D3-1 Two-way Digital Keypad Alarm System User Manual

Size: px

Start display at page:

Download "D3-1 Two-way Digital Keypad Alarm System User Manual"

Earl Lang
5 years ago
Views:

1 D3-1 Two-way Digital Keypad Alarm System User Manual

2 Foreword I. Introduction Thanks for purchasing BIBENE D3-1 alarm system. Please read this user manual carefully before use, we will update this manual on a regular basis in accordance with the addition or upgrade of the product features. If you need any assistance, please contact our support team, we will contact you within 24 hours. Customer Service Address: lhxing@hotmail.com Warm Tip: Customers who have purchased before: Can start and focus on chapter 5(Quick Start by Easy Testing) & chapter 6 ( Zone Features Introduction) Freshman: Please follow the step start from chapter 1

3 Table of Contents 1.Product Features Operating Principle Check Kit Accessory Button Introduction Main panel Button ARM: DISARM: Away Home Mode At Home Mode: Chime/alarm Switch Remote Control Button PIR Motion Sensor Button Door/window Sensor Quick Start by Easy Testing Check Zone for Door/Window Sensor Zone Features Introduction Features of 4 Modes Zones List of zone feature setting: Zone Features Setting Expand more accessory Add Remote Control Delete Remote Control Add Door/window Sensors Delete Door/window Sensors Add PIR Motion Sensor Delete PIR Motion Sensors Installation Main Panel Installation Door/window Sensor installation PIR Motion Sensor installation Change Dis-arm Password Low Battery Prompt Restore Factory Setting DIY Solution Q & A Tommy s Office Jenny s Cute Cafe Molly s Home Product Specification Main Panel PIR Motion Sensor: Door / Window Sensor: Wireless Remote Control: Terms of Warranty

1. Product Features 1)Main Panel works as stand alone alarm 2)Easy One-button Operation 3)4 zones for DIY home security system 4 ) W h e n t r i g g e r a l a r m s, t h e L E D i n d i c a t o r o f

left/right side of the main panel 8)Chime/alarm switch for ring tone selection 9)Stylish design fits home decoration 10)Expandable to pair up to 10 remotes, and each zone could add up to 10 sensors.

4 1. Product Features 1)Main Panel works as stand alone alarm 2)Easy One-button Operation 3)4 zones for DIY home security system 4 ) W h e n t r i g g e r a l a r m s, t h e L E D i n d i c a t o r o f correspondent zone will flash to warn you the exact alarm area 5)More safer to disarm by 4-Digital password on keypad 6)Away & home modes to set arming delay/arming 7)Support to put magnet on the left/right side of the main panel 8)Chime/alarm switch for ring tone selection 9)Stylish design fits home decoration 10)Expandable to pair up to 10 remotes, and each zone could add up to 10 sensors. D3-1 Kit includes: 1x Main Panel 4x Door/window Sensors 1x Remote Control 1x User Manual All battery and Adhesive tape 4. Button Introduction 4.1 Main panel Button 2. Operating Principle Professional DIY Security Alarm System: Built-in Magnetic Contact Sensor & PIR motion sensor which can detect any forceful break-in and activate the alarm to deter potential intruders and alerts neighbors. The LED indicator of corresponding alarm zone flashes to warn you the exact alarm area too. 3. Check Kit Accessory ARM: Short Press on button on panel, the 4 LED indicators of the panel will flash one time and beep once. 1 2

4.1.2 DISARM: Enter the default password 1234 on keypad, the 4 LED indicator of Panel will flash twice and beep twice.

3 Away Home Mode: Arm delay & Alarm delay for 30seconds (Only work for Main panel) -When you arm, the Main panel indicator will flash

And when trigger alarm, the main panel will also delay 30seconds to alarm.

5 4.1.2 DISARM: Enter the default password 1234 on keypad, the 4 LED indicator of Panel will flash twice and beep twice. (3 beep sounds indicates entering wrong password) Away Home Mode: Arm delay & Alarm delay for 30seconds (Only work for Main panel) -When you arm, the Main panel indicator will flash every second for 30seconds,then the main panel will emit a beep sound to notice you arm successfully. And when trigger alarm, the main panel will also delay 30seconds to alarm. This mode is great for you to arm when you are about to leave home without any alarms to annoy you Chime/alarm Switch (Only work for main panel) Choose Chime or alarm sound for main panel. 4.2 Remote Control Button At Home Mode: Arm directly and alarm directly when trigger alarm. (Only work for Main panel) 3 4

Quick Start by Easy Testing We have paired all the sensors to main panel already. Just do a easy testing to check the corresponding Zone for each PIR motion or Door sensor.

6 Arm Delay (After press, will arm after 30seconds) 4.4 Door/window Sensor Instruction Disarm directly after press Arm Directly after press SOS: Alarm directly after press(4 LED indicator flash) 4.3 PIR Motion Sensor Button Instruction 5. Quick Start by Easy Testing We have paired all the sensors to main panel already. Just do a easy testing to check the corresponding Zone for each PIR motion or Door sensor. Then you can install & DIY different features for each Zone for your home security system. 5.1 Check Zone for Door/Window Sensor : 1) Power on the Main panel: The battery are already loaded with a film, Just take off the film to power on the main panel. 2)Put the transmitter tightly close to magnet (Make sure the triangle marks are close to each other) 5 6

7 3) Press on main panel to ARM. 4) Separate the transmitter and magnet over than 2CM, it will trigger alarm 5)When alarm is triggered, the LED indicator of corresponding alarm zone will flash to make you quick distinguish 6. Zone Features Introduction 6.1 Features of 4 Mode Zones Please Note: Zone Features & Setting is only applicable to door sensor or PIR motion Accessory, not applicable to main panel. Ordinary Zone: When trigger alarm,the main panel will emit siren sound on the status of Arming, NO alarm sound when under disarming status. Doorbell Zone: When trigger alarm, the main panel will always emit doorbell sound no matter under arm or disarm status. Emergency Zone: When trigger alarm, the main panel will emit siren sound no matter under arm or disarm status. Welcome Zone: When trigger alarm, the main panel will emit siren sound on arming status,and emit doorbell sound on disarming status. 6.2 List of zone feature setting: 7 8

8 Zone Zone1 Zone2 Zone3 Zone4 Method Prompt Zone Mode Long press & [1] simultaneously Long press & [2] simultaneously Long press & [3] simultaneously Long press & [4] simultaneously LED indicator of Zone 1 keeps flashing LED indicator of Zone 2 keeps flashing LED indicator of Zone 3 keeps flashing LED indicator of Zone 4 keeps flashing 1. Ordinary 2. Emergency 3. Doorbell Welcome 1. Ordinary 2. Emergency 3. Doorbell Welcome 1. Ordinary 2. Emergency 3. Doorbell Welcome 1. Ordinary 2. Emergency 3. Doorbell Welcome Arm Delay or not 1.No Arming delay 2.Arm delay for30seconds 1.No Arming delay 2.Arm delay for30seconds 1.No Arming delay 2.Arm delay for30seconds 1.No Arming delay 2.Arm delay for30seconds Done Long Beep sound indicates set success fully. Then short press to quit setting. 5) Finally press button to quit setting process.done. Note: Same steps to set features for zone 2, zone 3, zone 4. 7.Expand more accessory Please Note: -It only allows to add/delete sensors on status of Disarming. Otherwise it will emit 3 beep prompt tone to notice you incorrect operation. -During learning, the short press or no operation will cause quitting learning status. 7.1 Add Remote Control 6.3 Zone Features Setting 1) Long press on button and digit [1] on the main panel simultaneously, the LED indicator of zone 1 will keep flashing, that means entering the setting process of the zone1 mode. 2) Then short Press the corresponding digital number according to the mode you need ( Ordinary Mode is 1, Emergency mode is 2, Doorbell mode is 3, Welcome Mode is 4) 3) Then short press the corresponding digital number to choose arm delay or not ( press 1 for No arming delay, press 2 for arm delay for 30seconds ) 4)After above setting done, the main panel will emit a long beep sound. Means Setting Done. 1) Long press the button on main panel, the 4 LED indicator light on, means the main panel is under learning status. 2) Press any key on remote control.the main panel LED indicator flash 2times with 2 beep sound! 3) Press on main panel to quit setting. Done! Note: -If LED indicator flashes only 1time & with 1 beep sound, means this remote control repeated. - I f L E D i n d i c a t o r fl a s h e s 3 t i m e s & w i t h 3 b e e p sound,means this remote control are already added to limitation(10pcs) -The main panel can expand remote control up to 10pcs.When main panel is on learning status,just continue to press any button on remote control 2,

7.2 Delete Remote Control 1) Long press the button on main panel, till the 4 LED indicator light on, indicates the main panel is under learning status. 2) Release pressing.

9 7.2 Delete Remote Control 1) Long press the button on main panel, till the 4 LED indicator light on, indicates the main panel is under learning status. 2) Release pressing. 3) Again long press the button on main panel, the 4 LED indicator flash 4times & with 4 Beep sounds.done! 7.3 Add Door/window Sensors 2) Put the magnet tightly close to transmitter firstly,then move the magnet away (at least 2cm far away), then put it close to transmitter again.the No.1 LED indicator will fl a s h 2 t i m e & d o o r s e n s o r e m i t s 2 t i m e s b e e p sound,means binding successfully.(if only 1 beep sound,indicates learning repeated; if 3times beep sounds,means sensors are added to limitation 10pcs already) 3) Press Press button to quit setting. Done. Tips: Same step applicable to set forzone2,zone3,zone4. Add Door/Window Sensor for Zone 1 1) Long press 1 button, No.1 LED indicator of main panel is on, indicates the main panel is under learning status. 7.4 Delete Door/window Sensors 1) Long press 1 button on main panel, No.1 LED indicator of main panel will be on, means the main panel is under learning status. 2) Release press 3) Again long Press 1 button again, the main panel indicator will flash 4times & with 4times beep sounds.all the sensors in Zone 1 are deleted. Tips: All above steps are applies for ZONE 2,ZONE 3, ZONE

7.5 Add PIR Motion Sensor 1)Long press 1 button, No.1 LED indicator of main panel is on, indicates the main panel is under learning status. 2) Place PIR motion detection lens face to you.the No.

10 7.5 Add PIR Motion Sensor 1)Long press 1 button, No.1 LED indicator of main panel is on, indicates the main panel is under learning status. 2) Place PIR motion detection lens face to you.the No.1 LED indicator will flash 2time & door sensor emits 2times beep sound,means binding successfully.if only 1 beep sound,indicates learning repeated; if 3times beep sounds,means sensors are added to limitation 10pcs already (For PIR motion detector adding,just put PIR detector face to you,it will binding successfully.) 3) Press Press button to quit setting. Done. 7.6 Delete PIR Motion Sensors 1) Long press 1 button on main panel, No.1 LED indicator of main panel will be on, means the main panel is under learning status. 2) Release press 3) Again long Press 1 button again, the main panel indicator will flash 4times & with 4times beep sounds.all the sensors in Zone 1 are deleted. Tips: All above steps are applies for ZONE 2,ZONE 3, ZONE4. 8. Installation Please Note: -Avoid installing outside where easily to be destroyed -Avoid installing closed to magnetic sources,such as heaters, air conditioner,microwave oven which may cause false triggering. 8.1 Main Panel Installation Make sure the contact works properly before installing it. 1) Main panel supports the magnet to be placed both the left and right side of main panel.make sure the main panel is close to magnet. 2) Paste the main panel and magnet separately on doors or windows or any other open/close places with provided double-sided tapes. 3) Done! Once the transmitter and magnet is separated around 2cm by intruder,the LED light in transmitter will be on in Red. Alarm will be activated. 8.2 Door/window Sensor installation Make sure the contact works properly before installing it. 4) There are triangle marks on the side of the transmitter 13 14

11 and magnet.make sure the triangle marks is close to each other. 5) Paste the transmitter and magnet separately on doors or windows or any other open/close places with provided double-sided tapes. 6) Done! Once the transmitter and magnet is separated around 2cm by intruder,the LED light in transmitter will be on in Red. Alarm will be activated. 8.3 PIR Motion Sensor installation Make sure the contact works properly before installing it. 1). Choose a suitable place for installation. 2) Fix the sensor Fix the installation bracket on the wall with screws, then fit the groove at the back of the sensor on the bracket. You can adjust bracket angle to achieve the best detection effect

12 conditioner,microwave oven which may cause false triggering. -Avoid two PIR sensors placed in the same space. There will be interference phenomenon caused by trigger at the same time if several sensors install LED in same place -Avoid installing infrared detector at outside, and it s only for indoor use. 9. Change Disarm Password 3) Mount the PIR sensor in proper angle. It s recommended to mount it at height of 2.2m from ground, and to be install LED indoors in a corner as far as possible in order to obtain the ideal detection range. The sensitivity is optimal when the walk direction is vertical to the infrared direction.choose the best location and angle according to the actual situation. 4) Pair sensor Installation Notices -Avoid infrared detectors facing to glass windows or doors; Strong light will interferes with detection sensitivity. What s more, complicated situation such as traffic flow,stream of people also should be avoided. -Avoid infrared detectors facing to or close to heat/cold sources Heat/Cold sources, such as heaters, air 1) Remove the battery of main panel 2) Keep Long pressing any digital number (except 000button) without release until battery are re-load & 6 times beep sounds & 2 times beep sounds emits,then release pressing. Now the 4 LED indicates are on. Set 4 digital password (Every pressing on digital number along with LED indicator flash 1time accordingly when you are setting password,if set password incorrectly or l o n g i n t e r v a l, t h e m a i n p a n e l w i l l q u i t s e t t i n g automatically. Then you need to re-set password) 3) Shot press to quit.done. 10.Low Battery Prompt When battery is in low power, the sound of main panel becomes weaker and trail off, LED indicator becomes weaker,either 11.Restore Factory Setting 17 18

13 1) Remove the battery of main panel 2) Keep Long pressing without release until battery are re-load & 10 times beep sounds firstly & 4 times beep sounds emits again,then release pressing. Done. Note: After Restore factory Setting, all sensors including remote control are all deleted. The main panel is on disarming status. 12. FAQ 12.1 Tommy s Office Tom: I install LED 1 pair Door sensor for zone 1 where is my office back door. I hope it will alarm immediately if someone opens after i arm the system. And keeps it silent after i disarm it. How to set zone 1 features? LOVLOY Answer: 12.2 Jenny s Cute Cafe Jenny: I run a small caf downtown.there are 2 important place, Zone 1 is the warehouse back door which i never open,so i hope it will alarm no matter i arm or disarm the system when someone break in there. And the second important area is the entrance of my caf(zone2). While i am at the work(disarm), I it would prompt me with doorbell tone when customer came in. While i go off work (Arm),it will alarm with siren when some one break in. How to set? LOVLOY Answer: Set Zone1 to be emergency Mode: Long press & key [1] + short press key [2] + short press key [1] + to quit. Set Zone 2 to be Welcome Mode. Long press & key [2] + short press key [4] + short press key [1 or 2] + to quit Set Zone1 to be Ordinary Mode. 1) Long press & key [1] immediately, then the LED indicator of zone 1 on main panel will keep flashing, means entering the process of setting of zone1. 2) Short press key [1] which means you choosed mode 1- ordinary mode 3) Then short press key [1] which means you choosed no arming delay 4) The main panel will emit a long beep sound that indicates your setting is done. 5) Finally press to quit setting Molly s Home Molly: I m a housewife, i stay at home most of the time. The balcony is my zone3, i need it alarm delay 30seconds after arming, and keep silent after disarming. The gate is my zone 4, i need it to be alarm with doorbell sound no matter in the status of arm/disarm.how to set zone 3 and zone 4 features? 19 20

14 LOVLOY Answer: Set your Zone3 to be ordinary mode by : Long press & [3] + [1]+[2]+. Set your zone4 to be doorbell mode by: Long press [4] + [3]+[1]+ Done. 13. Specifications 13.1 Main Panel: Main panel is the heart of system that is responsible for receiving and processing signal from sensors.when alarm is activated,the sound from internal siren of panel will deter intruder.. Power Supply:DC 5V Backup Battery: 3*AAA battery ( included) that support to work around 10hours,Standby 82hrs. Internal Siren Volume: 120 db Frequency:433MHz 13.2 PIR Motion Sensor: The motion detector is able to detect the temperature and movement of human body.protect any place of your house that can't be cover by contact access sensor, without opening door or window. Installation Mode :Wall mounted by bracket Operating voltage: 4.5V Transmitting Freq.: 433MHz Transmitting Distance: minimum 100m Detecting Coverage:8M,110degree field of view Installation Height: around 2.2m Battery:3*AAA battery(included) Battery lifetime: times. Would last for 6months if trigger 55times everyday & Easily monitor opening of doors and windows and any other open/close places.once opened, the transmitter and magnet will be separated and triger alarm Power Supply:23A 12V Alkaline(Included) Transmitting Distance: minimum 100m Installation: 15mm between 2 parts. Battery lifetime: 3600times.Would last for 6month if trigger 20times everyday Wireless Remote Control: With remote control,you can set arm/arm delay/disarm/sos quickly. Power Supply:CR2032 battery(included) Works at a range of around 80meter Operation Freq: 433MHz Battery lifetime: Would last for 12months. 14.Terms of Warranty 14.1 One year warranty applies to the whole system and accessory from purchasing time. The warranty doesn t apply when incorrect or improper use We make every effort to offer our customer with best product & after service. If you need any assistance,please feel free to contact us by: 13.3 Door / Window Sensor: 21 22

WIFI/PSTN Alarm System Instruction ENKLOV-W1

WIFI/PSTN Alarm System Instruction ENKLOV-W1 1 Foreword Thanks for purchasing Kerui W1 alarm system. Installing the W1 alarm system is easy and quick. Before using the product, we recommend reading the