Código : Motc.PANASC/SANYO-CSB453H8A--6HP-15100fr

Transcription

1 Código : Motc.PANASC/SANYO-CSB453H8A--6HP-151fr Section 1. General Specifications Content Unit Specification Compressor Model (Code) C-SB453H8A ( ) Type Application Evap. Temp. Range Compressor Cooling Type Phase Hermetic Scroll Compressor High Back Pressure -15~12 (5~54) Natural Cooling 3 Power Source Voltage Range Rated Voltage Rated Frequency V /44-46 Hz 5/6 V 342~456/396~56 Weight (Including Oil) Refrigerant kg (lb) 39.5(87.1) R22 Oil Type SAY56T or Equivalent Oil Charge ml (fl oz) 17 (57.5) Displacement cm 3 (in 3 ) /rev 1.(6.1) Motor Type Number of Poles 3-PH Induction Motor 2 Electrical Insulation Class E Motor Nominal Revolution Locked Rotor Ampere Winding Resistance [at 25 C (77 F)] min /349 A 66/72 U-V Ω U-W V-W Suction Line (O.D.) mm (in) 22.2 (.875) Connection Tube Discharge Line (O.D.) Compressor Surface Paint mm (in) 12.7 (.5) Black Paint Notes 1 Voltage range is applied at standard rating conditions. 2 Motor specifications in the table are the average values for your reference. 3 ( ): All units with parentheses are reference values. 4 Certifications: CCC certificate No TUV certificate No.Z UL certificate No.SA Expiration of Specification Expiration of this specification shall be effected until issuing a notice with indication of the expiration date from the issued date. In case of improvement or elimination of this specification, it shall be handled by the revision record based on agreement between both sides. 2

2 Section 2. Performance Warranty 2.1 Performance Power Source (3PH) Hz 5 6 V Remark Capacity Input Power Current W 17,7 21,5 ±7% (BTU/hr) 6,392 73,358 reference W 5,43 6,64 ±7% A ±7% Standard Rating Conditions Condensing Temp. Evaporating Temp. Suction Gas Temp. Liquid Temp. Ambient Temp. 54.4(13) 7.2( 45 ) 18.3( 65 ) 46.1(115) 35( 95 ) 2.2 Sound Level Power Source (3PH) Hz 5 V Sound Level db(a) 62Max. 67Max. Notes 1 The operating conditions are the same as MIC location is the distance of 1m (3.28feet) from the compressor. 3 Sound Level is an average sound pressure level in four directions. 2.3 Minimum Starting Voltage Power Source (3PH) Minimum Starting Voltage Conditions Hz 5 V Compressor Temp. Ambient Temp. High Pressure Low Pressure MPa(G)/psig MPa(G)/psig 1~6(5~14) 1~4(5~15) 2(29).5(72) 2.4 Others Content Unit L.P. S. MPa(G)/psig Design Pressure H. P. S. MPa(G)/psig Insulation Resistance MΩ Dielectric Strength V Residual Moisture mg Note: 1. The insulation resistance be measured with a DC5V megohm tester. Specification 1.6(232) 3.(435) 1 (without refrigerant) 24 (1 second) 3 3

3 Section 3. Standard Accessories 3.1 Accessories List Parts Name Qty Parts code Revision No. Note Terminal Box Cover 1 A-11-DSB Installed on Compressor Terminal Box Clip 1 A-21-DSB Installed on Compressor Insulating Grommet 1 A-31-DSB Installed on Compressor Mounting Grommet 4 M-11-DSB Included with Compressor Mounting Sleeve 4 M-21-DSB Included with Compressor Screw Special 1 B-11-DSB Installed on Compressor 3.2 The Drawing for Reference Parts Name Compressor Outline Drawing Mounting Parts Listing Packing Dimensions Nameplate Wiring Diagram Parts Code D-11-DSB M-511-DSB D-21-DSB A-513-DSB E-91-DSB Revision No Inernal Moter Protector (in compressor) Parts Name Specification Trip Temprature 145±5 Inernal Motor Protector Reset Temprature 61±9 Trip Current 57A / 2~1s 4

4 Section 4. Compressor Protection 4.1 Protection Required but not Included with compressor Protection Device Reversal Defensible Relay Crankcase Heater Discharge Thermostat High Pressure Switch Low Pressure Switch Items Features Rated Voltage Rated Power Mounting Position Trip Temperature Reset Temperature Setting Setting Specifications To protect the compressor from reverse rotation AC38V 35 Watts Located within 1mm(4 in )from the compressor shell 13±5 (266 ±1 F) 95±11 (25 ± 2 F) Cut-out seting no higher than 3.Mpa(G) Cut-out seting no lower than.3mpa(g) 4.2 Position of the Protection and Refrigerant Charging FOR LIQUID REFRIGERANT CHARGING CAPILLARY OUTDOOR HEAT EXCHANGER LIQUID LINE SERVICE VALVE INDOOR HEAT EXCHANGER REVERSING VALVET GAS LINE SERVICE VALVE HIGH PRESSURE SWITCH DISCHARGE THERMOSTAT ACCUMULATOR FOR GAS REFRIGERANT CHARGING LOW PRESSURE SWITCH COMPRESSOR CRANKCASE HEATER 5

5 Section 5. Operating Envelope Suction Gas Superheat: 11.1K Refrigerant: R22 7 Transient Operation 6 Condensing Temperature( ) Normal Operation Evaporating Temperature( ) 6

6 Section 6. Application Standard & Limit The following requirements apply to vertical type hermetic scroll compressors: Standard: Applicable to ordinary conditions in Japan JIS B8616 or standards relative to JIS B8616, such as standard rating conditions, maximum operating conditions, low temperature conditions, etc. Limit: Applicable to transitional brief period of time, such as start-up and beginning of defrost mode. No. Item Standard Limit Note 1 Refrigerant R22(Meet the standard of Japan JIS K1517) 2 Evaporating Temp. -15~12 (5~54 F) -25~15 (-13~59 F) Comp. Suction Pressure.2~.62MPa(G)(29~9psig).1~.69MPa(G)(14.5~1psig) 3 Condensing Temp. 3~65 (86~149 F) 1.9~2.6MPa(G)(158~377psig) 68 (155 F) 2.78MPa(G)(43psig) Comp.Design Pressure(High) 3.MPa(G) (435psig) 4 Compression Ratio 5 Winding Temp. 2 ~ (24 F) Max. 125 (257 F) 6 Shell Bottom Temp. 9 (194 F) Max. Evaporating Temp.+12 (21 F) Min. Ambient Temp.+11 (2 F) Min. Operating Not Operating 7 Discharge Gas Temp. 115 (24 F) Max. C-SB:13 ( 266 F) Max. C-SC:135 ( 275 F) Max. Temp. within 1mm(4in) of the discharge fitting. Temp. inside of the well pipe on the top of compressor 8 Suction Gas Temp. Superheat: 5K(1 F)Min. No excessive noise It should meet the requirement of item 5, 6, 7 and 14 within 3cm of the suction fitting. 9 Running Voltage 1 Starting Voltage Within ±1% of the rated voltage Three Phase Models: 85% of the rated voltage min. Single Phase Models: 9% of the rated voltage min. Voltage at compressor terminals. Voltage at compressor terminals. 11 On/Off Cycling On Period: Until the oil level returns to the center of the lower bearing Off Period: Until balance of high and low pressure is obtained For at least 7 minutes - on/3 minutes-off is recommendable. 12 Refrigerant Charge 13 Life Time oil/refrigerant(wt.).35 2, cycle Specific gravity of the Oil: Minimum Oil Level C-SB: Center of the lower bearing C-SB:Bottom of the lower bearing C-SC:No less than 7% of the initial oil charge 15 Abnormal Pressure Rise/Drop System Moisture 16 Level System 17 Uncondensable Gas Level 18 Tilt Pressure Rise: 3.MPa(G) (435psig) Max. Pressure Drop:.3MPa(G) (4.35psig) Min. 2ppm Max. 1 Vol.% Max. Residual Oxygen.1 Vol.% Max. 5 Deg.Max. By high pressure switch By low pressure switch 24 hrs. after vacuuming: 1.1kPa Max. Operation beyond the above limits must be approved by Dalian SANYO Compressor Co., Ltd. (G): Gauge Pressure 7

7 Notes 1 Installation should be completed within 15 minutes after removing the rubber plugs. 2 Do not use the compressor to compress air. 3 Do not energize the compressor under vacuumed conditon. 4 Liquid refrigerant should be charged on liquid line between condenser and receiver. Do not charge the liquid refrigerant on the suction or discharge pipe of the compressor. 5 Do not tilt over the compressor while carrying it. 6 Do not remove the paint. 7 Crankcase heater is required when the oil sump temperature is too low to meet the requirement of item 6 on page7. 8 Voltage fluctuation between compressor terminals, during operation, shall be within 2% of the rated voltage. 9 Do not operate compressor in reverse rotational direction. 1 Suction strainers are recommended for all applications. 8

8 Voltage drop may occur due to the large current draw during compressor starting. We recommend selecting the wire size from the table below. Section 7. Selection of Electrical Wire 6.1 Type of Unit Window & Commercial Type Unit power source 1 outdoor indoor terminal plate 2 compressor Split Type(Separate Type) outdoor power source 1 indoor 2 terminal plate 3 compressor 6.2 Size Table of Electrical Wire Size of electrical wire(mm 2 ) Starting current (A) Remark 1 or Remark 1+2(heat-resistance Temperature: 6 C(14 F) min. ) Remark3(heatresistance Temperature: 12 C(248 F) min.) 5m max. 1m max. 15m max. 2m max. 3m max. 5m max. 1m max. 2max max max max max max max max max max. 12max max max max max max max Caution of Ground The internal motor protector does not protect the compressor against all possible conditions. Please be sure that the system utilizes the ground connection when installed in the field. 9

9 238.2 [9.378] 19.5 [7.55] HOLE 4-φ18 φ.79 No. Part Code Qty Name Compressor 2 A-11-DSB 1 Terminal Box Cover 3 A-21-DSB 1 Terminal Box Clip 4 A-31-DSB 1 Insulating Grommet 5 A-513-DSB 1 Nameplate 6 B-11-DSB 1 Screw Special 12.3 [4.74] [4.889] 19.5 [7.55] 14. [5.513] [5.169] [9.378] DISCHARGE TUBE φ13.1 [φ.516] 77.2 [3.39] [2.923] SUCTION TUBE φ22.3 [φ.878] 68.2 [2.685] U V W [17.785] 259. [1.25] φ176.4 [φ6.952] 31.9 [12.249] 42.8 [16.567] TERMINAL [.985] Part Code D-11-DSB Name Compressor Outline Drawing

10 1 4 [1.575] No. Part QTY Name 1 M-11-DSB 4 Mounting Grommet 2 M-21-DSB 4 Mounting Sleeve 3 B-11-DSB 1 Screw Special WASHER M8 BOLT WASHER SPRING 8 [.315] 3 COMPRESSOR BASE R16 [R.63] 2 [.787] 32 [1.26] [1.811] 37. [1.457] M4[1.575] 1 24 [.945] 19 [.748] 46 [1.811] 2 R3 [R.118] 11 [.433] 1 [.394] 38 [1.496] 46 [1.811] φ8.6 [φ.339] φ1.6 [φ.417] 19 [.748] Part Code M-511-DSB Name Mounting Parts Listing

11 ` 1125 [44.291] [45.197] 116 [45.669] 186 [42.756] [ ] 41 [2.362] 6[2.362] 9[3.543] 6 [2.362] 41 [2.362] 6[2.362] 1-5 [ ] Part Code D-21-DSB Name Packing Dimensions

12 12 13 CODE MODEL C-SB453H8A AC 3PH 5Hz 38,415V AC 3PH 6Hz 44,46V REF. R22 OIL SAY56T DALIAN SANYO COMPRESSOR CO.,LTD. WARNING TERMINAL MUST BE CONNECTED WITH WIRE AS FOLLOWS COMPRESSOR MAY HAVE TROUBLE DUE TO INCORRECT WIRING 注意端子和配线请按照下图标示连接 配线错误可能会导致压缩机故障 3F XXXXXXXXX 8 MFG.DATE XXXX.XX.XX SERIAL NO. XXXXXXX MADE IN CHINA XXXXXX Part Code A-513-DSB Name Nameplate

13 SWITCH V POWER SUPPLY 5Hz 38~415V R S T U INTERNAL PROTECTOR W MAGNETIC SWITCH COMPRESSOR R C 14 POWER SUPPLY 5Hz 22V S T REVERSAL DEFENSIBLE RELAY B A CRANKCASE HEATER Part Code E-91-DSB Name Wiring Diagram