S F IT 6" / 8"HES. Quick Installation Guide. franklinwater.eu

Transcription

1 GB D S F IT 6" / 8"HES Quick Installation Guide franklinwater.eu

2 Summary Page English 5-19 Deutsch Svenska French Italian

3 GB 6" / 8"HES Quick Installation Guide franklinwater.eu

4 Summary Page Control modes and necessary sensor technologies 5 Battery Installation Procedure IP66 / IP21 5 Connection Description 6"/ 8" HES Sytem Standard 6 System and Connection Description 6" HES solar 7 Connections Motor and Option cards 8 6"/8" System Performance Data 400V-50Hz 9 Keypad button Overview 10 Start-Up-Wizard 10 Basic Con guration 11 / 12 Con guration 13 / 14 Con guration h 15 Con guration P 16 Direct Mode (DM) 17 Manual Mode (MM) 17 Display Messages 18 Con guration S (Solar) 19 Additional safety instructions System can automatically restart (Solar) - the appropiate safety precautions should be taken. See page 19 DANGER 4

5 Control modes and necessary sensor technologies Process reference Control reference Flow meter Pressure sensor Level sensor PT100 sensor & Drive slot card Flow switch (digital) - Flow No (Optional) mandatory Optional P mandatory mandatory H mandatory mandatory P - pressure No (Optional) Yes* mandatory Optional Q mandatory mandatory H mandatory mandatory H - level No (Optional) Yes* mandatory Optional Q mandatory mandatory P mandatory mandatory Direct Mode No Yes** No No Optional No Manual Mode No Yes* Solar No Yes* mandatory *please consult Franklin Electric ** need to be evaluated to PLC Battery Installation Procedure IP Battery Installation Procedure IP21 5

6 Connections 6" / 8" HES Standard System Standard I/O Terminal Signal Vref Reference output Analogue input, 2 AI1+ voltage or current Control Reference: AI1, Terminals 2(+), 3(GND) 3 AI1- Analogue input (Connection depending Default setting [V] common on settings) Analogue input, 4 AI2+ voltage or current Analogue input 5 AI2- common 6 24V out 24V aux. voltage 7 GND I/O ground Fig. 1: Input/Output Terminals Process Reference: AI2, Terminals 4(+), 5(GND) Default setting [ma] 8 DI1 Digital input 1 Start/Stop: DI1, Terminals 6(+24V), 8(DI1) 9 DI2 Digital input 2 External Fault: DI2, Terminals 6(+24V), 9(DI2) 10 DI3 Digital input 3 Manual Operation: DI3, Terminals 6(+24V), 10(DI3) 11 CM Common for DI1 - DI6* 12 24V out 24V aux. voltage 13 GND I/O ground 14 DI4 Digital input 4 Set Point - : DI4, Terminals 6(+24V), 14(DI4) 15 DI5 Digital input 5 Set Point + : DI5, Terminals 6(+24V), 15(DI5) 16 DI6 Digital input 6 Reset: DI6, Terminals 6(+24V), 16(DI6) 17 CM Common for DI1 - DI6* Analogue output, 18 AO1+ voltage or current Analogue output 19 AO-/GND common V in 24V aux. input voltage A RS485 Serial bus, negative B RS485 Serial bus, positive * Can be isolated from ground, see chapter wire Sensor Supply + 24V (Terminal 6) Common - AI+ (Terminal 2/4*) 3- wire Sensor Common - Common(Terminal 7) AI- (Terminal 3/5*) 4- wire Sensor Fig. 1.1 : Sensor connection * depending on Reference AI - (Terminal 3/5*) Common(Terminal 7) Supply + 24V (Terminal 6) 0/4-20mA AI+ (Terminal 2/4*) Supply + 24V (Terminal 6) Common Common(Terminal 7) 0/4-20mA+ AI + (Terminal 2/4*) 0/4-20mA - AI- (Terminal 3/5*) Form standard I/O Relays From term. #6 RUN From term. #13 Terminal 21 RO1/1 22 RO1/2 23 RO1/3 24 RO2/1 25 RO2/2 26 RO2/3 Signal Relay output 1 Relay output 2 Operation: RO1, Terminals 22(+24V), 23 Warning/Fault: RO2, Terminals 25(+24V), 24 Fig. 2: Relais Output Connection IP21 IP66 AI1 AI2 A0 AI1 AI2 A0 Fig. 3: Analog Input/Output Signal Selection IP21 IP66 Fig. 4: Digital Input Selection 6

7 6" HES Solar System DC Power Solar PV Array G IP 66 HES Drive Solar B B Heat Sink Flow Switch (required for operation): D Filter C Derating 40 C - 100% 50 C - 75% 60 C - 50% DC Disconnect optional part A Control Switch Full F Pump/Motor Control Switch Empty E H Alternate AC Power (Optional) 2 Level Control Switch Operation optional parts: Connections 6" HES Solar System Standard I/O Terminal Signal Vref Reference output Analogue input, 2 AI1+ voltage or current Analogue input 3 AI1- common Analogue input, 4 AI2+ voltage or current Analogue input 5 AI2- common 6 24V out 24V aux. voltage 7 GND I/O ground 8 DI1 Digital input 1 Start/Stop: DI1, Terminals 6(+24V), 8(DI1) 9 DI2 Digital input 2 Flow Switch: DI2, Terminals 6(+24V), 9(DI2) 10 DI3 Digital input 3 Manual Operation: DI3, Terminals 6(+24V), 10(DI3) 11 CM Common for DI1 - DI6* 12 24V out 24V aux. voltage 13 GND I/O ground 14 DI4 Digital input 4 Control Switch Empty DI4, Terminals 6(+24V), 14(DI4) 15 DI5 Digital input 5 Control Switch Full DI5, Terminals 6(+24V), 15(DI5) 16 DI6 Digital input 6 Reset: DI6, Terminals 6(+24V), 16(DI6) 17 CM Common for DI1 - DI6* Analogue output, 18 AO1+ voltage or current Analogue output 19 AO-/GND common V in 24V aux. input voltage A RS485 Serial bus, negative B RS485 Serial bus, positive * Can be isolated from ground, see chapter Fig. 5: Input/Output Terminals 7

8 Connections Motor and Option cards L1 U/T1 U1 U2 U ~ _ du L2 V1 dt V/T2 V2 V M L3 W/T3 W1 W2 W 3~ PE PE PE PE PE ~ _ Color code FE Motor Short Lead: U - brown V - grey W - black Fig. 6: Supply and motor connection Color code FE PT100 Lead: black 2 - blue 3 - brown Fig. 7: PT100 card (left slot) Fig. 8: PT100 connection Jumper X2 Jumper X4 Fig. 9: OPTB1, 6 DI/DO card Fig. 10: OPT-B4, 1AI/2AO card Red Yellow Green X6 X1 Bus Connector Jumper Interface Board - Connector word 1: motor current word 2: process value word 3: control value word 4: PT100 temperature word 5: motor speed (RPM) word 6: process reference word 7: relay output word 8: output frequency Fig. 11: OPTE5, Pro bus card (right slot) 8

9 6" HES System Performance Data 400V-50Hz 400V/50Hz X16 P N [kw] Thrust F [kn] n N [min -1 ] I N [A] I A / I * N [A] [%] cos [%] T N [Nm] 4 15, ,95 12,9 1 5,5 15, ,95 17,5 1 T A / T N * [Nm] 7,5 15, ,5 0,95 23, X23 9,3 15, ,5 0,95 29, , , , ,5 0,95 41, X , ,5 0,95 46,1 1 18,5 15, , , , X , ,5 0,95 82, , ,5 0,95 95, X , ,95 117,8 1 8" HES System Performance Data 400V-50Hz 400V/50Hz X01 P [kw] Thrust F [kn] n N [min -1 ] I N [A] I A / I * N [A] [%] cos [%] T N [Nm] ,3 0, ,3 0, , T A / T N * [Nm] ,5 0, ,5 0, X ,3 0, , ,7 0, ,2 0, X ,2 0, , ,4 0, Performance data are based on measurements with Franklin Electric original equipment! 9

10 Keypad buttons Overview Move backward in menu Exit edit mode Reset faults with long press Scroll menu up Increase value Move cursor left Move cursor right Stop button Scroll menu down Decrease value Start button Enter active level/item Start-Up-Wizard RUN READY I / O Multimonitor 113 Nominal Amps Nominal Amps Amps Motor Speed 23.0A 20.0A 2300rpm Setpoint Feedback PT m3h 49.5m3h 23.7 C CtrlSetPnt Ctrl. Act. Ctrl. Max. 0.0[-] 0.0[-] 0.0[-] Monitor M 2.1 Multimonitor Trend Curve (12) Basic (12) Monitor M 2.1 Fieldbus Data (20) Trend Curve (4) Basic (1) WIZARD 1171 M Startup wizard Startup wizard M Activate Help Add to Favorites 10

11 Language Selection 802 English Daylight saving 2204 Russia US EU OFF Time :14:11 Min: Max: Year Min: Max: Date Min: Max: During the next steps please enter System Data. Output Filter 1810 du/dt Filter * * PT100 installed 1834 Yes No STOP Not RDY I / O Please note, a PT100 sensor has to be used to measure Motor- Temperature, connected to OPT- BH, terminals 1, 2 and 3. Refere to Quick Installation Guide. next steps please enter Motor Nameplate Data. Motor Nom. Voltage V 400 V 230 V 220 V Nominal Amps 113 Min: 0.26A Max: 5.20A 1.90 A Motor Nom. Frequency Hz 120 Hz During the next steps please enter Duty Point Data. Duty Point Flow 1828 Min: 1.0m³/h Max: 500.0m³/h 75.0 m³/h * for other languages please contact Franklin Electric Europa GmbH ** is only shown and selectable if PT100 Option card is installed 11

12 Basic Con guration Duty Point Head 1829 Pump Install. Depth 1815 Casing Diameter m 50.0 m mm Min: 1.0m Max: 1000m Min: 1.0m Max: m See Fig.12 Min: 100.0mm Max: mm Min. Water Colum 1818 Min: 0.5m Max: 200.0m 10.0 m See Fig.12 During the next steps please enter Process Data. Process Reference 1819 Q [m³/h] Page 13 h [m] P [bar] h P Page 14 Page 16 Direct Mode DM Page 17 Manual Mode MM Page 17 Solar S Page 19 Process Reference has to be connected to AI2, terminals 4(+) and 5(-). Control reference 1 has to be connected to AI1, terminals 2(+) and 3(-). Q, H Flow Inducer SLEEVE PUMP INSTALL. DEPTH Min. Water Column Level Probe Installation Depth Ø D Fig

13 Process Reference 1830 Voltage mA mA Voltage Proc. Ref. End Scale 1034 Min: 0.00m3h Max: 600.0m3h m3h ProcRefSetPntSource 332 Fieldbus Standard Please note, if AI2 is used as Voltage input, you have to set DIP- Switch AI2 to U. Refere to Quick Installation Guide. Control Reference V V ProcRefSetPntSource 332 Fieldbus Standard Proc. Ref. Set Point 167 Min: 31.12m3h Max: m3h 73.0 m3h Control Reference 1820 On Control Reference 1820 On Please note, an analog level meter or analog pressure sensor has to be used as Control Reference 1, connected to AI1, terminals 2(+) and 3(-). See Fig. 1, 1.1 without rotation will start. You can Stop-Button at any time. Having ready to start. RUN READY I / O Multimonitor 113 Nominal Amps Nominal Amps Amps Motor Speed 23.0A 20.0A 2300rpm Setpoint Feedback PT m3h 49.5m3h 23.7 C CtrlSetPnt Ctrl. Act. Ctrl. Max. 0.0[-] 0.0[-] 0.0 [-] 13

14 Con guration h[m] Ctrl. Ref. Signal 1822 h [m] P [bar] Control Reference V V Current LPP Install. Depht 1888 Min: 0.1 m Max: m 20.0m Current If Control Reference Signal is ma, you have to set. DIP- Switch AI1 to I. Refer to Quick Installation Guide. Control Reference mA mA Voltage See Fig. 3 LPP Max. Range 1887 Min: 0.1 m Max: m 10.0m Ctrl. Ref. Set Point 1823 Min: 0.0 m Max: m 0.0 m without rotating will start. You can Stop-Button at any time. Having ready to start. Multimonitor 113 Nominal Amps Nominal Amps Amps Motor Speed 23.0A 20.0A 2300rpm Setpoint Feedback PT m3h 49.5m3h 23.7 C CtrlSetPnt Ctrl. Act. Ctrl. Max. 10.0m 10.5m 25.0 m P[bar] Ctrl. Ref. Signal 1822 h [m] P [bar] Control Reference V V Current Ctrl. Ref. End Scale 1836 Min: 1.0bar Max: bar 25.0 bar Current If Control Reference Signal is ma, you have to set. DIP- Switch AI1 to I. Refer to Quick Installation Guide. Control Reference mA mA Voltage See Fig. 3 Ctrl. Ref. Set Point 1823 Min: 0.5bar Max: 100.0bar 6.0 bar without rotating will start. You can Stop-Button at any time. Having ready to start. Multimonitor 113 Nominal Amps Nominal Amps Amps Motor Speed 23.0A 20.0A 2300rpm Setpoint Feedback PT m3h 49.5m3h 23.7 C CtrlSetPnt Ctrl. Act. Ctrl. Max. 6.0bar 4.5bar 25.0bar 14

15 Con guration h Process Ref. Signal 1830 LPP Install. Depth 1888 LPP Max. Range 1887 ProcRefSetPntSource mA mA Voltage 20.0m Min: 0.1 m Max: m Min: 0.1 m Max: m 10.0m Fieldbus Standard Voltage Please note, if AI2 is used as Voltage input, you have to set DIP- Switch AI2 to U. Refere to Quick Installation Guide. Process Ref. Signal V V ProcRefSetPntSource 332 Fieldbus Standard See Fig. 3 Proc.Ref.Set Point 167 Min: 0.00m Max: 40.00m See Fig. 1, m be used as Control Reference, connected to AI1, terminals 2(+) and 3(-). Current Control Reference V V Current Ctrl. Ref. End Scale m3h Min: 1.0 m3h Max: m3h is ma, you have to set. DIP- Switch AI1 to I. Refer to Quick Installation Guide. Control Reference mA mA See Fig. 3 Ctrl. Ref. Set Point 1823 Min: 31.1m3h Max: 150.0m3h 31.1m3h without rotating will start. You can Stop-Button at any time. Having ready to start. RUN READY I / O Multimonitor 113 Nominal Amps Nominal Amps Amps Motor Speed 23.0A 20.0A 2100rpm Setpoint Feedback PT m 9.0m 23.5 C CtrlSetPnt Ctrl. Act. Ctrl. Max. 31.1m3h 45.0m3h 150.0m3h 15

16 Process Ref. Signal 1830 Proc. Ref. End Scale 1034 ProcRefSetPntSource mA mA Voltage Min: 0.0 bar Max: bar 16.0 bar Fieldbus Standard Voltage Please note, if AI2 is used as Voltage input, you have to set DIP- Switch AI2 to U. Refere to Quick Installation Guide. Process Ref. Signal V V ProcRefSetPntSource 332 Fieldbus Standard See Fig. 3 Proc.Ref.Set Point 167 Min: 0.0 bar Max: 40.0 bar 8.0 bar be used as Control Reference 1, connected to AI1, terminals 2(+) and 3(-). Control Reference V V Current Ctrl. Ref. End Scale m3h Min: 1.0 m3h Max: m3h See Fig. 1, 1.1 Current is ma, you have to set. DIP- Switch AI1 to C. Refer to Quick Installation Guide. Cotrol Reference mA mA See Fig. 3 Ctrl. Ref. Set Point 1823 Min: 31.1 m3h Max: m3h 31.1 m3h without rotating will start. You can Stop-Button at any time. Having ready to start. RUN READY I / O Multimonitor 113 Nominal Amps Nominal Amps Amps Motor Speed 23.0A 20.0A 2300rpm Setpoint Feedback PT bar 6.5bar 23.7 C CtrlSetPnt Ctrl. Act. Ctrl. Max. 31.1m3h 45.0m3h 100.0m3h 16

17 ProcRefSetPntSource 332 Fieldbus Standard without rotating will start. You can Stop-Button at any time. Having ready to start. RUN READY I / O Multimonitor 113 Nominal Amps Nominal Amps Amps Motor Speed 23.0A 20.0A 2300rpm Setpoint Feedback PT % 88.9 % 23.7 C CtrlSetPnt Ctrl. Act. Ctrl. Max. 0.0 [-] 0.0 [-] 0.0 [-] ProcRefSetPntSource 332 Fieldbus Standard If Process Reference has to be connected to AI2, terminals 4 (+) and 5(-). Process Ref. Signal mA mA Voltage Voltage Please note, if AI2 is used as Voltage input, you have to set DIP- Switch AI2 to U. Refere to Quick Installation Guide. Process Ref. Signal V V See Fig. 3 Start/Stop has to be connected to terminal 6 (24V+) and DI1, terminal 8 or can be used by keypad (green/red push buttom). during operation by using DI4 (frequency DOWN) and DI5 (frequency UP) without rotating will start. You can Stop-Button at any time. Having ready to start. Frequency 105 Nominal Amps Output frequency Hz Amps 23.0A 20.0A 89.80Hz PT C 17

18 Display Messages Failure Messages RUN READY ALARM I / O STOP READY ALARM I / O RUN READY ALARM I / O RUN READY ALARM I / O Sleep Alarm Active Code: 81 Alarm Hold Code: 57 PT100 Temperature Alarm Active Code: 70 PT100 Temperature Alarm Active Code: 70 Control Reference Signal out of range. Device is sleeping. Remedy: Check that motor is connected to frequency converter and Run command will not be removed befor completion of Motor temperature critical. Device sleep imminent. Motor temperature critical. Device is sleeping. STOP READY ALARM I / O READY ALARM I / O STOP READY ALARM I / O READY ALARM I / O Sleep Alarm Active Code: 81 Sleep Alarm Active Code: 81 Sleep Alarm Active Code: 81 Sleep Alarm Active Code: 81 Process Reference Signal too low. Device is sleeping. Process Reference Set Point not reached for a period of time. Device is sleeping. Process Reference Signal not reached during a period of time. Control Reference Signal out of range. Device is sleeping. STOP READY ALARM I / O READY ALARM I / O Sleep Alarm Active Code: 81 Sleep Alarm Active Code: 81 Control Reference Signal out of range for several times. Level switch Empty and Full have not plausible switch settings. Warning Faults READY I / O READY I / O Current Limit 1081 Fault: Hold Code: 82 Next Start-Delay active. Please wait, drive will start automatically. Too high Process Refence at low speed for a period of time. Motorcurrent reached Current-Limit. Check Setting and Pump. 18

19 (Attention: During the next steps please enter Solar Panel Data. Panel Voc 1870 Min: 10.0V Max: 100.0V 37.0V Panels per Row 1871 Min: 1 Max: During the next steps please enter control data. On Time : :00 ProcRefSetPntSource 332 Fieldbus Min: 00:00 Max: 20:00 Min: 09:00 Max: 23:59 Standard DI 3 Bypass Solar 1894 Automatic Restart 1896 Yes Yes No No DI 3 Bypass Solar 1894 Yes No Automatic Restart 1896 Yes No Warning: By setting Automatic Restart to yes the motor will start automatically after sun is coming back. Please refer QIG for safety information. Level Switch 1892 One Level Switch Two Level Switches No Level Switch Level Switch 1893 Normal Open (NO) Normal Closed (NC) The Level Switch (Full) has to be connected to terminal 6 (24V+) and DI 5, terminal 15. See Fig. 5, page 7 Level Switch 1892 One Level Switch Two Level Switches No Level Switch Level Switch 1893 Normal Open (NO) Normal Closed (NC) The Level Switch (Full) has to be connected to terminal 6 (24V+) and DI 5, terminal 15. The Level Switch (Empty) has to be connected to terminal 6 (24V+) and DI 4, terminal 14. See Fig. 5, page 7 Level Switch 1892 One Level Switch Two Level Switches No Level Switch Warning: Without Level Switch there is risk to over flood the tank! A Flow Switch has to be connected to DI 2, terminal 6(24V+) and terminal 9. Refer to Quick Installation Guide. See Fig. 5, page 7 without rotating will start. You can Stop-Button at any time. Having ready to start. Frequency 105 Nominal Amps Hz Amps 23.0A 21.9A Motor speed DC- link Voltage 2856 rpm 679 V 19

20 Notes 20

21 Notes 21

22 Franklin Electric Europa GmbH Rudolf-Diesel-Strasse Wittlich/Germany Tel.:+49 (0) 6571 / Fax:+49 (0) 6571 / info@franklinwater.eu 22