SOUNDER WITH BEACON FOR FIRE DETECTION PANEL

Size: px

Start display at page:

Download "SOUNDER WITH BEACON FOR FIRE DETECTION PANEL"

Gervais Edmund Miller
5 years ago
Views:

ΒS-/ SOUNDER WITH BEAC FOR FIRE DETECTI PANEL OPERATI VOLTAGE MAXIMUM CSUMPTI MAXIMUM SOUND OUTPUT inm BEAC ΤYPE OF APPLICATI ENVIRMENT MOUNTING COVERAGE (y) MOUNTING HEIGHT (x) COVERAGE VOLUME CODE

1 ΒS-/ SOUNDER WITH BEAC FOR FIRE DETECTI PANEL OPERATI VOLTAGE MAXIMUM CSUMPTI MAXIMUM SOUND OUTPUT inm BEAC ΤYPE OF APPLICATI ENVIRMENT MOUNTING COVERAGE (y) MOUNTING HEIGHT (x) COVERAGE VOLUME CODE COVERAGE VOLUME FLASH RATE FLASH COLOUR DEGREES OF COVER PROTECTI PRODUCED IN ACCORDANCE WITH OPERATI TEMPERATURE RANGE RELATIVE HUMIDITY CSTRUCTI MATERIAL EXTERNAL DIMENSIS TYPICAL WEIGHT GUARANTEE GENERAL This device is Visual Alarm Devices (VAD) for fire detection panels that offer a strong sound output and an optical warning with a beacon. The strong sound and the optical warning beacon cover many square metres. It features two inputs (N, N) for the production of two different sounds. This device can co-operate with any fire detection panel (BSR-0, BSR-, BS-, BS-, BS-, BS-). Installation and Connection. First, remove the retaining screw, place a flat blade screwdriver in the holes of the plastic hooks and remove the plastic cover (Image on page ).. Remove carefully the beacon connector (Image on page ).. Use the supplied mounting parts to install the siren s base at a height of. metres from the floor (figure on page ). Place the plastic plugs and fasten the screws to the mounting holes. Attention!! Make sure that the siren s base is installed upwards as shown in figure on page.. Place the caps and make a hole in the center using a small screwdriver. Pass Page from ΤΕCHNICAL CHARACTERISTICS -8V DC.W 9dB (sound effect ) Power LED Τype Α Wall m around the siren at an angle of 80.m max W-.- 8.m³ (max) Hz (Switchable to 0. Hz) Red IPC EN -: 00 +Α:00 +Α:00, EN -: 00 o 0 to 0 C Up to 9% Bayblend FR00, transparent polycarbonate x x 00 mm 0gr. years Thank you for your trust in our products Olympia Electronics - European manufacturer through the caps the cables to connect the device.. The (+N or the +N) terminal block is connected to the (+) output of Alarm- or Alarm- of the panel and the (-) of the terminal block is connected to the (-) output of Alarm- or Alarm- of the panel. Accordingly connect in parallel all the sirens. (The maximum number of sirens depends on the type of the panel).. To select various sound effects use the dipswitch, and and choose the diserable sound effect, according to tables and on page. 7. For LED effect variation use the dipswitch (Table ) on page. On the last siren of the line, we must connect in parallel with its power cables, the terminal resistor that was removed from the alarm contacts of the panel. 8. Reinstall the beacon connector (step ). Refit the plastic cover until the plastic hooks are securely attached (step ) and fasten the retaining screw (torque 0.Nm). Attention!! Make sure that the siren s cover is installed in the correct orientation. 9. Test the device after installation.

2 UP Image UP Image +N +N W-x-y TO FIRE DETECTI PANEL Image D i p s w i t c h s i r e n a n d b e a c o n selections x=.m y=m VAD y x y Figure W -Wall Mounted Device DSW TABLE LED effect 0. sec.9 sec OFF (0. Hz) 0. sec 0.9 sec OFF ( Hz) NOTE!!! After finishing the installation, place the SEAL sticker as shown in the picture. Page from

3 DSW Nr 0 970Hz continuous BS89-:00 - evacuate BS89 Part Sound effect 970Hz (sec - sec OFF) From 00Hz to 00Hz in sec From 00Hz to 00Hz in. sec - 0. sec OFF 800Hz - 970Hz alternate at Hz Intermittent 80Hz (0. sec - 0. sec OFF) 970Hz (0. sec 970 Hz OFF x times +. sec OFF) 80Hz (0. sec 80 Hz OFF x times +. sec OFF) TABLE Fire Detection Panel connection to +N Tone in accordance to: BS89-:00 - alert BS89 Part 988 BS89-:00 - DIN -Tone DIN0 Part NEN7 (Netherlands) BS89-:00 ISO80 High Frequency ISO80 Low tone - US Temporal Tone LF ISO80 High tone - US Temporal Tone HF db ma DSW Nr 0 7 Sound effect 970Hz ( sec - sec OFF) 970Hz continuous From 00Hz to 00Hz in. sec - 0. sec OFF From 00Hz to 00Hz in sec Intermittent 80Hz (0. sec - 0. sec OFF) 800Hz - 970Hz alternate at Hz 80Hz (0. sec 80 Hz OFF x times +. sec OFF) 970Hz (0. sec 970 Hz OFF x times +. sec OFF) TABLE Fire Detection Panel connection to +N Tone in accordance to: BS89-:00 - alert BS89 Part 988 BS89-:00 - evacuate BS89 Part 988 NEN7 (Netherlands) BS89-:00 - DIN -Tone DIN0 Part ISO80 High Frequency BS89-:00 ISO80 High tone - US Temporal Tone HF ISO80 Low tone - US Temporal Tone LF db ma Page from

4 WARRANTY Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which accompanies each product. This warranty ceases to exist if the buyer does not follow the technical instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully agreed to them in writing. Products that have been damaged can be returned to the premises of our company for repair or replacement, as long as the warranty period is valid. Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the buyer the transportation cost. HEAD OFFICE 7nd km. O.N.R. Thessaloniki-Katerini P.C. 000 P.O. Box 0 Εginio Pierias Greece info@olympia-electronics.gr Certification The sounder with beacon BS-/ is certified from H.E.E.Q.A.C. Also H.E.E.Q.A.C. controls the production under CPR number: BS-/ SOUNDER WITH BEAC CPR-0 EN--: 00 +Α:00 +Α:00 EN--: 00 KOLINDROS PIERIAS 00 GREECE Page from

5 Figure which shows the correct positioning of the base Horizontal line parallel with the ceiling Wall hole diameter mm Page from

AP200 SERIES INTELLIGENT ALARM DEVICES

AP200 SERIES INTELLIGENT ALARM DEVICES Tech Data Sheet D017GB1 Fire Detection /01 AP00 SERIES INTELLIGENT ALARM DEVICES Intelligent AP00 series alarm devices for FX NET fire detection system The intelligent AP00 series alarm devices are used