Selectable Output Chimes and Chime/Strobes

Transcription

1 Selectable Output Chimes and Chime/Strobes PRELIMINARY DN-60940:A Audio/Visual Devices General System Sensor L-Series selectable-output chimes and chime/ strobes are rich with features guaranteed to cut installation times and maximize profits with lower current draw and modern aesthetics. The System Sensor L-Series product line of wall and ceilingmount chimes and chime strobes include a variety of features that increase their application versatility while simplifying the installation. With white and red plastic housings, System Sensor L-Series can meet virtually any application requirement. Selectable-output chimes and chime/strobes are private mode notification appliances used to alert trained personnel to investigate possible emergency situations and to take appropriate action. Security guard and nurse workstations are ideal locations for chime products. All devices feature plug-in design with minimal intrusion into the back box, making the installation fast and foolproof while virtually eliminating costly and time-consuming ground faults. Installers can easily adapt devices to a wide range of application requirements using field-selectable candela settings, automatic selection of 12-or-24 volt operation, and a rotary switch for chime tones and two volume selections. CHSCRL P2WL-P HWL Features Updated modern aesthetics Plug-in design with minimal intrusion into the back box Mounting plate shorting spring feature checks wiring continuity before device installation Captive mounting screw Tamper-resistant construction Field-selectable candela settings: Wall: 15, 30, 75, 95, 110, 135, 185 Ceiling: 15, 30, 75, 95, 115, 150, 177 Automatic selection of 12- or 24-volt operation at 15 and 30 candela Rotary switch for tone and volume selections Five selectable tones with high and low volume settings Electrically compatible with legacy SpectrAlert and SpectrAlert Advance devices Wall models listed for wall mounting only, ceiling models listed for ceiling mounting only UL 1638 listed Architect/Engineer Specifications GENERAL System Sensor L-Series chimes and chime strobes shall mount to a standard 4 4 1½-inch back box, 4-inch octagon back box, single-gang /8-inch back box, or doublegang back box. A universal mounting plate shall be used for mounting products. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, System Sensor L-Series products, when used with the Sync Circuit Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync Circuit Module, 12- volt rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC, or full-wave rectified, unfiltered power supply. Chime strobes shall have field-selectable candela settings of 15, 30, 75, 95, 110, 135, and 185 for wall units and 15, 30, 75, 95, 115, 150, and 177 for ceiling units. CHIME STROBE COMBINATION The chime strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1638 and UL 464. The chime strobe shall comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1Hz over the strobe s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The chime shall have two audibility options and an option to switch between temporal three pattern, non-temporal (continuous) pattern, 1 second chime pattern, 1/4 second chime pattern, 5 second whoop chime pattern. These options are set by a multiple position switch. SYNCHRONIZATION MODULE The module shall be a System Sensor Sync Circuit listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1Hz and all available chime tones. Also, while operating the strobes, the module shall silence the chimes on chime/strobe models over a single pair of wires. The module shall mount to a 4 11 / / / 8 -inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. PRELIMINARY DN-60940:A 12/13/2016 Page 1 of 4

2 PHYSICAL/ELECTRICAL SPECIFICATIONS Standard Operating Temperature: 32 F to 120 F (0 C to 49 C) Humidity Range: 10 to 93% non-condensing Strobe Flash Rate: 1 flash per second Nominal Voltage: Regulated 12VDC or regulated 24DC/ FWR 1 Operating Voltage Range 2 : 8 to 17.5V (12V nominal) or 16 to 33V (24V nominal) Operating Voltage Range with MLD3: 8.5 to 17.5V (12V nominal) or 16.5 to 33V (24V nominal) Input terminal wire gauge: 12 to 18 AWG Chime strobe dimensions (including lens): 5.6 in L 4.7 in W 1.25 in D (143 mm L 119 mm W 32 mm D) Chime dimensions: 5.6 in L 4.7 in W 1.25 in D (143 mm L 119 mm W 32 mm D) Ceiling Chime strobe dimensions (including lens): 6.8 in. Diameter x 2.47in. D (173.5mm Diameter x 62.7mm D) SBBRL (red wall surface mount back box): 5.6 in L 4.7 in W 4.3 in D (142 mm L 119 mm W 109 mm D) SBBWL (white wall surface mount back box): 5.6 in L 4.7 in W 4.3 in D (142 mm L 119 mm W 109 mm D) SBBCRL (red ceiling surface mount back box): 6.9 in. Dia. x 2.5in. D (175.8mm Dia. x 63.5mm) SBBCWL (white ceiling surface mount back box): 6.9in. Dia. x 2.5in. D (175.8mm Dia. x 63.5mm) Notes: 1. Full Wave Rectified (FWR) voltage is a non-filtered, time varying power source that is used on some power supply and panel outputs. 2. CHS products will operate at 12 V nominal only for 15 and 30. Tone Selection Chime tone selection is accomplished by using the rotary switch on the back of the product. The current draw and sound measurements for various chime tone settings are listed below. CHIME PATTERNS Setting Repetition Rate db Level 1 1 Second Chime High 2 1 Second Chime Low 3 ¼ Second Chime High 4 ¼ Second Chime Low 5 Temporal Chime High 6 Temporal Chime Low 7 5 Second Whoop High 8 5 Second Whoop Low 9 Coded** High **For chime only. CHIME AND CHIME/STROBE OUTPUT (DBA) Switch Position Sound Pattern db Volts Volts DC DC FWR 1 1 Second Chime High Second Chime Low ¼ Second Chime High ¼ Second Chime Low Temporal Chime High Temporal Chime Low Second Whoop High Second Whoop Low Coded** High **For chime only. UL Current Draw Data UL MAX. CHIME CURRENT DRAW (MA RMS) Volts Volts Sound Pattern db DC DC FWR 1 Second Chime High Second Chime Low /4 Second Chime High /4 Second Chime Low Temporal Chime High Temporal Chime Low Second Whoop High Second Whoop Low Coded High * 1 Second Chime High *This data represents coding at 3 chimes per second. Actual current draw will vary depending upon coding selected. Page 2 of 4 DN-60940:A 12/13/2016PRELIMINARY

3 UL MAX. CHIME/STROBE CURRENT DRAW (MA RMS) WALL Volts Volts DC Input Second Chime Second Chime /4 Second Chime /4 Second Chime Temporal Chime Temporal Chime Second Whoop Second Whoop Volts FWR Input Second Chime Second Chime /4 Second Chime /4 Second Chime Temporal Chime Temporal Chime Second Whoop Second Whoop UL MAX. CHIME/STROBE CURRENT DRAW (MA RMS) CEILING Volts Volts DC Input Second Chime Second Chime /4 Second Chime /4 Second Chime Temporal Chime Temporal Chime Second Whoop Second Whoop Volts FWR Input Second Chime Second Chime /4 Second Chime /4 Second Chime Temporal Chime Temporal Chime Second Whoop Second Whoop PRELIMINARY DN-60940:A 12/13/2016 Page 3 of 4

4 Product Drawings: Dimensions Chime Chime Strobe Ceiling Chime Strobe SBBCRL(A) SBBCRL(A) 60940dimensions.eps Agency Listings and Approvals L-series devices have been submitted for agency approvals. Consult factory for latest listing status. Product Line Information Note: A model devices are ULC listed and include required French labeling. CHWL(A), CHRL(A). Chime, Wall (White, Red). CHSWL(A), CHSRL(A). Chime Strobe, Wall (White, Red). CHSCWL(A), CHSCRL(A). Chime Strobe, Ceiling (White, Red). ACCESSORIES SBBWL, SBBRL. Surface Mount Back Box, Wall (White, Red). SBBCWL, SBBCRL. Surface Mount Back Box, Ceiling.(White, Red). Page 4 of 4 DN-60940:A 12/13/2016PRELIMINARY

5 Indoor Selectable-Output Strobes and Horn Strobes for Ceiling Applications PRELIMINARY DN-60938:A Audio/Visual Devices General System Sensor L-Series audible visible notification products are rich with features guaranteed to cut installation times and maximize profits with lower current draw and modern aesthetics. The System Sensor L-Series offers the most versatile and easy-to-use line of horns, strobes, and horn strobes in the industry with lower current draws and modern aesthetics. With white and red plastic housings, wall and ceiling mounting options, System Sensor L-Series can meet virtually any application requirement. The entire L-Series product line of ceiling-mount strobes and horn strobes include a variety of features that increase their application versatility while simplifying installation. All devices feature a plug-in design with minimal intrusion into the back box, making installations fast and foolproof while virtually eliminating costly and time-consuming ground faults. To further simplify installation, the L-Series utilizes a universal mounting plate so installers can mount them to a wide array of back boxes. With an onboard shorting spring, installers can test wiring continuity before the device is installed. Installers can also easily adapt devices to a suit a wide range of application requirements using field-selectable candela settings, automatic selection of 12- or 24-volt operation, and a rotary switch for horn tones with two volume selections. Features Plug-in design with minimal intrusion into the back box Tamper-resistant construction Automatic selection of 12- or 24-volt operation at 15 and 30 candela Field-selectable candela settings on ceiling units: 15, 30, 75, 95, 115, 150, and 177 Horn rated at 88+ dba at 16 volts Rotary switch for horn tone and two volume selections Universal mounting plate for ceiling units Mounting plate shorting spring feature checks wiring continuity before device installation Electrically compatible with legacy SpectrAlert and SpectrAlert Advance devices Compatible with MDL3 sync module Listed for ceiling mounting only SCRL PC2WL Architect/Engineer Specifications GENERAL L-Series ceiling-mount strobes and horn strobes shall mount to a standard 4 4 1½-inch back box, 4-inch octagon back box, or double-gang back box. Two-wire products shall also mount to a single-gang / 8 inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, L-Series products, when used with the Sync Circuit Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24- volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply. Ceiling strobes and horn strobes shall have field-selectable candela settings including 15, 30, 75, 95, 115, 150, and 177. STROBE The strobe shall be a System Sensor L-Series Model listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/ reflector system. HORN STROBE COMBINATION The horn strobe shall be a System Sensor L-Series Model listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have two audibility options and an option to switch between a temporal three pattern and a non-temporal (continuous) pattern. These options are set by a multiple position switch. The horn on horn strobe models shall operate on a coded or noncoded power supply. PRELIMINARY DN-60938:A 12/13/2016 Page 1 of 4

6 SYNCHRONIZATION MODULE The module shall be a System Sensor Sync Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize L-Series strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn strobe models over a single pair of wires. The module shall mount to a 4 11 / / / 8 inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. PHYSICAL/ELECTRICAL SPECIFICATIONS Standard Operating Temperature: 32 F to 120 F (0 C to 49 C) Humidity Range: 10 to 93% non-condensing Strobe Flash Rate: 1 flash per second Nominal Voltage: Regulated 12VDC or regulated 24DC/ FWR 1 Operating Voltage Range 2 : 8 to 17.5V (12V nominal) or 16 to 33V (24V nominal) Operating Voltage Range with MLD3: 8.5 to 17.5V (12V nominal) or 16.5 to 33V (24V nominal) Input terminal wire gauge: 12 to 18 AWG Ceiling-Mount Dimensions (including lens): 6.8" diameter 2.5" high (173 mm diameter 64 mm high) Ceiling-Mount Surface Mount Back Box Skirt Dimensions (SBBCR, SBBCW): 6.9" diameter x 3.4" high (175 mm diameter x 86 mm high) Notes: 1. Full Wave Rectified (FWR) voltage is a non-filtered, time varying power source that is used on some power supply and panel outputs. 2. P, S, PC, and SC products will operate at 12 V nominal only for 15 and 30. UL Current Draw Data UL MAX. STROBE CURRENT DRAW (MA RMS) Volts Volts Candela DC DC FWR N/A N/A N/A N/A N/A *This data represents coding at 3 chimes per second. Actual current draw will vary depending upon coding selected. Page 2 of 4 DN-60938:A 12/13/2016PRELIMINARY

7 UL MAX. CHIME/STROBE CURRENT DRAW (MA RMS), 2-WIRE HORN STROBE 8 VDC 16 VDC Candela EM Temp Hi EM Temp Low EM Cont Hi EM Cont Low K Temp Hi K Temp Low K Cont Hi K Cont Low VFWR Candela EM Temp Hi EM Temp Low EM Cont Hi EM Cont Low K Temp Hi K Temp Low K Cont Hi K Cont Low Horn Strobe Tones and Sound Output Data HORN AND HORN STROBE OUTPUT (DBA) Volts Volts Switch Position Sound Pattern db DC DC FWR 1 Temporal High Temporal Low Non-Temporal High Non-Temporal Low KHz Temporal High KHz Temporal Low KHz Non-Temporal High KHz Non-Temporal Low PRELIMINARY DN-60938:A 12/13/2016 Page 3 of 4

8 Product Drawings: L-Series Dimensions oly_ceil_horn_strobe_datasheet_ _ol.eps Ceiling-mount horn strobes Ceiling back box surface mount back box Agency Listings and Approvals L-series devices have been submitted for agency approvals. Consult factory for latest listing status. Product Line Information Note: A model devices are ULC listed and include required French labeling. CEILING HORN STROBES PC2WL(A), PC2RL(A). 2-Wire, Horn Strobe (White, Red). CEILING STROBES SCWL(A), SCRL(A). Strobe (White, Red). SCWL-CLR-ALERT(A). Strobe, ALERT (White). ACCESSORIES TR-2W, TR-2. Universal Wall Trim Ring (White, Red). SBBCWL, SBBCRL. Ceiling Surface Mount Back Box (White, Red). NOTIFIER and SpectrAlert are registered trademarks and Sync Circuit is a trademark of Honeywell International Inc by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. Page 4 of 4 DN-60938:A 12/13/2016PRELIMINARY This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) , FAX: (203)

9 Indoor Selectable-Output Speaker Strobes and Dual Voltage Evacuation Speakers for Wall Applications General System Sensor L-Series selectable output speaker strobes and dual-voltage evacuation speakers can reduce ground faults and enable faster installation with lower current draw and modern aesthetics. The System Sensor L-Series of speakers and speaker strobes reduce costly ground faults using a plug-in design and universal mounting plate that allow the installer to pre-wire mounting plates, dress the wires, and confirm wiring continuity before plugging in the speakers. In addition, a protective plastic cover prevents nicked wires by covering exposed speaker components. These devices also enable faster installations by providing instant feedback to ensure that wiring is properly connected, rotary switches to select voltage and power settings, and 7 field-selectable candela settings for wall speaker strobes. The low total harmonic distortion of the speaker offers high fidelity sound output while still offering high volume sound output for use in high ambient noise applications. System Sensor L-Series makes installation easy. Attach a universal mounting plate to a / 8 inch back box. Flush-mount applications do not require an extension ring. Connect the notification appliance circuit or speaker wiring to the terminals on the mounting plate. Attach the speaker or speaker strobe to the mounting plate by inserting the product tabs into the mounting plate grooves. Hinge the device into position to lock the product pins into the mounting plate terminals. The device will temporarily hold in place with a catch until it is secured with a captured mounting screw. Features Plug-in design and protective cover reduce ground faults Universal mounting plate with an onboard shorting spring tests wiring continuity before installation No extension ring required Field selectable candela settings on wall units: 15, 30, 75, 95, 110, 135, 185 Automatic selection of 12- or 24-volt operation at 15 and 30 candela Rotary switch simplifies field selection of speaker voltage (25 and 70.7 Vrms) and power settings (¼, ½, 1 and 2 watts) Speakers offer high fidelity and high volume sound output Compatible with System Sensor synchronization protocol Electrical compatibility with existing SpectrAlert and SpectrAlert Advance products Tamper-resistant construction Updated modern aesthetics SPSWL PRELIMINARY DN-60942:A Audio/Visual Devices SPSRL Architectural/Engineering Specifications GENERAL L-Series speaker and speaker strobes shall mount to a / 8 inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit and amplifier wiring shall terminate at the universal mounting plate. Also, L-Series speaker strobes, when used with the Sync Circuit Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync Circuit Module, 12-volt rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor L-Series products shall operate between 32 F and 120 F from a regulated DC, or full-wave rectified, unfiltered power supply. Wall-mount speaker strobes shall have field-selectable candela settings including 15, 30, 75, 95, 110, 135, 185. SPEAKER The speaker shall be a System Sensor L-Series model dual-voltage transformer speaker capable of operating at 25.0 or 70.7 nominal Vrms. It should be listed to UL 1480 and shall be approved for fire protective service. The speaker shall have a frequency range of 400 to 4,000 Hz and shall have an operating temperature between 32 F and 120 F. The speaker shall have power taps and voltage that are selected by rotary switches. SPEAKER STROBE COMBINATION The speaker strobe shall be a System Sensor L-Series model listed to UL1480 and UL 1971 and be approved for fire protective signaling systems. The speaker shall be capable of operating at 25.0 or 70.7 nominal Vrms selected via rotary switch, and shall have a frequency range of 400 to 4,000 Hz. The speaker shall have power taps that are selected by rotary switch. The strobe shall comply with the NFPA 72 requirements for visible signaling appliances, flashing at 1 Hz over the strobe s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/ reflector system. SYNCHRONIZATION MODULE The module shall be a System Sensor Sync Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 PRELIMINARY DN-60942:A 12/13/2016 Page 1 of 4

10 Hz. The module shall mount to a 4 11 / / / 8 inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. PHYSICAL/ELECTRICAL SPECIFICATIONS Standard Operating Temperature: 32 F to 120 F (0 C to 49 C) Humidity Range: 10 to 93% non-condensing DIMENSIONS, WALL-MOUNT SP Speaker: 6.5 in x 5 in x 2.3 in. (165 mm x 127 mm x 58 mm) SP Speaker with Surface Mount Back Box: 6.6 in x 5.1 in x 3.2 in (168 mm x 130 mm x 82 mm) SPS Speaker/Strobe (including lens and speaker): 6.5 in x 5.0 in x 2.3 in (165 mm x 127 mm x 58 mm) SPS Speaker/Strobe (including lens and speaker) with Surface Mount Back Box: 6.6 in x 5.1 in x 4.55 in. (168 mm x 130 mm x 116 mm) ELECTRICAL/OPERATING SPECIFICATIONS: Nominal Voltage (speakers): 25 or 70.7 (nominal) Maximum Supervisory Voltage (speakers): 50 VDC Strobe Flash Rate: 1 flash per second Nominal Voltage (strobes): Regulated 12 VDC or regulated 24 DC/FWR Operating Voltage Range (includes fire alarm panels with built in sync): 8 to 17.5 V (12 V nominal) or 16 to 33V (24 V nominal) Operating Voltage with MDL3 Sync Module: 8.5 to 17.5 V (12 V nominal) or 16.5 to 33V (24 V nominal) Frequency Range: 400 to 4000 Hz Power: ¼, ½, 1, 2 watts UL Current Draw Data UL MAX. STROBE CURRENT DRAW (MA RMS) Candela DC DC FWR N/A N/A N/A N/A N/A SOUND OUTPUT SPEAKER STROBE ¼ W ½ W 1 W 2 W UL Reverberant ft) UL Anechoic ft) SOUND OUTPUT SPEAKER UL Reverberant ft) UL Anechoic ft) Volts Volts Agency Listings and Approvals L-series devices have been submitted for agency approvals. Consult factory for latest listing status. Product Line Information ¼ W ½ W 1 W 2 W Note: A model devices are ULC listed and include required French labeling. WALL MOUNT SPWL(A), SPRL(A). Speaker only (White, Red). SPSWL(A), SPSRL(A). Speaker Strobe (White, Red). SPSWL-P(A), SPSRL-PL(A). Plain Speaker Strobe (White, Red). SPSWL-ALERT. Speaker Strobe, Amber Lens (White). SPSWL-CLR-ALERT(A). Speaker Strobe Clear Lens (White). SPSRL-SP. Speaker Strobe, Fuego (White). ACCESSORIES RFPW, RFP. 7 in 9.5 in Retrofit Plate (White, Red). SBBSPW, SBBSPR. Surface Mount Back Box for Speakers and Speaker Strobes (White, Red). TRW, TR. Wall Mount Trim Ring (White, Red). Page 2 of 4 DN-60942:A 12/13/2016PRELIMINARY

11 Product Drawings: Dimensions and Surface Mounting Wall-Mount Speaker Wall-Mount Speaker Strobe 60942dimensions.eps Wall-Mount Speaker Strobe with SBBSPRL Surface Mount Back A eps PRELIMINARY DN-60942:A 12/13/2016 Page 3 of 4

12 NOTIFIER and SpectrAlert are registered trademarks and Sync Circuit is a trademark of Honeywell International Inc by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. Page 4 of 4 DN-60942:A 12/13/2016PRELIMINARY This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) , FAX: (203)

13 L-series Audible Visible Accessories PRELIMINARY DN-60944:A Audio/Visual Devices General L-Series devices offer a wide range of Audible Visible (AV) accessories to meet a variety of application requirements. The MP120KL Mounting Plate is designed to use 120 VAC to power SpectrAlert Advance horns, strobes, horn strobes, chimes, and chime strobes. Color Lens Attachments install easily on any L-Series strobe devices to provide distinctive visual signaling. Bezel Kits enable installers to easily turn any L-Series Fire or Plain device into a device that meets ECS/MNS requirements. Bezel kits are available for all varieties and footprints of L- Series products and come in FIRE, ALERT, EVAC, AGENT, FUEGO, FOGO, and Plain options making customization easy. Universal Trim Rings for wall and ceiling mount devices allow for additional space within the backbox. L-Series Surface Mount Back Boxes are the best solution in locations where you have a hard surface to mount to. The Sync Circuit Module synchronizes L-Series strobes at 1 Hz and horns and chimes at temporal 3 over a single pair of wires. Patented module technology also allows the silencing of horns or chimes on horn strobe and chime strobe models over a pair of wires. See the Sync Circuit Datasheet for more information. Features MP120KL MOUNTING PLATE Designed for both indoor and outdoor use Plug-in design eliminates ground faults Power supply that converts 120 VAC to nominal 24 V FWR Compatible with all two-wire L-Series devices COLOR LENS ATTACHMENTS Easily turns any device into a strobe for ECS/MNS events: severe weather, toxic gases, sprinkler activation and more Outdoor rated from -35 F to 151 F Wall- or ceiling-mount lenses available UL 1638 listed BEZEL KITS Easily turn a Fire or Plain device into a device to meet ECS/ MNS requirements Bezel kits available for strobes, horns, chimes, horn strobes, chime strobes and speaker strobes Bezels options with FIRE, ALERT, EVAC, AGENT, PLAIN, FUEGO, FOGO printing For use with L-Series devices only Operating temperature -40 F to 151 F AV Accessories Family: Mouting Plate, Red Fire Bezel, and Colored Lenses MP120K Specifications 120 VAC mounting plate model MP120KL shall be listed to UL 464 for fire-protective signaling systems. The mounting plate shall power a two-wire L-Series horn, strobe, horn strobe, chime or chime strobe from a 120 VAC supply converted to nominal 24 V FWR. For indoor applications, the mounting plate shall be installed in a 4x4x2 1 / 8 inch junction box. MK120KL COMPATIBILITY MP120KL may be used with any of the following products at all horn and strobe settings: P2RL, P2WL, P2RL-P, P2WL-P, P2RL-SP, P2WL-SP, PC2RL, PC2WL, SRL, SWL, SRL-P, SWL-P, SRL-SP, SWL-CLR-ALERT, SWL-ALERT, SCRL, SCWL, SCWL-CLR-ALERT, HRL, HWL, CHRL, CHWL, CHSRL, CHSWL, CHSCRL, CHSCWL. MP120K PHYSICAL/OPERATING SPECIFICATIONS Operating Temperature: 40 F to 151 F ( 40 C to 66 C). Humidity Range: 10 to 93% non-condensing (indoor products). Nominal Voltage: Regulated 120 VAC Operating Voltage Range: VAC Current Draw From AC Line: 150 ma max. L-Series Bezels Specifications The System Sensor L-Series bezels are for installation with strobes, horns, chimes, horn strobes, chime strobes, and speaker strobes. Bezels are offered in red and white for both wall and ceiling devices. Available in FIRE, ALERT, EVAC, AGENT, Plain (no marking), FUEGO, and FOGO. Operating temperature shall be -40 F to 151 F. Colored Lens Attachments ARCHITECTURAL/ENGINEERING SPECIFICATIONS The System Sensor L-Series colored lens attachments shall be approved for fire-protective service as listed in UL The lens attachments shall only be used with plain (no FIRE print) System Sensor strobe devices or in conjunction with a non-fire printed bezel. The lens shall mount to any wall- or ceiling-mount strobes and shall be rated from -35 F to 151 F. PRELIMINARY DN-60944:A 12/13/2016 Page 1 of 2

14 COMPATIBILITY Colored lens attachments may be used with the following System Sensor L-Series plain (non-fire-printed) strobe models: P2RL-P, P2WL-P, SRL-P, SWL-P, SPSRL-P, SPSWL-P, SPSCWL-P, or any device used with a non-fire printed bezel. Agency Listings and Approvals L-series devices have been submitted for agency approvals. Consult factory for latest listing status. Product Line Information Note: A model devices are ULC listed and include required French labeling. SYNC MODULES MDL3W(A), MDL3R(A). 12/24 volt Sync Circuit module (White, Red). TRIM RINGS TR-2W, TR-2. Universal wall trim ring (White, Red). TRC-2W, TRC-2. Universal ceiling trim ring (White, Red). Product Drawings INSTALLING COLORED LENSES SURFACE MOUNT BACK BOX SBBWL, SBBRL. Wall-mount, compatible with standard horns, strobes, horn strobes, chimes and chime strobes (White, Red). SBBSPWL, SBBSPRL. Wall-mount, compatible with speakers and speaker strobes (White, Red). SBBCWL, SBBCRL. Ceiling-mount compatible with horns, strobe, horn strobes, chimes, chime strobes, speakers and speaker strobes.(white, Red). SBBGWL, SBBGRL. Wall-mount, compatible with compact horns, strobes, horn strobes (White, Red). BEZELS* BZW, BZR. Wall Red Bezel Kit (White, Red). BZGW, BZGR. Compact Wall Red Bezel Kit (White, Red). BZWC, BZRC. Horn Strobe Ceiling Red Bezel Kit (White, Red). BZSPW, BZSPR. Speaker Wall Red Bezel Kit (White, Red). BZSPWC, BZSPRC. Speaker Ceiling Red Bezel Kit (White, Red). *Each bezel pack ships in a package of 5. For desired bezel option add -F (FIRE), -AL (ALERT), -EV (EVAC), -AG (AGENT), -P (Plain), -SP (FUEGO), -PG (FOGO) for desired printing. COLORED LENSES LENS-B2. Wall-mount, blue. LENS-R2. Wall-mount, red. LENS-G2. Wall-mount, green. LENS-A2. Wall-mount, amber. LENS-BC2. Ceiling-mount, blue. LENS-RC2. Ceiling-mount, red. LENS-GC2. Ceiling-mount, green. LENS-AC2. Ceiling-mount, amber. Wall-Mounted Strobe INSTALLING BEZELS Wall-Mounted Strobe Ceiling-Mounted Strobe LensWallLSeries.png, LensCeilingLSeries.png Ceiling-Mounted Strobe BezelWallLSeries.png, BezelCeilingLSeries.png RETROFIT PLATES (For use with horn strobe & speaker strobe devices) RFPW, RFP. 9.5" x 7" (White, Red). MOUNTING PLATE MP120KL(A). 120 VAC Adapter Mounting Plate NOTIFIER and SpectrAlert are registered trademarks and Sync Circuit is a trademark of Honeywell International Inc by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. Page 2 of 2 DN-60944:A 12/13/2016PRELIMINARY This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) , FAX: (203)

15 Indoor Selectable-Output Speaker Strobes and Dual Voltage Evacuation Speakers for Ceiling Applications General The L-Series of speakers and speaker strobes reduce costly ground faults using a plug-in design and universal mounting plate. The installer can pre-wire mounting plates, dress the wires, and confirm wiring continuity before plugging in the speakers. In addition, a protective plastic cover prevents nicked wires by covering exposed speaker components. These devices also enable faster installations by providing instant feedback to ensure that wiring is properly connected, rotary switches to select voltage and power settings, and 7 field-selectable candela settings for both wall and ceiling speaker strobes. The low total harmonic distortion of the SP speaker offers high fidelity sound output while still offering high volume sound output for use in high ambient noise applications. L-SERIES MAKES INSTALLATION EASY Attach a universal mounting plate to a 4" 4" 2 1 / 8 " back box. Flush-mount applications do not require an extension ring. Connect the notification appliance circuit or speaker wiring to the terminals on the mounting plate. Attach the speaker or speaker strobe to the mounting plate by inserting the product tabs into the mounting plate grooves. Hinge the device into position to lock the product pins into the mounting plate terminals. The device will temporarily hold in place with a catch until it is secured with a captured mounting screw. Features Plug-in design and protective cover reduce ground faults. Universal mounting plate with an onboard shorting spring tests wiring continuity before installation. No extension ring required. Field selectable candela settings on ceiling units: 15, 30, 75, 95, 115, 150, and 177. Automatic selection of 12- or 24-volt operation at 15 and 30 candela. Rotary switch simplifies field selection of speaker voltage (25 and 70.7 Vrms) and power settings (¼, ½, 1 and 2 watts). Speakers offer high fidelity and high volume sound output. Compatible with System Sensor synchronization protocol. Electrical compatibility with existing SpectrAlert and SpectrAlert Advance products. Tamper-resistant construction. Updated modern aesthetics. SPSCRL, SPSCWL PRELIMINARY DN-60924:A Audio/Visual Devices Architectural/Engineering Specifications General. L-Series speaker and speaker strobes shall mount to a 4" 4" 2 1 / 8 " back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit and amplifier wiring shall terminate at the universal mounting plate. Also, L-Series speaker strobes, when used with the Sync Circuit Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync Circuit Module, 12-volt rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor L-Series products shall operate between 32 F and 120 F from a regulated DC, or full-wave rectified, unfiltered power supply. Speaker strobes shall have field-selectable candela settings including 15, 30, 75, 95, 115, 150, 177. Speaker. The speaker shall be a System Sensor L-Series model dual-voltage transformer speaker capable of operating at 25.0 or 70.7 nominal Vrms. It should be listed to UL 1480 and shall be approved for fire protective service. The speaker shall have a frequency range of 400 to 4,000 Hz and shall have an operating temperature between 32 F and 120 F. The speaker shall have power taps and voltage that are selected by rotary switches. Speaker Strobe Combination. The speaker strobe shall be a System Sensor L-Series modellisted to UL1480 and UL 1971 and be approved for fire protective signaling systems. The speaker shall be capable of operating at 25.0 or 70.7 nominal Vrms selected via rotary switch, and shall have a frequency range of 400 to 4,000 Hz. The speaker shall have power taps that are selected by rotary switch. The strobe shall comply with the NFPA 72 requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Synchronization Module. The module shall be a System Sensor Sync Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz. The module shall mount to a 4 11 / 16 " 4 11 / 16 " 2 1 / 8 " back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining PRELIMINARY DN-60924:A 12/13/2016 Page 1 of 4

16 two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Physical Specifications Standard Operating Temperature: 32 F to 120 F (0 C to 49 C). Humidity Range: 10 to 93% non-condensing. Dimensions, Ceiling-Mount: SPC Speaker: Diameter 6.8 in, 173 mm. Depth: 1.0 in, 25 mm. SPC Speaker with Surface Mount Back Box: Diameter: 6.9 in, 176 mm. Depth: 3.5 in, 89 mm. SPSC Speaker Strobe: Diameter: 6.8 in, 173 mm. Depth: 2.8 in, 73 mm. SPSC Speaker Strobe with Surface Mount Back Box: Diameter 6.9 in, 176 mm. Depth: 5.37 in, 136 mm. Electrical/Operating Specifications Nominal Voltage (speakers): 25 Volts or 70.7 Volts (nominal). Maximum Supervisory Voltage (speakers): 50 VDC. Strobe Flash Rate: 1 flash per second. Nominal Voltage (strobes): Regulated 12 DC or regulated 24 DC/FWR (full wave rectified). Operating Voltage Range (includes fire alarm panels with built in sync): 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal). Operating Voltage with MDL3 Sync Module: 8.5 V to 17.5 V (12 V nominal) or 16.5 V to 33 V (24 V nominal). Frequency Range: 400 to 4,000 Hz. Power: ¼, ½, 1, 2 watts. CEILING-MOUNT SPEAKER STROBE SOUND OUTPUT Setting UL Reverberant ft) UL Anechoic ft) ¼ W ½ W W W Agency Listings and Approvals L-series devices have been submitted for agency approvals. Consult factory for latest listing status. Product Line Information Note: A model devices are ULC listed and include required French labeling. CEILING MOUNT SPEAKER STROBES SPCWL(A), SPCRL(A). Speaker only (White, Red). SPSCWL(A), SPSCRL(A). Speaker strobe (White, Red). SPSCWL(A)-P. Plain speaker strobe (White). SPSCWL-SP. Spanish-labeled Fuego speaker strobe (White). SPSCWL-CLR-ALERT(A). Alert model speaker strobe with clear lens (White). ACCESSORIES SBBCWL, SBBCRL. Universal Ceiling Surface Mount Back Box (White, Red). TRC-2W, TRC-2. Universal Ceiling Trim Ring (White, Red). UL Current Draw Data UL MAX. STROBE CURRENT DRAW (MA RMS) Volts Volts Candela DC DC FWR NA NA NA NA NA CEILING-MOUNT SPEAKER SOUND OUTPUT Setting UL Reverberant ft) UL Anechoic ft) ¼ W ½ W W W Page 2 of 4 DN-60924:A 12/13/2016PRELIMINARY

17 Product Drawings 1.63'' (4.14 cm) A eps 2.87'' (7.29 cm) 1.76'' (4.47 cm) 6.80'' diameter ( cm) Speaker Strobe Dimensions Speaker Strobe with SBBCRL/ SBBCWL Surface Mount Back Box 1.00'' (2.54 cm) 1.63'' (4.14 cm) A eps 6.80'' diameter ( cm) Speaker Dimensions Speaker with SBBCRL/SBBCWL Surface Mount Back Box PRELIMINARY DN-60924:A 12/13/2016 Page 3 of 4

18 NOTIFIER and SpectrAlert are registered trademarks and Sync Circuit is a trademark of Honeywell International Inc by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. Page 4 of 4 DN-60924:A 12/13/2016PRELIMINARY This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) , FAX: (203)

19 Indoor Selectable-Output Horns, Strobes, and Horn Strobes for Wall Applications General The L-Series offers the most versatile and easy-to-use line of horns, strobes, and horn strobes in the industry with lower current draws and modern aesthetics. With white and red plastic housings, standard and small footprint devices, and plain, FIRE-printed devices, L-Series can meet virtually any application requirement. The L-Series product line of wall-mount horns, strobes, and horn strobes include a variety of features that increase their application versatility while simplifying installation. All devices feature plug-in designs with minimal intrusion into the back box, making installations fast and foolproof while virtually eliminating costly and time-consuming ground faults. To further simplify installation and protect devices from construction damage, L-Series utilizes a universal mounting plate for all standard and compact models with an onboard shorting spring, so installers can test wiring continuity before the device is installed. Installers can also easily adapt devices to a suit a wide range of application requirements using field-selectable candela settings, automatic selection of 12- or 24-volt operation, and a rotary switch for horn tones with two volume selections. P2RL PRELIMINARY DN-60918:A Audio/Visual Devices Features Updated modern aesthetics. Small profile devices for Horns and Horn Strobes. Plug-in design with minimal intrusion into the back box. Tamper-resistant construction. Automatic selection of 12- or 24-volt operation at 15 and 30 candela. Field-selectable candela settings on wall units: 15, 30, 75, 95, 110, 135, and 185. Horn rated at 88+ dba at 16 volts. Rotary switch for horn tone and two volume selections. Universal mounting plate for all standard and all compact wall units. Mounting plate shorting spring checks wiring continuity. before device installation. Electrically Compatible with legacy SpectrAlert and SpectrAlert Advance devices. Compatible with MDL3 sync module. Listed for wall mounting only. Architectural/Engineering Specifications General: L-Series standard horns, strobes, and horn strobes shall mount to a standard 2" x 4" x 1 7 / 8 " back box, 4" 4" 1½" back box, 4" octagon back box, or double-gang back box. L-Series compact products shall mount to a single-gang 2" 4" 1 7 / 8 " back box. A universal mounting plate shall be used for mounting ceiling and wall products for all standard-size models and a separate universal mounting plate shall be used for mounting compact wall models. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, L-Series products, when used with the Sync Circuit Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal P2GWL HWL SGWL 12 or 24 volts. When used with the Sync Circuit Module, 12- volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt-rated c appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unaltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15, 30, 75, 95, 110, 135, and 185. Strobe. The strobe shall be a L-Series Model listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/ reflector system. PRELIMINARY DN-60918:A 12/13/2016 Page 1 of 4

20 Horn Strobe Combination. The horn strobe shall be a L-Series Model listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have two audibility options and an option to switch between a temporal three pattern and a non-temporal (continuous) pattern. These options are set by a multiple position switch. The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module. The module shall be a Sync Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn strobe models over a single pair of wires. The module shall mount to a 4 11 / 6 " 4 11 / 16 " 2 1 / 8 " back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. PHYSICAL/ELECTRICAL SPECIFICATIONS Standard Operating Temperature: 32 F to 120 F (0 C to 49 C). Humidity Range: 10 to 93% non-condensing. Strobe Flash Rate: 1 flash per second. Nominal Voltage: Regulated 12 DC or regulated 24 DC/ FWR 1 (full wave rectified). Operating Voltage Range 2 : 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal). Operating Voltage Range: MDL3 Sync Module 8.5 to 17.5 V (12 V nominal) or 16.5 to 33 V (24 V nominal). Input Terminal Wire Gauge: 12 to 18 AWG. Wall-Mount Dimensions (including lens): 5.6" L 4.7" W 1.25" D (143 mm L 119 mm W 32 mm D). Compact Wall-Mount Dimensions (including lens): 5.26 L x 3.46 W x 1.93 D (133 mm L x 88 mm W x 49 mm D). Horn Dimensions: 5.6" L 4.7" W 1.25" D (143 mm L 119 mm W 32 mm D). Compact Horn Dimensions: 5.25 L x 3.45 W x 1.25 D (133mm L x 88mm W x 32mm D). Notes: 1. Full Wave Rectified (FWR) voltage is a non-regulated, timevarying power source that is used on some power supply and panel outputs. 2. P, S, PC, and SC products will operate at 12 V nominal only for 15 and 30. L-Series Drawings Compact Horn Compact Combo Horn Combo Page 2 of 4 DN-60918:A 12/13/2016PRELIMINARY

21 UL Current Draw Data UL MAX. STROBE CURRENT DRAW (MA RMS) Volts Volts Candela DC DC FWR N/A N/A N/A N/A N/A UL MAX. HORN CURRENT DRAW (MA RMS) Volts Volts Sound Pattern db DC DC FWR Temporal High Temporal Low Non-Temporal High Non-Temporal Low KHz Temporal High KHz Temporal Low KHz Non-Temporal High KHz Non-Temporal Low Coded High KHz Coded High UL MAX. CURRENT DRAW (MA RMS), 2-WIRE HORN STROBE, CANDELA RANGE ( CD) DC Input: Volts DC Input: Volts FWR Input: 16 FWR EM Temp Hi EM Temp Low EM Cont Hi EM Cont Low K Temp Hi K Temp Low K Cont Hi k Cont Low HORN TONES AND SOUND OUTPUT DATA: HORN AND HORN STROBE OUTPUT (DBA) Volts Volts Pos. Sound Pattern db DC DC FWR 1 Temporal High Temporal Low Non-Temporal High Non-Temporal Low KHz Temporal High KHz Temporal Low KHz Non-Temporal High KHz Non-Temporal Low Coded High KHz Coded High PRELIMINARY DN-60918:A 12/13/2016 Page 3 of 4

22 Agency Listings and Approvals L-series devices have been submitted for agency approvals. Consult factory for latest listing status. Product Line Information Note: A model devices are ULC listed and include required French labeling. WALL HORN STROBES P2WL(A), P2RL(A). 2-Wire, Horn Strobe (White, Red). P2GWL(A), P2GRL(A). 2-Wire, Compact Horn Strobe (White, Red). P2WL(A)-P, P2RL(A)-P. 2-Wire, Horn Strobe, Plain (White, Red). P2WL-SP, P2RL-SP. 2-Wire, Horn Strobe, FUEGO (White, Red). WALL STROBES SWL(A), SRL(A). Strobe, Red (White, Red). SGWL(A), SGRL(A). Compact Strobe (White, Red). SWL(A)-P, SRL(A)-P. Strobe, Plain (White, Red). SRL-SP. Strobe, FUEGO (Red). SWL-CLR-ALERT(A). Strobe, ALERT (White). SWL-ALERT(A). Strobe, Wall, Amber Lens, Alert (White). HORNS HWL(A), HRL(A). Horn (White, Red). HGWL(A), HGRL(A). Compact Horn (White, Red). ACCESSORIES TR-2W, TR-2. Universal Wall Trim Ring (White, Red). SBBWL, SBBRL. Wall Surface Mount Back Box (White, Red). SBBGWL, SBBGRL. Compact Wall Surface Mount Back Box (White, Red). Notes: All -P models have a plain housing (no FIRE marking on cover). All -SP models have FUEGO marking on cover. All -ALERT models have ALERT marking on cover. ULC-listed A models have FIRE/FEU marking on cover. NOTIFIER and SpectrAlert are registered trademarks and Sync Circuit is a trademark of Honeywell International Inc by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. Page 4 of 4 DN-60918:A 12/13/2016PRELIMINARY This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) , FAX: (203)

23 Field-Selectable Emergency Communications Devices PRELIMINARY DN-60921:A Audio/Visual Devices General The L-Series emergency communications devices and accessories combine application versatility with all the time- and money-saving benefits of the L-Series line. The L-Series of Audio Visual devices has the broadest and most versatile line of notification devices available. It includes a wide range of devices to meet emergency communications application requirements. ALERT-printed on white housings amber lens strobes and speaker strobes provide visual signaling for emergency communications in compliance with ANSI/UL Standard for General Signaling Visible Appliances. Other Plain or ALERTprinted models provide clear lenses for use with color lens strobe attachments (amber, blue, green, and red) that easily attach to strobe and speaker strobe devices without a candela derating. In addition, L-Series emergency communications devices include plain (non-printed) strobes, horn strobes, and speaker strobes. These devices, along with ALERT-printed devices and L-Series accessories, can meet a wide range of requirements for indoor applications, including emergency communications, general signaling, severe weather, and emergency response. All L-Series emergency communications and general signaling devices are compatible with the entire L-Series line and include all the same time- and money-saving innovations. For example, plug in design simplifies installation and reduces costly ground faults, universal mounting plates with onboard shorting springs test wiring continuity to speed installation and protect devices from damage, and field-selectable settings provide versatility and enable installers to quickly set each device to meet application requirements. Emergency Communications Features Plain or ALERT-printed white housings. Clear or Amber lens strobes and speaker strobes. Color lens attachments for use with clear lens wall or ceiling strobes. Meets DoD specification requirements. L-Series Features Plug-in design for simplified installation. Mounting plate shorting spring easily tests wiring continuity. Automatic selection of 12- or 24-volt operation at 15 and 30 candela. Field-selectable candela settings of: Wall: 15, 30, 75, 95, 110, 135, 185. Ceiling: 15, 30, 75, 95, 115, 150, 177. Rated from 32 F to 120 F (indoor devices); 40 F to 151 F (NEMA 4X, IP56 weatherproof devices). Optional tamper-resistant Torx head screw. Compatible with System Sensor synchronization protocol. SPSCWL-CLR-ALERT, P2RL-P, SWL-CLR-ALERT L-Series Specifications ARCHITECTURAL/ENGINEERING SPECIFICATIONS General: System Sensor L-Series strobes and horn strobes shall mount to a standard 4" 4" 1½" back box, 4" octagon back box, or double-gang back box. L-Series Compact shall mount to a single-gang 2" 4" 1 7 / 8 " back box. L-Series speaker strobes shall mount to a 4" x 4" x 2 1 / 8 " back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit wiring and amplifier wiring shall terminate at the universal mounting plate. Also, L-Series products, when used with the Sync Circuit Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync Circuit Module, 12- volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply. Strobes, horn strobes, and speaker strobes shall have field-selectable candela settings, including 15, 30, 75, 95, 110, 115, 135, 150, 177, and 185. Strobe: The clear strobe shall be a System Sensor L-Series Model listed to UL 1971 and shall be approved for fire protective service. Colored lens strobes shall be listed to ANSI/UL 1638 and shall be approved for Private Mode Emergency. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination: The horn strobe shall be a System Sensor L-Series Model listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/ PRELIMINARY DN-60921:A 12/13/2016 Page 1 of 4

24 reflector system. The horn shall have three audibility options and an option to switch between a temporal three-pattern and a non-temporal (continuous) pattern. These options shall be set by a multiple position switch. The horn and horn strobe models shall operate on a coded or non-coded power supply. Speaker Strobe Combination: The speaker strobe shall be a System Sensor L-Series Model listed to UL 1480 and UL 1971 and be approved for fire protective signaling systems. Speaker shall be capable of operating at 25.0 or 70.7 nominal Vrms selected via rotary switch, and shall have a frequency range of 400 to 4,000 Hz. Speaker shall have power taps that are selected by rotary switch. The strobe shall comply with the NFPA 72 requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Synchronization Module: The module shall be a System Sensor Sync Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize L-Series strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn strobe models over a single pair of wires. The module shall mount to a 4 11 / 16 " 4 11 / 16 " 2 1 / 8 " back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Color Lens Strobe Attachment: The System Sensor L-Series color lens attachments shall be approved for fire protective service as listed in UL The lens attachments shall only be used with (plain non-fire-printed) System Sensor strobe devices. They shall mount to any wall or ceiling strobe and be rated from minus 35 degrees to 151 degrees Fahrenheit. Speaker Sound Output UL Reverberant 10 ft.) 2 W 1 W ½ W ¼ W Wall-Mount SPS Series Ceiling-Mount SPC Series Physical Specifications Standard Operating Temperature: 32 F to 120 F (0 C to 49 C) Humidity Range: 10 to 93% non-condensing. Dimensions Wall-Mount Strobe and Horn Strobe (including lens): 5.6" L x 4.7" W x 1.25" D. SPS Speaker Strobe: 6.5" L x 5.0" W x 2.3" D (including lens and speaker) Ceiling-Mount Strobe (including lens): 6.8" diameter x 2.8" D Electrical/Operating Specifications Nominal Voltage (strobes and horn strobes): Regulated 12 VDC or regulated 24 DC/FWR. Nominal Voltage (speakers): 25 V or 70.7 V (nominal). Maximum Supervisory Voltage (speakers): 50 VDC. Operating Voltage Range: 8 to 17.5 V (12 V nominal) or 17 to 33 V (24 V nominal). Operating Voltage Range with MDL3: 8.5 to 17.5 (12V nominal) or 16.5 to 33V (24V nominal). Strobe Flash Rate: 1 flash per second. Speaker Frequency Range: 400 to 4,000 Hz. Speaker Power: ¼, ½, 1, 2 watts. Page 2 of 4 DN-60921:A 12/13/2016PRELIMINARY

25 UL Current Draw Data UL MAX. STROBE CURRENT DRAW (MA RMS) Volts Volts Candela DC DC FWR N/A N/A N/A N/A N/A N/A N/A N/A Wall Candela Settings: 15, 30, 75, 95, 115, 150, 177 Ceiling Candela Settings: 15, 30, 75, 95, 110, 135, 185 UL MAX. CURRENT DRAW (MA RMS), 2-WIRE HORN STROBE DC Input: DC Input: Volts Volts FWR Input: 16 FWR EM Temp Hi EM Temp Low EM Cont Hi EM Cont Low K Temp Hi K Temp Low K Cont Hi k Cont Low HORN TONES AND SOUND OUTPUT DATA: HORN AND HORN STROBE OUTPUT (DBA) Volts Volts Volts FW Position Sound Pattern DC DC R DC 1 Temporal High Temporal Low Non-Temporal High Non-Temporal Low KHz Temporal High KHz Temporal Low KHz Non-Temporal High KHz Non-Temporal Low Coded High KHz Coded High PRELIMINARY DN-60921:A 12/13/2016 Page 3 of 4

26 Agency Listings and Approvals L-series devices have been submitted for agency approvals. Consult factory for latest listing status. Product Line Information Note: A model devices are ULC listed and include required French labeling. All -P models have a plain housing (no "FIRE" marking on cover). ALERT DEVICES SWL-CLR-ALERT(A). Strobe, Wall, Clear Lens, Alert (White). SWL-ALERT. Strobe, Wall, Amber Lens, Alert (White). SCWL-CLR-ALERT(A). Strobe, Ceiling, Clear Lens, Alert (White). SPSWL-ALERT. Speaker Strobe, Wall, Amber Lens, Alert (White). SPSWL-CLR-ALERT(A). Speaker Strobe, White, Wall, Clear Lens, Alert. SPSCWL-CLR-ALERT(A). Speaker Strobe, Ceiling, Clear Lens, Alert (White). PLAIN WALL STROBES SWL(A)-P, SRL(A)-P. Strobe, Wall, Plain (White, Red). PLAIN WALL HORN STROBES P2WL(A)-P, P2RL(A)-P. Horn Strobe, Wall, Plain (White, Red). PLAIN WALL SPEAKER STROBES SPSWL(A)-P, SPSRL(A)-P. Speaker Strobe, Wall, Plain (White, Red). PLAIN CEILING SPEAKER STROBES SPSCWL(A)-P. Speaker Strobe, Ceiling, Plain (White). COLORED LENSES LENS-A2. Wall-Mount Lens Attachment, Amber. LENS-B2. Wall-Mount Lens Attachment, Blue. LENS-G2. Wall-Mount Lens Attachment, Green. LENS-R2. Wall-Mount Lens Attachment, Red. LENS-AC2. Ceiling-Mount Lens Attachment, Amber. LENS-BC2. Ceiling-Mount Lens Attachment, Blue. LENS-GC2. Ceiling-Mount Lens Attachment, Green. LENS-RC2. Ceiling-Mount Lens Attachment, Red. BEZEL KITS* BZW, BZR. Wall Bezel Kit (White, Red). BZGW, BZGR. Compact Wall Bezel Kit (White, Red). BZWC, BZRC. Horn/Strobe Ceiling Bezel Kit (White, Red). BZSPW, BZSPR. Speaker Wall Red Bezel Kit (White, Red). BZSPWC, BZSPRC. Speaker Ceiling Red Bezel Kit. (White, Red). Notes: For bezel option add -F (FIRE), -AL (ALERT), -EV (EVAC), - AG (AGENT), -P (Plain), -SP (FUEGO), -PG (FOGO) for desired printing. Each bezel pack ships in a package of 5. NOTIFIER and SpectrAlert are registered trademarks and Sync Circuit is a trademark of Honeywell International Inc by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. Page 4 of 4 DN-60921:A 12/13/2016PRELIMINARY This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) , FAX: (203)

27 8-Inch Dual Voltage Speaker for Fire and General Signaling Systems PRELIMINARY DN-60915:A General The SPCW8 8" ceiling speaker with listed enclosure provides a solution for ceiling-mount applications, with tap-setting range between 1 / 8 Watt and 8 Watts. It provides a solution for almost any voice need. The high db output reduces the number of speakers required for sound and intelligibility. The SPCW8 is designed for high efficiency sound output with low total harmonic distortion to offer high fidelity sound output. Its clear audibility is designed to meet life safety needs from fire to emergency communication messages. With its wide frequency range it can also be used for general signaling such as paging and background music. The SPCW8 speaker is listed to ANSI/UL 1480, CAN/ULC S541 and CSA C22.2. No. 205 requirements for public mode and general signaling applications as well as ANSI/UL 2043 plenum rated. Speaker is suitable for indoor and damp installations. The SPCW8 can be surface mounted with the included back can or flush mounted with optional accessory, SB-SPC8. The SB-SPC8 (sold separately) offers support for ceiling tile installations, and ¾" knockouts are provided for conduit entry and are compatible with plenum rated cable and plenum whip flex conduit. Features Voltage and speaker tap settings via jumper connection. Field selection of speaker voltage (25 and 70.7 Vrms) and power settings ( 1 / 8, ¼, ½, 1, 2, 4, and 8 watts). For use with separately sold tile support bracket: SB-SPC8. Flush and ceiling tile mounting with use of ceiling tile bracket. UL and ULC listed. Broad temperature range 32 F to 120 F (0 C to 49 C). Accepts wire up to 12 AWG. Speaker ships with included back can. Architectural/Engineering Specifications The SPCW8 8" dual voltage speaker and enclosure shall mount using SB-SPC8 mounting bracket, sold separately. The SPCW8 can be flush mounted with supplied back can or ceiling mounted with back can and SB-SPC8 tile bridge. The speaker shall be a SPCW8 dual-voltage transformer speaker capable of operating at 25.0 or 70.7 nominal Vrms with field selectable tap settings from 1 / 8 to 8 Watts. It should be listed to ANSI/UL 1480, CAN/ULC S541 and CSA C22.2 No. 205 requirements for public mode and general signaling applications as well as ANSI/UL 2043 plenum rated. Speaker is suitable for indoor and damp installations. The speaker shall have a frequency range of 400 to 4,000 Hz and shall have an operating temperature between 32 F and 120 F (0 C and 49 C). The speaker shall have power taps and voltage that are selected by jumper connection. SPCW8 Speaker Physical Specifications Audio/Visual Devices Operating Temperature: 32 F to 120 F (0 C to 49 C). Humidity Range: 10 to 93% non-condensing. Dimensions, Ceiling-Mount: SPCW8 Speaker with Grill: Diameter 12.8 in. (325.1 mm). Depth 2.7 in. (68.6 mm). SPCW8 Speaker with Back Can: Diameter 12.8 in. (325.1 mm). Depth 4.2 in. (106.7 mm). SB-SPC8 Tile Support Bracket: Length in. (603.3 mm). Width in. (104.8 mm). Diameter Opening in. (273.1 mm). Electrical/Operating Specifications Nominal Voltage (speakers): 25 Volts or 70.7 Volts (nominal). Maximum Supervisory Voltage (speakers): 50 VDC. Operating Voltage Range (includes fire alarm panels with built in sync): 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal). Frequency Range: 400 to 4,000 Hz (Fire Alarm), 200Hz - 15KHz (General Signaling). Power: 1 / 8, ¼, ½, 1, 2, 4, 8 watts. Input Terminal Wire Gauge: 12 to 18 AWG. UL Current Draw Data SPC-W8 Sound Output Setting UL Reverberant ft) UL Anechoic ft) 1 / 8 W ¼ W ½ W W W W W PRELIMINARY DN-60915:A 12/13/2016 Page 1 of 2