Sinus Jevi (Explosion-Proof) Condens Heaters

Transcription

1 Sinus Jevi (Explosion-Proof) Condens Heaters Heating elements for dehumidification of sealed switchboards and control cabinets. Due to temperature limitations on e.g. print and plastic cabinets it is important to use a heating element with a large surface and thus a low surface temperature. The condens heater is designed to meet these properties. Liquids Gasses Solids Spaces Resistors Sinus-Jevi Electric Heating B.V. Aambeeld NT Medemblik +31 (0)

2 Anti-Condensation Heaters Heating elements for dehumidification of sealed switchboards and control cabinets. Due to temperature limitations on e.g. print and plastic cabinets it is important to use a heating element with a large surface and thus a low surface temperature. The condens heater is designed to meet these properties. The temperature limit (appr. 65 C) is integrated into the construction and the small physical measurements enables installation in most cabinets and switchboards. The cooling fin profile has an optimal surface in relation to heat loss in circulation airflow. The element is made of black anodized aluminium which optimises heat conduction and emission. INSTALLATION The anti-condensation heater should always be mounted with the cooling ribs in vertical position. The best circulation is achieved by placing the heating element at the lower part of the cabinet. Due to the element s low surface temperature, the position in relation to other components in the cabinet is not critical. Although it is recommended to maintain 5 cm free space on the sides and approx. 3 cm free space to the bottom due to air circulation. CONSTRUCTION The cooling fin profile has an optimal surface in relation to heat loss in circulating airflow. The element is made of black anodized aluminium which optimises heat conduction and emission. The anti-condensation heater is supplied with temperature limit or as a selflimiting construction where a PTC element supplies the profiles with power according to the surrounding temperature. The small cabinet heating element is without thermostat and casted in silicone rubber. The element is supplied with tape for attachment onto the cabinet. Can be used in places where the available space is very limited. the element can be bent with a min. radius of 15 mm. A TECHNICAL SPECIFICATIONS Type Power Voltage Length x Width x Height Proofing Article number Profile OHMSK 9 Watt 230 Volt 100 x 30 x 8 mm IP44 A Silicone OHMSK 70 Watt 230 Volt 142 x 72 x 57 mm IP55 A OHMSK 160 Watt 230 Volt 250 x 116 x 33 mm IP55 A PTC 15 Watt Volt 75 x 72 x 52 mm IP55 A PTC 15 Watt Volt 75 x 72 x 52 mm IP55 A PTC 20 Watt Volt 100 x 116 x 33 mm IP55 A PTC 40 Watt Volt 250 x 116 x 33 mm IP55 A PTC 20 Watt Volt 100 x 116 x 33 mm IP55 A PTC 40 Watt Volt 250 x 116 x 33 mm IP55 A PTC 20 Watt Volt 100 x 116 x 33 mm IP55 A PTC 40 Watt Volt 250 x 116 x 33 mm IP55 A A A

3 Anti-Condensation heater type SEK To prevent condensation inside switch and instrument cabinets; To keep the cabinets frost-free; To maintain a constant temperature inside the cabinet, independent of the weather s influence. The different models can be supplied self-adjusting or with built-in or surfacemounted thermostats. In order to keep switch cabinets free of condensation, the following guidelines are employed: - Switch cabinet for indoor use: Watt per m³ cabinet volume. - Switch cabinet for outdoor use: Watt per m³ cabinet volume - Switch cabinet for outdoor use in extreme circumstances: Watt per m³ cabinet volume. In extraordinary cases, we recommend that you ask for advice. INSTALLATION Mounting depends on the type. Because of inductive radiation, some types of cabinet heaters must be mounted at least 40 mm away from sensitive equipment or wiring. To make full use of the heat-emission from the cabinet heaters, it is important to place the heating element as low as possible in the cabinet. In case of wide cabinets, it is advisable to place more and/or longer elements for optimal heat distribution. In larger cabinets, it is sometimes advisable to install a fan. CONSTRUCTION The connecting voltage is 230 Volt. TECHNICAL SPECIFICATIONS Type Power Voltage Length x Width Material Article number SEK Watt 230 Volt 100 x 40 mm Mica A Anti-Condensation heater type SHZ The cabinet heaters type SHZ are especially designed for application where a high output is required. The heaters are provided with a surface-mounted adjustable room-thermostat, range 5 C - 30 C, and 500 mm long connection lead. The SHZ cabinet heater is also available without thermostat. In that case, the heater has to be controlled by an external control thermostat. Proofing: IP65 (IP30 when thermostat is mounted). TECHNICAL SPECIFICATIONS Type Power Voltage Length x Width Proofing Material Article number SHZ Watt 230 Volt 330 x 165 mm IP30 Galvanised steel A SHZ Watt 230 Volt 580 x 165 mm IP30 Galvanised steel A

4 Anti-Condensation heater type GSM Direct Heaters for non-hazardous (safe area) locations, designed for: anticondensation, freeze protection and All Cameo Heaters are designed around self-limiting heating consumption. Our Cameo Space Heaters are designed to heat the air inside an enclosure and indirectly the installed equipment. If properly selected for freeze protection, no thermostat will be needed. In other situations, if the equipment may not exceed a maximum temperature value, you can add one of our thermostats for non-hazardous areas. Do not cover the fins to guarantee free convection. Voltage AC/DC: Ambient temp. range: other lengths optional, on request appr gr. 164 x 54 x 54 mm (LxWxH) black anodised aluminium. 110/240 Volt -60 C C optional: non braided GSM-1A Appr. 115 C surface temperature* Watt A A GSM-2A Appr. 105 C surface temperature* Watt A A GSM-3A Appr. 90 C surface temperature* Watt A A GSM-4A Appr. 70 C surface temperature* Wat A A High power model GSM-0AHP Appr. 130 C surface temperature* Watt A A Also mounting brackets available for this type Type GSM Anti-Condensation heater type GSMLP Direct Heaters for non-hazardous (safe area) locations, designed for: anticondensation, freeze protection and All Cameo Heaters are designed around self-limiting heating consumption. Our Cameo Space Heaters are designed to heat the air inside an enclosure and indirectly the installed equipment. If properly selected for freeze protection, no thermostat will be needed. In other situations, if the equipment may not exceed a maximum temperature value, you can add one of our thermostats for non-hazardous areas. Do not cover the fins to guarantee free convection. Voltage AC/DC: Ambient temp. range: other lengths optional, on request appr gr. 100 x 54 x 54 mm (LxWxH) black anodised aluminium. 110/240 Volt -60 C C Type GSMLP optional: non braided GSMLP-1A Appr. 115 C surface temperature* Watt A A GSMLP-2A Appr. 105 C surface temperature* Watt A A GSMLP-3A Appr. 90 C surface temperature* Watt A A GSMLP-4A Appr. 70 C surface temperature* Wat A A High power model GSMLP-0AHP Appr. 130 C surface temperature* Watt A A 4

5 Anti-Condensation Direct heater type GCT Direct Heaters for non-hazardous (safe area) locations, designed for: freeze protection, anti-condensation and All Cameo Heaters are designed around self-limiting heating consumption. Our Cameo Direct-Heaters are designed to heat air inside an enclosure and indirectly the installed equipment. If properly selected for freeze protection, no thermostat will be needed. In other situations, if the equipment may not exceed a maximum temperature value, you can add one of our thermostats for non-hazardous areas. Voltage AC/DC: Ambient temp. range: other lengths optional, on request appr. 600 gr. 88 x 70 x 35 mm (LxWxH) black anodised aluminium. 110/240 Volt -60 C C optional: non braided Type Article number Type GCT Incl. hexagonal spacers GCT-1A T3 Appr. 115 C surface temperature* Watt A A GCT-2A T4 Appr. 105 C surface temperature* Watt A A GCT-3A T4 Appr. 90 C surface temperature* Watt A A GCT-4A T4 Appr. 70 C surface temperature* Watt A A This type is also available in stainless steel Anti-Condensation Direct heater type GLP Direct Heaters for non-hazardous (safe area) locations, designed for: freeze protection, anti-condensation and All Cameo Heaters are designed around self-limiting heating consumption. Our Cameo Direct-Heaters are designed to heat air inside an enclosure and indirectly the installed equipment. If properly selected for freeze protection, no thermostat will be needed. In other situations, if the equipment may not exceed a maximum temperature value, you can add one of our thermostats for non-hazardous areas. Voltage AC/DC: Ambient temp. range: other lengths optional, on request appr. 600 gr. 78 x 30 x 34 mm (LxWxH) black anodised aluminium. 110/240 Volt -60 C C optional: non braided Type GLP GLP-1A T3 Appr. 115 C surface temperature* Watt A A GLP-2A T4 Appr. 105 C surface temperature* Watt A A GLP-3A T4 Appr. 90 C surface temperature* Watt A A GLP-4A T4 Appr. 70 C surface temperature* Watt A A 5

6 Thermostat type Fix-Therm 96 GTH For non-hazardous areas is the Fix-Therm 96 GTH thermostat very suitable. Often used as maximum thermostat in instrumentation cabinets with space heating, to protect the equipment from overheating, or as a minimum thermostat with space heating to protect from freezing. Article number: A Setpoint: from 10 C up to 130 C Housing: Anodised aluminium housing (stainless steel housing available) Current/Voltage: 6A / 240 VAC Temperature classification: T6 and T4 Cable: 3 x 0.75 mm² silicone braided cable, optional: non braided cable. other lengths optional. 30 x 58 mm (ØxH) appr. 160 gr. Switch: SPST Set point tolerance: +/- 3 C Hysteresis: appr. 2 C Mounting bracket: available (B) RANGE Aluminium: TH-10/5 - going up with 5 C setpoints e.g. 10/5-15/10-20/15 etc. up to 130 C maximum. 6

7 Explosion-Proof Space Heater type SM Space Heaters for hazardous locations, this compact model is designed for: anticondensation, freeze protection and All Smart Heaters are designed around self-limiting heating consumption. Our Smart Space Heaters are designed to heat the air inside an enclosure. The cabinet heater can be controlled by our (ex) room thermostats. Do not cover the fins to guarantee free convection. Ex protection class: Certification: Protection degree: Voltage AC/DC: 110/240 Ambient temp. range: -60 C C appr. 350 gr. 164 x 54 x 54 mm black anodised aluminium II2G Ex d IIC T3 or T4 II2D Ex td A21 IP66 T135 C/200 C KEMA 01ATEX2124X IP66 Power consumption: Watt or Watt optional: non braided cable Type SM SM-1A T3 Appr. 115 C surface temperature* Watt A A SM-2A T4 Appr. 105 C surface temperature* Watt A A SM-3A T4 Appr. 90 C surface temperature* Watt A A SM-4A T4 Appr. 70 C surface temperature* Watt A A High power model SM-0AHP T3 Appr. 130 C surface temperature* Watt A A Explosion-Proof Space Heater type SMLP Space Heaters for hazardous locations, this compact model is designed for: anticondensation, freeze protection and Ex protection class: appr. 350 gr. 100 x 54 x 54 black anodised aluminium II2G Ex d IIC T3 or T4 II2D Ex td A21 IP66 T135 C/200 C Certification: KEMA 01ATEX2124X All Smart Heaters are designed around self-limiting heating consumption. Our Smart Space Heaters are designed to heat the air inside an enclosure. The cabinet heater can be controlled by our (ex) room thermostats. Do not cover the fins to guarantee free convection. Protection degree: Voltage AC/DC: Ambient temp. range: IP66 110/ C C Power consumption: Watt or Watt optional: non braided cable Type SMLP SMLP-1A T3 Appr. 115 C surface temperature* Watt A A SMLP-2A T4 Appr. 105 C surface temperature* Watt A A SMLP-3A T4 Appr. 90 C surface temperature* Watt A A SMLP-4A T4 Appr. 70 C surface temperature* Watt A A High power model SMLP-0AHP T3 Appr. 130 C surface temperature* Watt A A 7

8 Explosion-Proof Space Heater type SP Direct Heaters for hazardous locations, designed for direct mounting onto e.g. manufolds etc. Used for anticondensation, freeze protection and All Smart Heaters are designed around self-limiting heating consumption. Our Cameo Direct Heaters are designed to heat the air inside an enclosure and indirectly the installed equipment. If properly selected for freeze protection, no thermostat will be needed. In other situations, if the equipment may not exceed a maximum temperature value, you can add our Fix-Therm96 thermostat as a maximum temperature protection, in the system When required in other applications, e.g. analyzers, it is normal practice to use our Direct Heaters in combination with our Fix Therm96 thermostats (range from 10 C up to 130 C). Do not cover the fins to guarantee free convection. Type SPA Power consumption: Watt or Watt SP-1A T3 Appr. 115 C surface temperature* Watt A A SP-2A T4 Appr. 105 C surface temperature* Watt A A SP-3A T4 Appr. 90 C surface temperature* Watt A A SP-4A T4 Appr. 70 C surface temperature* Watt A A High power model SP-0AHP T3 Appr. 130 C surface temperature* Watt A A Explosion-Proof Space Heater type LPAF Direct Heaters for hazardous locations, designed for direct mounting onto e.g. manufolds etc. Used for anticondensation, freeze protection and All Smart Heaters are designed around self-limiting heating consumption. Our Cameo Direct Heaters are designed to heat the air inside an enclosure and indirectly the installed equipment. If properly selected for freeze protection, no thermostat will be needed. In other situations, if the equipment may not exceed a maximum temperature value, you can add our Fix-Therm96 thermostat as a maximum temperature protection, in the system When required in other applications, e.g. analyzers, it is normal practice to use our Direct Heaters in combination with our Fix Therm96 thermostats (range from 10 C up to 130 C). Do not cover the fins to guarantee free convection. Power consumption: Watt 8 optional: non braided cable 165 x 164 x 60 mm black anodised aluminium Ex protection class: II2G Ex d IIC T3 or T4 II2D Ex td A21 IP66 T135 C/200 C Certification: KEMA 01ATEX2124X Protection degree: IP66 Voltage AC/DC: 110/240 Ambient temp. range: -60 C C optional: non braided cable 164 x 100 x 60 mm black anodised aluminium Ex protection class: II2G Ex d IIC T3 or T4 II2D Ex td A21 IP66 T135 C/200 C Certification: KEMA 01ATEX2124X Protection degree: IP66 Voltage AC/DC: 110/240 Ambient temp. range: -60 C C Type LPAF LPAF-1A T3 Appr. 115 C surface temperature* Watt A A LPAF-2A T4 Appr. 105 C surface temperature* Watt A A LPAF-3A T4 Appr. 90 C surface temperature* Watt A A LPAF-4A T4 Appr. 70 C surface temperature* Watt A A

9 Explosion-Proof Direct Heater type LP(S) Direct Heaters for hazardous locations, this model is designed for: anticondensation, freeze protection and All Direct Heaters are designed around self-limiting heating consumption. Our Direct Heaters are designed to heat the installed equipment. If properly selected for freeze protection, no thermostat will be needed. Alternative 316 Stainless Steel heaters can be delivered for the Watt range. Also possible is an aluminium body with four holes drilled through, for easy mounting. (or Stainless Steel) Ex protection class: II2G Ex d IIC T3 or T4 II2D Ex td A21 IP66 T135 C/200 C Certification: KEMA 01ATEX2124X Protection degree: IP66 Voltage AC/DC: 110/240 Ambient temp. range: -60 C C Additional Technical data for the High Power model LP-0AHP Power: Watt 88x36x36 mm black anodized aluminium nly All other data: the same as the low power models Power consumption: Watt or Watt optional: non braided cable appr. 350 gr. (Stainless Steel 360 gr.) 78 x 30 x 34 mm black anodised aluminium Type LP(S) LP-1A T3 Appr. 115 C surface temperature* Watt A A LP-2A T4 Appr. 105 C surface temperature* Watt A A LP-3A T4 Appr. 90 C surface temperature* Watt A A LP-4A T4 Appr. 70 C surface temperature* Watt A A High power model LP-0AHP T3 Appr. 130 C surface temperature* Watt A A Type (Stainless steel) Article number Incl. hexagonal spacers LP-1AS T3 Appr. 115 C surface temperature* Watt A A LP-2AS T4 Appr. 105 C surface temperature* Watt A A LP-3AS T4 Appr. 90 C surface temperature* Watt A A LP-4AS T4 Appr. 70 C surface temperature* Watt A A High power model LP-0AHPS T3 Appr. 130 C surface temperature* Watt A A Also mounting brackets available for this type 9

10 Explosion-Proof Direct Heater type CT Direct Heaters for hazardous locations, this model is designed for: anticondensation, freeze protection and All Direct Heaters are designed around self-limiting heating consumption. Our Direct Heaters are designed to heat the installed equipment. If properly selected for freeze protection, no thermostat will be needed. appr. 550 gr. 88 x 70 x 35 mm black anodized aluminium Ex protection class: II2G Ex d IIC T3 or T4 II2D Ex td A21 IP66 T135 C/200 C Certification: KEMA 01ATEX2124X Protection degree: IP66 Voltage AC/DC: 110/240 Ambient temp. range: -60 C C Alternative 316 Stainless Steel heaters can be delivered for the Watt range. Also possible is an aluminium body with four holes drilled through, for easy mounting. Power consumption: Watt optional: non braided cable Type CT CT-1A T3 Appr. 115 C surface temperature* Watt A A CT-2A T4 Appr. 105 C surface temperature* Watt A A CT-3A T4 Appr. 90 C surface temperature* Watt A A CT-4A T4 Appr. 70 C surface temperature* Watt A A Explosion-Proof Direct Heater type CS Direct Heaters for hazardous locations, this model is designed for: anticondensation, freeze protection and All Direct Heaters are designed around self-limiting heating consumption. Our Direct Heaters are designed to heat the installed equipment. If properly selected for freeze protection, no thermostat will be needed. Ex protection class: Certification: Protection degree: Voltage AC/DC: 110/240 Ambient temp. range: -60 C C Stainless Steel II2G Ex d IIC T3 or T4 II2D Ex td A21 IP66 T135 C/200 C KEMA 01ATEX2124X IP66 Power consumption: Watt optional: non braided cable appr. 550 gr. 85 x 65 x 28 mm Type CS CS-1A T3 Appr. 115 C surface temperature* Watt A A CS-2A T4 Appr. 105 C surface temperature* Watt A A CS-3A T4 Appr. 90 C surface temperature* Watt A A CS-4A T4 Appr. 70 C surface temperature* Watt A A This type is also available in a general purpose 10

11 Explosion-Proof Thermostat type Fix Therm96 The Explosion-proof FixTherm96 thermostats are often used as maximum thermostat in instrumentation cabinets with space heating for temperature protection and to protect the equipment from overheating. The housing is made from anodized alumnium or stainless steel type 316 (on request). When required in other applications, e.g. analyzers, it is normal to practice to use our space heaters in combination with these FixTherm96 thermostats (range from 10 C up to 130 C). The FixTherm96 can also be used for cooling purposes e.g. FixTherm TH- 10/5F (N.O. contact) Article number: Housing: Current / Voltage: Cable: A Anodized aluminium or stainless steel 6A/240VAC 3x0.75mm² optional: non braided appr. 160 gr. o.d. 30 mm x 58 mm length Switch: SPST Set-point tolerance: +/- 3 C Hysteresis: appr. 2 C Mounting bracket: available (B) Ambient temp. range: C Ex protection class: II2 G Ex d IIC T6 or T4 II2 D Ex td A21 IP66 T85 C or T 135 C Certificate: KEMA 01ATEX2125X RANGE Aluminium: TH-10/5 - going up with 5 C setpoints e.g. 10/5-15/10-20/15 etc. up to 130 C maximum. Stainless steel bodies: identical range. Explosion-Proof Thermostat type ATH Technical specifications Type : Ex Therm-AT Material casing : polyester Setting range : C Switching power : 1-2: AC 16(2,5)A 230V, 1-4: AC 6,3(2,5)A 230V Max. ambient temp. : 40 C Dimensions : 106 x 200 x 90 mm Protection class : IP65 Article number : A Weight : approx gram Certificate : Ex II 2G Ex de IIC T6 Gb Ex II 2D Ex tb IIIC T130 C Db 11

12 Explosion-proof thermostat type EJB D8525 The explosion-proof room thermostat is suitable for gas group IIB with EN/IEC test certificate. The explosion-proof room thermostat consists of a cast flame proof aluminium casing, fitted with 1 or 2 explosion-proof cable glands for armored cable with an outer diameter of 10.5 to 16 mm and an inner diameter of 7.5 to 11.9 mm. Cable gland M20x1.5 HAWKE type 501/453/O. In the aluminium casing a capillary thermostat is built in, adjustable between 0-40 C. The sensor is mounted on the outside of the casing. Technical specifications Type : 1 phase D8525 Supplied with : 2 brass glands (1 cable gland) Material : aluminium casing Setting range : C Ambient temperature : -25 C C Hysteresis : 1.5 C Switching power : max. 16A at 400 Volts AC Sensor dimensions : 147 x Ø6 mm Protection class : IP66 Article number : A Type : 3 phase D8525 Supplied with : 3 brass glands (2 cable glands) Material : aluminium casing Setting range : C Ambient temperature : -25 C C Hysteresis : 2 C Switching power : max. 3x400 Volts AC to 3x16A Sensor dimensions : 210 x Ø6 mm Protection class : IP66 Article number : A Certficate: ATEX - Ex II 2GD Ex de IIB T6 + H2 T6 Gb - Ex tb IIIC T85 C IP66 EN EN Explosion-proof thermostat type EJB D8640 The explosion-proof room thermostat is suitable for gas group IIC with EN/IEC test certificate. This explosion-proof room thermostat consists of a steel or stainless steel casing. Cable gland M20x1.5 HAWKE type 501/453/O. The sensor is located in a perforated guard. The capillary thermostat is adjustable between 0-40 C. Technical specifications Type : D phase Supplied with : 2 brass cable glands Material : steel casing Setting range : C Ambient temperature : -30 C C Hysteresis : 2 C Switching power : max. 3x400 Volts AC to 3x16A Protection class : IP66 Article number : A Type : D phase Supplied with : 2 brass cable glands Material : stainless steel casing Setting range : C Ambient temperature : -30 C C Hysteresis : 2 C Switching power : max. 3x400 Volts AC to 3x16A Protection class : IP66 Article number : A A Certificate: ATEX - Ex II 2GD Ex d IIC T6 Gb - Ex tb IIIC T110 C Db EN/IEC EN/IEC mm 250 mm 103 mm 112 mm 225 mm 100 mm EJB D8525 EJB D

13 Applications Sinus-Jevi space heaters are suitable for anticondensation, freeze protection and s Different applications can be: - switch boards - control cabinets - tunnel fire systems - heating of (very) small spaces 13

14 Sinus is one of the pioneers in the field of explosion proof heating equipment, today we are still operating at the forefront. We manufacture according to ATEX as well as IECEx and EAC directives. For the production of Ex-proof equipment a PQAN (Product Quality Assurance Notification) is issued by TUV-Nord. Our ISO-9001 and ISO systems are also monitored by this organisation. A E Sinus-Jevi Electric Heating B.V. Aambeeld NT Medemblik +31 (0)