- PDF Free Download

Size: px

Start display at page:

Download "https://support.industry.siemens.com/cs/ww/en/view/"

Gyles Heath
6 years ago
Views:

Reading out the S7-1500 CPU Alarm using "" and

OPC UA Client https://support.industry.siemens.

1 Reading out the S CPU Alarm using "" and sending it to an Alarm System TIA Portal, S7-1500, OPC UA Client Siemens Industry Online Support

2 Siemens AG 2017 All rights reserved Warranty and Liability Warranty and Liability Note The Application Examples are not binding and do not claim to be complete regarding the circuits shown, equipping and any eventuality. The Application Examples do not represent customer-specific solutions. They are only intended to provide support for typical applications. You are responsible for ensuring that the described products are used correctly. These Application Examples do not relieve you of the responsibility to use safe practices in application, installation, operation and maintenance. When using these Application Examples, you recognize that we cannot be made liable for any damage/claims beyond the liability clause described. We reserve the right to make changes to these Application Examples at any time without prior notice. If there are any deviations between the recommendations provided in these Application Examples and other Siemens publications e.g. Catalogs the contents of the other documents have priority. We do not accept any liability for the information contained in this document. Any claims against us based on whatever legal reason resulting from the use of the examples, information, programs, engineering and performance data etc., described in this Application Example shall be excluded. Such an exclusion shall not apply in the case of mandatory liability, e.g. under the German Product Liability Act ( Produkthaftungsgesetz ), in case of intent, gross negligence, or injury of life, body or health, guarantee for the quality of a product, fraudulent concealment of a deficiency or breach of a condition which goes to the root of the contract ( wesentliche Vertragspflichten ). The damages for a breach of a substantial contractual obligation are, however, limited to the foreseeable damage, typical for the type of contract, except in the event of intent or gross negligence or injury to life, body or health. The above provisions do not imply a change of the burden of proof to your detriment. Any form of duplication or distribution of these Application Examples or excerpts hereof is prohibited without the expressed consent of the Siemens AG. Security information Siemens provides products and solutions with industrial security functions that support the secure operation of plants, systems, machines and networks. In order to protect plants, systems, machines and networks against cyber threats, it is necessary to implement and continuously maintain a holistic, state-of-the-art industrial security concept. Siemens products and solutions only form one element of such a concept. Customer is responsible to prevent unauthorized access to its plants, systems, machines and networks. Systems, machines and components should only be connected to the enterprise network or the internet if and to the extent necessary and with appropriate security measures (e.g. use of firewalls and network segmentation) in place. Additionally, Siemens guidance on appropriate security measures should be taken into account. For more information about industrial security, please visit Siemens products and solutions undergo continuous development to make them more secure. Siemens strongly recommends to apply product updates as soon as available and to always use the latest product versions. Use of product versions that are no longer supported, and failure to apply latest updates may increase customer s exposure to cyber threats. To stay informed about product updates, subscribe to the Siemens Industrial Security RSS Feed under Entry ID: , V1.0, 09/2017 2

3 Siemens AG 2017 All rights reserved Table of Contents Table of Contents Warranty and Liability Introduction Overview Mode of operation Prerequisites " basics Engineering Hardware configuration Components used Programming of TIA Portal project Configuring the OPC UA server of the S Receiving pending alarms in PLC_1 using "" and sending it to PLC_ Reading out of the received alarms Reading out of the received alarms in TIA Portal Reading out of the received alarms via web server Reading out of the received alarms via the OPC UA Client Acknowledgement of the received alarm Acknowledgement of the received alarm in TIA Portal Acknowledgement of received alarm using the OPC UA client Annex Service and support Links and literature Change documentation Entry ID: , V1.0, 09/2017 3

4 Siemens AG 2017 All rights reserved 1 Introduction 1 Introduction 1.1 Overview Since the publication of TIA Portal V14 you can directly read out alarms from the alarm server of the S PLC using the "" instruction. These alarms can be sent to higher-level alarm system (e.g. PC, PLC). 1.2 Mode of operation The incoming and outgoing alarms of the S PLC_1 are read out and acquired and saved in a "alarmstorage" data block in PLC_1. Afterwards you can send these alarms from PLC_1 with the "TSEND_C" instruction as string to PLC_2. The alarms are received on the PLC_2 with the "TRCV_C" instruction and stored in a "rcvdstorage" data block. The alarms received via "" can be read out via OPC UA Client. Figure 1-1 S (PLC_1) S (PLC_2) TSEND_C TRCV_C currrecord alarmstorage #sendstruct (alarmdata) (0 x) #trcvstruct rcvdstorage (0 x) (SGetAlarm) (rcvgetalarm) Request Response Request Response OPC Server OPC Server OPC Client You can use the " instruction for the following PLC alarms of the S7-1500: Program_Alarm System diagnostics Standard Motion Control Security (e.g. wrong login) SINUMERIK GRAPH ProDiag Entry ID: , V1.0, 09/2017 4

Siemens AG 2017 All rights reserved 1 Introduction 1.3 Prerequisites The following requirements must be met when using the "" instruction: TIA Portal V14 S7-1500 PLC as of firmware V2.

5 Siemens AG 2017 All rights reserved 1 Introduction 1.3 Prerequisites The following requirements must be met when using the "" instruction: TIA Portal V14 S PLC as of firmware V2.0 The following setting is recommended for the use of "": Enable the "Central alarm management in the PLC" property in the hardware configuration of the S PLC. This property is enabled by default for new projects. Figure 1-2 Note If you do not enable the PLC property "Central alarm management in the PLC" in the hardware configuration, only the IDs of the alarm text fields will be output instead of the alarm texts. 1.4 " basics The basics on the "" instruction can be found in the same application example in the documentation: _Grundlagen DOC_V10_en.pdf. This file can be found on the entry page of the application example Entry ID: , V1.0, 09/2017 5

6 Siemens AG 2017 All rights reserved 2 Engineering 2 Engineering 2.1 Hardware configuration The following figure shows the hardware with which it was tested. Figure 2-1 STEP 7 S PLC_1 S PLC_2 PROFINET IE Alarm Alarm Alarm ET 200MP PN ET 200SP PN 2.2 Components used This application example was created with the following hardware and software components: Table 2-1 Component Numbe r Article number Note CPU PN/DP 1 6ES AN01-0AB0 PLC_1 with firmware V2.1 CPU PN 1 6ES AL01-0AB0 PLC_2 IM PN ST 1 6ES7155-5AA00-0AB0 ET 200MP DI 32x24VDC HF 1 6ES BL00-0AB0 - DQ 32x24VDC/0.5A ST 1 6ES BL00-0AB0 - AI 8xU/I/RTD/TC ST 1 6ES KF00-0AB0 - IM PN ST 1 6ES AU00-0BN0 ET 200SP DI 8x24VDC ST 1 6ES BF00-0BA0 - DQ 8x24VDC/0.5A ST 1 6ES BF00-0BA0 - AQ 4xU/I ST 1 6ES HD00-0BA1 - Server module 1 6ES PA00-0AA0 - STEP 7 Professional V14 SP1 1 6ES OPC UA Expert 1 Version Free Download Entry ID: , V1.0, 09/2017 6

7 Siemens AG 2017 All rights reserved 2 Engineering This application example consists of the following components: Table 2-2 Component Basic documentation Project documentation STEP 7 project File name _Grundlagen DOC_V10_de.pdf DOC_V10_de.pdf PROJ_V10.zip 2.3 Programming of TIA Portal project The enclosed STEP 7 project does not require any further configuration and can be operated. Note This STEP 7 project was created on the basis of the program example for & Ack_Alarms" example in the online help of "STEP 7 Professional V14 SP1". The acknowledgement of the alarm and reading out of alarms received using via the UaExpert OPC UA client in this application example, are not included in the online help. The configuration of the OPC UA server can be found in chapter 2.4. If you do not use the included STEP 7 project but create your own project, carry out the required configuration steps from the chapter Program example for & Ack_Alarms" Configuring the OPC UA server of the S The OPC UA server of the S is disabled by default. If you do not use the STEP 7 project included but want to create your own project, you have to plan and configure the OPC UA Server. The configuration steps required can be found in the documentation in chapter 2.1 "Configuring the OPC UA Servers of the S7-1500" in the "OPC UA.NET Client for the SIMATIC S OPC UA Server" application example. Entry ID: , V1.0, 09/2017 7

8 Siemens AG 2017 All rights reserved This chapter shows you how to commission and operate the application example. Load the prepared STEP 7 project into your controller. Proceed as follows: 1. Download the " PROJ_V10.zip" file onto your hard drive. The download can be found on the entry page of the application example 2. Extract the zipped download file. 3. Navigate to "" in the unzipped folder. The STEP 7 project is located in this folder. 4. Open the STEP 7 project by double-clicking on the ".ap14" file. 5. Select the PLC_1 or PLC_2 folder in the project tree and click the Download to device button in the toolbar. The STEP 7 project contains the following UseCases: Receiving pending alarms in PLC_1 using "" and sending it to PLC_2. Reading out of the received alarms Acknowledgement of the received alarm Entry ID: , V1.0, 09/2017 8

Siemens AG 2017 All rights reserved 3.1 Receiving pending alarms in PLC_1 using "" and sending it to PLC_2. In order to receive pending alarms in PLC_1 and to send it to PLC_2, proceed as follows: 1.

2. Establish connection: You have to establish the connection between PLC_1 and PLC_2 in the following sequence: a. Set the tags TRCV_C.start and TRCV_C.

9 Siemens AG 2017 All rights reserved 3.1 Receiving pending alarms in PLC_1 using "" and sending it to PLC_2. In order to receive pending alarms in PLC_1 and to send it to PLC_2, proceed as follows: 1. Connect online: a. Select the PLC_1 folder in the project tree and click the Go online button in the toolbar. b. Select the PLC_2 folder in the project tree and click the Go online button in the toolbar. 2. Establish connection: You have to establish the connection between PLC_1 and PLC_2 in the following sequence: a. Set the tags TRCV_C.start and TRCV_C.comControl" to "TRUE in the SLI_gDB_trcv_GAA DB of the PLC_2. Figure 3-1 b. Set the TSEND_C.comControl tag to "TRUE in the SLI_gDB_GAlarm DB of PLC_1. Figure Generate alarms: Create one or several alarms as follows: a. Drag a module to the ET200SP b. Cause a wire break at the ET200MP input channel. c. Generate a ProgDiag alarm in the SLI_gDB_testAlarm_GAA DB of the PLC_1 by setting the monitor tags startpump and closevalue to TRUE. Entry ID: , V1.0, 09/2017 9

Siemens AG 2017 All rights reserved Figure 3-3 4.

10 Siemens AG 2017 All rights reserved Figure Start "": Set the "GetAlarm.start" tag to "TRUE" in the "SLI_gDB_GAlarm" DB of the PLC_1. Figure 3-4 Note The "GetAlarm.start" tag is automatically reset after its processing in the user program. Entry ID: , V1.0, 09/

New alarms are received with the "AlarmData" data type, saved in the "alarmstorage" storage array and sent to PLC_2 via the "TSEND_C" instruction.

11 Siemens AG 2017 All rights reserved Once you have started the "" instruction, the following steps are carried out in the background: a. The "" instruction is called in "OperateMode = 1" and then goes to "OperateMode = 2". b. New alarms are received with the "AlarmData" data type, saved in the "alarmstorage" storage array and sent to PLC_2 via the "TSEND_C" instruction. Figure 3-5 Note The storage array for the alarmstorage alarms can store a maximum of 16 alarms in this project. If you want to change the storage size you have to adjust the respective array size and the maximum value "maxposition". c. The new alarm is received using the "TRCV_C" instruction in PLC_2 and saved in "SLI_gDB_trcv_GAA" DB in the "rcvdstorage" storage array. Figure 3-6 After the transfer of the data record (#trcvstruct) to PLC_2, the communication connection is continuously monitored and the "TRCV_C" instruction is ready to receive new alarms. Entry ID: , V1.0, 09/

Select the PLC_1 folder in the project tree and click the Go online button in the toolbar. 2. Open the alarmstorage storage array in the SLI_gDB_GAalarm DB in which the alarms are copied.

12 Siemens AG 2017 All rights reserved 3.2 Reading out of the received alarms You have three options to read out received alarms via "": In the TIA Portal Using the PLC web server Using OPC UA client via "UaExpert" Reading out of the received alarms in TIA Portal In order to read out the received alarms in PLC_1 in the TIA Portal, proceed as follows: 1. Select the PLC_1 folder in the project tree and click the Go online button in the toolbar. 2. Open the alarmstorage storage array in the SLI_gDB_GAalarm DB in which the alarms are copied. The alarms can be seen in the respective array [Array 0 15] in alarm > AlarmText. Figure 3-7 In order to read out the received alarms in PLC_2 in the TIA Portal, proceed as follows: 1. Select the PLC_2 folder in the project tree and click the Go online button in the toolbar. 2. Open the GetAlarm watch table and click on the Monitor all button. Figure Or open the rcvdstorage storage array in SLI_gDB_trcv_GAA DB in which the alarms are copied. You can see the alarms in the respective array [Array 0 15] in AlarmText. Entry ID: , V1.0, 09/

2 Reading out of the received alarms via web server In order to read out the received alarms via the web server in PLC_1, proceed as

13 Siemens AG 2017 All rights reserved Figure Reading out of the received alarms via web server In order to read out the received alarms via the web server in PLC_1, proceed as follows: 1. Call the IP address of the PLC_1 (in the example: ) in a browser of your choice. 2. Open the "Alarms" in the project tree. Figure 3-10 In order to read out the received alarms via the web server in PLC_2, proceed as follows: 1. Call the IP address of the PLC_2 (in the example: ) in a browser of your choice. 2. Open the "GetAlarm" watch tables in the project tree. Figure 3-11 Note For the watch table to be displayed in the web server, you have to enable it first in the hardware configuration of the S PLC "Web server > User management" property. Entry ID: , V1.0, 09/

3.2.3 Reading out of the received alarms via the OPC UA Client In order to the OPC "UaExpert" UA Client, the following is assumed: "UaExpert" is installed on your

14 Siemens AG 2017 All rights reserved Figure Reading out of the received alarms via the OPC UA Client In order to the OPC "UaExpert" UA Client, the following is assumed: "UaExpert" is installed on your PC. UaExpert Download OPC UA server is enabled in PLC_1 and PLC_2. The STEP 7 project is loaded in the controller. In order to read out the received alarms in PLC_1 via the OPC "UaExpert" UA Client, proceed as follows: 1. Start "UaExpert" by double clicking it Click on the "Add Server" button. In the dialog, double-click on "< Double click to Add Server >" in the "Custom Discovery list area. Entry ID: , V1.0, 09/

Siemens AG 2017 All rights reserved 3. In the dialog that follows, enter the URL of the OPC UA server of the PLC_1 (in the example: opc.tcp://192.168.0.1) and click "OK". 4.

15 Siemens AG 2017 All rights reserved 3. In the dialog that follows, enter the URL of the OPC UA server of the PLC_1 (in the example: opc.tcp:// ) and click "OK". 4. Select a detected endpoint of the OPC UA server to which you want to establish a connection. (e.g.: SIMATIC.S OPC-UAServer:PLC1 None -None) Since no user is stored in this application example, the Anonymous field in Authentication Settings is enabled. 5. Set the "Connect Automatically" check box and confirm it using OK. 6. Accept the server certificate in the dialog that follows, by setting the "Accept the server certificate temporarily for this session" check box and then clicking "Continue". You are connected with the OPC UA server of the PLC_1. 7. Navigate to "Root > Objects > PLC_1 > DataBlocksGlobal > SLI_gDB_GAalarm > GetAlarm > alarmstorage > [0..15] in the "Address Space" of the server and drag the Alarmtext tag in the "Data Access View" area using drag-and-drop. 8. You can monitor the alarms in the "Data Access View" area in the Value column. Figure 3-13 If you read out the received alarms in PLC_2, perform the steps just as for PLC_1 but for PLC_2. Enter the URL of the OPC UA servers of the PLC_2 (opc.tcp:// ). Navigate to "Root > Objects > PLC_2 > DataBlocksGlobal > SLI_gDB_trcv_GAA > GetAlarm > rcvdstorage > [0..15] in the "Address Space" of the server and drag the Alarmtext tag in the "Data Access View" area using drag-and-drop. Entry ID: , V1.0, 09/

Siemens AG 2017 All rights reserved Figure 3-14 3.

PLC_1 receives the acknowledgement bit via TRCV_C. 3.

16 Siemens AG 2017 All rights reserved Figure Acknowledgement of the received alarm You can acknowledge the received alarm in PLC_2 and send the acknowledgment bit using the TSEND_C instruction to PLC_1. PLC_1 receives the acknowledgement bit via TRCV_C Acknowledgement of the received alarm in TIA Portal In order to acknowledge the received alarm in TIA Portal in PLC_2 and to send the acknowledgment bit to PLC_1, proceed as follows: 1. Establish connection: You have to establish the connection between PLC_1 and PLC_2 in the following sequence: a. Set the start and comcontrol" tags to "TRUE in the SLI_gDB_TRCV_C_AckBit DB of PLC_1. Figure 3-15 b. Set the "comcontrol" tag in the SLI_gDB_TSEND_C_AckBit DB of the PLC_2 to "TRUE. Entry ID: , V1.0, 09/

Siemens AG 2017 All rights reserved Figure 3-16 2. Acknowledge alarm: Set the "executeack" tag in the SLI_gDB_TSEND_C_AckBit DB of the PLC_2 to "TRUE.

Select the PLC_1 folder in the project tree and click the Receive alarms button in the toolbar in order to see the acknowledged alarms in PLC_1.

17 Siemens AG 2017 All rights reserved Figure Acknowledge alarm: Set the "executeack" tag in the SLI_gDB_TSEND_C_AckBit DB of the PLC_2 to "TRUE. The acknowledgement bit is set in PLC_2. Figure The acknowledgment bit is sent to PLC_1, the alarm is acknowledged and the alarm is displayed as acknowledged. Select the PLC_1 folder in the project tree and click the Receive alarms button in the toolbar in order to see the acknowledged alarms in PLC_1. The alarms are listed in the Diagnostics, Alarm display" tab. Figure Eliminate the fault. The alarm is deleted in the alarm display. 5. Reset the acknowledgement bit in PLC_2, by changing the "executeack" tag to "FALSE". Entry ID: , V1.0, 09/

18 Siemens AG 2017 All rights reserved Acknowledgement of received alarm using the OPC UA client In order to acknowledge the received alarm via the OPC "UaExpert" UA Client and to send acknowledgment bit to PLC_1, proceed as follows: 1. Connect the PLC_1 and PLC_2 as follows Establish connection 2. Perform the steps in Read out alarm using OPC UA client up to step [7], but for PLC_2. 3. Navigate to "Root > Objects > PLC_2 > DataBlocksGlobal > SLI_gDB_TSEND_C_AckBit > AckAlarm in the "Address Space" of the server 4. Drag the executeack tag in the "Data Access View" area using drag-anddrop. 5. Set the executeack tag in the Value column by double-clicking TRUE. The acknowledgement bit is set in PLC_2. 6. The acknowledgment bit is sent to PLC_1, the alarm is acknowledged and the alarm is displayed as acknowledged. Select the PLC_1 folder in the project tree and click the Receive alarms button in the toolbar in order to see the acknowledged alarms in PLC_1. The alarms are listed in the "Diagnostics > Alarm display" tab. Figure Eliminate the fault. The alarm is deleted in the alarm display. 8. Reset the acknowledgement bit in PLC_2, by changing the "executeack" tag to "FALSE". Entry ID: , V1.0, 09/

19 Siemens AG 2017 All rights reserved 4 Annex 4 Annex 4.1 Service and support Industry Online Support Technical Support Do you have any questions or need support? Siemens Industry Online Support offers access to our entire service and support know-how as well as to our services. Siemens Industry Online Support is the central address for information on our products, solutions and services. Product information, manuals, downloads, FAQs and application examples all information is accessible with just a few mouse clicks at Siemens Industry's Technical Support offers quick and competent support regarding all technical queries with numerous tailor-made offers from basic support right up to individual support contracts. Please address your requests to the Technical Support via the web form: Service offer Our service offer comprises, among other things, the following services: Product Training Plant Data Services Spare Parts Services Repair Services On Site and Maintenance Services Retrofit and Modernization Services Service Programs and Agreements Detailed information on our service offer is available in the Service Catalog: Industry Online Support app Thanks to the "Siemens Industry Online Support" app, you will get optimum support even when you are on the move. The app is available for Apple ios, Android and Windows Phone: Entry ID: , V1.0, 09/

20 Siemens AG 2017 All rights reserved 4 Annex 4.2 Links and literature Table 4-1 No. \1\ Siemens Industry Online Support Topic \2\ Link to the entry page of the application example \3\ STEP 7 Professional V14 SP1 System Manual \4\ Homepage of OPC UA Expert Change documentation Table 4-2 Version Date Modification V1.0 09/2017 First version Entry ID: , V1.0, 09/

BRAUMAT Function description Tank Cooling Management

Function Manual 01/2014 BRAUMAT Function description Tank Cooling Management BRAUMAT with STEP 7 https://support.industry.siemens.com/cs/ww/en/view/80142364 Siemens AG 2014 All rights reserved Warranty