AP200 SERIES INTELLIGENT ALARM DEVICES

Transcription

1 Tech Data Sheet D017GB1 Fire Detection /01 AP00 SERIES INTELLIGENT ALARM DEVICES Intelligent AP00 series alarm devices for FX NET fire detection system The intelligent AP00 series alarm devices are used in the FX NET fire detection system. They have been designed to reduce significantly the total cost of installation. Product performance has been optimized to allow the maximum permissible number of devices to be installed on an intelligent loop. Wall mount devices WST-PC-I WST-PC-N The sounders and visual alarm devices are installed in exactly the same manner as an intelligent fire detector. The devices use the B01AP detector base. At final commissioning, the sounder or strobe simply twists into the base and the installation is complete. This simple but effective concept significantly reduces the time and cost of installing audible visual warning devices when compared with previous designs. In addition, fire systems designers benefit from the flexibility of being able to change the type of installed device if the protected building is reconfigured by the occupiers. WSS-PC-I WSS-PC-N Fault finding is also easy. The suspect device is removed with a simple twist action without having to disconnect any loop wiring; a replacement is then mounted into the base. The visual alarm devices VADs are EN- approved as open class devices and sounders are EN- approved.

2 Tech Data Sheet D017GB1 Fire Detection /01 Mechanical dimensions Electrical installation, Base B01AP Wall mount devices 11 1 (+) (+) (-)1 SHIELD FX SLC addressable loop WST-PC-xxx Deep Base BPW-E010 and Waterproof Base WPW-E WSS-PC-xxx Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: Fax: Document Number D017GB1 01

3 Tech Data Sheet D017GB1 Fire Detection /01 Mechanical installation Bases/IP rating Mounting Affix B01 AP base to suitably flat wall or ceiling. Terminate the cable to the appropriate terminals. For surface mount wiring the cable can enter the B01 AP base via the break outs provided. Select the appropriate tone and volume settings via the DIP switch. Locate the main assembly on to the base by rotating until it locks into place. Wall mount: B01AP Base (IP1C) Deep Base BPW-E010 (IP) Waterproof Base WPW-E010 (IP) If the waterproof option is required then the wall gasket must be fitted behind the deep base, and the sealing o-ring fitted after attaching the low profile base. Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: Fax: Document Number D017GB1 01

4 Tech Data Sheet D017GB1 Fire Detection /01 Anti tamper lock The B01 AP base also includes a tamper resistant feature that when activated prevents removal of the unit without the use of a special tool. This method is consistent with the a tamper feature across all devices using this base. This prevents the device being turned to enable its release. Wall mount: Examples: Address setting x x1 Address setting x x1 Note! Address setting 01 is used with the FX- LC loop controller. Volume and tone setting (WST-, WSS-) Volume setting is selected by SW and SW7 of the 8 way DIP switch (see table Volume settings). The appropriate tone set is selected by SW1 to of the 8 way DIP switch (see table Tone settings). The nd stage tone (related to the 1 st stage tone) is controlled by the fire panel via the protocol. Address setting The address setting in the devices is simply done with two rotary decimal switches, thus having a range of 1 1. In addition the panel can distinguish between detector addresses, I/O-module addresses and sounder addresses, and thus providing a total address capacity per loop of and 01, altogether 18 addresses. Two rotary switches are located either side of the dip switch unit. 7 Volume settings x10 SW SW7 Volume setting OFF OFF High OFF ON Medium ON OFF Low ON ON Low OFF = 0, ON = 1 1 ON ON Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: Fax: Document Number D017GB1 01

5 Tech Data Sheet D017GB1 Fire Detection /01 Tone settings DIP setting O=Off/1=On SW 1,,,, No Pattern Nominal Frequency Switching Frequency Description Standard 0,0,0,0,0 1 Alternating /0 Hz French Fire Sound (100ms/00ms) AFNOR NFS ,0,0,0,0 Alternating 800/70 1Hz BS8 Pt1 8 0,1,0,0,0 Alternating 800/70 Hz Alternating tone BS8 Pt1 telecoms FP ,1,0,0,0 Alternating 00/00 Hz Alternating High Frquency 10 0,0,1,0,0 Alternating 00/100 Hz Security Alarm 10 1,0,1,0,0 Alternating 88/ Hz 8 0,1,1,0,0 7 Continuous 0 All Clear 1 1,1,1,0,0 8 Continuous 70 BS8 Pt1 0,0,0,1,0 Continuous 100 1,0,0,1,0 10 Continuous 80 HF Continuous 0,1,0,1,0 11 Sweep Raising from 10Hz to 1000Hz in 10 seconds, then 0 seconds at 1000Hz, then falling from 1000Hz to 10Hz in 10 seconds, then 0 seconds at 10 Hz, then repeating. Total period 80 seconds. Gasalarm Tone 1,1,0,1,0 1 Intermittent 0 0.s on,0.s off AS0 alert tone AS0 1 0,0,1,1,0 1 Sweep s off,.7s off AS0 evacuate tone AS0 1 1,0,1,1,0 1 Intermittent 0.Hz 10ms on, 10ms off Swedish Alarm Tone 7 0,1,1,1,0 1 Intermittent Hz 0.s on, 1s off Intermittent Tone BS8 Pt1 8 1,1,1,1,0 1 Intermittent 70 0.Hz 1s on, Backup alarm LF & 1s off BS8 Pt1 BS8 Pt1 8 0,0,0,0,1 17 Intermittent 80 1Hz Backup alarm HF & BS8 Pt1 nd Tone BS8 Pt1 10 1,0,0,0,1 18 Intermittent 70 1Hz 00ms on, 00ms off BS8 Pt1 BS8 Pt1 8 0,1,0,0,1 1 Intermittent 0 0.Hz (0.s on, 0.s off)*, 1.s off ISO ,1,0,0,1 0 Continuous 800 Hz 10ms on, 100ms off BS8 Pt1 0,0,1,0,1 1 Sweep (0.s on, 0.s off)*, Temporal ISO801 1.s off Evacuation tone Temporal 1 1,0,1,0,1 Sweep Hz 1s on, Evacuate, DIN tone & 0.01s off PFEER DIN, PFEER 0 0,1,1,0,1 Sweep Hz Fast Sweep Vds Vds 10 1,1,1,0,1 Sweep sec off.sec on Slow whoop evacuate Netherlands NEN 7 8 0,0,0,1,1 Sweep Hz LF buzz BS8 Pt1 BS8 Pt1 8 1,0,0,1,1 Sweep Hz Fast sweep LF BS8 Pt1 BS8 Pt1 8 0,1,0,1,1 7 Sweep Hz Medium sweep LF buzz BS8 Pt1, BS8 Pt1 VdS 8 Vds 1,1,0,1,1 8 Sweep Hz High frequency buzz 10 0,0,1,1,1 Sweep Hz Fast whoop 8 1,0,1,1,1 0 Sweep Hz rise 1 s, 00 stable s, fall 1s Siren style tone 8 0,1,1,1,1 1 Sweep Hz 8 1,1,1,1,1 Sweep Hz 10 nd Stage Tone Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: Fax: Document Number D017GB1 01

6 Tech Data Sheet D017GB1 Fire Detection /01 Sounder current consumption Typical current consumption DIP setting O=Off/1=On No Wall mount devises SW 1,,,, (WSS) (WSS) (WSS) High Medium Low 0,0,0,0,0 1.0/../.8 1./. 1,0,0,0,0./8.7./. 1./.7 0,1,0,0,0./8..8/.1 1./.7 1,1,0,0,0./8../. 1.7/.0 0,0,1,0,0.7/10.0./. 1.8/.1 1,0,1,0,0./../.8 1./.7 0,1,1,0,0 7.0/8../.8 1./.7 1,1,1,0,0 8.8/8.1./. 1./.7 0,0,0,1,0.8/8.1./. 1./.8 1,0,0,1,0 10./8..7/.0 1./.8 0,1,0,1,0 11./8.8./.8 1./.7 1,1,0,1,0 1./../. 1.1/. 0,0,1,1, /1.7./. 1.7/.0 1,0,1,1,0 1.0/8../.7 1./. 0,1,1,1,0 1.8/8.1./. 1./.7 1,1,1,1,0 1.8/8.1./. 1./.7 0,0,0,0,1 17./8..7/.0 1./.8 1,0,0,0,1 18.8/8.1./. 1./.7 0,1,0,0,1 1./7..1/. 1./. 1,1,0,0,1 0./8../. 1./. 0,0,1,0, /1..1/. 1./. 1,0,1,0,1 10./1../. 1.7/.0 0,1,1,0,1.0/8../. 1./. 1,1,1,0,1 10./1../.8 1.7/.0 0,0,0,1,1.0/7../. 1./. 1,0,0,1,1./7.8./.8 1./.7 0,1,0,1,1 7.1/8..8/.1 1./.7 1,1,0,1,1 8./8../. 1.8/.1 0,0,1,1,1./8.7./.8 1./. 1,0,1,1, /1../.7 1.7/.0 0,1,1,1,1 1./8..7/.0 1./.7 1,1,1,1,1./8../. 1./. Note! For Isolated variants add 0.1mA to high, medium, low values above. Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: Fax: Document Number D017GB1 01

7 Tech Data Sheet D017GB1 Fire Detection /01 7 Technical data Wall Mount Devices WSS-PC-xxx WST-PC-xx Description Sounder VAD VAD Operating voltage 1 to VDC(isolation) (VDC typical) 1 to VDC (non isolation) (VDC typical) Quiescent current 0µA Max current consumption (sound).0ma (isolation) (High Volume Tone 8@ V) Max current consumption (sound) 8.8mA (non isolation) (High Volume Tone 8@ V) Sound Output to EN- db(a)±db (High Volume Tone 8@ V) EN- coverage See installation instructions Beacon Flash Rate 0, / 1 Hz Max current consumption/strobe (isolation) WST-PC-***.mA Max current consumption/strobe (non isolation) WST-PC-***.1mA Operating Temperature - to 70 C Relative Humidity Up to % (±%) non-condensing IP Rating IPC (with B01 AP base) IP (with Deep base BPW-E10) IP (with Waterproof base WPW-E10) Colour Clear lense Weight g 170g Terminal Size max.mm Number of Tones Volume Setting High, Medium, Low Product codes WSS-PC-I, isolation WSS-PC-N, non isolation WST-PC-I, isolation WST-PC-N, non isolation FFS07117 FFS07117 FFS FFS Bases IP rating Product codes B01AP IP1 FFS BPW-E010 IP FFS07117 WPW-E010 IP FFS07117 Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: Fax: Document Number D017GB1 01

8 .0 METRES DP 1. METRES DP 1.7 METRES DP 1.7 METRES DP 1.77 METRES DP Tech Data Sheet D017GB1 Fire Detection /01 8 O-Class Coverage Shape WST-PC-x: INSTALLATION_SURFACE 0 0 INSTALLATION_SURFACE INSTALL_HEIGHT INSTALL_HEIGHT 1.8 METRES DP 1. METRES DP 0 FLOOR_LEVEL R0.88 METRES DP FLOOR_LEVEL WSS-PC-x: SCALE 0,00 INSTALLATION_SURFACE 0 0 INSTALLATION_SURFACE INSTALL_HEIGHT INSTALL_HEIGHT 1.80 METRES DP 1. METRES DP 0 FLOOR_LEVEL R0.7 METRES DP FLOOR_LEVEL Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: Fax: Document Number D017GB1 01