 8 No Auto Instantaneous voltage is out of range. **ontrols shut down until resolved. Fault-FP1 & 2 Snsr Error 11 Yes Hard or Soft If FP1 or 2 Sensor Error Fault-ompressor Monitor 10 Yes Hard or Soft Open rkt, un, Start or welded cont Non-riticAXBSnsrErr 13 No Auto Any Other Sensor Error riticaxbsnsrerr 14 Yes Hard or Soft Sensor Error for EEV or HW Alert-HotWtr 15 No Auto HW over limit or logic lockout. HW pump deactivated. Fault-VarSpdPump 16 No Auto Alert is read from PWM feedback. Not Used 17 No Auto IZ2 om Fault. Autoreset upon condition removal. Non-ritomErr 18 No Auto Any non-critical com error Fault-ritomErr 19 No Auto Any critical com error. Auto reset upon condition removal Alarm - Low Loop Pressure 21 No Auto Loop pressure is below 3 psi for more than 3 minutes Alarm - Home Automation 1 23 No Auto losed contact input is present on Dig 2 input - Text is configurable Alarm - Home Automation 2 24 No Auto losed contact input is present on Dig 3 input - Text is configurable NOTES: *All codes >11 use long flash for tens digit and short flash for the ones digit. 20, 30, 40, 50 etc. are skipped! Alert is a noncritical sensor or function that has failed. Normal operation of the heat pump is maintained but service is desired at some point. AB & AXB Advanced Faults 37

38 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL ontrols - UP DD ontrol (optional) cont. Aurora Base or Advanced ontrol onfiguration and Status odes Status LED (LED3, reen) Description of Operation Fault LED, reen Normal Mode ON ontrol is Non-functional OFF Test Mode Slow Flash Lockout Active Fast Flash Dehumidification Mode Flash ode 2 Load Shed Flash ode 5 Emergency Shutdown Flash ode 6 On Peak Mode Flash ode 7 (Future Use) Flash ode 8 (Future Use) Flach ode 9 onfiguration LED (LED2, Yellow) Description of Operation No Software Overwritten DIP Switch Overwritten EM onfiguration Mode eset onfiguration Mode onfiguration LED, Yellow EM Setting Slow Flash Fast Flash OFF 9. Alarm elay The Alarm relay (ALM) is factory connected to 24 VA via jumper JW2. By cutting JW2, AB ALM becomes a dry contact connected to AB AL. The elay is field switchable between Factory setting as an Alarm output or available for other uses. 10. Accessory elay1 A configurable, accessory relay on the AB is provided that can be cycled with the compressor, blower, or the Dehumidifier (DH) input. A third (factory) setting cycles the relay with the compressor but delays the compressor and blower output for 90 sec. Source pump or slow opening solenoid valves in well systems or variable speed primary pumping systems would be a prime use of this feature. Access elay Operation SW2-4 SW2-5 ycle with Blower ON ON ycle with ompressor OFF OFF Water Valve Slow Opening ON OFF ycle with omm. T-stat Hum md OFF ON 11. Electric Heat EH1 A digital 24VD output is provided for electric heat powering. UP s Default programming has EH1 set for AUX/ELE Heat operation and will be controlled using the UP s internal P.I.D. logic. However it can be changed by the BAS to be network controlled. 12. Electric Heat EH2 A digital VD output is provided for field options converted from the original EH2 output. Default UP program has the EH2 output set for Network ontrol but can be changed by the BAS to be controlled by the UP s internal P.I.D. logic. 38

39 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL ontrols - UP DD ontrol (optional) cont. Aurora Advanced ontrol onfiguration and Options (Future Availability on Select Models/onfigurations) 1. Accessory elay2 A second, configurable, accessory relay on the AXB is provided that can be cycled with the compressor 1 or 2, blower, or the Dehumidifier (DH) input. This is to complement the Accessory 1 elay on the AB board. Position DIP 4 DIP 5 Description 1 ON ON ycles with Fan or EM (or ) 2 OFF ON ycles with 1 first stage of compressor or compressor spd ON OFF ycles with 2 second stage of compressor or compressor spd OFF OFF ycles with DH input from AB board 2. Analog Out A standard 0-10VD analog output is provided. This output can be used to drive modulating dampers etc. 3. Variable Speed Pump or Modulating Water Valve - This input and output are provided to drive and monitor a variable speed pump. The VS pump output is a PWM signal to drive the variable speed pump. The minimum and maximum level are set using the AID Tool. 75% and 100% are the default settings respectively. The VS data input allows a separate PWM signal to return from the pump giving fault and performance information. Fault received from the variable speed pump will be displayed as E16. Modulating Water Valve - This Variable speed PWM output is provided to optionally drive a modulating water valve. Through advanced design a 0-10VD valve can be driven directly from the VS pump output. The minimum and maximum level are set in the same way as the VS pump using the AID Tool. 75% and 100% are the default settings respectively. 4. Loop Pump Slaving - This input and output are provided so that two units can be slaved together with a common flow center. When either unit has a call for loop pump, both unit s loop pump relays and variable speed pumps are energized. The flow center then can simply be wired to either unit. The output from one unit should be routed to the input of the other. If daisy chained up to 16 heat pumps can be wired and slaved together in this fashion. 39

40 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL ontrols - UP DD ontrol (optional) cont. Aurora Advanced ontrol Optional Sensor Kits (Future Availability on Select Models/onfigurations) 1. Energy Monitoring (Standard Sensor Kit on Advanced models) - The Energy Monitoring Kit includes two current transducers (blower and electric heat) added to the existing two compressor sensors so that the complete power usage of the heat pump can be measured. The BAview Tool provides configuration detail for the type of blower motor and a line voltage calibration procedure to improve the accuracy. This real time power usage information can be displayed on the AID Tool and is available thru network points when using BAnet or N2 Open. ompressor urrent 1 ompressor urrent 2 Fan urrent Aux Heat urrent Pump Selection Voltage ompressor Watts Fan Watts Aux Heat Watts Pump Watts (VS Only) 3. Performance Monitoring (optional sensor kit) - The optional Performance Monitoring Kit includes: three temperature sensors, entering and leaving water, leaving air temperature and a water flow rate sensor. With this kit, heat of extraction and rejection will be calculated. This requires configuration using the BAview Tool for selection of water or antifreeze. Leaving Air Temperature (supply) Alt Leaving Air Temperature (Supply) Entering Water Temperature Leaving Water Temperature Water Flow Meter Entering Air Temperature (from zone sensor) Brine Selection (water/antifreeze) Heat of Extraction/ejection 2. efrigerant Monitoring (optional sensor kit) - The optional efrigerant Monitoring Kit includes two pressure transducers, and three temperature sensors, heating liquid line, suction temperature and existing cooling liquid line (FP1). These sensors allow the measurement of discharge and suction pressures, suction and liquid line temperatures as well as superheat and subcooling. This information can be displayed on the BAview Tool, or the network when using BAnet and N2. Htg Liquid Line lg Liquid Line Discharge pressure Suction Pressure Discharge Saturated Temp Suction Saturated Temperature Superheat Subooling 40

41 VESATE OMPAT SEIES 50Hz INSTALLATION MANUAL ontrols - UP DD ontrol (optional) cont. ZS Series Net Sensor Overview The ZS Series line of intelligent zone sensors provides the function and flexibility you need to manage the conditions important to the comfort and productivity of the zone occupants. The ZS sensors are available in a variety of zone sensing combinations to address your application needs. These combinations include temperature, relative humidity, and indoor air quality (carbon dioxide or VOs (Volatile Organic ompounds)). They are built to be flexible allowing for easy customization of what the user/ technician sees. Designed to work with the Aurora UP controllers the ZS sensor line includes the ZS Base, ZS Plus, ZS Pro and ZS Pro-F. The UP uses a proprietary communication called net to receive the space temperature from the zone sensor. This is done using (2) 18 AW twisted pair unshielded cables for a total of 4 wires connected to the net port. The sensor gets its power from the UP controller and connecting multiple sensors to one UP will allow for space temperature averaging. The UP can support one ZS Pro or ZS Pro F with up to four ZS standard sensors wired to the net port on the UP for a total of 5 zone sensors. The sensors use a precise 10k ohm thermistor with less than 0.18 F drift over a ten year span, this allows for less maintenance or re-calibration after installation. The sensors also have a hidden communication port for connecting a BAview or local laptop that provides access to the equipment for commissioning and maintenance. The table below shows the features of each of the four sensors that are currently available. ZS Base ZS Pro-F ZS Plus ZS Pro Features ZS Base ZS Plus ZS Pro ZS Pro-F Temp, O 2, Humidity, and VO Options Neutral olor Addressable/supports daisy chaining Hidden communication port Mounts on a standard 2 by 4 electrical box Occupancy Status indicator LED Push button occupancy override Setpoint adjust Large, easy to read LD Alarm indicator F to conversion button Options Part Number Part Number Part Number Part Number Temperature Only ZSU ZSUPL ZSUP ZSUPF Temp with O 2 ZSU- ZSUPL- ZSUP- ZSUPF- Temp with Humidity ZSU-H ZSUPL-H ZSUP-H ZSUPF-H Temp with Humidity, O 2 ZSU-H ZSUPL-H ZSUP-H ZSUPF-H Temp, Humidity, VO ZSU-HV ZSUPL-HV ZSUP-HV ZSUPF-HV Temp with VO ZSU-V ZSUPL-V ZSUP-V ZSUPF-V 41

42 VESATE OMPAT 50Hz SEIES INSTALLATION MANUAL ontrols - UP DD ontrol (optional) cont. Net Sensor Physical and Electrical Data Sensing Element ange Accuracy Temperature (on non-humidity models) (-20 to 50 ) (0.2 ) Temperature (on Humidity models) (10 to 40 ) (0.3 ) Humidity 10% to 90% ±1.8% typical O2 400 to 1250 PPM 1250 to 2000 PPM ±30PPM or +/-3% of reading (greater of two) ±5% of reading plus 30 PPM VO 0 to 2,000 PPM ±100 PPM Power equirements Sensor Type Power equired Temperature Only All Models 12 8 ma Temperature with Humidity All Models ma (idle) to 190 ma (O2 measurement cycle) Temp with VO, or Temp/VO/Humidity All Models ma Temp with O2, or Temp/ O2/Humidity All Models ma (idle) to 190 ma (O2 measurement cycle) Power Supply ommunication Local Access Port Environmental Operating ange Mounting Dimensions A controller supplies the net sensor network with ma. Additional power may be required for your application. See sensor ZS Installation uide 115 kbps net connection between sensor(s) and controller 15 sensors max per net network; 5 sensors max per control program For connecting a laptop computer to the local equipment for maintenance and commissioning (0-50 ), 10% to 90% relative humidity, non-condensing Standard 4 x 2 electrical box using provided 6/32 x 1/2 mounting screws D mmm (same for all) W mm (same for all) H mmm (same for all) (with optional motion sensor) D mm 42