ADAPT Parasol EX a. Installation - Commissioning - Maintenance ADAPT Parasol EX a - m A1, B1

Transcription

1 ADAPT Parasol EX a Installation - Commissioning - Maintenance A1, B1 ADAPT Parasol EX a - m A2 B2 1

2 ADAPT Parasol EX a - m A3 B3 M6 B4 A4 A5 A6, B5 2

3 ADAPT Parasol EX a - m A7, B6 male thread DN (1/2 ) Note that clamp ring couplings require support sleeves inside the pipes. A8, B7 d/2 3

4 ADAPT Parasol EX a - m A9, B8 B A9, B8 C F G H B I C F G H I or SH or SH A10, B9 A B C D E F G H I or SH black white Sensor blue Condens red yellow 0-10V DC red black white 24V 24V G0 G0 24V 24V brown (US=white) blue (US=black) 0-10V DC G0 G0 G G Wiring when not using VOC sensor 2. Wiring when using VOC sensor 4 Sensor Condens Swegon reserves the right to alter specifications. brown (US=white) brown blue grey green blue (US=black) black black white brown white CO2 brown VOC SHoR

5 ADAPT Parasol EX a - m A11, B10 A12, B11 TORX T-25 / 1 x 8 A13, B12 A14, B13 Click! ON 1 2 ON 1 2 5

6 ADAPT Parasol EX a - m A15, B14 A16 B15 A17, B16 6

7 ADAPT Parasol EX a - m A18, B17 A19, B18 7

8 ADAPT Parasol EX a - m Super WISE Next Zone CONTROL Zone MB MB1 RS -485 type Belden 9842 MB id 1 G 24 A B G 24 A B ADAPTER RJ12/WIRE Master/Master with SuperWISE system Modular 6/6 RJ12 Modular 6/6 RJ12 Modular 6/6 RJ MB id 4 Master MB id 8 Master MB id 12 Master Master/Slave with SuperWISE system Modular 6/6 RJ12 Modular 6/6 RJ MB id 4 Master MB id 1 Slave id 1 MB id 2 Slave id 2 BMS RS 485 Master/Slave with BMS sytem Modular 6/6 RJ12 Modular 6/6 RJ MB id 1 Master MB id 2 Slave id 1 MB id 3 Slave id 2 8

9 ADAPT Parasol EX a Installation -Commissioning - Maintenance K factor, sides = k2 = max. flow ADAPT Parasol EX 2 3 k-factor per side Size Nozzle setting per side Side * ** 690 L 1& L 2& M 1& K factor, sides = k1 = min. flow M 2& H 1& H 2& L 1&3 0,253 0, L 2&4 0 0, M 1&3 0,44 0, M 2&4 0 1, H 1&3 0,693 0,693 ADAPT Parasol EX a - m 1290 H 2&4 0 1,825 * ) = k-factor for adjusting the min. flow. ** ) = k-factor for adjusting the max. flow. q i ( ) 2 1 p = [Pa] k q = k p i [l/s] [pi Pa] q [l/s] k = k-factor ADAPT Parasol EX Size Example nozzle setting k pl *** ) k1 k2 690 LLLL LHLH MMMM HHHH LLLL , LHLH , MMMM , HHHH ,04 *** ) All four sides on the unit can be set individually. The designation of the nozzle setting follows the order of figure to the left. k1 = No occupancy flow k2 = Max. occupancy flow k1 / k2 K p = 0.50 / 3.66 OBS! Any change between max. and min. flow will slightly change the nozzle pressure. 9

10 ADAPT Parasol EX Commissioning/checking the airflows Constant pressure in zone with CONTROL Zone or similar zone damper. 1. Check that all the WISE products are energised. T x 8 Nozzle configuration H M L H = M= L= 2. Ensure that all the ADAPT Parasol EX modules have their correct C-factors and minimum and maximum flows preset. Ensure that all are set to the maximum flow commissioning position, (3 blue + 3 red LEDs are lit). 3. Check the flow, compare the maximum flow in the zone, adjust the pressure setpoint until the correct flow is obtained with TUNE Control. If Max. flow is not attained, another zone damper / other zone dampers should be temporarily closed. 4. Measure and record the airflow in the max. position on one ADAPT Parasol EX in the zone. 5. Reset to the min. flow, measure and record the airflow. 6. Set back to maximum flow. 7. Perform the same procedure for all the ADAPT Parasol EX modules in the zone. 8. Reduce the pressure setpoint setting on the zone damper if pressure is required for other zones, e.g. 5 Pa. 9. Commission the remaining zones, following the same procedure. X-shape 10. Check/commission the previous shut-off zones in the same way. 11. Restore the pressure setpoints on all the zone dampers. 12. Identify the reference zone, i.e. the zone with the lowest flow compared with the design maximum flow (e.g. by checking present airflow across each zone damper; using the TUNE Control hand unit). 13. Set the minimum flow on a number of ADAPT Parasol EX modules or use the zone damper for setting the minimum flow so that the ventilation system responds to the simultaneous load. Fan-shape 14. Now adjust the air handling unit s pressure setpoint until the zone damper of the reference zone is 85-90% open, (done by the SuperWISE, if it is used). 15. Restore all the settings and set all the ADAPT Parasol EX modules to normal position. 10

11 ADAPT Parasol EX Sensor module menu: To reach the menu, hold the left-hand and right-hand buttons down for five seconds. With the left-hand button ( ) you advance through the menus. With the right-hand button ( ) you confirm your selection and return to the menu. Press the left-hand button and select: 1. Alarm list 2. Commissioning 6. Return to menu Press the righthand button to confirm your selection 1. Alarm list: See the complete alarm list to the right. 2. Commissioning: There are then six selections in the commissioning menu, (press the left-hand button to advance in the menu). When you have marked a selection, the controller goes directly to that operating mode. 2.1 Min. airflow, holiday/ no occupancy for longer period 2.2 Min. airflow, no occupancy 2.3 Min. airflow, occupancy 2.4 Max. airflow, occupancy 2.5 Open cooling valve 2.6 Open heating valve Press the right-hand button to return to the menu. 1 and 3 are not used if ECOPulse and 2Step are in use 3, 4, 5. Not used. 6. Return to menu Function button Temperature sensor Presence detector Diodes for temperature, commissioning or alarm indication Function button Alarm list for the sensor module Alarm no. Type of alarm Alarm 1 Supply voltage low Alarm 2 Supply voltage critically low Alarm 3 Ext temp missing Alarm 4 Ext temp error Alarm 5 Condensation sensor error Alarm 6 SM temp sensor error Alarm 7 SM button error Alarm 8 CO 2 sensor missing Alarm 9 VOC Error Alarm 10 Low pressure Alarm 17 SM comm error Alarm 18 Slave comm error Alarm 19 Pressure sensor comm error Alarm 20 VOC sensor comm error Alarm 21 No master request (slave) Alarm 22 Slave incompatible version Alarm 25 Heating comfort alarm Alarm 26 Cooling comfort alarm Alarm 27 Temp. Set point overlap alarm Alarm 28 Air quality comfort alarm Alarm 29 Condensation Alarm V Out 1 overload error Alarm V Out 2 overload error Alarm V Out 3 overload error Alarm 41 Slave input common alarm Alarm 42 Slave output common alarm The alarm is displayed by a number of diodes when you have selected Alarm list (1) in the menu. Each diode represents a number as shown in the table above and the numbers should be added up to form an alarm number. Ex. The centremost blue and the two last red diodes are lit (xoxxoo) Diode-indicating function The centremost blue one corresponds to 16, the penultimate red one to 2 and the last red one to 1. The sum of - Green = Ok - Flashing Green = Condensation alarm these is 19, which is the alarm number. - Yellow = Alarm - Green/Yellow = Comfort alarm (not acute) ADAPT Parasol EX - m 3 parallel RJ12 ports (Modbus) for connecting a controller for instance, another sensor module or computer by means of Cable converter USB-RJ12 ON 1 2 Addressing the sensor module. 10 sensor modules can be connected to each master unit. Each one must have its own unique address in order to work. Switch for termination resistance. Set Switch 1 to the ON position for the last sensor module in the loop. 11

12 ADAPT Parasol EX a Installation - Commissioning - Maintenance ADAPT Parasol EX a - m 7 3 ON 1 2 ON Art.no