Drain Separator for Vacuum

Transcription

1 Separator for Vacuum Series M emoves water droplets from air by simply installing in vacuum lines. Prevents damage of vacuum pumps and ejectors. Ejector Z Z Z M MV EP elated separator for vacuum side port solenoid valve side Cleaning water Pad Courtesy of Steven Engineering, Inc.-30 yan Way, South San Francisco, C Main Office: (50) Outside Local rea: (800)

2 Separator for Vacuum Series M ohs Over % of water droplets can be removed through the use of a special water droplet removing element. The provision of a drain cock makes it possible to discharge the drain manually after breaking the vacuum. Even when the element is saturated with water, there is almost no drop in pressure (increase in resistance). The element can be replaced with a single touch. M 30 Body size 30 3/8 40 1/ 50 3/4 Thread type Nil c F G N NPT 00 /Combinations How to Order Port size 0 1/4 03 3/8 04 1/ 0 3/ Combination available Pressure gauge position Nil None B Bracket Nil cock Metal bowl Nylon bowl guide (c 1/4) Flow: ight Left If ordering two options or more, indicate symbols numerically and alphabetically. Without valve function (It needs drain piping and piping for a stop valve like ball valves, etc.) Combination not available cock Metal bow Nylon bowl guide Flow: ight Left Symbol Nil Nil M3000 M4000 M5000 ecommended flow rate (l/min (N)) Port size (Nominal size B) 1/4, 3/8 3/8, 1/ 3/4, 1 Mass (kg) Specifications Fluid Maximum operating pressure Minimum operating pressure Proof pressure mbient and fluid temperature Water drop removal ratio Element life ir 1.0 MPa 750 mmhg 1.5 MPa 5 to 0 C % years or when pressure drops to 0.0 MPa ccessory () pplicable model Bracket assembly (With mounting screws) M3000 M4000 M5000 F30P-050S F40P-050S F50P-050S 14 Courtesy of Steven Engineering, Inc.-30 yan Way, South San Francisco, C Main Office: (50) Outside Local rea: (800)

3 Separator for Vacuum Series M How to Order Bowl ssembly M C 30 Symbol Body size pplicable body size M3000 M4000, Nil Polycarbonate bowl (1) Metal bowl Nylon bowl (1) Note 1) The bowl assembly includes a bowl guard (Material: CE). Flow Characteristics Supply pressure (MPa) M5000 M4000 M ir flow rate (l/min (N)) Construction Thread type (3) Nil c F G N NPT Note 3) Select in line with the thread type on the discharge cock guide (c 1/4) () Note ) Without valve function (It needs drain piping and piping for a stop valve like ball valves, etc.) Fluid: ir (pressurized) Measured pressure: Downstream release to atmosphere q q Z Z Z y r w e t w y r e M MV EP elated Component Parts No. Description 1 Body Material luminum die-casted Note Platinum silver coated eplacement Parts No. Description Material Part no. M3000 M4000 M Element assembly Bowl assembly Note) O-ring O-ring Spacer M-EL3000 M-C30- C3SFP-0S 3073 M-EL4000 M-C40- C4SFP-0S M-EL5000 M-C40- C4SFP-0S Note) efer to the above for How to Order Bowl ssembly. The spacer y is not included in the bowl assembly. Courtesy of Steven Engineering, Inc.-30 yan Way, South San Francisco, C Main Office: (50) Outside Local rea: (800)

4 MX.D LEVEL MX.D LEVEL Series M Dimensions M3000, 4000 L G K D F M Bracket () C space 40 E H Vacuum x port size Discharge guide (-) c 1/8 P 1/4 female thread without valve function Hexagon width across flats 4 M5000 L G K D F M Bracket () space 0 C B E H x port size Vacuum c 1/8 Port size M3000 M4000 M5000 1/4, 3/8 3/8, 1/ 3/4, 1 Note) ( ) is the case for metal bowl. C D B Note) 14 (15) 00 (03) 79 (81) Bracket mounting dimensions E F G H K L M (mm) With drain guide Note) 158 (10) 194 (195) 73 (74) 1 Courtesy of Steven Engineering, Inc.-30 yan Way, South San Francisco, C Main Office: (50) Outside Local rea: (800)

5 Series M Specific Product Precautions Be sure to read before handling. efer to front matters 38 and 39 for Safety Instructions and pages 844 to 84 for Vacuum Precautions. separator for vacuum port solenoid valve side Cleaning water on Design 1. When using with repeating positive pressure and negative pressure: Use at 0.1 MPa or less of positive pressure when the repeating tact is fast. The vessel may be hotter depending on the pressure and repeating tact conditions. Mounting 1. ir piping should be thoroughly flushed before mounting.. When piping and fittings, etc. are being screwed together, be certain that cutting chips from the pipe threads, sealing material, and other debris do not get inside the piping. Further, when pipe tape is used, leave 1.5 to thread ridges exposed at the end of the pipe. 3. The unit should be mounted vertically. 4. When piping is being installed, connect for work side and for ejector or vacuum pump. Ejector side Warning Bowl Capacity M3000 M4000, 5000 Operating Environment 1. Since the case material is polycarbonate, avoid using chemicals such as thinner, carbon tetrachloride, chloroform, aniline, cyclohexan, trichloroethylene, sulfric acid, lactic acid or watermiscible cutting fluid (alkaline), etc. Operation of the product in an atmosphere containing any of these chemicals should also be avoided. neutral detergent may be used for cleaning the bowl.. void use exposed to direct sunlight. 1. The element should be replaced after years of use, or before the pressure drops to 0.0 MPa (0. kgf/cm ). The spacer and O-ring should also be replaced at the same time that the element is replaced. Sometimes when the bowl is removed for a purpose other than replacing the element, the spacer may stick to the bowl and come off. In this case however, it may be returned to its installed position and used again.. age should be discharged by the time it reaches the upper limit. Furthermore, when drainage is to be discharged or the element replaced, first confirm that all equipment, etc is stopped, and return the interior of the bowl to atmospheric pressure before proceeding. 45 cm cm 3 Z Z Z M MV EP elated Pad 5. When drainage is discharged automatically, install port solenoid valve and activate it in such an operation cycle like the drainage should be discharged by the time it reaches the upper limit. But when discharging it, return the case interior to atmospheric pressure before proceeding. Courtesy of Steven Engineering, Inc.-30 yan Way, South San Francisco, C Main Office: (50) Outside Local rea: (800)