PATROL SOUNDERS 110/120 db(a) PA 10 / PA 20

Transcription

1 PRODUCTS AUDIBLE SIGNALING DEVICES PATROL SOUNDERS 110/120 db(a) PA 10 / PA 20 PATROL the new generation of sounders. Three dimensional innovation. Safe; an incorrect installation is virtually impossible. Easy; significantly shorter assembly and installation times. Economical; extremely high efficiency and good penetration of acoustical obstacles significantly reduce the required number of sounders. IP 66 IK C 40 C EN 54-3 VdS UL 10 Years Schutzart impact-proof housing operating temperature acoustic penetration external tone selection V DC V DC warranty PRODUCT PA 10 PA 20 DATA Operating range V V V V V V AC Hz DC AC Hz DC Nominal current consumption ma ma ma ma ma ma Sound pressure level 110 db(a) 120 db(a) Sound level reduction max. 12 db via potentiometer Alarm tones 80 / 4 tones are externally selectable Duty cycle 100 % Operating temperature 40 C C Storage temperature 40 C C Relative humidity 90 % Protection system according to EN 6052 IP 66 Protection class II Material PC / ABS blend similar to RAL 3000 (flame red) RAL 7035 (light grey) RAL 9003 (signal white) Cable entry 5x M20 knock-outs on side, 1 knock-out on back Integrated seal with cable entry 6 13 mm (feed-through grommet) Connecting terminals 2.5 mm 2 fine wire with cable end sleeve, AWG 16 Weight 1,060 g 1,050 g 1,200 g 1,090 g 1 Power consumption dependent on operating voltage. OPTIONS/ACCESSORIES I lim t Enclosure fitting Surface gasket Tamperproof sealing Panel mounting kit

2 DIMENSIONS PA 10 PA Ø Ø 9 M20 prepared M20 prepared AUDIBLE SIGNALING DEVICES ARTICLE PA 10 PA 20 VERSION RATED VOLTAGE V AC 24 V AC V DC V AC 24 V AC V DC Standard housing red GL/MED housing red Standard housing grey GL/MED housing grey Article numbers for other voltages and versions on request. ARTICLE PA 10 PA 20 Enclosure fitting For connection (daisy-chaining) of several sounders of the PATROL series Surface gasket Tamper-proof sealing (pack of 4) Panel mount installation kit PATROL Sealing of the sounder installation surface when, e. g. cable entry is executed from the back. Anti-tamper sealing for fasteners of the PATROL devices after installation in order to prevent manipulation of the devices. The PATROL devices are also suitable for panel mounting. This kit consists of a plug connector for the electrical contact, as well as all installation materials

3 PRODUCTS AUDIBLE SIGNALING DEVICES TONE TABLE 15 evacuation alarm Netherlands NEN evacuation alarm Australia AS NFPA 775 Hz Pulsating tone, Australien alert AS1670, ISO , (fast), IMO 3d, Germany KTA3901 evacuation alarm Hz 65, Sweden SS (all-clear signal) 66 67, Germany KTA3901 (all-clear signal) Hz PFEER (general alarm), UK BS (back-up alarm) PFEER (general alarm) Hz 10 s 40 s 10 s Hz Hz 54, Finland (all-clear signal) 1 55, PFEER gas alarm Sweden SS (local warning) 103 Sweden SS (air raid warning) Sweden SS (emergency signal) 107 Germany KTA3901 (evacuation alarm) 420 Hz 109 Australia AS2220, AS1610, AS (fast variable), bell 111 ISO8201 (emergency evacuation signal), USA (evacuation alarm) 470 Hz 112 ISO8201 (emergency evacuation signal) 113 ISO8201 (emergency evacuation signal), sweeping 7s 7s 4 ms 0,7 s Sweden SS (important message (pre-mess)) 4 ms Hz 680 Hz Sweden SS (emergency signal) (fast), Horn Hz Hz Hz 1 P FA N N E N B E R G. C O M 61, general alarm Finland 46 0,85 s 422 Hz 3,75 s (medium), UK BS ,5 s 1600 Hz (fast), UK BS ,6 s, France NFC (fast) 0,3 s 60 0,3 s 0,875 s 0,875 s 13 s 6,5 s 1,8 s 1,8 s 150 ms 150 ms 900 Hz Hz 0,75 s 0,625 s 0,625 s 1450 Hz 0,69 ms 2850 Hz 970 Hz 59 (fast), UK BS Hz 57 fire alarm, UK BS Sawtooth, DIN tone Germany (emergency signal), PFEER PTAP no tone 2 1

4 0, TONE TABLE IMO (telephone call) IMO (leave ship) IMO SOLAS III/50 + SOLAS III/6.4 (general alarm) 122 Alternating tone 123 Alternating tone 124 Singapore 125 Alternating tone 128 Alternating tone 130 UK BS (fire alarm) CONTROL OF THE TONES s s 0.25 s 2000 Hz 0.5 s 3 s 0.5 s 2,5 s 7 s 1025 Hz 2,5 s 0.25 s 0.25 s 2400 Hz 0.5 s 0.25 s EN s 0.25 s s s 1025 Hz DIP-SWITCH EXTERNAL TONE SELECTION (SETTING OF BASIC TONE) C1 C2 C1+C BASIC TONE TONE ON 2 * ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON * factory setting UK BS (fire alarm, railway crossing) UK BS (fire alarm, increased urgency railway crossing) 142 Alternating tone Alternating tone France NFS (fire alarm) Sweden SS Sweden SS Alternating tone (two tone chime) 900 Hz 650 Hz 0,4 s 650 Hz 2 s DIP-SWITCH EXTERNAL TONE SELECTION (SETTING OF BASIC TONE) C1 C2 C1+C BASIC TONE TONE ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON AUDIBLE SIGNALING DEVICES

5 PRODUCTS AUDIBLE SIGNALING DEVICES CONNECTION DIAGRAM X2 -L -L +N +N C1 C2 C1 C2 electrical connection and tone selection through external control of C1 and C2 operating voltage connection N - L + AC: DC: DC + - S2 S2 (by-passing the reverse polarity protection diode) with reverse polarity protection (factory setting) without reverse polarity protection + - AC S3 S1 volume control Note: In order to conform to EN54-3, the volume control must be set to the maximum position S3 tone selection switch S1 (selection of the polarity of the control voltage for C1 and C2) factory setting + CONFORMITY TO STANDARDS The acoustic parameters conform to the European standard DIN EN ISO 7731: Ergonomic alarms for public areas and workplaces acoustic alarms. The requirement for an acoustic alarm signal can be found in the harmonised standards: EN Electrical equipment of machines EN Radiation safety of laser devices, identical to IEC 825 and DIN-VDE 08