Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK

Transcription

1 Schedule of ccreditation United Kingdom ccreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK BSI ssurance UK Limited ccredited to BSI Kitemark Court avy venue Knowlhill Milton Keynes MK5 8PP Sales Enquiry Tel: +44 (0) Fax: +44 (0) Sales Enquiry Certification.Sales@bsigroup.com BSI Website: Regulatory Contact: Ms Maria Crane Tel: +44 (0) maria.crane@bsigroup.com Laboratory locations: below s covered by the organisation and their relevant activities details ctivity code ddress Kitemark House Maylands venue Hemel Hempstead Hertfordshire HP2 4SQ Local contact Maria Crane Tel: +44 (0) Fax: N/ maria.crane@bsigroup.com Website: Polymeric products; Taximeters; Skidresistance testers; Protective headwear; Eye protection; Respiratory protection devices; Latex products; Fire detection & fire alarm systems; Environmental testing; Lighting & photometry; ddress BSI Holywell Park shby Road Loughborough Leicestershire LE11 3Q Local contact Maria Crane Tel: +44 (0) Fax: +44 (0) maria.crane@bsigroup.com Website: Gas ppliance Testing; Electrical Safety; Medical equipment; Electronic equipment & components; Electrical components; Electrical equipment Site activities performed away from the locations listed above: details ctivity code Suitable commercial and industrial premises and sites Portable fire extinguishers C Flexible Scope The laboratory is accredited to ISO/IEC17025:2005 for testing activities in accordance with the standards highlighted in the schedule. This may also include tests on the same or similar product types against standards, or customerspecified methods that are not specifically listed in this Schedule, providing that: (1) The method or standard does not introduce new principles of. (2) The method or standard does not require s to be made outside the parametric boundaries defined in this Schedule. Information about flexible scopes of accreditation is available in UKS document LB39 and E document E-2/05. ssessment Manager: WC1 Page 1 of 46

2 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ETIL OF CCREITTION POLYMERIC PROUCTS Plastics piping systems for water supply, and for drainage and sewerage under pressure. imensional Load: tension and compression Impact Pressure Thermal stability Impact BS EN : :2013 Excluding clauses 5.3 and 8.2 Table 5 (MFR and OIT only) BS EN :2003 Excluding clauses 5.6 and 8.2 Table 6 (MFR and OIT only) BS EN :2003 Plastics piping systems. Polyethylene (PE) pipes and fittings for water supply imensional Temperature / Pressure Physical Properties BS ISO :2007 BS ISO : :2014 Plastics piping systems for the supply of gaseous fuels imensional Temperature Pressure Physical Properties Markings BS ISO ::2014 BS ISO :2014 Excluding: Clause 7.2 Table 4 (RCP) Clause 8.2 Table 6 (OIT and MFR) BS ISO :2014 Plastics Piping Systems For Soil nd Waste ischarge (Low nd High Temperature) Within The Building Structure imensional Load: bending Impact Pressure Thermal stability BS EN 1055:1996 BS EN :2000 Excluding clauses 4.3, 4.5 and 8.1 Table 13 (MFR only) and 9 Table 16 (Long term performance of TPE seals only) BS EN :2000 Excluding clause 9 Table 20 (Long term performance of TPE seals only) BS EN :2000 Excluding clauses 4.3, 4.5 and 7.1 Table 10 (MFR only) and 8 Table 13 (Long term performance of TPE seals only) BS EN :2000 Excluding clause 9 Table 19 (Long term performance of TPE seals only) BS EN :2000 Excluding clause 9 Table 20 (Long term performance of TPE seals only) ssessment Manager: WC1 Page 2 of 46

3 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited POLYMERIC PROUCTS (cont d) Hot nd Cold Water Pipes imensional Endurance Impact Pressure BS :2010 excluding Clauses 6.5 Cyclic Pressure, 6.6 Opacity and 6.7 Oxygen Permeability BS :2010 BS :2010 Pvc-U Pressure Pipes nd Fittings imensional Load: tension and compression Impact Pressure Thermal stability BS EN ISO :2009 Excluding Clause 4.2 ensity BS EN ISO :2009 Excluding Clauses 4.2 ensity and 8.2 Crush Tests BS EN :2000 Excluding clause 4.3 White Upvc Plastic With Welded Corner Joints - Materials Type imensional Load: bending and tensile Thermal stability Impact (Non-instrumented method only) BS EN 12608:2003 Excluding clause BS 7619:1993 BS EN ISO 179-1:2001 Sharps Containers imensional Impact BS EN ISO 23907:2012 S 4031:1993 Cold Water Storage nd Feed nd Expansion Cisterns nd Lids, Polyolefin Construction requirements Endurance Impact Mass Tensile strength BS 4213:2004 ssessment Manager: WC1 Page 3 of 46

4 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited POLYMERIC PROUCTS (cont d) Conduits nd Fittings For Electrical Installations Metallic nd Non-Metallic Rigid Plain Conduit Of Insulating Material Construction requirements imensional Load: tension and compression Pressure Thermal stability BS :1970 BS 4662:2006 BS EN :1994 BS EN :2004 (superseded) BS EN :2008 BS EN :2004 BS EN :2004 BS EN :2004 IEC 60670:1989 (Withdrawn) IEC :1990 IEC :1993 Official Identification Ear Tags For Cattle, Sheep nd Goats Mechanical & tests PS 44:2009 Excluding clause PS 66: Corr 1:2009 Excluding clause 4.3 Polymeric Products Hardness Rubbers (Natural & synthetic) IRH (Range ) BS ISO 48:2010 BS 903 Part 26:1995 (withdrawn) Plastics & Rubbers Shore (Range ) BS Method 365B:1981 BS EN ISO 868:2003 ENGINEERING INUSTRIL PROUCTS Galvanised Products etermination of galvanising mass per unit area BS EN ISO 1460:1995 Manhole Covers, Road Gully Gratings, Frames nd Linear rainage (Classes To ) Construction requirements imensional BS EN 124:1994 BS EN 1433:2002 PS 26:1998 ssessment Manager: WC1 Page 4 of 46

5 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ENGINEERING INUSTRIL PROUCTS (cont d) Portable Fire Extinguishers Capacity Construction requirements imensional Electrical resistance Finish Impact Mass Resisitance to shock and mechanical damage Retention of charge following partial discharge Pressure Thermal stability Tamping ischarge Corrosion resistance BS EN 3:1996 Excluding Part 1, Clause 7, Part 2, Clause 4, Part 3, Clause 11, Part 5, Clause BS EN 3-7: :2007 Excluding Clause 9 BS EN 3-10:2009 nnex C, Reports only BS EN :2007 Excluding clause 8.2 BS 6165:2002 Clauses 4.1, 4.2, 5.1, 5.2, 5.3, 5.4, 5.5, 5.6, 5.7, 5.8, 5.9, 6.2, 7.1, 7.2, 7.3, 7.4, 7.5 and 9. Fixed firefighting systems - Hose systems - Hose reels with semi-rigid hose Construction requirements imensional Pressure BS EN 671-1:2012 Excluding nnex C BS EN 671-1:1995 (Withdrawn) Excluding clause 9.2 Fixed firefighting systems - Hose systems - Hose systems with lay-flat hose Construction requirements imensional Pressure BS EN 671-2:2012 Fire-fighting hoses. Nonpercolating layflat hoses for fixed systems imensional Temperature Pressure Marking BS EN 14540:2014 Specification for underground fire hydrants and surface box frames and covers Construction requirements imensional BS 750:2012 ssessment Manager: WC1 Page 5 of 46

6 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ENGINEERING INUSTRIL PROUCTS (cont d) Pillar fire hydrants Construction requirements imensional Marking BS EN 14384:2005 Fire hydrant systems equipment - Specification for landing valves for wet risers Construction Requirements imensional Marking BS :1987 inc. amd 1, excluding clauses 4.3, 6, 8, 18, 19, 22, 23, 24, 26 and 27 Fire hydrant systems equipment - Specification for landing valves for dry risers Construction Requirements imensional Marking BS :1987 inc. amd 1, excluding clauses 5, 7 and 17 Fire hydrant systems equipment - Specification for Inlet breechings for dry riser inlets Construction Requirements imensional Marking BS :1975 inc. amd 1, excluding clauses 4.3, 4.4 and 10 Specification for fire hose couplings and ancillary equipment imensional Pressure Marking BS 336:2010 Semi-Rigid Hose Pressure imensional BS EN 694:2014 Lay-flat hoses imensions BS 6391:2009 Clause 6 Mass BS 6391:2009 Clause 7 Hydrostatic pressure BS 6391:2009 Clause 8.1 dhesion BS 6391:2009 Clause 8.2 Moisture absorption BS 6391:2009 Clause 8.3 Flexibility BS 6391:2009 Clause 8.4 Heat aging BS 6391:2009 Clause 8.5 Hot surface resistance BS 6391:2009 Clause 8.6 brasion resistance BS 6391:2009 Clause 8.8 Oil resistance BS 6391:2009 Clause 8.9 Hose assembly couplings & BS 6391:2009 Clause 10.3 only leakage checks Markings BS 6391:2009 Clause 11 ssessment Manager: WC1 Page 6 of 46

7 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ENGINEERING INUSTRIL PROUCTS (cont d) Hose Clamps (Worm rive Type) Construction requirements imensional Finish: coating thickness Load: torque BS 5315:1991 Surface boxes, guards and underground chambers for the purposes of utilities. Specification for surface boxes Construction requirements imensional BS :2011 Valves (Engineering) General: Construction requirements imensional Finish Pressure BS EN 12266:Part 1:2003 BS EN 12266:Part 2:2002(E) Excluding nnex B2, Clause 4 Table ref to: nti Static esign at 12V nti Static esign at 100V Fire Test esign ELECTRIC N HYRULIC LIFT COMPONENTS: Electrical Tests Landing door locking devices ppendix F.1 of standards BS EN 81-1:1998 Environmental Tests Safety Circuits ppendix F.6 of standards BS EN 81-1:1998 BS EN 81-2:1998 TXIMETERS Electronic taximeters Bench tests for distance and time Environmental Supply voltage variation BS EN 50148:1996 (excluding clauses to ) Transport for London Public Carriage Office Taximeter Specification (1) 2006 ssessment Manager: WC1 Page 7 of 46

8 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited SKI-RESISTNCE TESTERS Comparative testing BS :1989 Clause 5.2 only BS : :2013 BS : :2013 BS : :2013 BS EN :2009 clause 7.3 and nnex BS EN :2011 Clause 6 and nnex.3 only PROTECTIVE HEWER Mechanical, Physical and Practical Tests Visual Inspection Industrial Safety Helmets Excluding Molten metal splash BS EN 397:1995 (withdrawn) BS EN 397:2012 Industrial Bump Caps Roller Skaters, Skateboards, Pedal Cyclists Helmets Helmets For Equestrian ctivities Helmets For Canoeing nd White Water Sports Protective Helmets For Vehicle Users BS EN 812:1998 (withdrawn) BS EN 812:2012 BS EN 1078:1997 (withdrawn) BS EN 1078:2012 BS EN 1384:1997 (withdrawn) BS EN 1384:2012 PS 015:1998 (withdrawn) PS 015:2011 BS EN 1385:1998 (withdrawn) BS EN 1385:2012 ECE Reg excluding visors BS 6658:1985(1995) ustralian standard: S/NZ 1698:2006 Cricketers Helmets BS 7928:1998 Riot Helmets PS 017:1995 Excluding clause 10.1 Helmets For irborne Sports Helmets For lpine Skiers BS EN 966:1996 (withdrawn) BS EN 966:2012+1:2012 BS EN 1077:1996 (withdrawn) BS EN 1077:2007 ssessment Manager: WC1 Page 8 of 46

9 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited PROTECTIVE HEWER (cont d) Mechanical, Physical and Practical Tests Visual Inspection Protective Headware for UK Police Batch / udit testing only (Penetration testing equipment, Impact drop tower and dimensional equipment) Publication Number 21/04 PSB Protective Headware Standard for UK Police 2004 EYE PROTECTION Eye Protectors For Motor Cyclists nd Racing Car rivers Mechanical & Optical BS 4110:1979 (Withdrawn) S 1609:1981 Surface Swimming Goggles Mechanical Tests BS 5883:1996 Personal & Industrial Eye Protection Mechanical and Optical tests BS EN 166:2002 excluding clauses and EN 166:2001 BS EN 167:2002 Excluding clause 4.2.1, 8 BS EN 168:2002 Excluding clause 3.1 & 4, 16 Welding Eye Protectors BS EN 175:1997 ssessment Manager: WC1 Page 9 of 46

10 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited RESPIRTORY PROTECTION EVICES Mechanical, physical and practical performance tests including visual inspection and marking Half Masks nd Quarter Masks For Respiratory Protective evices BS EN 140:1999 Particle Filters Used In Respiratory Protective Equipment BS EN 143:2000 Filtering Half Masks To Protect gainst Particles BS EN 149: :2009 Full Face Masks BS EN 136:1998 Self-contained open-circuit compressed air breathing apparatus with full face mask BS EN 137:2006 Light uty Compressed ir Line Breathing pparatus Incorporating Helmet Or Hood Excluding below zero use and SF6 test BS EN 1835:2000 Continuous flow compressed air line breathing apparatus Excluding Hood material testing and SF6 test BS EN 14594:2005 Excluding clause ssessment Manager: WC1 Page 10 of 46

11 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited COMPLEX RESPIRTORY PROTECTION EVICES Visual Inspection Mechanical Strength Conditioning Practical Breathing Resistance Gas Capacity Filter Penetration, Clogging Strength of ttachment etc. Powered Particle Filtering evices Incorporating Helmets Or Hoods Excluding SF6, NOX, Hg, X and SX Tests BS EN 12941: :2008 Excluding Clauses , and Powered Filtering evices Incorporating Full Face Masks, Half Masks nd Quarter Masks Excluding SF6, NOX, Hg, X and SX Tests BS EN 12942: :2008 Excluding Clauses , and Gas Filters and Combined Filters Excluding NOX, Hg, X and SX Tests BS EN 14387: :2008 Excluding clause Valved filtering half masks to protect against gases or gases and particles Excluding X and SX tests BS EN 405: :2009 LTEX PROUCTS Natural Rubber Latex Condoms irburst imensional Freedom from holes Freedom form visible defects Package integrity BS EN ISO 4074: :2009 Clauses 5, 6, 8, 9, 10,11 only Single Use, Sterilized Medical Rubber Gloves Freedom from holes imensional Force at break BS EN 455-1:2000 BS EN 455-2:2000 (Withdrawn) BS EN 455-2:2009 excluding clause Labelling BS EN 455-3:2006 Clause 4.6 only ssessment Manager: WC1 Page 11 of 46

12 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited FIRE ETECTION & FIRE LRM SYSTEMS Control & Indicating Equipment Functionality, Mechanical, and Physical Testing Verification of design requirements BS EN 54-2:1997 inc. amd 1& 2 BS EN :1996 BS EN :1993 (withdrawn) BS EN :1996 BS EN :1997 BS EN :2002 Electrical utomatic Control & elay Panels Functionality, Mechanical, and Physical Testing Verification of design requirements BS EN :2003 excluding clause 9.5 BS EN 60529:1992 IEC :1981 Heat etectors Functionality, Mechanical, and Physical Testing Verification of design requirements BS EN 54-5:2001 Class, B & C excluding clause 5.13 BS EN :1996 BS EN :1993 (withdrawn) IEC :1981 IEC :1988 (withdrawn) Heat larms Functionality, Mechanical, and Physical Testing Verification of design requirements BS :2003 Class & B excluding clause 5.13 BS EN 60065:2002 BS EN :2002 BS EN :2006 BS EN :1996 Manual Call Points Functionality, Mechanical, and Physical Testing Verification of design requirements BS EN 54-11: 2001 inc. amd 1 excluding Clause 5.13 BS EN :1996 BS EN :1993 (withdrawn) BS EN :1993 BS EN :1996 BS EN :1993 IEC :1988 (withdrawn) Power Supply Equipment Functionality, Mechanical, and Physical Testing Verification of design requirements BS EN 54-4:1998 inc. amd 1 & 2 BS EN :1996 BS EN :1993 (withdrawn) BS EN :1996 BS EN :1997 BS EN :2002 ssessment Manager: WC1 Page 12 of 46

13 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited FIRE ETECTION & FIRE LRM SYSTEMS (cont d) Smoke larm evices Functionality, Mechanical, and Physical Testing Verification of design requirements BS EN 14604:2005 excluding Clause 5.10 & 5.15 BS EN :1996 BS EN 60065:2002 BS EN :2006 BS EN :1996 Smoke etectors Functionality, Mechanical, and Physical Testing Verification of design requirements BS EN 54-7:2001 excluding Clause 5.12 & 5.18 BS EN :1996 BS EN :1993 (withdrawn) BS EN :1996 BS EN :1993 IEC :1988 (withdrawn) System Components Compatibility Functionality, Physical Testing Verification of design requirements BS EN 54-13:2005 Excluding Section 5.5 and section Sounders Functionality, Mechanical, and Physical Testing Verification of design requirements BS EN 54-3:2001 inc. amd 1 & 2 excluding Clause 5.11 BS EN :1996 BS EN 60529:1992 BS EN :1993 (withdrawn) BS EN :1993 BS EN :1996 BS EN :1993 IEC :1981 Voice alarm control and indicating equipment Functionality, Mechanical, and Physical Testing Verification of design requirements Marking BS EN 54-16:2008 BS EN :1996 EN :2007 EN :2006 EN :2005 EN :1997 Excluding: - EMC - Software ssessment Manager: WC1 Page 13 of 46

14 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited FIRE ETECTION & FIRE LRM SYSTEMS (cont d) Short-circuit isolators Functionality, Mechanical, and Physical Testing Marking BS EN 54-17:2005 BS EN :1996 EN :2007 EN :2007 EN :2006 EN :2009 EN :2005 EN :1997 Excluding: - SO2 - EMC - Software Input/output devices Functionality, Mechanical, and Physical Testing Marking BS EN 54-18:2005 BS EN :1996 EN :2007 EN :2007 EN :2006 EN :2009 EN :2005 EN :1997 Excluding: - SO2 - EMC - Software Fire alarm devices. Visual alarm devices Functionality, Mechanical, and Physical Testing BS EN 54-23:2010 BS EN :1996 EN :1999 EN 60529:1991 EN :2007 EN :2007 EN :2006 EN :2009 EN :2005 EN :1997 Excluding: - SO2 - EMC - Software ssessment Manager: WC1 Page 14 of 46

15 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ENVIRONMENTL TESTING Electrical, Electronic nd Mechanical Components: ynamic Tests utomotive Connect-Ors, Capacitors, Circular Connectors, Coaxial Connectors, Printed Circuit Connectors Resistors, Switches, Transformers, Electrical, Electronic nd Mechanical Equipment Control Units, Communications Equipment, Computers, igital Equipment, Medical Equipment, Television Sets, Video Recorders, Fire etection & Fire larm Systems Vibration - Sinusoidal Horizontal and vertical (ambient temperature) Electrodynamic vibrator Freq range Hz Max peak thrust: 13.3 kn Max pk/pk displacement: 50.8 mm Max item mass 340 Kg Max slip table size: 750 x 750mm Vibration - Random Horizontal and vertical (ambient temperature) Electrodynamic vibrator Freq range Hz RMS thrust: 8 kn Max pk/pk displacement: 50.8 mm Max item mass 340 Kg Max slip table size: 750 x 750 mm BS EN 54-2:1997 Clauses 15.7 and BS EN 54-4:1997 Clauses 9.8 and 9.15 BS EN :1996 IEC 60068:Part 2.6:1982 MIL-ST 202F:1981:Method 201 (withdrawn) Method 204 MIL-ST 810E:1989 Method EF STN :1999 Test M1 EF STN 07-55:1975 Test 1 BS 2011:Fd:1973(1984) BS 2011:Fda:1973(1984) BS 2011:Fdb:1973(1984) BS 2011:Fdc:1973(1984) IEC :1973 IEC :1973 IEC :1973 IEC :1973 IEC :1995 EF-STN 07-55:1975:Test 2 MIL-ST 810E:1989: Method (withdrawn) EF STN 00-35:1999 Test M1 Bump (ambient temperature) Electrodynamic vibrator Max severity 100 g Max item mass 250 Kg Max duration 30 ms (severity dependent) Max item size: 1 x 1 x 2 m Table size: 750 x 750 mm BS EN :1993 IEC :1987 EF-STN 07-55:1975:Test 5 EF-STN 00-35:1999: Test M12 ssessment Manager: WC1 Page 15 of 46

16 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ENVIRONMENTL TESTING (cont d) utomotive Connectors, Capacitors, Circular Connectors, Coaxial Connectors, Printed Circuit Connectors Resistors, Switches, Transformers, Electrical, Electronic nd Mechanical Equipment Control Units, Communications Equipment, Computers, igital Equipment, Medical Equipment, Television Sets, Video Recorders, Fire etection & Fire larm Systems Shock Horizontal and vertical (ambient temperature) Half-sine, trapezoidal, sawtooth Electrodynamic vibrator Max severity 100 g Pulse width 2 to 27 ms (dependent upon g and item mass) Max item mass: 250 Kg Max item size: 1 x 1 x 2 BS EN :1993 IEC :1987 EF-STN 07-55:1975:Test 3 MIL-ST 202F:1980: Method 213B MIL-ST 810E:1989: Method Excluding methods h) Rail Impact g) Pyrotechnic Shock i) Catapult launch/arrested landing EF STN 00-35:1999 Test M3 Electrical, Electronic nd Mechanical Components: Vibration Insulation resistance Humidity High voltage Cold ry heat Salt mist Free fall Bump IP56 Ingress Protection LR Type pproval System Test Specification 1:2002 ETSI EN 300: V ( ) ETSI EN300: v ( ) Enclosures (ll Types) egree of protection against ingress by: dust solid objects water BS EN 60529:1992 IEC 529:1989 (withdrawn) Enclosures For Rotating Machinery Ingress by: dust solid objects water EN 60034:Part 5:1986 (withdrawn) IEC 60034:Part 5:1981 (withdrawn) Enclosures For Low Voltage Switch nd Control Gear Ingress by: dust solid objects water BS EN :1999 Clause ssessment Manager: WC1 Page 16 of 46

17 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ENVIRONMENTL TESTING (cont d) Electrical/Electronic Components Electrical/Electronic Equipments High Temperature Max temp: 70 C Chamber size: 3.0 m x 2.5 m x 2.2 m IEC :1974 Tests Ba, Bb EF STN 07-55:1975 Test B1 MIL-ST 202F:1980 Method 108 MIL-ST 810E:1989 Method EF STN 00-35:1999 Test CL1 Mechanical Components Max temp: 100 C Chamber size: 0.8 m x 0.6 m x 0.7 m Mechanical Equipments Max temp: 130 C Chamber size: 1.0 m x 1.0 m x 1.0 m Low Temperature Min temp: -30 C Chamber size: 3.0 m x 2.5 m x 2.2 m Min temp: -40 C Chamber size: 0.8 m x 0.6 m x 0.7 m BS EN 54-2:1997 Clause 15.4 BS EN 54-4:1997 Clause 9.5 BS EN :1993 IEC :1990 Tests a, b EF STN 07-55:1975 Test B4 MIL-ST 810E:1989 Method 502.3(1989) EF STN 00-35:1999 Test CL4 Min temp: -65 C Chamber size: 1.0 m x 1.0 m x 1.0 m ssessment Manager: WC1 Page 17 of 46

18 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ENVIRONMENTL TESTING (cont d) Electrical, Electronic nd Mechanical Components Change of temperature (gradual) Temp range: -40 C to 100 C Chamber size: 0.8 m x 0.6 m x 0.7 m Temp range: -25 C to 60 C Chamber size: 3.0 m x 2.5 m x 2.2 m BS 2011:Part 2-1:1985(1987) Test Nb BS EN :2000 IEC :1984 EF STN 00-35:1999 Test CL2, Procedure B EF STN 00-35:1999 Test CL5 Temp range: -65 C to 130 C Chamber size: 1.0 m x 1.0 m x 1.0 m High Humidity (constant & cyclic) Temp range: +10 C to +80 C Humidity range: 75% to 98% rh Max chamber size: 0.8 m x 0.6 m x 0.7m Temp range:+10 C to +60 C Humidity range: 20% to 98% rh Max chamber size: 3.0 m x 2.5 m x 2 m BS EN 54-2:1997 Clauses 15.5 and BS EN 54-4:1997 Clauses 9.6 and 9.14 BS 2011:Part 2.1:1977(1987) Test Ca BS 2011:Part 2.1:1990 Test Cb IEC :1969 IEC :1988 EF STN 07-55:1975 Test B7 BS 2011:Part 2.1:1981(1987) Test b IEC :1980 EF STN 07-55:1975 Test B6 MIL-ST 202F:1980 Method 106F(1990) MIL-ST 810E:1989 Method 507.3(1989) EF STN 00-35:1999 Test CL6 EF STN 00-35:1999 Test CL7 ssessment Manager: WC1 Page 18 of 46

19 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ENVIRONMENTL TESTING (cont d) Electrical, Electronic nd Mechanical Components High Humidity/Temperature Temp range: -40 C to 80 C Humidity range: 75% to 98% rh Chamber size: 0.8 m x 0.6 m x 0.7 m BS 2011:Part 2.1:1977 Test Z/ IEC :1974 Temp range: -25 C to +60 C Humidity range: 10% to 98% rh Max chamber size: 3.0 m x 2.5 m x 2.2 m Electrical, Electronic nd Mechanical Components Salt Mist Chamber size: 1.2 m x 0.8 m x 0.9 m BS 2011:Part 2.1:1982 Test Ka IEC :1981 EF STN 07-55:1975 Tests C5, C6 MIL-ST 202F:1980 Method 101 MIL-ST 810E:1989 Method Section II EF STN 00-35:1999 Test CN2 Free fall Mass limits 50 kg Height limit 1 m BS EN :1993 Test Ed IEC :1975 EF STN (Part 2):1975 Section 1.1 Test 9 EF STN 00-35:1999 Test M5 rop and Topple BS EN :1993 Test Ec IEC :1969 EF STN (Part 2):1975 Section 1/1 Test 4 EF STN 00-35:1999 Test M4 Impact (Spring hammer) 0.5 joules BS EN 54-2:1997 Clause 15.6 BS EN 54-4:1997 Clause 9.7 EN :1997 ssessment Manager: WC1 Page 19 of 46

20 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited LIGHTING & PHOTOMETRY Electrical Product Tests Luminaires Electrical safety BS EN :2015 excluding clauses 4.24 and 9.2 Fixed General Purpose Luminaires Electrical safety BS 4533:Part 102.1:1990 EN 60598:Part 2.1:1989 Recessed Luminaires Electrical Safety BS EN :1997 Luminaires For Road nd Street Lighting Electrical Safety BS EN : md 1 BS EN :1994 Portable General Purpose Luminaires Electrical Safety BS EN :1998 Floodlights Electrical Safety BS EN :1998 Luminaires With Built-In Transformers Portable Luminaires For Garden Use Electrical Safety BS EN :1995 Electrical Safety BS EN :1997 Handlamps Electrical Safety BS EN :1997 Photo nd Film Luminaires Electrical Safety BS 4533:Part 102.9:1990 EN 60598:Part 2.9:1989 Luminaires For Stage Lighting, Tv, Film nd Photographic Studios Electrical Safety BS 4533:Part :1990 EN 60598:Part 2-17:1989 Luminaires For Swimming Pools Electrical safety BS EN :1994 ir Handling Luminaires Electrical Safety BS 4533:Part :1990 EN :1989 In the above Lighting and Photometry Section, where IEC or EN standards have exact equivalents in BS or BS EN or EN Standards shown on the schedule, these are also included in the accreditation. ssessment Manager: WC1 Page 20 of 46

21 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited LIGHTING & PHOTOMETRY (cont d) Lighting Chains Electrical Safety BS EN : md 1 Luminaires For Emergency Lighting Electrical Safety BS EN :2014 excluding clauses 22.14, and Luminaires With Limited Surface Temperatures Electrical Safety BS EN :1999 Luminaires For Hospitals nd Health Care Buildings Track Systems For Luminaires Electrical Safety BS EN : md 1 EN :1994 IEC :1994 Electrical Safety BS EN 60570:2003 BS EN :1995 Ballasts: For Tubular Fluorescent Lamps Electrical Safety, Electrical, Mechanical and Tests BS EN 60921:2004 Excluding clause 13 IEC 60921:1988 Excluding clause 13 c-supplied Electronic Ballasts For Tubular Fluorescent Lamps Electrical Safety, Electrical, Mechanical and Tests BS EN 60925: md 1 & 2 Section 1 only (Clauses 3 to12) uxiliaries For Lamps Starting evices Electrical Safety, Electrical, Mechanical and Tests BS EN 60927: md 1 & 2 c-supplied Electronic Ballasts Fror Tubular Fluorescent Lamps BS EN 60928:1995 c Supplied Electronic Ballasts For Tubular Fluorescent Lamps Requirements Safety tests Maximum input voltage 250 V ac Rated Frequency 50 Hz only BS EN 60929:2004 excluding clauses 14 & 15 In the above Lighting and Photometry Section, where IEC or EN standards have exact equivalents in BS or BS EN or EN Standards shown on the schedule, these are also included in the accreditation. ssessment Manager: WC1 Page 21 of 46

22 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited LIGHTING & PHOTOMETRY (cont d) Ballasts For ischarge Lamps Other Than Tubular Fluorescent Lamps Electrical Safety, Electrical, Mechanical and BS EN 60923:2005 Lamp Control Gear General nd Safety Requirements Electrical Safety Tests Maximum input voltage 250 V ac Rated frequency 50 Hz only BS EN :2008 Excluding Clause 13 uxiliaries For Lamps Starting evices c Or c-supplied Electronic Stepdown Convertors For Filament Lamps c Supplied Electronic Ballasts For Fluorescent Lamps Electrical Safety BS EN :2001 Electrical Safety BS EN :2001 Electrical Safety BS EN :2001 Particular Requirements For c Supplied Electronic Ballasts For Emergency Lighting Electrical Safety, Electrical, Mechanical and Tests BS EN :2001 Excluding Clause 14 Ballasts: For Tubular Fluorescent Lamps Electrical Safety, Electrical, Mechanical and Tests BS EN :2001 Excluding Clause 15 Ballasts For ischarge Lamps Other Than Tubular Fluorescent Lamps Electrical Safety, Electrical, Mechanical and BS EN :2001 Excluding clauses 13 and 15.2 Miscellaneous Electronic Circuits Used With Luminaires c Or c Supplied Electronic Ballasts For ischarge Lamps Electrical Safety BS EN :2002 Electrical Safety BS EN :2005 In the above Lighting and Photometry Section, where IEC or EN standards have exact equivalents in BS or BS EN or EN Standards shown on the schedule, these are also included in the accreditation. ssessment Manager: WC1 Page 22 of 46

23 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited LIGHTING & PHOTOMETRY (cont d) c Or c Supplied Electronic Control Gear For Led Modules Electrical Safety BS EN :2006 c Or c-supplied Electronic Stepdown Convertors For Filament Lamps Electrical Mechanical Safety BS EN 61047:2004 Excluding Clause 11 Starters Electrical Safety, Electrical, Mechanical and Tests BS EN 60155:1995 EN Section 1:1989 (withdrawn) Self Ballasted Lamps For General Lighting Services Safety tests BS EN 60968:2000 Self Ballasted Lamps For General Lighting Electrical Safety, Electrical, Mechanical, and Photometric Tests BS EN 60969:1993 Connecting evices For Low-Voltage Circuits For Household nd Similar Purposes General requirements Electrical Mechanical Safety BS EN :2004 Connecting evices With Screw Type Clamping Units Electrical Safety, Particular requirements, Electrical and Mechanical Tests BS EN :2004 Connecting evices For Screwless Type Clamping Units Electrical Safety Particular requirements, Electrical and Mechanical Tests BS EN :2004 Photoelectric Control Units For Road Lighting Electrical Mechanical Photometric BS 5972:1980 In the above Lighting and Photometry Section, where IEC or EN standards have exact equivalents in BS or BS EN or EN Standards shown on the schedule, these are also included in the accreditation. ssessment Manager: WC1 Page 23 of 46

24 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ELECTRICL COMPONENTS Electrical Product Tests Solid nd Insulating Materials Under Moist Conditions Comparative and proof tracking indices BS EN 60112:2003 IEC 60112:2003 Plastic Materials Glow wire BS EN :2001 BS EN :2001 BS EN :2001 BS EN :2001 BS :1984 (withdrawn) Switches Electrical safety BS EN :1992 Cord Switches Electrical safety BS EN :1993 Changeover Selectors Electrical safety BS EN :1995 General Requirements For Electrical ccessories Not Covered By Other British Standards Electrical Safety BS 5733:1995 (Withdrawn) BS 5733:2010 Limitation: Clause 14.5, limited to 2.5 mm² CS maximum utomatic test systems for battery powered emergency escape lighting Electrical Safety BS EN 62034:2012, excluding clause EMC Testing Central power supply systems Electrical Safety BS EN 50171:2001 In the above Electrical Components Section, where IEC or EN standards have exact equivalents in BS or BS EN or EN Standards shown on the schedule, these are also included in the accreditation. ssessment Manager: WC1 Page 24 of 46

25 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ELECTRONIC EQUIPMENT & COMPONENTS Mains-Operated Electronic nd Related pparatus For Household nd Similar General Use: Electrical Product Tests Electrical Safety Electrical Product Tests Electrical Safety udio mplifiers udio Tape Recorders Battery Eliminators Electronic Organs Home Computers nd Similar ppliances Music Centres Radio Receivers Record Turntables Telecommunications Equipment Television Receivers Video Equipment Construction requirements ielectric strength Flammability Insulation after humidity Ionizing radiation (TV only) Isolation Mechanical strength and stability Overheating Safety labelling Shock and fire hazards with and without fault conditions BS EN 60065:2002 BS EN :1999 IEC 60065:2001 (withdrawn) Circuit Boards nd Enclosures For Tv Sets Fire resistance High Voltage Components (>4 Kv) Flammability Safety Isolation Components (Resistors, Capacitors, Switches, Transformers, etc) Construction requirements Insulation after damp heat Surge voltage breakdown In the above Electrical Components & Electrical Components Section, where IEC or EN standards have exact equivalents in BS or BS EN Standards shown on the schedule, these are also included in the accreditation. ssessment Manager: WC1 Page 25 of 46

26 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ELECTRONIC EQUIPMENT & COMPONENTS (cont d) Electronic Components nd Materials Used In IT Equipment IT Equipment Including Electrical Business Equipment ielectric strength and leakage current istance through insulation Heating during normal use Insulation after humidity Electronic isolation by creepage and clearance Ionising radiation Flammability Insulation resistance Measurement of telephone Network voltages (TNV) Mechanical strength and stability Safety labelling Shock and fire hazards with and without fault conditions BS EN :2006 BS EN :1999 IEC 60950:2005 Fixed Capacitors For Radio Interference Suppression (Limited To Capacitor Types Mounted By Their Connecting Leads) Capacitance Creepage and clearance amp heat Endurance Flammability Impulse voltage Insulation resistance Markings Resistance Soldering heat test Termination strength Voltage proof BS EN :1999 BS EN :1995 (Withdrawn) Table 3 only Electrical, Equipment For Measurement, Control nd Laboratory Use Electrical safety Voltage: up to 30 Kv dc up to 15 Kv rms BS EN :2010 EN :2010 IEC :2010 Excluding :- Clause 12.2, Ionizing radiation Clause 12.3, UV radiation Clause 12.4, Microwave radiation Clause Ultrasonic pressure Clause Laser sources UL :2002 Excluding :- Clause ssessment Manager: WC1 Page 26 of 46

27 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited ELECTRICL EQUIPMENT Uninterruptable Power Systems (UPS) Construction requirements ielectric strength and leakage current Flammability Heating during normal use Insulation after humidity Mechanical strength and stability Safety labelling Shock, energy, mechanical and fire hazards, with and without fault conditions BS EN :2003 (Withdrawn) BS EN :2003 (Withdrawn) Equipment To Be Connected To Telecommunication Networks Electrical Safety Network voltages (TNV) BS EN 41003:1999 S NZS :2003 No 60950:2000 (common standard) MEICL EQUIPMENT Medical Electrical Equipment Current imensional Electrical power Resistance/ impedance Humidity Mechanical Pressure Temperature Time Voltage BS 5724:Part 1:1989 md 1, 2, 3 EN :2006 IEC :1988 md 1 and 2 S/NZS :1998 UL :2003 ll excluding IEC referred to in Sub-clause 52.1, also Section 6 (Clause 37 to 41) and Clause 48 FENESTRTION oors - luminium Framed Sliding Glass imensional Functional/performance Load: bending Weather tightness BS 5286:1978 (withdrawn) Windows Operating forces BS :2009 excluding clauses 5.5 & 6.5 BS EN :2003 BS EN 13115:2001 ssessment Manager: WC1 Page 27 of 46

28 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited FENESTRTION (cont d) Static torsion BS :2009 BS EN 14609:2004 BS EN 13115:2001 Racking BS :2009 excluding clauses 5.5 & 6.5 BS EN 14608:2004 BS EN 13115:2001 Safety devices BS :2009 excluding clauses 5.5 & 6.5 BS EN 14609:2004 as amended by IHM C BS EN :2006 oors Operating forces BS :2009 excluding clauses 5.5 & 6.5 BS EN :2000 BS EN 12217:2003 Vertical load BS :2009 excluding clauses 5.5 & 6.5 BS EN 947:1999 BS EN 1192:2000 Static torsion BS :2009 excluding clauses 5.5 & 6.5 BS EN 948:1999 BS EN 1192:2000 Soft and heavy body impact BS :2009 excluding clauses 5.5 & 6.5 BS EN 949:1999 BS EN 1192:2000 Hard body impact BS :2009 excluding clauses 5.5 & 6.5 BS EN 950:1999 BS EN 1192:2000 Safety devices BS :2009 excluding clauses 5.5 & 6.5 BS EN 948:1999 as amended By IHM C BS EN :2006 ssessment Manager: WC1 Page 28 of 46

29 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited FENESTRTION (cont d) Specific luminium lloy Endurance Functional/performance requirements Load: bending BS 4873:2004 Steel Functional/performance requirements Load: bending BS 6510:2005 Upvc Plastics Functional/performance requirements Load: bending Mechanical BS 7412: 2007 Excluding nnex and B in respect to Clauses 6 and 7 Windows and oors Weathertightness BS :2015 ir permeability BS EN 1026:2000 Watertightness BS EN 1027:2000 Resistance to wind load BS EN 12211:2000 External oorsets - single and double leaf - single swing - hinged - inward and outward opening - with or without integral side panels and fanlights - pivot doors - stable Security hardware and cylinder test (Parts 1 & 2) Manipulation test Infill manual test Infill mechanical test Manual cutting test Mechanical loading test Manual check test Soft body impact test Hard body impact test PS 24:2016 PS 24:2012 Letter Plates Security of fixings BS EN 13724:2002 as amended by PS 24:2012 ssessment Manager: WC1 Page 29 of 46

30 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited FENESTRTION (cont d) Windows: Singular and Multilight - top hung (open out), side hung (open in and open out, bottom hung (open in), butt hinged - top and side hung (open out) projected - top hung fully reversible - side hung fully reversible - tilt and turn and turn and tilt - fixed and dummy vents - double opening (French windows) - horizontal sliding Manipulation test Infill manual test Infill mechanical test Mechanical loading test Manual check test PS 24:2016 PS 24:2012 ssessment Manager: WC1 Page 30 of 46

31 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited GLSS, SHEET and BUILING PROUCTS Glass nd Glazing General: imensional Specific: Glass In Buildings Impact test BS EN 12600:2002 Fragmentation BS EN :2000 Clause 8 BS EN :2000 Clause 8 4-point bend BS EN :2000 Glass In Buildings (cont d) etermination of surface stress STM C Insulating Glass Units (ouble Glazed) Moisture penetration index ew point temperature Inorganic desiccant moisture content (950 C drying method) BS EN :2002 Organic desiccant moisture content (Karl Fischer method) ocumented In-House Method T based on BS EN :2002 Gas leakage rate Filling gas concentration (rgon filling only) BS EN :2002 Fogging test BS EN :2002, nnex C Safety Glass & Plastics For Road Vehicles Mechanical Optical Physical BS 857:1967(1990) ECE Regulations 43 EEC Tractor irective 89/173/EEC NSI Z.26.1 (US) ccess Equipment Portable luminium Ladders, Steps, Trestles nd Lightweight Staging Constructional requirements tests BS 2037:1994 ssessment Manager: WC1 Page 31 of 46

32 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited GLSS, SHEET and BUILING PROUCTS (cont d) Specific (cont d) Ladders Constructional requirements esign requirements tests BS 1129:1990 BS EN 131-2:1993 BS EN 131-2:2010 (excluding Clause 5.16) PLUMBING & COPPER CYLINERS Cylinders For omestic Water General: Capacity Construction requirements imensional Pressure SPECIFIC: Copper Cylinders Thermal efficiency BS :2002 Float Operated Valves iaphragm Type (Plastic Body) BS :1990 Insulating Jackets For omestic Hot Water Storage Cylinders Construction requirements imensional Mass Thermal efficiency BS 5615:1985 Malleable Cast Iron nd Cast Copper lloy Threaded Pipes nd Fittings Construction requirements imensional (excluding thread gauging) Finish: coating Mass Pressure BS 143:1993 BS 1256:2000 Excluding Clauses 8.1, 8.2, 8.3 and 8.4 BS EN 10242:1995 Tensile test (up to 100kN) ssessment Manager: WC1 Page 32 of 46

33 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited PLUMBING & COPPER CYLINERS (cont d) Tubes nd Fittings General: imensional Mechanical properties Pressure Carbon film tests Copper Tubes For Water, Gas nd Sanitation BS EN 1057:2006 excluding Clauses 8.3, 8.4 and 8.6 Capillary nd Compression Tube Fittings Of Copper nd Copper lloy For Copper Tubes BS 864:Part 2:1983 BS EN :1998 excluding Clauses 4.2, 5.5 and 5.6 BS EN :1998 excluding Clauses 5.8 and 5.9 BS EN :1998 Capillary nd Compression Tube Fittings Of Copper nd Copper lloy For Polyethylene Pipes BS 864:Part 5:1990 raining Taps (Screw-own Pattern) BS 2879:1980(1988) Valves nd Unions For Hot Water Radiators BS 2767:1991 THERML INSULTION FOR USE IN PITCHE ROOF SPCES IN WELLINGS: Man-Made Mineral Fibre In Pelleted Or Granular Form For pplication By Blowing imensional Flammability Mass BS 5803:Part 2:1985 (Obsolescent) excluding Clauses 4.1, 4.5 and 5 ssessment Manager: WC1 Page 33 of 46

34 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited THERML INSULTION FOR BUILINGS: Factory Made Mineral Wool (MW) Products BS EN 13162:2008 Clauses 11, 12, 13 & 15 SITE CTIVITIES Portable Fire Extinguishers Class and Class B BS EN 3-7: :2007 Clause 15 C BS 6165:2002 Clause 7.6 BS EN :2007 Clause 8 HOUSEHOL OR SIMILR GS PPLINCES esign and Construction Safety of Operation Thermal Efficiency Excluding non-metallic materials tested to BS EN 549, BS EN 278, BS EN 279, BS 3212, ISO 1817 and excluding lint tests Testing to the following specifications to demonstrate compliance with the European Gas ppliance irective 2009/142/EC or compliance with the specification Cooking ppliances including Independent Hotplates, Barbecues and Ovens BS EN :2008 BS EN :2012 BS EN :2012 BS EN :1998 BS EN :2002 BS EN :1999 BS EN 498:2012 BS EN 484:1998 S 4551:2008 S 4557:2004 NSI Z21.1:2005 ssessment Manager: WC1 Page 34 of 46

35 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited HOUSEHOL OR SIMILR GS PPLINCES (cont d) Specification for dedicated liquefied petroleum gas appliances. Multi-purpose boiling burners for outdoor use BS EN 497:1998 Natural Gas Barbecues for Outdoor Use TP 6.9 (Internal Certification Procedure) Heat Storage Cookers TP 6.10 (Internal Certification Procedure) Flueless Heat Storage Cookers TP 6.15 (Internal Certification Procedure) Gas Ovens For Household Use (Energy labelling tests) BS EN 15181:2008 Central Heating Boilers nd Circulators BS EN 297:1994 BS EN 483:1999 BS EN 625:1996 BS EN 677:1998 S 4560:2004 Fuel Cell Heating ppliances BS EN 50465:2008 BS EN 50465:2015 Combined Fire/Back Boiler Or Circulator Gas-fired heating boilers. General requirements and tests Gas-fired central heating boilers. Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding kw BS :2003 BS EN :2012 BS EN :2012 Excluding Clause , corrosion test ssessment Manager: WC1 Page 35 of 46

36 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited WTER HETERS BS EN 26:1998 (inc. 1, 2 and 3) BS EN 89:2000 BS EN 15033:2006 (excluding Clause 6.2 (vibration test)) S 4552:2005 Instantaneous Water Heaters > 45 kw TP 6.3 (Internal Certification Procedure) Instantaneous Condensing Water Heaters TP 6.4 (Internal Certification Procedure) Instantaneous Condensing Water Heaters for Outdoor Use TP 6.5 (Internal Certification Procedure) Gas Fires nd Space Heaters BS EN 509:2000 BS EN 613:2001 BS EN 1266:2002 BS :2009 BS EN 13278:2013 S 4553:2008 Space Heaters (EN 613) ppliances With C31 Flues TP 6.13 (Internal Certification Procedure) Space Heaters (EN 613) ppliances For Unattended Operation TP 6.14 (Internal Certification Procedure) Flueless Heaters BS EN 14829:2007 Flueless LPG Space Heaters Excluding catalytic heaters BS EN 449:2002 ir Heaters BS EN 778:2009 BS EN 1196:2011 BS EN 1319:2009 BS 5258:Part 9:1989 BS 6332:Part 6:1990 Lpg bsorption Refrigerators BS EN 732:1999 S 4555:2002 Portable Vapour Pressure Lpg ppliances BS EN 521:2006 S 2658:2008 ssessment Manager: WC1 Page 36 of 46

37 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited WTER HETERS (cont d) Portable Gas Cookers Using Non-Refillable Gas Canisters TP 6.20 (Internal Certification Procedure) Tumble ryers BS EN :2011 Flueless Patio Heaters BS EN 14543:2005 ecorative Open Flame ppliances For Outdoor Use TP 6.24 (Internal Certification Procedure) Room Sealed Lpg Space Heaters For Vehicles nd Boats (excluding appliances intended for use while vehicle or boat is in motion) BS EN 624:2011 (excluding Clauses (vibration test) and 6.25 (for vehicles in motion)) COMMERCIL GS HETE CTERING EQUIPMENT esign and Construction Safety of Operation Thermal Efficiency Excluding non-metallic materials tested to BS EN 549, BS EN 278, BS EN 279, BS 3212, ISO 1817 BS EN 203-1:2014 BS EN :2005 BS EN :2006 BS EN :2005 BS EN :2005 BS EN :2005 BS EN :2014 BS EN :2005 BS EN :2005 BS EN :2007 BS EN :2006 S 4563:2004 Professional Catering Barbecues TP 6.19 (Internal Certification Procedure) Hog/Pig Roasters TP 6.21 (Internal Certification Procedure) Overhead Radiant Heaters BS EN 416-1:2009 BS EN 416-2:2006 BS EN 419-1:2009 BS EN 419-2:2006 S 4643:2007 Gas Radiant Heaters For Outdoor Use TP 6.22 (Internal Certification Procedure) ssessment Manager: WC1 Page 37 of 46

38 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited COMMERCIL GS HETE CTERING EQUIPMENT (cont d) Lpg Space Heaters BS EN 461:1999 BS EN 1596:1998 Heating Boilers - Forced raught BS EN 303-1:1999 Boiler Body nd Forced raught Burners Excluding appliances >800 kw BS EN 303-3:1999 Hot Water Boilers Excluding appliances >800 kw BS EN 656:2000 BS 5978:Part 1:1989 BS 5978:Part 2:1989 BS 5978:Part 3:1989 BS EN 13836:2006 BS EN 15417:2006 BS EN 15420:2010 ir Heaters BS 5990:2006 BS 5991:2006 BS EN 525:2009 BS EN 1020:2009 BS EN 12669:2000 BS EN 621:2009 Tumble ryers BS EN :1999 S 4554:2005 Commercial ryers > 20 Kw TP 6.8 (Internal Certification Procedure) GS CRRYING CONTROLS esign and Construction Safety of Operation Excluding non-metallic materials tested to BS EN 549, BS EN 278, BS EN 279, BS 3212, ISO 1817 ssessment Manager: WC1 Page 38 of 46

39 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited GS CRRYING CONTROLS (cont d) Electrical components tested to BS EN :2001 but excluding IP Tests to IEC 529 and materials to BS 7461:1991 Manually Operated Ball Valves BS EN 331:1998 Ball Valve Families 2-4 TP 6.7 (Internal Certification Procedure) Taper Plug Valves BS 1552:1995 utomatic Shut-Off Valves BS EN 161:2011 (excluding Clauses 8.5 to 8.10 (EMC)) S 4629:2005 Excluding Clause 8, EMC tests of BS EN to 8.10 EMC Pressure Governors Excluding control dimensions > N 50 BS EN 88-1:2011 S 4618 : 2004 istribution Valves GIS/V7 Part 3:2014 Multifunction Gas Controls BS EN 126:2012 Excluding Clause 8, EMC tests of BS EN to 8.10 EMC TP 6.26 (Internal Certification Procedure - MFCs with Single ctuator on cting on Two Closure Members) Flame Supervision evices BS EN 125:2010 BS 6047:Part 1:1981 Gas Taps BS EN 1106:2010 S 4617:2004 TP 6.27 (Internal Certification Procedure - Laboratory Gas Taps) ssessment Manager: WC1 Page 39 of 46

40 Schedule of ccreditation United Kingdom ccreditation Service ccredited to BSI ssurance UK Limited GS CRRYING CONTROLS (cont d) Safety nd Control evices BS EN 13611:2007 (excluding Clauses (vibration), and 8.8 to 8.10 (EMC)) Normally Open (Vent) Valves TP 6.16 (Internal Certification Procedure) Pressure regulators, automatic change-over devices, having a maximum regulated pressure of 4 bar, with a maximum capacity of 150 kg/h, associated safety devices and adaptors for butane, propane, and their mixtures Limited to maximum flowrate of 14 Kg/h BS EN 16129:2013 Thermostats BS EN 257:2010 Gas/ir Ratio Controls Excluding control dimensions > N 50 BS EN :1999 NCILLIRIES RELTING TO GS EQUIPMENT esign and Construction Excluding non-metallic materials tested to BS EN 549, BS EN 278, BS EN 279, BS 3212, ISO 1817 Flue Pipes nd ccessories Flue Terminals only BS EN :2009 Flexible Hoses & Connection Valves BS 669:Part 1:1989 BS 669:Part 2:1997 BS EN 15069:2008 BS EN 14800: 2007 (excluding Clause 11 (reaction to fire)) BS EN 15266:2007 (excluding Clause 5.16 (reaction to fire)) iaphragm Gas Meters Construction and Marking only BS EN 1359:1999 (Clauses 6 & 8) ssessment Manager: WC1 Page 40 of 46